Move iwl_isr_legacy function to iwl_legacy.c since it only used
by legacy devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 100 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 6000g2a series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 6000g2b series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debugfs code for ath5k was printing some unsigned int
stats with %d instead of %u. This meant that you could see
negative numbers instead of a clean wrap.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add watchdog functions for managing the Queues inside the hardware.
Normally the driver doesn't have much to do with these queues
directly, but the Ralink drivers did implement watchdog functions
for these. These watchdog functions are not triggered that often,
compared to the other watchdog functions, but I have at least
seen them trigger once or twice during a long stresstest run.
v2: Add extra documentation for register fields
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.
We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue_entry argument to rt2x00queue_kick_tx_queue,
doesn't make sense due to the function name (it is called
kick QUEUE)... But neither do we need the queue_entry, since
we need the data_queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue->lock is only used to protect the index
numbers. Rename the lock accordingly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb.c:43: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00queue.c:804: ERROR: space prohibited after that open parenthesis '('
rt2x00queue.c:805: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00link.c:70: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib.h:60: ERROR: space prohibited after that open parenthesis '('
rt2x00lib.h:60: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00dev.c:689: ERROR: spaces required around that '=' (ctx:WxV)
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00config.c:136: ERROR: space required before the open parenthesis '('
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800usb.h:43: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:43: ERROR: space prohibited before that close parenthesis ')'
rt2800usb.h:44: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:44: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800usb.c:48: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci.h:41: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:42: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:43: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:44: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:55: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:55: ERROR: space prohibited before that close parenthesis ')'
rt2800pci.h:56: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:56: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800lib.c:831: ERROR: inline keyword should sit between storage class and type
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800.h:1511: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1511: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1513: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1513: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1515: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1515: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1517: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1517: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1519: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1519: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1521: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1521: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1661: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1661: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1662: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1662: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1663: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2013: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2013: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2014: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2014: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb.c:42: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500pci.h:1091: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1091: ERROR: space prohibited before that close parenthesis ')'
rt2500pci.h:1092: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1092: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2400pci.h:812: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:812: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:813: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:813: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:950: ERROR: Macros with complex values should be enclosed in parenthesis
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a few shortcomings in the tx path.
* move temp. ampdu_[ack]_len out of txinfo->pad.
* fix WARN_ON from tx.c:line 300 when tx_ampdu_queue
fails to queue the frame.
* In tx_prepare, we already have a local pointer
to the station's ieee80211_sta struct.
* remove a second !sta check, tx_prepare already takes
care of that.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
crypto_free_cipher() is a wrapper around crypto_free_tfm() which is a
wrapper around crypto_destroy_tfm() and the latter can handle being passed
a NULL pointer, so checking for NULL in the
ieee80211_aes_key_free()/ieee80211_aes_cmac_key_free() wrappers around
crypto_free_cipher() is pointless and just increase object code size
needlesly and makes us execute extra test/branch instructions that we
don't need.
Btw; don't we have to many wrappers around wrappers ad nauseam here?
Anyway, this patch removes the redundant conditionals.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a few comments in rt73usb.h and rt61pci.h.
Signed-off-by: Lalith Suresh <suresh.lalith@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSSID register shouldn't be set in AP mode on some older devices (like
rt73usb) as it breaks hw crypto on these. However, rt2800 devices explicitly
need the BSSID register set to the same value as our own MAC address (only
in AP mode).
Hence, don't set the BSSID from rt2x00lib but move it down into rt2800 to
avoid problems on older devices.
This fixes a regression (at least for rt73usb) and avoids a new regression
for rt2800 devices in 2.6.36.
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Lee <lee-in-berlin@web.de>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By not scheduling the TX/RX completion worker threads
when Radio is disabled, or hardware has been unplugged,
the queues cannot be completely cleaned.
This causes crashes when the hardware has been unplugged while
the radio is still enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy driver uses 0xff as the second argument for the MCU_SLEEP
command. It is still unknown what the values actually mean, but
this will at least keep the command in-sync with the original
driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement a basic flush callback function, which simply loops
over all TX queues and waits until all frames have been transmitted
and the status reports have been gathered.
At this moment we don't support dropping any frames during the
flush, but mac80211 will only send 'false' for this argument anyway,
so this is not important at this time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the TX status handler failed to clear the queue
in rt2x00usb_watchdog_tx_dma() we shouldn't use a failsave
to use the rt2x00usb txdone handler.
If a driver has overriden the txdone handler it must make
sure the txdone handler is capable of cleaning up the queue itself.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename rt2x00queue_timeout to rt2x00queue_status_timeout to
better describe what is actually timing out (note that
we already have a rt2x00queue_dma_timeout).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rt2x00 is compiled with debugging but frame dumping is currently
not active we can avoid the call to do_gettimeofday. Furthermore,
frame dumping is not the default case, mark it as unlikely.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx descriptor values qid, cw_min, cw_max and aifs are directly
accessible through the tx entry struct. So there's no need to copy
them into the tx descriptor and passing them to the indiviual drivers.
Instead we can just get the correct value from the tx entry.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least some devices need such a long time to inititalize WPDMA. This
only increases the maximum wait time and shouldn't affect devices that
have been working before.
Reported-by: Joshua Smith <jesmith@kaon.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All rt2x00 devices used the same Tx and Rx ring size (24 entries) till
now. Newer devices (like rt2800) can however make use of a larger TX and
RX ring due to 11n capabilities (AMPDUs of size 64 for example).
Hence, bring rt2x00 in sync with the legacy drivers and use the same TX
and RX ring sizes. Also remove the global defines RX_ENTRIES, TX_ENTRIES,
BEACON_ENTRIES and ATIM_ENTRIES and use per driver values.
That is 24 entries for rt2400pci, 32 entries for rt2500pci, rt2500usb,
rt61pci and rt73usb and 128 (RX) and 64 (TX) for rt2800pci and rt2800usb.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the magic value initialisation of the TXOP_CTRL_CFG register by
defining its fields and using them during intialisation. The field
RESERVED_TRUN_EN is referred to as reserved, however it is set to 1 by
the legacy drivers. Hence, do the same.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current ath9k tx queue handling code showed a few issues that could
lead to locking issues, tx stalls due to stopped queues, and maybe even
DMA issues.
The main source of these issues is that in some places the queue is
selected via skb queue mapping in places where this mapping may no
longer be valid. One such place is when data frames are transmitted via
the CAB queue (for powersave buffered frames). This is made even worse
by a lookup WMM AC values from the assigned tx queue (which is
undefined for the CAB queue).
This messed up the pending frame counting, which in turn caused issues
with queues getting stopped, but not woken again.
To fix these issues, this patch removes an unnecessary abstraction
separating a driver internal queue number from the skb queue number
(not to be confused with the hardware queue number).
It seems that this abstraction may have been necessary because of tx
queue preinitialization from the initvals. This patch avoids breakage
here by pushing the software <-> hardware queue mapping to the function
that assigns the tx queues and redefining the WMM AC definitions to
match the numbers used by mac80211 (also affects ath9k_htc).
To ensure consistency wrt. pending frame count tracking, these counters
are moved to the ath_txq struct, updated with the txq lock held, but
only where the tx queue selected by the skb queue map actually matches
the tx queue used by the driver for the frame.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Mandriva patch seems to stem from 2.6.14, so much for their
upstreaming effort.
Didn't find another Linux reference of it, just an omnious
"USB\VID_1044&PID_8004" from GigabyteZD1201U.INF for
Gigabyte GN-WLBZ101 802.11b USB Adapter, which matches the
Mandriva patch comment.
Aboves file also lists an "USB\VID_1044&PID_8006", which I have
kept appart as this "Gigabyte GN-WBZB-M 802.11b USB Adapter"
didn't show up in googling.
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current 8187B initialization misses anaparam registers restore after
8187 reset. This causes ANAPARAM register to stay zeroed out (ANAPARAM2
kept its value on my tests). To avoid this, call rtl8187_set_anaparam
right after chip reset (to be on the safe side, as it makes sure we
restore all ANAPARAM registers).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually you set RTL818X_CONFIG3_ANAPARAM_WRITE when you are going to
change/write ANAPARAM registers. But in current initialization of
RTL8187B there is a place where ANAPARAM_WRITE bit is set without any
ANAPARAM register being written, without reason, so remove it.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are repeated calls for anaparam on/off sequence in the code.
Consolidate the common code in rtl8187_set_anaparam and use it where
needed.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The GNTSel bit should only concern pci devices by looking at RTL8180
spec, which is not the case of 8187B. Also testing shows that trying to
set this bit fails, a subsequent read from the register after trying to
set it shows that the bit isn't set, seems the hardware ignores it,
which makes sense. This setting was a left over from Realtek sources.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 8187B start, comment about pll reset, and move it out of ANAPARAM
write sequence, so that code is more readable.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The table with misc register initialization was setting it, and later
on we would set it again with a explicity call to rtl818x_iowrite16_idx.
Remove duplicate initialization from the register table.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were using wrong address for BRSR (Basic Rate Set Register) while
initializing its value, comparing with Realtek sources, for 8187B case.
Also, the same register is initialized in rtl8187b_reg_table, so remove
the duplicate initialization from the table.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 8187B path, we set a initial value for beacon interval and atim
window on initialization. But this isn't needed, since same setup is
done on rtl8187_config.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
