And switch all callers to use scsi_execute instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dump host state, power info and host/vendor specific registers
on link failures. This provides useful info to debug the failures.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS clock scaling might start kicking in even before the device
is running at the fastest interface speed which is undesirable.
This change moves the clock scaling kick start only after the
device is detected and running at the fastest interface speed.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we are suspending clock scaling during clock gating which doesn't
allow us to have clock gating timeout lower than clock scaling polling
window. If clock gating timeout is smaller than the clock scaling polling
window then we will mostly suspend the clock scaling before clock scaling
polling window expires and we might get stuck in same state (scaled down
or scaled up) for quite a long time. And for this reason, we have clock
gating timeout (150ms) greater than clock scaling polling window (100ms).
We would like to have aggressive clock gating timeout even lower than the
clock scaling polling window hence this change is decoupling the clock
scaling suspend/resume from clock gate/ungate. We will not suspend the
clock scaling as part of clock gating instead clock scaling context will
schedule scaling suspend work if there are no more pending transfer
requests.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever some UFS failure occurs the driver prints the UFS
registers in order to help with analysis of the failure.
However this may not be sufficient in some cases, so having
the host controller state as it is represented and managed in
the driver will contribute to analysis efforts.
Added prints of various fields in the hba struct which may be
of interest.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS driver's load based clock scaling feature scales down the ufs related
clocks in order to allow low power modes of chipsets. UniPro 1.6 supports
maximum gear up to HS-G3 (High Speed Gear3) and some of the chipsets
low power modes may not be allowed in HS-G3 hence this change adds support
to scale gear between HS-G3 and HS-G1 based on same existing load based
clock scaling logic.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Details printed for each request that is aborted can overload the
target as there can be several requests that are aborted at once.
This change will print full request details only for the first
aborted request since the last link reset, and minimal details
for other subsequent requests.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On certain error conditions request abort task itself might fail
when aborting a request. In such case, subsequent request aborts
should skip issuing the abort task as it is expected to fail as well,
and device reset handler will be called next.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King reported that with commit 7ff5ab4736 ("scsi: ufs: add
tracing support") static analysis is reporting that we may have swapped
arguments on calls to:
trace_ufshcd_runtime_resume,
trace_ufshcd_runtime_suspend,
trace_ufshcd_system_suspend,
trace_ufshcd_system_resume,
and trace_ufshcd_init
Where:
hba->uic_link_state is passed to dev_state
hba->curr_dev_pwr_mode is passed to link_state
This wasn't intentional so it's a bug. This change fixed this bug.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull device descriptor reading out of ufs quirk so it can be used also
for other purposes.
Revamp the fixup setup:
1. Rename ufs_device_info to ufs_dev_desc as very similar name
ufs_dev_info is already in use.
2. Make the handlers static as they are not used out of the ufshdc.c
file.
[mkp: applied by hand]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reading big endian value from a buffer requires explicit cast.
Fix sparse warning:
drivers/scsi/ufs/ufshcd.c:4825:24: warning: cast to restricted __be16
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unexport ufshcd_read_device_desc and ufshcd_read_string_desc there is no
really possibility to calling them directly outside of UFS context.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following compilation warning:
drivers/scsi/ufs/ufshcd.c:2076:5: warning: no previous prototype for
ufshcd_query_descriptor_retry [-Wmissing-prototypes]
Also do not export the function, it should not be used out of ufs
context.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Errors such as UIC error, illegal OCS values, and others may require
more information for debugging. Such information could be hibern8 events,
events sequences, recoverable errors, error history, and more.
This patch improves tracking of important errors and events in debug level
to be enabled when debugging a such issues. It includes:
* UIC error history
* Successful hibern8 events
* Successful command after hibern8 exit
* Clk-freq info
* Failed device command
* Infrastructure for dumping host controller debug information
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the ftrace infrastructure to conditionally trace ufs command events.
New trace event is created, which samples the following ufs command data:
- device name
- optional identification string
- task tag
- doorbell register
- number of transfer bytes
- interrupt status register
- request start LBA
- command opcode
Currently we only fully trace read(10) and write(10) commands.
All other commands which pass through ufshcd_send_command() will be
printed with "-1" in the lba and transfer_len fields.
Usage:
echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
cat /sys/kernel/debug/tracing/trace_pipe
Signed-off-by: Lee Susman <lsusman@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the profiling support for some of the time critical
operations like hibern8 enter/exit, clock gating & clock scaling.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Immediately after successful UFS link startup, UFS link power mode would
be in PWM-G1, 1-lane, SLOW-AUTO mode. But currently we are doing few
of the DME local/peer attributes access before setting the "hba->pwr_info"
to default power mode. If we are doing link startup as part of error
recovery then old power mode might be set to FAST mode and doing DME peer
access (after link startup but before updating "hba->pwr_info" to default
power mode) unintentionally tries to switch from FAST to FAST_AUTO mode (if
UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE quirk is enabled).
Above issue is fixed by setting the default power mode immediately after
successful link startup.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS device requires to perform bkops (back ground operations) periodically
but host can control (via auto-bkops parameter of device) when device can
perform bkops based on its performance requirements. In general, host
would like to enable the device's auto-bkops only when it's not doing any
regular data transfer but sometimes device may not behave properly if host
keeps the auto-bkops disabled. This change adds the capability to let the
device auto-bkops always enabled except suspend.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS device and link can be put in multiple different low power modes hence
UFS driver supports multiple different low power modes.
This change sets the default UFS power management level which should put
the link hibernate state and device in sleep state. This default power
management level gives good power savings with relatively less enter/exit
latencies.
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides the sysfs attribute to choose the power management
level for UFS runtime and system suspend.
Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide an option to enable/disable clock scaling during runtime.
Write 1/0 to "clkscale_enable" sysfs node to enable/disable clock
scaling.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide an option to enable/disable clock gating during runtime.
Write 1 or 0 to "clkgate_enable" sysfs node to enable/disable
clock gating.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a command to a W-LU is timed out via scsi, error handling
will treat it as any other LU and send commands such as
START_STOP with wrong format or task abort. Those commands are
illegal for W-LU according to the UFS spec.
To solve it, when an error is recognized those steps are skipped
and the last step, reset and restore process, is initiated.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change adds the ftrace support for following:
1. UFS initialization time
2. Clock gating states
3. Clock scaling states
4. Power management APIs latency
5. BKOPs enable/disable
Usage:
echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
cat /sys/kernel/debug/tracing/trace_pipe
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Inserts driver dumps for UFS Host Controller registers, Transfer Requests
and Task Management Requests.
The dumps will occur on driver initialization failure, ufshcd_abort() and
on error handling path.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
The maximum value PA_SaveConfigTime is 250 (10us) but this is not enough
for some vendors. Gear switch from PWM to HS may fail even with this
max. PA_SaveConfigTime. Gear switch can be issued by host controller as
an error recovery and any software delay will not help on this case so
we need to increase PA_SaveConfigTime to >32us as per vendor
recommendation. This change adds a quirk to increase the
PA_SaveConfigTime parameter.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS HCI v2.1 includes a few additional registers. This change
updates the HCI register, the UFS version register content and the
Interrupt Status register.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We would by default like to run in FAST/SLOW mode instead
of FASTAUTO/SLOWAUTO mode for performance reasons. This
change sets the default speed mode to FAST/SLOW mode.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Consider following sequence of events:
1. UFS is runtime suspended, link_state = Hibern8, device_state = sleep
2. System goes into system suspend, ufshcd_system_suspend() brings both
link and device to active state and then puts the device in Power_Down
state and link in OFF state.
3. System resumes at some later point in time, ufshcd_system_resume()
doesn't do anything as UFS state is runtime suspended. Note that link
is still on OFF state and device is in Power_Down state.
4. Now system again goes into suspend without any UFS accesses before it.
ufshcd_system_suspend() again brings both link and device to active
state and then puts the device in Power_Down state and link if OFF
state. But it's unnecessary to bring the link & device in active state
as both link and device are already in desired low power states. This
change fixes this issue by adding proper state checks in
ufshcd_system_suspend().
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The condition in which error message is printed out was incorrect and
resulted error message only if retries exhausted.
But retries happens only if DME command is a peer command, and thus
DME commands which are not peer commands and fail are not printed out.
This change fixes this issue.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PHY_ADAPTER_ERROR status register indicates PHY lane errors
reported by the M-PHY layer. In some occasions the controller
can recover from such errors. When the error is not recoverable,
a stuck DB error will occur. Since the stuck DB error is spotted
separately, no action other than clearing the register is necessary.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we issue the link startup to the device while its UniPro state is
LinkDown (and device state is sleep/power-down) then link startup
will not move the device state to Active. Device will only move to
active state if the link starup is issued when its UniPro state is
LinkUp. So in this case, we would have to issue the link startup 2
times to make sure that device moves to active state.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices require host PA_TACTIVATE to be higher than
device PA_TACTIVATE otherwise it may get stuck during hibern8 sequence.
This change allows this by using quirk.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is found thats UFS device may take longer than 30ms to respond to
query requests and in this case we might run into following scenario:
1. UFS host SW sends a query request to UFS device to read an attribute
value. SW uses tag #31 for this purpose.
2. UFS host SW waits for 30ms to get the query response (and doorbell
to be cleared by UFS host HW).
3. UFS device doesn't respond back within 30ms hence UFS host SW times
out waiting for the query response.
4. UFS host SW clears the tag#31 from UTRLCLR register.
5. UFS host SW waits until UFS host HW to clear tag#31 from the doorbell
register.
6. UFS host SW retries the same query request on same tag#31 (sends a query
request to device to read an attribute value).
7. UFS host HW gets the query response from the device but this was
intended as a query response for the 1st query request sent (step-1).
8. Now UFS device sends another query response to host (for query request
sent @step-6).
Now there are 2 issues that could happen with above scenario:
1. UFS device should have actually responded back with only one query
response but it is found that device may respond back with 2 query
responses.
2. If UFS device responds back with 2 resposes on same tag, host HW/SW
behaviour isn't predictable.
To avoid running into above scenario, we would basically allow device
to take longer (upto 1.5 seconds) for query response.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reading variable size descriptors (like string descriptor), some UFS
devices may report the "LENGTH" (field in "Transaction Specific fields" of
Query Response UPIU) same as what was requested in Query Request UPIU
instead of reporting the actual size of the variable size descriptor.
Although it's safe to ignore the "LENGTH" field for variable size
descriptors as we can always derive the length of the descriptor from
the descriptor header fields. Hence this change impose the length match
check only for fixed size descriptors (for which we always request the
correct size as part of Query Request UPIU).
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sending query to the device, the index of the failure
is additional useful information that should be printed out as it
might specify the logical unit (LU) where the error occurred.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of the queries might fail during init. To avoid
system failure, we add retry mechanism to issue queries
several times.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controllers may think granularities of PRDT length and
offset as bytes, not double words.
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new ufshcd_state, indicats that an err handler may get to run
immediately. Use UFSHCD_STATE_ERROR here looks not literaly correct.
Signed-off-by: Zang Leigang <zangleigang@hisilicon.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controller may need to configure some things around
hibern8 enter/exit
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controller may need to configure some things before any
task management request is issued
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controller may need to configure some things before any
transfer request is issued.
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch uses the resource-managed to add the devfreq device. This
function will make it easy to handle the devfreq device.
- struct devfreq *devm_devfreq_add_device(struct device *dev,
struct devfreq_dev_profile *profile,
const char *governor_name,
void *data);
Cc: Vinayak Holikatti <vinholikatti@gmail.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we are resuming the UFS device rails in HPM mode, we are first
powering on the VCC rail while VCCQ and VCCQ2 rails still being in LPM
mode. Some UFS devices may take VCC on event as hint that host wants UFS
device to be resumed and may start drawing more power from the
VCCQ/VCCQ2 rails (while they are still in LPM mode) causing voltage drop
on these rails. This change fixes this issue by bringing VCCQ & VCCQ2
rails out of LPM before powering on VCC rail.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently clock scaling is suspended only after the host and device are
put in low power mode but we should avoid clock scaling running after
UFS link is put in low power mode (hibern8). This change suspends clock
scaling before putting host/device in low power mode.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If ufshcd pltfrm/pci driver's probe fails for some reason then ensure
that scsi host is released to avoid memory leak but managed memory
allocations (via devm_* calls) need not to be freed explicitly on probe
failure as memory allocated with these functions is automatically freed
on driver detach.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS devfreq clock scaling work may require clocks to be ON if it need to
execute some UFS commands hence it may request for clock hold before
issuing the command. But if UFS clock gating work is already running in
parallel, ungate work would end up waiting for the clock gating work to
finish and as clock gating work would also wait for the clock scaling
work to finish, we would enter in deadlock state. Here is the call trace
during this deadlock state:
Workqueue: devfreq_wq devfreq_monitor
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
ufshcd_hold
ufshcd_send_uic_cmd
ufshcd_dme_get_attr
ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div
ufs_qcom_clk_scale_notify
ufshcd_scale_clks
ufshcd_devfreq_target
update_devfreq
devfreq_monitor
process_one_work
worker_thread
kthread
ret_from_fork
Workqueue: events ufshcd_gate_work
__switch_to
__schedule
schedule
schedule_preempt_disabled
__mutex_lock_slowpath
mutex_lock
devfreq_monitor_suspend
devfreq_simple_ondemand_handler
devfreq_suspend_device
ufshcd_gate_work
process_one_work
worker_thread
kthread
ret_from_fork
Workqueue: events ufshcd_ungate_work
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
__cancel_work_timer
cancel_delayed_work_sync
ufshcd_ungate_work
process_one_work
worker_thread
kthread
ret_from_fork
This change fixes this deadlock by doing this in devfreq work (devfreq_wq):
Try cancelling clock gating work. If we are able to cancel gating work
or it wasn't scheduled, hold the clock reference count until scaling is
in progress. If gate work is already running in parallel, let's skip
the frequecy scaling at this time and it will be retried once next scaling
window expires.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
