Commit Graph

591 Commits

Author SHA1 Message Date
jean-michel.hautbois@vodalys.com
80f4944ec2 [media] media: adv7604: CP CSC uses a different register on adv7604 and adv7611
The bits are the same, but register is 0xf4 on ADV7611 instead of 0xfc.
When reading back the value in log_status, differentiate both.

Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:56:21 -03:00
jean-michel.hautbois@vodalys.com
5851462531 [media] media: i2c: ADV7604: In free run mode, signal is locked
The CP_NON_STD_VIDEO bit indicates an input not aligned with DV timings.
If there is no input, and chip is in free run mode, consider we are locked.

Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
[hans.verkuil@cisco.com: put both conditions in one 'if']
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:54:22 -03:00
Mauro Carvalho Chehab
7e4f23d53d [media] cx25840: better document the media pads
Use an enum to better document the media pads.

No functional changes.

Suggested-by: Prabhakar Lad <prabhakar.csengg@gmail.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-26 08:45:58 -03:00
Mauro Carvalho Chehab
db74935905 [media] cx25840: fix return logic when media entity init fails
There's no need to free state, as it was allocated via devm_kzalloc().

Also, let's return the error code, instead of something else.

Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-26 08:45:42 -03:00
Mauro Carvalho Chehab
18e8d630cc [media] cx25840: better document the media controller TODO
Analog video inputs are the tuner, plus composite, svideo, etc,
 e. g. the input pat should actually be like:

                ___________
TUNER --------> |         |
                |         |
SVIDEO .......> | cx25840 |
                |         |
COMPOSITE1 ...> |_________|

(in the above, dashes represent the enabled link, and periods
represent the disabled ones)

In other words, if we want to properly represent the pipeline,
it should be possible to see via the media controller if the tuner
is being used as an image source, or if the source is something else.

I didn't map those other inputs here yet, due to a few things:
- The extra inputs would require subdevs that won't be controlled
- I was in doubt about the best way for doing that
- That would likely require some extra setup for cx25840 caller
  drivers, in order to represent what of the possible internal
  inputs are actually used on each specific board

Actually, at least for now, I was unable to see much benefit
on adding such map now, so let's just document it, as this could
be added later on, as needed.

Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-26 08:44:40 -03:00
Mauro Carvalho Chehab
8cd61969c8 [media] cx25840: fill the media controller entity
Instead of keeping the media controller entity not initialized,
fill it and create the pads for cx25840.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-13 21:10:14 -02:00
Lars-Peter Clausen
08b717c2ae [media] adv7180: Add fast switch support
In fast switch mode the adv7180 (and similar) can lock onto a new signal
faster when switching between different inputs. As a downside though it is
no longer able to auto-detect the incoming format.

The fast switch mode is exposed as a boolean v4l control that allows
userspace applications to either enable or disable fast switch mode.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:51:38 -02:00
Lars-Peter Clausen
851a54effb [media] adv7180: Add I2P support
Some of the devices supported by this driver have a interlaced-to-
progressive converter which can optionally be enabled. This patch adds
support for enabling and disabling the I2P converter on such devices.

I2P mode can be enabled by selecting V4L2_FIELD_NONE instead of
V4L2_FIELD_INTERLACED for the format.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:50:54 -02:00
Lars-Peter Clausen
b37135e395 [media] adv7180: Add support for the adv7280-m/adv7281-m/adv7281-ma/adv7282-m
This patch adds support for the adv7280-m/adv2781-m/adv7281-ma/adv7282-m
devices to the adv7180 driver. They are very similar to the
adv7280/adv7281/adv7282 but instead of parallel video out they feature a
MIPI CSI2 transmitter.

The CSI2 transmitter is configured via a separate I2C address, so we need to
register a dummy device for it.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:49:20 -02:00
Lars-Peter Clausen
bf7dcb8067 [media] adv7180: Add support for the adv7280/adv7281/adv7282
This patch adds support for the adv7280/adv7281/adv7282 devices to the
adv7180 driver. They are very similar to the adv7182, the main difference
from the drivers point of view are some different tuning constants for
improved video performance.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:48:38 -02:00
Lars-Peter Clausen
c5ef8f8c5d [media] adv7180: Add support for the adv7182
This patch adds support for the adv7182 to the adv7180 driver. The adv7182
is similar to the adv7180, the main difference from the driver's point of
view is how the video input and how the input format are selected.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:47:52 -02:00
Lars-Peter Clausen
f5dde49b8f [media] adv7180: Prepare for multi-chip support
The adv7180 is part of a larger family of device, which have all a very
similar register map layout. This patch prepares the adv7180 driver for
support for multiple different devices. For now the only difference we care
about is the number of input channel configurations. Also the way the input
format is configured slightly differs between some devices.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:47:19 -02:00
Lars-Peter Clausen
3e35e33c08 [media] adv7180: Consolidate video mode setting
We have basically the same code to set the video standard in init_device()
and adv7180_s_std(). Factor this out into a common helper function.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:46:33 -02:00
Lars-Peter Clausen
d5d51a827b [media] adv7180: Add media controller support
Add media controller support to the adv7180 driver by registering a media
entity instance for it as well as implementing pad ops for configuring the
format.

As there currently don't seem to be any users of the video ops format
operations those are removed as well in this patch.

Also set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so it is
possible to create a subdevice device node.

Since the driver now depends on VIDEO_V4L2_SUBDEV_API all drivers which
select the driver need to depend on that symbol as well.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:45:35 -02:00
Lars-Peter Clausen
c18818e990 [media] adv7180: Reset the device before initialization
Reset the device when initializing it so it is in a good known state and the
assumed register settings matches the actual register settings.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:40:50 -02:00
Lars-Peter Clausen
3999e5d01d [media] adv7180: Do implicit register paging
The ad7180 has multiple register pages which can be switched between by
writing to a register. Currently the driver manually switches between pages
whenever a register outside of the default register map is accessed and
switches back after it has been accessed. This is a bit tedious and also
potential source for bugs.

This patch adds two helper functions that take care of switching between
pages and reading/writing the register. The register numbers for registers
are updated to encode both the page (in the upper 8-bits) and the register
(in the lower 8-bits) numbers.

Having multiple pages means that a register access is not a single atomic
i2c_smbus_write_byte_data() or i2c_smbus_read_byte_data() call and we need
to make sure that concurrent register access does not race against each
other.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:40:14 -02:00
Lars-Peter Clausen
029d617791 [media] adv7180: Cleanup register define naming
Consistently prefix register defines with ADV7180_REG. Also remove the "ADI"
from register names, the ADV7180 prefix should provide enough of a namespace
separation.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:30:32 -02:00
Lars-Peter Clausen
f3e991d418 [media] adv7180: Pass correct flags to request_threaded_irq()
Most IRQ controllers support different types of interrupts. The adv7180
generates falling edge interrupts, so make sure to pass IRQF_TRIGGER_FALLING
to request_threaded_irq() so the IRQ controller is configured for the
correct mode.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:15:53 -02:00
Lars-Peter Clausen
fa5721d159 [media] adv7180: Do not request the IRQ again during resume
Currently the IRQ is requested from within the init_device() function. This
function is not only called during device probe, but also during resume
causing the driver to try to request the IRQ again. Move requesting the IRQ
from init_device() to the probe function to make sure that it is only
requested once.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 11:15:03 -02:00
Josh Wu
650b1815ff [media] ov2640: use the v4l2 size definitions
Reuse the v4l2 size definitions from v4l2-image-sizes.h.
So we can remove the rudundent definitions from ov2640.c.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-02-02 10:40:56 -02:00
Sakari Ailus
cb88d7384e [media] smiapp: Don't compile of_read_number() if CONFIG_OF isn't defined
of_read_number() is defined in of.h but does not return an error code, so
that non-of implementation could simply return an error.

Temporarily work around this until of_read_number() can be replaced by
of_property_read_u64_array().

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-01-29 17:59:22 -02:00
Martin Bugge
09f90c53ac [media] adv7842: simplify InfoFrame logging
Use the new logging functions from the hdmi module.

Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-01-27 10:19:48 -02:00
Fabio Estevam
7657e0647c [media] adv7180: Remove the unneeded 'err' label
There is no need to jump to the 'err' label as we can simply return the error
code directly and make the code shorter.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-01-27 10:15:58 -02:00
Rickard Strandqvist
43abdd6b6b [media] media: i2c: adv7604: Remove some unused functions
Removes some functions that are not used anywhere:
test_read() edid_read_block() dpp_write() dpp_read()
esdp_write() esdp_read() cec_write_clr_set()

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-01-27 10:11:02 -02:00
Rickard Strandqvist
05a2ea7835 [media] media: i2c: adv7604.c: Remove some unused functions
Removes some functions that are not used anywhere:
vblanking() hblanking()

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-01-27 10:09:42 -02:00
Sakari Ailus
3b1635e02e [media] smiapp: Add parentheses to macro arguments used in macros
This makes the macros a little bit safer.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:51:30 -02:00
Sakari Ailus
0d825a1226 [media] smiapp: Replace pll_flags quirk with more generic init quirk
The pll_flags quirk just returned the extra PLL flags the sensor required,
but the init quirk is far more versatile. It can be used to perform any
extra initialisation needed by the sensor, including allocating memory for
sensor specific struct and creating sensor specific new controls.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:50:25 -02:00
Sakari Ailus
5313c00266 [media] smiapp: Move enumerating available media bus codes later
As the controls creation is separated in two sections, the available media
bus codes and link frequencies can be enumerated later on.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:49:01 -02:00
Sakari Ailus
2e9f3c1c44 [media] smiapp: Separate late controls from the rest
The default values and limits for certain controls need the knowledge of
available media bus codes or link frequencies. Create such controls later
on, so that most of the initialisation of the sensor has already been done
when the init quirk is called.

[mchehab@osg.samsung.com: make checkpatch.pl happier]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:47:51 -02:00
Sakari Ailus
6208aebd33 [media] smiapp: Clean up smiapp_init_controls()
Clean up smiapp_init_controls() by adding newlines to appropriate places and
by removing superfluous error handling. The caller will clean up control
handlers in any case if the function fails.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:44:32 -02:00
Sakari Ailus
f7350a034a [media] smiapp: Free control handlers in sub-device cleanup
Also call smiapp_cleanup() in smiapp_remove(), replacing code that did the
same than the function.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:43:33 -02:00
Sakari Ailus
0691b40e88 [media] smiapp: Access flash capabilities through limits
The flash capability register is already read as part of the limit
registers. Do no access it separately; instead use the value from the
limits.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:42:56 -02:00
Sakari Ailus
4c94468459 [media] smiapp: Fully probe the device in probe
In the case of platform data, ISPs that provide clocks to the sensor must
probe before the sensor does. Accessing the sensor does require the clocks,
and thus, probe cannot access the sensor in such a system.

This limitation does not exist in the case of the DT. Perform all
initialisation except Media entity initialisation, link creation and
sub-device registration in probe.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:37:50 -02:00
Sakari Ailus
7095108b16 [media] smiapp: Split sub-device initialisation off from the registered callback
The registered callback is called by the V4L2 async framework after the
bound callback. This allows separating the functionality in the registered
callback so that on DT based systems only sub-device registration is done
there.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:36:11 -02:00
Sakari Ailus
390a5fa5bd [media] smiapp: Obtain device information from the Device Tree if OF node exists
Platform data support is retained.

of_property_read_u64_array() isn't used yet as it's not in yet.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:35:29 -02:00
Sakari Ailus
575ea5b3a4 [media] smiapp: The sensor only needs a single clock, name may be NULL
The SMIA compatible sensors only need a single clock.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:33:05 -02:00
Sakari Ailus
f73108eb8e [media] smiapp: Register async subdev
Register and unregister async sub-device for DT.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:30:48 -02:00
Sakari Ailus
3d9bb7a620 [media] smiapp: Don't give the source sub-device a temporary name
The source sub-device's name will be overwritten shortly. Don't give it a
name in the meantime.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:30:09 -02:00
Sakari Ailus
8c20ee6e92 [media] smiapp-pll: include linux/device.h in smiapp-pll.c, not in smiapp-pll.h
struct device has a forward declaration in the header already. The header is
only needed in the .c file.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:29:01 -02:00
Sakari Ailus
29867e2feb [media] smiapp: Remove FSF's address from the license header
Remove FSF's address information from the license header in the smiapp
driver and the smiapp-pll PLL calculator. This should no longer be needed,
and would be rendered outdated in case the FSF chooses to relocate its
office.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Timo Ahonen <timo.ahonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 11:27:47 -02:00
Hans Verkuil
0348bb1a7a [media] s5k5baf: fix sparse warnings
drivers/media/i2c/s5k5baf.c:1796:33: warning: duplicate const
drivers/media/i2c/s5k5baf.c:379:24: warning: cast to restricted __le16
drivers/media/i2c/s5k5baf.c:437:11: warning: incorrect type in assignment (different base types)
drivers/media/i2c/s5k5baf.c:445:16: warning: incorrect type in return expression (different base types)

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 10:47:15 -02:00
Hans Verkuil
7c7586bb3c [media] s5k6aa: fix sparse warnings
drivers/media/i2c/s5k6aa.c:351:16: warning: cast to restricted __be16
drivers/media/i2c/s5k6aa.c:351:16: warning: cast to restricted __be16
drivers/media/i2c/s5k6aa.c:351:16: warning: cast to restricted __be16
drivers/media/i2c/s5k6aa.c:351:16: warning: cast to restricted __be16

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 10:46:00 -02:00
Hans Verkuil
b75f2d16cb [media] s5k4ecgx: fix sparse warnings
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:344:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:354:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:364:24: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:366:23: warning: cast to restricted __le16

The get_unaligned_le*() functions return the value using cpu endianness,
so calling le*_to_cpu is wrong.

It hasn't been not noticed because this code has only been run on little
endian systems, so le*_to_cpu doesn't do anything.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 10:45:29 -02:00
Hans Verkuil
d3acd83e6e [media] m5mols: fix sparse warnings
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16

The be16_to_cpu conversions in m5mols_get_version() are not needed since the
data is already using cpu endianness. This was never noticed since these
version fields are never used.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 10:44:50 -02:00
Hans Verkuil
584ca0252a [media] media/i2c/Kconfig: drop superfluous MEDIA_CONTROLLER
These drivers depend on VIDEO_V4L2_SUBDEV_API, which in turn
depends on MEDIA_CONTROLLER. So it is sufficient to just depend
on VIDEO_V4L2_SUBDEV_API.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-22 18:15:45 -02:00
Hans Verkuil
1a023feb9c [media] v4l2 subdevs: replace get/set_crop by get/set_selection
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-22 18:11:34 -02:00
Hans Verkuil
215cedec37 [media] media: remove emacs editor variables
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-22 17:52:20 -02:00
Linus Torvalds
0ec28c37c2 media updates for v3.19-rc1
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUksm/AAoJEAhfPr2O5OEV7GIP/1nm2rcf16+6Y7nhjWLgPmlU
 uG9fNUMm7qvFHryCr4RwmTBnCv63Nn/5BFRcXdpAA2gHOtADcHCDNJbtSX+GRN5F
 I0C5gbLbQVd7l/GFsiGTsBScInAQB+ZN0WNyPbF0OCGLuzzRlexadAYTZufnNiNN
 nYCINIBub0jUPJaIrbm/qDAbazS7fxTO9HAdMcJGtexPCO/Gj92+4s8NXI+N3hxk
 Cj87EPsk6i6GA1BM0oVmDWK0dQjgFm+ONMBc8vhFOyVzCXb7pjHg53n1zZ0e0TDt
 jm/h/oIJuWyH/isEuwcNPTBxf2E9EOv8g66V9mDN1i7zsTEf9Bs08fPigalfJ84x
 5S5GBaHEGIu8d2PgqaqxmFO1COyk+xoj9O0Iwx8uabYtyRtgUVaEtsfyHWU2ZiAh
 3wqmtHSK5mt835h9wzjxs18apnRhTwEhfQWzFdiCFxkDPz3vPmfWbm+8WHChtYJh
 j0oSJwzK9uAcYwG8WZi643WduIyrXiDqaglWyBg+7c2k3NhP76W5CpLhjZ+8PrYt
 I6Jf+gZL/Joq5bMQx6itajgE5IIhAfxmdyaYIBqmlXuQ/88zrw7JBwu6q22jSVbq
 +QaURaSJ6qOLYj6S/ip93KPVsUXmfdE1JttuLp4ie7r0Q8zOahr4dPQ/xAwATtY/
 Jeo+d7AI4tLWQcIDKIWi
 =1rPM
 -----END PGP SIGNATURE-----

Merge tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media

Pull second set of media updates from Mauro Carvalho Chehab:

 - Move drivers for really old legacy hardware to staging.  Those are
   using obsolete media kAPIs and are for hardware that nobody uses for
   years.  Simply not worth porting them to the new kAPIs.  Of course,
   if anyone pops up to fix, we can move them back from there

 - While not too late, do some API fixups at the new colorspace API,
   added for v3.19

 - Some improvements for rcar_vin driver

 - Some fixups at cx88 and vivid drivers

 - Some Documentation fixups

* tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] bq/c-qcam, w9966, pms: move to staging in preparation for removal
  [media] tlg2300: move to staging in preparation for removal
  [media] vino/saa7191: move to staging in preparation for removal
  [media] MAINTAINERS: vivi -> vivid
  [media] cx88: remove leftover start_video_dma() call
  [media] cx88: add missing alloc_ctx support
  [media] v4l2-ioctl: WARN_ON if querycap didn't fill device_caps
  [media] vivid: fix CROP_BOUNDS typo for video output
  [media] DocBook media: update version number and document changes
  [media] vivid.txt: document new controls
  [media] DocBook media: add missing ycbcr_enc and quantization fields
  [media] v4l2-mediabus.h: use two __u16 instead of two __u32
  [media] rcar_vin: Fix interrupt enable in progressive
  [media] rcar_vin: Enable VSYNC field toggle mode
  [media] rcar_vin: Add scaling support
  [media] rcar_vin: Add DT support for r8a7793 and r8a7794 SoCs
  [media] rcar_vin: Add YUYV capture format support
2014-12-18 20:14:49 -08:00
Hans Verkuil
c1d9e03d4e [media] vino/saa7191: move to staging in preparation for removal
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.

So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-16 23:21:42 -02:00
Linus Torvalds
2183a58803 media updates for v3.19-rc1
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUhxhbAAoJEAhfPr2O5OEV4JwP/2I7D2KGz5tdNGDAh1H8+swR
 hoj3tX7HLhwBmF6XIUlMYbk5L/ClDace6kcjT6OjwJ9SktrrKks6ZSsYsBjCIyOC
 yS7xNQArUKzWk4vV+uJVAvtF8V57LLFul8dhHk0JJwAxrkWnPvDdfJNs4PhUAkgn
 1i0PPshNo5Ow/+4YMiOjEDR+q9TMSUUzaq5zkPF7AFCnykuJ1wUJwUE0qjTfGi+4
 gl1yMye0TEawTYSM8h/+Lh7wosNFZYcXg85r04A6a8h6GLgg0h6KSOJjyPITmQ+j
 hLdtyiYs8a6XT+Y8o416zxpbSozo7KXCUTtet/N5g+lgQMqZqSd9WxE52SOY+kfd
 UVeob0VfWR0xdDzaJp5rLQ/MQ16RTHaHppgUidFxxGe9D5f9JM/88I0OfwNzl4uO
 cv2cyeNktHH6bcjfOGqxSVmZWgAm6q6qU7MN07PoN+5TcUlYTAOi1WLE5K+7HGgw
 CxzOZ61oxi/OO1FapaVoipq6ycjltTql2kbcARvmrRrbge0ocAqHxHqFyUbDDhNw
 Wn/O6VzLfpW0vGTacC6+xcUSpIhwajJ80UJAOqJP8sw0Xtmian5Lcs6gVzxwkOdU
 36Po4RRGFqsG6Sq3HR+toNwKt/nHNEFkJwYcNFHdvBiXTEYYkMe6MccUxxb3i/iI
 KxB1s51zVy9t3PqjP+3J
 =i7gx
 -----END PGP SIGNATURE-----

Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media

Pull media updates from Mauro Carvalho Chehab:
 - Two new dvb frontend drivers: mn88472 and mn88473
 - A new driver for some PCIe DVBSky cards
 - A new remote controller driver: meson-ir
 - One LIRC staging driver got rewritten and promoted to mainstream:
   igorplugusb
 - A new tuner driver (m88rs6000t)
 - The old omap2 media driver got removed from staging.  This driver
   uses an old DMA API and it is likely broken on recent kernels.
   Nobody cared enough to fix it
 - Media bus format moved to a separate header, as DRM will also use the
   definitions there
 - mem2mem_testdev were renamed to vim2m, in order to use the same
   naming convention taken by the other virtual test driver (vivid)
 - Added a new driver for coda SoC (coda-jpeg)
 - The cx88 driver got converted to use videobuf2 core
 - Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
   cores
 - Lots of other fixes, improvements and cleanups on the drivers.

* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
  [media] mn88473: One function call less in mn88473_init() after error
  [media] mn88473: Remove uneeded check before release_firmware()
  [media] lirc_zilog: Deletion of unnecessary checks before vfree()
  [media] MAINTAINERS: Add myself as img-ir maintainer
  [media] img-ir: Don't set driver's module owner
  [media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
  [media] img-ir/hw: Drop [un]register_decoder declarations
  [media] img-ir/hw: Fix potential deadlock stopping timer
  [media] img-ir/hw: Always read data to clear buffer
  [media] redrat3: ensure dma is setup properly
  [media] ddbridge: remove unneeded check before dvb_unregister_device()
  [media] si2157: One function call less in si2157_init() after error
  [media] tuners: remove uneeded checks before release_firmware()
  [media] arm: omap2: rx51-peripherals: fix build warning
  [media] stv090x: add an extra protetion against buffer overflow
  [media] stv090x: Remove an unreachable code
  [media] stv090x: Some whitespace cleanups
  [media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
  [media] si2168: add support for firmware files in new format
  [media] si2168: debug printout for firmware version
  ...
2014-12-11 11:49:23 -08:00