The MCI can report the command status more finegrained, so, add more
status code defines and update the MCI_SUCCESS macro.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Split off all code specific to the MaxSX8 cards to a separate ddbridge-sx8
module and hook it up in the Makefile. This also adds evaluation of the
mci_type to allow for using different attach handling for different cards.
As different cards can implement things differently (ie. support differing
frontend_ops, and have different base structs being put ontop of the
common mci_base struct), this introduces the mci_cfg struct which is
initially used to hold a few specifics to the -sx8 submodule. While at it,
the handling of the i/q mode is adjusted slightly. Besides this and
handling mci_base and sx8_base struct pointers where needed, all code
is copied unmodified from ddbridge-mci.c.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation for splitting all MaxSX8 related code parts from the common
MCI code, prefix both mci_cmd() and mci_config() functions with ddb_,
remove the static marking and add matching function prototypes to
ddbridge-mci.h so these functions can be reused from other files within
the ddbridge driver. As this requires the mci-related structs to be
defined in ddbridge-mci.h, move struct mci and struct mci_base there and
clean them up.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For better support for future MCI based cards, rename the mci struct
member to mci_ports to carry the number of ports on the cards, and add a
mci_type member to identify the card type to handle differing hardware.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Recent FPGA firmware reports more data and values in sent command
responses. Adjust the mci_command and mci_result structs including it's
unions to match these changes and add a few comments explaining things.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adjustments to match the FPGA firmware, and the signal I/Q values are
reported as s16 types from the card firmware.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement querying signal statistics from the MCI and report this data
in read_status() as DVBv5 statistics.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Update the copyright year information in the MCI headers to 2017-2018.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Change the start of the MCI ID range (internally used only) to 48 and
define an ID for the SX8 card type. Use this new ID to handle device
attachment.
This change is done in preparation for support of more MCI based cards.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Throughout the function, dev->link[l] is used several times. Unclutter
this a bit by declaring a ddb_link var at the top of the function, assign
the address of dev->link[l] to it and use that var to access the link[]
struct member.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ddbridge has a few MDIO related remainders (defines, hwinfo struct) which
aren't of any use for the in-kernel driver at all (they're only used in
conjunction with the OctoNet SAT>IP boxes which the kernel driver doesn't
have any support for), so clean this up.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C_COMMAND response reports an error in the I2C bus communication
using bit 17. Evaluate the response more thoroughly and log an error
if an I2C problem was detected.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Devices supporting dummy tuner operation can exist on any link, not only
on link 0, so fix this accordingly.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In demod_attach_stv0910(), the LNBH25 IC is being blindly attached and,
if the result is bad, blindly attached on another possible I2C address.
The LNBH25 uses it's set_voltage function to test for the IC and will
print an error to the kernel log on failure. Prevent this by probing
the possible I2C address and use this (and only this) to attach the
LNBH25 I2C driver. This also allows the stv0910 attach function to be
a bit cleaner.
Picked up from the upstream dddvb GIT and adapted for the LNBH25 driver
variant from the kernel tree.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CineS2 V7(A) and Octopus CI S2 Pro/Advanced cards support faster TS speeds
on the card's contained stv0910 demodulator when their FPGA was updated
with a recent (>= 1.7, version number applies to all mentioned cards)
vendor firmware. Enable this faster TS speed on card port 0 (contained
demod) and parallel stv0910 connections when the card firmware is at least
1.7 or later.
Note: The mentioned cards and their demods are handled via the STV0910_PR
and STV0910_P tuner types. DuoFlex modules with such demodulators are
handled via the STV0910 (without suffix) types where such TS speed
increase doesn't technically make sense.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Tested-by: Helmut Auer <post@helmutauer.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a tsspeed config option to struct stv0910_cfg which can be used by
users of the driver to set the (parallel) TS speed (higher speeds enable
support for higher bitrate transponders). If tsspeed isn't set in the
config, it'll default to a sane value.
This commit also updates the two consumers of the stv0910 driver (ngene
and ddbridge) to have a default tsspeed in their stv0910_cfg templates.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Tested-by: Helmut Auer <post@helmutauer.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fixes two checkpatch warnings
WARNING: function definition argument 'xxx' should also have an identifier name
in the ddb_mci_attach() prototype definition. checkpatch keeps complaining
on the "int (**fn_set_input)" as it seems to have issues with the
ptr-to-ptr, though this probably needs fixing in checkpatch.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In stop(), an (unlikely) out-of-bounds write error can occur when setting
the demod_in_use element indexed by state->demod to zero, as state->demod
isn't checked for being in the range of the array size of demod_in_use, and
state->demod maybe carrying the magic 0xff (demod unused) value. Prevent
this by checking state->demod not exceeding the array size before setting
the element value. To make the code a bit easier to read, replace the magic
value and the number of array elements with defines, and use them at a few
more places.
Detected by CoverityScan, CID#1468550 ("Out-of-bounds write")
Thanks to Colin for reporting the problem and providing an initial patch.
Fixes: daeeb1319e ("media: ddbridge: initial support for MCI-based MaxSX8 cards")
Reported-by: Colin Ian King <colin.king@canonical.com>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The method dvb_frontend_ops::get_frontend_algo() is defined as
returning an 'enum dvbfe_algo', but the implementation in this
driver returns an 'int'.
Fix this by returning 'enum dvbfe_algo' on drivers.
[mchehab+samsung@kernel.org: merge similar patches and patch
ddbridge-mci.c the same way]
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Three really tiny minors in this single commit which all on their own
would just clutter up the commit history unnecessarily:
* ddbridge-regs.h is lacking an include guard. Add it.
* Fix an unnecessary NULL initialisation in ddbridge-ci. The declaration
of the ci struct ptr is immediately followed by kzalloc().
* Clarify that the CXD2099AR is a Sony device in the cxd2099 driver at a
few places including Kconfig.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set DDBRIDGE_VERSION in ddbridge.h to 0.9.33-integrated to reflect the
updated driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add needed logic into dvb_input_attach(), ddb_port_probe() and
ddb_ports_init() to initialize and support these new cards.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add PCI IDs and ddb_info for the new MCI-based MaxSX8 cards. Also add
needed defines so the cards can be hooked up into ddbridge's probe and
attach handling.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement frontend attachment as ddb_fe_attach_mci() into the
ddbridge-max module. The MaxSX8 MCI cards are part of the Max card series
and make use of the LNB controller driven by the already existing lnb
functionality, so here's where this code belongs to.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds initial support for the new MCI-based (micro-code interface)
DD cards, with the first one being the MaxSX8 eight-tuner DVB-S/S2/S2X
PCIe card. The MCI is basically a generalized interface implemented in
the card's FPGA firmware and usable for all kind of cards, without the
need to implement any demod/tuner drivers as this interface "hides" any
I2C interface to the actual ICs, in other words any required driver is
implemented in the card firmware.
At this stage, the MCI interface is quite rudimentary with things like
signal statistics reporting missing, but is already working to serve
DVB streams to DVB applications. Missing functionality will be enabled
over time.
This implements only the ddbridge-mci sub-object and hooks it up to the
Makefile so the object gets build. The upcoming commits hook this module
into all other ddbridge parts where required, including device IDs etc.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Octopus V3 and Octopus Mini devices support set up of a dummy tuner
mode on port 0 that will deliver a continuous data stream of 125MBytes
per second while raising IRQs and filling the DMA buffers, which comes
handy for some stress, PCIe link and IRQ handling testing. The dummy
frontend is registered using dvb_dummy_fe's QAM dummy frontend. Set
ddbridge.dummy_tuner to 1 to enable this on the supported cards.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the number of DMA buffers and their size configurable using module
parameters. Being able to set these to a higher number might help on
busy systems when handling overall high data rates without having to
edit the driver sources and recompile things.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, /sys/class/ddbridgeX/devid always reports 0 due to devid not
being set at all. Set the devid field alongside while storing all other
hardware ID data.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A 188 byte gap has to be left between the writer and the consumer. This
requires 2*188 bytes available to be able to write to the output buffers.
So, change ddb_output_free() to report free bytes according to this rule.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure to save IRQ states before taking the dma lock, as already done
in it's input_work() counterpart.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Improve IRQ handling in the separated MSG/I2C and IO/TSDATA handlers by
applying a mask for recognized bits immediately upon reading the IRQ mask
from the hardware, so only the bits/IRQs that actually were set will be
acked.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, each IRQ requires one IRQ_HANDLE() line to call each IRQ
handler that was set up. Add a IRQ_HANDLE_NIBBLE() and IRQ_HANDLE_BYTE()
macro to call all handlers in blocks of four (_NIBBLE) or eight (_BYTE)
handlers at a time, to make this construct more compact.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce the ddb_irq_set() helper function (along with a matching
prototype in ddbridge.h) to improve the set up of the IRQ handlers
and handler_data, and rework storing this data into the ddb_link
using a new ddb_irq struct. This also does the necessary rework
of affected variables. And while at it, always do queue_work in
input_handler() as there's not much of a difference to directly
calling input_work if there's no ptr at input->redi, or queueing
this call.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of trying to manage IRQ numbers on itself, utilise the
pci_irq_vector() function to do this, which will take care of correct IRQ
numbering for MSI and non-MSI IRQs. While at it, request and enable MSI-X
interrupts for hardware (boards and cards) that support this.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce the ddb_msi_exit() helper to be used for cleaning up previously
allocated MSI IRQ vectors. Deduplicates code and makes things look
cleaner as for all cleanup work the CONFIG_PCI_MSI ifdeffery is only
needed in the helper now. Also, replace the call to the deprecated
pci_disable_msi() function with pci_free_irq_vectors().
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the ddbridge module initialisation and cleanup code to ddbridge-core
and set up the ddb_wq workqueue there, and create and destroy the ddb
device class there aswell. Due to this, the prototypes for ddb_wq,
ddb_class_create() and ddb_class_destroy() aren't required in ddbridge.h
anymore, so remove them. Also, declare ddb_wq and the ddb_class_*()
functions static.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Besides the 'msi' module option, all options are used from within
ddbridge-core only, so move them over from ddbridge-main, and declare the
associated variables static. Since the prototypes in ddbridge.h aren't
necessary anymore now, remove them. As a side effect, this has the benefit
of aligning things more with the dddvb upstream.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The check for a valid ptr in ddb_io->dma isn't really necessary since only
devices that do data transport using DMA are supported by the driver, and
all previous initialisation code (through input_init(), output_init() and
dma_init(), has_dma is always true as it's set in ddb_probe() during
driver load) guarantees the ptr is set.
As a side effect, this silences these sparse warnings (albeit them being
false positives as ddb_io->dma won't change in these functions so the
condition always equals to the same result):
drivers/media/pci/ddbridge/ddbridge-core.c:495:9: warning: context imbalance in 'ddb_output_start' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:510:9: warning: context imbalance in 'ddb_output_stop' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:525:9: warning: context imbalance in 'ddb_input_stop' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:560:9: warning: context imbalance in 'ddb_input_start' - different lock contexts for basic block
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of keeping duplicated I2C client handling construct, make use of
the newly introduced dvb_module_*() helpers. This not only keeps things
way cleaner and removes the need for duplicated I2C client attach code,
but even allows to get rid of some variables that won't help in making
things look cleaner anymore.
The check on a valid ptr on port->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the way the cxd2099 hardware is being attached to the new I2C
client interface way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the TODO file, this driver only landed in staging because of
the way device nodes and data transfers are handled. Besides that this way
(use of secX devices) has become sort of standard to date (ie. VDR
supports this literally since ages via the ddci plugin, TVHeadend received
this functionality lately, and minisatip being currently worked on
regarding this), most importantly this I2C client only driver isn't even
responsible for setting up device nodes, not for handling data
transfer and so on, but only serves as interface for the dvb_ca_en50221
subsystem, just like every other DVB card out in the wild, with hard-wired
or such flexible CA interfaces. And, it would even work with cards having
the cxd2099 controller hard-wired.
Also, this driver received quite some love and even is a proper I2C client
driver by now. So, as this driver acts as a EN50221 frontend device, move
it to dvb-frontends. There is no need to keep it buried in staging.
This commit also updates all affected Kconfig and Makefile's, and adds
MEDIA_AUTOSELECT depends to ddbridge and ngene.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Deduplicate the checks for a valid ptr in port->en, and also handle the
default case to also catch eventually yet unsupported CI hardware.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
Move the CI teardown code to ddbridge-ci.c where everything else related
to CI hardware lives.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As all error handling improved quite a bit, don't stop attaching frontends
if one of them failed, since - if other tuner modules are connected to
the PCIe bridge - other hardware may just work, so don't break on a single
port failure, but rather initialise as much as possible. Ie. if there are
issues with a C2T2-equipped PCIe bridge card which has additional DuoFlex
modules connected and the bridge generally works, the DuoFlex tuners can
still work fine.
If all ports failed to initialise where connected hardware was detected on
at first, return -ENODEV though to cause this PCI device to fail and free
all allocated resources. In any case, leave a kernel log warning (or
error, even) if things went wrong.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In ddb_ports_attach(), if the second input of a dual tuner failed to
initialise, the first one can be detached (and resources be freed) as
this will be counted as the whole port having failed to initialise,
thus the first one won't be used anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In ddb_init(), the deinitialization sequence isn't correct when handling
errors, and could even lead to a memleak depending on where things failed.
Fix the deinit order.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All CI types do dvb_ca_en50221_init() with the same arguments. Move this
call after the switch-case to remove the repetition in every case block.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
