Sort headers alphabetically - it helps locating duplicates, and makes it
easier to figure out where to insert new headers. Alphabetic order should
also prove that each header is self-contained, i.e. can be included without
prerequisites.
Link: https://lore.kernel.org/r/20230202144628.14443-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
Fixes: 5390a8df76 ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Reported-by: Alexander Stein <Alexander.Stein@tq-group.com>
Signed-off-by: Louis Rannou <lrannou@baylibre.com>
Tested-by: Alexander Stein <Alexander.Stein@tq-group.com>
Link: https://lore.kernel.org/r/20230203070754.50677-1-tudor.ambarus@linaro.org
[ta: refine changes, new commit message, fix compilation error]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The INFO() macro defines an ID array and a couple of geometry
properties. Right now all its lines are duplicated twice because of the
INFO6() macro (for extended IDs) and soon as well we will need to add a
geometry parameter to include the number of banks.
In order to limit the code duplication, let's create a number of
intermediate macros which will facilitate defining high-level INFOX()
macros.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221215081241.407098-2-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Cypress defines two flavors of configuration registers, volatile and
non volatile, and both use the same bit fields. Rename the bitfields in
the configuration registers so that they can be used for both flavors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Link: https://lore.kernel.org/linux-mtd/20230110164703.83413-2-tudor.ambarus@linaro.org
CFR5[6] is reserved bit and must be always 1. Set it to comply with flash
requirements. While fixing SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_{EN, DS}
definition, stop using magic numbers and describe the missing bit fields
in CFR5 register. This is useful for both readability and future possible
addition of Octal STR mode support.
Fixes: c3266af101 ("mtd: spi-nor: spansion: add support for Cypress Semper flash")
Cc: stable@vger.kernel.org
Reported-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Tested-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/linux-mtd/20230110164703.83413-1-tudor.ambarus@linaro.org
spi-nor/core.c needs to include linux/delay.h,
or it would raise below compile warning:
drivers/mtd/spi-nor/core.c: In function ‘spi_nor_soft_reset’:
drivers/mtd/spi-nor/core.c:2779:2: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
2779 | usleep_range(SPI_NOR_SRST_SLEEP_MIN, SPI_NOR_SRST_SLEEP_MAX);
| ^~~~~~~~~~~~
Fixes: d73ee7534c ("mtd: spi-nor: core: perform a Soft Reset on shutdown")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20220923031457.56103-1-zengheng4@huawei.com
BFPT_DWORD() converts 1-based indexing to 0-based indexing for C arrays,
and is used in BFPT parse. Per JESD216F.02, the conversion is applicable
to other parameter tables than BFPT. This patch renames the macro to
SFDP_DWORD() so that we can use it for other parameter tables than BFPT.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/e42feac840fe3a31187419e91b2d514d9f259d15.1672026365.git.Takahiro.Kuwano@infineon.com
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmOJ59AACgkQS1VPR6WN
FOnzOQf/WLBTNFtPcJoS7cdjlh4fuGySDUKuLifOX+Tmk/ki3XFCZR98cESgb5m+
hCyFDeER/qfdOK9ObT3K1GBS6x7zx8YkskbucjAU0vlIsr2ZHCjNpNiAHrADsKjR
579N0Xwh2ibh7uVJ1xvsPwObdAc8P/tjGHHWF6hGEZzIPYXJVce+qDktkkLfbZ/P
Fik6+y3h68wW/0kDNt/gNmNcb5Z3fjxySs21Np5sy7bUtVVBjHWLo0OpjNadDH9M
m6AkhFA5h9OVl5E4jHBpxc4NvlAa5f6520vESpieseNJiIMWo0W/eSkVsframFew
ILdtXCHjkbS6kgvSpUViobMFsgCjaA==
=Yi2q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.2' into mtd/next
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Fix merge conflict in the jedec,spi-nor bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SFDP table of some flash chips do not advertise support of Quad Input
Page Program even though it has support. Use flags and add hardware
cap for these chips.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: move pp setting in spi_nor_init_default_params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-2-sudip.mukherjee@sifive.com
The datasheet of is25wp256 says it supports SFDP. Get rid of the static
initialization of the flash parameters and init them when parsing SFDP.
Testing showed the flash using SPINOR_OP_READ_1_1_4_4B 0x6c,
SPINOR_OP_PP_4B 0x12 and SPINOR_OP_BE_4K_4B 0x21 before enabling SFDP.
After this patch, it parses the SFDP information and still uses the
same opcodes.
Set sector_size and n_sectors to zero as they will be discovered when
parsing SFDP.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: set sector_size and n_sectors to zero]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-1-sudip.mukherjee@sifive.com
The number of bytes used by spi_nor_spimem_check_readop() may be
incorrect for the dummy cycles. Since nor->read_dummy is not initialized
before spi_nor_spimem_adjust_hwcaps().
We use both mode and wait state clock cycles instead of nor->read_dummy.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Co-developed-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221031124633.13189-1-allen-kh.cheng@mediatek.com
When utilizing PARSE_SFDP to initialize the flash parameter, the
deprecated initializing method spi_nor_init_params_deprecated() and the
function spi_nor_manufacturer_init_params() within it will never be
executed, which results in the default_init hook function will also never
be executed.
This is okay for 'D' generation of GD25Q256, because 'D' generation is
implementing the JESD216B standards, it has QER field defined in BFPT,
parsing the SFDP can properly set the quad_enable function. The 'E'
generation also implements the JESD216B standards, and it has the same
status register definitions as 'D' generation, parsing the SFDP to set
the quad_enable function should also work for 'E' generation.
However, the same thing can't apply to 'C' generation. 'C' generation
'GD25Q256C' implements the JESD216 standards, and it doesn't have the
QER field defined in BFPT, since it does have QE bit in status register
1, the quad_enable hook needs to be tweaked to properly set the
quad_enable function, this can be done in post_bfpt fixup hook.
Fixes: 047275f7de ("mtd: spi-nor: gigadevice: gd25q256: Init flash based on SFDP")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yaliang Wang <Yaliang.Wang@windriver.com>
[tudor.ambarus@microchip.com: Update comment in gd25q256_post_bfpt]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221016171901.1483542-2-yaliang.wang@windriver.com
It doesn't make sense to put "set" on its own line like that.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221101162906.990125-1-j.neuschaefer@gmx.net
We don't have a database entry for the generic SPI-NOR flash driver and
thus we don't have a JEDEC ID to print. Print the (cached) JEDEC ID
instead.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-8-michael@walle.cc
Our SFDP parsing is everything we need to support all basic operations
of a flash device. If the flash isn't found in our in-kernel flash
database, gracefully fall back to a driver described solely by its SFDP
tables.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-7-michael@walle.cc
4bait will set the erase size to 0 if there is no corresponding
opcode for the 4byte erase. Fix spi_nor_select_uniform_erase to skip
the 0 erase size to avoid mtd device registration failure cases.
Reported-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-6-michael@walle.cc
sfdp.h should only contain constants related to the JEDEC SFDP
specification(s).
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-5-michael@walle.cc
At the moment, we print the JEDEC ID that is stored in our database. The
generic flash support won't have such an entry in our database. To find
out the JEDEC ID later we will have to cache it. There is also another
advantage: If the flash is found in the database, the ID could be
truncated because the ID of the entry is used which can be shorter. Some
flashes still holds valuable information in the bytes after the JEDEC ID
and come in handy during debugging of when coping with INFO6() entries.
These are not accessible for now.
Save a copy of the ID bytes after reading and display it via debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-4-michael@walle.cc
The manufacturer may be optional when pure SFDP flashes are supported.
Hide the sysfs property if no manufacturer is set.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-3-michael@walle.cc
Some non-jedec compliant flashes (like the Everspin flashes) don't have
an ID at all. Hide the attribute in this case.
Fixes: 36ac022862 ("mtd: spi-nor: add initial sysfs support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-2-michael@walle.cc
Erase can be zeroed in spi_nor_parse_4bait() or
spi_nor_init_non_uniform_erase_map(). In practice it happened with
mt25qu256a, which supports 4K, 32K, 64K erases with 3b address commands,
but only 4K and 64K erase with 4b address commands.
Fixes: dc92843159 ("mtd: spi-nor: fix erase_type array to indicate current map conf")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211119081412.29732-1-alexander.sverdlin@nokia.com
Add an error message when failing to exit the 4-byte address mode. Do not
stop the execution and go through the spi_nor_soft_reset() method if used,
in the hope that the flash will default to 3-byte address mode after the
reset.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220728030159.68680-1-tudor.ambarus@microchip.com
We track in the core the internal address mode of the flash. Stop using
hardcoded values for the number of bytes of address and use
nor->addr_nbytes and nor->params->addr_mode_nbytes instead.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220728041451.85559-3-tudor.ambarus@microchip.com
We track in the core the internal address mode of the flash. Stop using
hardcoded values for the number of bytes of address and use
nor->addr_nbytes and nor->params->addr_mode_nbytes instead.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220728041451.85559-2-tudor.ambarus@microchip.com
Read, Page Program, and Sector Erase settings are done in SFDP so we can
remove NO_SFDP_FLAGS from s28hs512t info. Since the default_init() is no
longer called after removing NO_SFDP_FLAGS, the initialization in the
default_init() is moved to late_init().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/12e468992f5d0cbd474abff3203100cc8163d4e5.1661915569.git.Takahiro.Kuwano@infineon.com
Add support for spi-nor flash reset via GPIO controller by reading the
reset-gpio property. If there is a valid GPIO specifier then reset will
be performed by asserting and deasserting the GPIO using gpiod APIs
otherwise it will not perform any operation.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220908064428.2962-3-sai.krishna.potthuri@amd.com
The Intel SPI-NOR controller does not support the 4-byte address opcode
so ->set_4byte_addr_mode() ends up returning -ENOTSUPP and the SPI flash
chip probe fail like this:
[ 12.291082] spi-nor: probe of spi0.0 failed with error -524
Whereas previously before commit 08412e72af ("mtd: spi-nor: core:
Return error code from set_4byte_addr_mode()") it worked just fine.
Fix this by ignoring -ENOTSUPP in spi_nor_init().
Fixes: 08412e72af ("mtd: spi-nor: core: Return error code from set_4byte_addr_mode()")
Cc: stable@vger.kernel.org
Reported-by: Hongyu Ning <hongyu.ning@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220923093441.3178-1-mika.westerberg@linux.intel.com
For erase operations, reg_proto must be used as indicated in
struct spi_nor description in spi-nor.h.
This issue was found when DT property spi-tx-bus-width is set to 4.
In this case the spi_mem_op->addr.buswidth is set to 4 for erase command
which is not correct.
Tested on stm32mp157c-ev1 board with mx66l51235f spi-nor.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
[ta: use nor->reg_proto in spi_nor_controller_ops_erase()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220629133013.3382393-1-patrice.chotard@foss.st.com
The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
These Infineon chips support volatile version of configuration registers
and it is recommended to update volatile registers in the field application
due to a risk of the non-volatile registers corruption by power interrupt.
Add support for volatile QE bit.
For the single-die package parts (512Mb and 1Gb), only bottom 4KB and
uniform sector sizes are supported. This is due to missing or incorrect
entries in SMPT. Fixup for other sector sizes configurations will be
followed up as needed.
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-8-tudor.ambarus@microchip.com
The page size check in s28hs512t fixup can be used for s25hs/hl-t as well.
Move that to a newly created local function.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-7-tudor.ambarus@microchip.com
We need to track the flash's internal address mode as there are flashes
that can operate with 4B opcodes but unfortunately do not have a 4B opcode
correspondent for all the 3B opcodes. Such an example is the Infineon
Semper chips which provide 4B opcodes for read/program/erase but do not
provide 4B opcodes for Read/Write Any Register. These registers are
indexed by address and require the internal address mode of the flash
before Read/Write Any Register opcodes are issued.
4B opcodes are preferred over changing the flash's address mode to 4byte,
as set_4byte_addr_mode could be done in a non-volatile way and could break
the boot sequence. Thus we need to track the flash's internal address mode
so that we can use 4B opcodes together with opcodes that don't have a 4B
opcode correspondent. Track flash's internal address mode.
addr_mode_nbytes is discovered when parsing BFPT. For the
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 case, one could introduce a method that
queries the flash's internal address mode at run-time (works for Winbond).
If a run-time querying can not be accomplished or if SFDP is not defined
at all, but the address mode is volatile and resets to a default known
value at boot, one can change the default addr_mode_nbytes value of 3 by
introducing a flash_info flag. If the address mode can not be queried,
discovered and it is configured via a non-volatile register, we may
introduce a dt property, but it will harm the generic approach of the
jedec,spi-nor compatible. All this complexity is not needed now, so let it
for future development.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-6-tudor.ambarus@microchip.com
The prams->set_4byte_addr_mode returns error code but is not handled
in spi_nor_init(). Handle the return code from set_4byte_addr_mode().
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-5-tudor.ambarus@microchip.com
At the SFDP parsing time we should not change members of struct spi_nor,
but instead fill members of struct spi_nor_flash_parameters which could
later on be used by callers. The caller will then decide if SFDP params
should be used and more importantly when they should be used. Clean the
code flow and don't initialize nor->addr_nbytes at SFDP parsing time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-4-tudor.ambarus@microchip.com
The maximum number of address bytes in SPI NOR is 4. Shrink the storage
size of the flash_info's addr_nbytes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-3-tudor.ambarus@microchip.com
Address width was an unfortunate name, as it means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR
framework.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-2-tudor.ambarus@microchip.com
The Intel SPI controller does not support low level operations, like
reading the flag status register (FSR). It only exposes a set of high
level operations for software to use. For this reason check the return
value of micron_st_nor_read_fsr() and if the operation was not
supported, use the status register value only. This allows the chip to
work even when attached to Intel SPI controller (there are such systems
out there).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220506105158.43613-1-mika.westerberg@linux.intel.com
The SECT_4K_PMC flag will set a device specific opcode for the 4k sector
erase. Instead of handling it in the core, we can move it to a
late_init(). In that late init, loop over all erase types, look for the
4k size and replace the opcode.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112650.2791459-1-michael@walle.cc
This is quite a quiet release but some new drivers mean that the
diffstat is fairly large, the new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLh9wACgkQJNaLcl1U
h9ApgAf/SvcHRyM06hw+00D2PAco7mxSiAs7rebxj4f0zPRNvUrYbUDWjakeKjoB
ocmpY6AW/vRBUM9xZsiQiLp/9NPltnVghZIBgp5gcS8zaXdxiZjZ68Z+uYp9SP9v
zj8F6bBQzk3lvuY+Cr1f68iXICA62Aa1yX28UFVLZkV0d+0AazpECZkb3hjOiL6P
0qSV6IfoFlJXYsyvAS4/MqYrHklSCD/0Ek09V9jPpZJPHn1ldbFs5zkstfs0PMc/
YeDlpStkjJE4OQ6+z6Ou/wGbcw11nWvKCSqF4bGRXLrgR/uIjOKomwOzaBUf/A6Q
AxQcKMtsBTx0VzYmwJwopj0qDvOq/A==
=6yj3
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The intention was to print the JEDEC ID in the following format:
nn nn nn
In this case format specifier has to be "%*ph". Fix it.
Fixes: 0257be79fc ("mtd: spi-nor: expose internal parameters via debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220512112027.3771734-1-michael@walle.cc
This patch allows accessing the upper 16m on the A variant (EN25QH256A) of
the EN25QH256 that shares same JEDEC ID.
Without this patch, addr_with is detected to be '4' but the read_opcode is
a plain READ (supporting only 3 byte addresses).
Setting PARSE_SFDP is enough to detect the read_opcode READ_4B on the A
variant. READ_4B is not available on the no-A variant.
Both variants support 4-byte address mode (spi_nor_set_4byte_addr_mode)
but that is prone to breaking on unexpected reboots if the reset pin isn't
connected (broken-flash-reset).
The no-A variant supports a 'high bank latch mode' that affects read,
program, and erase commands - similar to the extended address register
(EAR).
The HBL bit is manipulated using the ENHBL (0x67) and EXHBL (0x98)
opcodes.
Should it become necessary to distinguish the two variants in the future,
the A variant sets the SNOR_HWCAPS_READ_1_1_4 SFDP param - the no-A
variant doesn't.
Tested with and without fast read on the A variant only.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220502233310.791565-2-leon@georgemail.eu
