stk1160-v4l.c:478:49: warning: incorrect type in argument 3 (different base types)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by kbuild test robot:
drivers/media/usb/cx231xx/cx231xx-audio.c:445:16-20: ERROR: dev is NULL but dereferenced.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Unfortunately, on devices that have multiple interfaces, udev->dev
points to the parent device (usb) instead of the cx231xx specific one.
Due to that the logs don't look too nice, as they'll print messages
as if they were produced by USB core:
usb-1-2: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces
Instead of using the name of the parent device, let's use the name
of the first cx231xx interface for all cx231xx sub-modules.
With this path, the logs will be nicer:
cx231xx 1-2:1.1: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't need to show when it starts or stops. Just print lines
when devices are found.
After the changes, the output for i2c scan will be like:
usb 1-2: i2c scan: found device @ port 0 addr 0x40 [???]
usb 1-2: i2c scan: found device @ port 0 addr 0x60 [colibri]
usb 1-2: i2c scan: found device @ port 0 addr 0x88 [hammerhead]
usb 1-2: i2c scan: found device @ port 0 addr 0x98 [???]
usb 1-2: i2c scan: found device @ port 3 addr 0xa0 [eeprom]
usb 1-2: i2c scan: found device @ port 2 addr 0x60 [colibri]
usb 1-2: i2c scan: found device @ port 2 addr 0xc0 [tuner]
usb 1-2: i2c scan: found device @ port 4 addr 0x20 [demod]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we're using dev_foo, the logs become like:
usb 1-2: DVB: registering adapter 0 frontend 0 (Fujitsu mb86A20s)...
usb 1-2: Successfully loaded cx231xx-dvb
cx231xx: Cx231xx dvb Extension initialized
It is not clear, by the logs, that usb 1-2 name is an alias for
cx231xx. So, we also need to use dvb_info() at extension load/unload.
After the patch, it will print:
usb 1-2: Cx231xx dvb Extension initialized
With is coherent with the other logs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several places at cx231xx that uses printk without
any special reason. Change all of them to use dev_foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now cx231xx_i2c_check_for_device works like i2c_check_for_device of em28xx driver.
For me this fixes scanning of all ports but port 2.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are lots of debug printks printed with pr_info. Also, the
printk's data are not too coherent:
- there are duplicated driver name at the print format;
- function name format string differs from function to function;
- long strings broken into multiple lines;
- some printks just produce ugly reports, being almost useless
as-is.
Do a cleanup on that.
Still, there are much to be done in order to do a better printk
job on this driver, but, at least it will now be a way less
verbose, if debug printks are disabled, and some logs might
actually be useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
One of the identation blocks is wrong. Fix it.
While here, replace pr_info by pr_debug inside such block and
add the function name to the print messages, as otherwise they
will not help much.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It currently does just like what pr_foo() macros do. So,
replace them.
A deeper cleanup is needed, as there are lots of debug macros
printed with pr_info.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is a new version of the TechnoTrend CT2-4400 USB tuner. The difference is the demodulator that is used (Si2168-B40 instead of -A30).
For TT CT2-4400v2 a TS stream related parameter needs to be set, otherwise the stream becomes corrupted. The Windows driver for both CT2-4400 and CT2-4400v2 sets this as well. After this patch the driver works for both versions.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds control of the IF output level to the xc5000 tuner
configuration structure. Increases the IF level to the
demodulator to fix failure to lock and picture breakup
issues (with the au8522 demodulator, in the case of the
Hauppauge HVR950Q).
This patch works with all XC5000 firmware versions.
Signed-off-by: Richard Vollkommer <linux@hauppauge.com>
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Leadtek VC100 is a simple USB capture stick, similar to
Yakumo Movie Mixer.
Signed-off-by: Witold Krecicki <wpk+lkml@culm.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add an option to disable remote controller for DVBSky devices by specifying
the disable_rc option at modprobe.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dev_err includes the function name in the log printout, so there is no need to include it manually. While here, fix a small grammatical error in the i2c error message.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb-usb-v2 already prints out the MAC address, no need to print
it out also here.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The only remaining place that modifies the relevant bit is in function
cx231xx_set_Colibri_For_LowIF
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The scanning itself just fails (as before this series) but now
the correct busses are scanned.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All switching should be done by i2c mux adapters.
Drop explicit dont_use_port_3 flag.
Drop info message about switch.
Only the removed code in start_streaming is questionable:
It did switch the port_3 flag without accessing i2c in between.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I2C bus 1 has internally a switch. Use it as I2C_1_MUX_1 and
I2C_1_MUX_3, letting the I2C core handling the switch.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
change almost all instances of I2C_1 to I2C_1_MUX_3
Only these cases are changed to I2C_1_MUX_1:
* All that have dont_use_port_3 set.
* CX231XX_BOARD_HAUPPAUGE_EXETER, old code did explicitly not switch to port3.
* eeprom access for 930C
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Get used i2c port from bus_nr and status of port_3 switch.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is used later for is_tuner function that switches i2c behaviour for
some tuners.
[mchehab@osg.samsung.com: Fix CodingStyle on a multi-line comment]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preparation for mapping I2C_1_MUX_1 and I2C_1_MUX_3 later to the seperate
muxed i2c adapters.
Map mux adapters to I2C_1 for now.
Add local variables for i2c_adapters in dvb_init to get line lengths
shorter.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace numbers by the constants of same value and same meaning.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change to I2C_0 ... I2C_2 for the master ports
and add I2C_1_MUX_1 and I2C_1_MUX_3 for the muxed ones.
V2: Renamed mux adapters to seperate them from master adapters.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using the same name for all 3 i2c physical buses
inside cx231xx, name them differently, adding a number
to it. This helps to better deal with the logs.
[mchehab@osg.samsung.com: removed an unused bus_name var from
the original patch]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For each i2c master there is a i2c_client allocated that could be
deleted now that its only two users have been changed to use their
own i2c_client.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preparation for deleting the otherwise useless i2c_clients
that are allocated for all the i2c master adapters.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preparation for deleting the otherwise useless i2c_clients
that are allocated for all the i2c master adapters.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patches fixes an ancient bug in the dvb_usb_af9005 driver, which
has been reported at least in the following threads:
https://lkml.org/lkml/2009/2/4/350https://lkml.org/lkml/2014/9/18/558
If the driver is compiled in without any IR support (neither
DVB_USB_AF9005_REMOTE nor custom symbols), the symbol_request calls in
af9005_usb_module_init() return pointers != NULL although the IR
symbols are not available.
This leads to the following oops:
...
[ 8.529751] usbcore: registered new interface driver dvb_usb_af9005
[ 8.531584] BUG: unable to handle kernel paging request at 02e00000
[ 8.533385] IP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d
[ 8.535613] *pde = 00000000
[ 8.536416] Oops: 0000 [#1] PREEMPT PREEMPT DEBUG_PAGEALLOCDEBUG_PAGEALLOC
[ 8.537863] CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc6-00151-ga5c075c #1
[ 8.539827] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 8.541519] task: 89c9a670 ti: 89c9c000 task.ti: 89c9c000
[ 8.541519] EIP: 0060:[<7d9d67c6>] EFLAGS: 00010206 CPU: 0
[ 8.541519] EIP is at af9005_usb_module_init+0x6b/0x9d
[ 8.541519] EAX: 02e00000 EBX: 00000000 ECX: 00000006 EDX: 00000000
[ 8.541519] ESI: 00000000 EDI: 7da33ec8 EBP: 89c9df30 ESP: 89c9df2c
[ 8.541519] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[ 8.541519] CR0: 8005003b CR2: 02e00000 CR3: 05a54000 CR4: 00000690
[ 8.541519] Stack:
[ 8.541519] 7d9d675b 89c9df90 7d992a49 7d7d5914 89c9df4c 7be3a800 7d08c58c 8a4c3968
[ 8.541519] 89c9df80 7be3a966 00000192 00000006 00000006 7d7d3ff4 8a4c397a 00000200
[ 8.541519] 7d6b1280 8a4c3979 00000006 000009a6 7da32db8 b13eec81 00000006 000009a6
[ 8.541519] Call Trace:
[ 8.541519] [<7d9d675b>] ? ttusb2_driver_init+0x16/0x16
[ 8.541519] [<7d992a49>] do_one_initcall+0x77/0x106
[ 8.541519] [<7be3a800>] ? parameqn+0x2/0x35
[ 8.541519] [<7be3a966>] ? parse_args+0x113/0x25c
[ 8.541519] [<7d992bc2>] kernel_init_freeable+0xea/0x167
[ 8.541519] [<7cf01070>] kernel_init+0x8/0xb8
[ 8.541519] [<7cf27ec0>] ret_from_kernel_thread+0x20/0x30
[ 8.541519] [<7cf01068>] ? rest_init+0x10c/0x10c
[ 8.541519] Code: 08 c2 c7 05 44 ed f9 7d 00 00 e0 02 c7 05 40 ed f9 7d 00 00 e0 02 c7 05 3c ed f9 7d 00 00 e0 02 75 1f b8 00 00 e0 02 85 c0 74 16 <a1> 00 00 e0 02 c7 05 54 84 8e 7d 00 00 e0 02 a3 58 84 8e 7d eb
[ 8.541519] EIP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d SS:ESP 0068:89c9df2c
[ 8.541519] CR2: 0000000002e00000
[ 8.541519] ---[ end trace 768b6faf51370fc7 ]---
The prefered fix would be to convert the whole IR code to use the kernel IR
infrastructure (which wasn't available at the time this driver had been created).
Until anyone who still has this old hardware steps up an does the conversion,
fix it by not calling the symbol_request calls if the driver is compiled in
without the default IR symbols (CONFIG_DVB_USB_AF9005_REMOTE).
Due to the IR related pointers beeing NULL by default, IR support will then be disabled.
The downside of this solution is, that it will no longer be possible to
compile custom IR symbols (not using CONFIG_DVB_USB_AF9005_REMOTE) in.
Please note that this patch has NOT been tested with all possible cases.
I don't have the hardware and could only verify that it fixes the reported
bug.
Reported-by: Fengguag Wu <fengguang.wu@intel.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a macro to simplify au0828 quirk table. That makes easier
to check it against the USB IDs at drivers/media/usb/au0828/au0828-cards.c.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The lock has been freed in usbvision_release() so there is no need to
call mutex_unlock() here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We call "kfree(ir->i2c_client);" in the error handling and that doesn't
work if "ir" is NULL.
Fixes: 78e719a5f3 ('[media] em28xx-input: i2c IR decoders: improve i2c_client handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
My static checker complains that "i" could be one element beyond the end
of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit e93e7fd9f5 ("v4l2: uvcvideo: Allow
using larger buffers") reworked the buffer size sanity check at buffer
completion time to use the frame size instead of the allocated buffer
size. However, it introduced two bugs in doing so:
- it assigned the allocated buffer size to the frame_size field, instead
of assigning the correct frame size
- it performed the assignment in the S_FMT handler, resulting in the
frame_size field being uninitialized if the userspace application
doesn't call S_FMT.
Fix both issues by removing the frame_size field and validating the
buffer size against the UVC video control dwMaxFrameSize.
Fixes: e93e7fd9f5 ("v4l2: uvcvideo: Allow using larger buffers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this daily build warning:
In file included from build/media_build/v4l/em28xx-core.c:35:0:
build/media_build/v4l/em28xx-core.c: In function 'em28xx_audio_setup':
build/media_build/v4l/em28xx.h:798:2: warning: 'vid' may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(KERN_INFO "%s: "fmt,\
^
build/media_build/v4l/em28xx-core.c:507:6: note: 'vid' was declared here
u32 vid;
^
As far as I can tell 'vid' can not really be used uninitialized here, but the code
is sufficiently complex that apparently gcc can't figure that out.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that loaded modules are const char strings so we don't
load arbitrary modules in the future, nor allow for format string
leaks in the module request call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that loaded modules are const char strings so we don't
load arbitrary modules in the future, nor allow for format string
leaks in the module request call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DUbD
-----END PGP SIGNATURE-----
Merge tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new IR driver: hix5hd2-ir
- the virtual test driver (vivi) was replaced by vivid, with has an
almost complete set of features to emulate most v4l2 devices and
properly test all sorts of userspace apps
- the as102 driver had several bugs fixed and was properly split into a
frontend and a core driver. With that, it got promoted from staging
into mainstream
- one new CI driver got added for CIMaX SP2/SP2HF (sp2 driver)
- one new frontend driver for Toshiba ISDB-T/ISDB-S demod (tc90522)
- one new PCI driver for ISDB-T/ISDB-S (pt3 driver)
- saa7134 driver got support for go7007-based devices
- added a new PCI driver for Techwell 68xx chipsets (tw68)
- a new platform driver was added (coda)
- new tuner drivers: mxl301rf and qm1d1c0042
- a new DVB USB driver was added for DVBSky S860 & similar devices
- added a new SDR driver (hackrf)
- usbtv got audio support
- several platform drivers are now compiled with COMPILE_TEST
- a series of compiler fixup patches, making sparse/spatch happier with
the media stuff and removing several warnings, especially on those
platform drivers that didn't use to compile on x86
- Support for several new modern devices got added
- lots of other fixes, improvements and cleanups
* tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (544 commits)
[media] ir-hix5hd2: fix build on c6x arch
[media] pt3: fix DTV FE I2C driver load error paths
Revert "[media] media: em28xx - remove reset_resume interface"
[media] exynos4-is: fix some warnings when compiling on arm64
[media] usb drivers: use %zu instead of %zd
[media] pci drivers: use %zu instead of %zd
[media] dvb-frontends: use %zu instead of %zd
[media] s5p-mfc: Fix several printk warnings
[media] s5p_mfc_opr: Fix warnings
[media] ti-vpe: Fix typecast
[media] s3c-camif: fix dma_addr_t printks
[media] s5p_mfc_opr_v6: get rid of warnings when compiled with 64 bits
[media] s5p_mfc_opr_v5: Fix lots of warnings on x86_64
[media] em28xx: Fix identation
[media] drxd: remove a dead code
[media] saa7146: remove return after BUG()
[media] cx88: remove return after BUG()
[media] cx88: fix cards table CodingStyle
[media] radio-sf16fmr2: declare some structs as static
[media] radio-sf16fmi: declare pnp_attached as static
...
The reset_resume call is needed, otherwise it will break resume
on some conditions, depending on the usb ehci/xhci controller.
This reverts commit b89193e0b0.
Reported-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The reset_resume call is needed, otherwise it will break resume
on some conditions, depending on the usb ehci/xhci controller.
This reverts commit b89193e0b0.
Reported-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch complains a lot about endiannes issues on as102:
drivers/media/usb/as102/as10x_cmd_stream.c:41:47: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_stream.c:41:47: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd_stream.c:41:47: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_stream.c:43:43: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_stream.c:43:43: expected unsigned short [unsigned] [usertype] pid
drivers/media/usb/as102/as10x_cmd_stream.c:43:43: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_stream.c:98:47: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_stream.c:98:47: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd_stream.c:98:47: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_stream.c💯43: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_stream.c💯43: expected unsigned short [unsigned] [usertype] pid
drivers/media/usb/as102/as10x_cmd_stream.c💯43: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_stream.c:142:48: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_stream.c:142:48: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd_stream.c:142:48: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_stream.c:185:47: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_stream.c:185:47: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd_stream.c:185:47: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:46:40: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:46:40: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd_cfg.c:46:40: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:47:36: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:47:36: expected unsigned short [unsigned] [usertype] tag
drivers/media/usb/as102/as10x_cmd_cfg.c:47:36: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:48:37: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:48:37: expected unsigned short [unsigned] [usertype] type
drivers/media/usb/as102/as10x_cmd_cfg.c:48:37: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:72:27: warning: cast to restricted __le32
drivers/media/usb/as102/as10x_cmd_cfg.c:102:40: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:102:40: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd_cfg.c:102:40: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:104:50: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:104:50: expected unsigned int [unsigned] [usertype] value32
drivers/media/usb/as102/as10x_cmd_cfg.c:104:50: got restricted __le32 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:105:36: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:105:36: expected unsigned short [unsigned] [usertype] tag
drivers/media/usb/as102/as10x_cmd_cfg.c:105:36: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:106:37: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:106:37: expected unsigned short [unsigned] [usertype] type
drivers/media/usb/as102/as10x_cmd_cfg.c:106:37: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:156:48: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd_cfg.c:156:48: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd_cfg.c:156:48: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd_cfg.c:197:14: warning: cast to restricted __le16
drivers/media/usb/as102/as10x_cmd.c:40:40: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:40:40: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd.c:40:40: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:81:41: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:81:41: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd.c:81:41: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:123:41: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:123:41: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd.c:123:41: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:124:43: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:124:43: expected unsigned int [unsigned] [usertype] freq
drivers/media/usb/as102/as10x_cmd.c:124:43: got restricted __le32 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:178:48: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:178:48: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd.c:178:48: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:202:17: warning: cast to restricted __le16
drivers/media/usb/as102/as10x_cmd.c:203:24: warning: cast to restricted __le16
drivers/media/usb/as102/as10x_cmd.c:204:24: warning: cast to restricted __le16
drivers/media/usb/as102/as10x_cmd.c:230:48: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:230:48: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd.c:230:48: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:262:25: warning: cast to restricted __le16
drivers/media/usb/as102/as10x_cmd.c:289:48: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:289:48: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd.c:289:48: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:313:17: warning: cast to restricted __le32
drivers/media/usb/as102/as10x_cmd.c:315:17: warning: cast to restricted __le32
drivers/media/usb/as102/as10x_cmd.c:317:17: warning: cast to restricted __le32
drivers/media/usb/as102/as10x_cmd.c:319:17: warning: cast to restricted __le16
drivers/media/usb/as102/as10x_cmd.c:349:48: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:349:48: expected unsigned short [unsigned] [usertype] proc_id
drivers/media/usb/as102/as10x_cmd.c:349:48: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:387:29: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:387:29: expected unsigned short [unsigned] [usertype] req_id
drivers/media/usb/as102/as10x_cmd.c:387:29: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:388:27: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:388:27: expected unsigned short [unsigned] [usertype] prog
drivers/media/usb/as102/as10x_cmd.c:388:27: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:389:30: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:389:30: expected unsigned short [unsigned] [usertype] version
drivers/media/usb/as102/as10x_cmd.c:389:30: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:390:31: warning: incorrect type in assignment (different base types)
drivers/media/usb/as102/as10x_cmd.c:390:31: expected unsigned short [unsigned] [usertype] data_len
drivers/media/usb/as102/as10x_cmd.c:390:31: got restricted __le16 [usertype] <noident>
drivers/media/usb/as102/as10x_cmd.c:408:14: warning: cast to restricted __le16
This happens because of the command endiannes that are sent/received to
the firmware. So, add the correct endiannes tags to the command fields.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for IT930x USB bridge and IT9303 reference design.
It is a DVB-T/T2/C tuner with the following components:
- IT9303 USB bridge
- Si2168-B40 demodulator
- Si2147-A30 tuner
The IT9303 requires firmware that can be downloaded here:
http://trsqr.net/olli/linux/firmwares/it930x/
The Si2168-B40 requires firmware, but the one that is used by PCTV 292e can be used.
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/
The Si2147-A30 tuner does not require firmware loading.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some I2C tuner drivers require that the I2C device of the tuner is added
to the I2C adapter of the demodulator (Si2168+Si2157 for example). Add
possibility to tell af9035_add_i2c_dev which I2C adapter should be used.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support for DVBSky dvb-s2 usb: add dvb-usb-v2 driver for DVBSky dvb-s2
box, no ci support yet.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We know "ret" is zero so we don't need to test for it. It upsets the
static checkers when we test stuff but we know the answer.
drivers/media/usb/as102/as102_usb_drv.c:164 as102_send_ep1() warn: we tested 'ret' before and it was 'false'
drivers/media/usb/as102/as102_usb_drv.c:189 as102_read_ep2() warn: we tested 'ret' before and it was 'false'
Also, we don't need to initialize "ret".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixed various coding styles, ignoring coding style error on line 5 for all files containing a link that is longer than 80 characters long.
Signed-off-by: Amber Thrall <amber.rose.thrall@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting the value of the chip config register to EM28XX_CHIPCFG_AC97 in
case of a read error is a leftover from the past which is no longer
needed.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Field has_audio in struct em28xx_audio_mode is used together with value
EM28XX_NO_AC97 of field ac97 to determine the internal type of audio
(none/i2s/ac97). This makes the code difficult to understand:
!audio_mode.has_audio && audio_mode.ac97 == EM28XX_NO_AC97 => no audio
!audio_mode.has_audio && audio_mode.ac97 != EM28XX_NO_AC97 => BUG
audio_mode.has_audio && audio_mode.ac97 == EM28XX_NO_AC97 => AC97 audio
audio_mode.has_audio && audio_mode.ac97 != EM28XX_NO_AC97 => I2S audio
Simplify the whole thing by introducing an enum em28xx_int_audio_type
which describes the internal audio type (none, ac97, i2s) and is hooked
directly to the device struct. Then get rid of field has_audio in struct
em28xx_audio_mode.
A follow-up patch will then remove struct em28xx_ac97_mode and finally
the whole struct em28xx_audio_mode.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As far as we know devices can either have audio class or vendor class
usb interfaces but not both at the same time. Even if both interface
types could be provided by devices at the same time, the current code is
totally broken for that case.
So clean up and simplify the usb audio class handling by replacing
fields "has_audio_class" (device has usb audio class compliant
interface) and "has_alsa_audio" (device has vendor audio interface) in
struct em28xx with a single enum em28xx_usb_audio_type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fields "ac97_feat", "ac97_vendor_id" and "i2s_samplerates" of struct
em28xx_audio_mode are used nowhere, except in function
em28xx_audio_setup(). So get rid of them and use local variables
instead.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to add a limit check here so we don't overflow the buffer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to use hex_dump_to_buffer() since we have a kernel helper to
dump up to 64 bytes just via printk().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1409603039
This reverts
commit b99f0aadd3
Author: Mauro Carvalho Chehab <m.chehab@samsung.com>
[media] em28xx: check if a device has audio earlier
Better to split chipset detection from the audio setup. So, move the
detection code to em28xx_init_dev().
It broke analog audio of the Hauppauge winTV HVR 900 and very likely many other
em28xx devices.
Background:
The local variable has_audio in em28xx_usb_probe() describes if the currently
probed _usb_interface_ has an audio endpoint, while dev->audio_mode.has_audio
means that the _device_ as a whole provides analog audio.
Hence it is wrong to set dev->audio_mode.has_audio = has_audio in em28xx_usb_probe().
As result, audio support is no longer detected and configured on devices which
have the audio endpoint on a separate interface, because em28xx_audio_setup()
bails out immediately at the beginning.
Revert the faulty commit to restore the old audio detection procedure, which checks
the chip configuration register to determine if the device has analog audio.
Cc: <stable@vger.kernel.org> # 3.14 to 3.16
Reported-by: Oravecz Csaba <oravecz@nytud.mta.hu>
Tested-by: Oravecz Csaba <oravecz@nytud.mta.hu>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for:
[2040:b139] Hauppauge WinTV HVR-901H (1114xx)
According to the inf file, the hardware is similar to [2040:b131] Hauppauge WinTV 930C-HD (model 1114xx)
The only difference is the demod Si2161 instead of Si2165 (but both are
supported by the si2165 driver).
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for:
[2040:b138] Hauppauge WinTV HVR-900H (111xxx)
The hardware is similar to [2040:b130] Hauppauge WinTV 930C-HD (model 1113xx)
The only difference is the demod Si2161 instead of Si2165 (but both are
supported by the si2165 driver).
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@
struct i1 i2 = { is,
+ .fld = e
- e
,...};
// </smpl>
Not sure why, but some tables are still using the old way,
but at least several of them got fixed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is used by the I2C code in order to slow down the
speed to 20 kHz on devices with xc5000 or xc5000c.
So, it needs to be filled for all devices that use either
xc5000 or xc5000c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, the au0828 driver uses .tuner to detect if analog
tv is being used or not. By not filling .tuner fields at the
board struct, the I2C core can't do decisions based on it.
So, add a field to explicitly tell when analog TV is supported.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This comment is already at the au0828-i2c where it belongs.
So, remove it from a board's entry. It doesn't make any sense
there, as we're setting the clock to 250kHz there, slowing it
down only at the au0828-i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a temporary stack allocated i2c_client in em28xx_i2c_ir_handle_key(),
allocate/free the i2c_client at module init/uninit and hook it into struct em28xx_IR
(if the device has an i2c IR decoder).
This reduces the frame size of function em28xx_i2c_ir_handle_key() and speeds
it up a bit.
Also make sure that all fields of struct i2c_client are initialized properly.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 747dba7de2.
It breaks concurrent vbi and video capturing:
While v4l2->users is the number of users of the whole device (all device nodes),
v4l2_fh_is_singular() only checks the number of users of a specific device node.
As a result. if one device node is open and a second device node is opened
(closed), the device is reinitialized (streaming is stopped).
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When both VBI and video are streaming, and video stream is stopped,
a subsequent trial to restart it will fail, because S_FMT will
return -EBUSY.
That prevents applications like zvbi to work properly.
Please notice that, while this fix it fully for zvbi, the
best is to get rid of streaming_users and res_get logic as a hole.
However, this single-line patch is better to be merged at -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two modprobe parameters for VBI that aren't used
anywhere (one for debug, the other one related to the buffer
size). Get rid of them!
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Morgan Phillips <winter2718@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Morgan Phillips <winter2718@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A test in uvc_video_decode_isoc() checks whether an image has been
received from the camera completely. For this the data amount is compared
to the buffer length, which, however, doesn't have to be equal to the
image size. Switch to using formats .sizeimage field for an exact
expected image size.
[Renamed image_size to frame_size]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/hackrf/hackrf.c:64:3: warning: this decimal constant is unsigned only in ISO C90 [enabled by default]
.rangehigh = 4294967294, /* max u32, hw goes over 7GHz */
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2 driver for HackRF SDR. Very basic version, with reduced
feature set. Driver implements receiver only, hardware supports
also transmitter.
USB ID 1d50:6089. Model HackRF One
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported on [1], this device needs this quirk to be able to
reliably initialise the webcam.
[1] http://ubuntuforums.org/showthread.php?t=2145996
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvcvideo webcam driver exposes the v4l2 control "Exposure (Absolute)"
which allows the user to control the exposure time of the webcam,
essentially controlling the brightness of the received image. By default
the webcam automatically adjusts the exposure time automatically but the
if you set the control "Exposure, Auto"="Manual Mode" the user can fix
the exposure time.
Unfortunately it seems that the Logitech C920 has a firmware bug where
it will forget that it's in manual mode temporarily during initialisation.
This means that the camera doesn't respect the exposure time that the user
requested if they request it before starting to stream video. They end up
with a video stream which is either too bright or too dark and must reset
the controls after video starts streaming.
This patch introduces the quirk UVC_QUIRK_RESTORE_CTRLS_ON_INIT which
causes the cached controls to be re-uploaded to the camera immediately
after initialising the camera. This quirk is applied to the C920 to work
around this camera bug.
Signed-off-by: William Manley <will@williammanley.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Map V4L2_CID_TILT_SPEED and V4L2_CID_PAN_SPEED to the standard UVC
CT_PANTILT_RELATIVE_CONTROL terminal control request.
Tested by plugging a Logitech ConferenceCam C3000e USB camera
and controlling pan/tilt from the userspace using the VIDIOC_S_CTRL ioctl.
Verified that it can pan and tilt at the same time in both directions.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used tda18212 tuner is implemented as a I2C driver. Use em28xx
tuner I2C client for tda18212 driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used tda18212 tuner is implemented as I2C driver. Implement I2C
client to anysee and use it for tda18212.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It crash kernel when device was removed while it was streaming.
That is because we removed driver and frontend thread was still
running. Use new callback which allows I2C driver removal just
after frontend is unregistered.
V2: fixed by reported by Daniel
Reported-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add tuner_detach callback in order to allow custom detach. It is
needed when tuner driver is implemented I2C client or some other
kernel bus, but not proprietary dvb_attach / dvb_detach.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add frontend_detach callback in order to allow custom detach. It is
needed when demod driver is implemented I2C client or some other
kernel bus, but not proprietary dvb_attach / dvb_detach.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I2C driver address is passed as a i2c_new_device() parameter when
device is created. Thus no need to keep it in config struct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Biggest problem of that function is complexity. Try reduce complexity:
* define macros to detect all 3 supported xfers
* remove duplicate message maximum size checks
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Re-implement sleep. Based USB sniffs taken from the latest Hauppauge
windows driver version 07/10/2014, 14.6.23.32191.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change the it913x driver to use the I2C high lever tuner
binding model. As af9035 depends on it, add a code there
to do the binding.
[mchehab@osg.samsung.com: Merge 3 patches into one, because
we don't want to break bisect due to the conversion]
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove tuner_ prefix from module name and file names. Prefix was
added due to file name conflict on media out-tree build system.
Demodulator having same name does not exists anymore. So lets
remove dumb prefix.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reverts commit 3ab2512337
[media] af9035: override tuner for AVerMedia A835B devices
Original commit itself is correct, but it was replaced by more
general solution (commit 1cbbf90d04).
This old solution was committed by a accident and is not needed
anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Integrated RF tuner of IT9135 is connected to demod clock source
named dyn0_clk. Enable that clock source in order to provide stable
clock early enough.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init flags before calling spin_lock_irqsave().
spin_lock_irqsave is macro which stores value to 'flags'.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Kernel logging system needs pointer to usb interface device in
order to print names and bus numbers properly. There was wrong
device pointer given and log printings wasn't correct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sample rate calculation gives a little bit too large results because
in real life there was around one milliseconds (~one usb packet) too
much data for given time. Calculate time more accurate in order to
provide better results.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init flags before calling spin_lock_irqsave().
spin_lock_irqsave is a macro which stores value to 'flags'.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Kernel logging system needs pointer to usb interface device in
order to print names and bus numbers properly. There was wrong
device pointer given and log printings wasn't correct.
Remove some debug logging from v4l2 ioctl functions. v4l2 core debug
prints almost same information when enabled.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Free all reserved USB buffers and URBs on failure. Return all queued
buffers to vb2 with state queued on error case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix indentation of a comment, put it on the same level of the code it
refers to.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
add the following IDs
USB_PID_PCTV_78E (0x025a) for PCTV 78e
USB_PID_PCTV_79E (0x0262) for PCTV 79e
For these it9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using if (foo == false), just use
if (!foo).
That allows a faster mental parsing when analyzing the
code.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/em28xx/em28xx-core.c:297:16: warning: cast to restricted __le16
drivers/media/usb/em28xx/em28xx-cards.c:2249:20: warning: symbol 'em28xx_bcount' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/cx231xx/cx231xx-avcore.c:2226:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2447:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2475:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2500:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2647:18: warning: incorrect type in assignment (different base types)
drivers/media/usb/cx231xx/cx231xx-avcore.c:2659:21: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-dvb.c:743:57: warning: Using plain integer as NULL pointer
drivers/media/usb/cx231xx/cx231xx-dvb.c:776:57: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/pwc/pwc-v4l.c:55:12: warning: symbol 'pwc_auto_whitebal_qmenu' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:24:5: warning: symbol 'dvb_usbv2_disable_rc_polling' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/s2255/s2255drv.c:2248:20: warning: cast to restricted __le16
At the USB structs there are two different idProduct:
usb_device_id::idProduct - already on CPU endiannes
usb_device::descriptor.idProduct - with is LE16
In this specific case, the driver checks for the one at usb_device_id
struct, with already have CPU endianness. So, no conversion is required.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/gspca/kinect.c:151:19: warning: incorrect type in assignment (different base types)
drivers/media/usb/gspca/kinect.c:152:19: warning: incorrect type in assignment (different base types)
drivers/media/usb/gspca/kinect.c:153:19: warning: incorrect type in assignment (different base types)
drivers/media/usb/gspca/kinect.c:191:13: warning: restricted __le16 degrades to integer
drivers/media/usb/gspca/kinect.c:217:16: warning: incorrect type in assignment (different base types)
drivers/media/usb/gspca/kinect.c:218:16: warning: incorrect type in assignment (different base types)
Note that this fixes a real bug where cpu_to_le16 was used instead of the correct
le16_to_cpu.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb/pctv452e.c:886:64: warning: Using plain integer as NULL pointer
drivers/media/usb/dvb-usb/pctv452e.c:903:63: warning: Using plain integer as NULL pointer
drivers/media/usb/dvb-usb/pctv452e.c:968:19: warning: Using plain integer as NULL pointer
drivers/media/usb/dvb-usb/pctv452e.c:1026:19: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb-v2/mxl111sf.c:34:5: warning: symbol 'dvb_usb_mxl111sf_isoc' was not declared. Should it be static?
drivers/media/usb/dvb-usb-v2/mxl111sf.c:38:5: warning: symbol 'dvb_usb_mxl111sf_spi' was not declared. Should it be static?
drivers/media/usb/dvb-usb-v2/mxl111sf.c:46:5: warning: symbol 'dvb_usb_mxl111sf_rfswitch' was not declared. Should it be static?
drivers/media/usb/dvb-usb-v2/mxl111sf.c:890:22: warning: symbol 'mxl111sf_i2c_algo' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb/dw2102.c:670:65: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1601:32: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1644:40: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1644:40: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1644:40: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1644:40: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1644:40: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1644:40: warning: restricted __le16 degrades to integer
drivers/media/usb/dvb-usb/dw2102.c:1904:34: warning: symbol 'p1100' was not declared. Should it be static?
drivers/media/usb/dvb-usb/dw2102.c:1911:34: warning: symbol 's660' was not declared. Should it be static?
drivers/media/usb/dvb-usb/dw2102.c:1930:34: warning: symbol 'p7500' was not declared. Should it be static?
drivers/media/usb/dvb-usb/dw2102.c:1937:34: warning: symbol 's421' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no need to keep local copy of usb_device pointer as we
have same pointer stored and available easily from device state.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reported by Dan Carpenter:
The patch d10d1b9ac9: "[media] dvb_usb_v2: use dev_* logging
macros" from Jun 26, 2012, leads to the following Smatch complaint:
drivers/media/usb/dvb-usb-v2/dvb_usb_urb.c:31 dvb_usb_v2_generic_io()
error: we previously assumed 'd' could be null (see line 29)
...
Remove whole check as it must not happen in any case. Driver is
totally broken if it does not have valid pointer to device.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Read MAC address from the EEPROM.
This version two corrects a flaw in the result code returning that
did exist in the first version.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TechnoTrend TT-connect CT2-4650 CI (0b48:3012) is an USB DVB-T2/C tuner with
the following components:
USB interface: Cypress CY7C68013A-56LTXC
Demodulator: Silicon Labs Si2168-A20
Tuner: Silicon Labs Si2158-A20
CI chip: CIMaX SP2HF
The firmware for the tuner is the same as for TechnoTrend TT-TVStick CT2-4400.
See https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
The demodulator needs a firmware that can be extracted from the Windows drivers.
File ttConnect4650_64.sys should be extracted from
http://www.tt-downloads.de/bda-treiber_4.1.0.4.zip (MD5 sum below).
3464bfc37a47b4032568718bacba23fb ttConnect4650_64.sys
Then the firmware can be extracted:
dd if=ttConnect4650_64.sys ibs=1 skip=273376 count=6424 of=dvb-demod-si2168-a20-01.fw
The SP2 CI module requires a definition of a function cxusb_tt_ct2_4650_ci_ctrl
that is passed on to the SP2 driver and called back for CAM operations.
[crope@iki.fi: meld USB ID define patch to this]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TS mode must be set in the existing TechnoTrend CT2-4400 driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TS mode must be set in the existing PCTV 292e driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement set voltage operation.
Separate TS clock as a own configuration parameter.
Add TS clock polarity parameter.
[crope@iki.fi: merge em28xx driver m88ds3103 config change patch
to that one, in order to keep build unbroken]
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Normally, ADAP_STREAMING bit is set in dvb_usb_start_feed and cleared in
dvb_usb_stop_feed.
But in exceptional cases, for example, when the tv is playing programs
and the tuner is pulled out, then dvb_usbv2_disconnect is called.
In such case, it will first call dvb_usbv2_adapter_frontend_exit to stop
dvb_frontend_thread, and then call dvb_usbv2_adapter_dvb_exit to clear
ADAP_STREAMING bit.
At this point, if dvb_frontend_thread is sleeping and waiting for
ADAP_STREAMING to be cleared to get out of sleep. then
dvb_frontend_thread can never be stoped, because clearing ADAP_STREAMING
bit is performed after dvb_frontend_thread is stopped (i.e. performed in
dvb_usbv2_adapter_dvb_exit).
So, deadlock:
[ 240.822037] INFO: task khubd:497 blocked for more than 120 seconds.
[ 240.822655] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.830493] khubd D c0013b3c 0 497 2 0x00000000
[ 240.836996] [<c0013b3c>] (__schedule+0x200/0x54c) from [<c00110f4>] (schedule_timeout+0x14c/0x19c)
[ 240.845940] [<c00110f4>] (schedule_timeout+0x14c/0x19c) from [<c00137f4>] (wait_for_common+0xac/0x150)
[ 240.855234] [<c00137f4>] (wait_for_common+0xac/0x150) from [<c004989c>] (kthread_stop+0x58/0x90)
[ 240.864004] [<c004989c>] (kthread_stop+0x58/0x90) from [<c03b2ebc>] (dvb_frontend_stop+0x3c/0x9c)
[ 240.872849] [<c03b2ebc>] (dvb_frontend_stop+0x3c/0x9c) from [<c03b2f3c>] (dvb_unregister_frontend+0x20/0xd8)
[ 240.882666] [<c03b2f3c>] (dvb_unregister_frontend+0x20/0xd8) from [<c03ed938>] (dvb_usbv2_exit+0x68/0xfc)
[ 240.892204] [<c03ed938>] (dvb_usbv2_exit+0x68/0xfc) from [<c03eda18>] (dvb_usbv2_disconnect+0x4c/0x70)
[ 240.901499] [<c03eda18>] (dvb_usbv2_disconnect+0x4c/0x70) from [<c031c050>] (usb_unbind_interface+0x58/0x188)
[ 240.911395] [<c031c050>] (usb_unbind_interface+0x58/0x188) from [<c02c3e78>] (__device_release_driver+0x74/0xd0)
[ 240.921544] [<c02c3e78>] (__device_release_driver+0x74/0xd0) from [<c02c3ef0>] (device_release_driver+0x1c/0x28)
[ 240.931697] [<c02c3ef0>] (device_release_driver+0x1c/0x28) from [<c02c39b8>] (bus_remove_device+0xc4/0xe4)
[ 240.941332] [<c02c39b8>] (bus_remove_device+0xc4/0xe4) from [<c02c1344>] (device_del+0xf4/0x178)
[ 240.950106] [<c02c1344>] (device_del+0xf4/0x178) from [<c0319eb0>] (usb_disable_device+0xa0/0x1c8)
[ 240.959040] [<c0319eb0>] (usb_disable_device+0xa0/0x1c8) from [<c03128b4>] (usb_disconnect+0x88/0x188)
[ 240.968326] [<c03128b4>] (usb_disconnect+0x88/0x188) from [<c0313edc>] (hub_thread+0x4d0/0x1200)
[ 240.977100] [<c0313edc>] (hub_thread+0x4d0/0x1200) from [<c0049690>] (kthread+0xa4/0xb0)
[ 240.985174] [<c0049690>] (kthread+0xa4/0xb0) from [<c0009118>] (ret_from_fork+0x14/0x3c)
[ 240.993259] INFO: task kdvb-ad-0-fe-0:3256 blocked for more than 120 seconds.
[ 241.000349] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 241.008162] kdvb-ad-0-fe-0 D c0013b3c 0 3256 2 0x00000000
[ 241.014507] [<c0013b3c>] (__schedule+0x200/0x54c) from [<c03eda44>] (wait_schedule+0x8/0x10)
[ 241.022924] [<c03eda44>] (wait_schedule+0x8/0x10) from [<c001120c>] (__wait_on_bit+0x74/0xb8)
[ 241.031434] [<c001120c>] (__wait_on_bit+0x74/0xb8) from [<c00112b8>] (out_of_line_wait_on_bit+0x68/0x70)
[ 241.040902] [<c00112b8>] (out_of_line_wait_on_bit+0x68/0x70) from [<c03e5e88>] (dvb_usb_fe_sleep+0xf4/0xfc)
[ 241.050618] [<c03e5e88>] (dvb_usb_fe_sleep+0xf4/0xfc) from [<c03b4b74>] (dvb_frontend_thread+0x124/0x4e8)
[ 241.060164] [<c03b4b74>] (dvb_frontend_thread+0x124/0x4e8) from [<c0049690>] (kthread+0xa4/0xb0)
[ 241.068929] [<c0049690>] (kthread+0xa4/0xb0) from [<c0009118>] (ret_from_fork+0x14/0x3c)
Fix it by calling dvb_usbv2_adapter_frontend_exit() latter.
Test enviroment: odroidx2 + Hauppauge(WinTV-Aero-M)
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fix spelling typo in printk within vairous
part of the code.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that alsa code is part of the driver, it can be compiled
only if alsa is enabled.
drivers/built-in.o: In function `snd_usbtv_hw_free':
>> usbtv-audio.c:(.text+0x21eb55): undefined reference to `snd_pcm_lib_free_pages'
drivers/built-in.o: In function `snd_usbtv_hw_params':
>> usbtv-audio.c:(.text+0x21eb72): undefined reference to `snd_pcm_lib_malloc_pages'
drivers/built-in.o: In function `usbtv_audio_urb_received':
>> usbtv-audio.c:(.text+0x21ed66): undefined reference to `snd_pcm_link_rwlock'
>> usbtv-audio.c:(.text+0x21ed9f): undefined reference to `snd_pcm_link_rwlock'
>> usbtv-audio.c:(.text+0x21edf5): undefined reference to `snd_pcm_period_elapsed'
drivers/built-in.o: In function `usbtv_audio_init':
>> (.text+0x21f00a): undefined reference to `snd_card_new'
drivers/built-in.o: In function `usbtv_audio_init':
>> (.text+0x21f0a2): undefined reference to `snd_pcm_new'
drivers/built-in.o: In function `usbtv_audio_init':
>> (.text+0x21f0e5): undefined reference to `snd_pcm_set_ops'
drivers/built-in.o: In function `usbtv_audio_init':
>> (.text+0x21f103): undefined reference to `snd_pcm_lib_preallocate_pages_for_all'
drivers/built-in.o: In function `usbtv_audio_init':
>> (.text+0x21f10c): undefined reference to `snd_card_register'
drivers/built-in.o: In function `usbtv_audio_init':
>> (.text+0x21f12a): undefined reference to `snd_card_free'
drivers/built-in.o: In function `usbtv_audio_free':
>> (.text+0x21f15c): undefined reference to `snd_card_free'
>> drivers/built-in.o:(.data+0x43250): undefined reference to `snd_pcm_lib_ioctl'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
au0828 doesn't resume correctly and TV tuning fails with
xc_set_signal_source(0) failed message. Change au0828 dvb
suspend and resume interfaces to suspend and resume frontend
during suspend and resume respectively. dvb_frontend_suspend()
suspends tuner and fe using tuner and fe ops. dvb_frontend_resume()
resumes fe and tuner using fe and tuner ops ini before waking up
the frontend. With this change HVR950Q suspend and resume work
when system gets suspended when digital function is tuned to a
channel and with active TV stream, and after resume it went right
back to active TV stream.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The correct field order in progressive mode is V4L2_FIELD_NONE, not V4L2_FIELD_INTERLACED.
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a new video frame is started, the driver takes the next video buffer from
the list of active buffers and moves it to dev->usb_ctl.vid_buf / dev->usb_ctl.vbi_buf
for further processing.
On streaming stop we currently only give back the pending buffers from the list
but not the ones which are currently processed.
This causes the following warning from the vb2 core since kernel 3.15:
...
------------[ cut here ]------------
WARNING: CPU: 1 PID: 2284 at drivers/media/v4l2-core/videobuf2-core.c:2115 __vb2_queue_cancel+0xed/0x150 [videobuf2_core]()
[...]
Call Trace:
[<c0769c46>] dump_stack+0x48/0x69
[<c0245b69>] warn_slowpath_common+0x79/0x90
[<f925e4ad>] ? __vb2_queue_cancel+0xed/0x150 [videobuf2_core]
[<f925e4ad>] ? __vb2_queue_cancel+0xed/0x150 [videobuf2_core]
[<c0245bfd>] warn_slowpath_null+0x1d/0x20
[<f925e4ad>] __vb2_queue_cancel+0xed/0x150 [videobuf2_core]
[<f925fa35>] vb2_internal_streamoff+0x35/0x90 [videobuf2_core]
[<f925fac5>] vb2_streamoff+0x35/0x60 [videobuf2_core]
[<f925fb27>] vb2_ioctl_streamoff+0x37/0x40 [videobuf2_core]
[<f8e45895>] v4l_streamoff+0x15/0x20 [videodev]
[<f8e4925d>] __video_do_ioctl+0x23d/0x2d0 [videodev]
[<f8e49020>] ? video_ioctl2+0x20/0x20 [videodev]
[<f8e48c63>] video_usercopy+0x203/0x5a0 [videodev]
[<f8e49020>] ? video_ioctl2+0x20/0x20 [videodev]
[<c039d0e7>] ? fsnotify+0x1e7/0x2b0
[<f8e49012>] video_ioctl2+0x12/0x20 [videodev]
[<f8e49020>] ? video_ioctl2+0x20/0x20 [videodev]
[<f8e4461e>] v4l2_ioctl+0xee/0x130 [videodev]
[<f8e44530>] ? v4l2_open+0xf0/0xf0 [videodev]
[<c0378de2>] do_vfs_ioctl+0x2e2/0x4d0
[<c0368eec>] ? vfs_write+0x13c/0x1c0
[<c0369a8f>] ? vfs_writev+0x2f/0x50
[<c0379028>] SyS_ioctl+0x58/0x80
[<c076fff3>] sysenter_do_call+0x12/0x12
---[ end trace 5545f934409f13f4 ]---
...
Many thanks to Hans Verkuil, whose recently added check in the vb2 core unveiled
this long standing issue and who has investigated it further.
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an ALSA handler inside usbtv module, in order to make
audio to work with those devices.
Signed-off-by: Federico Simoncelli <fsimonce@redhat.com>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the dependencies of as102_cmd from as102, in order to
allow it to be compiled as a separate module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function just converts from the as10x internal data into
the DVBv5 cache. Get rid of it.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function just parses the frontend cache and converts
to the as102 internal format message. Get rid of it.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Avoid having function prototypes by moving some
ancillary routines to the beginning of the file.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver is stable and doesn't contain any really serious
issue. Move it out of staging.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for PCTV microStick (77e) device that uses a sms1140
chipset.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When DVB is streaming and suspend is called, it will call
au0828_stop_transport(), with will clean the streaming flag.
Due to that, stop_urb_transfer() will be called twice,
causing an oops.
So, we need another flag to be used at resume, telling it
to restart DVB.
While here, add a logic at stop_urb_transfer() to prevent
it of being called twice, and convert the usb_streaming
flag into boolean.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dev->dvb is always not null, as it is an area at the dev
memory. So, checking if (dev->dvb) is always true.
Instead of this stupid check, what the code wants to do is
to know if the DVB was successully registered.
Fix it by checking, instead, for dvb->frontend. It should
also be sure that this var will be NULL if the device was
not properly initialized.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Suspend/resume conditions can be very tricky. Add some info
printk's to help tracking what's happening there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using printk(KERN_foo, use pr_foo() macros.
No functional changes.
Note: we should do the same for dprintk(), but that would
require to remove the dprintk levels. So, for now, let's
not touch on it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No timers should be enabled during suspend. So,
stop them. At resume time, we should do the proper
initialization for it to keep working.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The STREAM_ON state is used by s_format callback,
but the driver never sets it.
Fix it. This will also be needed in order to handle
suspend/resume ops.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The scheduled work should be cancelled during suspend.
At resume time, we need to set the frontend again. So,
add such logic to the driver.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
At resume, we should restore the register contents. So,
reenable the bridge and GPIO settings.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Trying to make au0828 to suspend can do very bad things, as
the polling Kthread is not handled. We should disable it
during suspend, only re-enabling it at resume.
Still, analog and digital TV won't work, as we don't reinit
the settings at resume, but at least it won't hang.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Define au0828_rc_*() stubs to avoid compile errors when
VIDEO_AU0828_RC is disabled and avoid the need to enclose
au0828_rc_*() in ifdef CONFIG_VIDEO_AU0828_RC in .c files.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It doesn't make sense to handle an IR code given before
suspending after the device resume. So, turn off IR
int while suspending.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As the RC kthread can re-enable IR int, we should first
cancel the kthread and then disable IR int.
While here, remove a temporary debug printk.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the DVB code sets the frontend, it disables the IR
INT, probably due to some hardware bug, as there's no code
there at au8522 frontend that writes on register 0xe0.
Fixing it at au8522 code is hard, as it doesn't know if the
IR is enabled or disabled, and just restoring the value of
register 0xe0 could cause other nasty effects. So, better
to add a hack at au0828-input polling interval to enable int,
if disabled.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The IR code increases the power consumption of the device.
Allow to disable it via modprobe parameter.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This sleep was doing some debouncing on the original driver.
This is not needed on Linux, because the RC core and the input
layer already takes care of it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
- removal of sn9c102. This device driver was replaced a long time ago
by gspca
- solo6x10 and go7007 webcam drivers moved from staging into
mainstream. They were waiting for an API to allow setting the image
detection matrix
- SDR drivers moved from staging into mainstream: sdr-msi3101 (renamed
as msi2500) and rtl2832
- added SDR driver for airspy
- added demux driver: si2165
- rework at several RC subsystem, making the code for RC-5 SZ variant
to be added at the standard RC5 decoder
- added decoder for the XMP IR protocol
- tuner driver moved from staging into mainstream: msi3101 (renamed as
msi001)
- added documentation for some additional SDR pixfmt
- some device tree bindings documented
- added support for exynos3250 at s5p-jpeg
- remove the obsolete, unmaintained and broken mx1_camera driver
- added support for remote controllers at au0828 driver
- added a RC driver: sunxi-cir
- several driver fixes, enhancements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (455 commits)
[media] cx23885: fix UNSET/TUNER_ABSENT confusion
[media] coda: fix build error by making reset control optional
[media] radio-miropcm20: fix sparse NULL pointer warning
[media] MAINTAINERS: Update go7007 pattern
[media] MAINTAINERS: Update solo6x10 patterns
[media] media: atmel-isi: add primary DT support
[media] media: atmel-isi: convert the pdata from pointer to structure
[media] media: atmel-isi: add v4l2 async probe support
[media] rcar_vin: add devicetree support
[media] media: pxa_camera device-tree support
[media] media: mt9m111: add device-tree suppport
[media] soc_camera: add support for dt binding soc_camera drivers
[media] media: soc_camera: pxa_camera documentation device-tree support
[media] media: mt9m111: add device-tree documentation
[media] s5p-mfc: remove unnecessary calling to function video_devdata()
[media] s5p-jpeg: add chroma subsampling adjustment for Exynos3250
[media] s5p-jpeg: Prevent erroneous downscaling for Exynos3250 SoC
[media] s5p-jpeg: Assure proper crop rectangle initialization
[media] s5p-jpeg: fix g_selection op
[media] s5p-jpeg: Adjust jpeg_bound_align_image to Exynos3250 needs
...
HVR-950Q uses an I2C remote controller at address 0x47 (7-bits
notation). Add support for it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commits 21dc61d3c0 and 7a1dd50b89 reduced the board I2C
speed to 20 MHz by default, due to a I2C stretch issue:
while xc5000 uses i2c stretch when a command is sent to it,
au0828 doesn't support this feature.
However, this is needed only for Xceive tuners. The other
I2C devices can work at the max speed.
So, revert the workarounds at board level, handling it at
I2C level, only when talking with xc5000.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following warnings:
drivers/media/usb/cx231xx/cx231xx-cards.c: In function 'read_eeprom':
drivers/media/usb/cx231xx/cx231xx-cards.c:979:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for:
[2040:b130] Hauppauge WinTV 930C-HD (model 1113xx)
After loading the driver the first open to dvb device node fails.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed to support PCTV QuatroStick 522e which uses a si2157.
The si2157 driver is written using i2c_client attachment.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using some random value, return an error if the
PCB config is not available or doesn't match a know profile
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That makes easier to understand the code. It would also help
to add support for having boards with just digital support
on some latter patch, as allowed by some PCB configs.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The initialization is already too complex. Use devm_ functions
to make the code simpler and easier to modify.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On some newer boards, like HVR-930C HD, the information at
the PCB tables are sometimes higher than the ones actually
available on the device. That causes the probing code to
go past the interfaces array.
Add checks to the interface number before going past the
array.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes an old copy+paste bug that has survived all recent code
changes in this code area.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of counting the number of opened file handles, use function
v4l2_fh_is_singular_file() in em28xx_v4l2_open() and em28xx_v4l2_close() to
determine if the file handle is the first/last opened one.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of calling
...
struct v4l2_fh *fh = kzalloc(sizeof(*fh), GFP_KERNEL);
filp->private_data = fh;
v4l2_fh_init(fh, vdev);
v4l2_fh_add(fh);
...
simply use function v4l2_fh_open() which does all of these calls for us.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
struct em28xx_fh isn't needed anymore because the only used field which is left is struct v4l2_fh fh.
Use struct v4l2_fh directly and remvove struct em28xx_fh.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pointer v4l2" can be used instead of "dev->v4l2, which saves some characters.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Expression ((7bit i2c_addr << 1) & 0x01) can not be right
because it is always 0
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix checkpatch warning:
WARNING: usb_free_urb(NULL) is safe this check is probably not required
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tuner ID set into EEPROM is wrong, which causes driver to select
wrong tuner profile. That leads device non-working. Fix issue by
overriding known bad tuner IDs with suitable default value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change em28xx_dvb_fini() to set fe exit flag to DVB_FE_DEVICE_REMOVED
when device is disconnected. em28xx maintains device disconnect status
in em28xx device. fe drivers will be able to now check the fe exit
status to avoid accessing the device, from their release interfaces
when called from disconnect path. This change depends on dvb-core
change that exports fe exit flag by moving it from fepriv to fe.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In em28xx usb disconnect code path, some dvb fe and tuner drivers
attempt i2c transfers from their release interfaces. When device
is removed, return -ENODEV instead of attempting to transfer data
over i2c.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx uses resume interface as its reset_resume interface.
If usb device is reset during suspend, reset_resume doesn't
do the necessary initialization which leads to resume failure.
Many systems don't maintain do not maintain suspend current to
the USB host controllers during hibernation. Remove reset_resume
to allow disconnect to be called followed by device restore
sequence.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add error hanlding when EM2870_BOARD_KWORLD_A340 dvb_attach()
for fe and tuner fail in em28xx_dvb_init().
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx_dvb_resume() unregisters i2c tuner, i2c demod, and dvb.
This erroneous cleanup results in i2c tuner, i2c demod, and dvb
devices unregistered and removed during resume. This error is a
result of merge conflict between two patches that went into 3.15.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added Sveon STV21 device based on Realtek RTL2832U and FC0013 tuner
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix regression in some dib0700 based devices.
Set size_of_priv, and don't call dvb_detach unnecessarily.
This resolves the oops(s) for my "Leadtek Winfast DTV Dongle (STK7700P based)"
Signed-off-by: James Harper <james.harper@ejbdigital.com.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We already have dev->scancode_filter and dev->scancode_wakeup_filter
so rename dev->scanmask to dev->scancode_mask for consistency.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
the RC RX packet is defined as:
struct dib0700_rc_response {
...
u8 not_system;
u8 system;
...
u8 data;
u8 not_data;
The NEC protocol transmits in the order:
system
not_system
data
not_data
Note that the code defines the NEC extended scancode as:
scancode = be16_to_cpu(poll_reply->system16) << 8 | poll_reply->data;
i.e.
scancode = poll_reply->not_system << 16 |
poll_reply->system << 8 |
poll_reply->data;
Which, if the order *is* reversed, would mean that the scancode that
gets defined is in reality:
scancode = poll_reply->system << 16 |
poll_reply->not_system << 8 |
poll_reply->data;
Which is the same as the order used in drivers/media/rc/ir-nec-decoder.c.
This patch changes the code to match my assumption (the generated scancode
should, however, not change).
[m.chehab@samsung.com: rebased and fixed the decoding error message]
Signed-off-by: David Härdeman <david@hardeman.nu>
CC: Patrick Boettcher <pboettcher@kernellabs.com>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Vincent:
[ 16.332247] xc2028 0-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000.
[ 16.344378] cxusb: i2c wr: len=64 is too big!
64 bytes is too short for firmware load on this device. So, increase it
to 80 bytes.
Reported-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the custom motion detection API in this driver has been
replaced with a standard API there is no reason anymore to keep it
in staging. So (finally!) move it to drivers/media/usb.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename driver namespace according to current driver name. Old
msi3101 was name of reference design, msi2500 is name of chip
itself.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was a lot of duplicated functionality between different
stream format handling. Refactor functionality in order to get
rid of duplicated code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move msi3101 out of staging and rename to msi2500.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Print notice on driver load: "SDR API is still slightly
experimental and functionality changes may follow". It is just
remind possible used SDR API is very new and surprises may occur.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move it out of staging into media like all the other SDR drivers
too. There is no good reasons to keep these SDR drivers in staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add software defined radio device support for media Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
The issue was discovered by static analysis. It turns out that code is
somewhat insane, being
if (x) {...} else { if (x) {...} }
Edited it to do the only reasonable thing, which is to log the
information about the failed call. The most descriptive logging commands
set is taken from original code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79801
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The colorspace for HDTV is REC709, not SMPTE240M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_pix_format structure has no reserved field. It is embedded in
the v4l2_framebuffer structure which has no reserved fields either, and
in the v4l2_format structure which has reserved fields that were not
previously required to be zeroed out by applications.
To allow extending v4l2_pix_format, inline it in the v4l2_framebuffer
structure, and use the priv field as a magic value to indicate that the
application has set all v4l2_pix_format extended fields and zeroed all
reserved fields following the v4l2_pix_format field in the v4l2_format
structure.
The availability of this API extension is reported to userspace through
the new V4L2_CAP_EXT_PIX_FORMAT capability flag. Just checking that the
priv field is still set to the magic value at [GS]_FMT return wouldn't
be enough, as older kernels don't zero the priv field on return.
To simplify the internal API towards drivers zero the extended fields
and set the priv field to the magic value for applications not aware of
the extensions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da increased the internal control ranges
to 64 bit, but that caused problems in drivers that use the minimum/maximum/step/default_value
control values in a division or modulus operations since not all architectures support
those natively.
Luckily, in almost all cases it is possible to just cast to 32 bits (the control value
is known to be 32 bits, so it is safe to cast). Only in v4l2-ctrls.c was it necessary to
use do_div in one function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current "wait_on_bit" interface requires an 'action'
function to be provided which does the actual waiting.
There are over 20 such functions, many of them identical.
Most cases can be satisfied by one of just two functions, one
which uses io_schedule() and one which just uses schedule().
So:
Rename wait_on_bit and wait_on_bit_lock to
wait_on_bit_action and wait_on_bit_lock_action
to make it explicit that they need an action function.
Introduce new wait_on_bit{,_lock} and wait_on_bit{,_lock}_io
which are *not* given an action function but implicitly use
a standard one.
The decision to error-out if a signal is pending is now made
based on the 'mode' argument rather than being encoded in the action
function.
All instances of the old wait_on_bit and wait_on_bit_lock which
can use the new version have been changed accordingly and their
action functions have been discarded.
wait_on_bit{_lock} does not return any specific error code in the
event of a signal so the caller must check for non-zero and
interpolate their own error code as appropriate.
The wait_on_bit() call in __fscache_wait_on_invalidate() was
ambiguous as it specified TASK_UNINTERRUPTIBLE but used
fscache_wait_bit_interruptible as an action function.
David Howells confirms this should be uniformly
"uninterruptible"
The main remaining user of wait_on_bit{,_lock}_action is NFS
which needs to use a freezer-aware schedule() call.
A comment in fs/gfs2/glock.c notes that having multiple 'action'
functions is useful as they display differently in the 'wchan'
field of 'ps'. (and /proc/$PID/wchan).
As the new bit_wait{,_io} functions are tagged "__sched", they
will not show up at all, but something higher in the stack. So
the distinction will still be visible, only with different
function names (gds2_glock_wait versus gfs2_glock_dq_wait in the
gfs2/glock.c case).
Since first version of this patch (against 3.15) two new action
functions appeared, on in NFS and one in CIFS. CIFS also now
uses an action function that makes the same freezer aware
schedule call as NFS.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: David Howells <dhowells@redhat.com> (fscache, keys)
Acked-by: Steven Whitehouse <swhiteho@redhat.com> (gfs2)
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steve French <sfrench@samba.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140707051603.28027.72349.stgit@notabene.brown
Signed-off-by: Ingo Molnar <mingo@kernel.org>
USB ID 0b48:3014.
USB interface: Cypress CY7C68013A-56LTXC
Demodulator: Silicon Labs Si2168-30
Tuner: Silicon Labs Si2158-20
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using anonymous initialization for dib0896 structs,
identify each field by name. That helps to understand what's
being initialized.
No functional changes.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since all the drivers that use `struct v4l2_fh' use the core
priority checking, the setting of the flag in the drivers can
be removed.
Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Error handling code in poseidon_probe() misses usb_put_intf()
and usb_put_dev().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the MSI Digivox Trio device.
Signed-off-by: P. van Gaans <w3ird_n3rd@gmx.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the audio encoding is changed the driver calls hdpvr_set_audio
with the current opt->audio_input value. However, that should have
been opt->audio_input + 1. So changing the audio encoding inadvertently
changes the input as well. This bug has always been there.
The second bug was introduced in kernel 3.10 and that broke the
default_audio_input module option handling: the audio encoding was
never switched to AC3 if default_audio_input was set to 2 (SPDIF input).
In addition, since starting with 3.10 the audio encoding is always set
at the start the first bug now always happens when the driver is loaded.
In the past this bug would only surface if the user would change the
audio encoding after the driver was loaded.
Also fixes a small trivial typo (bufffer -> buffer).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Scott Doty <scott@corp.sonic.net>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tuner ID set into EEPROM is wrong in some cases, which causes driver
to select wrong tuner profile. That leads device non-working. Fix
issue by overriding known bad tuner IDs with suitable default value.
Thanks to MX-NET Telekomunikace s.r.o. for providing non-working
DTV stick, that I could fix the bug!
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the depth stream at 10bpp, for now use a 'depth_mode'
command line parameter to switch between video and depth mode.
Signed-off-by: Alexander Sosna <alexander@xxor.de>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently gspca selects the first ISOC input endpoint as the input
transfer endpoint, however some devices can provide streams on endpoints
different then the first one, so some subdrivers (e.g. gspca_kinect) may
want to select a specific endpoint to use as a transfer endpoint.
Add an xfer_ep field to struct gspca_dev, and change alt_xfer() so that
it accepts a parameter which represents a specific endpoint address to
look for.
If a subdriver wants to specify a value for gspca_dev->xfer_ep it can do
that in its sd_config() callback.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While this device doesn't have a scaler (or have it disabled),
the screen dimentions are a function of the standard. Ok, right
now, only 480 lines standards are implemented, although it
supports other ones. Yet, let's calculate the size, to make
easier to add more standards latter.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It seems that there's a bug at au0828 hardware/firmware
related to alternate setting: when the device is already at
alt 5, a further call causes the URBs to receive -ESHUTDOWN.
I found two different encarnations of this issue:
1) at qv4l2, it fails the second time we try to open the
video screen;
2) at xawtv, when audio underrun occurs, with is very
frequent, at least on my test machine.
The fix is simple: just check if alt=5 before calling
set_usb_interface().
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The analog part of au0828 is missing the tuner Kconfig dependency.
That makes the device to not work while in analog mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
The bug happens when:
CONFIG_DVB_DIB8000=m
CONFIG_DVB_USB_DIB0700=y
As a bonus, dib8000 won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with both Pixelview PV-D231 and MyGica S870.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function,
but, on dib8000, there are several exported symbols.
We need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename this function, in order to prepare for
a next patch that will add a new attach() function that
will be the only one exported by this module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change handling of signal_lock on rs2000. Use ibuf[2] to detect
lock as there is a longer wait for lock to appear in ibuf[6].
Remove last_key and key_timeout and use jiffies plus 60ms
to detect that streaming is still active.
If the current jiffies is time_after the interrupt urb overdue and
clear signal lock.
This results in far faster recovery of lock and streaming.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This contains:
- a new frontend/tuner driver set for si2168 and sa2157
- Videobuf 2 core now supports DVB too
- A new gspca sub-driver (dtcs033)
- saa7134 is now converted to use videobuf2
- add support for 4K timings
- several other driver fixes and improvements
PS. This pull request is shorter than usual, partly because I have
some other patches on topic branches that I'll be sending you later
this week"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (286 commits)
[media] au0828-dvb: restore its permission to 644
[media] xc5000: delay tuner sleep to 5 seconds
[media] xc5000: Don't use whitespace before tabs
[media] xc5000: fix CamelCase
[media] xc5000: Don't wrap msleep()
[media] xc5000: get rid of positive error codes
[media] au0828: reset streaming when a new frequency is set
[media] au0828: Improve debug messages for urb_completion
[media] au0828: Cancel stream-restart operation if frontend is disconnected
[media] dib0700: fix RC support on Hauppauge Nova-TD
[media] USB: as102_usb_drv.c: Remove useless return variables
[media] v4l: Fix documentation of V4L2_PIX_FMT_H264_MVC and VP8 pixel formats
[media] m5mols: Replace missing header
[media] staging: lirc: Fix sparse warnings
[media] fix mceusb endpoint type identification/handling
[media] az6027: Added the PID for a new revision of the Elgato EyeTV Sat DVB-S Tuner
[media] DocBook media: fix typo
[media] adv7604: Add missing include to linux/types.h
[media] v4l: Validate fields in the core code for subdev EDID ioctls
[media] v4l: Add support for DV timings ioctls on subdev nodes
...
As reported by Trevor, doing several opening/streaming/closing
operations to the demux causes it to fail.
I was able to simulate this bug too. I also noticed that,
sometimes, changing channels with au0828, the same thing
happens.
Most of the issues seem to be due to some hardware bug, that
causes the device to not fill all the URBs allocated. When
the bug happens, the only known fix is to either replug the
device, or to send an USB reset to it.
There's also a hack a the au0828 driver that starts a thread
that tries to reset the device when a package doesn't start
with a sync.
One of the culpits for this bad hardware behavior seem to be
caused by the lack of stopping and restarting the stream every
time a new channel is set.
This patch warrants that the stream will be properly reset
every time the set_frontend callback is called, partially
solving the problem.
A complete fix, however, would also need to check the PM
conditions for the tuner and demux.
Reported-by: Trevor Graffa <tlgraffa@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sometimes, it helps to know how much data was received by
urb_completion. Add that information to the optional debug
log.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the tuner is already disconnected, It is meaningless to go on doing the
stream-restart operation, It is better to cancel this operation.
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is another clone of AZ6027. This patch adds the relevant PID.
Signed-off-by: Manuel Schönlaub <manuel.schoenlaub@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently stk1160_read_reg() uses a stack-allocated char to get the
read control value. This is wrong because usb_control_msg() requires
a kmalloc-ed buffer.
This commit fixes such issue by kmalloc'ating a 1-byte buffer to receive
the read value.
While here, let's remove the urb_buf array which was meant for a similar
purpose, but never really used.
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.7 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current names clash with include/linux/leds.h namespace,
although there is no compile issue currently this does affect
backports. Drivers should also try to avoid generic namespaces
for things like this.
Cc: Felipe Pena <felipensp@gmail.com>
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both wq_trigger and stream_started are used only to control the em28xx
alsa streaming. They don't belong to em28xx common struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The tuner address is only used by the v4l submodule and at tuner setup and
can be obtained from the board data directly (if specified).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The tda9887 chipset is part of the analog tuner. Move it out of
em28xx-cards.
Also, it is used only one time by the v4l2 sub-module at tuner setup.
With that, we can get rid of an additional data inside the em28xx
common structure.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move V4L2-specific frequency cache to struct em28xx_v4l2.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Despite being at the common em28xx struct, those two fields are
actually taking into account only the usage inside em28xx v4l2
submodule. So, move them out of the common struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move some temporary capture tracking date to the em28xx_v4l2 struct,
as those info are used only by em28xx v4l2 submodule.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move camera sensor resolution and xtal out of em28xx common struct,
as thore are used only by the em28xx v4l2 submodule.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video progressive data fields belong to analog TV. Move them out
of the common em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The analog format struct belongs to analog TV. Move it out of the
common em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TV norm is specific to analog TV reception. move it out of the common
em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video input mode and control data also belong only to the
analog side. move them to struct em28xx_v4l.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The em28xx scaler data are used only for analog video. Move them to
struct em28xx_v4l2.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video and VBI-specific VB2 queue and mutexes are used only by
the v4l2 sub-driver. Move them to the V4L2 struct, preventing
wasting memory if this sub-driver is not used.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are 3 struct video_device at the em28xx common struct,
for video, VBI and radio. They all are used only by the V4L2 driver.
So, move them to the v4l2-specific struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current clock definition applies only to the V4L2 side of the
driver. Move its struct pointer to the v4l2_dev, where it belongs.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Controls are only applicable to V4L2 module. Move the corresponding
data structs to the proper place.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That reduces a little bit the memory footprint when em28xx-video
is not loaded.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The local var hdl is already pointing to &dev->ctrl_handler.
Use it, instead of dereferencing it all the time.
Code cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just a cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is no longer needed since nobody is calling i2c_get_adapdata() anymore.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Function del_timer() does not guarantee that timer was really deleted.
If the timer handler is beeing executed at the moment, the function
does nothing. So, we have a race between del_timer() and kfree(), and
it's possible to use already freed memory in the handler.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx_compression_disable() is a single line function which is called only one
time and this call also isn't needed.
Register 0x26 is always configured as part of the scaler configuration, which
in turn is always done when the resolution changes. And the initial resolution
setting is applied at first device open.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just driver cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
timestamps in v4l2 buffers returned to userspace are updated in
uvc_video_clock_update() which uses timestamps fetched from
uvc_video_clock_decode() by calling unconditionally ktime_get_ts().
Hence setting the module clock param to realtime has no effect before
this patch.
This has been tested with ffmpeg:
ffmpeg -y -f v4l2 -input_format yuyv422 -video_size 640x480 -framerate 30 -i /dev/video0 \
-f alsa -acodec pcm_s16le -ar 16000 -ac 1 -i default \
-c:v libx264 -preset ultrafast \
-c:a libfdk_aac \
out.mkv
and inspecting the v4l2 input starting timestamp.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set error bit for incomplete buffers when end of buffer is detected by
FID toggling (for example when last transaction with EOF is lost).
This prevents passing incomplete buffers to the userspace.
Signed-off-by: Anton Leontiev <bunder@t-25.ru>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add USB ID for Peak DVB-T USB.
[crope@iki.fi: fix Brian email address and indentation]
Signed-off-by: Brian Healy <healybrian@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Warnings due to __le16 / u16 conversions.
Replace offending struct and so stay on cpu domain.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
External LNA between antenna connector and RF tuner is controlled
by EM28178 GPIO 0. GPIO value 1 is LNA active and value 0 is LNA
disabled.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch does not modify existing drivers. It adds subdriver
to gspca for DTCS033 (Scopium) webcam for astrophotography.
The patch adds dtcs033.c and modifies Kconfig and Makefile.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sn9c102 driver is deprecated. It was moved to staging in
anticipation of its removal in a future kernel version. However, USB
devices 0C45:6024 and 0C45:6025 are still handled by sn9c102 when
both sn9c102 and gspca_sonixb are enabled.
We must migrate all the users of these devices to the gspca_sonixb
driver now, so that it gets sufficient testing before the sn9c102
driver is finally phased out.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It printed a little bit too heavy looking error log "DVB: Unable to
find symbol rtl2832_sdr_attach()" when staging module was disabled.
Silence that error by introducing own version of dvb_attach() macro
without the error logging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 SDR extension module is currently on staging. SDR module
headers were included from staging causing direct dependency staging
directory. As a solution, add needed headers to main driver.
Motivation of that change comes from Luis / driver backports project.
Reported-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Cc: backports@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Coverity, there's a potential risk of a division
by zero on some calls to jpeg_set_qual(), if quality is zero.
As quality can't be 0 or lower than that, adds an extra clause
to cover this special case.
Coverity reports: CID#11922280, CID#11922293, CID#11922295
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.
Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The first hunk of this patch got merged wrong, likely due to some
changes at the em28xx resume code. Revert it to reapply it right.
This reverts commit 37571b163c.
Reported-by: Chris Lee <updatelee@gmail.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: stable@vger.kernel.org # Don't apply this patch or 37571b163c
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pointer to device state has been moved to different location during
some change. PCTV 290e LNA function still uses old pointer, carried
over FE priv, and it crash.
Reported-by: Janne Kujanpää <jikuja@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.
Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
commit 340a30c514 "s2255drv: upgrade to videobuf2" changed the API
used by the s2255 driver, but did not modify the Kconfig statement,
which can lead to build errors when no other driver already uses
VIDEOBUF2_VMALLOC. This patch does the necessary Kconfig change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting functions for hardware filter is a bad idea, as it
breaks compilation if:
CONFIG_DVB_USB_AF9035=y
CONFIG_DVB_AF9033=m
Because the PID filter function calls would be hardcoded at
af9035.
The same doesn't happen with af9033_attach() because the
dvb_attach() doesn't hardcode it. Instead, it dynamically
links it at runtime.
However, calling dvb_attach() multiple times is problematic,
as it increments module kref.
So, the better is to pass one parameter for the af9033 module
to fill the hardware filters, and then use it inside af9035.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PID filters are property of af9033 demod. Use PID filters from af9033
driver as it provides those now.
Allow possible dual mode on USB 1.1 mode too as bandwidth could be
just enough when filters are used on both frontends.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In all cases, when the first capture is called, we need to
call the code that unmutes the volume.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 driver provides muxed I2C adapters for tuner bus I2C gate
control. Pass those adapters to rtl2832_sdr and e4000 modules in order
to get rid of proprietary DVB .i2c_gate_ctrl() callback use.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We need depend on I2C_MUX as rtl2832 demod used requires it.
All error/warnings:
warning: (DVB_USB_RTL28XXU) selects DVB_RTL2832 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CORE && I2C && I2C_MUX)
ERROR: "i2c_add_mux_adapter" [drivers/media/dvb-frontends/rtl2832.ko] undefined!
ERROR: "i2c_del_mux_adapter" [drivers/media/dvb-frontends/rtl2832.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver conversion from proprietary DVB tuner model to more
general I2C driver model.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.
Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a device id to support for PX-S1UD (PLEX ISDB-T usb dongle) which
has sms2270.
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes memory leak introduced by
commit 47d8c881c3.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This code is correct but the indenting is wrong and triggers a static
checker warning "add curly braces?".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tree: git://linuxtv.org/media_tree.git master
head: a3550ea665
commit: a3550ea665 [499/499] [media] usbtv: split core and video implementation
reproduce: make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
>> drivers/media/usb/usbtv/usbtv-core.c:119:22: sparse: symbol 'usbtv_id_table' was not declared. Should it be static?
>> drivers/media/usb/usbtv/usbtv-core.c:129:19: sparse: symbol 'usbtv_usb_driver' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the logic a little by removing one level of identation.
Also, it only makes sense to print something if the .fini callback
is actually doing something.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We can't free struct em28xx while one of the extensions is still
using it.
So, add a kref() to control it, freeing it only after the
extensions fini calls.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a queue was canceled, then the buf_finish op was never called for the
pending buffers. So add this call to queue_cancel. Before calling buf_finish
set the buffer state to PREPARED, which is the correct state. That way the
states DONE and ERROR will only be seen in buf_finish if streaming is in
progress.
Since buf_finish can now be called from non-streaming state we need to
adapt the handful of drivers that actually need to know this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no point in trying to decompress a captured frame unless
the buffer state is OK. It won't be used in any other state, and
in fact the contents of the buffer might well be corrupt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buf_finish op should always work, so change the return type to void.
Update the few drivers that use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add bayer 8-bit GUIDs to uvcvideo and associated them with the
corresponding V4L2 pixel formats.
Signed-off-by: Edgar Thier <info@edgarthier.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The UVC specification uses alternate setting selection to notify devices
of stream start/stop. This breaks when using bulk-based devices, as the
video streaming interface has a single alternate setting in that case,
making video stream start and video stream stop events to appear
identical to the device. Bulk-based devices are thus not well supported
by UVC.
The webcam built in the Asus Zenbook UX302LA ignores the set interface
request and will keep the video stream enabled when the driver tries to
stop it. If USB autosuspend is enabled the device will then be suspended
and will crash, requiring a cold reboot.
USB trace capture showed that Windows sends a CLEAR_FEATURE(HALT)
request to the bulk endpoint when stopping the stream instead of
selecting alternate setting 0. The camera then behaves correctly, and
thus seems to require that behaviour.
Replace selection of alternate setting 0 with clearing of the endpoint
halt feature at video stream stop for bulk-based devices. Let's refrain
from blaming Microsoft this time, as it's not clear whether this
Windows-specific but USB-compliant behaviour was specifically developed
to handle bulkd-based UVC devices, or if the camera just took advantage
of it.
CC: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The UVC device provided timestamps are taken from the clock once the
exposure of the frame has begun, not when the reception of the frame would
have been finished as almost anywhere else. Show this to the user space by
using V4L2_BUF_FLAG_TSTAMP_SRC_SOE buffer flag.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The timestamp_type field used to contain only the timestamp type. Soon it
will be used for timestamp source flags as well. Rename the field
accordingly.
[m.chehab@samsung.com: do the change also to drivers/staging/media and at s2255]
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
