Appears to be fixed with commit:
"drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo"
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
At least on my HP 2540p this is wrong at bootup, fine
at any other time once a lid event has occured. This is due to
_REG vs _INI ordering in the ACPI tables.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
So we used to use lpfn directly to restrict VRAM when we couldn't
access the unmappable area, however this was removed in
93225b0d7b as it also restricted
the gtt placements. However it was only later noticed that this
broke on some hw.
This removes the active_vram_size, and just explicitly sets it
when it changes, TTM/drm_mm will always use the real_vram_size,
and the active vram size will change the TTM size used for lpfn
setting.
We should re-work the fpfn/lpfn to per-placement at some point
I suspect, but that is too late for this kernel.
Hopefully this addresses:
https://bugs.freedesktop.org/show_bug.cgi?id=35254
v2: fix reported useful VRAM size to userspace to be correct.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We've been getting reports of complete system lockups with rv3xx hw on
AGP and PCIE when running gnome-shell or kwin with compositing.
It appears the hw really doesn't like setting these registers while
stuff is running, this moves the setting of the registers into the modeset
since they aren't required to be changed anywhere else.
fixes: https://bugs.freedesktop.org/show_bug.cgi?id=35183
Reported-and-tested-by: Álmos <aaalmosss@gmail.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like these got passed over with both being merged at the same
time but not quite meeting in the middle.
should fix: https://bugs.freedesktop.org/show_bug.cgi?id=34137
along with Michael's phoronix article.
Reported-by: Chi-Thanh Christopher Nguyen
Article-written-by: Michael Larabel @ phoronix
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 951f3512db
drm/i915: Do not handle backlight combination mode specially
since this commit introduced other regressions due to untouched LBPC
register, e.g. the backlight dimmed after resume.
In addition to the revert, this patch includes a fix for the original
issue (weird backlight levels) by removing the wrong bit shift for
computing the current backlight level.
Also, including typo fixes (lpbc -> lbpc).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34524
Acked-by: Indan Zupancic <indan@nul.nu>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* ickle/drm-intel-fixes:
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
The per-vm mutex doesn't prevent this completely, a flush coming from the
BAR VM could potentially happen at the same time as one for the channel
VM. Not to mention that if/when we get per-client/channel VM, this will
happen far more frequently.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TTM assumes an error condition from man->func->get_node() means that
something went horribly wrong, and causes it to bail.
The driver is supposed to return 0, and leave mm_node == NULL to
signal that it couldn't allocate any memory.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some hardware claims to have both an LVDS panel and an eDP output.
Whilst this may be true in a rare case, more often it is just broken
hardware. If we see an eDP device we know that it must be connected and
so we can confirm its existence with a simple probe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34165
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Early gen3 and gen2 chipset do not have the relaxed per-surface tiling
constraints of the later chipsets, so we need to check that the GTT
alignment is correct for the new tiling. If it is not, we need to
rebind.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Andi Kleen narrowed his GPU hangs on his Sugar Bay (SNB desktop) rev 09
down to the use of GPU semaphores, and we already know that they appear
broken up to Huron River (mobile) rev 08. (I'm optimistic that disabling
GPU semaphores is simply hiding another bug by the latency and
side-effects of the additional device interaction it introduces...)
However, use of semaphores is a massive performance improvement... Only
as long as the system remains stable. Enable at your peril.
Reported-by: Andi Kleen <andi-fd@firstfloor.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33921
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.
"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: Matt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit c2e0eb1670.
As it turns out, userspace already depends upon being able to enable
tiling on existing bo which it promises to be large enough for its
purposes i.e. it will not access beyond the end of the last full-tile
row.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35016
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We're coming to see a need to have a set of generic capability checks in
the core DRM, in addition to the driver-specific ioctls that already
exist.
This patch defines an ioctl to do as such, but does not yet define any
capabilities.
[airlied: drop the driver callback for now.]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The nv30/nv40 3d driver is about to start using DMA_FENCE from the 3D
object which, it turns out, doesn't like its DMA object to not be
aligned to a 4KiB boundary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
hdmi 1.3 raises the max clock from 165 Mhz to 340 Mhz.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These should be handled by the clear_state setup, but set them
directly as well just to be sure.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman is different enough from evergreen to warrant it's own functions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman asics have 3 ring buffers:
ring 0 supports both gfx and compute
rings 1 and 2 are compute only
At the moment we only support ring 0.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch sets up the gart in legacy mode. We
probably want to switch to full VM mode at some point.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MC ucode is no longer loaded by the vbios
tables as on previous asics. It now must be loaded
by the driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman is DCE5 display plus a new 4-way shader block.
3D state programming is similar to evergreen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's cleaned before saving and re-initialized after restoring.
So don't need to save/restore it. And also new chip has new address
for hardware status page register, don't write to old address.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On a Thinkpad x61s, I noticed some memory corruption when
plugging/unplugging the external VGA connection. The symptoms are that
4 bytes at the beginning of a page get overwritten by zeroes.
The address of the corruption varies when rebooting the machine, but
stays constant while it's running (so it's possible to repeatedly write
some data and then corrupt it again by plugging the cable).
Further investigation revealed that the corrupted address is
(dev_priv->status_page_dmah->busaddr & 0xffffffff), ie. the beginning of
the hardware status page of the i965 graphics card, cut to 32 bits.
So it seems that for some memory access, the hardware uses only 32 bit
addressing. If the hardware status page is located >4GB, this
corrupts unrelated memory.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This seems to be running stably on my test laptop, so hopefully the
reported hangs where just symptoms of other bugs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I stumbled over this magic bit in the gen3 INSTPM:
Bit11 Interrupt-Based AGPBUSY# Enable:
‘0’ = Pending GMCH interrupts will not cause AGPBUSY# assertion.
‘1’ = Pending GMCH interrupts will cause AGPBUSY# assertion and hence
can cause the CPU to exit C3. There is no suppression of cacheable
writes.
Note that in either case in C3 the interrupts are not lost. They will be
forwarded to the ICH when the GMCH is out of C3.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Using PM latency request turns out to be very fragile and only works for
some systems, depending upon the ACPI implementation. However, I've
stumbled across a promising bit in INSTPM: "Interrupt-Based AGPBUSY#".
This reverts commit b0b544cd37.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Userspace has a legitimate requirement to use a delta that points to
outside of the target bo, and so we need to enable this. (As this is an
abi break, albeit a relaxation of the current restrictions, mark the change
with a new flag.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drivers/gpu/drm/i915/i915_irq.c: In function ‘ironlake_irq_postinstall’:
drivers/gpu/drm/i915/i915_irq.c:1618: warning: unused variable ‘pipe’
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Somehow fixes a misrendering + hang at GDM startup on my NVA8...
My first guess would have been stale TLB entries laying around that a new
bo then accidentally inherits. That doesn't make a great deal of sense
however, as when we mapped the pages for the new bo the TLBs would've
gotten flushed anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
have to read values from the IB in order as we could cross
a page boundary at any time and won't be able to go backwards.
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are a bunch of off by one errors in the sanity checks here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The immediate benefit of doing this is that on NV50 and up, the GPU
virtual address of any buffer is now constant, regardless of what
memtype they're placed in.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds a table of known nvc0 memtypes, and modifies the validity check
to allow any non-compressed type. Support for Z compression will come at
a later point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Upcoming patches are going to enable full support for buffers that keep
a constant GPU virtual address whenever they're validated for use by
the GPU.
In order for this to work properly while keeping support for large pages,
we need to know if it's ever going to be possible for a buffer to end
up in GART, and if so, disable large pages for the buffer's VMA.
This is a new restriction that's not present in earlier kernel's, but
should not break userspace as the current code never attempts to validate
buffers into a memtype other than it was created with.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
'mappable' isn't really used at all, nor is it necessary anymore as the
bo code is capable of moving buffers to mappable vram as required.
'no_vm' isn't necessary anymore either, any places that don't want to be
mapped into a GPU address space should allocate the VRAM directly instead.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The code was supposed to print registers around 0x405018 (which is read
earlier), not 0x405818.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The hw doesn't really appear to be designed to be used the way we have to
use it due to DRI2's design. This leads us to having to keep the flipped
fb support active at all times.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Also imports a couple of helper functions that'll be used to implement
page flipping in the following commits..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This should prevent a number of races from occuring, the most obvious of
which will be exposed when we start making use of the "display sync" evo
channel for page flipping. The DS channel will reject any command stream
that doesn't completely agree with the current "master" state.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to be able to have the bh run while possibly spinning waiting for
the EVO notifier to signal. This apparently happens in some circumstances
with preempt disabled, so our workqueue was never being run.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The nv50 display isr bh needs to be converted to a tasklet, which means
we can't sleep anymore. The places we execute vbios init tables are
rare, and not in any way performance critical, so this isn't a huge
problem.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With cmwq, there's no reason for nouveau to use a dedicated workqueue.
Drop dev_priv->wq and use system_wq instead. Each work item is sync
flushed when the containing structure is unregistered/destroyed.
Note that this change also makes sure that nv50_gpio_handler is not
freed while the contained work item is still running.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This gives a small, but noticeable performance gain at lower performance
levels, and unchanged at the higher ones.
With this commit, we're now using the same timeslice size as the NVIDIA
binary driver currently does, and dropping an unknown bit that NVIDIA
no longer appear to set.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We may well be making more use of semaphores in the future, having the
entire VM available makes requiring DMA objects for each and every
semaphore block unnecessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
And also, don't disable PFIFO IRQs completely whenever we recieve one,
just when we don't know about it already.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
These are the same semaphores nvc0 will use, and they potentially allow
us to do much cooler things than our current inter-channel sync impl.
Lets switch to them where possible now for some testing.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In preparation for the addition of a new nv40 backend, we'll need to be
able to distinguish between a paged dma object and the on-chip GART.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
After disabling, we're meant to teardown the bo used for the contexts,
not recurse into ourselves again and preventing module unload.
Reported-and-tested-by: Ben Widawsky <bwidawsk@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: fix corruptions on i8xx due to relaxed fencing
drm/i915: skip FDI & PCH enabling for DP_A
agp/intel: Experiment with a 855GM GWB bit
drm/i915: don't enable FDI & transcoder interrupts after all
drm/i915: Ignore a hung GPU when flushing the framebuffer prior to a switch
It looks like gen2 has a peculiar interleaved 2-row inter-tile
layout. Probably inherited from i81x which had 2kb tiles (which
naturally fit an even-number-of-tile-rows scheme to fit onto 4kb
pages). There is no other mention of this in any docs (also not
in the Intel internal documention according to Chris Wilson).
Problem manifests itself in corruptions in the second half of the
last tile row (if the bo has an odd number of tiles). Which can
only happen with relaxed tiling (introduced in a00b10c360).
So reject set_tiling calls that don't satisfy this constrain to
prevent broken userspace from causing havoc. While at it, also
check the size for newer chipsets.
LKML: https://lkml.org/lkml/2011/2/19/5
Reported-by: Indan Zupancic <indan@nul.nu>
Tested-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 5a893fc28f.
This causes a use after free in the ttm free alloc pages path,
when it tries to get the be after the be has been destroyed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'stable/ttm.pci-api.v5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
ttm: Include the 'struct dev' when using the DMA API.
nouveau/ttm/PCIe: Use dma_addr if TTM has set it.
radeon/ttm/PCIe: Use dma_addr if TTM has set it.
ttm: Expand (*populate) to support an array of DMA addresses.
ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set.
ttm: Introduce a placeholder for DMA (bus) addresses.
Using an order 19 drm_ht for the mmap offsets is a little obscene. That
means that will a fully populated GTT with every single object mmaped at
least once in its lifetime, there will be exactly one object in each
bucket.
Typically systems only have at most a few thousand objects, though you
may see a KDE desktop hit 50000. And most of those should never be
mapped... On my systems, just using an order 10 ht would still have an
average occupancy less than 1, so apply a small safety factor and
use an order 12 ht, like the other mmap offset ht.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
... and fixup some methods to accept the constant argument.
Now that constant module arrays are loaded into read-only memory, using
const appropriately has some benefits beyond warning the programmer
about likely mistakes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
the texture checking code didn't work for block formats like s3tc,
this overhauls it to work for all types.
v2: add texture array support.
v3: add subsampled formats
Signed-off-by: Dave Airlie <airlied@redhat.com>
Nouveau doesn't have enough information at ttm_backend_func.bind() time
to implement things like tiled GART, or to keep a buffer at a constant
address in the GPU virtual address space no matter where in physical
memory it's placed.
To resolve this, nouveau will handle binding of all buffers to the GPU
itself from the move_notify() hook. This commit ensures it's called
for all buffer moves.
Talked to Dave about the impact on radeon, which uses move_notify, it
doesn't look like anything should break there.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Thomas Hellstrom <thomas@shipmail.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there is an alpha channel, need to mask in 1's in the alpha channel
to prevent the fb from being completely transparent.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now all the asic specific stuff ist mostly hid in radeon_asic.*
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
... and switch it to container_of upcasting.
v2: converted new pageflip code-paths.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unconditionally initialize the drm gem object - it's not
worth the trouble not to for the few kernel objects.
This patch only changes the place of the drm gem object,
access is still done via pointers.
v2: Uncoditionally align the size in radeon_bo_create. At
least the r600/evergreen blit code didn't to this, angering
the paranoid gem code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the switch to implicit free space accounting one pointer
got unused when scanning. Use it to create a single-linked list
to ensure correct unwinding of the scan state.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old api has a two-step process: First search for a suitable
free hole, then allocate from that specific hole. No user used
this to do anything clever. So drop it for the embeddable variant
of the drm_mm api (the old one retains this ability, for the time
being).
With struct drm_mm_node embedded, we cannot track allocations
anymore by checking for a NULL pointer. So keep track of this
and add a small helper drm_mm_node_allocated.
Also add a function to move allocations between different struct
drm_mm_node.
v2: Implement suggestions by Chris Wilson.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The idea is to track free holes implicitly by marking the allocation
immediatly preceeding a hole.
To avoid an ugly corner case add a dummy head_node to struct drm_mm
to track the hole that spans to complete allocation area when the
memory manager is empty.
To guarantee that there's always a preceeding/following node (that might
be marked as hole_follows == 1), move the mm->node_list list_head to the
head_node.
The main allocator and fair-lru scan code actually becomes simpler.
Only the debug code slightly suffers because free areas are no longer
explicit.
Also add drm_mm_for_each_node (which will be much more useful when
struct drm_mm_node is embeddable).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Nouveau was checking drm_mm internals on teardown to see whether the
memory manager was initialized. Hide these internals in a small
inline helper function.
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some userspaces can emit a whole packet without disabling AA resolve
by the looks of it, so we have to deal with them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: Jorg Otte <jrg.otte@googlemail.com>
r100_gpu_init() was dropped in 90aca4d ("drm/radeon/kms: simplify &
improve GPU reset V2") but here it was only commented out.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Testing showed the current code can already handle doublescan
video modes just fine. A trivial tweak makes it work for interlaced
scanout as well.
Tested and shown to be precise on Radeon rv530, r600 and
Intel 945-GME.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Documentation/atomic_ops.txt tells us that there are memory
barriers optimized for atomic_inc and other atomic_t ops.
Use these instead of smp_wmb(), and also to make the required
memory barriers around vblank counter increments more explicit.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use of abs() wrongly wrapped diff_ns to 32 bit, which gives a 1/4000
probability of a missed vblank increment at each vblank irq reenable
if the kms driver doesn't support high precision vblank timestamping.
Not a big deal in practice, but let's make it nice.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this aligns the height of the fb allocation so it doesn't trip
over the size checks later when we use this from userspace to
copy the buffer at X start.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit a6f9761743.
Remove this commit as it is no longer necessary. The relevant bugs
were fixed properly in:
drm/radeon/kms: hopefully fix pll issues for real (v3)
5b40ddf888
drm/radeon/kms: add missing frac fb div flag for dce4+
9f4283f49f
This commit also broke certain ~5 Mhz modes on old arcade monitors,
so reverting this commit fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29502
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes the accounting when using 'debug_dma_dump_mappings()'
and CONFIG_DMA_API_DEBUG=y be assigned to the correct device
instead of 'fallback'.
No functional change - just cosmetic.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Merge in the conflicting eDP fix.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to prevent "crushed blacks" on TVs, the range of the RGB output
may be limited to 16-235. This used to be available through Xorg under
the "Broadcast RGB" option, so reintroduce support for KMS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34543
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The code paths for modesetting are growing in complexity as we may need
to move the buffers around in order to fit the scanout in the aperture.
Therefore we face a choice as to whether to thread the interruptible status
through the entire pinning and unbinding code paths or to add a flag to
the device when we may not be interrupted by a signal. This does the
latter and so fixes a few instances of modesetting failures under stress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we just need a temporary array whilst performing the relocations for
the execbuffer, first attempt to allocate using kmalloc even if it is
not of order page-0. This avoids the overhead of remapping the
discontiguous array and so gives a moderate boost to execution
throughput.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Seems like we are forever to be cursed with buggy firmware, so allow the
user to explicitly set the panel connection status.
Of secondary utility for cases where I run laptops with the lid closed,
but still want to configure the LVDS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dave Airlie spotted that we had a potential bug should we ever rearrange
the drm_i915_gem_object so not the base drm_gem_object was not its first
member. He noticed that we often convert the return of
drm_gem_object_lookup() immediately into drm_i915_gem_object and then
check the result for nullity. This is only valid when the base object is
the first member and so the superobject has the same address. Play safe
instead and use the compiler to convert back to the original return
address for sanity testing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In a few places I replaced reads of per-pipe registers with the actual
register offsets themselves (converting I915_READ(reg) to _PIPE(reg)).
Alexey caught this on his 9xx machine because the cursor control write
was affected. A quick audit showed a few more places where I'd borked
a read, so here's a patch to fix things up.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: compilation fix]
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 633f2ea266 and the
attempted fix dcbe6f2b3d.
There is a single clock source used for both SSC (some LVDS and DP) and
non-SSC (VGA, DVI) outputs. So we need to be careful to only enable SSC
as necessary. However, fiddling with DREFCLK was causing DP links to be
dropped and we do not have a fix ready, so revert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems. So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can enable some safely, but FDI and transcoder interrupts can occur
and block other interrupts from being detected (like port hotplug
events). So keep them disabled by default (they can be re-enabled for
debugging display bringup, but should generally be off).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The current code does not follow Intel documentation: It misses some things
and does other, undocumented things. This causes wrong backlight values in
certain conditions. Instead of adding tricky code handling badly documented
and rare corner cases, don't handle combination mode specially at all. This
way PCI_LBPC is never touched and weird things shouldn't happen.
If combination mode is enabled, then the only downside is that changing the
brightness has a greater granularity (the LBPC value), but LBPC is at most
254 and the maximum is in the thousands, so this is no real functional loss.
A potential problem with not handling combined mode is that a brightness of
max * PCI_LBPC is not bright enough. However, this is very unlikely because
from the documentation LBPC seems to act as a scaling factor and doesn't look
like it's supposed to be changed after boot. The value at boot should always
result in a bright enough screen.
IMPORTANT: However, although usually the above is true, it may not be when
people ran an older (2.6.37) kernel which messed up the LBPC register, and
they are unlucky enough to have a BIOS that saves and restores the LBPC value.
Then a good kernel may seem to not work: Max brightness isn't bright enough.
If this happens people should boot back into the old kernel, set brightness
to the maximum, and then reboot. After that everything should be fine.
For more information see the below links. This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=23472http://bugzilla.kernel.org/show_bug.cgi?id=25072
Signed-off-by: Indan Zupancic <indan@nul.nu>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the TTM layer has used the DMA API to setup pages that are
TTM_PAGE_FLAG_DMA32 (look at patch titled: "ttm: Utilize the
DMA API for pages that have TTM_PAGE_FLAG_DMA32 set"), lets
use it when programming the GART in the PCIe type cards.
This patch skips doing the pci_map_page (and pci_unmap_page) if
there is a DMA addresses passed in for that page. If the dma_address
is zero (or DMA_ERROR_CODE), then we continue on with our old
behaviour.
[v2: Added a review-by tag]
Reviewed-by: Thomas Hellstrom <thomas@shipmail.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Ian Campbell <ian.campbell@citrix.com>
If the TTM layer has used the DMA API to setup pages that are
TTM_PAGE_FLAG_DMA32 (look at patch titled: "ttm: Utilize the dma_addr_t
array for pages that are to in DMA32 pool."), lets use it
when programming the GART in the PCIe type cards.
This patch skips doing the pci_map_page (and pci_unmap_page) if
there is a DMA addresses passed in for that page. If the dma_address
is zero (or DMA_ERROR_CODE), then we continue on with our old
behaviour.
[v2: Fixed an indentation problem, added reviewed-by tag]
[v3: Added Acked-by Jerome]
Acked-by: Jerome Glisse <j.glisse@gmail.com>
Reviewed-by: Thomas Hellstrom <thomas@shipmail.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Ian Campbell <ian.campbell@citrix.com>
* 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix suspend/resume on GPUs that don't have PM support
drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
drm/nv40: fix tiling-related setup for a number of chipsets
drm/nouveau: fix non-EDIDful native mode selection
drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+. Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
