[ Upstream commit c3aa5cb264 ]
AHB memory as MMIO should be mapped with ioremap rather than ioremap_wc,
which should have been used initially just to handle unaligned access as
a workaround.
Fixes: d166a73503 ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20231010201524.2021340-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Reset the FLSHxCR1 registers to default value. ROM may set the register
value and it affects the SPI NAND normal functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20230906183254.235847-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174955.4064174-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() and
devm_platform_ioremap_resource_byname() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230706032727.9180-4-frank.li@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When clock rate > 100MHz, use the DLL calibration mode, and finally
add the suggested half of the current clock cycle to sample the data.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230322090451.3179431-2-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DLL config is just to use the default setting, this means
enable the DLL override mode, and use 1 fixed delay cell in the
DLL delay chain, not means "reset" the DLL, so correct this to
avoid confuse.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230322090451.3179431-1-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de> # Rockchip drivers
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org> # Aspeed driver
Reviewed-by: Dhruva Gole <d-gole@ti.com> # SPI Cadence QSPI
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> # spi-stm32-qspi
Acked-by: William Zhang <william.zhang@broadcom.com> # bcm63xx-hsspi driver
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> # DW SSI part
Link: https://lore.kernel.org/r/167847070432.26.15076794204368669839@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-48-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const array ls1028a_soc_attr on the stack, instead
make it static. Also makes the object code smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20221102152904.143423-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device. Instead,
use the specific dev_fwnode() API for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220906161048.39953-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 7e71b85473 ("arm64: dts: ls1028a: fix node name for the
sysclk") the sysclk node name was renamed and broke the erratum
workaround because it tries to fetch a device tree node by its name,
which is very fragile in general. We don't even need the sysclk node
because the only possible sysclk frequency input is 100MHz. In fact, the
erratum says it applies if SYS_PLL_RAT is 3, not that the platform clock
is 300 MHz. Make the workaround more reliable and just drop the unneeded
sysclk lookup.
For reference, the error during the bootup is the following:
[ 4.898400] nxp-fspi 20c0000.spi: Errata cannot be executed. Read via IP bus may not work
Fixes: 82ce7d0e74 ("spi: spi-nxp-fspi: Implement errata workaround for LS1028A")
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211001212726.159437-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the register operation after the clock enable, otherwise system
will stuck when this driver probe.
Fixes: 71d80563b0 ("spi: spi-nxp-fspi: fix fspi panic by unexpected interrupts")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1623317073-25158-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Errata ERR050568 description says that "Flash access by FlexSPI AHB
command may not work with platform frequency equal to 300 MHz" on
LS1028A.
By default, smaller length reads(equal to RX FIFO size) are done by IP
bus and larger length reads using AHB bus. For adding errata workaround,
use IP bus to read entire flash contents and disable AHB path when
platform frequency is 300Mhz.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-5-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver support for imx8dxl which support read through IP bus only
and disable AHB bus due to an IC errata. Use the pre-defined quirk
FSPI_QUIRK_USE_IP_ONLY directly in device-type data to disable AHB read.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-4-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for disabling AHB bus and read entire flash contents via IP
bus only. Please note, this enables IP bus read using a quirk which can
be enabled directly in device-type data or in existence of an errata
where AHB bus may need to be disabled.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-2-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Given the case that bootloader(such as UEFI)'s FSPI driver might not
handle all interrupts before loading kernel, those legacy interrupts
would assert immidiately once kernel's FSPI driver enable them. Further,
if it was FSPI_INTR_IPCMDDONE, the irq handler nxp_fspi_irq_handler()
would call complete(&f->c) to notify others. However, f->c might not be
initialized yet at that time, then cause kernel panic.
Of cause, we should fix this issue within bootloader. But it would be
better to have this pacth to make dirver more robust (by clearing all
interrupt status bits before enabling interrupts).
Suggested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201123025715.14635-1-ran.wang_1@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently NXP fspi driver has support of DT only. Adding ACPI
support to the driver so that it can be used by UEFI firmware
booting in ACPI mode. This driver will be probed if any firmware
will expose HID "NXP0009" in DSDT table.
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Link: https://lore.kernel.org/r/20200911130331.6313-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_get_resource_byname() function returns NULL on error, it
doesn't return error pointers.
Fixes: d166a73503 ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200312113154.GC20562@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply patch from NXP upstream repo to
Enable the octal combination mode in MCR0
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-3-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply patch from NXP upstream repo to
dynamically allocate AHB memory as needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-2-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull in this patch from NXP's upstream repo to
enable fspi on imx8qxp and imx8mm
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-1-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MODULE_LICENSE info to fix below warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/spi/spi-nxp-fspi.o
Typo fix in Boris Brezillon last name.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add octal mode flags for octal I/O data transfer support.
NXP FlexSPI controller supports 8 lines Rx/Tx data transfer.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add driver for NXP FlexSPI host controller
(0) What is the FlexSPI controller?
FlexSPI is a flexsible SPI host controller which supports two SPI
channels and up to 4 external devices. Each channel supports
Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional
data lines) i.e. FlexSPI acts as an interface to external devices,
maximum 4, each with up to 8 bidirectional data lines.
It uses new SPI memory interface of the SPI framework to issue
flash memory operations to up to four connected flash
devices (2 buses with 2 CS each).
(1) Tested this driver with the mtd_debug and JFFS2 filesystem utility
on NXP LX2160ARDB and LX2160AQDS targets.
LX2160ARDB is having two NOR slave device connected on single bus A
i.e. A0 and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses
one flash on A0 and second on B1 i.e. (CS0 and CS3).
Verified this driver on following SPI NOR flashes:
Micron, mt35xu512ab, [Read - 1 bit mode]
Cypress, s25fl512s, [Read - 1/2/4 bit mode]
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
