Historically we've exposed the full backlight PWM duty cycle range to
the userspace, in the name of "mechanism, not policy". However, it turns
out there are both panels and board designs where there is a minimum
duty cycle that is required for proper operation. The minimum duty cycle
is available in the VBT.
The backlight class sysfs interface does not make any promises to the
userspace about the physical meaning of the range
0..max_brightness. Specifically there is no guarantee that 0 means off;
indeed for acpi_backlight 0 usually is not off, but the minimum
acceptable value.
Respect the minimum backlight, and expose the range acceptable to the
hardware as 0..max_brightness to the userspace via the backlight class
device; 0 means the minimum acceptable enabled value. To switch off the
backlight, the user must disable the encoder.
As a side effect, make the backlight class device max brightness and
physical PWM modulation frequency (i.e. max duty cycle)
independent. This allows a follow-up patch to virtualize the max value
exposed to the userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we use the runtime IRQ enable/disable functions in our suspend
path, we can simply check the pm._irqs_disabled flag everywhere. So
rename it to catch the users, and add an inline for it to make the
checks clear everywhere.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move it from hsw_power_well_post_enable() (intel_pm.c) to i915_irq.c
so we can reuse the nice IRQ macros we have there. The main difference
is that now we're going to check if the IIR register is non-zero when
we try to re-enable the interrupts.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Traditionally we use genX_ for GT/render stuff and the codenames for
display stuff. But the gt and pm interrupt handling functions on
gen5/6+ stuck out as exceptions, so convert them.
Looking at the diff this nicely realigns our ducks since almost all
the callers are already platform-specific functions following the
genX_ pattern.
Spotted while reviewing some internal rps patches.
No function change in this patch.
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the future, we'll need the height of the fb to fetch from memory for
WM computation.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create and attach the drm property to set aspect ratio. If there is no user
specified value, then PAR_NONE/Automatic option is set by default. User can
select aspect ratio 4:3 or 16:9. The aspect ratio selected by user would
come into effect with a mode set.
v2: Modified switch case to include aspect ratio enum changes
v3: Modified the patch according the change in the earlier patch to return
errno in case property creation fails. With this change, property will be
attached only if creation is successful
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.
- Use frontbuffer tracking bits stuff to separate disable and
re-enable.
- Don't re-check everything in the psr work. We have now accurate
tracking for everything, so no need to check for sprites or tiling
really. Allows us to ditch tons of locks.
- That in turn allows us to properly cancel the work in the disable
function - no more deadlocks.
- Add a check for HSW sprites and force a flush. Apparently the
hardware doesn't forward the flushing when updating the sprite base
address. We can do the same trick everywhere else we have such
issues, e.g. on baytrail with ... everything.
- Don't re-enable psr with a delay in psr_exit. It really must be
turned off forever if we detect a gtt write. At least with the
current frontbuffer render tracking. Userspace can do a busy ioctl
call or no-op pageflip to re-enable psr.
- Drop redundant checks for crtc and crtc->active - now that they're
only called from enable this is guaranteed.
- Fix up the hsw port check. eDP can also happen on port D, but the
issue is exactly that it doesn't work there. So an || check is
wrong.
- We still schedule the psr work with a delay. The frontbuffer
flushing interface mandates that we upload the next full frame, so
need to wait a bit. Once we have single-shot frame uploads we can do
better here.
v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.
v3: s/psr_exit/psr_invalidate/ for consistency
v4: Fixup whitespace.
v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.
v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
by Rodrigo.
- Comments Chris requested to clarify the code.
v7: Fix conflict on rebase (Rodrigo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, after i915_pm_suspend display power wells are staying
power ungated. So, after initiating mem sleep "echo mem > /sys/power/state"
Display is staing D0 State. There might be better way/place to power gate
these wells. Also, we need to make sure that if wells are power gated due to
DPMS OFF sequence, they need not be turned off by i915_pm_suspend again.
v2: Extracted helper for intel_crtc_disable and power gating CRTC power wells.
[Daniel]
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Change-Id: I34c80da66aa24c423a5576c68aa1f3a8d0f43848
Signed-off-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To be able to do this we need to separately keep track of how many
crtcs need a given WRPLL and how many actually actively use it. The
common shared dpll framework already has all this, including massive
state readout and cross checking. Which allows us to do this switch in
a fairly small patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly this patch is one big excersize in deleting code and asserts
which are no longer needed. Note that we still abuse the shared dpll
framework a bit since we call the enable/disable functions from the
crtc mode_set and off hooks. But changing the actual hardware sequence
will be done in the next step.
Note that besides the massive amount of changes in this patch the
places and order in which the low-level WRPLL code is called is
absolutely unchanged.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just boring sed job for preparation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an intel_fb_obj() macro that returns the GEM object associated with
a DRM framebuffer. This macro is safe to call on NULL framebuffers (a
NULL object pointer will be returned in this case).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.
Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg
Ver3: moved SYS_RESTART check earlier, new name for pp_div.
Ver4: Minor issue changes
Ver5: Move registration of reboot notifier to edp_connector_init,
Added warning comment to handler about lack of PM notification.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The always-on power well pixel path on haswell is routed such that it
bypasses the panel fitter when we use is. Which means the pfit CRC
source won't work in that configuration.
Add a new disallow-bypass flags to the pfit pipe config state and set
it when we want to use the pf CRC. Results in a bit of flicker, but
should get the job done. We'll also undo do it afterwards to make sure
other tests arent' negatively affected.
Totally untested due to lack of hsw laptops around here.
v2: s/disallow_bypass/force_power_well_on/ to avoid a double negative
(Damien).
v3: force_thru because roadsigns.
v4: Don't forget the power wells! Also note that until the runtime pm
for DPMS series is fully merged the simple disable/enable trick won't
work since the ->crtc_mode_set callback is still required to do nasty
things. This stuff is tricky, but I think by both fixing up
get_crtc_power_domains and the debugfs wa code we should always
grab/drop the additional power well correctly.
v5: Wrap in () as suggested by Damien to avoid setting reserved values
for the edp transcoder path on bdw+
References: https://bugs.freedesktop.org/show_bug.cgi?id=72864
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The digital ports from Ironlake and up have the ability to distinguish
between long and short HPD pulses. Displayport 1.1 only uses the short
form to request link retraining usually, so we haven't really needed
support for it until now.
However with DP 1.2 MST we need to handle the short irqs on their
own outside the modesetting locking the long hpd's involve. This
patch adds the framework to distinguish between short/long to the
current code base, to lay the basis for future DP 1.2 MST work.
This should mean we get better bisectability in case of regression
due to the new irq handling.
v2: add GM45 support (untested, due to lack of hw)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
[danvet: Fix conflicts in i915_irq.c with Oscar Mateo's irq handling
race fixes and a trivial one in intel_drv.h with the psr code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the CMNRESET deassert is part of the cmnlane power well,
intel_reset_dpio() is called too late to make any difference. We've
deasserted CMNRESET by that time, and so the off+on toggle w/a will
never kick in.
Move the workaround to intel_power_domains_init_hw() where it gets
called before we enable the init power domain.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a slightly different way of readoing out the cdclk in
gmbus_set_freq(). Kill that and just call .get_display_clock_speed().
Also need to remove the GMBUSFREQ update from intel_i2c_reset() since
that gets called way too early. Let's do it in intel_modeset_init_hw()
instead, and also pull the initial vlv_cdclk_freq update there from
init_clock gating.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a standard hook for reading out the current cdclk. Move the VLV
code from valleyview_cur_cdclk() to .get_display_clock_speed().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTuaWZAAoJEHm+PkMAQRiGfkIH/2Hhwrg51GWazUYIXVxz5zLU
kPMlaws3vankbhka9HCg02eS3tkzr6shO3F/qlBba+5GUkUDKCcCisIsvk4hgZZg
7YqepTvcaupNxIp4TmTGm1FYVK1GpaWFdJVgg2PDdGFahw3HSlfZoTkBzirNCwga
p/jfeRzathbUixpz9OAC1AEn2gP1AxNRpSt1wShL5rexBb1YRXCPuCEt9B0UsVoR
mzKf5xEsuaZnpCuvWK4S60fjfVhTe8UJ/xGPPfdLyIXU0rvhaKzfeVQO6F5nIQBy
Xvrar1f7oOPZaJRdlmPvAimS7iS8lq/YctuHu7ia1NdJSihtA5sRPf7cWAw2d7s=
=4PrL
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc4' into drm-intel-next-queued
Due to Dave's vacation drm-next hasn't opened yet for 3.17 so I
couldn't move my drm-intel-next queue forward yet like I usually do.
Just pull in the latest upstream -rc to unblock patch merging - I
don't want to needlessly rebase my current patch pile really and void
all the testing we've done already.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse noticed that the punit communication needed to query the VLV power
well status can cause substantial delays. Since we can query the state
frequently, for example during I2C transfers, maintain a cached version
of the HW state to get rid of this delay.
This fixes at least one reported regression where boot time increased by
~4 seconds due to frequent power well state queries on VLV during eDP
EDID read.
This regression has been introduced in
commit bb4932c4f1
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Apr 14 20:24:33 2014 +0300
drm/i915: vlv: check port power domain instead of only D0 for eDP VDD on
Reported-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So these are the guts of the new beast. This tracks when a frontbuffer
gets invalidated (due to frontbuffer rendering) and hence should be
constantly scaned out, and when it's flushed again and can be
compressed/one-shot-upload.
Rules for flushing are simple: The frontbuffer needs one more full
upload starting from the next vblank. Which means that the flushing
can _only_ be called once the frontbuffer update has been latched.
But this poses a problem for pageflips: We can't just delay the
flushing until the pageflip is latched, since that would pose the risk
that we override frontbuffer rendering that has been scheduled
in-between the pageflip ioctl and the actual latching.
To handle this track asynchronous invalidations (and also pageflip)
state per-ring and delay any in-between flushing until the rendering
has completed. And also cancel any delayed flushing if we get a new
invalidation request (whether delayed or not).
Also call intel_mark_fb_busy in both cases in all cases to make sure
that we keep the screen at the highest refresh rate both on flips,
synchronous plane updates and for frontbuffer rendering.
v2: Lots of improvements
Suggestions from Chris:
- Move invalidate/flush in flush_*_domain and set_to_*_domain.
- Drop the flush in busy_ioctl since it's redundant. Was a leftover
from an earlier concept to track flips/delayed flushes.
- Don't forget about the initial modeset enable/final disable.
Suggested by Chris.
Track flips accurately, too. Since flips complete independently of
rendering we need to track pending flips in a separate mask. Again if
an invalidate happens we need to cancel the evenutal flush to avoid
races.
v3:
Provide correct header declarations for flip functions. Currently not
needed outside of intel_display.c, but part of the proper interface.
v4: Add proper domain management to fbcon so that the fbcon buffer is
also tracked correctly.
v5: Fixup locking around the fbcon set_to_gtt_domain call.
v6: More comments from Chris:
- Split out fbcon changes.
- Drop superflous checks for potential scanout before calling intel_fb
functions - we can micro-optimize this later.
- s/intel_fb_/intel_fb_obj_/ to make it clear that this deals in gem
object. We already have precedence for fb_obj in the pin_and_fence
functions.
v7: Clarify the semantics of the flip flush handling by renaming
things a bit:
- Don't go through a gem object but take the relevant frontbuffer bits
directly. These functions center on the plane, the actual object is
irrelevant - even a flip to the same object as already active should
cause a flush.
- Add a new intel_frontbuffer_flip for synchronous plane updates. It
currently just calls intel_frontbuffer_flush since the implemenation
differs.
This way we achieve a clear split between one-shot update events on
one side and frontbuffer rendering with potentially a very long delay
between the invalidate and flush.
Chris and I also had some discussions about mark_busy and whether it
is appropriate to call from flush. But mark busy is a state which
should be derived from the 3 events (invalidate, flush, flip) we now
have by the users, like psr does by tracking relevant information in
psr.busy_frontbuffer_bits. DRRS (the only real use of mark_busy for
frontbuffer) needs to have similar logic. With that the overall
mark_busy in the core could be removed.
v8: Only when retiring gpu buffers only flush frontbuffer bits we
actually invalidated in a batch. Just for safety since before any
additional usage/invalidate we should always retire current rendering.
Suggested by Chris Wilson.
v9: Actually use intel_frontbuffer_flip in all appropriate places.
Spotted by Chris.
v10: Address more comments from Chris:
- Don't call _flip in set_base when the crtc is inactive, avoids redunancy
in the modeset case with the initial enabling of all planes.
- Add comments explaining that the initial/final plane enable/disable
still has work left to do before it's fully generic.
v11: Only invalidate for gtt/cpu access when writing. Spotted by Chris.
v12: s/_flush/_flip/ in intel_overlay.c per Chris' comment.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.
The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.
Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.
v2: Improve the commit message a bit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.
The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.
If this breaks anything then we need to augment the enable/disable
functions accordingly.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse's SOix work required some patches from acpi-next, so pull it in
through a topic barnch.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables the framework for using MMIO based flip calls,
in contrast with the CS based flip calls which are being used currently.
MMIO based flip calls can be enabled on architectures where
Render and Blitter engines reside in different power wells. The
decision to use MMIO flips can be made based on workloads to give
100% residency for Media power well.
v2: The MMIO flips now use the interrupt driven mechanism for issuing the
flips when target seqno is reached. (Incorporating Ville's idea)
v3: Rebasing on latest code. Code restructuring after incorporating
Damien's comments
v4: Addressing Ville's review comments
-general cleanup
-updating only base addr instead of calling update_primary_plane
-extending patch for gen5+ platforms
v5: Addressed Ville's review comments
-Making mmio flip vs cs flip selection based on module parameter
-Adding check for DRIVER_MODESET feature in notify_ring before calling
notify mmio flip.
-Other changes mostly in function arguments
v6: -Having a seperate function to check condition for using mmio flips (Ville)
-propogating error code from i915_gem_check_olr (Ville)
v7: -Adding __must_check with i915_gem_check_olr (Chris)
-Renaming mmio_flip_data to mmio_flip (Chris)
-Rebasing on latest nightly
v8: -Rebasing on latest code
-squash 3rd patch in series(mmio setbase vs page flip race) with this patch
-Added new tiling mode update in intel_do_mmio_flip (Chris)
v9: -check for obj->last_write_seqno being 0 instead of obj->ring being NULL in
intel_postpone_flip, as this is a more restrictive condition (Chris)
v10: -Applied Chris's suggestions for squashing patches 2,3 into this patch.
These patches make the selection of CS vs MMIO flip at the page flip time, and
make the module parameter for using mmio flips as tristate, the states being
'force CS flips', 'force mmio flips', 'driver discretion'.
Changed the logic for driver discretion (Chris)
v11: Minor code cleanup(better readability, fixing whitespace errors, using
lockdep to check mutex locked status in postpone_flip, removal of __must_check
in function definition) (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # snb, ivb
[danvet: Fix up parameter alignement checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The perfect solution for psr_exit is the hardware tracking the changes and
doing the psr exit by itself. This scenario works for HSW and BDW with some
environments like Gnome and Wayland.
However there are many other scenarios that this isn't true. Mainly one right
now is KDE users on HSW and BDW with PSR on. User would miss many screen
updates. For instances any key typed could be seen only when mouse cursor is
moved. So this patch introduces the ability of trigger PSR exit on kernel side
on some common cases that.
Most of the cases are coverred by psr_exit at set_domain. The remaining cases
are coverred by triggering it at set_domain, busy_ioctl, sw_finish and
mark_busy.
The downside here might be reducing the residency time on the cases this
already work very wall like Gnome environment. But so far let's get focused
on fixinge issues sio PSR couild be used for everybody and we could even
get it enabled by default. Later we can add some alternatives to choose the
level of PSR efficiency over boot flag of even over crtc property.
v2: remove exit from connector_dpms. Daniel pointed this is the wrong way and
also this isn't needed for BDW and HSW anyway.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DRM core will translate calls to legacy cursor ioctls into universal
cursor calls automatically, so there's no need to maintain the legacy
cursor support. This greatly simplifies the transition since we don't
have to handle reference counting differently depending on which cursor
interface was called.
The aim here is to transition to the universal plane interface with
minimal code change. There's a lot of cleanup that can be done (e.g.,
using state stored in crtc->cursor->fb rather than intel_crtc) that is
left to future patches.
v4:
- Drop drm_gem_object_unreference() that is no longer needed now that
we receive the GEM obj directly rather than looking up the ID.
v3:
- Pass cursor obj to intel_crtc_cursor_set_obj() if cursor fb changes,
even if 'visible' is false. intel_crtc_cursor_set_obj() will notice
that the cursor isn't visible and disable it properly, but we still
need to get intel_crtc->cursor_addr set properly so that we behave
properly if the cursor becomes visible again in the future without
changing the cursor buffer (noted by Chris Wilson and verified
via i-g-t kms_cursor_crc).
- s/drm_plane_init/drm_universal_plane_init/. Due to type
compatibility between enum and bool, everything actually works
correctly with the wrong init call, except for the type of plane that
gets exposed to userspace (it shows up as type 'primary' rather than
type 'cursor').
v2:
- Remove duplicate dimension checks on cursor
- Drop explicit cursor disable from crtc destroy (fb & plane
destruction will take care of that now)
- Use DRM plane helper to check update parameters
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Pallavi G<pallavi.g@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the system to enter the lowest power mode during system freeze.
v2: delete force wake timer at suspend (Imre)
v3: add GT work suspend function (Imre)
v4: use uncore forcewake reset (Daniel)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those LUT where defined in the original sprite patch introducing intel_plane,
but were never used.
commit b840d907fc
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Dec 13 13:19:38 2011 -0800
drm/i915: add SNB and IVB video sprite support v6
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Pimp commit message as suggested by Damien]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Functions that can't fail are such a bliss to work with, it'd be shame
to miss the occasion. The "failure" mode is the DSI connector not being
created, the rest of the initialization can carry on happily.
We weren't even checking that value anyway.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Also convert the missed return statement due to other patches
merged meanwhile.]
[danvet2: Squash in fixup from Damien to remove empty return; at the
end of intel_dsi_init.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"Because our driver assumes only one panel is PSR capable, and we
already have other PSR information on dev_priv instead of intel_dp. If
we ever support multiple PSR panels, we'll have to move struct
i915_psr to intel_dp anyway." (by Paulo)
v2: Avoid more than one setup. Removing initialization
and trusting allocation. (By Paulo Zanoni).
v3: rebase.
v4: Adding comment.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible for userspace to create a big object large enough for a
256x256, and then switch over to using it as a 64x64 cursor. This
requires the cursor update routines to check for a change in width on
every update, rather than just when the cursor is originally enabled.
This also fixes an issue with 845g/865g which cannot change the base
address of the cursor whilst it is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[Antti:rebased, adjusted macro names and moved some lines, no functional
changes]
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Tested-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Cc: stable@vger.kernel.org
Testcase: igt/kms_cursor_crc/cursor-size-change
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a bit like the CMN reset de-assert we do in DPIO_CTL, except
that it resets the whole common lane section of the PHY. This is
required on machines where the BIOS doesn't do this for us on boot or
resume to properly re-calibrate and get the PHY ready to transmit data.
Without this patch, such machines won't resume correctly much of the time,
with the symptom being a 'port ready' timeout and/or a link training
failure.
Note that simply asserting reset at suspend and de-asserting at resume
is not sufficient, nor is simply de-asserting at boot. Both of these
cases have been tested and have still been found to have failures on
some configurations.
v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.
On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.
As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.
v2: Clarify HSW+ situation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write to the primary plane base address registrer when we
enable/disable the primary plane in response to sprite coverage. Those
writes will cause the flip counter to increment which could interfere
with the detection of CS flip completion. We could end up completing
CS flips before the CS has even executed the commands from the ring.
To avoid such issues, wait for CS flips to finish before we toggle the
primary plane on/off.
v2: Rebased due to atomic sprite update changes
Testcase: igt/kms_mmio_vs_cs_flip/setplane_vs_cs_flip
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.
As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in the drm vblank rework from Ville and me. drm core parts acked
by Dave Airlie
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Just a bit of fun around the placement of drm_vblank_on. This merge
resolution has been tested in drm-intel-nightly for a while already.
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have hardware based disable bits on gmch platforms, so need
to block spurious underrun reports in software. Which means that we
_must_ start out with fifo underrun reporting disabled everywhere.
This is in big contrast to ilk/hsw/cpt where there's only _one_
disable bit for all platforms and hence we must allow underrun
reporting on disabled pipes. Otherwise nothing really works,
especially the CRC support since that's key'ed off the same irq
disable bit.
This allows us to ditch the fifo underrun reporting hack from the vlv
runtime pm code and unexport the internal function from i915_irq.c
again. Yay!
v2: Keep the display irq disabling, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.
Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
that means some pretty extensive reworking of our code which
currently does all this while the pipe/port is still off.
I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
encoder.
I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.
The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.
This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.
v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)
v3: Rebased on Paulo's runtime PM changes
v4: Not well validated, but rebase on
commit 730488b2ed
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:12:32 2014 -0300
drm/i915: kill dev_priv->pm.regsave
v5: Rebased on latest code base. (Deepak)
v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)
v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In VBT fields operation mode is 0 for Video mode and 1 for command mode.
This field will be directly used as is in generic panel driver. So
adjust accordingly.
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Squash in patch that exported ilk_wm_max_level.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cherryview has 3 pipes. Some of the pll dpio offset calculation is
based on pipe number. Need to use vlv_pipe_to_channel to calculate the
correct phy channel to use for the pipe.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a mechanism by which we can evade the leading edge of vblank. This
guarantees that no two sprite register writes will straddle on either
side of the vblank start, and that means all the writes will be latched
together in one atomic operation.
We do the vblank evade by checking the scanline counter, and if it's too
close to the start of vblank (too close has been hardcoded to 100usec
for now), we will wait for the vblank start to pass. In order to
eliminate random delayes from the rest of the system, we operate with
interrupts disabled, except when waiting for the vblank obviously.
Note that we now go digging through pipe_to_crtc_mapping[] in the
vblank interrupt handler, which is a bit dangerous since we set up
interrupts before the crtcs. However in this case since it's the vblank
interrupt, we don't actually unmask it until some piece of code
requests it.
v2: preempt_check_resched() calls after local_irq_enable() (Jesse)
Hook up the vblank irq stuff on BDW as well
v3: Pass intel_crtc instead of drm_crtc (Daniel)
Warn if crtc.mutex isn't locked (Daniel)
Add an explicit compiler barrier and document the barriers (Daniel)
Note the irq vs. modeset setup madness in the commit message (Daniel)
v4: Use prepare_to_wait() & co. directly and eliminate vbl_received
v5: Refactor intel_pipe_handle_vblank() vs. drm_handle_vblank() (Chris)
Check for min/max scanline <= 0 (Chris)
Don't call intel_pipe_update_end() if start failed totally (Chris)
Check that the vblank counters match on both sides of the critical
section (Chris)
v6: Fix atomic update for interlaced modes
v7: Reorder code for better readability (Chris)
v8: Drop preempt_check_resched(). It's not available to modules
anymore and isn't even needed unless we ourselves cause
a wakeup needing reschedule while interrupts are off
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new function intel_get_crtc_scanline() that returns the current
scanline counter for the crtc.
v2: Rebase after vblank timestamp changes.
Use intel_ prefix instead of i915_ as is more customary for
display related functions.
Include DRM_SCANOUTPOS_INVBL in the return value even w/o
adjustments, for a bit of extra consistency.
v3: Change the implementation to be based on DSL on all gens,
since that's enough for the needs of atomic updates, and
it will avoid complicating the scanout position calculations
for the vblank timestamps
v4: Don't break scanline wraparound for interlaced modes
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV but probably on other platforms too we depend on RC6
being enabled for RPM, so disable RPM until the delayed RC6 enabling
completes.
v2:
- explain the reason for the _noresume version of RPM get (Daniel)
- use the simpler 'if (schedule_work()) rpm_get();' instead of
'if (!cancel_work_sync()) rpm_get(); schedule_work();'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
... our current modeset code isn't good enough yet to handle this. The
scenario is:
1. BIOS sets up a cloned config with lvds+external screen on the same
pipe, e.g. pipe B.
2. We read out that state for pipe B and assign the gmch_pfit state to
it.
3. The initial modeset switches the lvds to pipe A but due to lack of
atomic modeset we don't recompute the config of pipe B.
-> both pipes now claim (in the sw pipe config structure) to use the
gmch_pfit, which just won't work.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081
Tested-by: max <manikulin@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch and finds out the lowest refresh rate supported for the resolution
same as the fixed_mode.
It also checks the VBT fields to see if panel supports seamless DRRS or not.
Based on above data it marks whether eDP panel supports seamless DRRS or not.
This information is needed for supporting seamless DRRS switch for certain
power saving usecases. This patch is tested by enabling the DRM logs and
user should see whether Seamless DRRS is supported or not.
v2: Daniel's review comments
Modified downclock deduction based on intel_find_panel_downclock
v3: Chris's review comments
Moved edp_downclock_avail and edp_downclock to intel_panel
v4: Jani's review comments.
Changed name of the enum edp_panel_type to drrs_support type.
Change is_drrs_supported to drrs_support of type enum drrs_support_type.
v5: Incorporated Jani's review comments
Modify intel_dp_drrs_initialize to return downclock mode. Support for Gen7
and above.
v6: Incorporated Chris's review comments.
Changed initialize to init in intel_drrs_initialize
v7: Incorporated Jani's review comments.
Removed edp_downclock and edp_downclock_avail. Return NULL explicitly.
Make drrs_state and unnamed struct. Move Gen based check inside drrs_init.
v8: Made changes to track PSR enable/disable throughout system use (instead
of just in the init sequence) for disabling/enabling DRRS. Jani's review
comments.
v9: PSR tracking will be done as part of idleness detection patch. Removed
PSR state tracker in i915_drrs. Jani's review comments.
v10: Added log for DRRS not supported in drrs_init
v11: Modification in drrs_init. suggested by Jani
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_pipe_wm will be used to track the state in different stages
of the watermark update process. For that we need to keep a bit
more state in intel_pipe_wm.
We also need to separate the multi-pipe intel_wm_config computation
from ilk_compute_wm_parameters() as that one deals with the future
state, and we need the intel_wm_config to match the current hardware
state at the time we do the watermark merging for multiple pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we don't keep the hotplug interrupts enabled anymore, we can
kill the regsave struct and just cal the normal IRQ preinstall,
postinstall and uninstall functions. This makes it easier to add
runtime PM support to non-HSW platforms.
The only downside is in case we get a request to update interrupts
while they are disabled, won't be able to update the regsave struct.
But this should never happen anyway, so we're not losing too much.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those values are, global, only used in one function and already stored
in mode_config.cursor_{width,height}.
As a result, this initialization code has been moved from the
crtc_init() function to the global modeset_init() one.
I also renamed CURSOR_{WIDTH,HEIGHT} to MAX_CURSOR_{WIDTH,HEIGHT} to be
more accurate about what these value really are.
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of reading out the CD clock rate from the HW at each modeset, do
this only during driver init and resume and use the cached value during
modeset. This moves things towards a state where the sw and hw side
setup is separated. It's also needed for VLV RPM, where we don't put
device into D0 state until modeset_global_resources is called and thus
can't access any display/gfx registers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.
The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.
This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch we allow larger cursor planes of sizes 128x128
and 256x256.
v2: Added more precise check on size while setting cursor plane.
v3: Changes related to restructuring cursor size restrictions
and DRM_DEBUG usage.
v4: Indentation related changes for setting cursor control and
implementing DRM_CAP_CURSOR_WIDTH and DRM_CAP_CURSOR_HEIGHT
Testcase: igt/kms_cursor_crc
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: G, Pallavi <pallavi.g@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After we removed all the intermediate abstractions, we can rename
these functions to just hsw_{en,dis}able_pc8.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When other platforms add runtime PM support they will also need to
disable interrupts, so move the variable to the runtime PM struct.
Also notice that the longer-term goal is to completely kill the
regsave struct, and I even have patches for that.
v2: - Rebase.
v3: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we already get/put runtime PM every time we get/put any power
domain, and now PC8 and runtime PM are the same thing.
With this, we can also now kill the hsw_{en,dis}able_package_c8
functions.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, when our driver becomes idle for i915.pc8_timeout (default:
5s) we enable PC8, so we save some power, but not everything we can.
Then, while PC8 is enabled, if we stay idle for more
autosuspend_delay_ms (default: 10s) we'll enter runtime PM and put the
graphics device in D3 state, saving even more power. The two features
are separate things with increasing levels of power savings, but if we
disable PC8 we'll never get into D3.
While from the modularity point of view it would be nice to keep these
features as separate, we have reasons to merge them:
- We are not aware of anybody wanting a "PC8 without D3" environment.
- If we keep both features as separate, we'll have to to test both
PC8 and PC8+D3 code paths. We're already having a major pain to
make QA do automated testing of just one thing, testing both paths
will cost even more.
- Only Haswell+ supports PC8, so if we want to add runtime PM support
to, for example, IVB, we'll have to copy some code from the PC8
feature to runtime PM, so merging both features as a single thing
will make it easier for enabling runtime PM on other platforms.
This patch only does the very basic steps required to have PC8 and
runtime PM merged on a single feature: the next patches will take care
of cleaning up everything.
v2: - Rebase.
v3: - Rebase.
- Fully remove the deprecated i915 params since Daniel doesn't
consider them as part of the ABI.
v4: - Rebase.
- Fix typo in the commit message.
v5: - Rebase, again.
- Add a huge comment explaining the different forcewake usage
(Chris, Daniel).
- Use open-coded forcewake functions (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_dp.c
A bit a mess with reverts which differe in details between -fixes and
-next and some other unrelated shuffling.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a small follow-up fix to the series of eDP VDD back and forth
we've had recently. This is effectively a combined revert of three
commits:
commit 2c2894f698fffd8ff53e1e1d3834f9e1035b1f39
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:05:20 2014 -0300
drm/i915: properly disable the VDD when disabling the panel
commit b3064154df
Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Date: Tue Mar 4 00:42:44 2014 +0100
drm/i915: Don't just say it, actually force edp vdd
commit dff392dbd2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Dec 6 17:32:41 2013 -0200
drm/i915: don't touch the VDD when disabling the panel
which shows that we're pretty close back to where we started
already. The first two were basically reverting the last, but missing
the WARN. Add that back. We also OCD the intel_ prefix back to
intel_edp_panel_vdd_on() which was lost somewhere in between. The circle
closes.
For future reference, "drm/i915: don't touch the VDD when disabling the
panel" failed to take into account
commit 6cb49835da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun May 20 17:14:50 2012 +0200
drm/i915: enable vdd when switching off the eDP panel
and
commit 35a38556d9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Aug 12 22:17:14 2012 +0200
drm/i915: reorder edp disabling to fix ivb MacBook Air
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit b3064154df tried to revert commit
dff392dbd2, but wasn't complete, which
resulted in regressions on Haswell. So this commit should fix
b3064154df by undoing what it did and
providing an actual complete revert of
dff392dbd2.
Fixes regression introduced by:
commit b3064154df
Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Date: Tue Mar 4 00:42:44 2014 +0100
drm/i915: Don't just say it, actually force edp vdd
Testcase: igt/pm_pc8
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The functionality remains largerly the same. The main difference is that
i2c-over-aux defer timeouts are increased to be safe for all use cases
instead of depending on DP device type and properties.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Functionality remains largely the same as before.
Note that the retry loops and native reply handling all moved into the
core drm helper functions now.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fix up the stray ; Rodrigo spotted in his review and add a
note to the commit message to answer Rodrigo's question in his review.]
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we allow encoders to indicate whether they can be part of a
cloned set with just one flag. That's not flexible enough to describe
the actual hardware capabilities. Instead make it a bitmask of encoder
types with which the current encoder can be cloned.
For now we set the bitmask to allow DVO+DVO and DVO+VGA, which should
match what the old boolean flag allowed. We will add some more cloning
options in the future.
Note that this patch also removes the encoder.possible_clones setting
from encoder setup code - we compute this dynamically.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add Ville's explanation why removing the encoder
possible_clones is save.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By stuffing the fb allocation into the crtc, we get mode set lifetime
refcounting for free, but have to handle the initial pin & fence
slightly differently. It also means we can move the shared fb handling
into the core rather than leaving it out in the fbdev code.
v2: null out crtc->fb on error (Daniel)
take fbdev fb ref and remove unused error path (Daniel)
Requested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Retrieve current framebuffer config info from the regs and create an fb
object for the buffer the BIOS or boot loader left us. This should
allow for smooth transitions to userspace apps once we finish the
initial configuration construction.
v2: check for non-native modes and adjust (Jesse)
fixup aperture and cmap frees (Imre)
use unlocked unref if init_bios fails (Jesse)
fix curly brace around DSPADDR check (Imre)
comment failure path for pin_and_fence (Imre)
v3: fixup fixup of aperture frees (Chris)
v4: update to current bits (locking & pin_and_fence hack) (Jesse)
v5: move fb config fetch to display code (Jesse)
re-order hw state readout on initial load to suit fb inherit (Jesse)
re-add pin_and_fence in fbdev code to make sure we refcount properly (Je
v6: rename to plane_config (Daniel)
check for valid object when initializing BIOS fb (Jesse)
split from plane_config readout and other display changes (Jesse)
drop use_bios_fb option (Chris)
update comments (Jesse)
rework fbdev_init_bios for clarity (Jesse)
drop fb obj ref under lock (Chris)
v7: use fb object from plane_config instead (Ville)
take ref on fb object (Jesse)
v8: put under i915_fastboot option (Jesse)
fix fb ptr checking (Jesse)
inform drm_fb_helper if we fail to enable a connector (Jesse)
drop unnecessary enabled[] modifications in failure cases (Chris)
split from BIOS connector config readout (Daniel)
don't memset the fb buffer if preallocated (Chris)
alloc ifbdev up front and pass to init_bios (Chris)
check for bad ifbdev in restore_mode too (Chris)
v9: fix up !fastboot bpp setting (Jesse)
fix up !fastboot helper alloc (Jesse)
make sure BIOS fb is sufficient for biggest active pipe (Jesse)
v10:fix up size calculation for proposed fbs (Chris)
go back to two pass pipe fb assignment (Chris)
add warning for active pipes w/o fbs (Chris)
clean up num_pipes checks in fbdev_init and fbdev_restore_mode (Chris)
move i915.fastboot into fbdev_init (Chris)
v11:make BIOS connector config usage unconditional (Daniel)
v12:fix up fb vs pipe size checking (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Early at init time, we can try to read out the plane config structure
and try to preserve it if possible.
v2: alloc fb obj at init time after fetching plane config
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on an early draft from Jesse.
Add support for powering on/off the dynamic power wells on VLV by
registering its display and dpio dynamic power wells with the power
domain framework.
For now power on all PHY TX lanes regardless of the actual lane
configuration. Later this can be optimized when the PHY side setup
enables only the required lanes. Atm, it enables all lanes in all
cases.
v2:
- undef function local COND macro after its last use (Ville)
- Take dev_priv->irq_lock around the whole sequence of
intel_set_cpu_fifo_underrun_reporting_nolock() and
valleyview_disable_display_irqs(). They are short and releasing
the lock in between only makes proving correctness more difficult.
- sanitize local var names in vlv_power_well_enabled()
v3:
- rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict due to my changes in the previous patch.
Also throw in an assert_spin_locked for safety. And finally appease
checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Parts that poke port specific HW blocks like the encoder HW state
readout or connector hotplug detect code need a way to check whether
required power domains are on or enable/disable these. For this purpose
add a set of power domains that refer to the port HW blocks. Get the
proper port power domains during modeset.
For now when requesting the power domain for a DDI port get it for a 4
lane configuration. This can be optimized later to request only the 2
lane power domain, when proper support is added on the VLV PHY side for
this. Atm, the PHY setup code assumes a 4 lane config in all cases.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power domains framework is internal to the i915 driver, so pass
drm_i915_private instead of drm_device to its functions.
Also remove a dangling intel_set_power_well() declaration.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit d9255d5714
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Sep 26 20:05:59 2013 -0300
it became clear that we need to separate the unload sequence into two
parts:
1. remove all interfaces through which new operations on some object
(crtc, encoder, connector) can be started and make sure all pending
operations are completed
2. do the actual tear down of the internal representation of the above
objects
The above commit achieved this separation for connectors by splitting
out the sysfs removal part from the connector's destroy callback and
doing this removal before calling drm_mode_config_cleanup() which does
the actual tear-down of all the drm objects.
Since we'll have to customize the interface removal part for different
types of connectors in the upcoming patches, add a new unregister
callback and move the interface removal part to it.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to reuse this in the fbdev initial config code independently
from any fastboot hacks. So allow a bit more flexibility.
v2: Forgot to git add ...
v3: make non-static (Jesse)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of modifying intel_panel in lvds_init_connector/dsi_init/
edp_init_connector, making changes to move intel_panel->downclock_mode
initialization to intel_panel_init()
v2: Jani's review comments incorporated
Removed downclock_mode local variable in dsi_init and
edp_init_connector
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Jesse's patch to switch the fbdev framebuffer from an embedded
struct to a pointer the kfree in case of an error was missed. Fix this
up by using our own internal fb allocation helper directly instead of
reinventing that wheel.
We need a to_intel_framebuffer cast unfortunately since all the other
callers of _create still look better whith using a drm_framebuffer as
return pointer.
v2: Add an unlocked __intel_framebuffer_create function since our
dev->struct_mutex locking is too much a mess. With ppgtt we even need
it to take a look at the global gtt offset of pinned objects, since
the vma list might chance from underneath us. At least with the
current global gtt lookup functions. Reported by Mika.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that it's a normally kmalloce buffer we can use the usual cleanup
paths. The upside here is that if we get the refcounting wrong will be
able to catch it, since the drm core will complain about leftover
framebuffers and kref about underflows.
v2: Kill intel_framebuffer_fini - no longer needed now that we
refcount all fbs properly and only confusing.
v3: We actually still need to call unregister_private to remove the fb
from the idr and drop the idr reference - the final unref doesn't do
that. So much for remembering my own fb liftime rules. Reported by
Imre Deak.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allocate this struct instead, so we can re-use another allocated
elsewhere if needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: WARN_ON if there's no backing storage attached to an fb,
that's a bug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This debugfs interface will allow intel-gpu-tools test case
to verify if screen has been updated properly on cases like PSR.
v2: Accepted all Daniel's suggestions:
* grab modeset lock
* loop over connector and check DPMS on
* return errors
* use _eDP1 suffix for easy future extension
* don't cache crc_supported neither latest crc
* return crc as a full array and read it at once with aux.
* use 0 to turn TEST_SINK off.
* split the drm_helpers definitions in another patch.
v3: Accepted 2 Damien's suggestion: remove h from printf hexa
and return ENODEV when eDP not present instead of EAGAIN.
v4: Accepted 2 Jani' s suggestion: 1 path for unlock and remove
_retry from aux read.
v5: removing last missing useless _retry (by Damien)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a bit more flexibility here in the future, bits get shuffled
around.
v2: more descriptive commit message (Jani Nikula)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A tiny clean-up to allow better code separation between platforms.
v2: Fix comment placement (put in in i9xx_get_aux_clock_divider()) and
nuke the outdated PCH eDP comment (Jani Nikula)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For HSW+ platforms, enable the 5.4Ghz (HBR2) link rate for devices that support it. The
sink device must report that is supports Displayport 1.2 and the HBR2 bit rate in the
DPCD in order to use HBR2.
Signed-off-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They now also work on vlv, which has the regs somewhere else. And
daring a glance into the looking glass it seems like this
functionality will continue to work the same for the next few hardware
platforms.
So it's better to just remove that misleading prefix and have a bit
shorter code for better readability.
The only exceptions are the panel/backlight functions shared with
intel_ddi.c, those get an intel_ prefix.
While at it make the vdd_on/off functions static.
And one straggler was missing the edp_ in the name, so make everything
neatly OCD.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The eDP spec defines some points where after you do action A, you have
to wait some time before action B. The thing is that in our driver
action B does not happen exactly after action A, but we still use
msleep() calls directly. What this patch does is that we record the
timestamp of when action A happened, then, just before action B, we
look at how much time has passed and only sleep the remaining amount
needed.
With this change, I am able to save about 5-20ms (out of the total
200ms) of the backlight_off delay and completely skip the 1ms
backlight_on delay. The 600ms vdd_off delay doesn't happen during
normal usage anymore due to a previous patch.
v2: - Rename ironlake_wait_jiffies_delay to intel_wait_until_after and
move it to intel_display.c
- Fix the msleep call: diff is in jiffies
v3: - Use "tmp_jiffies" so we don't need to worry about the value of
"jiffies" advancing while we're doing the math.
v4: - Rename function again.
- Move function to i915_drv.h.
- Store last_power_cycle at edp_panel_off too.
- Use msecs_to_jiffies_timeout, then replace the msleep with an
open-coded version that avoids the extra +1 jiffy.
- Try to add units to every variable name so we don't confuse
jiffies with milliseconds.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new_config pointer to intel_crtc which will point to the new pipe
config for said crtc while intel_crtc.config will still contain the old
config during first parts of the modeset operation. This is a step
towards having the entire new state available during the compute phase,
so that we can make accurate decisions about global resource usage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add 'new_enabled' to intel_crtc and precompute it alongside new_encoder
and new_crtc. This will allow making decisions about shared resources
that are affected by the set of active pipes, before we've clobbered
anything for real.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On older generations (gen2, gen3) the GPU requires fences for many
operations, such as blits. The display hardware also requires fences for
scanouts and this leads to a situation where an arbitrary number of
fences may be pinned by old scanouts following a pageflip but before we
have executed the unpin workqueue. This is unpredictable by userspace
and leads to random EDEADLK when submitting an otherwise benign
execbuffer. However, we can detect when we have an outstanding flip and
so cause userspace to wait upon their completion before finally
declaring that the system is starved of fences. This is really no worse
than forcing the GPU to stall waiting for older execbuffer to retire and
release their fences before we can reallocate them for the next
execbuffer.
v2: move the test for a pending fb unpin to a common routine for
later reuse during eviction
Reported-and-tested-by: dimon@gmx.net
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73696
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts are getting out of hand, and now we have to shuffle even
more in -next which was also shuffled in -fixes (the call for
drm_mode_config_reset needs to move yet again).
So do a proper backmerge. I wanted to wait with this for the 3.13
relaese, but alas let's just do this now.
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_pm.c
Besides the conflict around the forcewake get/put (where we chaged the
called function in -fixes and added a new parameter in -next) code all
the current conflicts are of the adjacent lines changed type.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's an accident waiting to happen.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That we can use for debugging purposes.
v2: Use designated initializers for the 'names' array (Paulo Zanoni,
Jani Nikula).
Add a check in case the array has a hole (which can now remain
unnoticed with designated initializers) (Jani Nikula)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (for v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The first piece, intel_ddi_pll_select, finds a PLL and assigns it to
the CRTC, but doesn't write any register. It can also fail in case it
doesn't find a PLL.
The second piece, intel_ddi_pll_enable, uses the information stored by
intel_ddi_pll_select to actually enable the PLL by writing to its
register. This function can't fail. We also have some refcount sanity
checks here.
The idea is that one day we'll remove all the functions that touch
registers from haswell_crtc_mode_set to haswell_crtc_enable, so we'll
call intel_ddi_pll_select at haswell_crtc_mode_set and then call
intel_ddi_pll_enable at haswell_crtc_enable. Since I'm already
touching this code, let's take care of this particular split today.
v2: - Clock on the debug message is in KHz
- Add missing POSTING_READ
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Bikeshed comments.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was supposed to have been killed on the same commit that killed the
function, e1264ebe9f, but I guess the
intel_drv.h reorganization accidentally brought it back.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.
We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.
V2: - Move some functions to intel_pm.c
- Remove useless pm_runtime_allow() call at init
- Remove useless pm_runtime_mark_last_busy() call at get
- Use pm_runtime_get_sync() instead of 2 calls
- Add a WARN to check if we're really awake
V3: - Rebase.
V4: - Don't need to call pci_{save,restore}_state and
pci_set_power_sate, since they're already called by the PCI
layer
- Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't modify the packed infoframe data, so we should keep the
const qualifier in place. Just pass the buffer as 'const void *'
instead of 'const uint8_t *' and we can drop the cast entirely.
v2: Do intel_sdvo_write_infoframe() as well
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If one mode of a internal panel has more than one refresh rate, then a reduced
clock is found for the LFP (LVDS/eDP). This enables switching between low
and high frequency dynamically. Moving downclock calculation to intel_panel
so that it is common for LVDS and eDP.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shovel a bit more of the the code into the setup function, and call
it earlier. Otherwise lockdep is unhappy since we cancel the delayed
resume work before it's initialized.
While at it also shovel the pc8 setup code into the same functions.
I wanted to also ditch the header declaration of the hws pc8 functions,
but for unfathomable reasons that stuff is in intel_display.c instead
of intel_pm.c.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71980
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call intel_display_power_enabled() from
i915_capture_error_state() in IRQ context and then take a mutex. To fix
this add a new intel_display_power_enabled_sw() which returns the domain
state based on software tracking as opposed to reading the actual HW
state.
Since we use domain_use_count for this without locking on the reader
side make sure we increase the counter only after enabling all required
power wells and decrease it before disabling any of these power wells.
Regression introduced in
commit 1b02383464b4a915627ef3b8fd0ad7f07168c54c
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Sep 24 16:17:09 2013 +0300
drm/i915: support for multiple power wells
Note that atm we depend on the value returned by
intel_display_power_enabled_sw() in i915_capture_error_state() to avoid
unclaimed register access reports. This was never guaranteed though,
since another thread can disable the power concurrently. If this is a
problem we need another explicit way to disable the reporting during
error captures.
v2:
- remove barriers as the caller can't depend on the value
returned from i915_capture_error_state_sw() anyway (Ville)
- dump the state of pipe/transcoder power domain state (Daniel)
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV can have eDP on either port B or C, or even both. Based on the
VBT spec, intel_dpd_is_edp() should work on VLV too, assuming we
check the correct ports.
So instead of hardcoding port D, rename the function to
intel_dp_is_edp() and pass the port as a parameter, and use it
on VLV ports B and C.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Wrestle the patch to apply and compile properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prepare for being able to use the information at enable.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The backlight code has grown rather hairy, not least because the
hardware registers and bits have repeatedly been shuffled around. And
this isn't expected to get any easier with new hardware. Make things
easier for our (read: my) poor brains, and split the code up into chip
specific functions.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ALthough usually there's only one connector that supports backlight,
this also finds the correct connector. Before, we only updated the
connector on pipe A, which might not be the one with backlight. (This
only made a difference on BYT.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move from dev_priv to connector->panel. We still don't allow multiple
sysfs interfaces, though.
There should be no functional changes, except for a slight reordering of
connector backlight and sysfs destroy calls. (This change happens now
that the backlight device is actually per-connector, even though the
destroy calls became per-connector earlier.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've always felt the backlight device conditional build has been all
backwards. Make it feel right.
Gently move things towards connector based stuff while at it.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_dpio_read/write should be describe more in PHY centric instead of
display controller centric.
Create a enum dpio_channel for channel index and enum dpio_phy for PHY
index. This should better to gather for upcoming platform.
v2: Rebase the code based on
drm/i915/vlv: Fix typo in the DPIO register define.
v3: Rename vlv_phy to dpio_phy_iosf_port and define additional macro
DPIO_PHY, and remove unrelated change. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, backlight controls a per-pipe, so when adjusting the
backlight we need to pass the correct info. So make the externally
visible backlight functions take a connector argument, which can be used
internally to figure out the pipe backlight to adjust.
v2: make connector pipe lookup check for NULL crtc (Jani)
fixup connector check in ASLE code (Jani)
v3: make sure we take the mode config lock around lookups (Daniel)
v4: fix double unlock in panel_get_brightness (Daniel)
v5: push ASLE work into a work queue (Daniel)
v6: separate ASLE work to a prep patch, rebase (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's possible that the CCK clock could run at a different rate than the
DDR clock, so use the same method to get CCK as the GMBUS code does when
calculating the new CDclk divider in the VLV display code.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly rename the other related functions in the power domain
interface.
Higher level driver code calling these functions knows only about power
domains, not the underlying power wells which may be different on
different platforms. Also these functions really init/cleanup/resume
power domains and only through that all related power wells, so rename
them accordingly.
Note that I left i915_{request,release}_power_well as is, since that
really changes the state only of a single power well (and is HSW
specific). It should also get a better name once we make it more
generic by controlling things through a new audio power domain.
v4:
- use intel prefix instead of i915 everywhere (Paulo)
- use a $prefix_$block_$action format (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we make sure that all power domains are enabled during driver
init and turn off unneded ones only after the first modeset. Similarly
during suspend we enable all power domains, which will remain on through
the following resume until the first modeset.
This logic is supported by intel_set_power_well() in the power domain
framework. It would be nice to simplify the API, so that we only have
get/put functions and make it more explicit on the higher level how this
"power well on during init" logic works. This will make it also easier
if in the future we want to shorten the time the power wells are on.
For this add a new device private flag tracking whether we have the
power wells on because of init/suspend and use only
intel_display_power_get()/put(). As nothing else uses
intel_set_power_well() we can remove it.
This also fixes
commit 6efdf354dd
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Oct 16 17:25:52 2013 +0300
drm/i915: enable only the needed power domains during modeset
where removing intel_set_power_well() resulted in not releasing the
reference on the power well that was taken during init and thus leaving
the power well on all the time. Regression reported by Paulo.
v2:
- move the init_power_on flag to the power_domains struct (Daniel)
v3:
- add note about this being a regression fix too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far the modeset code enabled all power domains if it needed any. It
wasn't a problem since HW generations so far only had one always-on
power well and one dynamic power well that can be enabled/disabled. For
domains powered by always-on power wells (panel fitter on pipe A and the
eDP transcoder) we didn't do anything, for all other domains we just
enabled the single dynamic power well.
Future HW generations will change this, as they add multiple dynamic
power wells. Support for these will be added later, this patch prepares
for those by making sure we only enable the required domains.
Note that after this change on HSW we'll enable all power domains even
if it was the domain for the panel fitter on pipe A or the eDP
transcoder. This isn't a problem since the power domain framework
already checks if the domain is on an always-on power well and doesn't
do anything in this case.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill out the HSW watermark s/w tracking structures with the current
hardware state in intel_modeset_setup_hw_state(). This allows us to skip
the HW state readback during watermark programming and just use the values
we keep around in dev_priv->wm. Reduces the overhead of the watermark
programming quite a bit.
v2: s/init_wm/wm_get_hw_state
Remove stale comment about sprites
Make DDB partitioning readout safer
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a new struct intel_pipe_wm which contains all the
watermarks for a single pipe. Use it to unify the LP0 and LP1+
watermark computations so that we can just iterate through the
watermark levels neatly and call ilk_compute_wm_level() for each.
Also add another tool ilk_wm_merge() that merges the LP1+ watermarks
from all pipes. For that, embed one intel_pipe_wm inside intel_crtc that
contains the currently valid watermarks for each pipe.
This is mainly preparatory work for pre-computing the watermarks for
each pipe and merging them at a later time. For now the merging still
happens immediately.
v2: Add some comments about level 0 DDB split and intel_wm_config
Add WARN_ON for level 0 being disabled
s/lp_wm/merged
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This file is all about the legacy fbdev support. If we want to extract
framebuffer functions, we better put those into a separate file.
Also rename functions accordingly, only two have used the intel_fb_
prefix anyway.
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Boots Just Fine (tm)!
The only glitch seems to be that at least on Fedora the boot splash
gets confused and doesn't display much at all.
And since there's no ugly console flickering anymore in between, the
flicker while switching between X servers (VT support is still enabled)
is even more jarring.
Also, I'm unsure whether we don't need to somehow kick out vgacon, now
that nothing else gets in the way. But stuff seems to work, so I
don't care. Also everything still works as well with VGA_CONSOLE=n
Also the #ifdef mess needs a bit of a cleanup, follow-up patches will
do just that.
To keep the Kconfig tidy, extract all the i915 options into its own
file.
v2:
- Rebase on top of the preliminary hw support option and the
intel_drv.h cleanup.
- Shut up warnings in i915_debugfs.c
v3: Use the right CONFIG variable, spotted by Chon Ming.
Cc: Lee, Chon Ming <chon.ming.lee@intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's try to avoid these confusing negated booleans.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Something already got misplaced (although it's from a patch from
before Paulo's cleanup). Move it to the right spot.
v2: Remove the line to keep a neat block, requested by Paulo.
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The intel_flush_primary_plane name actually tells us which plane
we're talking about.
Also reorganize the internals a bit and add a missing POSTING_READ()
to make sure the hardware has seen the changes by the time we
return from the function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IPS should be OK as long as one plane is enabled on the pipe, but
it does seem to cause problems when going between primary only and
sprite only.
This needs more investigations, but for now just disable IPS whenever
the primary plane is disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I already reorganized the header file, Daniel requested me to
remove those keywords. It seems "checkpath.pl --strict" also doesn't
like "extern" on header files.
At least now we're consistent :)
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions were added before the final PC8 implementation, and
their callers moved to intel_display.c during the code review.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And move it so it doesn't need a forward declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also move it to the top of the file so we can remove the forward
declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel complained that we keep adding stuff to the bottom of the file,
so we constantly have conflicts. So reorganize everything and split
them file-by-file, also sorting the files in alphabetical order. This
way, patches touching different files will have a smaller chance of
conflicting. Of course, this commit will conflict with everybody on
the list :)
Also remove a few useless comments and make some things fit into 80
lines.
v2: - Conflict with intel_ddi_get_config
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Call intel_ddi_get_config() to get the pipe_bpp settings from
DDI.
The sync polarity settings from DDI are irrelevant for CRT
output, so override them with data from the ADPA register.
v2: Extract intel_crt_get_flags()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69691
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the gratious overallocation of crtcs. Seems to go back to the ums
days of yonder ...
We also still need it to make the fbdev emulation happy, but I don't
think there's really a need. Especially since the current fbdev
emulation doesn't actually support cloning.
v2: Use sizeof(*pointer) pattern (Jani).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMORAAoJEHm+PkMAQRiGj14H/1bjhtfNjPdX7MVQAzA+WpwX
s7h1IQu2Si9S5S1lBiM2sBTOssVcmfheO9x4yqm7JNOD1RnssWKOM3q+zVOLstwd
GD3gluJPeraD5EyYSqEJ9ILPQ3gbxb4wOlT0Z291TW6E8XhLRr0RTOJPksRsgvLH
Ckm9uJh6ArS6ZXfXiaDQfd+xHAQJkUfW6nMSA0g9ZO9C6KIDRvcbUmrY3m4HhfIk
mK0TXCBs+AXGDIjTEB8JgIQL/5y1Qn0c4R+2uTU/4YWwyLvJTV1e44kGoleukMMT
6Pw/TNlUEN161dbSaqCyF3sfXHDYQ5valycI2PDgitMtPSxbzsU1VDizS8+daRg=
=lEmF
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc2' into drm-intel-next
Backmerge Linux 3.12-rc2 to prep for a bunch of -next patches:
- Header cleanup in intel_drv.h, both changed in -fixes and my current
-next pile.
- Cursor handling cleanup for -next which depends upon the cursor
handling fix merged into -rc2.
All just trivial conflicts of the "changed adjacent lines" type:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add APIs to get/put power well references for specific purposes.
v2: Split the i915_request change to another patch
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reorganize the internal i915_request power well handling to use the
reference count just like everyone else. This way all we need to do is
check the reference count and we know whether the power well needs to be
enabled of disabled.
v2: Split he intel_display_power_{get,put} change to another patch.
Add intel_resume_power_well() to make sure we enable the power
well on resume
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine the need for double wide mode already in compute_config
stage as we need that information to figure out if horizontal
coordinates need to be adjusted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to clarify the purpose of requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.
Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.
In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.
v2: Add a comment to explain what pipe_src_{w,h} are
Add a note about primary planes to commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract the code to calculate the dotclock from the link clock and M/N
values into a new function from ironlake_crtc_clock_get().
The new function can be used to calculate the dotclock for both FDI and
DP cases.
Also simplify the code a bit along the way.
v2: Don't forget about non-pch encoders in ironlake_crtc_clock_get()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.
Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.
v2: Remember the DDI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It would be easier if adjusted_mode.clock would be the pipe pixel clock,
and it actually is, except for the cases where pixel_multiplier > 1.
So let's change intel_sdvo to use port_clock as the multiplied clock,
and then we can leave adjusted_mode.clock as pipe pixel clock.
v2: Improve port_clock documentation
Rebased on top of SDVO pixel_multiplier fixes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing the appropriate crtc to intel_update_watermarks() should help
in avoiding needless work in the future.
v2: Avoid clash with internal 'crtc' variable in some wm functions
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Detangle the additional state of whether or not the hw has the pfit
enabled from whether it has zero size. This allows us to cleanly
distinguish in the code when we expect the pfit to be enabled (for
Haswell pc8), and when the BIOS is confused and needs sanitizing.
Reported-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68251
Tested-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When transitioning away from vgacon the system tries to save the
current contents of the VGA memory, so that it can be cleanly handed
off to fbcon (or whatever comes afterwards).
The recent change
commit 81b5c7bc8d
Author: Alex Williamson <alex.williamson@redhat.com>
Date: Wed Aug 28 09:39:08 2013 -0600
i915: Update VGA arbiter support for newer devices
caused i915 to disable VGA memory decode for the IGD when i915 is
initializing. Unfortunately that happens before the vgacon->fbcon
handoff so vgacon_save_screen() will read out all ones from the
VGA memory.
After the handoff fbcon will inherit the bogus state from vgacon,
and pre-fills the fb with matching contents. The end result is
a white rectangle in the top left corner of the screen, the size
of which matches the now inactive VGA console.
To remedy the situation delay the disabling of VGA memory until
the vgacon->fbcon handoff has happened.
Also rename i915_enable_vga to i915_enable_vga_mem to make
the relationship between these functions clearer.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for followup work.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This does not include any panel specific sub-encoders yet.
v2: Fix fixed mode handling (Daniel)
v3: Mostly based on Ville's review comments.
- Fix MIPI_HS_TX_TIMEOUT.
- DPI_ENABLE only for video mode.
- Drop ULPS usage for now, use DEVICE_READY only.
- Set MIPI_INIT_COUNT based on txclkesc.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_fixed_panel_mode() overwrote the adjusted_mode with the fixed mode
only partially. Notably it forgot to copy over the sync flags. The LVDS code however programmed the hardware with the sync flags from fixed mode, and then later the pipe config comparison obviously failed as we
filled out the adjusted_mode in get_config from the real registers.
Just call drm_mode_copy() in intel_fixed_panel_mode() to copy over the
whole thing, and then just use adjusted_mode in the LVDS code to figure
out which sync settings the hardware needs.
Also constify the fixed_mode argument to intel_fixed_panel_mode().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch allows PC8+ states on Haswell. These states can only be
reached when all the display outputs are disabled, and they allow some
more power savings.
The fact that the graphics device is allowing PC8+ doesn't mean that
the machine will actually enter PC8+: all the other devices also need
to allow PC8+.
For now this option is disabled by default. You need i915.allow_pc8=1
if you want it.
This patch adds a big comment inside i915_drv.h explaining how it
works and how it tracks things. Read it.
v2: (this is not really v2, many previous versions were already sent,
but they had different names)
- Use the new functions to enable/disable GTIMR and GEN6_PMIMR
- Rename almost all variables and functions to names suggested by
Chris
- More WARNs on the IRQ handling code
- Also disable PC8 when there's GPU work to do (thanks to Ben for
the help on this), so apps can run caster
- Enable PC8 on a delayed work function that is delayed for 5
seconds. This makes sure we only enable PC8+ if we're really
idle
- Make sure we're not in PC8+ when suspending
v3: - WARN if IRQs are disabled on __wait_seqno
- Replace some DRM_ERRORs with WARNs
- Fix calls to restore GT and PM interrupts
- Use intel_mark_busy instead of intel_ring_advance to disable PC8
v4: - Use the force_wake, Luke!
v5: - Remove the "IIR is not zero" WARNs
- Move the force_wake chunk to its own patch
- Only restore what's missing from RC6, not everything
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we're doing with the other IMR changes.
One of the functional changes is that not every caller was doing the
POSTING_READ.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like the functions that touch DEIMR and SDEIMR, but for GTIMR.
The new functions contain a POSTING_READ(GTIMR) which was not present
at the 2 callers inside i915_irq.c.
The implementation is based on ibx_display_interrupt_update.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And also fix a small typo in the intel_encoder_dpms() comment.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're going to want to know the crtc in the watermark code to avoid
doing more work than we have to. We should also pass the plane we're
disabling so that we know where to stick our watermark parameters
without having to go look the plane up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're going to want to know which CRTC we're dealing with, so pass it
down to the update/disable_plane hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Give a name to the plane watermark related data we have currently
stored under intel_plane->wm.
We also observe that this data is more or less the same that we have
in the hsw_pipe_wm_parameters structure, so use it there as well.
v2: Make pahole happier
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the HDMI infoframe code has been ported to use video/hdmi.c, so it's
time to say bye bye to this code.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in the move to the shared infoframe infrastructure, let's
move the different infoframe helpers and the write_infoframe() vfunc to
a type (enum hdmi_infoframe_type) and a buffer + len instead of using
our struct dip_infoframe.
v2: constify the infoframe pointer and don't mix signs (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni at intel.com>
Signed-off-by: Thierry Reding <thierry.reding at avionic-design.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than open-code the teardown of a framebuffer, export the routine
from intel_display.c. This then make intel_fbdev symmetric in its use of
the common intel_framebuffer routines to initialise and clean up the
struct intel_framebuffer. (And new features need only be added in one
location!)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For calculating watermarks we want to know whether sprites are
scaled. Pass that information to update_sprite_watermarks() so that
eventually we may do some watermark pre-computing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the old days of the crtc helpers we've only had the encoder and
crtc ->mode_fixup callbacks. So when the lvds connector wanted to
adjust the crtc timings it had to set a driver-private mode flag to
tell the crtc mode fixup code to not overwrite them with the generic
ones.
When converting things to the new infrastructure I've kept the entire
logic and only moved the flag to pipe_config->timings_set. But this
logic is pretty tricky and already caused regressions:
commit 21d8a4756a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 12 08:07:30 2013 +0200
drm/i915: fix pfit regression for non-autoscaled resolutions
So take advantage of the flexibility our own modeset infrastructure
affords us and prefill default crtc timings. This allows us to rip out
->timings_set. Note that we overwrite things again when retrying the
pipe config computation due to bandwidth constraints to avoid bogus
crtc timings if the encoder only does relative adjustments (which is
how the pfit code works). Only a theoretical concern though since
platforms where we retry (pch-split platforms) do not need
adjustements (since only the old gmch pfit needs that). But let's
better be safe than sorry.
Since we now initialize the crtc timings before calling the
encoder->compute_config functions the crtc initialization in the gmch
pfit code is now redudant and so can be removed.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add a paragraph to the commit message to explain why we can
ditch the crtc timings initialization call from the gmch pfit code, to
answer a question from Rodrigo's review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, the register access code is split between i915_drv.c and
intel_pm.c. It only bares a superficial resemblance to the reset of the
powermanagement code, so move it all into its own file. This is to ease
further patches to enforce serialised register access.
v2: Scan for random abuse of I915_WRITE_NOTRACE
v3: Take the opportunity to rename the GT functions as uncore. Uncore is
the term used by the hardware design (and bspec) for all functions
outside of the GPU (and CPU) cores in what is also known as the System
Agent.
v4: Rebase onto SNB rc6 fixes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Wrestle patch into applying and inline
intel_uncore_early_sanitize (plus move the old comment to the new
function). Also keep the _santize postfix for intel_uncore_sanitize.]
[danvet: Squash in fixup spotted by Chris on irc: We need to call
intel_pm_init before intel_uncore_sanitize since the later will call
cancel_work on the delayed rps setup work the former initializes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218
Merge: 42577ca058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now there are no callers, but these functions are going to be
needed for the code that allows Package C8+. Other future features may
also require this code.
Also merge the commit which introduced assert_can_disable_lcpll and
had the following commit message:
Most of the hardware needs to be disabled before LCPLL is disabled, so
let's add a function to assert some of items listed in the "Display
Sequences for LCPLL disabling" documentation.
The idea is that hsw_disable_lcpll should not disable the hardware,
the callers need to take care of calling hsw_disable_lcpll only once
everything is already disabled.
v2: - Rebase.
- Fix D_COMP wait timeout.
v3: - Use wait_for_atomic_use (Ben)
- Remove/add a useless/needed POSTING_READ (Ben)
- Early return in case LCPLL is already restored (Ben)
- Add ndelay(100) (Ben)
v4: - Merge the commit that added assert_can_disable_lcpll (Ben)
- Add interrupt assertions (Ben)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail since there's no HAS_LP_PCH yet.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required function to disable PSR when going to console mode.
But also can be used whenever PSR mode entry conditions changed.
v2: Add it before PSR Hook. Update function not really been called yet.
v3: Fix coding style detected by checkpatch by Paulo Zanoni.
v4: do_enable must be static as Paulo noticed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding Enable and Disable PSR functionalities. This includes setting the
PSR configuration over AUX, sending SDP VSC DIP over the eDP PIPE config,
enabling PSR in the sink via DPCD register and finally enabling PSR on
the host.
This patch is based on initial PSR code by Sateesh Kavuri and Kumar Shobhit
but in a different implementation.
v2: * moved functions around and changed its names.
* removed VSC DIP unset from disable.
* remove FBC wa.
* don't mask LSPS anymore.
* incorporate new crtc usage after a rebase.
v3: Make a clear separation between Sink (Panel) and Source (HW) enabling.
v4: Fix identation and other style issues raised by checkpatch (by Paulo).
v5: Changes according to Paulo's review:
static on write_vsc;
avoid using dp_to_dev when already calling dp_to_dig_port;
remove unecessary TP default time setting;
remove unecessary interrupts disabling;
remove unecessary wait_for_vblank when disabling psr;
v6: remove unecessary wait_for_vblank when writing vsc;
v7: adding setup once function to avoid unnecessarily write to vsc
and set debug_ctl every time we enable or disable psr.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Sateesh Kavuri <sateesh.kavuri@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Apply Paulo's suggestion for unconditionally clearing the
control register when writing the DIP.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: reuse of just created is_edp_psr and put it at right place.
v3: move is_edp_psr above intel_edp_disable
v4: remove parentheses. Noticed by Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise the DDI_A_4_LANES bit gets lost and we can't use > 2 lanes
on eDP. This fixes eDP on hsw with > 2 lanes.
Also s/port_reversal/saved_port_bits/ since the current name is
confusing.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict with Damien's FBC_CHIP_DEFAULT no fbc
reason.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lots of bangin my head against the wall^UExperiments have shown that
we really need to enable the lvds port before we enable plls. Strangely
that seems to include the fdi rx pll on the pch.
Note that the pch pll assert can fire since the lvds port has it's own
special clock source settings in the DPLL register, which means it
will never have a shared dpll (since there's only one LVDS port).
Anyway, encode this new evidence with a few nice WARNs.
v2: Incorporate review comments from Imre.
- Explain why lvds can't have a shared dpll.
- Update the WARN output.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function has no user outside of intel_pm.c.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On DevCPT, the control register for Transcoder DP Sync Polarity is
TRANS_DP_CTL, not DP_CTL.
Without this patch, Many call trace occur on CPT machine with DP monitor.
The call trace is like: *ERROR* mismatch in adjusted_mode.flags(expected X,found X)
v2: use intel-crtc to simple patch, suggested by Daniel.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[danvet: Extend the encoder->get_config comment to specify that we now
also depend upon intel_encoder->base.crtc being correct. Also bikeshed
s/intel_crtc/crtc/.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65287
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we detect a "ghost eDP", intel_edp_init_connector frees both
the connector and encoder and then returns. On Haswell, intel_ddi_init
then tries to use the freed encoder on the HDMI initialization path
since the following commit:
commit 21a8e6a485
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 10 23:28:35 2013 +0200
drm/i915: don't setup hdmi for port D edp in ddi_init
So now on intel_ddi_init we check for the "ghost eDP" case and return
without trying to initialize HDMI. This way we won't try to read the
freed "intel_encoder" struct in the next "if" statement.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nowadays (i.e. with Valleyview) we also have edp on non-PCH_SPLIT
platforms, so just checking for LVDS is not good enough.
Secondly we have full pfit pipe config tracking, so we'll correctly
disable the pfit as part of the initial modeset.
For fastboot we need a bit of work here to correctly kill unsupported
configs (if e.g. the pfit is used on anything else than the built-in
panel). But since that's not yet supported we don't need to worry.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just the plumbing, all the modeset and enable code has not yet been
switched over to use the new state. It seems to be decently broken
anyway, at least wrt to handling of the special pixel mutliplier
enabling sequence. Follow-up patches will clean up that mess.
Another missing piece is more careful handling (and fixup) of the fp1
alternate divisor state. The BIOS most likely doesn't bother to
program that one to what we expect. So we need to be more careful with
comparing that state, both for cross checking but also when checking
for dpll sharing when acquiring shared dpll. Otherwise fastboot will
deny a few shared dpll configurations which would otherwise work.
v2: We need to memcpy the pipe config dpll hw state into the pll, for
otherwise the cross-check code will get angry.
v3: Don't forget to read the pch pll state in the crtc get_pipe_config
function for ibx/ilk platforms.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't (yet) have proper pixel multiplier readout support on pch
split platforms, so the cross check will naturally fail.
v2: Fix spelling in the comment, spotted by Ville.
v3: Since the ordering constraint is pretty tricky between the crtc
get_pipe_config callback and the encoder->get_config callback add a
few comments about it. Prompted by a discussion with Chris Wilson on
irc about why this does work anywhere else than on i915g/gm.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the big sed-job prep work done this is now really simple. With
the exception that we only assign the right shared dpll id in the
->mode_set callback but also depend upon the old one still being
around.
Until that mess is fixed up we need to jump through a few hoops to
keep the old value save.
v2: Kill the funny whitespace spotted by Chris.
v3: Move the shared_dpll pipe config fixup into this patch as noticed
by Ville. Also unconditionally set the shared_dpll with the current
one, since otherwise we won't handle direct pch port -> cpu edp
transitions correctly.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dealing with discrete enum values is simpler for hw state readout and
pipe config computations than pointers - having neat names instead of
chasing pointers should look better in the code.
This isn't a that good reason for pch plls, but on haswell we actually
have 3 different types of plls: WRPLL, SPLL and the DP clocks. Having
explicit names should help there.
Since this also adds the intel_crtc_to_shared_dpll helper to further
abstract away the crtc -> dpll relationship this will also help to
make the next patch simpler, which moves the shared dpll into the pipe
configuration.
Also note that for uniformity we have two special dpll ids: NONE for
pipes which need a shared pll but don't have one (yet) and private for
when there's a non-shared pll (e.g. per-pipe or per-port pll).
I've thought whether we should also add a 2nd enum for the type of the
pll we want (for really generic pll selection code) but thrown that
idea out again - likely there's too much platform craziness going on
to be able to share the pll selection logic much.
Since this touched all the shared_pll functions a bit I've also done
an s/intel_crtc/crtc/ replacement on a few of them.
v2: Kill DPLL_ID_NONE. It's probably better to call it DPLL_ID_INVALID and use
it to check that the compute config stage assigns a dpll to every pipe.
But since that code isn't ready yet until we move the dpll selection out
of the ->mode_set callback, there's no use for it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For fastboot we need some support to read out the sharing state of
plls, at least for platforms where they can be shared (or freely
assigned at least). Now for ivb we already have pretty extensive
infrastructure for tracking pch plls, and it took us an aweful lot of
tries to get that remotely right. Note that hsw could also share plls,
but even now they're already freely assignable. So we need this on
more than just ivb.
So on top of the usual fastboot fun pll sharing seems to be an
additional step up in fragility. Hence a common infrastructure for all
shared/freely assignable display plls seems to be in order.
The plan is to have a bit of dpll hw state readout code, which can be
used individually, but also to fill in the pipe config. The hw state
cross check code will then use that information to make sure that
after every modeset every pipe still is connected to a pll which still
has the correct configuration - a lot of the pch pll sharing bugs
where due to incorrect sharing.
We start this endeavour with a simple s/pch_pll/shared_dpll/ rename
job.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required for tracking render damage for use with FBC and will be
used in subsequent patches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For various reasons the hw state readout might not be able to
faithfully match the hw state:
- broken hw (like the case which motivated this patch here where the
sdvo encoder does not implemented mandatory functionality
correctly).
- platforms which are not supported fully with the pipe config
infrastructure
- if our code doesn't support a given hw configuration natively, e.g.
special restrictions on the per-pipe panel fitters when they're used
in high-quality scaling modes.
In all these cases both fastboot and the hw state cross checker need
to be aware of these cases and act accordingly. To be able to do this
add a new quirk flag to the pipe config structure.
The specific case at hand is an sdvo encoder which doesn't implement
the get_timings function, so adjusted_mode flags will be wrong. The
strange thing though is that the encoder _does_ work, even though it
doesn't implement any of the timings functions (so neither get nor
set, neither for input nor output timings).
Not that non-compliant sdvo encoder are any surprise at all ...
v2:
- Don't read random garbage from the dtd if the get_timings call
failed (suggested by Chris).
- Still check the interlaced flag, that's read out from someplace
else. We want maximal paranoia, after all.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell Display audio depends on power well in graphic side, it should
request power well before use it and release power well after use.
I915 will not shutdown power well if it detects audio is using.
This patch protects display audio crash for Intel Haswell C3 stepping board.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable/restore sprite planes around mode-set just like we do for the
primary and cursor planes. Now that we have working sprite clipping,
this actually works quite decently.
Previosuly we didn't even bother to disable sprites when changing mode,
which could lead to a corrupted sprite appearing on the screen after a
modeset (at least on my IVB). Not sure if all hardware generations would
be so forgiving when enabled sprites end up outside the pipe dimensons.
v2: Disable rather than enable sprites in ironlake_crtc_disable()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only lvds/tv did actually check for cloning or not, but many more
places should.
Notices because my ivb tried to enable both cpu edp and vga on the
first crtc - the resulting confusion between has_pch_encoder,
has_dp_encoder but not actually being a pch dp encoder resulting in
hilarity (hitting a BUG).
We _really_ need an igt to random-walk our modeset space more
exhaustively.
The bug seems to have been exposed due to a race in the hw load
detection support for VGA: Right after a hotplug VGA was still
detected as connected, but obviously reading the EDID wasn't possible
any more. Hence why restarting X a bit later fixed things. Due to the
1024x756 fallback resolution suddenly more outputs had the same
resolution.
On top of that SNA was confused with the possible_clones mask, trying
to clone outputs which cannot be cloned. That bug is now fixed with
commit fc1e0702b25e647cb423851fb7228989fec28bd6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed May 29 11:25:28 2013 +0100
sna: fixup up possible_clones kms->X impedance mismatch
v2: Kill intel_encoder_check_is_cloned, spotted by Paulo.
v3: Drop the now unused pipe param.
v4: Kill the stray printk Chris spotted.
v5: Elaborate on how the bug in userspace happened and why it was racy
to reproduce.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, whenever we change the sprites we need to completely
recalculate all the watermarks, because the sprites are one of the
parameters to the LP watermarks, so a change on the sprites may
trigger a change on which LP levels are enabled.
So on this commit we store all the parameters we need to store for
proper recalculation of the Haswell WMs and then call
haswell_update_wm.
Notice that for now our haswell_update_wm function is not really using
these parameters we're storing, but on the next commits we'll use
these parameters.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we want to call it from the "sprite disable" paths, since on
Haswell we need to update the sprite watermarks when we disable
sprites.
For now, all this patch does is to add the "enable" argument and call
intel_update_sprite_watermarks from inside ivb_disable_plane. This
shouldn't change how the code behaves because on
sandybridge_update_sprite_wm we just ignore the "!enable" case. The
patches that implement Haswell watermarks will make use of the changes
introduced by this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Group both the HSW/LPT SBI interface and VLV IOSF sideband register
accessor functions into a new file. No functional changes.
v2: also move intel_sbi_{read,write} (Daniel)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec says the linetime watermarks must be programmed before
enabling any display low power watermarks, but we're currently
updating the linetime watermarks after we call intel_update_watermarks
(and only at crtc_mode_set, not at crtc_{enable,disable}). So IMHO the
best way guarantee the linetime watermarks will be updated before the
low power watermarks is inside the update_wm function, because it's
the function that enables low power watermarks. And since Haswell is
the only platform that has linetime watermarks, let's completely kill
the "intel_update_linetime_watermarks" abstraction and just use the
intel_update_watermarks abstraction by creating haswell_update_wm.
For now haswell_update_wm is still calling sandybridge_update_wm, but
in the future I plan to implement a function specific to Haswell.
v2: - Rename patch
- Disable LP watermarks before changing linetime WMs (Chris)
- Add a comment explaining that this is just temporary code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can use this for fetching encoder specific pipe_config state, like
mode flags, adjusted clock, etc.
Just used for mode flags atm, so we can check the pipe config state at
mode set time.
v2: get_config when checking hw state too
v3: fix DVO and LVDS mode flags (Ville)
get SDVO DTD for flag fetch (Ville)
v4: use input timings (Ville)
correct command used (Ville)
remove gen4 check (Ville)
v5: get DDI flag config too
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Tested-by: Paulo Zanoni <przanoni@gmail.com> (the new hsw ddi stuff)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRmpexAAoJEHm+PkMAQRiGrRIH/1uWFW38RvaCV/PXm/ia6Z+x
BfBJfBIvPxGwb4n7aQNQlhU25xkfrPZ6szO4WiBH5/KPH3xYi2I2OZ1AzffkYqMF
BWkPmsPK6EsTdp16zsi6JtH2aXArG4SpYA7ZamPvDkmfigHuiZg7GlL/9eHTRPNV
P7Q8JToOrcnP8RoGgNj0uFiQeQbc62Kmoq7WuPtUhVlpQCCCknXgOJiYgz9w6Xe9
/i79YFS8WRrzAquExT1NbIOh4ZMqB9MvuroaVWy8JDDLUyz7QUvOCe3tCDNguwgi
FdWvU6nfkdQq5SLaWCWXDE9Rp/pL1MvfBn9vCOwFcp42aw0aQ0PgJVIXvsqufd0=
=jgDI
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc2' into drm-intel-next-queued
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to track this correctly. While at it shovel the boolean
to track whether the sdvo is in tv mode or not into pipe_config.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36997
Tested-by: Pierre Assal <pierre.assal@verint.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63609
Tested-by: cancan,feng <cancan.feng@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users for these, so remove them.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For the device to enter D3 we should enable PCH clock gating.
v2:
- use HAS_PCH_LPT instead of IS_HASWELL (Ville, Paolo)
- rename lpt_allow_clock_gating to lpt_suspend_hw (Paolo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should replace intel_using_power_well. The idea is that we're
adding the requested power domain as an argument, so this might enable
the code to look less platform-specific and also allows us to easily
add new domains in case we need.
v2: Add more domains to enum intel_display_power_domain
v3: Even more domains requested
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only one caller. Also drop the intel_ prefix as is now customary for
platform specific and static functions.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is possible thanks to moving the m/n stuff into pipe_config.
Unfortunately we need to move them a bit to avoid forward
declarations.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec the link training sequence for eDP on HSW port-A
should be as follows:
1. link training: clock recovery
2. link training: equalization
3. link training: set idle transmission mode
4. display pipe enable
5. link training: disable (set normal mode)
Contrary to this at the moment we don't do step 3. and we do step 5.
before step 4. Fix this by setting idle transmission mode for eDP at
the end of intel_dp_complete_link_train and adding a new
intel_dp_stop_link_training function to disable link training. With
these changes we'll end up with the following functions corresponding
to the above steps:
intel_dp_start_link_train -> step 1.
intel_dp_complete_link_train -> step 2., step 3.
intel_dp_stop_link_train -> step 5.
For port-A we'll call intel_dp_stop_link_train only after enabling the
pipe, for everything else we'll call it right after
intel_dp_complete_link_train to preserve the current behavior.
Tested on HSW/HSW-ULT.
In v2:
- Due to a HW issue we must set idle transmission mode for port-A too
before enabling the pipe. Thanks for Arthur Runyan for explaining
this.
- Update the patch subject to make it clear that it's an eDP fix, DP is
not affected.
v3:
- rename intel_dp_link_train() to intel_dp_set_link_train(), use 'val'
instead 'l' as var name. (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
pipe_config is the new dev_priv!
More seriously, this is actually better since a pipe_config can be
thrown away if the modeset compute config stage fails. Whereas any
state stored in dev_prive needs to be painstakingly restored, since
otherwise a dpms off/on will wreak massive havoc. Yes, that even
applies to state only used in ->mode_set callbacks, since we need to
call those even for dpms on when the Haswell power well cleared
everything out.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So on a bunch of setups we only have 2 fdi lanes available, e.g. hsw
VGA or 3 pipes on ivb. And seemingly a lot of modes don't quite fit
into this, among them the default 1080p mode.
The solution is to dither down the pipe a bit so that everything fits,
which this patch implements.
But ports compute their state under the assumption that the bpp they
pick will be the one selected, e.g. the display port bw computations
won't work otherwise. Now we could adjust our code to again up-dither
to the computed DP link parameters, but that's pointless.
So instead when the pipe needs to adjust parameters we need to retry
the pipe_config computation at the encoder stage. Furthermore we need
to inform encoders that they should not increase bandwidth
requirements if possible. This is required for the hdmi code, which
prefers the pipe to up-dither to either of the two possible hdmi bpc
values.
LVDS has a similar requirement, although that's probably only
theoretical in nature: It's unlikely that we'll ever see an 8bpc
high-res lvds panel (which is required to hit the 2 fdi lane limit).
eDP is the only thing which could increase the pipe_bpp setting again,
even when in the retry-loop. This could hit the WARN. Two reasons for
not bothering:
- On many eDP panels we'll get a black screen if the bpp settings
don't match vbt. So failing the modeset is the right thing to do.
But since that also means it's the only way to light up the panel,
it should work. So we shouldn't be able to hit this WARN.
- There are still opens around the eDP panel handling, and maybe we
need additional tricks. Before that happens it's imo no use trying
to be too clever.
Worst case we just need to kill that WARN or maybe fail the compute
config stage if the eDP connector can't get the bpp setting it wants.
And since this can only happen with an fdi link in between and so for
pch eDP panels it's rather unlikely to blow up, if ever.
v2: Rebased on top of a bikeshed from Paulo.
v3: Improve commit message around eDP handling with the stuff
things with Imre.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And also move the computed m_n values into the pipe_config. This is a
prep step to move the fdi state computation completely into the
prepare phase of the modeset sequence. Which will allow us to handle
fdi link bw constraints in a better way.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for two reasons:
- Correct handling of shared fdi lanes on ivb with fastboot.
- Handling fdi link bw limits when we only have two fdi lanes by
dithering down a bit.
Just search&replace in this patch, no functional change at all.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And put the pfit stuff into substructs while we're at it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This gets the panel fitter working on eDP on VLV, and should also apply
to eDP panels on G4x chipsets (if we ever detect and mark an all-in-one
panel as eDP anyway).
A few cleanups are still possible on top of this, for example the LVDS
border control could be placed in the LVDS encoder structure and updated
based on the result of the panel fitter calculation.
Multi-pipe fitting isn't handled correctly either if we ever get a config
that wants to try the panel fitter on more than one output at a time.
v2: use pipe_config for storing pfit values (Daniel)
add i9xx_pfit_enable function for use by 9xx and VLV (Daniel)
v3: fixup conflicts and lvds_dither check
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: fix up botched conflict resolution from Jesse:
- border = LVDS_BORDER_ENABLE was lost for CENTER scaling
- comment about gen2/3 panel fitter scaling was lost
- dev_priv->lvds_dither reintroduced.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up to now we've relied on the bios to get this right for us. Let's try
out whether our code has improved a bit, since we should dither
always when the output bpp doesn't match the plane bpp.
- gen5+ should be fine, since we only use the bios hint as an upgrade.
- gen4 changes, since here dithering is still controlled in the lvds
register.
- gen2/3 has implicit dithering depeding upon whether you use 2 or 3
lvds pairs (which makes sense, since it only supports 8bpc pipe
outpu configurations).
- hsw doesn't support lvds.
v2: Remove redudant dither setting.
v3: Completly drop reliance on dev_priv->lvds_dither.
v4: Enable dithering on gen2/3 only when we have a 18bpp panel, since
up-dithering to a 24bpp panel is not supported by the hw. Spotted by
Ville.
v5: Also only enable lvds port dithering on gen4 for 18bpp modes. In
practice this only excludes dithering a 10bpc plane down for a 24bpp
lvds panel. Not something we truly care about. Again noticed by Ville.
v6: Actually git add.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation of adding locking to backlight, make max backlight value
(the modulation frequency the PWM duty cycle value must not exceed)
internal to intel_panel.c.
Have intel_panel_set_backlight() accept a caller defined range for level,
and scale input to max backlight value internally.
Clean up intel_panel_get_max_backlight() and usage internally.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows unifying a bunch of the PLL calculations and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Valleyview voltage swing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric. Update
vlv_update_pll, i9xx_crtc_enable, and intel_enable_pll with the
appropriate programming.
We need to make sure that the tx lane reset occurs in both the full mode
set and DPMS paths, so factor things out to allow that.
v2: use different DPIO_DIVISOR values for VGA and DisplayPort
v3: Fix update pll logic to use same DPIO_DIVISOR & DPIO_REFSFR values
for all display interfaces
v4: collapse with various updates
v5: squash with crtc enable/pll enable bits
v6: split out DP code (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
remove unneeded check in 9xx pll div update (Jani)
wrap VLV pll update call in IS_VALLEYVIEW (Jani)
move port enable back to end of crtc enable (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
v7: fix up conflicts against latest drm-intel-next-queued
v8: use DPIO reg names, fix pipes (Jani)
from mPhy_registers_VLV2_ww20p5 doc
v9: update to latest info from driver enabling notes doc
driver_vbios_notes_9
v10: fixup a bit of pipe/port confusion to allow eDP and HDMI to work
simultaneously (Jesse)
v11: use pll/port callbacks for DPIO port activity (Daniel)
use separate VLV CRTC enable function (Daniel)
move around port ready checks (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop pfit changes and add a little comment explaining that
vlv has a different enable sequence and so needs it's own crtc_enable
callback. Also apply a fixup patch from Wu Fengguang to shut up some
compiler warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Program few Tx buffer Swing control settings through DPIO.
v2: fix up codingstyle (Daniel)
call from set_signal_levels (Ville, Daniel)
use proper port numbers (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Yogesh M <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2 changes)
[danvet: Reorder if-ladder to avoid two IS_VLV checks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
->disable and other modeset callbacks.
In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.
v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When an encoder is shared on several connectors there is only
one hotplug line, thus this line needs to be shared among these
connectors.
If HPD detect only works reliably on a subset of those connectors,
we want to poll the others. Thus we need to make sure that storm
detection doesn't mess up the settings for those connectors.
Therefore we store the settings in the intel_connector struct and
restore them from there.
If nothing is set but the encoder has a hpd_pin set we assume this
connector is hotplug capable.
On init/reset we make sure the polled state of the connectors
is (re)set to the default value, the HPD interrupts are marked
enabled.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It returns true if we've requested to turn the power well on and it's
really on. It also returns true for all the previous gens.
For now there's just one caller, but I'm going to add more.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clock computations and handling are highly encoder specific, both in
the optimal clock selection and also in which clocks to use and when
sharing of clocks is possible.
So the best place to do this is somewhere in the encoders, with a
generic fallback for those encoders without special needs. To facility
this, add a pipe_config->clocks_set boolean.
This patch here is only prep work, it simply sets the computed clock
values in pipe_config->dpll, and uses that data in the hw clock
setting functions.
Haswell code isn't touched, simply because Haswell clocks work much
different and need their own infrastructure (with probably a
Haswell-specific config->ddi_clock substruct).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes noticed in his review of my DP cleanup series that
intel_edp_target_clock is now unused. Checking related code I've
noticed that also intel_edp_link_config is long unused.
Kill them both.
Wrt leaky eDP functions used in the common crtc code, the only thing
still left is intel_encoder_is_pch_edp. That one is just due to the
massive confusion between eDP vs. DP and port A vs. port D. Crtc code
should at most concern itself with the later, never with the former.
But that's material for another patch series.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need it in the fdi m_n computation, which nicely kills almost
all ugly special cases in there.
It looks like we also need this to handle 12bpc hdmi correctly.
Eventually it might be better to switch things around and put the
target clock into adjusted_mode->clock and create a new pipe_config
parameter for the port link clock.
v2: Add a massive comment in the code to explain this mess.
v3: s/dp_target_clock/pixel_target_clock in anticipation of the hdmi
use-case.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a flag to designate dp encoders and the dp link m_n parameters
in the pipe config for that. And now that the pipe bpp computations
have been moved up and stored in the pipe config, too, we can do this
without losing our sanity.
v2: Rebased on top of Takashi Iwai's fix to (again) fix the target
clock handling for eDP. Luckily the new code is sane enough and just
does the right thing!
v3: Move ->has_dp_encoder to this patch (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's a rather decent confusion going on around transcoder m_n
values. So let's clarify:
- All dp encoders need this, either on the pch transcoder if it's a
pch port, or on the cpu transcoder/pipe if it's a cpu port.
- fdi links need to have the right m_n values for the fdi link set in
the cpu transcoder.
To handle the pch vs transcoder stuff a bit better, extract transcoder
set_m_n helpers. To make them simpler, set intel_crtc->cpu_transcoder
als in ironlake_crtc_mode_set, so that gen5+ (where the cpu m_n
registers are all at the same offset) can use it.
Haswell modeset is decently confused about dp vs. edp vs. fdi. dp vs.
edp works exactly the same as dp (since there's no pch dp any more),
so use that as a check. And only set up the fdi m_n values if we
really have a pch encoder present (which means we have a VGA encoder).
On ilk+ we've called ironlake_set_m_n both for cpu_edp and for pch
encoders. Now that dp_set_m_n handles all dp links (thanks to the
pch encoder check), we can ditch the cpu_edp stuff from the
fdi_set_m_n function.
Since the dp_m_n values are not readily available, we need to
carefully coax the edp values out of the encoder. Hence we can't (yet)
kill this superflous complexity.
v2: Rebase on top of the ivb fdi B/C check patch - we need to properly
clear intel_crtc->fdi_lane, otherwise those checks will misfire.
v3: Rebased on top of a s/IS_HASWELL/HAS_DDI/ patch from Paulo Zanoni.
v4: Drop the addition of has_dp_encoder, it's in the wrong patch (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No constant alpha yet though, that needs a new ioctl and/or property to
get/set.
v2: use drm_plane_format_cpp (Ville)
fix up vlv_disable_plane, remove IVB bits (Ville)
remove error path rework (Ville)
fix component order confusion (Ville)
clean up platform init (Ville)
use compute_offset_xtiled (Ville)
v3: fix up more format confusion (Ville)
update to new page offset function (Ville)
v4: remove incorrect formats from framebuffer_init (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Thomas Gleixner spotted, it's rather horrible racy:
- We can miss almost a full tick, so need to compensate by 1 jiffy.
- We need to re-check the condition when having timed-out, since a
the last check could have been before the timeout expired. E.g. when
we've been preempted or a long irq happened.
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Jack Winter <jbh@alchemy.lu>
Cc: Jack Winter <jbh@alchemy.lu>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit bcf9dcc1e6
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jul 15 09:42:38 2012 +0100
drm/i915: Workaround hang with BSD and forcewake on SandyBridge
and
commit 0cc2764cc4
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Sat Sep 1 22:59:48 2012 -0700
drm/i915: use cpu_relax() in wait_for_atomic
these two macros are essentially the same, so unify them. We keep the
_us version since it's a nice documentation for smaller timeouts.
v2: Fixup time unit conversion, _wait_for takes ms (Ville).
Cc: Jack Winter <jbh@alchemy.lu>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The old code only handled either 6bpc or 8bpc. Since it's easy to do,
reorganize the code to be a bit more generic so that it can also handle
10bpc and 12bpc. Note that we still start with 8bpc, so there's no
functional change.
Also, since we no don't need to compute the 6BPC flag in the mode_valid
callback, we can consolidate things a bit. That requires though that
the link bw computation is moved up in the compute_config callback.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to compute this earlier. To avoid a big complicated patch,
this patch here just does the big search&replace and still calls the
old functions at the same places.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have a useful struct for this, let's use it. Some neat
pointer-chasing required, but it's all there already.
v2: Rebased on top of the added Haswell limited color range support.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is used way too often in the enable/disable paths. And will
be even more useful in the future.
Note that correct semantics of this change highly depend upon
correct updating of intel_crtc->config: Like with all other
modeset state, we need to call ->disable with the old config,
but ->mode_set and ->enable with the new config.
v2: Do not yet use the flag in the ->disable callbacks - atm we don't
yet have support for the information stored in the pipe_config in the
hw state readout code, so this will be wrong at boot-up/resume.
v3: Rebased on top of the hdmi/dp ddi encoder merging.
v4: Fixup stupid rebase error which lead to a NULL vfunc deref.
v5: On haswell the VGA port is on the PCH!
v6: s/IS_HASWELL/HAS_DDI/, spotted by Paulo Zanoni. Also add a missing
parameter name in a function declaration.
v7: Don't forget to git add ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Used by SDVO (and hopefully, eventually HDMI, if we ever get around
to fixing up the low dotclock CEA modes ...).
This required adding a new encoder->mode_set callback to be able to
pass around the intel_crtc_config.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only used by the lvds encoder. Note that we shouldn't do the same
simple conversion with the FORCE_6BPC flag, since that's much better
handled by moving all the pipe_bpc computation around.
This requires that we pass the pipe config around to encoders, so
that they can set special attributes and set constraints. To do so
introduce a new ->compute_config encoder callback, which is called in
stead of the drm crtc helper's ->mode_fixup.
To avoid massive churn all over the codebase we don't want to convert
all existing ->mode_fixup functions. Instead I've opted to convert
them on an as-needed basis (mostly to cut down on rebase conflicts and
to have more freedom to experiment around while developing the
patches).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently only containing the requested and the adjusted mode. And
only crtc callbacks are converted somewhat to it, encoders will be
done on a as-needed basis (simply too much churn in one patch
otherwise).
Future patches will add tons more useful stuff to this struct,
starting with the very simple.
v2: Store the pipe_config in the intel_crtc, so that the ->mode-set,
->enable and also ->disable have easy access to it.
v3: Store the pipe config in the right crtc ...
v4: Rebased.
v5: Fixup an OOPS when trying to kfree an ERR_PTR.
v6: Used drm_moode_copy and some other small cleanups as suggested
by Ville Syrjälä.
v7: drm_mode_copy preserves the mode id of the destination, so no need
to clear it again (Ville).
v8: Break a long line spotted by Paulo.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To clean up hotplug support we add a new enum to intel_encoder:
enum hpd_pin. It allows the encoder to request a hpd line but leave
the details which IRQ is responsible on which chipset generation
to i915_irq.c.
This way requesting hotplug support will become really simple on
the encoder/connector level.
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be used to restore sprite state on resume.
v2: move sprite tracking bits up so we don't track modified sprite state
v3: use src_x/y in sprite suspend/resume code (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are really talking about the transcoder function here and the disable
version uses trancoder in its name already, so let's try to be
consistent.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two regressions fixes from snowboarding land
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Revert hdmi HDP pin checks
drm/i915: Handle untiled planes when computing their offsets
We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.
However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.
Fixes regression from commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's my promised pile of fixes for 3.9. I've dropped the core prep
patches for vt-switchless suspend/resume as discussed on irc. Highlights:
- Fix dmar on g4x. Not really gfx related, but I'm fed up with getting
blamed for dmar crapouts.
- Disable wc ptes updates on ilk when dmar is enabled (Chris). So again,
dmar, but this time gfx related :(
- Reduced range support for hsw, using the pipe CSC (Ville).
- Fixup pll limits for gen3/4 (Patrick Jakobsson). The sdvo patch is
already confirmed to fix 2 bug reports, so added cc: stable on that one.
- Regression fix for 8bit fb console (Ville).
- Preserve lane reversal bits on DDI/FDI ports (Damien).
- Page flip vs. gpu hang fixes (Ville). Unfortuntely not quite all of
them, need to decide what to do with the currently still in-flight ones.
- Panel fitter regression fix from Mika Kuoppala (was accidentally left on
on some pipes with the new modset code since 3.7). This also improves
the modeset sequence and might help a few other unrelated issues with
lvds.
- Write backlight regs even harder ... another installement in our eternal
fight against the BIOS and backlights.
- Fixup lid notifier vs. suspend/resume races (Zhang Rui). Prep work for
new ACPI stuff, but closing the race itself seems worthwile on its own.
- A few other small fixes and tiny cleanups all over.
Lots of the patches are cc: stable since I've stalled on a few
not-so-important fixes for 3.8 due to the grumpy noise Linus made.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (33 commits)
intel/iommu: force writebuffer-flush quirk on Gen 4 Chipsets
drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK
drm/i915: Implement pipe CSC based limited range RGB output
drm/i915: inverted brightness quirk for Acer Aspire 4736Z
drm/i915: Print the hw context status is debugfs
drm/i915: Use HAS_L3_GPU_CACHE in i915_gem_l3_remap
drm/i915: Fix PIPE_CONTROL DW/QW write through global GTT on IVB+
drm/i915: Set i9xx sdvo clock limits according to specifications
drm/i915: Set i9xx lvds clock limits according to specifications
drm/i915: Preserve the DDI link reversal configuration
drm/i915: Preserve the FDI line reversal override bit on CPT
drm/i915: add missing \n to UTS_RELEASE in the error_state
drm: Use C8 instead of RGB332 when determining the format from depth/bpp
drm: Fill depth/bits_per_pixel for C8 format
drm/i915: don't clflush gem objects in stolen memory
drm/i915: Don't wait for page flips if there was GPU reset
drm/i915: Kill obj->pending_flip
drm/i915: Fix a typo in a intel_modeset_stage_output_state() comment
drm/i915: remove bogus mutex_unlock from error-path
drm/i915: Print the pipe control page GTT address
...
Some (but not all) of the HDMI registers can be used to control sDVO,
so those registers have two names. IMHO, when we're talking about
HDMI, we really should call the HDMI control register "hdmi_reg"
instead of "sdvox_reg", otherwise we'll just confuse people reading
our code (we now have platforms with HDMI but without SDVO). So now
"struct intel_hdmi" has a member called "hdmi_reg" instead of
"sdvox_reg".
Also, don't worry: "struct intel_sdvo" still has a member called
"sdvo_reg".
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can remove some duplicated code and avoid more mistakes
and regressions with these registers in the future.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GPU reset will drop all flips that are still in the ring. So after the
reset, call update_plane() for all CRTCs to make sure the primary
planes are scanning out from the correct buffer.
Also finish all pending flips. That means user space will get its
page flip events and won't get stuck waiting for them.
v2: Explicitly finish page flips instead of relying on FLIP_DONE
interrupt being generated by the base address update.
v3: Make two loops over crtcs to avoid deadlocks with the crtc mutex
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup long line complaint from checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
