* Clean up vCPU targets, always returning generic v8 as the preferred target
* Trap forwarding infrastructure for nested virtualization (used for traps
that are taken from an L2 guest and are needed by the L1 hypervisor)
* FEAT_TLBIRANGE support to only invalidate specific ranges of addresses
when collapsing a table PTE to a block PTE. This avoids that the guest
refills the TLBs again for addresses that aren't covered by the table PTE.
* Fix vPMU issues related to handling of PMUver.
* Don't unnecessary align non-stack allocations in the EL2 VA space
* Drop HCR_VIRT_EXCP_MASK, which was never used...
* Don't use smp_processor_id() in kvm_arch_vcpu_load(),
but the cpu parameter instead
* Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort()
* Remove prototypes without implementations
RISC-V:
* Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest
* Added ONE_REG interface for SATP mode
* Added ONE_REG interface to enable/disable multiple ISA extensions
* Improved error codes returned by ONE_REG interfaces
* Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V
* Added get-reg-list selftest for KVM RISC-V
s390:
* PV crypto passthrough enablement (Tony, Steffen, Viktor, Janosch)
Allows a PV guest to use crypto cards. Card access is governed by
the firmware and once a crypto queue is "bound" to a PV VM every
other entity (PV or not) looses access until it is not bound
anymore. Enablement is done via flags when creating the PV VM.
* Guest debug fixes (Ilya)
x86:
* Clean up KVM's handling of Intel architectural events
* Intel bugfixes
* Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use debug
registers and generate/handle #DBs
* Clean up LBR virtualization code
* Fix a bug where KVM fails to set the target pCPU during an IRTE update
* Fix fatal bugs in SEV-ES intrahost migration
* Fix a bug where the recent (architecturally correct) change to reinject
#BP and skip INT3 broke SEV guests (can't decode INT3 to skip it)
* Retry APIC map recalculation if a vCPU is added/enabled
* Overhaul emergency reboot code to bring SVM up to par with VMX, tie the
"emergency disabling" behavior to KVM actually being loaded, and move all of
the logic within KVM
* Fix user triggerable WARNs in SVM where KVM incorrectly assumes the TSC
ratio MSR cannot diverge from the default when TSC scaling is disabled
up related code
* Add a framework to allow "caching" feature flags so that KVM can check if
the guest can use a feature without needing to search guest CPUID
* Rip out the ancient MMU_DEBUG crud and replace the useful bits with
CONFIG_KVM_PROVE_MMU
* Fix KVM's handling of !visible guest roots to avoid premature triple fault
injection
* Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the API surface
that is needed by external users (currently only KVMGT), and fix a variety
of issues in the process
This last item had a silly one-character bug in the topic branch that
was sent to me. Because it caused pretty bad selftest failures in
some configurations, I decided to squash in the fix. So, while the
exact commit ids haven't been in linux-next, the code has (from the
kvm-x86 tree).
Generic:
* Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier events to pass
action specific data without needing to constantly update the main handlers.
* Drop unused function declarations
Selftests:
* Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs
* Add support for printf() in guest code and covert all guest asserts to use
printf-based reporting
* Clean up the PMU event filter test and add new testcases
* Include x86 selftests in the KVM x86 MAINTAINERS entry
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT1m0kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMNgggAiN7nz6UC423FznuI+yO3TLm8tkx1
CpKh5onqQogVtchH+vrngi97cfOzZb1/AtifY90OWQi31KEWhehkeofcx7G6ERhj
5a9NFADY1xGBsX4exca/VHDxhnzsbDWaWYPXw5vWFWI6erft9Mvy3tp1LwTvOzqM
v8X4aWz+g5bmo/DWJf4Wu32tEU6mnxzkrjKU14JmyqQTBawVmJ3RYvHVJ/Agpw+n
hRtPAy7FU6XTdkmq/uCT+KUHuJEIK0E/l1js47HFAqSzwdW70UDg14GGo1o4ETxu
RjZQmVNvL57yVgi6QU38/A0FWIsWQm5IlaX1Ug6x8pjZPnUKNbo9BY4T1g==
=W+4p
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- Clean up vCPU targets, always returning generic v8 as the preferred
target
- Trap forwarding infrastructure for nested virtualization (used for
traps that are taken from an L2 guest and are needed by the L1
hypervisor)
- FEAT_TLBIRANGE support to only invalidate specific ranges of
addresses when collapsing a table PTE to a block PTE. This avoids
that the guest refills the TLBs again for addresses that aren't
covered by the table PTE.
- Fix vPMU issues related to handling of PMUver.
- Don't unnecessary align non-stack allocations in the EL2 VA space
- Drop HCR_VIRT_EXCP_MASK, which was never used...
- Don't use smp_processor_id() in kvm_arch_vcpu_load(), but the cpu
parameter instead
- Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort()
- Remove prototypes without implementations
RISC-V:
- Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest
- Added ONE_REG interface for SATP mode
- Added ONE_REG interface to enable/disable multiple ISA extensions
- Improved error codes returned by ONE_REG interfaces
- Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V
- Added get-reg-list selftest for KVM RISC-V
s390:
- PV crypto passthrough enablement (Tony, Steffen, Viktor, Janosch)
Allows a PV guest to use crypto cards. Card access is governed by
the firmware and once a crypto queue is "bound" to a PV VM every
other entity (PV or not) looses access until it is not bound
anymore. Enablement is done via flags when creating the PV VM.
- Guest debug fixes (Ilya)
x86:
- Clean up KVM's handling of Intel architectural events
- Intel bugfixes
- Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use
debug registers and generate/handle #DBs
- Clean up LBR virtualization code
- Fix a bug where KVM fails to set the target pCPU during an IRTE
update
- Fix fatal bugs in SEV-ES intrahost migration
- Fix a bug where the recent (architecturally correct) change to
reinject #BP and skip INT3 broke SEV guests (can't decode INT3 to
skip it)
- Retry APIC map recalculation if a vCPU is added/enabled
- Overhaul emergency reboot code to bring SVM up to par with VMX, tie
the "emergency disabling" behavior to KVM actually being loaded,
and move all of the logic within KVM
- Fix user triggerable WARNs in SVM where KVM incorrectly assumes the
TSC ratio MSR cannot diverge from the default when TSC scaling is
disabled up related code
- Add a framework to allow "caching" feature flags so that KVM can
check if the guest can use a feature without needing to search
guest CPUID
- Rip out the ancient MMU_DEBUG crud and replace the useful bits with
CONFIG_KVM_PROVE_MMU
- Fix KVM's handling of !visible guest roots to avoid premature
triple fault injection
- Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the
API surface that is needed by external users (currently only
KVMGT), and fix a variety of issues in the process
Generic:
- Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier
events to pass action specific data without needing to constantly
update the main handlers.
- Drop unused function declarations
Selftests:
- Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs
- Add support for printf() in guest code and covert all guest asserts
to use printf-based reporting
- Clean up the PMU event filter test and add new testcases
- Include x86 selftests in the KVM x86 MAINTAINERS entry"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (279 commits)
KVM: x86/mmu: Include mmu.h in spte.h
KVM: x86/mmu: Use dummy root, backed by zero page, for !visible guest roots
KVM: x86/mmu: Disallow guest from using !visible slots for page tables
KVM: x86/mmu: Harden TDP MMU iteration against root w/o shadow page
KVM: x86/mmu: Harden new PGD against roots without shadow pages
KVM: x86/mmu: Add helper to convert root hpa to shadow page
drm/i915/gvt: Drop final dependencies on KVM internal details
KVM: x86/mmu: Handle KVM bookkeeping in page-track APIs, not callers
KVM: x86/mmu: Drop @slot param from exported/external page-track APIs
KVM: x86/mmu: Bug the VM if write-tracking is used but not enabled
KVM: x86/mmu: Assert that correct locks are held for page write-tracking
KVM: x86/mmu: Rename page-track APIs to reflect the new reality
KVM: x86/mmu: Drop infrastructure for multiple page-track modes
KVM: x86/mmu: Use page-track notifiers iff there are external users
KVM: x86/mmu: Move KVM-only page-track declarations to internal header
KVM: x86: Remove the unused page-track hook track_flush_slot()
drm/i915/gvt: switch from ->track_flush_slot() to ->track_remove_region()
KVM: x86: Add a new page-track hook to handle memslot deletion
drm/i915/gvt: Don't bother removing write-protection on to-be-deleted slot
KVM: x86: Reject memslot MOVE operations if KVMGT is attached
...
Use bpf_jit_binary_pack_alloc() for memory management of JIT binaries in
RISCV BPF JIT. The bpf_jit_binary_pack_alloc creates a pair of RW and RX
buffers. The JIT writes the program into the RW buffer. When the JIT is
done, the program is copied to the final RX buffer with
bpf_jit_binary_pack_finalize.
Implement bpf_arch_text_copy() and bpf_arch_text_invalidate() for RISCV
JIT as these functions are required by bpf_jit_binary_pack allocator.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Song Liu <song@kernel.org>
Reviewed-by: Pu Lehui <pulehui@huawei.com>
Acked-by: Björn Töpel <bjorn@kernel.org>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20230831131229.497941-5-puranjay12@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The BPF JIT needs to write invalid instructions to RX regions of memory to
invalidate removed BPF programs. This needs a function like memset() that
can work with RX memory.
Implement patch_text_set_nosync() which is similar to text_poke_set() of
x86.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Pu Lehui <pulehui@huawei.com>
Acked-by: Björn Töpel <bjorn@kernel.org>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20230831131229.497941-4-puranjay12@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The patch_insn_write() function currently doesn't work for multiple pages
of instructions, therefore patch_text_nosync() will fail with a page fault
if called with lengths spanning multiple pages.
This commit extends the patch_insn_write() function to support multiple
pages by copying at max 2 pages at a time in a loop. This implementation
is similar to text_poke_copy() function of x86.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Pu Lehui <pulehui@huawei.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20230831131229.497941-3-puranjay12@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
We can now use arm64 functions to handle the move of the kernel physical
mapping: if KASLR is enabled, we will try to get a random seed from the
firmware, if not possible, the kernel will be moved to a location that
suits its alignment constraints.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Song Shuai <songshuaishuai@tinylab.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20230722123850.634544-6-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Dump out the KASLR virtual kernel offset when panic to help debug kernel.
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Song Shuai <songshuaishuai@tinylab.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20230722123850.634544-3-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
KASLR implementation relies on a relocatable kernel so that we can move
the kernel mapping.
The seed needed to virtually move the kernel is taken from the device tree,
so we rely on the bootloader to provide a correct seed. Zkr could be used
unconditionnally instead if implemented, but that's for another patch.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Song Shuai <songshuaishuai@tinylab.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20230722123850.634544-2-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
- Enable -Wenum-conversion warning option
- Refactor the rpm-pkg target
- Fix scripts/setlocalversion to consider annotated tags for rt-kernel
- Add a jump key feature for the search menu of 'make nconfig'
- Support Qt6 for 'make xconfig'
- Enable -Wformat-overflow, -Wformat-truncation, -Wstringop-overflow, and
-Wrestrict warnings for W=1 builds
- Replace <asm/export.h> with <linux/export.h> for alpha, ia64, and sparc
- Support DEB_BUILD_OPTIONS=parallel=N for the debian source package
- Refactor scripts/Makefile.modinst and fix some modules_sign issues
- Add a new Kconfig env variable to warn symbols that are not defined anywhere
- Show help messages of config fragments in 'make help'
-----BEGIN PGP SIGNATURE-----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=lfUi
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Enable -Wenum-conversion warning option
- Refactor the rpm-pkg target
- Fix scripts/setlocalversion to consider annotated tags for rt-kernel
- Add a jump key feature for the search menu of 'make nconfig'
- Support Qt6 for 'make xconfig'
- Enable -Wformat-overflow, -Wformat-truncation, -Wstringop-overflow,
and -Wrestrict warnings for W=1 builds
- Replace <asm/export.h> with <linux/export.h> for alpha, ia64, and
sparc
- Support DEB_BUILD_OPTIONS=parallel=N for the debian source package
- Refactor scripts/Makefile.modinst and fix some modules_sign issues
- Add a new Kconfig env variable to warn symbols that are not defined
anywhere
- Show help messages of config fragments in 'make help'
* tag 'kbuild-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (62 commits)
kconfig: fix possible buffer overflow
kbuild: Show marked Kconfig fragments in "help"
kconfig: add warn-unknown-symbols sanity check
kbuild: dummy-tools: make MPROFILE_KERNEL checks work on BE
Documentation/llvm: refresh docs
modpost: Skip .llvm.call-graph-profile section check
kbuild: support modules_sign for external modules as well
kbuild: support 'make modules_sign' with CONFIG_MODULE_SIG_ALL=n
kbuild: move more module installation code to scripts/Makefile.modinst
kbuild: reduce the number of mkdir calls during modules_install
kbuild: remove $(MODLIB)/source symlink
kbuild: move depmod rule to scripts/Makefile.modinst
kbuild: add modules_sign to no-{compiler,sync-config}-targets
kbuild: do not run depmod for 'make modules_sign'
kbuild: deb-pkg: support DEB_BUILD_OPTIONS=parallel=N in debian/rules
alpha: remove <asm/export.h>
alpha: replace #include <asm/export.h> with #include <linux/export.h>
ia64: remove <asm/export.h>
ia64: replace #include <asm/export.h> with #include <linux/export.h>
sparc: remove <asm/export.h>
...
Currently the Kconfig fragments in kernel/configs and arch/*/configs
that aren't used internally aren't discoverable through "make help",
which consists of hard-coded lists of config fragments. Instead, list
all the fragment targets that have a "# Help: " comment prefix so the
targets can be generated dynamically.
Add logic to the Makefile to search for and display the fragment and
comment. Add comments to fragments that are intended to be direct targets.
Signed-off-by: Kees Cook <keescook@chromium.org>
Co-developed-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This patch add back the ptrace support with the following fix:
- Define NT_RISCV_CSR and re-number NT_RISCV_VECTOR to prevent
conflicting with gdb's NT_RISCV_CSR.
- Use struct __riscv_v_regset_state to handle ptrace requests
Since gdb does not directly include the note description header in
Linux and has already defined NT_RISCV_CSR as 0x900, we decide to
sync with gdb and renumber NT_RISCV_VECTOR to solve and prevent future
conflicts.
Fixes: 0c59922c76 ("riscv: Add ptrace vector support")
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Link: https://lore.kernel.org/r/20230825050248.32681-1-andy.chiu@sifive.com
[Palmer: Drop the unused "size" variable in riscv_vr_set().]
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Introduce support for nonstandard noncoherent systems in the RISC-V
architecture. It enables function pointer support to handle cache
management in such systems.
This patch adds a new configuration option called
"RISCV_NONSTANDARD_CACHE_OPS." This option is a boolean flag that
depends on "RISCV_DMA_NONCOHERENT" and enables the function pointer
support for cache management in nonstandard noncoherent systems.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com> # tyre-kicking on a d1
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> #
Link: https://lore.kernel.org/r/20230818135723.80612-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add required ports of the Alternative scheme for Andes CPU cores.
I/O Coherence Port (IOCP) provides an AXI interface for connecting external
non-caching masters, such as DMA controllers. IOCP is a specification
option and is disabled on the Renesas RZ/Five SoC due to this reason cache
management needs a software workaround.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com> # tyre-kicking on a d1
Link: https://lore.kernel.org/r/20230818135723.80612-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add helper functions for cache wback/inval/clean and use them
arch_sync_dma_for_device()/arch_sync_dma_for_cpu() functions. The proposed
changes are in preparation for switching over to generic implementation.
Reorganization of the code is based on the patch (Link[0]) from Arnd.
For now I have dropped CONFIG_ARCH_HAS_SYNC_DMA_FOR_CPU check as this
will be enabled by default upon selection of RISCV_DMA_NONCOHERENT
and also dropped arch_dma_mark_dcache_clean().
Link[0]: https://lore.kernel.org/all/20230327121317.4081816-22-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20230816232336.164413-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
For a DMA_BIDIRECTIONAL transfer, the caches have to be cleaned
first to let the device see data written by the CPU, and invalidated
after the transfer to let the CPU see data written by the device.
riscv also invalidates the caches before the transfer, which does
not appear to serve any purpose.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20230816232336.164413-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
No other architecture intentionally writes back dirty cache lines into
a buffer that a device has just finished writing into. If the cache is
clean, this has no effect at all, but if a cacheline in the buffer has
actually been written by the CPU, there is a driver bug that is likely
made worse by overwriting that buffer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20230816232336.164413-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Now that we're testing unaligned memory copy and making that
determination generically, there are no more users of the vendor
feature_probe_func(). While I think it's probably going to need to come
back, there are no users right now, so let's remove it until it's
needed.
Signed-off-by: Evan Green <evan@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230818194136.4084400-3-evan@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Rather than deferring unaligned access speed determinations to a vendor
function, let's probe them and find out how fast they are. If we
determine that an unaligned word access is faster than N byte accesses,
mark the hardware's unaligned access as "fast". Otherwise, we mark
accesses as slow.
The algorithm itself runs for a fixed amount of jiffies. Within each
iteration it attempts to time a single loop, and then keeps only the best
(fastest) loop it saw. This algorithm was found to have lower variance from
run to run than my first attempt, which counted the total number of
iterations that could be done in that fixed amount of jiffies. By taking
only the best iteration in the loop, assuming at least one loop wasn't
perturbed by an interrupt, we eliminate the effects of interrupts and
other "warm up" factors like branch prediction. The only downside is it
depends on having an rdtime granular and accurate enough to measure a
single copy. If we ever manage to complete a loop in 0 rdtime ticks, we
leave the unaligned setting at UNKNOWN.
There is a slight change in user-visible behavior here. Previously, all
boards except the THead C906 reported misaligned access speed of
UNKNOWN. C906 reported FAST. With this change, since we're now measuring
misaligned access speed on each hart, all RISC-V systems will have this
key set as either FAST or SLOW.
Currently, we don't have a way to confidently measure the difference between
SLOW and EMULATED, so we label anything not fast as SLOW. This will
mislabel some systems that are actually EMULATED as SLOW. When we get
support for delegating misaligned access traps to the kernel (as opposed
to the firmware quietly handling it), we can explicitly test in Linux to
see if unaligned accesses trap. Those systems will start to report
EMULATED, though older (today's) systems without that new SBI mechanism
will continue to report SLOW.
I've updated the documentation for those hwprobe values to reflect
this, specifically: SLOW may or may not be emulated by software, and FAST
represents means being faster than equivalent byte accesses. The change
in documentation is accurate with respect to both the former and current
behavior.
Signed-off-by: Evan Green <evan@rivosinc.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230818194136.4084400-2-evan@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
* Support for the new "riscv,isa-extensions" and "riscv,isa-base" device
tree interfaces for probing extensions.
* Support for userspace access to the performance counters.
* Support for more instructions in kprobes.
* Crash kernels can be allocated above 4GiB.
* Support for KCFI.
* Support for ELFs in !MMU configurations.
* ARCH_KMALLOC_MINALIGN has been reduced to 8.
* mmap() defaults to sv48-sized addresses, with longer addresses hidden
behind a hint (similar to Arm and Intel).
* Also various fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=/tXb
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.6-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for the new "riscv,isa-extensions" and "riscv,isa-base"
device tree interfaces for probing extensions
- Support for userspace access to the performance counters
- Support for more instructions in kprobes
- Crash kernels can be allocated above 4GiB
- Support for KCFI
- Support for ELFs in !MMU configurations
- ARCH_KMALLOC_MINALIGN has been reduced to 8
- mmap() defaults to sv48-sized addresses, with longer addresses hidden
behind a hint (similar to Arm and Intel)
- Also various fixes and cleanups
* tag 'riscv-for-linus-6.6-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (51 commits)
lib/Kconfig.debug: Restrict DEBUG_INFO_SPLIT for RISC-V
riscv: support PREEMPT_DYNAMIC with static keys
riscv: Move create_tmp_mapping() to init sections
riscv: Mark KASAN tmp* page tables variables as static
riscv: mm: use bitmap_zero() API
riscv: enable DEBUG_FORCE_FUNCTION_ALIGN_64B
riscv: remove redundant mv instructions
RISC-V: mm: Document mmap changes
RISC-V: mm: Update pgtable comment documentation
RISC-V: mm: Add tests for RISC-V mm
RISC-V: mm: Restrict address space for sv39,sv48,sv57
riscv: enable DMA_BOUNCE_UNALIGNED_KMALLOC for !dma_coherent
riscv: allow kmalloc() caches aligned to the smallest value
riscv: support the elf-fdpic binfmt loader
binfmt_elf_fdpic: support 64-bit systems
riscv: Allow CONFIG_CFI_CLANG to be selected
riscv/purgatory: Disable CFI
riscv: Add CFI error handling
riscv: Add ftrace_stub_graph
riscv: Add types to indirectly called assembly functions
...
Convert IBT selftest to asm to fix objtool warning
-----BEGIN PGP SIGNATURE-----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=3UUm
-----END PGP SIGNATURE-----
Merge tag 'x86_shstk_for_6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 shadow stack support from Dave Hansen:
"This is the long awaited x86 shadow stack support, part of Intel's
Control-flow Enforcement Technology (CET).
CET consists of two related security features: shadow stacks and
indirect branch tracking. This series implements just the shadow stack
part of this feature, and just for userspace.
The main use case for shadow stack is providing protection against
return oriented programming attacks. It works by maintaining a
secondary (shadow) stack using a special memory type that has
protections against modification. When executing a CALL instruction,
the processor pushes the return address to both the normal stack and
to the special permission shadow stack. Upon RET, the processor pops
the shadow stack copy and compares it to the normal stack copy.
For more information, refer to the links below for the earlier
versions of this patch set"
Link: https://lore.kernel.org/lkml/20220130211838.8382-1-rick.p.edgecombe@intel.com/
Link: https://lore.kernel.org/lkml/20230613001108.3040476-1-rick.p.edgecombe@intel.com/
* tag 'x86_shstk_for_6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
x86/shstk: Change order of __user in type
x86/ibt: Convert IBT selftest to asm
x86/shstk: Don't retry vm_munmap() on -EINTR
x86/kbuild: Fix Documentation/ reference
x86/shstk: Move arch detail comment out of core mm
x86/shstk: Add ARCH_SHSTK_STATUS
x86/shstk: Add ARCH_SHSTK_UNLOCK
x86: Add PTRACE interface for shadow stack
selftests/x86: Add shadow stack test
x86/cpufeatures: Enable CET CR4 bit for shadow stack
x86/shstk: Wire in shadow stack interface
x86: Expose thread features in /proc/$PID/status
x86/shstk: Support WRSS for userspace
x86/shstk: Introduce map_shadow_stack syscall
x86/shstk: Check that signal frame is shadow stack mem
x86/shstk: Check that SSP is aligned on sigreturn
x86/shstk: Handle signals for shadow stack
x86/shstk: Introduce routines modifying shstk
x86/shstk: Handle thread shadow stack
x86/shstk: Add user-mode shadow stack support
...
- Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier events to pass
action specific data without needing to constantly update the main handlers.
- Drop unused function declarations
-----BEGIN PGP SIGNATURE-----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=n819
-----END PGP SIGNATURE-----
Merge tag 'kvm-x86-generic-6.6' of https://github.com/kvm-x86/linux into HEAD
Common KVM changes for 6.6:
- Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier events to pass
action specific data without needing to constantly update the main handlers.
- Drop unused function declarations
- Add support for TLB range invalidation of Stage-2 page tables,
avoiding unnecessary invalidations. Systems that do not implement
range invalidation still rely on a full invalidation when dealing
with large ranges.
- Add infrastructure for forwarding traps taken from a L2 guest to
the L1 guest, with L0 acting as the dispatcher, another baby step
towards the full nested support.
- Simplify the way we deal with the (long deprecated) 'CPU target',
resulting in a much needed cleanup.
- Fix another set of PMU bugs, both on the guest and host sides,
as we seem to never have any shortage of those...
- Relax the alignment requirements of EL2 VA allocations for
non-stack allocations, as we were otherwise wasting a lot of that
precious VA space.
- The usual set of non-functional cleanups, although I note the lack
of spelling fixes...
-----BEGIN PGP SIGNATURE-----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=DKhx
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for Linux 6.6
- Add support for TLB range invalidation of Stage-2 page tables,
avoiding unnecessary invalidations. Systems that do not implement
range invalidation still rely on a full invalidation when dealing
with large ranges.
- Add infrastructure for forwarding traps taken from a L2 guest to
the L1 guest, with L0 acting as the dispatcher, another baby step
towards the full nested support.
- Simplify the way we deal with the (long deprecated) 'CPU target',
resulting in a much needed cleanup.
- Fix another set of PMU bugs, both on the guest and host sides,
as we seem to never have any shortage of those...
- Relax the alignment requirements of EL2 VA allocations for
non-stack allocations, as we were otherwise wasting a lot of that
precious VA space.
- The usual set of non-functional cleanups, although I note the lack
of spelling fixes...
Charlie Jenkins <charlie@rivosinc.com> says:
Make sv48 the default address space for mmap as some applications
currently depend on this assumption. Users can now select a
desired address space using a non-zero hint address to mmap. Previously,
requesting the default address space from mmap by passing zero as the hint
address would result in using the largest address space possible. Some
applications depend on empty bits in the virtual address space, like Go and
Java, so this patch provides more flexibility for application developers.
* b4-shazam-merge:
RISC-V: mm: Document mmap changes
RISC-V: mm: Update pgtable comment documentation
RISC-V: mm: Add tests for RISC-V mm
RISC-V: mm: Restrict address space for sv39,sv48,sv57
Link: https://lore.kernel.org/r/20230809232218.849726-1-charlie@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Jisheng Zhang <jszhang@kernel.org> says:
Currently, riscv defines ARCH_DMA_MINALIGN as L1_CACHE_BYTES, I.E
64Bytes, if CONFIG_RISCV_DMA_NONCOHERENT=y. To support unified kernel
Image, usually we have to enable CONFIG_RISCV_DMA_NONCOHERENT, thus
it brings some bad effects to coherent platforms:
Firstly, it wastes memory, kmalloc-96, kmalloc-32, kmalloc-16 and
kmalloc-8 slab caches don't exist any more, they are replaced with
either kmalloc-128 or kmalloc-64.
Secondly, larger than necessary kmalloc aligned allocations results
in unnecessary cache/TLB pressure.
This issue also exists on arm64 platforms. From last year, Catalin
tried to solve this issue by decoupling ARCH_KMALLOC_MINALIGN from
ARCH_DMA_MINALIGN, limiting kmalloc() minimum alignment to
dma_get_cache_alignment() and replacing ARCH_KMALLOC_MINALIGN usage
in various drivers with ARCH_DMA_MINALIGN etc.[1]
One fact we can make use of for riscv: if the CPU doesn't support
ZICBOM or T-HEAD CMO, we know the platform is coherent. Based on
Catalin's work and above fact, we can easily solve the kmalloc align
issue for riscv: we can override dma_get_cache_alignment(), then let
it return ARCH_DMA_MINALIGN at the beginning and return 1 once we know
the underlying HW neither supports ZICBOM nor supports T-HEAD CMO.
So what about if the CPU supports ZICBOM or T-HEAD CMO, but all the
devices are dma coherent? Well, we use ARCH_DMA_MINALIGN as the
kmalloc minimum alignment, nothing changed in this case. This case
can be improved in the future once we see such platforms in mainline.
After this patch, a simple test of booting to a small buildroot rootfs
on qemu shows:
kmalloc-96 5041 5041 96 ...
kmalloc-64 9606 9606 64 ...
kmalloc-32 5128 5128 32 ...
kmalloc-16 7682 7682 16 ...
kmalloc-8 10246 10246 8 ...
So we save about 1268KB memory. The saving will be much larger in normal
OS env on real HW platforms.
patch1 allows kmalloc() caches aligned to the smallest value.
patch2 enables DMA_BOUNCE_UNALIGNED_KMALLOC.
After this series:
As for coherent platforms, kmalloc-{8,16,32,96} caches come back on
coherent both RV32 and RV64 platforms, I.E !ZICBOM and !THEAD_CMO.
As for noncoherent RV32 platforms, nothing changed.
As for noncoherent RV64 platforms, I.E either ZICBOM or THEAD_CMO, the
above kmalloc caches also come back if > 4GB memory or users pass
"swiotlb=mmnn,force" to force swiotlb creation if <= 4GB memory. How
much mmnn should be depends on the specific platform, it needs to be
tried and tested all possible usage case on the specific hardware. For
example, I can use the minimal I/O TLB slabs on Sipeed M1S Dock.
* b4-shazam-merge:
riscv: enable DMA_BOUNCE_UNALIGNED_KMALLOC for !dma_coherent
riscv: allow kmalloc() caches aligned to the smallest value
Link: https://lore.kernel.org/linux-arm-kernel/20230524171904.3967031-1-catalin.marinas@arm.com/ [1]
Link: https://lore.kernel.org/r/20230718152214.2907-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Currently, each architecture can support PREEMPT_DYNAMIC through
either static calls or static keys. To support PREEMPT_DYNAMIC on
riscv, we face three choices:
1. only add static calls support to riscv
As Mark pointed out in commit 99cf983cc8 ("sched/preempt: Add
PREEMPT_DYNAMIC using static keys"), static keys "...should have
slightly lower overhead than non-inline static calls, as this
effectively inlines each trampoline into the start of its callee. This
may avoid redundant work, and may integrate better with CFI schemes."
So even we add static calls(without inline static calls) to riscv,
static keys is still a better choice.
2. add static calls and inline static calls to riscv
Per my understanding, inline static calls requires objtool support
which is not easy.
3. use static keys
While riscv doesn't have static calls support, it supports static keys
perfectly. So this patch selects HAVE_PREEMPT_DYNAMIC_KEY to enable
support for PREEMPT_DYNAMIC on riscv, so that the preemption model can
be chosen at boot time. It also patches asm-generic/preempt.h, mainly
to add __preempt_schedule() and __preempt_schedule_notrace() macros
for PREEMPT_DYNAMIC case. Other architectures which use generic
preempt.h can also benefit from this patch by simply selecting
HAVE_PREEMPT_DYNAMIC_KEY to enable PREEMPT_DYNAMIC if they supports
static keys.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230716164925.1858-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Greg Ungerer <gerg@kernel.org> says:
The following changes add the ability to run ELF format binaries when
running RISC-V in nommu mode. That support is actually part of the
ELF-FDPIC loader, so these changes are all about making that work on
RISC-V.
The first issue to deal with is making the ELF-FDPIC loader capable of
handling 64-bit ELF files. As coded right now it only supports 32-bit
ELF files.
Secondly some changes are required to enable and compile the ELF-FDPIC
loader on RISC-V and to pass the ELF-FDPIC mapping addresses through to
user space when execing the new program.
These changes have not been used to run actual ELF-FDPIC binaries.
It is used to load and run normal ELF - compiled -pie format. Though the
underlying changes are expected to work with full ELF-FDPIC binaries if
or when that is supported on RISC-V in gcc.
To avoid needing changes to the C-library (tested with uClibc-ng
currently) there is a simple runtime dynamic loader (interpreter)
available to do the final relocations, https://github.com/gregungerer/uldso.
The nice thing about doing it this way is that the same program
binary can also be loaded with the usual ELF loader in MMU linux.
The motivation here is to provide an easy to use alternative to the
flat format binaries normally used for RISC-V nommu based systems.
* b4-shazam-merge:
riscv: support the elf-fdpic binfmt loader
binfmt_elf_fdpic: support 64-bit systems
Link: https://lore.kernel.org/r/20230711130754.481209-1-gerg@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Sami Tolvanen <samitolvanen@google.com> says:
This series adds KCFI support for RISC-V. KCFI is a fine-grained
forward-edge control-flow integrity scheme supported in Clang >=16,
which ensures indirect calls in instrumented code can only branch to
functions whose type matches the function pointer type, thus making
code reuse attacks more difficult.
Patch 1 implements a pt_regs based syscall wrapper to address
function pointer type mismatches in syscall handling. Patches 2 and 3
annotate indirectly called assembly functions with CFI types. Patch 4
implements error handling for indirect call checks. Patch 5 disables
CFI for arch/riscv/purgatory. Patch 6 finally allows CONFIG_CFI_CLANG
to be enabled for RISC-V.
Note that Clang 16 has a generic architecture-agnostic KCFI
implementation, which does work with the kernel, but doesn't produce
a stable code sequence for indirect call checks, which means
potential failures just trap and won't result in informative error
messages. Clang 17 includes a RISC-V specific back-end implementation
for KCFI, which emits a predictable code sequence for the checks and a
.kcfi_traps section with locations of the traps, which patch 5 uses to
produce more useful errors.
The type mismatch fixes and annotations in the first three patches
also become necessary in future if the kernel decides to support
fine-grained CFI implemented using the hardware landing pad
feature proposed in the in-progress Zicfisslp extension. Once the
specification is ratified and hardware support emerges, implementing
runtime patching support that replaces KCFI instrumentation with
Zicfisslp landing pads might also be feasible (similarly to KCFI to
FineIBT patching on x86_64), allowing distributions to ship a unified
kernel binary for all devices.
* b4-shazam-merge:
riscv: Allow CONFIG_CFI_CLANG to be selected
riscv/purgatory: Disable CFI
riscv: Add CFI error handling
riscv: Add ftrace_stub_graph
riscv: Add types to indirectly called assembly functions
riscv: Implement syscall wrappers
Link: https://lore.kernel.org/r/20230710183544.999540-8-samitolvanen@google.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
bitmap_zero() is faster than bitmap_clear(), so use bitmap_zero()
instead of bitmap_clear().
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/202305061711417142802@zte.com.cn
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Chen Jiahao <chenjiahao16@huawei.com> says:
On riscv, the current crash kernel allocation logic is trying to
allocate within 32bit addressible memory region by default, if
failed, try to allocate without 4G restriction.
In need of saving DMA zone memory while allocating a relatively large
crash kernel region, allocating the reserved memory top down in
high memory, without overlapping the DMA zone, is a mature solution.
Hence this patchset introduces the parameter option crashkernel=X,[high,low].
One can reserve the crash kernel from high memory above DMA zone range
by explicitly passing "crashkernel=X,high"; or reserve a memory range
below 4G with "crashkernel=X,low". Besides, there are few rules need
to take notice:
1. "crashkernel=X,[high,low]" will be ignored if "crashkernel=size"
is specified.
2. "crashkernel=X,low" is valid only when "crashkernel=X,high" is passed
and there is enough memory to be allocated under 4G.
3. When allocating crashkernel above 4G and no "crashkernel=X,low" is
specified, a 128M low memory will be allocated automatically for
swiotlb bounce buffer.
See Documentation/admin-guide/kernel-parameters.txt for more information.
To verify loading the crashkernel, adapted kexec-tools is attached below:
https://github.com/chenjh005/kexec-tools/tree/build-test-riscv-v2
Following test cases have been performed as expected:
1) crashkernel=256M //low=256M
2) crashkernel=1G //low=1G
3) crashkernel=4G //high=4G, low=128M(default)
4) crashkernel=4G crashkernel=256M,high //high=4G, low=128M(default), high is ignored
5) crashkernel=4G crashkernel=256M,low //high=4G, low=128M(default), low is ignored
6) crashkernel=4G,high //high=4G, low=128M(default)
7) crashkernel=256M,low //low=0M, invalid
8) crashkernel=4G,high crashkernel=256M,low //high=4G, low=256M
9) crashkernel=4G,high crashkernel=4G,low //high=0M, low=0M, invalid
10) crashkernel=512M@0xd0000000 //low=512M
11) crashkernel=1G,high crashkernel=0M,low //high=1G, low=0M
* b4-shazam-merge:
docs: kdump: Update the crashkernel description for riscv
riscv: kdump: Implement crashkernel=X,[high,low]
Link: https://lore.kernel.org/r/20230726175000.2536220-1-chenjiahao16@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Nam Cao <namcaov@gmail.com> says:
Simulate some currently rejected instructions. Still to be simulated are:
- c.jal
- c.ebreak
* b4-shazam-merge:
riscv: kprobes: simulate c.beqz and c.bnez
riscv: kprobes: simulate c.jr and c.jalr instructions
riscv: kprobes: simulate c.j instruction
Link: https://lore.kernel.org/r/cover.1690704360.git.namcaov@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Some mv instructions were useful when first introduced to preserve a0 and
a1 before function calls. However the code has changed and they are now
redundant. Remove them.
Signed-off-by: Nam Cao <namcaov@gmail.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230725053835.138910-1-namcaov@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
These are the remaining few clean-ups of DT related includes which
didn't get applied to subsystem trees.
-----BEGIN PGP SIGNATURE-----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=eLMf
-----END PGP SIGNATURE-----
Merge tag 'devicetree-header-cleanups-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree include cleanups from Rob Herring:
"These are the remaining few clean-ups of DT related includes which
didn't get applied to subsystem trees"
* tag 'devicetree-header-cleanups-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ipmi: Explicitly include correct DT includes
tpm: Explicitly include correct DT includes
lib/genalloc: Explicitly include correct DT includes
parport: Explicitly include correct DT includes
sbus: Explicitly include correct DT includes
mux: Explicitly include correct DT includes
macintosh: Explicitly include correct DT includes
hte: Explicitly include correct DT includes
EDAC: Explicitly include correct DT includes
clocksource: Explicitly include correct DT includes
sparc: Explicitly include correct DT includes
riscv: Explicitly include correct DT includes
These are the devicetree updates for Arm and RISC-V based SoCs,
mainly from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips,
Samsung, ST and Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an
Cortex-A76/A55 SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile
phone platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches in
total, most of which are cleanups and minor fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmTuZOQACgkQYKtH/8kJ
UieJGw/5AWNde1VYY/3uhdHSNeXtF+1LICZYoLQiSTWbpnlEoLhQseymRCybWRhd
882TLCuEMrHV+ftP5z+kdYS+QJE3K8GNRxp4vAgLTRwnZItEE3qD8/jNeTtK5BqT
7h9OYZJQhfczsIXISIljsvez2T3n5fA1glq2drc2fLl9AbEYvlByDCtCNmzqMYli
II/S03vJqT3eFnOwut70EdFtnW3FIJ+HJLWu46zWLhrx2XJVS8hNaWqhQ3uKZ58p
Q9cWAltu4biaILVpD/0vZST+m77HqcrPtVSwR9uHvzEzDEzYk/GYzn7DDlWgdVbt
DJMkgK1pLJq67KpsefMqgTioCh2FBiWfNQ6FjsgJ06ykXgThLJfbzeeB4zU4fnDT
YmcV/8gR6Np/wNeSBlPNLI6BZ1EF4h0Lkm6p//QgayYhdMVbE59K+SNwq4wps24l
JU3dcxxblwpVmAaKSL5p0lbYTn8VKuz9rcXYIziQm1m8zaCwjq863bDFJKz8JsP8
0tQ/azvS4Off9fKIMbUE4fiFmDGhgLTi0XL+GIlOFJF6JS6ToD2nL4FGRBJZPWNn
iPNEV0F/dDnonB7Jfu92NodULY6B0mXs5/q+dPwde6oSpIDU2ORyNRb6Zk4fGC0l
C+iPdb3BErf+GQYBLnRqQaMuV0sA6mN89lC6KlzWwwHK0UUoohg=
=bO3j
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
("refactor Kconfig to consolidate KEXEC and CRASH options").
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h").
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands").
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions").
- Switch the handling of kdump from a udev scheme to in-kernel handling,
by Eric DeVolder ("crash: Kernel handling of CPU and memory hot
un/plug").
- Many singleton patches to various parts of the tree
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZO2GpAAKCRDdBJ7gKXxA
juW3AQD1moHzlSN6x9I3tjm5TWWNYFoFL8af7wXDJspp/DWH/AD/TO0XlWWhhbYy
QHy7lL0Syha38kKLMXTM+bN6YQHi9AU=
=WJQa
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- An extensive rework of kexec and crash Kconfig from Eric DeVolder
("refactor Kconfig to consolidate KEXEC and CRASH options")
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h")
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands")
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions")
- Switch the handling of kdump from a udev scheme to in-kernel
handling, by Eric DeVolder ("crash: Kernel handling of CPU and memory
hot un/plug")
- Many singleton patches to various parts of the tree
* tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (81 commits)
document while_each_thread(), change first_tid() to use for_each_thread()
drivers/char/mem.c: shrink character device's devlist[] array
x86/crash: optimize CPU changes
crash: change crash_prepare_elf64_headers() to for_each_possible_cpu()
crash: hotplug support for kexec_load()
x86/crash: add x86 crash hotplug support
crash: memory and CPU hotplug sysfs attributes
kexec: exclude elfcorehdr from the segment digest
crash: add generic infrastructure for crash hotplug support
crash: move a few code bits to setup support of crash hotplug
kstrtox: consistently use _tolower()
kill do_each_thread()
nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
scripts/bloat-o-meter: count weak symbol sizes
treewide: drop CONFIG_EMBEDDED
lockdep: fix static memory detection even more
lib/vsprintf: declare no_hash_pointers in sprintf.h
lib/vsprintf: split out sprintf() and friends
kernel/fork: stop playing lockless games for exe_file replacement
adfs: delete unused "union adfs_dirtail" definition
...
- Peter Xu has a series (mm/gup: Unify hugetlb, speed up thp") which
reduces the special-case code for handling hugetlb pages in GUP. It
also speeds up GUP handling of transparent hugepages.
- Peng Zhang provides some maple tree speedups ("Optimize the fast path
of mas_store()").
- Sergey Senozhatsky has improved te performance of zsmalloc during
compaction (zsmalloc: small compaction improvements").
- Domenico Cerasuolo has developed additional selftest code for zswap
("selftests: cgroup: add zswap test program").
- xu xin has doe some work on KSM's handling of zero pages. These
changes are mainly to enable the user to better understand the
effectiveness of KSM's treatment of zero pages ("ksm: support tracking
KSM-placed zero-pages").
- Jeff Xu has fixes the behaviour of memfd's
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED sysctl ("mm/memfd: fix sysctl
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED").
- David Howells has fixed an fscache optimization ("mm, netfs, fscache:
Stop read optimisation when folio removed from pagecache").
- Axel Rasmussen has given userfaultfd the ability to simulate memory
poisoning ("add UFFDIO_POISON to simulate memory poisoning with UFFD").
- Miaohe Lin has contributed some routine maintenance work on the
memory-failure code ("mm: memory-failure: remove unneeded PageHuge()
check").
- Peng Zhang has contributed some maintenance work on the maple tree
code ("Improve the validation for maple tree and some cleanup").
- Hugh Dickins has optimized the collapsing of shmem or file pages into
THPs ("mm: free retracted page table by RCU").
- Jiaqi Yan has a patch series which permits us to use the healthy
subpages within a hardware poisoned huge page for general purposes
("Improve hugetlbfs read on HWPOISON hugepages").
- Kemeng Shi has done some maintenance work on the pagetable-check code
("Remove unused parameters in page_table_check").
- More folioification work from Matthew Wilcox ("More filesystem folio
conversions for 6.6"), ("Followup folio conversions for zswap"). And
from ZhangPeng ("Convert several functions in page_io.c to use a
folio").
- page_ext cleanups from Kemeng Shi ("minor cleanups for page_ext").
- Baoquan He has converted some architectures to use the GENERIC_IOREMAP
ioremap()/iounmap() code ("mm: ioremap: Convert architectures to take
GENERIC_IOREMAP way").
- Anshuman Khandual has optimized arm64 tlb shootdown ("arm64: support
batched/deferred tlb shootdown during page reclamation/migration").
- Better maple tree lockdep checking from Liam Howlett ("More strict
maple tree lockdep"). Liam also developed some efficiency improvements
("Reduce preallocations for maple tree").
- Cleanup and optimization to the secondary IOMMU TLB invalidation, from
Alistair Popple ("Invalidate secondary IOMMU TLB on permission
upgrade").
- Ryan Roberts fixes some arm64 MM selftest issues ("selftests/mm fixes
for arm64").
- Kemeng Shi provides some maintenance work on the compaction code ("Two
minor cleanups for compaction").
- Some reduction in mmap_lock pressure from Matthew Wilcox ("Handle most
file-backed faults under the VMA lock").
- Aneesh Kumar contributes code to use the vmemmap optimization for DAX
on ppc64, under some circumstances ("Add support for DAX vmemmap
optimization for ppc64").
- page-ext cleanups from Kemeng Shi ("add page_ext_data to get client
data in page_ext"), ("minor cleanups to page_ext header").
- Some zswap cleanups from Johannes Weiner ("mm: zswap: three
cleanups").
- kmsan cleanups from ZhangPeng ("minor cleanups for kmsan").
- VMA handling cleanups from Kefeng Wang ("mm: convert to
vma_is_initial_heap/stack()").
- DAMON feature work from SeongJae Park ("mm/damon/sysfs-schemes:
implement DAMOS tried total bytes file"), ("Extend DAMOS filters for
address ranges and DAMON monitoring targets").
- Compaction work from Kemeng Shi ("Fixes and cleanups to compaction").
- Liam Howlett has improved the maple tree node replacement code
("maple_tree: Change replacement strategy").
- ZhangPeng has a general code cleanup - use the K() macro more widely
("cleanup with helper macro K()").
- Aneesh Kumar brings memmap-on-memory to ppc64 ("Add support for memmap
on memory feature on ppc64").
- pagealloc cleanups from Kemeng Shi ("Two minor cleanups for pcp list
in page_alloc"), ("Two minor cleanups for get pageblock migratetype").
- Vishal Moola introduces a memory descriptor for page table tracking,
"struct ptdesc" ("Split ptdesc from struct page").
- memfd selftest maintenance work from Aleksa Sarai ("memfd: cleanups
for vm.memfd_noexec").
- MM include file rationalization from Hugh Dickins ("arch: include
asm/cacheflush.h in asm/hugetlb.h").
- THP debug output fixes from Hugh Dickins ("mm,thp: fix sloppy text
output").
- kmemleak improvements from Xiaolei Wang ("mm/kmemleak: use
object_cache instead of kmemleak_initialized").
- More folio-related cleanups from Matthew Wilcox ("Remove _folio_dtor
and _folio_order").
- A VMA locking scalability improvement from Suren Baghdasaryan
("Per-VMA lock support for swap and userfaults").
- pagetable handling cleanups from Matthew Wilcox ("New page table range
API").
- A batch of swap/thp cleanups from David Hildenbrand ("mm/swap: stop
using page->private on tail pages for THP_SWAP + cleanups").
- Cleanups and speedups to the hugetlb fault handling from Matthew
Wilcox ("Change calling convention for ->huge_fault").
- Matthew Wilcox has also done some maintenance work on the MM subsystem
documentation ("Improve mm documentation").
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZO1JUQAKCRDdBJ7gKXxA
jrMwAP47r/fS8vAVT3zp/7fXmxaJYTK27CTAM881Gw1SDhFM/wEAv8o84mDenCg6
Nfio7afS1ncD+hPYT8947UnLxTgn+ww=
=Afws
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-08-28-18-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Some swap cleanups from Ma Wupeng ("fix WARN_ON in
add_to_avail_list")
- Peter Xu has a series (mm/gup: Unify hugetlb, speed up thp") which
reduces the special-case code for handling hugetlb pages in GUP. It
also speeds up GUP handling of transparent hugepages.
- Peng Zhang provides some maple tree speedups ("Optimize the fast path
of mas_store()").
- Sergey Senozhatsky has improved te performance of zsmalloc during
compaction (zsmalloc: small compaction improvements").
- Domenico Cerasuolo has developed additional selftest code for zswap
("selftests: cgroup: add zswap test program").
- xu xin has doe some work on KSM's handling of zero pages. These
changes are mainly to enable the user to better understand the
effectiveness of KSM's treatment of zero pages ("ksm: support
tracking KSM-placed zero-pages").
- Jeff Xu has fixes the behaviour of memfd's
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED sysctl ("mm/memfd: fix sysctl
MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED").
- David Howells has fixed an fscache optimization ("mm, netfs, fscache:
Stop read optimisation when folio removed from pagecache").
- Axel Rasmussen has given userfaultfd the ability to simulate memory
poisoning ("add UFFDIO_POISON to simulate memory poisoning with
UFFD").
- Miaohe Lin has contributed some routine maintenance work on the
memory-failure code ("mm: memory-failure: remove unneeded PageHuge()
check").
- Peng Zhang has contributed some maintenance work on the maple tree
code ("Improve the validation for maple tree and some cleanup").
- Hugh Dickins has optimized the collapsing of shmem or file pages into
THPs ("mm: free retracted page table by RCU").
- Jiaqi Yan has a patch series which permits us to use the healthy
subpages within a hardware poisoned huge page for general purposes
("Improve hugetlbfs read on HWPOISON hugepages").
- Kemeng Shi has done some maintenance work on the pagetable-check code
("Remove unused parameters in page_table_check").
- More folioification work from Matthew Wilcox ("More filesystem folio
conversions for 6.6"), ("Followup folio conversions for zswap"). And
from ZhangPeng ("Convert several functions in page_io.c to use a
folio").
- page_ext cleanups from Kemeng Shi ("minor cleanups for page_ext").
- Baoquan He has converted some architectures to use the
GENERIC_IOREMAP ioremap()/iounmap() code ("mm: ioremap: Convert
architectures to take GENERIC_IOREMAP way").
- Anshuman Khandual has optimized arm64 tlb shootdown ("arm64: support
batched/deferred tlb shootdown during page reclamation/migration").
- Better maple tree lockdep checking from Liam Howlett ("More strict
maple tree lockdep"). Liam also developed some efficiency
improvements ("Reduce preallocations for maple tree").
- Cleanup and optimization to the secondary IOMMU TLB invalidation,
from Alistair Popple ("Invalidate secondary IOMMU TLB on permission
upgrade").
- Ryan Roberts fixes some arm64 MM selftest issues ("selftests/mm fixes
for arm64").
- Kemeng Shi provides some maintenance work on the compaction code
("Two minor cleanups for compaction").
- Some reduction in mmap_lock pressure from Matthew Wilcox ("Handle
most file-backed faults under the VMA lock").
- Aneesh Kumar contributes code to use the vmemmap optimization for DAX
on ppc64, under some circumstances ("Add support for DAX vmemmap
optimization for ppc64").
- page-ext cleanups from Kemeng Shi ("add page_ext_data to get client
data in page_ext"), ("minor cleanups to page_ext header").
- Some zswap cleanups from Johannes Weiner ("mm: zswap: three
cleanups").
- kmsan cleanups from ZhangPeng ("minor cleanups for kmsan").
- VMA handling cleanups from Kefeng Wang ("mm: convert to
vma_is_initial_heap/stack()").
- DAMON feature work from SeongJae Park ("mm/damon/sysfs-schemes:
implement DAMOS tried total bytes file"), ("Extend DAMOS filters for
address ranges and DAMON monitoring targets").
- Compaction work from Kemeng Shi ("Fixes and cleanups to compaction").
- Liam Howlett has improved the maple tree node replacement code
("maple_tree: Change replacement strategy").
- ZhangPeng has a general code cleanup - use the K() macro more widely
("cleanup with helper macro K()").
- Aneesh Kumar brings memmap-on-memory to ppc64 ("Add support for
memmap on memory feature on ppc64").
- pagealloc cleanups from Kemeng Shi ("Two minor cleanups for pcp list
in page_alloc"), ("Two minor cleanups for get pageblock
migratetype").
- Vishal Moola introduces a memory descriptor for page table tracking,
"struct ptdesc" ("Split ptdesc from struct page").
- memfd selftest maintenance work from Aleksa Sarai ("memfd: cleanups
for vm.memfd_noexec").
- MM include file rationalization from Hugh Dickins ("arch: include
asm/cacheflush.h in asm/hugetlb.h").
- THP debug output fixes from Hugh Dickins ("mm,thp: fix sloppy text
output").
- kmemleak improvements from Xiaolei Wang ("mm/kmemleak: use
object_cache instead of kmemleak_initialized").
- More folio-related cleanups from Matthew Wilcox ("Remove _folio_dtor
and _folio_order").
- A VMA locking scalability improvement from Suren Baghdasaryan
("Per-VMA lock support for swap and userfaults").
- pagetable handling cleanups from Matthew Wilcox ("New page table
range API").
- A batch of swap/thp cleanups from David Hildenbrand ("mm/swap: stop
using page->private on tail pages for THP_SWAP + cleanups").
- Cleanups and speedups to the hugetlb fault handling from Matthew
Wilcox ("Change calling convention for ->huge_fault").
- Matthew Wilcox has also done some maintenance work on the MM
subsystem documentation ("Improve mm documentation").
* tag 'mm-stable-2023-08-28-18-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (489 commits)
maple_tree: shrink struct maple_tree
maple_tree: clean up mas_wr_append()
secretmem: convert page_is_secretmem() to folio_is_secretmem()
nios2: fix flush_dcache_page() for usage from irq context
hugetlb: add documentation for vma_kernel_pagesize()
mm: add orphaned kernel-doc to the rst files.
mm: fix clean_record_shared_mapping_range kernel-doc
mm: fix get_mctgt_type() kernel-doc
mm: fix kernel-doc warning from tlb_flush_rmaps()
mm: remove enum page_entry_size
mm: allow ->huge_fault() to be called without the mmap_lock held
mm: move PMD_ORDER to pgtable.h
mm: remove checks for pte_index
memcg: remove duplication detection for mem_cgroup_uncharge_swap
mm/huge_memory: work on folio->swap instead of page->private when splitting folio
mm/swap: inline folio_set_swap_entry() and folio_swap_entry()
mm/swap: use dedicated entry for swap in folio
mm/swap: stop using page->private on tail pages for THP_SWAP
selftests/mm: fix WARNING comparing pointer to 0
selftests: cgroup: fix test_kmem_memcg_deletion kernel mem check
...
Core
----
- Increase size limits for to-be-sent skb frag allocations. This
allows tun, tap devices and packet sockets to better cope with large
writes operations.
- Store netdevs in an xarray, to simplify iterating over netdevs.
- Refactor nexthop selection for multipath routes.
- Improve sched class lifetime handling.
- Add backup nexthop ID support for bridge.
- Implement drop reasons support in openvswitch.
- Several data races annotations and fixes.
- Constify the sk parameter of routing functions.
- Prepend kernel version to netconsole message.
Protocols
---------
- Implement support for TCP probing the peer being under memory
pressure.
- Remove hard coded limitation on IPv6 specific info placement
inside the socket struct.
- Get rid of sysctl_tcp_adv_win_scale and use an auto-estimated
per socket scaling factor.
- Scaling-up the IPv6 expired route GC via a separated list of
expiring routes.
- In-kernel support for the TLS alert protocol.
- Better support for UDP reuseport with connected sockets.
- Add NEXT-C-SID support for SRv6 End.X behavior, reducing the SR
header size.
- Get rid of additional ancillary per MPTCP connection struct socket.
- Implement support for BPF-based MPTCP packet schedulers.
- Format MPTCP subtests selftests results in TAP.
- Several new SMC 2.1 features including unique experimental options,
max connections per lgr negotiation, max links per lgr negotiation.
BPF
---
- Multi-buffer support in AF_XDP.
- Add multi uprobe BPF links for attaching multiple uprobes
and usdt probes, which is significantly faster and saves extra fds.
- Implement an fd-based tc BPF attach API (TCX) and BPF link support on
top of it.
- Add SO_REUSEPORT support for TC bpf_sk_assign.
- Support new instructions from cpu v4 to simplify the generated code and
feature completeness, for x86, arm64, riscv64.
- Support defragmenting IPv(4|6) packets in BPF.
- Teach verifier actual bounds of bpf_get_smp_processor_id()
and fix perf+libbpf issue related to custom section handling.
- Introduce bpf map element count and enable it for all program types.
- Add a BPF hook in sys_socket() to change the protocol ID
from IPPROTO_TCP to IPPROTO_MPTCP to cover migration for legacy.
- Introduce bpf_me_mcache_free_rcu() and fix OOM under stress.
- Add uprobe support for the bpf_get_func_ip helper.
- Check skb ownership against full socket.
- Support for up to 12 arguments in BPF trampoline.
- Extend link_info for kprobe_multi and perf_event links.
Netfilter
---------
- Speed-up process exit by aborting ruleset validation if a
fatal signal is pending.
- Allow NLA_POLICY_MASK to be used with BE16/BE32 types.
Driver API
----------
- Page pool optimizations, to improve data locality and cache usage.
- Introduce ndo_hwtstamp_get() and ndo_hwtstamp_set() to avoid the need
for raw ioctl() handling in drivers.
- Simplify genetlink dump operations (doit/dumpit) providing them
the common information already populated in struct genl_info.
- Extend and use the yaml devlink specs to [re]generate the split ops.
- Introduce devlink selective dumps, to allow SF filtering SF based on
handle and other attributes.
- Add yaml netlink spec for netlink-raw families, allow route, link and
address related queries via the ynl tool.
- Remove phylink legacy mode support.
- Support offload LED blinking to phy.
- Add devlink port function attributes for IPsec.
New hardware / drivers
----------------------
- Ethernet:
- Broadcom ASP 2.0 (72165) ethernet controller
- MediaTek MT7988 SoC
- Texas Instruments AM654 SoC
- Texas Instruments IEP driver
- Atheros qca8081 phy
- Marvell 88Q2110 phy
- NXP TJA1120 phy
- WiFi:
- MediaTek mt7981 support
- Can:
- Kvaser SmartFusion2 PCI Express devices
- Allwinner T113 controllers
- Texas Instruments tcan4552/4553 chips
- Bluetooth:
- Intel Gale Peak
- Qualcomm WCN3988 and WCN7850
- NXP AW693 and IW624
- Mediatek MT2925
Drivers
-------
- Ethernet NICs:
- nVidia/Mellanox:
- mlx5:
- support UDP encapsulation in packet offload mode
- IPsec packet offload support in eswitch mode
- improve aRFS observability by adding new set of counters
- extends MACsec offload support to cover RoCE traffic
- dynamic completion EQs
- mlx4:
- convert to use auxiliary bus instead of custom interface logic
- Intel
- ice:
- implement switchdev bridge offload, even for LAG interfaces
- implement SRIOV support for LAG interfaces
- igc:
- add support for multiple in-flight TX timestamps
- Broadcom:
- bnxt:
- use the unified RX page pool buffers for XDP and non-XDP
- use the NAPI skb allocation cache
- OcteonTX2:
- support Round Robin scheduling HTB offload
- TC flower offload support for SPI field
- Freescale:
- add XDP_TX feature support
- AMD:
- ionic: add support for PCI FLR event
- sfc:
- basic conntrack offload
- introduce eth, ipv4 and ipv6 pedit offloads
- ST Microelectronics:
- stmmac: maximze PTP timestamping resolution
- Virtual NICs:
- Microsoft vNIC:
- batch ringing RX queue doorbell on receiving packets
- add page pool for RX buffers
- Virtio vNIC:
- add per queue interrupt coalescing support
- Google vNIC:
- add queue-page-list mode support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add port range matching tc-flower offload
- permit enslavement to netdevices with uppers
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- convert to phylink_pcs
- Renesas:
- r8A779fx: add speed change support
- rzn1: enables vlan support
- Ethernet PHYs:
- convert mv88e6xxx to phylink_pcs
- WiFi:
- Qualcomm Wi-Fi 7 (ath12k):
- extremely High Throughput (EHT) PHY support
- RealTek (rtl8xxxu):
- enable AP mode for: RTL8192FU, RTL8710BU (RTL8188GU),
RTL8192EU and RTL8723BU
- RealTek (rtw89):
- Introduce Time Averaged SAR (TAS) support
- Connector:
- support for event filtering
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=9CsR
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Increase size limits for to-be-sent skb frag allocations. This
allows tun, tap devices and packet sockets to better cope with
large writes operations
- Store netdevs in an xarray, to simplify iterating over netdevs
- Refactor nexthop selection for multipath routes
- Improve sched class lifetime handling
- Add backup nexthop ID support for bridge
- Implement drop reasons support in openvswitch
- Several data races annotations and fixes
- Constify the sk parameter of routing functions
- Prepend kernel version to netconsole message
Protocols:
- Implement support for TCP probing the peer being under memory
pressure
- Remove hard coded limitation on IPv6 specific info placement inside
the socket struct
- Get rid of sysctl_tcp_adv_win_scale and use an auto-estimated per
socket scaling factor
- Scaling-up the IPv6 expired route GC via a separated list of
expiring routes
- In-kernel support for the TLS alert protocol
- Better support for UDP reuseport with connected sockets
- Add NEXT-C-SID support for SRv6 End.X behavior, reducing the SR
header size
- Get rid of additional ancillary per MPTCP connection struct socket
- Implement support for BPF-based MPTCP packet schedulers
- Format MPTCP subtests selftests results in TAP
- Several new SMC 2.1 features including unique experimental options,
max connections per lgr negotiation, max links per lgr negotiation
BPF:
- Multi-buffer support in AF_XDP
- Add multi uprobe BPF links for attaching multiple uprobes and usdt
probes, which is significantly faster and saves extra fds
- Implement an fd-based tc BPF attach API (TCX) and BPF link support
on top of it
- Add SO_REUSEPORT support for TC bpf_sk_assign
- Support new instructions from cpu v4 to simplify the generated code
and feature completeness, for x86, arm64, riscv64
- Support defragmenting IPv(4|6) packets in BPF
- Teach verifier actual bounds of bpf_get_smp_processor_id() and fix
perf+libbpf issue related to custom section handling
- Introduce bpf map element count and enable it for all program types
- Add a BPF hook in sys_socket() to change the protocol ID from
IPPROTO_TCP to IPPROTO_MPTCP to cover migration for legacy
- Introduce bpf_me_mcache_free_rcu() and fix OOM under stress
- Add uprobe support for the bpf_get_func_ip helper
- Check skb ownership against full socket
- Support for up to 12 arguments in BPF trampoline
- Extend link_info for kprobe_multi and perf_event links
Netfilter:
- Speed-up process exit by aborting ruleset validation if a fatal
signal is pending
- Allow NLA_POLICY_MASK to be used with BE16/BE32 types
Driver API:
- Page pool optimizations, to improve data locality and cache usage
- Introduce ndo_hwtstamp_get() and ndo_hwtstamp_set() to avoid the
need for raw ioctl() handling in drivers
- Simplify genetlink dump operations (doit/dumpit) providing them the
common information already populated in struct genl_info
- Extend and use the yaml devlink specs to [re]generate the split ops
- Introduce devlink selective dumps, to allow SF filtering SF based
on handle and other attributes
- Add yaml netlink spec for netlink-raw families, allow route, link
and address related queries via the ynl tool
- Remove phylink legacy mode support
- Support offload LED blinking to phy
- Add devlink port function attributes for IPsec
New hardware / drivers:
- Ethernet:
- Broadcom ASP 2.0 (72165) ethernet controller
- MediaTek MT7988 SoC
- Texas Instruments AM654 SoC
- Texas Instruments IEP driver
- Atheros qca8081 phy
- Marvell 88Q2110 phy
- NXP TJA1120 phy
- WiFi:
- MediaTek mt7981 support
- Can:
- Kvaser SmartFusion2 PCI Express devices
- Allwinner T113 controllers
- Texas Instruments tcan4552/4553 chips
- Bluetooth:
- Intel Gale Peak
- Qualcomm WCN3988 and WCN7850
- NXP AW693 and IW624
- Mediatek MT2925
Drivers:
- Ethernet NICs:
- nVidia/Mellanox:
- mlx5:
- support UDP encapsulation in packet offload mode
- IPsec packet offload support in eswitch mode
- improve aRFS observability by adding new set of counters
- extends MACsec offload support to cover RoCE traffic
- dynamic completion EQs
- mlx4:
- convert to use auxiliary bus instead of custom interface
logic
- Intel
- ice:
- implement switchdev bridge offload, even for LAG
interfaces
- implement SRIOV support for LAG interfaces
- igc:
- add support for multiple in-flight TX timestamps
- Broadcom:
- bnxt:
- use the unified RX page pool buffers for XDP and non-XDP
- use the NAPI skb allocation cache
- OcteonTX2:
- support Round Robin scheduling HTB offload
- TC flower offload support for SPI field
- Freescale:
- add XDP_TX feature support
- AMD:
- ionic: add support for PCI FLR event
- sfc:
- basic conntrack offload
- introduce eth, ipv4 and ipv6 pedit offloads
- ST Microelectronics:
- stmmac: maximze PTP timestamping resolution
- Virtual NICs:
- Microsoft vNIC:
- batch ringing RX queue doorbell on receiving packets
- add page pool for RX buffers
- Virtio vNIC:
- add per queue interrupt coalescing support
- Google vNIC:
- add queue-page-list mode support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add port range matching tc-flower offload
- permit enslavement to netdevices with uppers
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- convert to phylink_pcs
- Renesas:
- r8A779fx: add speed change support
- rzn1: enables vlan support
- Ethernet PHYs:
- convert mv88e6xxx to phylink_pcs
- WiFi:
- Qualcomm Wi-Fi 7 (ath12k):
- extremely High Throughput (EHT) PHY support
- RealTek (rtl8xxxu):
- enable AP mode for: RTL8192FU, RTL8710BU (RTL8188GU),
RTL8192EU and RTL8723BU
- RealTek (rtw89):
- Introduce Time Averaged SAR (TAS) support
- Connector:
- support for event filtering"
* tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1806 commits)
net: ethernet: mtk_wed: minor change in wed_{tx,rx}info_show
net: ethernet: mtk_wed: add some more info in wed_txinfo_show handler
net: stmmac: clarify difference between "interface" and "phy_interface"
r8152: add vendor/device ID pair for D-Link DUB-E250
devlink: move devlink_notify_register/unregister() to dev.c
devlink: move small_ops definition into netlink.c
devlink: move tracepoint definitions into core.c
devlink: push linecard related code into separate file
devlink: push rate related code into separate file
devlink: push trap related code into separate file
devlink: use tracepoint_enabled() helper
devlink: push region related code into separate file
devlink: push param related code into separate file
devlink: push resource related code into separate file
devlink: push dpipe related code into separate file
devlink: move and rename devlink_dpipe_send_and_alloc_skb() helper
devlink: push shared buffer related code into separate file
devlink: push port related code into separate file
devlink: push object register/unregister notifications into separate helpers
inet: fix IP_TRANSPARENT error handling
...
- one bugfix for x86 mixed mode that did not make it into v6.5
- first pass of cleanup for the EFI runtime wrappers
- some cosmetic touchups
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQQm/3uucuRGn1Dmh0wbglWLn0tXAUCZOx+LAAKCRAwbglWLn0t
XKzLAPwK8wIZ14NlC55NCtdvKEzK3N/muxKRqg2MAHfrbnREFgD9GgUxSbIEU2gz
BXQM9GLaP86qCXkZlPYktjP6RVfDYAk=
=e2mx
-----END PGP SIGNATURE-----
Merge tag 'efi-next-for-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI updates from Ard Biesheuvel:
"This primarily covers some cleanup work on the EFI runtime wrappers,
which are shared between all EFI architectures except Itanium, and
which provide some level of isolation to prevent faults occurring in
the firmware code (which runs at the same privilege level as the
kernel) from bringing down the system.
Beyond that, there is a fix that did not make it into v6.5, and some
doc fixes and dead code cleanup.
- one bugfix for x86 mixed mode that did not make it into v6.5
- first pass of cleanup for the EFI runtime wrappers
- some cosmetic touchups"
* tag 'efi-next-for-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
x86/efistub: Fix PCI ROM preservation in mixed mode
efi/runtime-wrappers: Clean up white space and add __init annotation
acpi/prmt: Use EFI runtime sandbox to invoke PRM handlers
efi/runtime-wrappers: Don't duplicate setup/teardown code
efi/runtime-wrappers: Remove duplicated macro for service returning void
efi/runtime-wrapper: Move workqueue manipulation out of line
efi/runtime-wrappers: Use type safe encapsulation of call arguments
efi/riscv: Move EFI runtime call setup/teardown helpers out of line
efi/arm64: Move EFI runtime call setup/teardown helpers out of line
efi/riscv: libstub: Fix comment about absolute relocation
efi: memmap: Remove kernel-doc warnings
efi: Remove unused extern declaration efi_lookup_mapped_addr()
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Link: https://lore.kernel.org/r/20230714174043.4040561-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZOjkTAAKCRDbK58LschI
gx32AP9gaaHFBtOYBfoenKTJfMgv1WhtQHIBas+WN9ItmBx9MAEA4gm/VyQ6oD7O
EBjJKJQ2CZ/QKw7cNacXw+l5jF7/+Q0=
=8P7g
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-08-25
We've added 87 non-merge commits during the last 8 day(s) which contain
a total of 104 files changed, 3719 insertions(+), 4212 deletions(-).
The main changes are:
1) Add multi uprobe BPF links for attaching multiple uprobes
and usdt probes, which is significantly faster and saves extra fds,
from Jiri Olsa.
2) Add support BPF cpu v4 instructions for arm64 JIT compiler,
from Xu Kuohai.
3) Add support BPF cpu v4 instructions for riscv64 JIT compiler,
from Pu Lehui.
4) Fix LWT BPF xmit hooks wrt their return values where propagating
the result from skb_do_redirect() would trigger a use-after-free,
from Yan Zhai.
5) Fix a BPF verifier issue related to bpf_kptr_xchg() with local kptr
where the map's value kptr type and locally allocated obj type
mismatch, from Yonghong Song.
6) Fix BPF verifier's check_func_arg_reg_off() function wrt graph
root/node which bypassed reg->off == 0 enforcement,
from Kumar Kartikeya Dwivedi.
7) Lift BPF verifier restriction in networking BPF programs to treat
comparison of packet pointers not as a pointer leak,
from Yafang Shao.
8) Remove unmaintained XDP BPF samples as they are maintained
in xdp-tools repository out of tree, from Toke Høiland-Jørgensen.
9) Batch of fixes for the tracing programs from BPF samples in order
to make them more libbpf-aware, from Daniel T. Lee.
10) Fix a libbpf signedness determination bug in the CO-RE relocation
handling logic, from Andrii Nakryiko.
11) Extend libbpf to support CO-RE kfunc relocations. Also follow-up
fixes for bpf_refcount shared ownership implementation,
both from Dave Marchevsky.
12) Add a new bpf_object__unpin() API function to libbpf,
from Daniel Xu.
13) Fix a memory leak in libbpf to also free btf_vmlinux
when the bpf_object gets closed, from Hao Luo.
14) Small error output improvements to test_bpf module, from Helge Deller.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (87 commits)
selftests/bpf: Add tests for rbtree API interaction in sleepable progs
bpf: Allow bpf_spin_{lock,unlock} in sleepable progs
bpf: Consider non-owning refs to refcounted nodes RCU protected
bpf: Reenable bpf_refcount_acquire
bpf: Use bpf_mem_free_rcu when bpf_obj_dropping refcounted nodes
bpf: Consider non-owning refs trusted
bpf: Ensure kptr_struct_meta is non-NULL for collection insert and refcount_acquire
selftests/bpf: Enable cpu v4 tests for RV64
riscv, bpf: Support unconditional bswap insn
riscv, bpf: Support signed div/mod insns
riscv, bpf: Support 32-bit offset jmp insn
riscv, bpf: Support sign-extension mov insns
riscv, bpf: Support sign-extension load insns
riscv, bpf: Fix missing exception handling and redundant zext for LDX_B/H/W
samples/bpf: Add note to README about the XDP utilities moved to xdp-tools
samples/bpf: Cleanup .gitignore
samples/bpf: Remove the xdp_sample_pkts utility
samples/bpf: Remove the xdp1 and xdp2 utilities
samples/bpf: Remove the xdp_rxq_info utility
samples/bpf: Remove the xdp_redirect* utilities
...
====================
Link: https://lore.kernel.org/r/20230825194319.12727-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
or aren't considered suitable for a -stable backport.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZOjuGgAKCRDdBJ7gKXxA
jkLlAQDY9sYxhQZp1PFLirUIPeOBjEyifVy6L6gCfk9j0snLggEA2iK+EtuJt2Dc
SlMfoTq29zyU/YgfKKwZEVKtPJZOHQU=
=oTcj
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2023-08-25-11-07' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"18 hotfixes. 13 are cc:stable and the remainder pertain to post-6.4
issues or aren't considered suitable for a -stable backport"
* tag 'mm-hotfixes-stable-2023-08-25-11-07' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
shmem: fix smaps BUG sleeping while atomic
selftests: cachestat: catch failing fsync test on tmpfs
selftests: cachestat: test for cachestat availability
maple_tree: disable mas_wr_append() when other readers are possible
madvise:madvise_free_pte_range(): don't use mapcount() against large folio for sharing check
madvise:madvise_free_huge_pmd(): don't use mapcount() against large folio for sharing check
madvise:madvise_cold_or_pageout_pte_range(): don't use mapcount() against large folio for sharing check
mm: multi-gen LRU: don't spin during memcg release
mm: memory-failure: fix unexpected return value in soft_offline_page()
radix tree: remove unused variable
mm: add a call to flush_cache_vmap() in vmap_pfn()
selftests/mm: FOLL_LONGTERM need to be updated to 0x100
nilfs2: fix general protection fault in nilfs_lookup_dirty_data_buffers()
mm/gup: handle cont-PTE hugetlb pages correctly in gup_must_unshare() via GUP-fast
selftests: cgroup: fix test_kmem_basic less than error
mm: enable page walking API to lock vmas during the walk
smaps: use vm_normal_page_pmd() instead of follow_trans_huge_pmd()
mm/gup: reintroduce FOLL_NUMA as FOLL_HONOR_NUMA_FAULT
* The vector ucontext extension has been extended with vlenb.
* The vector registers ELF core dump note type has been changed to avoid
aliasing with the CSR type used in embedded systems.
* Support for accessing vector registers via ptrace() has been reverted.
* Another build fix for the ISA spec changes around Zifencei/Zicsr that
manifests on some systems built with binutils-2.37 and gcc-11.2.
-----BEGIN PGP SIGNATURE-----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=bvaa
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"This is obviously not ideal, particularly for something this late in
the cycle.
Unfortunately we found some uABI issues in the vector support while
reviewing the GDB port, which has triggered a revert -- probably a
good sign we should have reviewed GDB before merging this, I guess I
just dropped the ball because I was so worried about the context
extension and libc suff I forgot. Hence the late revert.
There's some risk here as we're still exposing the vector context for
signal handlers, but changing that would have meant reverting all of
the vector support. The issues we've found so far have been fixed
already and they weren't absolute showstoppers, so we're essentially
just playing it safe by holding ptrace support for another release (or
until we get through a proper userspace code review).
Summary:
- The vector ucontext extension has been extended with vlenb
- The vector registers ELF core dump note type has been changed to
avoid aliasing with the CSR type used in embedded systems
- Support for accessing vector registers via ptrace() has been
reverted
- Another build fix for the ISA spec changes around Zifencei/Zicsr
that manifests on some systems built with binutils-2.37 and
gcc-11.2"
* tag 'riscv-for-linus-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix build errors using binutils2.37 toolchains
RISC-V: vector: export VLENB csr in __sc_riscv_v_state
RISC-V: Remove ptrace support for vectors
Add set_ptes(), update_mmu_cache_range() and flush_dcache_folio(). Change
the PG_dcache_clean flag from being per-page to per-folio.
Link: https://lkml.kernel.org/r/20230802151406.3735276-23-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tell the page table check how many PTEs & PFNs we want it to check.
Link: https://lkml.kernel.org/r/20230802151406.3735276-3-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
handle_mm_fault returning VM_FAULT_RETRY or VM_FAULT_COMPLETED means
mmap_lock has been released. However with per-VMA locks behavior is
different and the caller should still release it. To make the rules
consistent for the caller, drop the per-VMA lock when returning
VM_FAULT_RETRY or VM_FAULT_COMPLETED. Currently the only path returning
VM_FAULT_RETRY under per-VMA locks is do_swap_page and no path returns
VM_FAULT_COMPLETED for now.
[willy@infradead.org: fix riscv]
Link: https://lkml.kernel.org/r/CAJuCfpE6GWEx1rPBmNpUfoD5o-gNFz9-UFywzCE2PbEGBiVz7g@mail.gmail.com
Link: https://lkml.kernel.org/r/20230630211957.1341547-4-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hillf Danton <hdanton@sina.com>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michel Lespinasse <michel@lespinasse.org>
Cc: Minchan Kim <minchan@google.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add support unconditional bswap instruction. Since riscv is always
little-endian, just treat the unconditional scenario the same as
big-endian conversion.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Acked-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/r/20230824095001.3408573-7-pulehui@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
For LDX_B/H/W, when zext has been inserted by verifier, it'll return 1,
and no exception handling will continue. Also, when the offset is 12-bit
value, the redundant zext inserted by the verifier is not removed. Fix
both scenarios by moving down the removal of redundant zext.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/r/20230824095001.3408573-2-pulehui@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
sv57 is supported in the kernel so pgtable.h should reflect that.
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230809232218.849726-4-charlie@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Make sv48 the default address space for mmap as some applications
currently depend on this assumption. A hint address passed to mmap will
cause the largest address space that fits entirely into the hint to be
used. If the hint is less than or equal to 1<<38, an sv39 address will
be used. An exception is that if the hint address is 0, then a sv48
address will be used. After an address space is completely full, the next
smallest address space will be used.
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Link: https://lore.kernel.org/r/20230809232218.849726-2-charlie@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
With the DMA bouncing of unaligned kmalloc() buffers now in place,
enable it for riscv when RISCV_DMA_NONCOHERENT=y to allow the
kmalloc-{8,16,32,96} caches. Since RV32 doesn't enable SWIOTLB
yet, and I didn't see any dma noncoherent RV32 platforms in the
mainline, so skip RV32 now by only enabling
DMA_BOUNCE_UNALIGNED_KMALLOC if SWIOTLB is available. Once we see
such requirement on RV32, we can enable it then.
NOTE: we didn't force to create the swiotlb buffer even when the
end of RAM is within the 32-bit physical address range. That's to
say:
For RV64 with > 4GB memory, the feature is enabled.
For RV64 with <= 4GB memory, the feature isn't enabled by default. We
rely on users to pass "swiotlb=mmnn,force" where mmnn is the Number of
I/O TLB slabs, see kernel-parameters.txt for details.
Tested on Sipeed Lichee Pi 4A with 8GB DDR and Sipeed M1S BL808 Dock
board.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230718152214.2907-3-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Currently, riscv defines ARCH_DMA_MINALIGN as L1_CACHE_BYTES, I.E
64Bytes, if CONFIG_RISCV_DMA_NONCOHERENT=y. To support unified kernel
Image, usually we have to enable CONFIG_RISCV_DMA_NONCOHERENT, thus
it brings some bad effects to coherent platforms:
Firstly, it wastes memory, kmalloc-96, kmalloc-32, kmalloc-16 and
kmalloc-8 slab caches don't exist any more, they are replaced with
either kmalloc-128 or kmalloc-64.
Secondly, larger than necessary kmalloc aligned allocations results
in unnecessary cache/TLB pressure.
This issue also exists on arm64 platforms. From last year, Catalin
tried to solve this issue by decoupling ARCH_KMALLOC_MINALIGN from
ARCH_DMA_MINALIGN, limiting kmalloc() minimum alignment to
dma_get_cache_alignment() and replacing ARCH_KMALLOC_MINALIGN usage
in various drivers with ARCH_DMA_MINALIGN etc.[1]
One fact we can make use of for riscv: if the CPU doesn't support
ZICBOM or T-HEAD CMO, we know the platform is coherent. Based on
Catalin's work and above fact, we can easily solve the kmalloc align
issue for riscv: we can override dma_get_cache_alignment(), then let
it return ARCH_DMA_MINALIGN at the beginning and return 1 once we know
the underlying HW neither supports ZICBOM nor supports T-HEAD CMO.
So what about if the CPU supports ZICBOM or T-HEAD CMO, but all the
devices are dma coherent? Well, we use ARCH_DMA_MINALIGN as the
kmalloc minimum alignment, nothing changed in this case. This case
can be improved in the future.
After this patch, a simple test of booting to a small buildroot rootfs
on qemu shows:
kmalloc-96 5041 5041 96 ...
kmalloc-64 9606 9606 64 ...
kmalloc-32 5128 5128 32 ...
kmalloc-16 7682 7682 16 ...
kmalloc-8 10246 10246 8 ...
So we save about 1268KB memory. The saving will be much larger in normal
OS env on real HW platforms.
Link: https://lore.kernel.org/linux-arm-kernel/20230524171904.3967031-1-catalin.marinas@arm.com/ [1]
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230718152214.2907-2-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add support for enabling and using the binfmt_elf_fdpic program loader
on RISC-V platforms. The most important change is to setup registers
during program load to pass the mapping addresses to the new process.
One of the interesting features of the elf-fdpic loader is that it
also allows appropriately compiled ELF format binaries to be loaded on
nommu systems. Appropriate being those compiled with -pie.
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230711130754.481209-3-gerg@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Commit 883bbbffa5 ("ftrace,kcfi: Separate ftrace_stub() and
ftrace_stub_graph()") added a separate ftrace_stub_graph function for
CFI_CLANG. Add the stub to fix FUNCTION_GRAPH_TRACER compatibility
with CFI.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20230710183544.999540-11-samitolvanen@google.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
With CONFIG_CFI_CLANG, assembly functions indirectly called
from C code must be annotated with type identifiers to pass CFI
checking. Use the SYM_TYPED_START macro to add types to the
relevant functions.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20230710183544.999540-10-samitolvanen@google.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Commit f0bddf5058 ("riscv: entry: Convert to generic entry") moved
syscall handling to C code, which exposed function pointer type
mismatches that trip fine-grained forward-edge Control-Flow Integrity
(CFI) checks as syscall handlers are all called through the same
syscall_t pointer type. To fix the type mismatches, implement pt_regs
based syscall wrappers similarly to x86 and arm64.
This patch is based on arm64 syscall wrappers added in commit
4378a7d4be ("arm64: implement syscall wrappers"), where the main goal
was to minimize the risk of userspace-controlled values being used
under speculation. This may be a concern for riscv in future as well.
Following other architectures, the syscall wrappers generate three
functions for each syscall; __riscv_<compat_>sys_<name> takes a pt_regs
pointer and extracts arguments from registers, __se_<compat_>sys_<name>
is a sign-extension wrapper that casts the long arguments to the
correct types for the real syscall implementation, which is named
__do_<compat_>sys_<name>.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20230710183544.999540-9-samitolvanen@google.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Andy Chiu <andy.chiu@sifive.com> says:
We add a vlenb field in Vector context and save it with the
riscv_vstate_save() macro. It should not cause performance regression as
VLENB is a design-time constant and is frequently used by hardware.
Also, adding this field into the __sc_riscv_v_state may benifit us on a
future compatibility issue becuse a hardware may have writable VLENB.
Adding and saving VLENB have an immediate benifit as it gives ptrace a
better view of the Vector extension and makes it possible to reconstruct
Vector register files from the dump without doing an additional csr read.
This patchset also sync the number of note types between us and gdb for
riscv to solve a conflicting note.
This is not an ABI break given that 6.5 has not been released yet.
* b4-shazam-merge:
RISC-V: vector: export VLENB csr in __sc_riscv_v_state
RISC-V: Remove ptrace support for vectors
Link: https://lore.kernel.org/r/20230816155450.26200-1-andy.chiu@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Some V configurations implicitly turn on '-fno-omit-frame-pointer',
but leaving FRAME_POINTER disabled. This makes it hard to reason about
the FRAME_POINTER config, and also triggers build failures introduced
in by the commit in the Fixes: tag.
Select FRAME_POINTER explicitly for these configurations.
Fixes: ebc9cb03b2 ("riscv: stack: Fixup independent softirq stack for CONFIG_FRAME_POINTER=n")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230823082845.354839-1-bjorn@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
VLENB is critical for callers of ptrace to reconstruct Vector register
files from the register dump of NT_RISCV_VECTOR. Also, future systems
may will have a writable VLENB, so add it now to potentially save future
compatibility issue.
Fixes: 0c59922c76 ("riscv: Add ptrace vector support")
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Link: https://lore.kernel.org/r/20230816155450.26200-3-andy.chiu@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
We've found two bugs here: NT_RISCV_VECTOR steps on NT_RISCV_CSR (which
is only for embedded), and we don't have vlenb in the core dumps. Given
that we've have a pair of bugs croup up as part of the GDB review we've
probably got other issues, so let's just cut this for 6.5 and get it
right.
Fixes: 0c59922c76 ("riscv: Add ptrace vector support")
Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Link: https://lore.kernel.org/r/20230816155450.26200-2-andy.chiu@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
T-Head:
Add a second minimal devicetree for the second board using the th1520
SoC, the BeagleV Ahead. As with the Lichee Pi 4a, this is sufficient
only for booting to a console, with work on the mmc, clocks and ethernet
sides of things under way. A relicense to a dual licence for the
existing devicetree files is also done, for good measure.
RISC-V Devicetrees for v6.6-pt2
StarFive:
Fix the sort order of some nodes that I resolved incorrectly during a
merge conflict.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZOCDsgAKCRB4tDGHoIJi
0mEDAQDc1z032ZsKJSE/WBV0R8hw47RZoP22xHCP3d38vDfP3wEAsF6Kc0U+t8TQ
6CNGHUNpEkVJIdj/wOL8Zk0gV/GdLAA=
=F146
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmTkE8sACgkQYKtH/8kJ
Uido2A//aml2dM6R2eG3Nz5jX0xtAwE5xGix/pHW0eG4Z3c3YFsb6R0cnjO4DLjg
MwPrfQl9M7ee2obKsUqOAnD7QgZnP9ewSCOrPqWFn2YKcmA2mZcby4u1qd1m2+Gc
UZrvXqoI1ixK4gTxfcfBJI//8ui6AOHMtDvkWlRXCbcMCEruF5NCGNHkDPxve44z
8R/PJUAXEkBUG7mEgnQKTuRgn/Gwgrn0cZKc7YNehAq0SAeihyiRqNNjD/+ftTrl
xVrU1RLY/P6dxMP1l3wCxhhM7LPqWSzNflNgAu37A7PmzieYu/FExnW/NuQ3m9UA
tzeMGUS4FWkvJKRVwYmzY+SpT4/9SgswUiRoJ6HKCxC63+TMLH6BBJ0HsTFnctq3
mvjqx5kcqe9RVdrJBPSbYuH7xdbvWD2I+m7IQnuOvkwPghRuBf2q6HQ2L2ah7WlJ
ZOcJ82/kUx/Cb5o0hDMvKVfU+ZUGoDPWKfqpqVfftgh5TTOoZpmMfMclwSG2zw3/
PoXLE+dnYCBtynAYAbX/Z5YPIdV3WL5/TJEAVIgyFBKPcUsi0Hc841gkymur1lCr
fd+scjRCON1zV3EILI/CDEwXToyVlPqMSznjj+nm3sV05tCUA1GQ8I/RsnwbFSsP
/gNtPJ9fJRKtfTrU7lLdaaauk+aoRvRud3XQpwYmCfWLCDJ+ciQ=
=3ypd
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.6-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6 Part 2
T-Head:
Add a second minimal devicetree for the second board using the th1520
SoC, the BeagleV Ahead. As with the Lichee Pi 4a, this is sufficient
only for booting to a console, with work on the mmc, clocks and ethernet
sides of things under way. A relicense to a dual licence for the
existing devicetree files is also done, for good measure.
RISC-V Devicetrees for v6.6-pt2
StarFive:
Fix the sort order of some nodes that I resolved incorrectly during a
merge conflict.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
riscv: dts: starfive: fix jh7110 qspi sort order
Link: https://lore.kernel.org/r/20230819-unwieldy-railing-9bba2b176aa7@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is only one Kconfig user of CONFIG_EMBEDDED and it can be switched
to EXPERT or "if !ARCH_MULTIPLATFORM" (suggested by Arnd).
Link: https://lkml.kernel.org/r/20230816055010.31534-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com> [RISC-V]
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Brian Cain <bcain@quicinc.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
PG_dcache_clean is used in asm/hugetlb.h but defined in asm/cacheflush.h:
builds rely on an accident of that being included via linux/mempolicy.h,
but better include it directly (like arch/sh/include/asm/hugetlb.h does).
Link: https://lkml.kernel.org/r/84bd3b96-8dbe-51b1-d7d1-6e4f9d8937d8@google.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
As part of the conversions to replace pgtable constructor/destructors with
ptdesc equivalents, convert various page table functions to use ptdescs.
Some of the functions use the *get*page*() helper functions. Convert
these to use pagetable_alloc() and ptdesc_address() instead to help
standardize page tables further.
Link: https://lkml.kernel.org/r/20230807230513.102486-27-vishal.moola@gmail.com
Signed-off-by: Vishal Moola (Oracle) <vishal.moola@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Guo Ren <guoren@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
walk_page_range() and friends often operate under write-locked mmap_lock.
With introduction of vma locks, the vmas have to be locked as well during
such walks to prevent concurrent page faults in these areas. Add an
additional member to mm_walk_ops to indicate locking requirements for the
walk.
The change ensures that page walks which prevent concurrent page faults
by write-locking mmap_lock, operate correctly after introduction of
per-vma locks. With per-vma locks page faults can be handled under vma
lock without taking mmap_lock at all, so write locking mmap_lock would
not stop them. The change ensures vmas are properly locked during such
walks.
A sample issue this solves is do_mbind() performing queue_pages_range()
to queue pages for migration. Without this change a concurrent page
can be faulted into the area and be left out of migration.
Link: https://lkml.kernel.org/r/20230804152724.3090321-2-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Suggested-by: Jann Horn <jannh@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michel Lespinasse <michel@lespinasse.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Only the arch_efi_call_virt() macro that some architectures override
needs to be a macro, given that it is variadic and encapsulates calls
via function pointers that have different prototypes.
The associated setup and teardown code are not special in this regard,
and don't need to be instantiated at each call site. So turn them into
ordinary C functions and move them out of line.
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/sfc/tc.c
fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
3bf969e88a ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* A fix to avoid excessive rejections from seccomp RET_ERRNO rules.
* A fix for compressed jal/jalr decoding.
* A pair of fixes for independent irq/softirq stacks on kernels built
with CONFIG_FRAME_POINTER=n.
* A fix to avoid a hang handling uaccess fixups.
* Another build fix for toolchain ISA strings, this time for Zicsr and
Zifenci on old GNU toolchains.
-----BEGIN PGP SIGNATURE-----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=LtPj
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- avoid excessive rejections from seccomp RET_ERRNO rules
- compressed jal/jalr decoding fix
- fixes for independent irq/softirq stacks on kernels built with
CONFIG_FRAME_POINTER=n
- avoid a hang handling uaccess fixups
- another build fix for toolchain ISA strings, this time for Zicsr and
Zifenci on old GNU toolchains
* tag 'riscv-for-linus-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Handle zicsr/zifencei issue between gcc and binutils
riscv: uaccess: Return the number of bytes effectively not copied
riscv: stack: Fixup independent softirq stack for CONFIG_FRAME_POINTER=n
riscv: stack: Fixup independent irq stack for CONFIG_FRAME_POINTER=n
riscv: correct riscv_insn_is_c_jr() and riscv_insn_is_c_jalr()
riscv: entry: set a0 = -ENOSYS only when syscall != -1
The Kconfig refactor to consolidate KEXEC and CRASH options utilized
option names of the form ARCH_SUPPORTS_<option>. Thus rename the
ARCH_HAS_KEXEC_PURGATORY to ARCH_SUPPORTS_KEXEC_PURGATORY to follow
the same.
Link: https://lkml.kernel.org/r/20230712161545.87870-15-eric.devolder@oracle.com
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kexec and crash kernel options are provided in the common
kernel/Kconfig.kexec. Utilize the common options and provide
the ARCH_SUPPORTS_ and ARCH_SELECTS_ entries to recreate the
equivalent set of KEXEC and CRASH options.
Link: https://lkml.kernel.org/r/20230712161545.87870-12-eric.devolder@oracle.com
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Arm disabled hugetlb vmemmap optimization [1] because hugetlb vmemmap
optimization includes an update of both the permissions (writeable to
read-only) and the output address (pfn) of the vmemmap ptes. That is not
supported without unmapping of pte(marking it invalid) by some
architectures.
With DAX vmemmap optimization we don't require such pte updates and
architectures can enable DAX vmemmap optimization while having hugetlb
vmemmap optimization disabled. Hence split DAX optimization support into
a different config.
s390, loongarch and riscv don't have devdax support. So the DAX config is
not enabled for them. With this change, arm64 should be able to select
DAX optimization
[1] commit 060a2c92d1 ("arm64: mm: hugetlb: Disable HUGETLB_PAGE_OPTIMIZE_VMEMMAP")
Link: https://lkml.kernel.org/r/20230724190759.483013-8-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Joao Martins <joao.m.martins@oracle.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "Handle most file-backed faults under the VMA lock", v3.
This patchset adds the ability to handle page faults on parts of files
which are already in the page cache without taking the mmap lock.
This patch (of 10):
Provide lock_vma_under_rcu() when CONFIG_PER_VMA_LOCK is not defined to
eliminate ifdefs in the users.
Link: https://lkml.kernel.org/r/20230724185410.1124082-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20230724185410.1124082-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Remove unused addr in __page_table_check_pud_set and
page_table_check_pud_set.
Link: https://lkml.kernel.org/r/20230713172636.1705415-9-shikemeng@huaweicloud.com
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Remove unused addr in __page_table_check_pmd_set and
page_table_check_pmd_set.
Link: https://lkml.kernel.org/r/20230713172636.1705415-8-shikemeng@huaweicloud.com
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Remove unused addr in __page_table_check_pte_set and
page_table_check_pte_set.
Link: https://lkml.kernel.org/r/20230713172636.1705415-7-shikemeng@huaweicloud.com
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Remove unused addr in page_table_check_pmd_clear and
__page_table_check_pmd_clear.
Link: https://lkml.kernel.org/r/20230713172636.1705415-5-shikemeng@huaweicloud.com
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Remove unused addr in page_table_check_pte_clear and
__page_table_check_pte_clear.
Link: https://lkml.kernel.org/r/20230713172636.1705415-4-shikemeng@huaweicloud.com
Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Just one partial revert for a commit from the merge window
that caused annoying behavior when building old kernels on
arm64 hosts.
-----BEGIN PGP SIGNATURE-----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=tTzL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fix-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic regression fix from Arnd Bergmann:
"Just one partial revert for a commit from the merge window that caused
annoying behavior when building old kernels on arm64 hosts"
* tag 'asm-generic-fix-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: partially revert "Unify uapi bitsperlong.h for arm64, riscv and loongarch"
Wrap kvm_{gfn,hva}_range.pte in a union so that future notifier events can
pass event specific information up and down the stack without needing to
constantly expand and churn the APIs. Lockless aging of SPTEs will pass
around a bitmap, and support for memory attributes will pass around the
new attributes for the range.
Add a "KVM_NO_ARG" placeholder to simplify handling events without an
argument (creating a dummy union variable is midly annoying).
Opportunstically drop explicit zero-initialization of the "pte" field, as
omitting the field (now a union) has the same effect.
Cc: Yu Zhao <yuzhao@google.com>
Link: https://lore.kernel.org/all/CAOUHufagkd2Jk3_HrVoFFptRXM=hX2CV8f+M-dka-hJU4bP8kw@mail.gmail.com
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Acked-by: Yu Zhao <yuzhao@google.com>
Link: https://lore.kernel.org/r/20230729004144.1054885-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Unifying the asm-generic headers across 32-bit and 64-bit architectures
based on the compiler provided macros was a good idea and appears to work
with all user space, but it caused a regression when building old kernels
on systems that have the new headers installed in /usr/include, as this
combination trips an inconsistency in the kernel's own tools/include
headers that are a mix of userspace and kernel-internal headers.
This affects kernel builds on arm64, riscv64 and loongarch64 systems that
might end up using the "#define __BITS_PER_LONG 32" default from the old
tools headers. Backporting the commit into stable kernels would address
this, but it would still break building kernels without that backport,
and waste time for developers trying to understand the problem.
arm64 build machines are rather common, and on riscv64 this can also
happen in practice, but loongarch64 is probably new enough to not
be used much for building old kernels, so only revert the bits
for arm64 and riscv.
Link: https://lore.kernel.org/all/20230731160402.GB1823389@dev-arch.thelio-3990X/
Reported-by: Nathan Chancellor <nathan@kernel.org>
Fixes: 8386f58f8d ("asm-generic: Unify uapi bitsperlong.h for arm64, riscv and loongarch")
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move kvm_arch_flush_remote_tlbs_memslot() to common code and drop
"arch_" from the name. kvm_arch_flush_remote_tlbs_memslot() is just a
range-based TLB invalidation where the range is defined by the memslot.
Now that kvm_flush_remote_tlbs_range() can be called from common code we
can just use that and drop a bunch of duplicate code from the arch
directories.
Note this adds a lockdep assertion for slots_lock being held when
calling kvm_flush_remote_tlbs_memslot(), which was previously only
asserted on x86. MIPS has calls to kvm_flush_remote_tlbs_memslot(),
but they all hold the slots_lock, so the lockdep assertion continues to
hold true.
Also drop the CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT ifdef gating
kvm_flush_remote_tlbs_memslot(), since it is no longer necessary.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Acked-by: Anup Patel <anup@brainfault.org>
Acked-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230811045127.3308641-7-rananta@google.com
The BeagleV Ahead single board computer uses the T-Head TH1520 SoC.
Add a minimal device tree to support basic uart/gpio/dmac drivers so
that a user can boot to a basic shell.
Link: https://beagleboard.org/beaglev-ahead
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
On riscv, the current crash kernel allocation logic is trying to
allocate within 32bit addressible memory region by default, if
failed, try to allocate without 4G restriction.
In need of saving DMA zone memory while allocating a relatively large
crash kernel region, allocating the reserved memory top down in
high memory, without overlapping the DMA zone, is a mature solution.
Here introduce the parameter option crashkernel=X,[high,low].
One can reserve the crash kernel from high memory above DMA zone range
by explicitly passing "crashkernel=X,high"; or reserve a memory range
below 4G with "crashkernel=X,low".
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Acked-by: Guo Ren <guoren@kernel.org>
Acked-by: Baoquan He <bhe@redhat.com>
Link: https://lore.kernel.org/r/20230726175000.2536220-2-chenjiahao16@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
It was reported that the riscv kernel hangs while executing the test
in [1].
Indeed, the test hangs when trying to write a buffer to a file. The
problem is that the riscv implementation of raw_copy_from_user() does not
return the correct number of bytes not written when an exception happens
and is fixed up, instead it always returns the initial size to copy,
even if some bytes were actually copied.
generic_perform_write() pre-faults the user pages and bails out if nothing
can be written, otherwise it will access the userspace buffer: here the
riscv implementation keeps returning it was not able to copy any byte
though the pre-faulting indicates otherwise. So generic_perform_write()
keeps retrying to access the user memory and ends up in an infinite
loop.
Note that before the commit mentioned in [1] that introduced this
regression, it worked because generic_perform_write() would bail out if
only one byte could not be written.
So fix this by returning the number of bytes effectively not written in
__asm_copy_[to|from]_user() and __clear_user(), as it is expected.
Link: https://lore.kernel.org/linux-riscv/20230309151841.bomov6hq3ybyp42a@debian/ [1]
Fixes: ebcbd75e39 ("riscv: Fix the bug in memory access fixup code")
Reported-by: Bo YU <tsu.yubo@gmail.com>
Closes: https://lore.kernel.org/linux-riscv/20230309151841.bomov6hq3ybyp42a@debian/#t
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Closes: https://lore.kernel.org/linux-riscv/ZNOnCakhwIeue3yr@aurel32.net/
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Link: https://lore.kernel.org/r/20230811150604.1621784-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The independent softirq stack uses s0 to save & restore sp, but s0 would
be corrupted when CONFIG_FRAME_POINTER=n. So add s0 in the clobber list
to fix the problem.
Fixes: dd69d07a5a ("riscv: stack: Support HAVE_SOFTIRQ_ON_OWN_STACK")
Cc: stable@vger.kernel.org
Reported-by: Zhangjin Wu <falcon@tinylab.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Tested-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20230716001506.3506041-3-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The independent irq stack uses s0 to save & restore sp, but s0 would be
corrupted when CONFIG_FRAME_POINTER=n. So add s0 in the clobber list to
fix the problem.
Fixes: 163e76cc6e ("riscv: stack: Support HAVE_IRQ_EXIT_ON_IRQ_STACK")
Cc: stable@vger.kernel.org
Reported-by: Zhangjin Wu <falcon@tinylab.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Tested-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20230716001506.3506041-2-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The instructions c.jr and c.jalr must have rs1 != 0, but
riscv_insn_is_c_jr() and riscv_insn_is_c_jalr() do not check for this. So,
riscv_insn_is_c_jr() can match a reserved encoding, while
riscv_insn_is_c_jalr() can match the c.ebreak instruction.
Rewrite them with check for rs1 != 0.
Signed-off-by: Nam Cao <namcaov@gmail.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Fixes: ec5f908775 ("RISC-V: Move riscv_insn_is_* macros into a common header")
Link: https://lore.kernel.org/r/20230731183925.152145-1-namcaov@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
When we test seccomp with 6.4 kernel, we found errno has wrong value.
If we deny NETLINK_AUDIT with EAFNOSUPPORT, after f0bddf5058, we will
get ENOSYS instead. We got same result with commit 9c2598d435 ("riscv:
entry: Save a0 prior syscall_enter_from_user_mode()").
After analysing code, we think that regs->a0 = -ENOSYS should only be
executed when syscall != -1. In __seccomp_filter, when seccomp rejected
this syscall with specified errno, they will set a0 to return number as
syscall ABI, and then return -1. This return number is finally pass as
return number of syscall_enter_from_user_mode, and then is compared with
NR_syscalls after converted to ulong (so it will be ULONG_MAX). The
condition syscall < NR_syscalls will always be false, so regs->a0 = -ENOSYS
is always executed. It covered a0 set by seccomp, so we always get
ENOSYS when match seccomp RET_ERRNO rule.
Fixes: f0bddf5058 ("riscv: entry: Convert to generic entry")
Reported-by: Felix Yan <felixonmars@archlinux.org>
Co-developed-by: Ruizhe Pan <c141028@gmail.com>
Signed-off-by: Ruizhe Pan <c141028@gmail.com>
Co-developed-by: Shiqi Zhang <shiqi@isrc.iscas.ac.cn>
Signed-off-by: Shiqi Zhang <shiqi@isrc.iscas.ac.cn>
Signed-off-by: Celeste Liu <CoelacanthusHex@gmail.com>
Tested-by: Felix Yan <felixonmars@archlinux.org>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230801141607.435192-1-CoelacanthusHex@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Emil pointed out that "13010000 sorts after 12070000". Reshuffle the
entries to be in-order.
Reported-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZNiusAAKCRB4tDGHoIJi
0u5JAP90hKhmPTWqxdRpnFrWi83k9RX4J6k5LHrqyt3e0sZ0HAD+JNiv4i4j8fDv
fm7usmraq8B2zLaV/AFmj9kiqdx0JgU=
=AH1c
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=+tgF
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: (26 commits)
riscv: dts: starfive: jh7110: Fix GMAC configuration
riscv: dts: starfive - Add hwrng node for JH7110 SoC
riscv: dts: starfive - Add crypto and DMA node for JH7110
riscv: dts: starfive: Add mmc nodes on VisionFive 2 board
riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060
riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC
riscv: dts: starfive: jh7110: add the node and pins configuration for tdm
riscv: dts: starfive: jh7110: add dma controller node
riscv: dts: starfive: Add spi node and pins configuration
riscv: dts: starfive: Add USB dts node for JH7110
riscv: dts: starfive: Add USB and PCIe PHY nodes for JH7110
riscv: dts: starfive: jh7110: Add temperature sensor node and thermal-zones
riscv: dts: starfive: jh7100: Add temperature sensor node and thermal-zones
riscv: dts: starfive: visionfive 2: Add configuration of gmac and phy
riscv: dts: starfive: jh7110: Add ethernet device nodes
riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
riscv: dts: starfive: jh7110: Add syscon nodes
riscv: dts: starfive: jh7110: Add STGCRG/ISPCRG/VOUTCRG nodes
riscv: dts: starfive: jh7110: Add DVP and HDMI TX pixel external clocks
dt-bindings: clock: Add StarFive JH7110 Video-Output clock and reset generator
...
Link: https://lore.kernel.org/r/20230813-naturist-fragment-ac7d10c453ba@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Allwinner D1, T113 provide two CAN controllers that are variants
of the R40 controller.
I have tested support for these controllers on two boards:
- A Lichee Panel RV 86 Panel running a D1 chip
- A Mango Pi MQ Dual running a T113-s3 chip
Both of these fully support both CAN controllers.
Signed-off-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/r/20230807191952.2019208-1-contact@jookia.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
- Add Clocked Serial Interface (CSI) support for the RZ/V2M SoC,
- Add PMIC, RTC, and PWM support for the RZ/G2L, RZ/G2LC, and RZ/V2L
SMARC EVK development boards,
- Add PWM (MTU3a) support for the RZ/G2UL and RZ/Five SoCs,
- Add External interrupt (INTC-EX) support for the R-Car S4-8 SoC,
- Add LED support for the Spider development board,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZMOojAAKCRCKwlD9ZEnx
cDCFAPsHgAfrHWFiL0x6AhhNOesqKAWvplGhosT0zArv7TNZtwEAq5QXAy3xFHS6
v9HA2cskx4OaGCDrdNqz7DBj30IyZQM=
=mRJ6
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=GODg
-----END PGP SIGNATURE-----
Merge tag 'renesas-dts-for-v6.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.6
- Add Clocked Serial Interface (CSI) support for the RZ/V2M SoC,
- Add PMIC, RTC, and PWM support for the RZ/G2L, RZ/G2LC, and RZ/V2L
SMARC EVK development boards,
- Add PWM (MTU3a) support for the RZ/G2UL and RZ/Five SoCs,
- Add External interrupt (INTC-EX) support for the R-Car S4-8 SoC,
- Add LED support for the Spider development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: spider-cpu: Add GP LEDs
arm64: dts: renesas: r8a779f0: Add INTC-EX node
arm64: dts: renesas: rzg2ul-smarc: Add support for enabling MTU3
arm64: dts: renesas: r9a07g043: Add MTU3a node
ARM dts: renesas: armadillo800eva: Switch to enable-gpios
arm64: dts: renesas: rzg2lc-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: rzg2lc-smarc-som: Add PHY interrupt support for ETH0
riscv: dts: renesas: Clean up dtbs_check W=1 warning due to empty phy node
arm64: dts: renesas: rzg2lc-smarc: Add support for enabling MTU3
arm64: dts: renesas: rzg2l-smarc: Add support for enabling MTU3
arm64: dts: renesas: Add missing space before {
ARM: dts: renesas: Add missing space before {
arm64: dts: renesas: Minor whitespace cleanup around '='
arm64: dts: renesas: rzg2l-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: r9a09g011: Add CSI nodes
arm64: dts: renesas: rzg2l: Fix txdv-skew-psec typos
arm64: dts: renesas: rzg2l: Update overfow/underflow IRQ names for MTU3 channels
Link: https://lore.kernel.org/r/cover.1690545144.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Fixes for a pair of kexec_file_load() failures.
* A fix to ensure the direct mapping is PMD-aligned.
* A fix for CPU feature detection on SMP=n
* The MMIO ordering fences have been strengthened to ensure ordering
WRT delay().
* Fixes for a pair of -Wmissing-variable-declarations warnings.
* A fix to avoid PUD mappings in vmap on sv39.
* flush_cache_vmap() now flushes the TLB to avoid issues on systems that
cache invalid mappings.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEKzw3R0RoQ7JKlDp6LhMZ81+7GIkFAmTWVmUTHHBhbG1lckBk
YWJiZWx0LmNvbQAKCRAuExnzX7sYiVQXD/9BeoO5cwavjj7OH7I4DG9LZ3Gs+4j7
tHFlE2jSBiqrkAfl8bdTYKagZdyg8WoswnaekeahcxnPFmrDl8Z+uqqAmf1Oy9Lg
IMcaJL1YjPTK0sTs4uUrYr8TOFY3TrT8nhU5BwwUr/MWLFkiZsyUZbo8BoQlF06K
xNcKfjxLSytkHitnhZXDYrHusCKRYX1OfvLMroxbRqu1bVqkKo0PvBwl5aSjhrp4
EqyjAkJJkqq87OCUtNRHRbDSa/9FXE+bwdRg7gElVCRza81J9XfGTc7Dv1vvfElb
LpUMyaNU0pR8eobCfUMcDxm+0PyaB3h9b+1oLfnRdmAwnNx+ObobygR2cONCRrJ6
mwDcc1tw5bca29NZ8xJacKrpxPZ9TNi2CJnjsnx71eHAeUmMxbWRchHceOLH7uZo
4fg59knQQKl//vkxmMumOBlg83qs3g8YlYgoe/PF9oI5kWJWeglyGjSJ9YfsCFpK
Y4fGqZFg2FJUZY8mM9yvRoH0k36UMETfvZGgXgFscMUMeJfHUAshQMQHKIx5hWbR
3iL48cY8RtPsjfUh7NdaAJESF89v/ByJUTnAXG0JTv2GGO2XQVQ11UfnaBsdUB7C
IqQvLn7vmoGZslxTmAqlrwN/v9CTPBkXBXUOJXr7bJ+hbWXr3OY2vmJZklY6Jx8G
Mv0Mez3Y9KOmSg==
=ZUbT
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- Fixes for a pair of kexec_file_load() failures
- A fix to ensure the direct mapping is PMD-aligned
- A fix for CPU feature detection on SMP=n
- The MMIO ordering fences have been strengthened to ensure ordering
WRT delay()
- Fixes for a pair of -Wmissing-variable-declarations warnings
- A fix to avoid PUD mappings in vmap on sv39
- flush_cache_vmap() now flushes the TLB to avoid issues on systems
that cache invalid mappings
* tag 'riscv-for-linus-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Implement flush_cache_vmap()
riscv: Do not allow vmap pud mappings for 3-level page table
riscv: mm: fix 2 instances of -Wmissing-variable-declarations
riscv,mmio: Fix readX()-to-delay() ordering
riscv: Fix CPU feature detection with SMP disabled
riscv: Start of DRAM should at least be aligned on PMD size for the direct mapping
riscv/kexec: load initrd high in available memory
riscv/kexec: handle R_RISCV_CALL_PLT relocation type
The RISC-V kernel needs a sfence.vma after a page table modification: we
used to rely on the vmalloc fault handling to emit an sfence.vma, but
commit 7d3332be01 ("riscv: mm: Pre-allocate PGD entries for
vmalloc/modules area") got rid of this path for 64-bit kernels, so now we
need to explicitly emit a sfence.vma in flush_cache_vmap().
Note that we don't need to implement flush_cache_vunmap() as the generic
code should emit a flush tlb after unmapping a vmalloc region.
Fixes: 7d3332be01 ("riscv: mm: Pre-allocate PGD entries for vmalloc/modules area")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230725132246.817726-1-alexghiti@rivosinc.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The vmalloc_fault() path was removed and to avoid syncing the vmalloc PGD
mappings, they are now preallocated. But if the kernel can use a PUD
mapping (which in sv39 is actually a PGD mapping) for large vmalloc
allocation, it will free the current unused preallocated PGD mapping and
install a new leaf one. Since there is no sync anymore, some page tables
lack this new mapping and that triggers a panic.
So only allow PUD mappings for sv48 and sv57.
Fixes: 7d3332be01 ("riscv: mm: Pre-allocate PGD entries for vmalloc/modules area")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230808130709.1502614-1-alexghiti@rivosinc.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the mmc nodes for the StarFive JH7110 SoC.
Set mmc0 node to emmc and set mmc1 node to sd.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Enable DCDC1 node for vmmc-supply and enable ALDO4 node for
vqmmc-supply.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
KVM_GET_REG_LIST API will return all registers that are available to
KVM_GET/SET_ONE_REG APIs. It's very useful to identify some platform
regression issue during VM migration.
Since this API was already supported on arm64, it is straightforward
to enable it on riscv with similar code structure.
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
I'm looking to enable -Wmissing-variable-declarations behind W=1. 0day
bot spotted the following instance in ARCH=riscv builds:
arch/riscv/mm/init.c:276:7: warning: no previous extern declaration
for non-static variable 'trampoline_pg_dir'
[-Wmissing-variable-declarations]
276 | pgd_t trampoline_pg_dir[PTRS_PER_PGD] __page_aligned_bss;
| ^
arch/riscv/mm/init.c:276:1: note: declare 'static' if the variable is
not intended to be used outside of this translation unit
276 | pgd_t trampoline_pg_dir[PTRS_PER_PGD] __page_aligned_bss;
| ^
arch/riscv/mm/init.c:279:7: warning: no previous extern declaration
for non-static variable 'early_pg_dir'
[-Wmissing-variable-declarations]
279 | pgd_t early_pg_dir[PTRS_PER_PGD] __initdata __aligned(PAGE_SIZE);
| ^
arch/riscv/mm/init.c:279:1: note: declare 'static' if the variable is
not intended to be used outside of this translation unit
279 | pgd_t early_pg_dir[PTRS_PER_PGD] __initdata __aligned(PAGE_SIZE);
| ^
These symbols are referenced by more than one translation unit, so make
sure they're both declared and include the correct header for their
declarations. Finally, sort the list of includes to help keep them tidy.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/llvm/202308081000.tTL1ElTr-lkp@intel.com/
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20230808-riscv_static-v2-1-2a1e2d2c7a4f@google.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Section 2.1 of the Platform Specification [1] states:
Unless otherwise specified by a given I/O device, I/O devices are on
ordering channel 0 (i.e., they are point-to-point strongly ordered).
which is not sufficient to guarantee that a readX() by a hart completes
before a subsequent delay() on the same hart (cf. memory-barriers.txt,
"Kernel I/O barrier effects").
Set the I(nput) bit in __io_ar() to restore the ordering, align inline
comments.
[1] https://github.com/riscv/riscv-platform-specs
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20230803042738.5937-1-parri.andrea@gmail.com
Fixes: fab957c11e ("RISC-V: Atomic and Locking Code")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
commit 914d6f44fc ("RISC-V: only iterate over possible CPUs in ISA
string parser") changed riscv_fill_hwcap() from iterating over CPU DT
nodes to iterating over logical CPU IDs. Since this function runs long
before cpu_dev_init() creates CPU devices, it hits the fallback path in
of_cpu_device_node_get(), which itself iterates over the DT nodes,
searching for a node with the requested CPU ID. (Incidentally, this
makes riscv_fill_hwcap() now take quadratic time.)
riscv_fill_hwcap() passes a logical CPU ID to of_cpu_device_node_get(),
which uses the arch_match_cpu_phys_id() hook to translate the logical ID
to a physical ID as found in the DT.
arch_match_cpu_phys_id() has a generic weak definition, and RISC-V
provides a strong definition using cpuid_to_hartid_map(). However, the
RISC-V specific implementation is located in arch/riscv/kernel/smp.c,
and that file is only compiled when SMP is enabled.
As a result, when SMP is disabled, the generic definition is used, and
riscv_isa gets initialized based on the ISA string of hart 0, not the
boot hart. On FU740, this means has_fpu() returns false, and userspace
crashes when trying to use floating-point instructions.
Fix this by moving arch_match_cpu_phys_id() to a file which is always
compiled.
Fixes: 70114560b2 ("RISC-V: Add RISC-V specific arch_match_cpu_phys_id")
Fixes: 914d6f44fc ("RISC-V: only iterate over possible CPUs in ISA string parser")
Reported-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230803012608.3540081-1-samuel.holland@sifive.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Make two nonfunctional changes to the vector get/set vector reg
functions and their supporting function for simplification and
readability. The first is to not pass KVM_REG_RISCV_VECTOR, but
rather integrate it directly into the masking. The second is to
rename reg_val to reg_addr where and address is used instead of
a value.
Also opportunistically touch up some of the code formatting for
a third nonfunctional change.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
kvm_riscv_vcpu_(get/set)_reg_vector() now returns ENOENT if V is not
available, EINVAL if reg type is not of VECTOR type, and any error that
might be thrown by kvm_riscv_vcpu_vreg_addr().
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
riscv_vcpu_set_isa_ext_single() will prevent any write of isa_ext regs
if the vcpu already started spinning.
But if there's no extension state (enabled/disabled) made by the
userspace, there's no need to -EBUSY out - we can treat the operation as
a no-op.
zicbom/zicboz_block_size, ISA config reg and mvendorid/march/mimpid
already works in a more permissive manner w.r.t userspace writes being a
no-op, so let's do the same with isa_ext writes.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Right now we do not allow any write in mvendorid/marchid/mimpid if the
vcpu already started, preventing these regs to be changed.
However, if userspace doesn't change them, an alternative is to consider
the reg write a no-op and avoid erroring out altogether. Userpace can
then be oblivious about KVM internals if no changes were intended in the
first place.
Allow the same form of 'lazy writing' that registers such as
zicbom/zicboz_block_size supports: avoid erroring out if userspace makes
no changes in mvendorid/marchid/mimpid during reg write.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
kvm_riscv_vcpu_set_reg_config() will return -EBUSY if the ISA config reg
is being written after the VCPU ran at least once.
The same restriction isn't placed in kvm_riscv_vcpu_get_reg_config(), so
there's a chance that we'll -EBUSY out on an ISA config reg write even
if the userspace intended no changes to it.
We'll allow the same form of 'lazy writing' that registers such as
zicbom/zicboz_block_size supports: avoid erroring out if userspace made
no changes to the ISA config reg.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
vcpu_set_reg_config() and vcpu_set_reg_isa_ext() is throwing an
EOPNOTSUPP error when !vcpu->arch.ran_atleast_once. In similar cases
we're throwing an EBUSY error, like in mvendorid/marchid/mimpid
set_reg().
EOPNOTSUPP has a conotation of finality. EBUSY is more adequate in this
case since its a condition/error related to the vcpu lifecycle.
Change these EOPNOTSUPP instances to EBUSY.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The KVM_REG_RISCV_TIMER_REG can be read via get_one_reg(). But trying to
write anything in this reg via set_one_reg() results in an EOPNOTSUPP.
Change the API to behave like cbom_block_size: instead of always
erroring out with EOPNOTSUPP, allow userspace to write the same value
(riscv_timebase) back, throwing an EINVAL if a different value is
attempted.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
zicbom_block_size and zicboz_block_size have a peculiar API: they can be
read via get_one_reg() but any write will return a EOPNOTSUPP.
It makes sense to return a 'not supported' error since both values can't
be changed, but as far as userspace goes they're regs that are throwing
the same EOPNOTSUPP error even if they were read beforehand via
get_one_reg(), even if the same read value is being written back.
EOPNOTSUPP is also returned even if ZICBOM/ZICBOZ aren't enabled in the
host.
Change both to work more like their counterparts in get_one_reg() and
return -ENOENT if their respective extensions aren't available. After
that, check if the userspace is written a valid value (i.e. the host
value). Throw an -EINVAL if that's not case, let it slide otherwise.
This allows both regs to be read/written by userspace in a 'lazy'
manner, as long as the userspace doesn't change the reg vals.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Following a similar logic as the previous patch let's minimize the EINVAL
usage in *_one_reg() APIs by using ENOENT when an extension that
implements the reg is not available.
For consistency we're also replacing an EOPNOTSUPP instance that should
be an ENOENT since it's an "extension is not available" error.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
get_one_reg() and set_one_reg() are returning EINVAL errors for almost
everything: if a reg doesn't exist, if a reg ID is malformatted, if the
associated CPU extension that implements the reg isn't present in the
host, and for set_one_reg() if the value being written is invalid.
This isn't wrong according to the existing KVM API docs (EINVAL can be
used when there's no such register) but adding more ENOENT instances
will make easier for userspace to understand what went wrong.
Existing userspaces can be affected by this error code change. We
checked a few. As of current upstream code, crosvm doesn't check for any
particular errno code when using kvm_(get|set)_one_reg(). Neither does
QEMU. rust-vmm doesn't have kvm-riscv support yet. Thus we have a good
chance of changing these error codes now while the KVM RISC-V ecosystem
is still new, minimizing user impact.
Change all get_one_reg() and set_one_reg() implementations to return
-ENOENT at all "no such register" cases.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
KVM userspaces need to be aware of the host SATP to allow them to
advertise it back to the guest OS.
Since this information is used to build the guest FDT we can't wait for
the SATP reg to be readable. We just need to read the SATP mode, thus
we can use the existing 'satp_mode' global that represents the SATP reg
with MODE set and both ASID and PPN cleared. E.g. for a 32 bit host
running with sv32 satp_mode is 0x80000000, for a 64 bit host running
sv57 satp_mode is 0xa000000000000000, and so on.
Add a new userspace virtual config register 'satp_mode' to allow
userspace to read the current SATP mode the host is using with
GET_ONE_REG API before spinning the vcpu.
'satp_mode' can't be changed via KVM, so SET_ONE_REG is allowed as long
as userspace writes the existing 'satp_mode'.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Let us sort isa extensions alphabetically in kvm_isa_ext_arr[] and
kvm_riscv_vcpu_isa_disable_allowed() so that future insertions are
more predictable.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
We extend the KVM ISA extension ONE_REG interface to allow KVM
user space to detect and enable Zicntr, Zicsr, Zifencei, and Zihpm
extensions for Guest/VM.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
We extend the KVM ISA extension ONE_REG interface to allow KVM
user space to detect and enable Zba and Zbs extensions for Guest/VM.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Currently, the ISA extension ONE_REG interface only allows enabling or
disabling one extension at a time. To improve this, we extend the ISA
extension ONE_REG interface (similar to SBI extension ONE_REG interface)
so that KVM user space can enable/disable multiple extensions in one
ioctl.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The VCPU ONE_REG interface has grown over time and it will continue
to grow with new ISA extensions and other features. Let us move all
ONE_REG related code to its own source file so that vcpu.c only
focuses only on high-level VCPU functions.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
* A pair of fixes for build-related failures in the selftests.
* A fix for a sparse warning in acpi_os_ioremap().
* A fix to restore the kernel PA offset in vmcoreinfo, to fix crash
handling.
-----BEGIN PGP SIGNATURE-----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=ImIa
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A pair of fixes for build-related failures in the selftests
- A fix for a sparse warning in acpi_os_ioremap()
- A fix to restore the kernel PA offset in vmcoreinfo, to fix crash
handling
* tag 'riscv-for-linus-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
Documentation: kdump: Add va_kernel_pa_offset for RISCV64
riscv: Export va_kernel_pa_offset in vmcoreinfo
RISC-V: ACPI: Fix acpi_os_ioremap to return iomem address
selftests: riscv: Fix compilation error with vstate_exec_nolibc.c
selftests/riscv: fix potential build failure during the "emit_tests" step
So that we do not end up mapping the whole linear mapping using 4K
pages, which is slow at boot time, and also very likely at runtime.
So make sure we align the start of DRAM on a PMD boundary.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reported-by: Song Shuai <suagrfillet@gmail.com>
Fixes: 3335068f87 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")
Tested-by: Song Shuai <suagrfillet@gmail.com>
Link: https://lore.kernel.org/r/20230704121837.248976-1-alexghiti@rivosinc.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Petr Tesarik <petrtesarik@huaweicloud.com> says:
From: Petr Tesarik <petr.tesarik.ext@huawei.com>
The kexec_file_load(2) syscall does not work at least in some kernel
builds. For details see the relevant section in this blog post:
https://sigillatum.tesarici.cz/2023-07-21-state-of-riscv64-kdump.html
This patch series handles an additional relocation types, removes the need
to implement a Global Offset Table (GOT) for the purgatory and fixes the
placement of initrd.
* b4-shazam-merge:
riscv/kexec: load initrd high in available memory
riscv/kexec: handle R_RISCV_CALL_PLT relocation type
Link: https://lore.kernel.org/r/cover.1690365011.git.petr.tesarik.ext@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
When initrd is loaded low, the secondary kernel fails like this:
INITRD: 0xdc581000+0x00eef000 overlaps in-use memory region
This initrd load address corresponds to the _end symbol, but the
reservation is aligned on PMD_SIZE, as explained by a comment in
setup_bootmem().
It is technically possible to align the initrd load address accordingly,
leaving a hole between the end of kernel and the initrd, but it is much
simpler to allocate the initrd top-down.
Fixes: 838b3e2848 ("RISC-V: Load purgatory in kexec_file")
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Cc: stable@vger.kernel.org
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/all/67c8eb9eea25717c2c8208d9bfbfaa39e6e2a1c6.1690365011.git.petr.tesarik.ext@huawei.com/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
R_RISCV_CALL has been deprecated and replaced by R_RISCV_CALL_PLT. See Enum
18-19 in Table 3. Relocation types here:
https://github.com/riscv-non-isa/riscv-elf-psabi-doc/blob/master/riscv-elf.adoc
It was deprecated in ("Deprecated R_RISCV_CALL, prefer R_RISCV_CALL_PLT"):
a0dced8501
Recent tools (at least GNU binutils-2.40) already use R_RISCV_CALL_PLT.
Kernels built with such binutils fail kexec_load_file(2) with:
kexec_image: Unknown rela relocation: 19
kexec_image: Error loading purgatory ret=-8
The binary code at the call site remains the same, so tell
arch_kexec_apply_relocations_add() to handle _PLT alike.
Fixes: 838b3e2848 ("RISC-V: Load purgatory in kexec_file")
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Cc: Li Zhengyu <lizhengyu3@huawei.com>
Cc: stable@vger.kernel.org
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/all/b046b164af8efd33bbdb7d4003273bdf9196a5b0.1690365011.git.petr.tesarik.ext@huawei.com/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRdM/uy1Ege0+EN1fNar9k/UBDW4wUCZMvevwAKCRBar9k/UBDW
42Z0AP90hLZ9OmoghYAlALHLl8zqXuHCV8OeFXR5auqG+kkcCwEAx6h99vnh4zgP
Tngj6Yid60o39/IZXXblhV37HfSiyQ8=
=/kVE
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2023-08-03
We've added 54 non-merge commits during the last 10 day(s) which contain
a total of 84 files changed, 4026 insertions(+), 562 deletions(-).
The main changes are:
1) Add SO_REUSEPORT support for TC bpf_sk_assign from Lorenz Bauer,
Daniel Borkmann
2) Support new insns from cpu v4 from Yonghong Song
3) Non-atomically allocate freelist during prefill from YiFei Zhu
4) Support defragmenting IPv(4|6) packets in BPF from Daniel Xu
5) Add tracepoint to xdp attaching failure from Leon Hwang
6) struct netdev_rx_queue and xdp.h reshuffling to reduce
rebuild time from Jakub Kicinski
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (54 commits)
net: invert the netdevice.h vs xdp.h dependency
net: move struct netdev_rx_queue out of netdevice.h
eth: add missing xdp.h includes in drivers
selftests/bpf: Add testcase for xdp attaching failure tracepoint
bpf, xdp: Add tracepoint to xdp attaching failure
selftests/bpf: fix static assert compilation issue for test_cls_*.c
bpf: fix bpf_probe_read_kernel prototype mismatch
riscv, bpf: Adapt bpf trampoline to optimized riscv ftrace framework
libbpf: fix typos in Makefile
tracing: bpf: use struct trace_entry in struct syscall_tp_t
bpf, devmap: Remove unused dtab field from bpf_dtab_netdev
bpf, cpumap: Remove unused cmap field from bpf_cpu_map_entry
netfilter: bpf: Only define get_proto_defrag_hook() if necessary
bpf: Fix an array-index-out-of-bounds issue in disasm.c
net: remove duplicate INDIRECT_CALLABLE_DECLARE of udp[6]_ehashfn
docs/bpf: Fix malformed documentation
bpf: selftests: Add defrag selftests
bpf: selftests: Support custom type and proto for client sockets
bpf: selftests: Support not connecting client socket
netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link
...
====================
Link: https://lore.kernel.org/r/20230803174845.825419-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 6724a76cff ("riscv: ftrace: Reduce the detour code size to
half") optimizes the detour code size of kernel functions to half with
T0 register and the upcoming DYNAMIC_FTRACE_WITH_DIRECT_CALLS of riscv
is based on this optimization, we need to adapt riscv bpf trampoline
based on this. One thing to do is to reduce detour code size of bpf
programs, and the second is to deal with the return address after the
execution of bpf trampoline. Meanwhile, we need to construct the frame
of parent function, otherwise we will miss one layer when unwinding.
The related tests have passed.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20230721100627.2630326-1-pulehui@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Since RISC-V Linux v6.4, the commit 3335068f87 ("riscv: Use
PUD/P4D/PGD pages for the linear mapping") changes phys_ram_base
from the physical start of the kernel to the actual start of the DRAM.
The Crash-utility's VTOP() still uses phys_ram_base and kernel_map.virt_addr
to translate kernel virtual address, that failed the Crash with Linux v6.4 [1].
Export kernel_map.va_kernel_pa_offset in vmcoreinfo to help Crash translate
the kernel virtual address correctly.
Fixes: 3335068f87 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")
Link: https://lore.kernel.org/linux-riscv/20230724040649.220279-1-suagrfillet@gmail.com/ [1]
Signed-off-by: Song Shuai <suagrfillet@gmail.com>
Reviewed-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230724100917.309061-1-suagrfillet@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
acpi_os_ioremap() currently is a wrapper to memremap() on
RISC-V. But the callers of acpi_os_ioremap() expect it to
return __iomem address and hence sparse tool reports a new
warning. Fix this issue by type casting to __iomem type.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307230357.egcTAefj-lkp@intel.com/
Fixes: a91a9ffbd3 ("RISC-V: Add support to build the ACPI core")
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230724100346.1302937-1-sunilvl@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
In the usage of ALTERNATIVE, "always" is misspelled as "alwyas".
Signed-off-by: Yuan Tan <tanyuan@tinylab.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230723165155.4896-1-tanyuan@tinylab.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
This patch adds declaration of the general purpose ADC for D1
and T113s SoCs.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-5-bigunclemax@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Commit a2225d931f ("autofs: remove left-over autofs4 stubs")
promised the removal of the fs/autofs/Kconfig fragment for AUTOFS4_FS
within a couple of releases, but five years later this still has not
happened yet, and AUTOFS4_FS is still enabled in 63 defconfigs.
Get rid of it mechanically:
git grep -l CONFIG_AUTOFS4_FS -- '*defconfig' |
xargs sed -i 's/AUTOFS4_FS/AUTOFS_FS/'
Also just remove the AUTOFS4_FS config option stub. Anybody who hasn't
regenerated their config file in the last five years will need to just
get the new name right when they do.
Signed-off-by: Sven Joachim <svenjoac@gmx.de>
Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Allwinner D1, T113 provide two CAN controllers that are variants
of the R40 controller.
I have tested support for these controllers on two boards:
- A Lichee Panel RV 86 Panel running a D1 chip
- A Mango Pi MQ Dual running a T113-s3 chip
Both of these fully support both CAN controllers.
Signed-off-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/all/20230721221552.1973203-4-contact@jookia.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the tdm controller node and pins configuration of tdm for the
StarFive JH7110 SoC.
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Walker Chen <walker.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add USB and PCIe PHY dts nodes for the StarFive JH7110 SoC.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Conor Dooley <conor.dooley@microchip.com> says:
Based on my latest iteration of deprecating riscv,isa [1], here's an
implementation of the new properties for Linux. The first few patches,
up to "RISC-V: split riscv_fill_hwcap() in 3", are all prep work that
further tames some of the extension related code, on top of my already
applied series that cleans up the ISA string parser.
Perhaps "RISC-V: shunt isa_ext_arr to cpufeature.c" is a bit gratuitous,
but I figured a bit of coalescing of extension related data structures
would be a good idea. Note that riscv,isa will still be used in the
absence of the new properties. Palmer suggested adding a Kconfig option
to turn off the fallback for DT, which I have gone and done. It's locked
behind the NONPORTABLE option for good reason.
* b4-shazam-merge:
RISC-V: provide Kconfig & commandline options to control parsing "riscv,isa"
RISC-V: try new extension properties in of_early_processor_hartid()
RISC-V: enable extension detection from dedicated properties
RISC-V: split riscv_fill_hwcap() in 3
RISC-V: add single letter extensions to riscv_isa_ext
RISC-V: add missing single letter extension definitions
RISC-V: repurpose riscv_isa_ext array in riscv_fill_hwcap()
RISC-V: shunt isa_ext_arr to cpufeature.c
RISC-V: drop a needless check in print_isa_ext()
RISC-V: don't parse dt/acpi isa string to get rv32/rv64
RISC-V: Provide a more helpful error message on invalid ISA strings
Link: https://lore.kernel.org/r/20230713-target-much-8ac624e90df8@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
As it says on the tin, provide Kconfig option to control parsing the
"riscv,isa" devicetree property. If either option is used, the kernel
will fall back to parsing "riscv,isa", where "riscv,isa-base" and
"riscv,isa-extensions" are not present.
The Kconfig options are set up so that the default kernel configuration
will enable the fallback path, without needing the commandline option.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Suggested-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-aviator-plausibly-a35662485c2c@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
To fully deprecate the kernel's use of "riscv,isa",
of_early_processor_hartid() needs to first try using the new properties,
before falling back to "riscv,isa".
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-tablet-jimmy-987fea0eb2e1@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add support for parsing the new riscv,isa-extensions property in
riscv_fill_hwcap(), by means of a new "property" member of the
riscv_isa_ext_data struct. For now, this shadows the name of the
extension for all users, however this may not be the case for all
extensions, based on how the dt-binding is written.
For the sake of backwards compatibility, fall back to the old scheme
if the new properties are not detected. For now, just inform, rather
than warn, when that happens.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-vocation-profane-39a74b3c2649@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Before adding more complexity to it, split riscv_fill_hwcap() into 3
distinct sections:
- riscv_fill_hwcap() still is the top level function, into which the
additional complexity will be added.
- riscv_fill_hwcap_from_isa_string() handles getting the information
from the riscv,isa/ACPI equivalent across harts & the various quirks
there
- riscv_parse_isa_string() does what it says on the tin.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-daylight-puritan-37aeb41a4d9b@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
So that riscv_fill_hwcap() can use riscv_isa_ext to probe for single
letter extensions, add them to it.
As a result, what gets spat out in /proc/cpuinfo will become borked, as
single letter extensions will be printed as part of the base extensions
and while printing from riscv_isa_arr. Take the opportunity to unify the
printing of the isa string, using the new member of riscv_isa_ext_data
in the process.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-despite-bright-de00ac888cc7@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
To facilitate adding single letter extensions to riscv_isa_ext, add
definitions for the extensions present in base_riscv_exts that do not
already have them.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-train-feisty-93de38250f98@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
In riscv_fill_hwcap() riscv_isa_ext array can be looped over, rather
than duplicating the list of extensions with individual
SET_ISA_EXT_MAP() usage. While at it, drop the statement-of-the-obvious
comments from the struct, rename uprop to something more suitable for
its new use & constify the members.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-dastardly-affiliate-4cf819dccde2@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
To facilitate using one struct to define extensions, rather than having
several, shunt isa_ext_arr to cpufeature.c, where it will be used for
probing extension presence also.
As that scope of the array as widened, prefix it with riscv & drop the
type from the variable name.
Since the new array is const, print_isa() needs a wee bit of cleanup to
avoid complaints about losing the const qualifier.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-spirits-upside-a2c61c65fd5a@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
isa_ext_arr cannot be empty, as some of the extensions within it are
always built into the kernel. When this code was first added, back in
commit a9b202606c ("RISC-V: Improve /proc/cpuinfo output for ISA
extensions"), the array was empty and needed a dummy item & thus there
could be no extensions present. When the first multi-letter ones did
get added, it was Sscofpmf - which didn't have a Kconfig symbol to
disable it.
Remove this check, as it has been redundant since Sscofpmf was added.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-veggie-mug-3d3bf6787ae2@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
When filling hwcap the kernel already expects the isa string to start with
rv32 if CONFIG_32BIT and rv64 if CONFIG_64BIT.
So when recreating the runtime isa-string we can also just go the other way
to get the correct starting point for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Evan Green <evan@rivosinc.com>
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230713-masculine-saddlebag-67a94966b091@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
dtbs_check w/ W=1 complains:
Warning (unit_address_vs_reg): /soc/ethernet@11c20000/ethernet-phy@7: node has a unit name, but no reg or ranges property
Warning (avoid_unnecessary_addr_size): /soc/ethernet@11c20000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
The ethernet@11c20000 node is guarded by an `#if (!SW_ET0_EN_N)` in
rzg2ul-smarc-som.dtsi, where the phy child node is added. In
rzfive-smarc-som.dtsi, the ethernet node is marked disabled & the
interrupt properties are deleted from the phy child node. As a result,
the produced dts looks like:
ethernet@11c20000 {
compatible = "renesas,r9a07g043-gbeth",
"renesas,rzg2l-gbeth";
/* snip */
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
ethernet-phy@7 {
};
};
Adding a corresponding `#if (!SW_ET0_EN_N)` around the node in
rzfive-smarc-som.dtsi avoids the complaint, as the empty child node is
not added:
ethernet@11c20000 {
compatible = "renesas,r9a07g043-gbeth",
"renesas,rzg2l-gbeth";
/* snip */
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230712-squealer-walmart-9587342ddec1@wendy
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add temperature sensor and thermal-zones support for
the StarFive JH7110 SoC. CPUFreq cooling is supported
in thermal-zones.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add temperature sensor and thermal-zones support for
the StarFive JH7100 SoC.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
v1.3B:
v1.3B uses motorcomm YT8531(rgmii-id phy) x2, need delay and
inverse configurations.
The tx_clk of v1.3B uses an external clock and needs to be
switched to an external clock source.
v1.2A:
v1.2A gmac0 uses motorcomm YT8531(rgmii-id) PHY, and needs delay
configurations.
v1.2A gmac1 uses motorcomm YT8512(rmii) PHY, and needs to
switch rx and rx to external clock sources.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
[conor: squashed a fix from Samin to use the actual properties]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* A fix for a formatting error in the hwprobe documentation.
* A fix for a spurious warning in the RISC-V PMU driver.
* A fix for memory detection on rv32, which does not manifest on any
known system.
* A fix to avoid parsing legacy parsing of I in ACPI ISA strings.
-----BEGIN PGP SIGNATURE-----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=8UWu
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- fix a formatting error in the hwprobe documentation
- fix a spurious warning in the RISC-V PMU driver
- fix memory detection on rv32 (problem does not manifest on any known
system)
- avoid parsing legacy parsing of I in ACPI ISA strings
* tag 'riscv-for-linus-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Don't include Zicsr or Zifencei in I from ACPI
riscv: mm: fix truncation warning on RV32
perf: RISC-V: Remove PERF_HES_STOPPED flag checking in riscv_pmu_start()
Documentation: RISC-V: hwprobe: Fix a formatting error
ACPI ISA strings are based on a specification after Zicsr and Zifencei
were split out of I, so we shouldn't be treating them as part of I. We
haven't release an ACPI-based kernel yet, so we don't need to worry
about compatibility with the old ISA strings.
Fixes: 07edc32779 ("RISC-V: always report presence of extensions formerly part of the base ISA")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20230711224600.10879-1-palmer@rivosinc.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the '-@' DTC option for the starfive devices. This option
populates the '__symbols__' node that contains all the necessary symbols
for supporting device-tree overlays (for instance from the firmware or
the bootloader) on these devices.
The starfive devices allow various modules to be connected and this
enables users to create out-of-tree device-tree overlays for these modules.
Please note that this change does increase the size of the resulting DTB
by ~20%. For example, with v6.4 increase in size is as follows:
jh7100-beaglev-starlight.dtb 6192 -> 7339
jh7100-starfive-visionfive-v1.dtb 6281 -> 7428
jh7110-starfive-visionfive-2-v1.2a.dtb 11101 -> 13447
jh7110-starfive-visionfive-2-v1.3b.dtb 11101 -> 13447
Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
lkp reports below sparse warning when building for RV32:
arch/riscv/mm/init.c:1204:48: sparse: warning: cast truncates bits from
constant value (100000000 becomes 0)
IMO, the reason we didn't see this truncates bug in real world is "0"
means MEMBLOCK_ALLOC_ACCESSIBLE in memblock and there's no RV32 HW
with more than 4GB memory.
Fix it anyway to make sparse happy.
Fixes: decf89f86e ("riscv: try to allocate crashkern region from 32bit addressible memory")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306080034.SLiCiOMn-lkp@intel.com/
Link: https://lore.kernel.org/r/20230709171036.1906-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The x86 Shadow stack feature includes a new type of memory called shadow
stack. This shadow stack memory has some unusual properties, which requires
some core mm changes to function properly.
One of these unusual properties is that shadow stack memory is writable,
but only in limited ways. These limits are applied via a specific PTE
bit combination. Nevertheless, the memory is writable, and core mm code
will need to apply the writable permissions in the typical paths that
call pte_mkwrite(). The goal is to make pte_mkwrite() take a VMA, so
that the x86 implementation of it can know whether to create regular
writable or shadow stack mappings.
But there are a couple of challenges to this. Modifying the signatures of
each arch pte_mkwrite() implementation would be error prone because some
are generated with macros and would need to be re-implemented. Also, some
pte_mkwrite() callers operate on kernel memory without a VMA.
So this can be done in a three step process. First pte_mkwrite() can be
renamed to pte_mkwrite_novma() in each arch, with a generic pte_mkwrite()
added that just calls pte_mkwrite_novma(). Next callers without a VMA can
be moved to pte_mkwrite_novma(). And lastly, pte_mkwrite() and all callers
can be changed to take/pass a VMA.
Start the process by renaming pte_mkwrite() to pte_mkwrite_novma() and
adding the pte_mkwrite() wrapper in linux/pgtable.h. Apply the same
pattern for pmd_mkwrite(). Since not all archs have a pmd_mkwrite_novma(),
create a new arch config HAS_HUGE_PAGE that can be used to tell if
pmd_mkwrite() should be defined. Otherwise in the !HAS_HUGE_PAGE cases the
compiler would not be able to find pmd_mkwrite_novma().
No functional change.
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/lkml/CAHk-=wiZjSu7c9sFYZb3q04108stgHff2wfbokGCCgW7riz+8Q@mail.gmail.com/
Link: https://lore.kernel.org/all/20230613001108.3040476-2-rick.p.edgecombe%40intel.com
The real-time signals enlarged the sigset_t type, and most architectures
have changed to using rt_sigreturn as the only way. The riscv is one of
them, and there is no sys_sigreturn in it. Only some old architecture
preserved sys_sigreturn as part of the historical burden.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230628091213.2908149-1-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
In order to generate the prologue and epilogue, the BPF JIT needs to
know which registers that are clobbered. Therefore, the during
pre-final passes, the prologue is generated after the body of the
program body-prologue-epilogue. Then, in the final pass, a proper
prologue-body-epilogue JITted image is generated.
This scheme has worked most of the time. However, for some large
programs with many jumps, e.g. the test_kmod.sh BPF selftest with
hardening enabled (blinding constants), this has shown to be
incorrect. For the final pass, when the proper prologue-body-epilogue
is generated, the image has not converged. This will lead to that the
final image will have incorrect jump offsets. The following is an
excerpt from an incorrect image:
| ...
| 3b8: 00c50663 beq a0,a2,3c4 <.text+0x3c4>
| 3bc: 0020e317 auipc t1,0x20e
| 3c0: 49630067 jalr zero,1174(t1) # 20e852 <.text+0x20e852>
| ...
| 20e84c: 8796 c.mv a5,t0
| 20e84e: 6422 c.ldsp s0,8(sp) # Epilogue start
| 20e850: 6141 c.addi16sp sp,16
| 20e852: 853e c.mv a0,a5 # Incorrect jump target
| 20e854: 8082 c.jr ra
The image has shrunk, and the epilogue offset is incorrect in the
final pass.
Correct the problem by always generating proper prologue-body-epilogue
outputs, which means that the first pass will only generate the body
to track what registers that are touched.
Fixes: 2353ecc6f9 ("bpf, riscv: add BPF JIT for RV64G")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230710074131.19596-1-bjorn@kernel.org
* A bunch of fixes/cleanups from the first part of the merge window,
mostly related to ACPI and vector as those were large.
* Some documentation improvements, mostly related to the new code.
* The "riscv,isa" DT key is deprecated.
* Support for link-time dead code elimination.
* Support for minor fault registration in userfaultd.
* A handful of cleanups around CMO alternatives.
-----BEGIN PGP SIGNATURE-----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=jBYf
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.5-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- A bunch of fixes/cleanups from the first part of the merge window,
mostly related to ACPI and vector as those were large
- Some documentation improvements, mostly related to the new code
- The "riscv,isa" DT key is deprecated
- Support for link-time dead code elimination
- Support for minor fault registration in userfaultd
- A handful of cleanups around CMO alternatives
* tag 'riscv-for-linus-6.5-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (23 commits)
riscv: mm: mark noncoherent_supported as __ro_after_init
riscv: mm: mark CBO relate initialization funcs as __init
riscv: errata: thead: only set cbom size & noncoherent during boot
riscv: Select HAVE_ARCH_USERFAULTFD_MINOR
RISC-V: Document the ISA string parsing rules for ACPI
risc-v: Fix order of IPI enablement vs RCU startup
mm: riscv: fix an unsafe pte read in huge_pte_alloc()
dt-bindings: riscv: deprecate riscv,isa
RISC-V: drop error print from riscv_hartid_to_cpuid()
riscv: Discard vector state on syscalls
riscv: move memblock_allow_resize() after linear mapping is ready
riscv: Enable ARCH_SUSPEND_POSSIBLE for s2idle
riscv: vdso: include vdso/vsyscall.h for vdso_data
selftests: Test RISC-V Vector's first-use handler
riscv: vector: clear V-reg in the first-use trap
riscv: vector: only enable interrupts in the first-use trap
RISC-V: Fix up some vector state related build failures
RISC-V: Document that V registers are clobbered on syscalls
riscv: disable HAVE_LD_DEAD_CODE_DATA_ELIMINATION for LLD
riscv: enable HAVE_LD_DEAD_CODE_DATA_ELIMINATION
...
These cleanups came up as part of the discussion on the "riscv: Reduce
ARCH_KMALLOC_MINALIGN to 8" patch set, but that needs additional work
and thus will be delayed at least a cycle.
* b4-shazam-merge:
riscv: mm: mark noncoherent_supported as __ro_after_init
riscv: mm: mark CBO relate initialization funcs as __init
riscv: errata: thead: only set cbom size & noncoherent during boot
Link: https://lore.kernel.org/linux-riscv/20230526165958.908-1-jszhang@kernel.org/
Link: https://lore.kernel.org/r/20230614165504.532-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The noncoherent_supported indicates whether the HW is coherent or not,
it won't change after booting, mark it as __ro_after_init.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230614165504.532-4-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The two functions cbo_get_block_size() and riscv_init_cbo_blocksizes()
are only called during booting, mark them as __init.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230614165504.532-3-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The CBOM size and whether the HW is noncoherent is known and
determined during booting and won't change after that.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230614165504.532-2-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
This allocates the VM flag needed to support the userfaultfd minor fault
functionality. Because the flag bit is >= bit 32, it can only be enabled
for 64-bit kernels. See commit 7677f7fd8b ("userfaultfd: add minor
fault registration mode") for more information.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20230624060321.3401504-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
These are cleanups for architecture specific header files:
- the comments in include/linux/syscalls.h have gone out of sync
and are really pointless, so these get removed
- The asm/bitsperlong.h header no longer needs to be architecture
specific on modern compilers, so use a generic version for newer
architectures that use new enough userspace compilers
- A cleanup for virt_to_pfn/virt_to_bus to have proper type
checking, forcing the use of pointers
-----BEGIN PGP SIGNATURE-----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=S/he
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"These are cleanups for architecture specific header files:
- the comments in include/linux/syscalls.h have gone out of sync and
are really pointless, so these get removed
- The asm/bitsperlong.h header no longer needs to be architecture
specific on modern compilers, so use a generic version for newer
architectures that use new enough userspace compilers
- A cleanup for virt_to_pfn/virt_to_bus to have proper type checking,
forcing the use of pointers"
* tag 'asm-generic-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
syscalls: Remove file path comments from headers
tools arch: Remove uapi bitsperlong.h of hexagon and microblaze
asm-generic: Unify uapi bitsperlong.h for arm64, riscv and loongarch
m68k/mm: Make pfn accessors static inlines
arm64: memory: Make virt_to_pfn() a static inline
ARM: mm: Make virt_to_pfn() a static inline
asm-generic/page.h: Make pfn accessors static inlines
xen/netback: Pass (void *) to virt_to_page()
netfs: Pass a pointer to virt_to_page()
cifs: Pass a pointer to virt_to_page() in cifsglob
cifs: Pass a pointer to virt_to_page()
riscv: mm: init: Pass a pointer to virt_to_page()
ARC: init: Pass a pointer to virt_to_pfn() in init
m68k: Pass a pointer to virt_to_pfn() virt_to_page()
fs/proc/kcore.c: Pass a pointer to virt_addr_valid()
There are three small fixes that came up sincie the past week:
- an incorrect bit offset in ixp4xx bus driver
- a riscv randconfig regression in the thead platform I merged
- whitespace fixes for some dts files
-----BEGIN PGP SIGNATURE-----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=cc9Z
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"There are three small fixes that came up sincie the past week:
- an incorrect bit offset in ixp4xx bus driver
- a riscv randconfig regression in the thead platform I merged
- whitespace fixes for some dts files"
* tag 'soc-fixes-6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
bus: ixp4xx: fix IXP4XX_EXP_T1_MASK
ARM: dts: st: add missing space before {
RISC-V: make ARCH_THEAD preclude XIP_KERNEL
Randy reported build errors in linux-next where XIP_KERNEL was enabled.
ARCH_THEAD requires alternatives to support the non-standard ISA
extensions used by the THEAD cores, which are mutually exclusive with
XIP kernels. Clone the dependency list from the Allwinner entry, since
Allwinner's D1 uses T-Head cores with the same non-standard extensions.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/all/ab38f6af-cb68-a918-1a63-2e7c927a8ffc@infradead.org/
Fixes: da47ce0039 ("riscv: Add the T-HEAD SoC family Kconfig option")
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230628-left-attractor-94b7bd5fbb83@wendy
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conor reports that risc-v tries to enable IPIs before telling the
core code to enable RCU. With the introduction of the mapple tree
as a backing store for the irq descriptors, this results in
a very shouty boot sequence, as RCU is legitimately upset.
Restore some sanity by moving the risc_ipi_enable() call after
notify_cpu_starting(), which explicitly enables RCU on the calling
CPU.
Fixes: 832f15f426 ("RISC-V: Treat IPIs as normal Linux IRQs")
Reported-by: Conor Dooley <conor@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230703-dupe-frying-79ae2ccf94eb@spud
Cc: Anup Patel <apatel@ventanamicro.com>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230703183126.1567625-1-maz@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The WARN_ON_ONCE() statement in riscv's huge_pte_alloc() is susceptible
to false positives, because the pte is read twice at the C language
level, locklessly, within the same conditional statement. Depending on
compiler behavior, this can lead to generated machine code that actually
reads the pte just once, or twice. Reading twice will expose the code to
changing pte values and cause incorrect behavior.
In [1], similar code actually caused a kernel crash on 64-bit x86, when
using clang to build the kernel, but only after the conversion from *pte
reads, to ptep_get(pte). The latter uses READ_ONCE(), which forced a
double read of *pte.
Rather than waiting for the upcoming ptep_get() conversion, just convert
this part of the code now, but in a way that avoids the above problem:
take a single snapshot of the pte before using it in the WARN
conditional.
As expected, this preparatory step does not actually change the
generated code ("make mm/hugetlbpage.s"), on riscv64, when using a gcc
12.2 cross compiler.
[1] https://lore.kernel.org/20230630013203.1955064-1-jhubbard@nvidia.com
Suggested-by: James Houghton <jthoughton@google.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20230703190044.311730-1-jhubbard@nvidia.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
As of commit 2ac8743437 ("RISC-V: split early & late of_node to
hartid mapping") my CI complains about newly added pr_err() messages
during boot, for example:
[ 0.000000] Couldn't find cpu id for hartid [0]
[ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller
Before the split, riscv_of_processor_hartid() contained a check for
whether the cpu was "available", before calling riscv_hartid_to_cpuid(),
but after the split riscv_of_processor_hartid() can be called for cpus
that are disabled.
Most callers of riscv_hartid_to_cpuid() already report custom errors
where it falls, making this print superfluous in those case. In other
places, the print adds nothing - see riscv_intc_init() for example.
Fixes: 2ac8743437 ("RISC-V: split early & late of_node to hartid mapping")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230629-paternity-grafted-b901b76d04a0@wendy
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The RISC-V vector specification states:
Executing a system call causes all caller-saved vector registers
(v0-v31, vl, vtype) and vstart to become unspecified.
The vector registers are set to all 1s, vill is set (invalid), and the
vector status is set to Dirty.
That way we can prevent userspace from accidentally relying on the
stated save.
Rémi pointed out [1] that writing to the registers might be
superfluous, and setting vill is sufficient.
Link: https://lore.kernel.org/linux-riscv/12784326.9UPPK3MAeB@basile.remlab.net/ # [1]
Suggested-by: Darius Rad <darius@bluespec.com>
Suggested-by: Palmer Dabbelt <palmer@rivosinc.com>
Suggested-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20230629142228.1125715-1-bjorn@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
With this configuration opened, the basic platform-independent s2idle is
provided by the sole "s2idle" string in `/sys/power/mem_sleep`.
At the end of s2idle, harts will hit the `wfi` instruction or enter the
SUSPENDED state through the sbi_cpuidle driver. The interrupt of possible
wakeup devices will be kept to wake the system up.
And platform-specific sleep states can be provided by future ACPI and
SBI SUSP extension support.
Signed-off-by: Song Shuai <songshuaishuai@tinylab.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20230529101524.322076-1-songshuaishuai@tinylab.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add include of <vdso/vsyscall.h> to pull in the defition of vdso_data
to remove the following sparse warning:
arch/riscv/kernel/vdso.c:39:18: warning: symbol 'vdso_data' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20230616114357.159601-1-ben.dooks@codethink.co.uk
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
* Eager page splitting optimization for dirty logging, optionally
allowing for a VM to avoid the cost of hugepage splitting in the stage-2
fault path.
* Arm FF-A proxy for pKVM, allowing a pKVM host to safely interact with
services that live in the Secure world. pKVM intervenes on FF-A calls
to guarantee the host doesn't misuse memory donated to the hyp or a
pKVM guest.
* Support for running the split hypervisor with VHE enabled, known as
'hVHE' mode. This is extremely useful for testing the split
hypervisor on VHE-only systems, and paves the way for new use cases
that depend on having two TTBRs available at EL2.
* Generalized framework for configurable ID registers from userspace.
KVM/arm64 currently prevents arbitrary CPU feature set configuration
from userspace, but the intent is to relax this limitation and allow
userspace to select a feature set consistent with the CPU.
* Enable the use of Branch Target Identification (FEAT_BTI) in the
hypervisor.
* Use a separate set of pointer authentication keys for the hypervisor
when running in protected mode, as the host is untrusted at runtime.
* Ensure timer IRQs are consistently released in the init failure
paths.
* Avoid trapping CTR_EL0 on systems with Enhanced Virtualization Traps
(FEAT_EVT), as it is a register commonly read from userspace.
* Erratum workaround for the upcoming AmpereOne part, which has broken
hardware A/D state management.
RISC-V:
* Redirect AMO load/store misaligned traps to KVM guest
* Trap-n-emulate AIA in-kernel irqchip for KVM guest
* Svnapot support for KVM Guest
s390:
* New uvdevice secret API
* CMM selftest and fixes
* fix racy access to target CPU for diag 9c
x86:
* Fix missing/incorrect #GP checks on ENCLS
* Use standard mmu_notifier hooks for handling APIC access page
* Drop now unnecessary TR/TSS load after VM-Exit on AMD
* Print more descriptive information about the status of SEV and SEV-ES during
module load
* Add a test for splitting and reconstituting hugepages during and after
dirty logging
* Add support for CPU pinning in demand paging test
* Add support for AMD PerfMonV2, with a variety of cleanups and minor fixes
included along the way
* Add a "nx_huge_pages=never" option to effectively avoid creating NX hugepage
recovery threads (because nx_huge_pages=off can be toggled at runtime)
* Move handling of PAT out of MTRR code and dedup SVM+VMX code
* Fix output of PIC poll command emulation when there's an interrupt
* Add a maintainer's handbook to document KVM x86 processes, preferred coding
style, testing expectations, etc.
* Misc cleanups, fixes and comments
Generic:
* Miscellaneous bugfixes and cleanups
Selftests:
* Generate dependency files so that partial rebuilds work as expected
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmSgHrIUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroORcAf+KkBlXwQMf+Q0Hy6Mfe0OtkKmh0Ae
6HJ6dsuMfOHhWv5kgukh+qvuGUGzHq+gpVKmZg2yP3h3cLHOLUAYMCDm+rjXyjsk
F4DbnJLfxq43Pe9PHRKFxxSecRcRYCNox0GD5UYL4PLKcH0FyfQrV+HVBK+GI8L3
FDzUcyJkR12Lcj1qf++7fsbzfOshL0AJPmidQCoc6wkLJpUEr/nYUqlI1Kx3YNuQ
LKmxFHS4l4/O/px3GKNDrLWDbrVlwciGIa3GZLS52PZdW3mAqT+cqcPcYK6SW71P
m1vE80VbNELX5q3YSRoOXtedoZ3Pk97LEmz/xQAsJ/jri0Z5Syk0Ok0m/Q==
=AMXp
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM64:
- Eager page splitting optimization for dirty logging, optionally
allowing for a VM to avoid the cost of hugepage splitting in the
stage-2 fault path.
- Arm FF-A proxy for pKVM, allowing a pKVM host to safely interact
with services that live in the Secure world. pKVM intervenes on
FF-A calls to guarantee the host doesn't misuse memory donated to
the hyp or a pKVM guest.
- Support for running the split hypervisor with VHE enabled, known as
'hVHE' mode. This is extremely useful for testing the split
hypervisor on VHE-only systems, and paves the way for new use cases
that depend on having two TTBRs available at EL2.
- Generalized framework for configurable ID registers from userspace.
KVM/arm64 currently prevents arbitrary CPU feature set
configuration from userspace, but the intent is to relax this
limitation and allow userspace to select a feature set consistent
with the CPU.
- Enable the use of Branch Target Identification (FEAT_BTI) in the
hypervisor.
- Use a separate set of pointer authentication keys for the
hypervisor when running in protected mode, as the host is untrusted
at runtime.
- Ensure timer IRQs are consistently released in the init failure
paths.
- Avoid trapping CTR_EL0 on systems with Enhanced Virtualization
Traps (FEAT_EVT), as it is a register commonly read from userspace.
- Erratum workaround for the upcoming AmpereOne part, which has
broken hardware A/D state management.
RISC-V:
- Redirect AMO load/store misaligned traps to KVM guest
- Trap-n-emulate AIA in-kernel irqchip for KVM guest
- Svnapot support for KVM Guest
s390:
- New uvdevice secret API
- CMM selftest and fixes
- fix racy access to target CPU for diag 9c
x86:
- Fix missing/incorrect #GP checks on ENCLS
- Use standard mmu_notifier hooks for handling APIC access page
- Drop now unnecessary TR/TSS load after VM-Exit on AMD
- Print more descriptive information about the status of SEV and
SEV-ES during module load
- Add a test for splitting and reconstituting hugepages during and
after dirty logging
- Add support for CPU pinning in demand paging test
- Add support for AMD PerfMonV2, with a variety of cleanups and minor
fixes included along the way
- Add a "nx_huge_pages=never" option to effectively avoid creating NX
hugepage recovery threads (because nx_huge_pages=off can be toggled
at runtime)
- Move handling of PAT out of MTRR code and dedup SVM+VMX code
- Fix output of PIC poll command emulation when there's an interrupt
- Add a maintainer's handbook to document KVM x86 processes,
preferred coding style, testing expectations, etc.
- Misc cleanups, fixes and comments
Generic:
- Miscellaneous bugfixes and cleanups
Selftests:
- Generate dependency files so that partial rebuilds work as
expected"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (153 commits)
Documentation/process: Add a maintainer handbook for KVM x86
Documentation/process: Add a label for the tip tree handbook's coding style
KVM: arm64: Fix misuse of KVM_ARM_VCPU_POWER_OFF bit index
RISC-V: KVM: Remove unneeded semicolon
RISC-V: KVM: Allow Svnapot extension for Guest/VM
riscv: kvm: define vcpu_sbi_ext_pmu in header
RISC-V: KVM: Expose IMSIC registers as attributes of AIA irqchip
RISC-V: KVM: Add in-kernel virtualization of AIA IMSIC
RISC-V: KVM: Expose APLIC registers as attributes of AIA irqchip
RISC-V: KVM: Add in-kernel emulation of AIA APLIC
RISC-V: KVM: Implement device interface for AIA irqchip
RISC-V: KVM: Skeletal in-kernel AIA irqchip support
RISC-V: KVM: Set kvm_riscv_aia_nr_hgei to zero
RISC-V: KVM: Add APLIC related defines
RISC-V: KVM: Add IMSIC related defines
RISC-V: KVM: Implement guest external interrupt line management
KVM: x86: Remove PRIx* definitions as they are solely for user space
s390/uv: Update query for secret-UVCs
s390/uv: replace scnprintf with sysfs_emit
s390/uvdevice: Add 'Lock Secret Store' UVC
...
If there is no context switch happens after we enable V for a process,
then we return to user space with whatever left on the CPU's V registers
accessible to the process. The leaked data could belong to another
process's V-context saved from last context switch, impacting process's
confidentiality on the system.
To prevent this from happening, we clear V registers by restoring
zero'd V context after turining on V.
Fixes: cd05483724 ("riscv: Allocate user's vector context in the first-use trap")
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20230627015556.12329-2-andy.chiu@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The function irqentry_exit_to_user_mode() must be called with interrupt
disabled. The caller of do_trap_insn_illegal() also assumes running
without interrupts. So, we should turn off interrupts after
riscv_v_first_use_handler() returns.
Fixes: cd05483724 ("riscv: Allocate user's vector context in the first-use trap")
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20230625155416.18629-1-andy.chiu@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Jisheng Zhang <jszhang@kernel.org> says:
When trying to run linux with various opensource riscv core on
resource limited FPGA platforms, for example, those FPGAs with less
than 16MB SDRAM, I want to save mem as much as possible. One of the
major technologies is kernel size optimizations, I found that riscv
does not currently support HAVE_LD_DEAD_CODE_DATA_ELIMINATION, which
passes -fdata-sections, -ffunction-sections to CFLAGS and passes the
--gc-sections flag to the linker.
This not only benefits my case on FPGA but also benefits defconfigs.
Here are some notable improvements from enabling this with defconfigs:
nommu_k210_defconfig:
text data bss dec hex
1112009 410288 59837 1582134 182436 before
962838 376656 51285 1390779 1538bb after
rv32_defconfig:
text data bss dec hex
8804455 2816544 290577 11911576 b5c198 before
8692295 2779872 288977 11761144 b375f8 after
defconfig:
text data bss dec hex
9438267 3391332 485333 13314932 cb2b74 before
9285914 3350052 483349 13119315 c82f53 after
patch1 and patch2 are clean ups.
patch3 fixes a typo.
patch4 finally enable HAVE_LD_DEAD_CODE_DATA_ELIMINATION for riscv.
* b4-shazam-merge:
riscv: disable HAVE_LD_DEAD_CODE_DATA_ELIMINATION for LLD
riscv: enable HAVE_LD_DEAD_CODE_DATA_ELIMINATION
vmlinux.lds.h: use correct .init.data.* section name
riscv: vmlinux-xip.lds.S: remove .alternative section
riscv: move options to keep entries sorted
riscv: Fix orphan section warnings caused by kernel/pi
Link: https://lore.kernel.org/r/20230523165502.2592-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
I get a few build failures along the lines of
./arch/riscv/include/uapi/asm/sigcontext.h:19:36: error: field ‘v_state’ has incomplete type
19 | struct __riscv_v_ext_state v_state;
| ^~~~~~~
./arch/riscv/include/uapi/asm/sigcontext.h:32:49: error: field ‘sc_extdesc’ has incomplete type
32 | struct __riscv_extra_ext_header sc_extdesc;
The V structures in question are defined for !assembly, so let's just do
so for the others.
Fixes: 8ee0b41898 ("riscv: signal: Add sigcontext save/restore for vector")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230619172101.18692-1-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
- Add new feature to have function graph tracer record the return value.
Adds a new option: funcgraph-retval ; when set, will show the return
value of a function in the function graph tracer.
- Also add the option: funcgraph-retval-hex where if it is not set, and
the return value is an error code, then it will return the decimal of
the error code, otherwise it still reports the hex value.
- Add the file /sys/kernel/tracing/osnoise/per_cpu/cpu<cpu>/timerlat_fd
That when a application opens it, it becomes the task that the timer lat
tracer traces. The application can also read this file to find out how
it's being interrupted.
- Add the file /sys/kernel/tracing/available_filter_functions_addrs
that works just the same as available_filter_functions but also shows
the addresses of the functions like kallsyms, except that it gives the
address of where the fentry/mcount jump/nop is. This is used by BPF to
make it easier to attach BPF programs to ftrace hooks.
- Replace strlcpy with strscpy in the tracing boot code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZJy6ixQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qnzRAPsEI2YgjaJSHnuPoGRHbrNil6pq66wY
LYaLizGI4Jv9BwEAqdSdcYcMiWo1SFBAO8QxEDM++BX3zrRyVgW8ahaTNgs=
=TF0C
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing updates from Steven Rostedt:
- Add new feature to have function graph tracer record the return
value. Adds a new option: funcgraph-retval ; when set, will show the
return value of a function in the function graph tracer.
- Also add the option: funcgraph-retval-hex where if it is not set, and
the return value is an error code, then it will return the decimal of
the error code, otherwise it still reports the hex value.
- Add the file /sys/kernel/tracing/osnoise/per_cpu/cpu<cpu>/timerlat_fd
That when a application opens it, it becomes the task that the timer
lat tracer traces. The application can also read this file to find
out how it's being interrupted.
- Add the file /sys/kernel/tracing/available_filter_functions_addrs
that works just the same as available_filter_functions but also shows
the addresses of the functions like kallsyms, except that it gives
the address of where the fentry/mcount jump/nop is. This is used by
BPF to make it easier to attach BPF programs to ftrace hooks.
- Replace strlcpy with strscpy in the tracing boot code.
* tag 'trace-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix warnings when building htmldocs for function graph retval
riscv: ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
tracing/boot: Replace strlcpy with strscpy
tracing/timerlat: Add user-space interface
tracing/osnoise: Skip running osnoise if all instances are off
tracing/osnoise: Switch from PF_NO_SETAFFINITY to migrate_disable
ftrace: Show all functions with addresses in available_filter_functions_addrs
selftests/ftrace: Add funcgraph-retval test case
LoongArch: ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
x86/ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
arm64: ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
tracing: Add documentation for funcgraph-retval and funcgraph-retval-hex
function_graph: Support recording and printing the return value of function
fgraph: Add declaration of "struct fgraph_ret_regs"
* Support for ACPI.
* Various cleanups to the ISA string parsing, including making them
case-insensitive
* Support for the vector extension.
* Support for independent irq/softirq stacks.
* Our CPU DT binding now has "unevaluatedProperties: false"
-----BEGIN PGP SIGNATURE-----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=Fpq8
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.5-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for ACPI
- Various cleanups to the ISA string parsing, including making them
case-insensitive
- Support for the vector extension
- Support for independent irq/softirq stacks
- Our CPU DT binding now has "unevaluatedProperties: false"
* tag 'riscv-for-linus-6.5-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (78 commits)
riscv: hibernate: remove WARN_ON in save_processor_state
dt-bindings: riscv: cpus: switch to unevaluatedProperties: false
dt-bindings: riscv: cpus: add a ref the common cpu schema
riscv: stack: Add config of thread stack size
riscv: stack: Support HAVE_SOFTIRQ_ON_OWN_STACK
riscv: stack: Support HAVE_IRQ_EXIT_ON_IRQ_STACK
RISC-V: always report presence of extensions formerly part of the base ISA
dt-bindings: riscv: explicitly mention assumption of Zicntr & Zihpm support
RISC-V: remove decrement/increment dance in ISA string parser
RISC-V: rework comments in ISA string parser
RISC-V: validate riscv,isa at boot, not during ISA string parsing
RISC-V: split early & late of_node to hartid mapping
RISC-V: simplify register width check in ISA string parsing
perf: RISC-V: Limit the number of counters returned from SBI
riscv: replace deprecated scall with ecall
riscv: uprobes: Restore thread.bad_cause
riscv: mm: try VMA lock-based page fault handling first
riscv: mm: Pre-allocate PGD entries for vmalloc/modules area
RISC-V: hwprobe: Expose Zba, Zbb, and Zbs
RISC-V: Track ISA extensions per hart
...
The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for each
SoC vendor, following the same scheme that is used on arm64, mips and
riscv. This has been discussed for many years, but so far we never did
this as there was a plan to move the files out of the kernel entirely,
which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along
with their device drivers.
* The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the time.
* Amlogic C3 is a Cortex-A35 based smart IP camera chip
* Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
* Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
* Qualcomm SDX75 is the latest generation modem chip that is used
as a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
* Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the Xuantie
C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those included
there are 39 new board files, but only five more 32-bit this time, probably
a new low:
* Marantec Maveo board based on dhcor imx6ull module
* Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
* Epson Moverio BT-200 AR glasses based on TI OMAP4
* PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
* ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than
we had in the recent releases:
* Three boards based on NXP i.MX8: Emtop SoM & Baseboard,
NXP i.MX8MM EVKB board and i.MX8MP based Gateworks Venice
gw7905-2x device.
* NVIDIA IGX Orin and Jetson Orin Nano boards, both based on
tegra234
* Qualcomm gains support for 6 reference boards on various members
of their IPQ networking SoC series, as well as the Sony Xperia M4
Aqua phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board
on top of the various reference platforms for their new chips.
* Rockchips support for several newer boards: Indiedroid Nova (rk3588),
Edgeble Neural Compute Module 6B (rk3588), FriendlyARM NanoPi R2C
Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn Fastrhino R66S/R68S
(rk3568)
* TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex Verdin
family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
* continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
* support for devicetree overlays on at91, bcm283x
* significant additions to existing SoC support on mediatek, qualcomm,
ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST STM32MP1
As usual, a lot more detail is available in the individual merge
commits.
-----BEGIN PGP SIGNATURE-----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=X/KE
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
This modifies our user mode stack expansion code to always take the
mmap_lock for writing before modifying the VM layout.
It's actually something we always technically should have done, but
because we didn't strictly need it, we were being lazy ("opportunistic"
sounds so much better, doesn't it?) about things, and had this hack in
place where we would extend the stack vma in-place without doing the
proper locking.
And it worked fine. We just needed to change vm_start (or, in the case
of grow-up stacks, vm_end) and together with some special ad-hoc locking
using the anon_vma lock and the mm->page_table_lock, it all was fairly
straightforward.
That is, it was all fine until Ruihan Li pointed out that now that the
vma layout uses the maple tree code, we *really* don't just change
vm_start and vm_end any more, and the locking really is broken. Oops.
It's not actually all _that_ horrible to fix this once and for all, and
do proper locking, but it's a bit painful. We have basically three
different cases of stack expansion, and they all work just a bit
differently:
- the common and obvious case is the page fault handling. It's actually
fairly simple and straightforward, except for the fact that we have
something like 24 different versions of it, and you end up in a maze
of twisty little passages, all alike.
- the simplest case is the execve() code that creates a new stack.
There are no real locking concerns because it's all in a private new
VM that hasn't been exposed to anybody, but lockdep still can end up
unhappy if you get it wrong.
- and finally, we have GUP and page pinning, which shouldn't really be
expanding the stack in the first place, but in addition to execve()
we also use it for ptrace(). And debuggers do want to possibly access
memory under the stack pointer and thus need to be able to expand the
stack as a special case.
None of these cases are exactly complicated, but the page fault case in
particular is just repeated slightly differently many many times. And
ia64 in particular has a fairly complicated situation where you can have
both a regular grow-down stack _and_ a special grow-up stack for the
register backing store.
So to make this slightly more manageable, the bulk of this series is to
first create a helper function for the most common page fault case, and
convert all the straightforward architectures to it.
Thus the new 'lock_mm_and_find_vma()' helper function, which ends up
being used by x86, arm, powerpc, mips, riscv, alpha, arc, csky, hexagon,
loongarch, nios2, sh, sparc32, and xtensa. So we not only convert more
than half the architectures, we now have more shared code and avoid some
of those twisty little passages.
And largely due to this common helper function, the full diffstat of
this series ends up deleting more lines than it adds.
That still leaves eight architectures (ia64, m68k, microblaze, openrisc,
parisc, s390, sparc64 and um) that end up doing 'expand_stack()'
manually because they are doing something slightly different from the
normal pattern. Along with the couple of special cases in execve() and
GUP.
So there's a couple of patches that first create 'locked' helper
versions of the stack expansion functions, so that there's a obvious
path forward in the conversion. The execve() case is then actually
pretty simple, and is a nice cleanup from our old "grow-up stackls are
special, because at execve time even they grow down".
The #ifdef CONFIG_STACK_GROWSUP in that code just goes away, because
it's just more straightforward to write out the stack expansion there
manually, instead od having get_user_pages_remote() do it for us in some
situations but not others and have to worry about locking rules for GUP.
And the final step is then to just convert the remaining odd cases to a
new world order where 'expand_stack()' is called with the mmap_lock held
for reading, but where it might drop it and upgrade it to a write, only
to return with it held for reading (in the success case) or with it
completely dropped (in the failure case).
In the process, we remove all the stack expansion from GUP (where
dropping the lock wouldn't be ok without special rules anyway), and add
it in manually to __access_remote_vm() for ptrace().
Thanks to Adrian Glaubitz and Frank Scheiner who tested the ia64 cases.
Everything else here felt pretty straightforward, but the ia64 rules for
stack expansion are really quite odd and very different from everything
else. Also thanks to Vegard Nossum who caught me getting one of those
odd conditions entirely the wrong way around.
Anyway, I think I want to actually move all the stack expansion code to
a whole new file of its own, rather than have it split up between
mm/mmap.c and mm/memory.c, but since this will have to be backported to
the initial maple tree vma introduction anyway, I tried to keep the
patches _fairly_ minimal.
Also, while I don't think it's valid to expand the stack from GUP, the
final patch in here is a "warn if some crazy GUP user wants to try to
expand the stack" patch. That one will be reverted before the final
release, but it's left to catch any odd cases during the merge window
and release candidates.
Reported-by: Ruihan Li <lrh2000@pku.edu.cn>
* branch 'expand-stack':
gup: add warning if some caller would seem to want stack expansion
mm: always expand the stack with the mmap write lock held
execve: expand new process stack manually ahead of time
mm: make find_extend_vma() fail if write lock not held
powerpc/mm: convert coprocessor fault to lock_mm_and_find_vma()
mm/fault: convert remaining simple cases to lock_mm_and_find_vma()
arm/mm: Convert to using lock_mm_and_find_vma()
riscv/mm: Convert to using lock_mm_and_find_vma()
mips/mm: Convert to using lock_mm_and_find_vma()
powerpc/mm: Convert to using lock_mm_and_find_vma()
arm64/mm: Convert to using lock_mm_and_find_vma()
mm: make the page fault mmap locking killable
mm: introduce new 'lock_mm_and_find_vma()' page fault helper
top-level directories.
- Douglas Anderson has added a new "buddy" mode to the hardlockup
detector. It permits the detector to work on architectures which
cannot provide the required interrupts, by having CPUs periodically
perform checks on other CPUs.
- Zhen Lei has enhanced kexec's ability to support two crash regions.
- Petr Mladek has done a lot of cleanup on the hard lockup detector's
Kconfig entries.
- And the usual bunch of singleton patches in various places.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZJelTAAKCRDdBJ7gKXxA
juDkAP0VXWynzkXoojdS/8e/hhi+htedmQ3v2dLZD+vBrctLhAEA7rcH58zAVoWa
2ejqO6wDrRGUC7JQcO9VEjT0nv73UwU=
=F293
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-06-24-19-23' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-mm updates from Andrew Morton:
- Arnd Bergmann has fixed a bunch of -Wmissing-prototypes in top-level
directories
- Douglas Anderson has added a new "buddy" mode to the hardlockup
detector. It permits the detector to work on architectures which
cannot provide the required interrupts, by having CPUs periodically
perform checks on other CPUs
- Zhen Lei has enhanced kexec's ability to support two crash regions
- Petr Mladek has done a lot of cleanup on the hard lockup detector's
Kconfig entries
- And the usual bunch of singleton patches in various places
* tag 'mm-nonmm-stable-2023-06-24-19-23' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (72 commits)
kernel/time/posix-stubs.c: remove duplicated include
ocfs2: remove redundant assignment to variable bit_off
watchdog/hardlockup: fix typo in config HARDLOCKUP_DETECTOR_PREFER_BUDDY
powerpc: move arch_trigger_cpumask_backtrace from nmi.h to irq.h
devres: show which resource was invalid in __devm_ioremap_resource()
watchdog/hardlockup: define HARDLOCKUP_DETECTOR_ARCH
watchdog/sparc64: define HARDLOCKUP_DETECTOR_SPARC64
watchdog/hardlockup: make HAVE_NMI_WATCHDOG sparc64-specific
watchdog/hardlockup: declare arch_touch_nmi_watchdog() only in linux/nmi.h
watchdog/hardlockup: make the config checks more straightforward
watchdog/hardlockup: sort hardlockup detector related config values a logical way
watchdog/hardlockup: move SMP barriers from common code to buddy code
watchdog/buddy: simplify the dependency for HARDLOCKUP_DETECTOR_PREFER_BUDDY
watchdog/buddy: don't copy the cpumask in watchdog_next_cpu()
watchdog/buddy: cleanup how watchdog_buddy_check_hardlockup() is called
watchdog/hardlockup: remove softlockup comment in touch_nmi_watchdog()
watchdog/hardlockup: in watchdog_hardlockup_check() use cpumask_copy()
watchdog/hardlockup: don't use raw_cpu_ptr() in watchdog_hardlockup_kick()
watchdog/hardlockup: HAVE_NMI_WATCHDOG must implement watchdog_hardlockup_probe()
watchdog/hardlockup: keep kernel.nmi_watchdog sysctl as 0444 if probe fails
...
- Yosry has also eliminated cgroup's atomic rstat flushing.
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability.
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning.
- Lorenzo Stoakes has done some maintanance work on the get_user_pages()
interface.
- Liam Howlett continues with cleanups and maintenance work to the maple
tree code. Peng Zhang also does some work on maple tree.
- Johannes Weiner has done some cleanup work on the compaction code.
- David Hildenbrand has contributed additional selftests for
get_user_pages().
- Thomas Gleixner has contributed some maintenance and optimization work
for the vmalloc code.
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code.
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting.
- Christoph Hellwig has some cleanups for the filemap/directio code.
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the provided
APIs rather than open-coding accesses.
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings.
- John Hubbard has a series of fixes to the MM selftesting code.
- ZhangPeng continues the folio conversion campaign.
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock.
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment from
128 to 8.
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management.
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code.
- Vishal Moola also has done some folio conversion work.
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZJejewAKCRDdBJ7gKXxA
joggAPwKMfT9lvDBEUnJagY7dbDPky1cSYZdJKxxM2cApGa42gEA6Cl8HRAWqSOh
J0qXCzqaaN8+BuEyLGDVPaXur9KirwY=
=B7yQ
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
- Yosry Ahmed brought back some cgroup v1 stats in OOM logs
- Yosry has also eliminated cgroup's atomic rstat flushing
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning
- Lorenzo Stoakes has done some maintanance work on the
get_user_pages() interface
- Liam Howlett continues with cleanups and maintenance work to the
maple tree code. Peng Zhang also does some work on maple tree
- Johannes Weiner has done some cleanup work on the compaction code
- David Hildenbrand has contributed additional selftests for
get_user_pages()
- Thomas Gleixner has contributed some maintenance and optimization
work for the vmalloc code
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting
- Christoph Hellwig has some cleanups for the filemap/directio code
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the
provided APIs rather than open-coding accesses
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings
- John Hubbard has a series of fixes to the MM selftesting code
- ZhangPeng continues the folio conversion campaign
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment
from 128 to 8
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code
- Vishal Moola also has done some folio conversion work
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch
* tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (380 commits)
mm/hugetlb: remove hugetlb_set_page_subpool()
mm: nommu: correct the range of mmap_sem_read_lock in task_mem()
hugetlb: revert use of page_cache_next_miss()
Revert "page cache: fix page_cache_next/prev_miss off by one"
mm/vmscan: fix root proactive reclaim unthrottling unbalanced node
mm: memcg: rename and document global_reclaim()
mm: kill [add|del]_page_to_lru_list()
mm: compaction: convert to use a folio in isolate_migratepages_block()
mm: zswap: fix double invalidate with exclusive loads
mm: remove unnecessary pagevec includes
mm: remove references to pagevec
mm: rename invalidate_mapping_pagevec to mapping_try_invalidate
mm: remove struct pagevec
net: convert sunrpc from pagevec to folio_batch
i915: convert i915_gpu_error to use a folio_batch
pagevec: rename fbatch_count()
mm: remove check_move_unevictable_pages()
drm: convert drm_gem_put_pages() to use a folio_batch
i915: convert shmem_sg_free_table() to use a folio_batch
scatterlist: add sg_set_folio()
...
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAmSbftQWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJj0MD/9X9jzJzCmsAU+yNldeoAzC84Sk
GVU3RBxGcTNysL1gZXynkIgigw7DWc4htMGeSABHHwQRVP65JCH1Kw/VqIkyumbx
9LdX6IklMJb4pRT4PVU3azebV4eNmSjlur2UxMeW54Czm91/6I8RHbJOyAPnOUmo
2oomGdP/hpEHtKR7hgy8Axc6w5ySwQixh2V5sVZG3VbvCS5WKTmTXbs6puuRT5hz
iHt7v+7VtEg/Qf1W7J2oxfoghvVBsaRrSLrExWT/oZYh1ZxM7DsCAAoG/IsDgHGA
9LBXiRECgAFThbHVxLvvKZQMXdVk0i8iXLX43XMKC0wTA+NTyH7wlcQQ4RWNMuo8
sfA9Qm9gMArXaf64aymr3Uwn20Zan0391HdlbhOJZAE6v3PPJbleUnM58AzD2d3r
5Lz6AIFBxDImy+3f9iDWgacCT5/PkeiXTHzk9QnKhJyKKtRA58XJxj4q2+rPnGJP
n4haXqoxD5FJbxdXiGKk31RS0U5HBug7wkOcUrTqDHUbc/QNU2b7dxTKUx+zYtCU
uV5emPzpF4H4z+91WpO47n9gkMAfwV0lt9S2dwS8pxsgqctbmIan+Jgip7rsqZ2G
OgLXBsb43eEs+6WgO8tVt/ZHYj9ivGMdrcNcsIfikzNs/xweUJ53k2xSEn2xEa5J
cwANDmkL6QQK7yfeeg==
=s0j1
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"There are three areas of note:
A bunch of strlcpy()->strscpy() conversions ended up living in my tree
since they were either Acked by maintainers for me to carry, or got
ignored for multiple weeks (and were trivial changes).
The compiler option '-fstrict-flex-arrays=3' has been enabled
globally, and has been in -next for the entire devel cycle. This
changes compiler diagnostics (though mainly just -Warray-bounds which
is disabled) and potential UBSAN_BOUNDS and FORTIFY _warning_
coverage. In other words, there are no new restrictions, just
potentially new warnings. Any new FORTIFY warnings we've seen have
been fixed (usually in their respective subsystem trees). For more
details, see commit df8fc4e934.
The under-development compiler attribute __counted_by has been added
so that we can start annotating flexible array members with their
associated structure member that tracks the count of flexible array
elements at run-time. It is possible (likely?) that the exact syntax
of the attribute will change before it is finalized, but GCC and Clang
are working together to sort it out. Any changes can be made to the
macro while we continue to add annotations.
As an example of that last case, I have a treewide commit waiting with
such annotations found via Coccinelle:
https://git.kernel.org/linus/adc5b3cb48a049563dc673f348eab7b6beba8a9b
Also see commit dd06e72e68 for more details.
Summary:
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex
arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members"
* tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (54 commits)
netfilter: ipset: Replace strlcpy with strscpy
uml: Replace strlcpy with strscpy
um: Use HOST_DIR for mrproper
kallsyms: Replace all non-returning strlcpy with strscpy
sh: Replace all non-returning strlcpy with strscpy
of/flattree: Replace all non-returning strlcpy with strscpy
sparc64: Replace all non-returning strlcpy with strscpy
Hexagon: Replace all non-returning strlcpy with strscpy
kobject: Use return value of strreplace()
lib/string_helpers: Change returned value of the strreplace()
jbd2: Avoid printing outside the boundary of the buffer
checkpatch: Check for 0-length and 1-element arrays
riscv/purgatory: Do not use fortified string functions
s390/purgatory: Do not use fortified string functions
x86/purgatory: Do not use fortified string functions
acpi: Replace struct acpi_table_slit 1-element array with flex-array
clocksource: Replace all non-returning strlcpy with strscpy
string: use __builtin_memcpy() in strlcpy/strlcat
staging: most: Replace all non-returning strlcpy with strscpy
drm/i2c: tda998x: Replace all non-returning strlcpy with strscpy
...
- Introduce cmpxchg128() -- aka. the demise of cmpxchg_double().
The cmpxchg128() family of functions is basically & functionally
the same as cmpxchg_double(), but with a saner interface: instead
of a 6-parameter horror that forced u128 - u64/u64-halves layout
details on the interface and exposed users to complexity,
fragility & bugs, use a natural 3-parameter interface with u128 types.
- Restructure the generated atomic headers, and add
kerneldoc comments for all of the generic atomic{,64,_long}_t
operations. Generated definitions are much cleaner now,
and come with documentation.
- Implement lock_set_cmp_fn() on lockdep, for defining an ordering
when taking multiple locks of the same type. This gets rid of
one use of lockdep_set_novalidate_class() in the bcache code.
- Fix raw_cpu_generic_try_cmpxchg() bug due to an unintended
variable shadowing generating garbage code on Clang on certain
ARM builds.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=DsYj
-----END PGP SIGNATURE-----
Merge tag 'locking-core-2023-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
- Introduce cmpxchg128() -- aka. the demise of cmpxchg_double()
The cmpxchg128() family of functions is basically & functionally the
same as cmpxchg_double(), but with a saner interface.
Instead of a 6-parameter horror that forced u128 - u64/u64-halves
layout details on the interface and exposed users to complexity,
fragility & bugs, use a natural 3-parameter interface with u128
types.
- Restructure the generated atomic headers, and add kerneldoc comments
for all of the generic atomic{,64,_long}_t operations.
The generated definitions are much cleaner now, and come with
documentation.
- Implement lock_set_cmp_fn() on lockdep, for defining an ordering when
taking multiple locks of the same type.
This gets rid of one use of lockdep_set_novalidate_class() in the
bcache code.
- Fix raw_cpu_generic_try_cmpxchg() bug due to an unintended variable
shadowing generating garbage code on Clang on certain ARM builds.
* tag 'locking-core-2023-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (43 commits)
locking/atomic: scripts: fix ${atomic}_dec_if_positive() kerneldoc
percpu: Fix self-assignment of __old in raw_cpu_generic_try_cmpxchg()
locking/atomic: treewide: delete arch_atomic_*() kerneldoc
locking/atomic: docs: Add atomic operations to the driver basic API documentation
locking/atomic: scripts: generate kerneldoc comments
docs: scripts: kernel-doc: accept bitwise negation like ~@var
locking/atomic: scripts: simplify raw_atomic*() definitions
locking/atomic: scripts: simplify raw_atomic_long*() definitions
locking/atomic: scripts: split pfx/name/sfx/order
locking/atomic: scripts: restructure fallback ifdeffery
locking/atomic: scripts: build raw_atomic_long*() directly
locking/atomic: treewide: use raw_atomic*_<op>()
locking/atomic: scripts: add trivial raw_atomic*_<op>()
locking/atomic: scripts: factor out order template generation
locking/atomic: scripts: remove leftover "${mult}"
locking/atomic: scripts: remove bogus order parameter
locking/atomic: xtensa: add preprocessor symbols
locking/atomic: x86: add preprocessor symbols
locking/atomic: sparc: add preprocessor symbols
locking/atomic: sh: add preprocessor symbols
...
- Parallel CPU bringup
The reason why people are interested in parallel bringup is to shorten
the (kexec) reboot time of cloud servers to reduce the downtime of the
VM tenants.
The current fully serialized bringup does the following per AP:
1) Prepare callbacks (allocate, intialize, create threads)
2) Kick the AP alive (e.g. INIT/SIPI on x86)
3) Wait for the AP to report alive state
4) Let the AP continue through the atomic bringup
5) Let the AP run the threaded bringup to full online state
There are two significant delays:
#3 The time for an AP to report alive state in start_secondary() on
x86 has been measured in the range between 350us and 3.5ms
depending on vendor and CPU type, BIOS microcode size etc.
#4 The atomic bringup does the microcode update. This has been
measured to take up to ~8ms on the primary threads depending on
the microcode patch size to apply.
On a two socket SKL server with 56 cores (112 threads) the boot CPU
spends on current mainline about 800ms busy waiting for the APs to come
up and apply microcode. That's more than 80% of the actual onlining
procedure.
This can be reduced significantly by splitting the bringup mechanism
into two parts:
1) Run the prepare callbacks and kick the AP alive for each AP which
needs to be brought up.
The APs wake up, do their firmware initialization and run the low
level kernel startup code including microcode loading in parallel
up to the first synchronization point. (#1 and #2 above)
2) Run the rest of the bringup code strictly serialized per CPU
(#3 - #5 above) as it's done today.
Parallelizing that stage of the CPU bringup might be possible in
theory, but it's questionable whether required surgery would be
justified for a pretty small gain.
If the system is large enough the first AP is already waiting at the
first synchronization point when the boot CPU finished the wake-up of
the last AP. That reduces the AP bringup time on that SKL from ~800ms
to ~80ms, i.e. by a factor ~10x.
The actual gain varies wildly depending on the system, CPU, microcode
patch size and other factors. There are some opportunities to reduce
the overhead further, but that needs some deep surgery in the x86 CPU
bringup code.
For now this is only enabled on x86, but the core functionality
obviously works for all SMP capable architectures.
- Enhancements for SMP function call tracing so it is possible to locate
the scheduling and the actual execution points. That allows to measure
IPI delivery time precisely.
-----BEGIN PGP SIGNATURE-----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=Y8if
-----END PGP SIGNATURE-----
Merge tag 'smp-core-2023-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP updates from Thomas Gleixner:
"A large update for SMP management:
- Parallel CPU bringup
The reason why people are interested in parallel bringup is to
shorten the (kexec) reboot time of cloud servers to reduce the
downtime of the VM tenants.
The current fully serialized bringup does the following per AP:
1) Prepare callbacks (allocate, intialize, create threads)
2) Kick the AP alive (e.g. INIT/SIPI on x86)
3) Wait for the AP to report alive state
4) Let the AP continue through the atomic bringup
5) Let the AP run the threaded bringup to full online state
There are two significant delays:
#3 The time for an AP to report alive state in start_secondary()
on x86 has been measured in the range between 350us and 3.5ms
depending on vendor and CPU type, BIOS microcode size etc.
#4 The atomic bringup does the microcode update. This has been
measured to take up to ~8ms on the primary threads depending
on the microcode patch size to apply.
On a two socket SKL server with 56 cores (112 threads) the boot CPU
spends on current mainline about 800ms busy waiting for the APs to
come up and apply microcode. That's more than 80% of the actual
onlining procedure.
This can be reduced significantly by splitting the bringup
mechanism into two parts:
1) Run the prepare callbacks and kick the AP alive for each AP
which needs to be brought up.
The APs wake up, do their firmware initialization and run the
low level kernel startup code including microcode loading in
parallel up to the first synchronization point. (#1 and #2
above)
2) Run the rest of the bringup code strictly serialized per CPU
(#3 - #5 above) as it's done today.
Parallelizing that stage of the CPU bringup might be possible
in theory, but it's questionable whether required surgery
would be justified for a pretty small gain.
If the system is large enough the first AP is already waiting at
the first synchronization point when the boot CPU finished the
wake-up of the last AP. That reduces the AP bringup time on that
SKL from ~800ms to ~80ms, i.e. by a factor ~10x.
The actual gain varies wildly depending on the system, CPU,
microcode patch size and other factors. There are some
opportunities to reduce the overhead further, but that needs some
deep surgery in the x86 CPU bringup code.
For now this is only enabled on x86, but the core functionality
obviously works for all SMP capable architectures.
- Enhancements for SMP function call tracing so it is possible to
locate the scheduling and the actual execution points. That allows
to measure IPI delivery time precisely"
* tag 'smp-core-2023-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
trace,smp: Add tracepoints for scheduling remotelly called functions
trace,smp: Add tracepoints around remotelly called functions
MAINTAINERS: Add CPU HOTPLUG entry
x86/smpboot: Fix the parallel bringup decision
x86/realmode: Make stack lock work in trampoline_compat()
x86/smp: Initialize cpu_primary_thread_mask late
cpu/hotplug: Fix off by one in cpuhp_bringup_mask()
x86/apic: Fix use of X{,2}APIC_ENABLE in asm with older binutils
x86/smpboot/64: Implement arch_cpuhp_init_parallel_bringup() and enable it
x86/smpboot: Support parallel startup of secondary CPUs
x86/smpboot: Implement a bit spinlock to protect the realmode stack
x86/apic: Save the APIC virtual base address
cpu/hotplug: Allow "parallel" bringup up to CPUHP_BP_KICK_AP_STATE
x86/apic: Provide cpu_primary_thread mask
x86/smpboot: Enable split CPU startup
cpu/hotplug: Provide a split up CPUHP_BRINGUP mechanism
cpu/hotplug: Reset task stack state in _cpu_up()
cpu/hotplug: Remove unused state functions
riscv: Switch to hotplug core state synchronization
parisc: Switch to hotplug core state synchronization
...
Linking allyesconfig with ld.lld-17 with CONFIG_DEAD_CODE_ELIMINATION=y
takes hours. Assuming this is a performance regression that can be
fixed, tentatively disable this for now so that allyesconfig builds
don't start timing out. If and when there's a fix to ld.lld, this can
be converted to a version check instead so that users of older but still
supported versions of ld.lld don't hurt themselves by enabling
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y.
Link: https://github.com/ClangBuiltLinux/linux/issues/1881
Link: https://lore.kernel.org/linux-riscv/ZJXTwqZIkXLxXaSi@google.com/
Reported-by: Palmer Dabbelt <palmer@dabbelt.com>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Select CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION for RISC-V, allowing
the user to enable dead code elimination. In order for this to work,
ensure that we keep the alternative table by annotating them with KEEP.
This boots well on qemu with both rv32_defconfig & rv64 defconfig, but
it only shrinks their builds by ~1%, a smaller config is thereforce
customized to test this feature:
| rv32 | rv64
--------|------------------------|---------------------
No DCE | 4460684 | 4893488
DCE | 3986716 | 4376400
Shrink | 473968 (~10.6%) | 517088 (~10.5%)
The config used above only reserves necessary options to boot on qemu
with serial console, more like the size-critical embedded scenes:
- rv64 config: https://pastebin.com/crz82T0s
- rv32 config: rv64 config + 32-bit.config
Here is Jisheng's original commit-msg:
When trying to run linux with various opensource riscv core on
resource limited FPGA platforms, for example, those FPGAs with less
than 16MB SDRAM, I want to save mem as much as possible. One of the
major technologies is kernel size optimizations, I found that riscv
does not currently support HAVE_LD_DEAD_CODE_DATA_ELIMINATION, which
passes -fdata-sections, -ffunction-sections to CFLAGS and passes the
--gc-sections flag to the linker.
This not only benefits my case on FPGA but also benefits defconfigs.
Here are some notable improvements from enabling this with defconfigs:
nommu_k210_defconfig:
text data bss dec hex
1112009 410288 59837 1582134 182436 before
962838 376656 51285 1390779 1538bb after
rv32_defconfig:
text data bss dec hex
8804455 2816544 290577 11911576 b5c198 before
8692295 2779872 288977 11761144 b375f8 after
defconfig:
text data bss dec hex
9438267 3391332 485333 13314932 cb2b74 before
9285914 3350052 483349 13119315 c82f53 after
Signed-off-by: Zhangjin Wu <falcon@tinylab.org>
Co-developed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
Tested-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com> # build
Link: https://lore.kernel.org/r/20230523165502.2592-5-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
ALTERNATIVE mechanism can't work on XIP, and this is also reflected by
below Kconfig dependency:
RISCV_ALTERNATIVE
...
depends on !XIP_KERNEL
...
So there's no .alternative section at all for XIP case, remove it.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com> # build
Link: https://lore.kernel.org/r/20230523165502.2592-3-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
During hibernation or restoration, freeze_secondary_cpus
checks num_online_cpus via BUG_ON, and the subsequent
save_processor_state also does the checking with WARN_ON.
In the case of CONFIG_PM_SLEEP_SMP=n, freeze_secondary_cpus
is not defined, but the sole possible condition to disable
CONFIG_PM_SLEEP_SMP is !SMP where num_online_cpus is always 1.
We also don't have to check it in save_processor_state.
So remove the unnecessary checking in save_processor_state.
Fixes: c031721001 ("RISC-V: Add arch functions to support hibernation/suspend-to-disk")
Signed-off-by: Song Shuai <songshuaishuai@tinylab.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230609075049.2651723-4-songshuaishuai@tinylab.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
guoren@kernel.org <guoren@kernel.org> says:
From: Guo Ren <guoren@linux.alibaba.com>
This patch series adds independent irq/softirq stacks to decrease the
press of the thread stack. Also, add a thread STACK_SIZE config for
users to adjust the proper size during compile time.
* b4-shazam-merge:
riscv: stack: Add config of thread stack size
riscv: stack: Support HAVE_SOFTIRQ_ON_OWN_STACK
riscv: stack: Support HAVE_IRQ_EXIT_ON_IRQ_STACK
Link: https://lore.kernel.org/r/20230614013018.2168426-1-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Conor Dooley <conor@kernel.org> says:
From: Conor Dooley <conor.dooley@microchip.com>
Here are some bits that were discussed with Drew on the "should we
allow caps" threads that I have now created patches for:
- splitting of riscv_of_processor_hartid() into two distinct functions,
one for use purely during early boot, prior to the establishment of
the possible-cpus mask & another to fit the other current use-cases
- that then allows us to then completely skip some validation of the
hartid in the parser
- the biggest diff in the series is a rework of the comments in the
parser, as I have mostly found the existing (sparse) ones to not be
all that helpful whenever I have to go back and look at it
- from writing the comments, I found a conditional doing a bit of a
dance that I found counter-intuitive, so I've had a go at making that
match what I would expect a little better
- `i` implies 4 other extensions, so add them as extensions and set
them for the craic. Sure why not like...
* b4-shazam-merge:
RISC-V: always report presence of extensions formerly part of the base ISA
dt-bindings: riscv: explicitly mention assumption of Zicntr & Zihpm support
RISC-V: remove decrement/increment dance in ISA string parser
RISC-V: rework comments in ISA string parser
RISC-V: validate riscv,isa at boot, not during ISA string parsing
RISC-V: split early & late of_node to hartid mapping
RISC-V: simplify register width check in ISA string parsing
Link: https://lore.kernel.org/r/20230607-audacity-overhaul-82bb867a825f@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The commit 0cac21b02b ("riscv: use 16KB kernel stack on 64-bit")
increases the thread size mandatory, but some scenarios, such as D1 with
a small memory footprint, would suffer from that. After independent irq
stack support, let's give users a choice to determine their custom stack
size.
Link: https://lore.kernel.org/linux-riscv/5f6e6c39-b846-4392-b468-02202404de28@www.fastmail.com/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230614013018.2168426-4-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the HAVE_SOFTIRQ_ON_OWN_STACK feature for the IRQ_STACKS config, and
the irq and softirq use the same irq_stack of percpu.
Tested-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230614013018.2168426-3-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Now we specify the minimal version of GCC as 5.1 and Clang/LLVM as 11.0.0
in Documentation/process/changes.rst, __CHAR_BIT__ and __SIZEOF_LONG__ are
usable, it is probably fine to unify the definition of __BITS_PER_LONG as
(__CHAR_BIT__ * __SIZEOF_LONG__) in asm-generic uapi bitsperlong.h.
In order to keep safe and avoid regression, only unify uapi bitsperlong.h
for some archs such as arm64, riscv and loongarch which are using newer
toolchains that have the definitions of __CHAR_BIT__ and __SIZEOF_LONG__.
Suggested-by: Xi Ruoyao <xry111@xry111.site>
Link: https://lore.kernel.org/all/d3e255e4746de44c9903c4433616d44ffcf18d1b.camel@xry111.site/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arch/a3a4f48a-07d4-4ed9-bc53-5d383428bdd2@app.fastmail.com/
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The previous patch ("function_graph: Support recording and printing
the return value of function") has laid the groundwork for the for
the funcgraph-retval, and this modification makes it available on
the RISC-V platform.
We introduce a new structure called fgraph_ret_regs for the RISC-V
platform to hold return registers and the frame pointer. We then
fill its content in the return_to_handler and pass its address to
the function ftrace_return_to_handler to record the return value.
Link: https://lore.kernel.org/linux-trace-kernel/a8d71b12259f90e7e63d0ea654fcac95b0232bbc.1680954589.git.pengdonglin@sangfor.com.cn
Signed-off-by: Donglin Peng <pengdonglin@sangfor.com.cn>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Of these four extensions, two were part of the base ISA when the port was
written and are required by the kernel. The other two are implied when
`i` is in riscv,isa on DT systems.
There's not much that userspace can do with this extra information, but
there is no harm in reporting an ISA string that closer resembles the
current versions of the specifications either.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230607-nest-collision-5796b6be8be6@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
While expanding on the comments in the ISA string parsing code, I
noticed that the conditional decrement of `isa` at the end of the loop
was a bit odd.
The parsing code expects that at the start of the for loop, `isa` will
point to the first character of the next unparsed extension.
However, depending on what the next extension is, this may not be true.
Unless the next extension is a multi-letter extension preceded by an
underscore, `isa` will either point to the string's null-terminator or
to the first character of the next extension, once the switch statement
has been evaluated.
Obviously incrementing `isa` at the end of the loop could cause it to
increment past the null terminator or miss a single letter extension, so
`isa` is conditionally decremented, just so that the loop can increment
it again.
It's easier to understand the code if, instead of this decrement +
increment dance, we instead use a while loop & rely on the handling of
individual extension types to leave `isa` pointing to the first
character of the next extension.
As already mentioned, this won't be the case where the following
extension is multi-letter & preceded by an underscore. To handle that,
invert the check and increment rather than decrement.
Hopefully this eliminates a "huh?!?" moment the next time somebody tries
to understand this code.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20230607-estate-left-f20faabefb89@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
I have found these comments to not be at all helpful whenever I look at
the parser. Further, the comments in the default case (single letter
parser) are not quite right either.
Group the comments into a larger one at the start of each case, that
attempts to explain things at a higher level.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230607-headpiece-tannery-83ed5cc4856a@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Since riscv_fill_hwcap() now only iterates over possible cpus, the
basic validation of whether riscv,isa contains "rv<width>" can be moved
to riscv_early_of_processor_hartid().
Further, "ima" support is required by the kernel, so reject any CPU not
fitting the bill.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20230607-guts-blurry-67e711acf328@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Some back and forth with Drew [1] about riscv_fill_hwcap() resulted in
the realisation that it is not very useful to parse the DT & perform
validation of riscv,isa every time we would like to get the id for a
hart.
Although it is no longer called in riscv_fill_hwcap(),
riscv_of_processor_hartid() is called in several other places.
Notably in setup_smp() it forms part of the logic for filling the mask
of possible CPUs. Since a possible CPU must have passed this basic
validation of riscv,isa, a repeat validation is not required.
Rename riscv_of_processor_id() to riscv_early_of_processor_id(),
which will be called from setup_smp() & introduce a new
riscv_of_processor_id() which makes use of the pre-populated mask of
possible cpus.
Link: https://lore.kernel.org/linux-riscv/xvdswl3iyikwvamny7ikrxo2ncuixshtg3f6uucjahpe3xpc5c@ud4cz4fkg5dj/ [1]
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20230607-glade-pastel-d8cbd9d9f3c6@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Saving off the `isa` pointer to a temp variable, followed by checking if
it has been incremented is a bit of an odd pattern. Perhaps it was done
to avoid a funky looking if statement mixed with the ifdeffery.
Now that we use IS_ENABLED() here just return from the parser as soon as
we detect a mismatch between the string and the currently running
kernel.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20230607-splatter-bacterium-a75bb9f0d0b7@spud
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZJDOAwAKCRB4tDGHoIJi
0gAoAQCqGDPqdw5MdT/+tTJqkAIVFo3KyxSrMHvv3TE36Xp1HgEAxJQ+NoZ30nhx
pbaJaRcZDw7PKOVmMJ92R564EMdjngA=
=hJMo
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=U5qO
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5 Part 2
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
dt-bindings: riscv: Add T-HEAD TH1520 board compatibles
dt-bindings: timer: Add T-HEAD TH1520 clint
dt-bindings: interrupt-controller: Add T-HEAD's TH1520 PLIC
Link: https://lore.kernel.org/r/20230620-fidelity-variety-60b47c889e31@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCZIdfVAAKCRB4tDGHoIJi
0mspAP4m1zrOWojsDmwpodCajBTW6PEtMAztxRUj/qeA4IEsYgEA+NI1DhrUkwZ6
K1vw1VzP56auVkdS3X7ZBhEpjfnkCg4=
=JA/v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=NR4f
-----END PGP SIGNATURE-----
Merge tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.5
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: Add cpu scaling for JH7110 SoC
riscv: dts: starfive: Enable axp15060 pmic for cpufreq
dt-bindings: interrupt-controller: sifive,plic: Sort compatible values
dt-bindings: timer: sifive,clint: Clean up compatible value section
riscv: dts: starfive: jh7110: Add watchdog node
riscv: dts: starfive: jh7100: Add watchdog node
riscv: dts: starfive: Add PMU controller node
MAINTAINERS: exclude maintained subdirs in RISC-V misc DT entry
Link: https://lore.kernel.org/r/20230612-fasting-floss-0bc05a08bc7a@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
scall is a deprecated alias for ecall. ecall is used in several places,
so there is no assembler compatibility concern.
Signed-off-by: Fangrui Song <maskray@google.com>
Link: https://lore.kernel.org/r/20230423223210.126948-1-maskray@google.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
thread.bad_cause is saved in arch_uprobe_pre_xol(), it should be restored
in arch_uprobe_{post,abort}_xol() accordingly, otherwise the save operation
is meaningless, this change is similar with x86 and powerpc.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Fixes: 74784081aa ("riscv: Add uprobes supported")
Link: https://lore.kernel.org/r/1682214146-3756-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Attempt VMA lock-based page fault handling first, and fall back to the
existing mmap_lock-based handling if that fails.
A simple running the ebizzy benchmark on Lichee Pi 4A shows that
PER_VMA_LOCK can improve the ebizzy benchmark by about 32.68%. In
theory, the more CPUs, the bigger improvement, but I don't have any
HW platform which has more than 4 CPUs.
This is the riscv variant of "x86/mm: try VMA lock-based page fault
handling first".
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Link: https://lore.kernel.org/r/20230523165942.2630-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
We extend the KVM ISA extension ONE_REG interface to allow KVM
user space to detect and enable Svnapot extension for Guest/VM.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The RISC-V port requires that kernel PGD entries are to be
synchronized between MMs. This is done via the vmalloc_fault()
function, that simply copies the PGD entries from init_mm to the
faulting one.
Historically, faulting in PGD entries have been a source for both bugs
[1], and poor performance.
One way to get rid of vmalloc faults is by pre-allocating the PGD
entries. Pre-allocating the entries potientially wastes 64 * 4K (65 on
SV39). The pre-allocation function is pulled from Jörg Rödel's x86
work, with the addition of 3-level page tables (PMD allocations).
The pmd_alloc() function needs the ptlock cache to be initialized
(when split page locks is enabled), so the pre-allocation is done in a
RISC-V specific pgtable_cache_init() implementation.
Pre-allocate the kernel PGD entries for the vmalloc/modules area, but
only for 64b platforms.
Link: https://lore.kernel.org/lkml/20200508144043.13893-1-joro@8bytes.org/ # [1]
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20230531093817.665799-1-bjorn@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
