The vdd10_lcd and vcc18_lcd regulators need to be enabled for HDMI output
to work, so add 'regulator-always-on', just as is done in rk3288-firefly.dtsi.
Also enable i2c5, the hdmi block and configure the correc cec pin.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In order to be able to use more than 4GB of RAM when the LPAE is
activated, the dts must be converted in 64 bits.
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We deprecated the "num-slots" property now and plan to get
rid of it finally. Just move a step to cleanup it from DT.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use macros to describe gpios will make the dts easier to
read and write.
All the modifications done with sed:
sed -i -e 's/ 0 GPIO_ACTIVE_/ RK_PA0 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 1 GPIO_ACTIVE_/ RK_PA1 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 2 GPIO_ACTIVE_/ RK_PA2 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
.......
.......
sed -i -e 's/ 30 GPIO_ACTIVE_/ RK_PD6 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 31 GPIO_ACTIVE_/ RK_PD7 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
Tested with:
for i in dts-old/*dtb; do scripts/dtc/dtx_diff $i dts-new/$(basename $i); done
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[also adapted the gpio interrupts]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are many regulators are missed in previous commit, this
commit complete most of them. It also fix some mistakes in the
regulator properties. The VDD_10(REG10) and VCC_18(REG11) had better
to keep in always-on state, as it is used as the USB PHY supply,
corretly we have no way to assign power supply to a USB PHY.
The VCCA_33(REG8) should be enabled or the GMAC won't work.
It also fix the wrong properties for audio in io-domains, the supply
connected to APIO4_VDD is different to firefly release version.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Firefly RK3288 Reload is a combination Firefly rk3288 core board
with the Reload baseboard. Add a dtsi for the Firefly rk3288 core
which can be included into the dts for the various baseboards
in the future and dts for Reload base board.
Currently supported are serial console, wired networking, eMMC and
SD storage, SPFIF, IR receiver, LEDs, SDIO wifi and USB. But only
the OTG could work on the host mode now, the other USB host can't
work now, additional patches are required.
Signed-off-by: Randy Li <ayaka@soulik.info>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
