There is a misconfiguration in the bios of the gpio pin used for the
interrupt in the T490s. When interrupts are enabled in the tpm_tis
driver code this results in an interrupt storm. This was initially
reported when we attempted to enable the interrupt code in the tpm_tis
driver, which previously wasn't setting a flag to enable it. Due to
the reports of the interrupt storm that code was reverted and we went back
to polling instead of using interrupts. Now that we know the T490s problem
is a firmware issue, add code to check if the system is a T490s and
disable interrupts if that is the case. This will allow us to enable
interrupts for everyone else. If the user has a fixed bios they can
force the enabling of interrupts with tpm_tis.interrupts=1 on the
kernel command line.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Removing IFX0102 from tpm_tis was not a right move because both tpm_tis
and tpm_infineon use the same device ID. Revert the commit and add a
remark about a bug caused by commit 93e1b7d42e ("[PATCH] tpm: add HID
module parameter").
Fixes: e918e57041 ("tpm_tis: Remove the HID IFX0102")
Reported-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acer C720 running Linux v5.3 reports this in klog:
tpm_tis: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis tpm_tis: Could not get TPM timeouts and durations
tpm_tis 00:08: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis 00:08: Could not get TPM timeouts and durations
ima: No TPM chip found, activating TPM-bypass!
tpm_inf_pnp 00:08: Found TPM with ID IFX0102
% git --no-pager grep IFX0102 drivers/char/tpm
drivers/char/tpm/tpm_infineon.c: {"IFX0102", 0},
drivers/char/tpm/tpm_tis.c: {"IFX0102", 0}, /* Infineon */
Obviously IFX0102 was added to the HID table for the TCG TIS driver by
mistake.
Fixes: 93e1b7d42e ("[PATCH] tpm: add HID module parameter")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203877
Cc: stable@vger.kernel.org
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Reported-by: Ferry Toth: <ferry.toth@elsinga.info>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
platform_get_irq() calls dev_err() on an error. As the IRQ usage in the
tpm_tis driver is optional, this is undesirable.
Specifically this leads to this new false-positive error being logged:
[ 5.135413] tpm_tis MSFT0101:00: IRQ index 0 not found
This commit switches to platform_get_irq_optional(), which does not log
an error, fixing this.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()"
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CLKRUN fix caused a few harmless compile-time warnings:
drivers/char/tpm/tpm_tis.c: In function 'tpm_tis_pnp_remove':
drivers/char/tpm/tpm_tis.c:274:23: error: unused variable 'priv' [-Werror=unused-variable]
drivers/char/tpm/tpm_tis.c: In function 'tpm_tis_plat_remove':
drivers/char/tpm/tpm_tis.c:324:23: error: unused variable 'priv' [-Werror=unused-variable]
This removes the variables that have now become unused.
Fixes: 6d0866cbc2d3 ("tpm: Keep CLKRUN enabled throughout the duration of transmit_cmd()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This flag is only used to warn if CLKRUN_EN wasn't disabled on Braswell
systems, but the only way this can happen is if the code is not correct.
So it's an unnecessary check that just makes the code harder to read.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Commit 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell
systems") disabled CLKRUN protocol during TPM transactions and re-enabled
once the transaction is completed. But there were still some corner cases
observed where, reading of TPM header failed for savestate command
while going to suspend, which resulted in suspend failure.
To fix this issue keep the CLKRUN protocol disabled for the entire
duration of a single TPM command and not disabling and re-enabling
again for every TPM transaction. For the other TPM accesses outside
TPM command flow, add a higher level of disabling and re-enabling
the CLKRUN protocol, instead of doing for every TPM transaction.
Fixes: 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Making cmd_getticks 'const' introduced a couple of harmless warnings:
drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)
This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.
Cc: stable@vger.kernel.org
Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The pointer ilb_base_addr does not need to be in global scope, so make
it static.
Cleans up sparse warning:
"symbol 'ilb_base_addr' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
To overcome a hardware limitation on Intel Braswell systems,
disable CLKRUN protocol during TPM transactions and re-enable
once the transaction is completed.
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Now that the platform device was merged for OF support we can use the
platform device to match ACPI devices as well and run everything
through tpm_tis_init.
pnp_acpi_device is replaced with ACPI_COMPANION, and ACPI_HANDLE is
pushed further down.
platform_get_resource is used instead of acpi_dev_get_resources.
The itpm global module parameter is no longer changed during itpm
detection, instead the phy specific bit is set directly.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> (with TPM 2.0)
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (with TPM 1.2)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Replace the open coded IORESOURCE_IRQ with platform_get_irq, which
supports more cases.
Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> (with TPM 2.0)
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (with TPM 1.2)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The test was backwards, triggering IRQ autoprobing if the firmware
did not specify an IRQ, instead of triggering it only when the
module force parameter was specified.
Since autoprobing is not enabled on !x86 and the platform device is
currently only used on !x86, or with force, this has gone unnoticed.
Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> (with TPM 2.0)
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (with TPM 1.2)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add the missing platform_driver_unregister() and remove the duplicate
platform_device_unregister(force_pdev) in the error handling case.
Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Since commit 1107d065fd ("tpm_tis: Introduce intermediate layer for
TPM access") Atmel 3203 TPM on ThinkPad X61S (TPM firmware version 13.9)
no longer works. The initialization proceeds fine until we get and
start using chip-reported timeouts - and the chip reports C and D
timeouts of zero.
It turns out that until commit 8e54caf407 ("tpm: Provide a generic
means to override the chip returned timeouts") we had actually let
default timeout values remain in this case, so let's bring back this
behavior to make chips like Atmel 3203 work again.
Use a common code that was introduced by that commit so a warning is
printed in this case and /sys/class/tpm/tpm*/timeouts correctly says the
timeouts aren't chip-original.
Fixes: 1107d065fd ("tpm_tis: Introduce intermediate layer for TPM access")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This provides an open firwmare driver binding for tpm_tis. OF
is useful on arches where ACPI/PNP is not used.
The tcg,tpm-tis-mmio register map interface is specified by the TCG.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
To avoid code duplication between the old tpm_tis and the new and future
native tcg tis driver(ie: spi, i2c...), the tpm_tis driver was reworked,
so that all common logic is extracted and can be reused from all drivers.
The core methods can also be used from other TIS like drivers.
itpm workaround is now managed with a specific tis flag
TPM_TIS_ITPM_POSSIBLE.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This splits tpm_tis in a high-level protocol part and a low-level interface
for the actual TPM communication. The low-level interface can then be
implemented by additional drivers to provide access to TPMs using other
mechanisms, for example native I2C or SPI transfers, while still reusing
the same TIS protocol implementation.
Though the ioread/iowrite calls cannot fail, other implementations of this
interface might want to return error codes if their communication fails.
This follows the usual pattern of negative values representing errors and
zero representing success. Positive values are not used (yet).
Errors are passed back to the caller if possible. If the interface of a
function does not allow that, it tries to do the most sensible thing it
can, but this might also mean ignoring the error in this instance.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Split priv_data structure in common and phy specific structures. This will
allow in future patches to reuse the same tis logic on top of new phy such
as spi and i2c. Ultimately, other drivers may reuse this tis logic.
(e.g: st33zp24...)
iobase field is specific to TPM addressed on 0xFED4xxxx on LPC/SPI bus.
This commit is based on the initial work by Peter Huewe.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The devm for the IRQ was placed on the chip, not the pdev. This can
cause the irq to be still callable after the pdev has been cleaned up
(eg priv kfree'd).
Found by CONFIG_DEBUG_SHIRQ=y
Reported-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Fixes: 233a065e0cd0 ("tpm: Get rid of chip->pdev")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Remove useless priv field in struct tpm_vendor_specific and take benefit
of chip->dev.driver_data. As priv is the latest field available in
struct tpm_vendor_specific, remove any reference to that structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Move tpm_vendor_specific data related to TCG PTP specification to tpm_chip.
Move all fields directly linked with well known TCG concepts and used in
TPM drivers (tpm_i2c_atmel, tpm_i2c_infineon, tpm_i2c_nuvoton, tpm_tis
and xen-tpmfront) as well as in TPM core files (tpm-sysfs, tpm-interface
and tpm2-cmd) in tpm_chip.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'locality' from struct tpm_vendor_specific migrated it to
the private structures of st33zp24, tpm_i2c_infineon and tpm_tis.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'read_queue' from struct tpm_vendor_specific and make it
available to the various private structures in the drivers.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'irq' from struct tpm_vendor_specific and make it
available to the various private structures in the drivers using irqs.
A dedicated flag TPM_CHIP_FLAG_IRQ is added for the upper layers.
In st33zp24, struct st33zp24_dev declaration is moved to st33zp24.h in
order to make accessible irq from other phy's(i2c, spi).
In tpm_i2c_nuvoton, chip->vendor.priv is not directly allocated. We can
access irq field from priv_data in a cleaner way.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped the field 'iobase' from struct tpm_vendor_specific and migrated
it to the private structures of tpm_atmel and tpm_tis.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Dropped manufacturer_id from struct tpm_vendor_specific and redeclared
it in the private struct priv_data that tpm_tis uses because the field
is only used tpm_tis.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Drop field int_queue from tpm_vendor_specific as it is used only by
tpm_tis. Probably all of the fields should be eventually dropped and
moved to the private structures of different drivers but it is better to
do this one step at a time in order not to break anything.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
rmmod crashes the driver because tpm_chip_unregister() already sets ops
to NULL. This commit fixes the issue by moving tpm2_shutdown() to
tpm_chip_unregister(). This commit is also cleanup because it removes
duplicate code from tpm_crb and tpm_tis to the core.
Fixes: 4d3eac5e156a ("tpm: Provide strong locking for device removal")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Created a local variable pointing to the INT_ENABLE_x register. The
expression clearing INT_ENABLE_x.globalIntEnable is unreadable and
hard to modify without surpassing the 80 char boundary.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Christophe Ricard <christophe-h.ricard@st.com>
Now that we have a proper struct device just use dev_name() to
access this value instead of keeping two copies.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This is a hold over from before the struct device conversion.
- All prints should be using &chip->dev, which is the Linux
standard. This changes prints to use tpm0 as the device name,
not the PnP/etc ID.
- The few places involving sysfs/modules that really do need the
parent just use chip->dev.parent instead
- We no longer need to get_device(pdev) in any places since it is no
longer used by any of the code. The kref on the parent is held
by the device core during device_add and dropped in device_del
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
drivers/char/tpm/tpm_tis.c:838: warning: ‘tpm_tis_resume’ defined but
not used
Reported-by: James Morris <jmorris@namei.org>
Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
cc: stable@vger.kernel.org
In all cases use dev_name() for the mapped resources. This is both
for sake of consistency and also with some platforms resource name
given by ACPI object seems to return garbage.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: 1bd047be37 ("tpm_crb: Use devm_ioremap_resource")
The TPM core has long assumed that every device has a driver attached,
however the force path was attaching the TPM core outside of a driver
context. This isn't generally reliable as the user could detatch the
driver using sysfs or something, but commit b8b2c7d845 ("base/platform:
assert that dev_pm_domain callbacks are called unconditionally")
forced the issue by leaving the driver pointer NULL if there is
no probe.
Rework the TPM setup to create a platform device with resources and
then allow the driver core to naturally bind and probe it through the
normal mechanisms. All this structure is needed anyhow to enable TPM
for OF environments.
Finally, since the entire flow is changing convert the init/exit to use
the modern ifdef-less coding style when possible
Reported-by: "Wilck, Martin" <martin.wilck@ts.fujitsu.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
This does a request_resource under the covers which means tis holds a
lock on the memory range it is using so other drivers cannot grab it.
When doing probing it is important to ensure that other drivers are
not using the same range before tis starts touching it.
To do this flow the actual struct resource from the device right
through to devm_ioremap_resource. This ensures all the proper resource
meta-data is carried down.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
If the ACPI tables do not declare a memory resource for the TPM2
then do not just fall back to the x86 default base address.
Also be stricter when checking the ancillary TPM2 ACPI data and error
out if any of this data is wrong rather than blindly assuming TPM1.
Fixes: 399235dc6e ("tpm, tpm_tis: fix tpm_tis ACPI detection issue with TPM 2.0")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Instead of clearing the global interrupts flag when any device
does not have an interrupt just pass -1 through tpm_info.irq.
The only thing that asks for autoprobing is the force=1 path.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
include/acpi/actbl2.h is the proper place for these definitions
and the needed TPM2 ones have been there since
commit 413d4a6def ("ACPICA: Update TPM2 ACPI table")
This also drops a couple of le32_to_cpu's for members of this table,
the existing swapping was not done consistently, and the standard
used by other Linux callers of acpi_get_table is unswapped.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Wilck, Martin <martin.wilck@ts.fujitsu.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
tpm_tis.c already gets actbl2.h via linux/acpi.h -> acpi/acpi.h ->
acpi/actbl.h -> acpi/actbl2.h, so the direct include in tpm_tis.c
is not needed.
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
auto-probing doesn't work with shared interrupts, and the auto detection
interrupt range is for x86 only.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Now that the probe and run cases are merged together we can use a
much simpler setup flow where probe and normal setup are done with
exactly the same code.
Since the new flow always calls tpm_gen_interrupt to confirm the IRQ
there is also no longer any need to call tpm_get_timeouts twice.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The new code that works directly in tpm_tis_send is able to handle
IRQ probing duties as well, so just use it for everything.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off--by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
IRQ probing needs to know that the TPM is working before trying to
probe, so move tpm_get_timeouts() to the top of the tpm_tis_init().
This has the advantage of also getting the correct timeouts loaded
before doing IRQ probing.
All the timeout handling code is moved to tpm_get_timeouts() in order to
remove duplicate code in tpm_tis and tpm_crb.
[jarkko.sakkinen@linux.intel.com: squashed two patches together and
improved the commit message.]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
This should be done very early, before anything could possibly
cause the TPM to generate an interrupt. If the IRQ line is shared
with another driver causing an interrupt before setting up our
handler will be very bad.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
The interrupt is always allocated with devm_request_irq so it
must always be freed with devm_free_irq.
Fixes: 448e9c55c1 ("tpm_tis: verify interrupt during init")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
If the probing finishes without success, it will leave the value 15 in
the TPM_IRQ_VECTOR register. If the driver is unloaded and reloaded, it
will "think" that the hardware had been programmed with IRQ 15, and will
not probe again.
This patch restores the original value in the IO memory if no IRQ is
probed.
Signed-off-by: Martin Wilck <Martin.Wilck@ts.fujitsu.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
