The interrupt status bit of the previous error data transmition will
affect the next operation and cause continuous SPI transmission failure.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-7-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
the wakeup interrupt handler which is guaranteed not to run while
@resume noirq() is being executed. the patch can help to avoid the
wakeup source try to access spi when the spi is in suspend mode.
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-6-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After power up, the cs and clock is in default status, and the cs-high
and clock polarity dts property configuration will take no effect until
the calling of rockchip_spi_config in the first transmission.
So preset them to make sure a correct voltage before the first
transmission coming.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-5-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi which's version is higher than ver 2 will automatically
enable this feature.
If the length of master transmission is uncertain, the RK spi slave
is better to automatically stop after cs inactive instead of waiting
for xfer_completion forever.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-4-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After slave abort, all DMA should be stopped, or it will affect the
next transmission and maybe abort again.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously zero length transfers submitted to the Rokchip SPI driver would
time out in the SPI layer. This happens because the SPI peripheral does
not trigger a transfer completion interrupt for zero length transfers.
Fix that by completing zero length transfers immediately at start of
transfer.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20210827050357.165409-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix checkpatch errors:
ERROR: code indent should use tabs where possible
#484: FILE: spi-rockchip.c:484:
+^I | CR0_BHT_8BIT << CR0_BHT_OFFSET$
ERROR: code indent should use tabs where possible
#485: FILE: spi-rockchip.c:485:
+^I | CR0_SSD_ONE << CR0_SSD_OFFSET$
ERROR: code indent should use tabs where possible
#486: FILE: spi-rockchip.c:486:
+^I | CR0_EM_BIG << CR0_EM_OFFSET;$
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616566602-13894-11-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Building this file with clang leads to a an unreachable code path
causing a warning from objtool:
drivers/spi/spi-rockchip.o: warning: objtool: rockchip_spi_transfer_one()+0x2e0: sibling call from callable instruction with modified stack frame
Change the unreachable() into an error return that can be
handled if it ever happens, rather than silently crashing
the kernel.
Fixes: 65498c6ae2 ("spi: rockchip: support 4bit words")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210226140109.3477093-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If SPI is used for periodic polling any sensor, significant delays
sometimes appear. Switching on module clocks during resume lead to delays.
Enabling autosuspend mode causes the controller to not suspend between
SPI transfers and the delays disappear.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Link: https://lore.kernel.org/r/20201016085014.31667-1-al.kochet@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The RXFLR is possible larger than rx_left in Rockchip SPI, fix it.
Fixes: 01b59ce5da ("spi: rockchip: use irq rather than polling")
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO depth of SPI V2 is 64 instead of 32, add support for it.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-2-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The burst length can be adjusted according to the transmission
length to improve the transmission rate
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-1-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The original implementation set num_chipselect to ROCKCHIP_SPI_MAX_CS_NUM (2)
which seems wrong here. spi0 has 2 native cs, all others just one. With
enable and use of cs_gpiods / GPIO CS, its correct to set the num_chipselect
from the num-cs property and set max_native_cs with the define.
If num-cs is missing the default set to num_chipselect = 1.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-4-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for spi slave mode in spi-rockchip. The register map has an entry
for it. If spi-slave is set in dts, set this corresponding bit and add to
mode_bits the SPI_NO_CS, allow slave mode without explicit CS use.
Slave abort function had been added.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-3-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup, move from the compatibily layer struct spi_master over
to struct spi_controller, and rename the related function calls.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-2-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
The Rockchip spi binding is updated to yaml and new models
were added. The spi on px30,rk3308 and rk3328 are the same as
other Rockchip based SoCs, so add compatible string for it.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309151004.7780-1-jbx6244@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kthread.h can't be included in psi_types.h because it creates a circular
inclusion with kthread.h eventually including psi_types.h and
complaining on kthread structures not being defined because they are
defined further in the kthread.h. Resolve this by removing psi_types.h
inclusion from the headers included from kthread.h.
Link: http://lkml.kernel.org/r/20190319235619.260832-7-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes tx and bi-directional dma transfers on rk3399-gru-kevin.
It seems the SPI fifo must have room for 2 bursts when the dma_tx_req
signal is generated or it might skip some words. This in turn makes
the rx dma channel never complete for bi-directional transfers.
Fix it by setting tx burst length to fifo_len / 4 and the dma
watermark to fifo_len / 2.
However the rk3399 TRM says (sic):
"DMAC support incrementing-address burst and fixed-address burst. But in
the case of access SPI and UART at byte or halfword size, DMAC only
support fixed-address burst and the address must be aligned to word."
So this relies on fifo_len being a multiple of 16 such that the
burst length (= fifo_len / 4) is a multiple of 4 and the addresses
will be word-aligned.
Fixes: dcfc861d24 ("spi: rockchip: adjust dma watermark and burstlen")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing support for lsb-first mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware supports 4, 8 and 16bit spi words,
so add the missing support for 4bit words.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register an interrupt handler to fill/empty the
tx and rx fifos rather than busy-looping.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we no longer potentially change spi clock
at runtime we can precompute the rx sample delay
at probe time rather than for each transfer.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver previously checked each transfer if the
requested speed was higher than possible with the
current spi clock rate and raised the clock rate
accordingly.
However, there is no check to see if the spi clock
was actually set that high and no way to dynamically
lower the spi clock rate again.
So it seems any potiential users of this functionality
are better off just setting the spi clock rate at init
using the assigned-clock-rates devicetree property.
Removing this dynamic spi clock rate raising allows
us let the spi framework handle min/max speeds
for us.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to know if we're using dma when setting
up the transfer, so just use a local variable for
that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In almost all cases we already have a pointer to the
spi master structure where we have the driver data.
The only exceptions are the dma callbacks which are
easily fixed by passing them the master and using
spi_master_get_devdata to retrieve the driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi master (aka spi controller) structure already
has two fields for storing the rx and tx dma channels.
Just use them rather than duplicating them in driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just read transfer info directly from the spi device
and transfer structures rather than storing it in
driver data first.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Successful transfers leave the spi disabled, so if
we just make sure to disable the spi on error
there should be no need to disable the spi from
master->unprepare_message.
This also flushes the tx and rx fifos,
so no need to do that manually.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The state field is currently only used to make sure
only the last of the tx and rx dma callbacks issue
an spi_finalize_current_transfer.
Rather than using a spinlock we can get away
with just turning the state field into an atomic_t.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware supports 3 different variants of SPI
and there were some code around it, but nothing
to actually set it to anything but "Motorola SPI".
Just drop that code and always use that mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use C99 designated initializers for dma slave config
structures. This also makes sure uninitialized fields
are zeroed so we don't need an explicit memset.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_enable_chip function takes a boolean
argument. Change the type to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
CTRLR1 is number of data frames, when rx only.
When data frame is 8 bit, CTRLR1 is len-1.
When data frame is 16 bit, CTRLR1 is (len/2)-1.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
