Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-10-02
This series contains updates to fm10k only.
Jake fixes an issue where PTP applications requesting software timestamps
may complain that the requested mode is not supported, so add a generic
callback for those drivers that have software transmit timestamp support
enabled. Then provides a trivial cleanup where a code was not wrapped
properly. Got make sure that code looks good in a 80 character limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.
The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.
Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:
[549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
[549.664] i40e: probe of 0007:01:00.1 failed with error -15
[...]
[871.644] i40e 0007:01:00.1: The driver for the device stopped because the
device firmware failed to init. Try updating your NVM image.
[871.644] i40e: probe of 0007:01:00.1 failed with error -32
[...]
[872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored
Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.
This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.
CC: <stable@vger.kernel.org>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-10-03
This series contains fixes to i40e only.
Stefan Assmann provides the changes in this series to resolve an issue
where when we run out of MSIx vectors, iWARP gets disabled automatically.
First adds a check for "no vectors left" during MSIx vector allocation
for VMDq, which will prevent more vectors being allocated than available.
Then fixed the MSIx vector redistribution when we reach the hardware limit
for vectors so that additional features like VMDq, iWARP, etc do not get
starved for vectors because the PF is hogging all the resources. Lastly,
fix the issue for flow director by moving the check for the reaching the
vector limit earlier in the code so that a decision can be made on
disabling flow director.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RoCE-specific LL2 logic [as well as GSI support] over
the 'generic' LL2 interface.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add slowpath configuration support for user, dma and memory
regions registration.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the slowpath configurations of Queue Pair verbs
which adds, deletes, modifies and queries Queue Pairs.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the configurations of the protection domain and
completion queues.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the qedr driver - FW notification, resource
initializations, etc.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a skeletal implementation of the qede RoCE driver -
The qedr has some dependencies of the state of the underlying base
interface. This adds some logic required with mutual registrations
and the ability to pass updates on 'intresting' events.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other protocols beside the networking driver need the ability
of passing some L2 traffic, usually [although not limited] for the
purpose of some management traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the MSI-X vector limit is reached the sideband flow
director gets disabled. A bit too early to make that decision, as
vectors may get re-distributed. So move the check further back.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver allocates 1 vector per CPU thread and the current hardware
limit for vectors is 129 per PF. On systems with 128 or more threads
this currently means all vectors are used by the PF leaving no room for
additional features like VMDq, iWARP, etc...
The code that should redistribute the vectors in this case is broken and
never triggers. Fixed the code so that it actually triggers if the
hardware limit is reached and adjust the number of queue pairs
accordingly.
Also the number of initially requested iWARP vectors was not properly
saved when the vector limit was reached, and therefore always zero.
Comparison with debug statement.
Before:
i40e 0000:2d:00.0: VMDq disabled, not enough MSI-X vectors
i40e 0000:2d:00.0: IWARP disabled, not enough MSI-X vectors
i40e 00.0 MSI-X vector distribution: PF 128, VMDq 0, FDSB 0, iWARP 0
After:
i40e 0000:2d:00.0: MSI-X vector limit reached, attempting to redistribute vectors
i40e 00.0 MSI-X vector distribution: PF 78, VMDq 8, FDSB 0, iWARP 42
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During MSI-X vector allocation for VMDq, a check for "no vectors left"
was missing, add it. This prevents more vectors to be allocated than
available.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of error, the function ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Also add check for return value of platform_get_resource().
Fixes: 54e19bc74f ("net: qcom/emac: do not use devm on internal
phy pdev")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial change here to cleanup a checkpatch.pl warning that got
introduced when changing to alloc_workqueue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no need to clk_disable_unprepare(dev->clk)
before it was initialized.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fi->fib_nhs is zero, the router interface pointer is uninitialized, as shown by
this warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c: In function 'mlxsw_sp_router_fib_event':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1674:21: error: 'r' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1643:23: note: 'r' was declared here
This changes the loop so we handle the case the same way as finding no router
interface pointer attached to one of the nexthops to ensure we always
trap here instead of using uninitialized data.
Fixes: b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build-testing this driver with -Wmaybe-uninitialized gives a new false-positive
warning that I can't really explain:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'mlx5e_configure_flower':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:509:3: error: 'old_attr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It's obvious from the code that 'old_attr' is initialized whenever 'old'
is non-NULL here. The warning appears with all versions I tested from gcc-4.7
through gcc-6.1, and I could not come up with a way to rewrite the function
in a more readable way that avoids the warning, so I'm adding another
initialization to shut it up.
Fixes: 8b32580df1 ("net/mlx5e: Add TC vlan action for SRIOV offloads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This generic callback is for drivers which have software Tx timestamp
support enabled. Without this, PTP applications requesting software
timestamps may complain that the requested mode is not supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent cleanup marked cxgb4_dcb_enabled as 'static', which is correct, but this ignored
how the symbol is also exported. In addition, the export can be compiled out when modules
are disabled, causing a harmless compiler warning in configurations for which it is not
used at all:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:282:12: error: 'cxgb4_dcb_enabled' defined but not used [-Werror=unused-function]
This removes the export and moves the function into the correct #ifdef so we only build
it when there are users.
Fixes: 50935857f8 ("cxgb4: mark symbols static where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mac address origin is not dt, you can only safely assign a mac
address after "link up" of the device. If the link is off the clocks are
disabled and because of issues assigning registers when clocks are off the
new mac address cannot be written in .ndo_set_mac_address() on some soc's.
This fix sets the mac address unconditionally in fec_restart(...) and
ensures consistency between fec registers and the network layer.
Signed-off-by: Gavin Schenk <g.schenk@eckelmann.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9638d19e48 ("net: fec: add netif status check before set mac address")
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:2041:5: warning: no previous prototype for 'mtk_get_link_ksettings' [-Wmissing-prototypes]
drivers/net/ethernet/mediatek/mtk_eth_soc.c:2052:5: warning: no previous prototype for 'mtk_set_link_ksettings' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2715:5: warning: no previous prototype for 'cxgb_setup_tc' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements ndo_poll_controller in net_device_ops callbacks for mlx5,
which is necessary to use netconsole with this driver.
Acked-By: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set upper 32 bits of destination register to zeros after
load from the context structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also can address following UBSAN warnings:
[ 36.640343] ================================================================================
[ 36.648772] UBSAN: Undefined behaviour in drivers/net/ethernet/mellanox/mlx4/fw.c:857:26
[ 36.656853] shift exponent 64 is too large for 32-bit type 'int'
[ 36.663348] ================================================================================
[ 36.671783] ================================================================================
[ 36.680213] UBSAN: Undefined behaviour in drivers/net/ethernet/mellanox/mlx4/fw.c:861:27
[ 36.688297] shift exponent 35 is too large for 32-bit type 'int'
[ 36.694702] ================================================================================
Tested:
reboot with UBSAN, no warning.
Signed-off-by: David Decotigny <decot@googlers.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.
The following trace is seen when the error is triggered:
[1.402247] Unable to handle kernel paging request for data at address 0x00001a99
[1.402410] Faulting instruction address: 0xc0000000007e33f8
[1.402450] Oops: Kernel access of bad area, sig: 11 [#1]
[1.402481] SMP NR_CPUS=2048 NUMA PowerNV
[1.402513] Modules linked in:
[1.402545] CPU: 0 PID: 651 Comm: eehd Not tainted 4.4.0-36-generic #55-Ubuntu
[1.402591] task: c000001fe4e42a20 ti: c000001fe4e88000 task.ti: c000001fe4e88000
[1.402742] NIP: c0000000007e33f8 LR: c0000000007e3164 CTR: c000000000595ea0
[1.402787] REGS: c000001fe4e8b790 TRAP: 0300 Not tainted (4.4.0-36-generic)
[1.402832] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 28000422 XER: 20000000
[1.403058] CFAR: c000000000008468 DAR: 0000000000001a99 DSISR: 42000000 SOFTE: 1
GPR00: c0000000007e3164 c000001fe4e8ba10 c0000000015c5e00 0000000000000000
GPR04: 0000000000000001 0000000000000000 0000000000000039 0000000000000299
GPR08: 0000000000000000 0000000000000001 c000001fe4e88000 0000000000000006
GPR12: 0000000000000000 c00000000fb40000 c0000000000e6558 c000003ca1bffd00
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000000d52768
GPR24: c000000000d52740 0000000000000100 c000003ca1b52000 0000000000000002
GPR28: 0000000000000900 0000000000000000 c00000000152a0c0 c000003ca1b52000
[1.404226] NIP [c0000000007e33f8] tg3_io_error_detected+0x308/0x340
[1.404265] LR [c0000000007e3164] tg3_io_error_detected+0x74/0x340
This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].
Fixes: 0486a063b1 ("tg3: prevent ifup/ifdown during PCI error recovery")
Fixes: dfc8f37031 ("net/tg3: Release IRQs on permanent error")
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading addresses, interrupts, and _DSD properties
from ACPI tables, just like with device tree. The HID for the
EMAC device itself is QCOM8070. The internal PHY is represented
by a child node with a HID of QCOM8071.
The EMAC also has some complex clock initialization requirements
that are not represented by this patch. This will be addressed
in a future patch.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms. This
change makes it easier to add ACPI support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform_device returned by of_find_device_by_node() is not
automatically released when the driver unprobes. Therefore,
managed calls like devm_ioremap_resource() should not be used.
Instead, we manually allocate the resources and then free them
on driver release.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the first two members of the Renesas RZ/G family, RZ/G1M/E
(also known as R8A7743/5). The Ether core is the same as in the R-Car gen2
SoCs, so will share the code/data with them...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, in order to offload a FIB entry to HW we use switchdev op.
Use the newly introduced FIB notifier infrasturucture to process
FIB entries to offload the in HW.
Abort mechanism is now handled within the rocker driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, in order to offload a FIB entry to HW we use switchdev op.
However that has limits. Mainly in case we need to make the HW aware of
all route prefixes configured in kernel. HW needs to know those in order
to properly trap appropriate packets and pass the to kernel to do
the forwarding. Abort mechanism is now handled within the mlxsw driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a reset occurs, the PPS SYS_WRAP interrupt was not re-enabled which
resulted in disabling of the PPS signaling. Fix this by recording when
the interrupt is on and ensuring that we re-enable it every time we
reset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump igb version to match other igb drivers.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to match other igbvf drivers.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warning:
drivers/net/ethernet/intel/igb/igb_ethtool.c:2707:5: warning:
symbol 'igb_rxnfc_write_vlan_prio_filter' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The group list must be freed prior to freeing the command otherwise
we have a use-after-free.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(1) Modify the register settings for LRO relinquishments
(2) Jump out from the waiting loop while LRO relinquishments are done
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop PDMA while the frame engine is going to stop.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 62469c7600 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c7600 we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c7600, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6b352ebccb ("net: ethernet: broadcom: bcmgenet:
use new api ethtool_{get|set}_link_ksettings").
We needs to revert the commit 62469c7600 ("net: ethernet: bcmgenet:
use phydev from struct net_device"), because this commit add a
regression. As the commit 6b352ebccb ("net: ethernet: broadcom:
bcmgenet: use new api ethtool_{get|set}_link_ksettings") depend
on the first one, we also need to revert it first.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 62469c7600 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c7600 we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c7600, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.
Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:
~/$ cat /proc/cpu/alignment
User: 0
System: 72645 (inet_gro_receive+0x104/0x27c)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 72645
User faults: 3 (fixup+warn)
This patch was suggested by Andrew Lunn in this message to linux-netdev:
http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2
and adapted from a patch by Russell King from 2014:
http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8a
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
