As per request of rmk, the options should be sorted alphabetically.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the legacy ARM LED code for simpad devices and
register a stadard LED platform device using GPIO line
instead.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register keyboard, polled keyboard and I2C platform
devices based on GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- prepend CS3 accessors by simpad_ to indicate they
are specific to simpad devices.
- use spinlock to protect shadow register.
- implement 8 read-only pins.
- use readl/writel macros so barriers are used where
necessary.
- register CS3 as GPIO controller with 24 pins
(16 output only and 8 input only).
- fix PCMCIA driver to access the read-only pins
rather than the shadow register for status bits.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ucb1x00 GPIO definitions to simpad.h and add gpio_base
to ucb1x00 platform device so the pins are available using
the GPIO API.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, show_regs calls __backtrace which does
nothing if CONFIG_FRAME_POINTER is not set. Switch to
dump_stack which handles both CONFIG_FRAME_POINTER and
CONFIG_ARM_UNWIND correctly.
__backtrace is now superseded by dump_stack in general
and show_regs was the last caller so remove __backtrace
as well.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current Versatile Express CPU hotplug code includes a hardcoded WFI
instruction, in ARM encoding. When the kernel is compiled in Thumb-2
mode, this is invalid and causes the machine to hang hard when a CPU
is offlined.
Using the wfi macro (which uses the appropriate assembler mnemonic)
causes the correct instruction to be emitted in either case. As a
consequence of this change, an apparently vestigial "cc" clobber is
dropped from the asm (the macro uses "memory" only).
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When v6 and >=v7 boards are supported in the same kernel, the
__und_usr code currently makes a build-time assumption that Thumb-2
instructions occurring in userspace don't need to be supported.
Strictly speaking this is incorrect.
This patch fixes the above case by doing a run-time check on the
CPU architecture in these cases. This only affects kernels which
support v6 and >=v7 CPUs together: plain v6 and plain v7 kernels
are unaffected.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When testing whether a Thumb-2 instruction is 32 bits long or not,
the masking done in order to test bits 11-15 of the first
instruction halfword won't affect the result of the comparison, so
remove it.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU architecture really should not be changing at runtime, so
make it a global variable instead of a function.
The cpu_architecture() function declared in <asm/system.h> remains
the correct way to read this variable from C code.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
uImages need a load address specified. This makes them
incompatible with multiple zreladdrs. Catch this error
before building an uImage so that we do not end up with
broken uImages. The load address can still be specified
with LOADADDR= on the command line.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without CONFIG_AUTO_ZRELADDR being set the kernel needs a single
zreladdr for building zImages. Bail out if we detect multiple
zreladdrs without CONFIG_AUTO_ZRELADDR.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With d8ecc5c (kbuild: asm-generic support, 2011-04-27) we can
remove a handful of asm-generic wrappers in ARM code. Since the
generic version of sizes.h doesn't contain SZ_48M, we replace
the 4 users of SZ_48M with the equivalent SZ_32M + SZ_16M.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
we save the l2x0 registers at the first initialization, and platform codes
can get them to restore l2x0 status after wakeup.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
this patch fixes the error in Rob Herring's
ARM: 7009/1: l2x0: Add OF based initialization
http://www.spinics.net/lists/arm-kernel/msg131123.html
it has been in rmk/for-next with commit 41c86ff5b
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
using cpu_relax in busy loops is a well-known idiom in the kernel.
It's more for documentation purposes than technically needed here.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds probing for ARM L2x0 cache controllers via device tree. Support
includes the L210, L220, and PL310 controllers. The binding allows setting
up cache RAM latencies and filter addresses (PL310 only).
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defaulting to DEBUG_ICEDCC will cause systems to hang during boot unless
a hardware debugger is listening to the debug comms. channel.
This patch adds a dummy UART option as the default DEBUG_LL choice which
requires the platform to do the right thing.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DEBUG_ICEDCC support is just another DEBUG_LL choice and
selecting it along with other DEBUG_LL options doesn't make
much sense. Put it into the DEBUG_LL choice to avoid confusion.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM patch 7072/1 (debug: use kconfig choice for selecting
DEBUG_LL UART) didn't notice that the Kconfigs relied on being
unselected to configure a different serial port. Since there is
no NONE option in a choice menu, explicitly add the other option
so that both serial ports can be selected.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabled DEBUG_LL hardcodes the UART address into the kernel and results
in a non-portable kernel image. Since this option is only intended for
use when debugging early boot failures, supporting multiple platforms
in such a configuration is not the intended use-case.
This patch documents this limitation in the DEBUG_LL Kconfig help text,
so that users are aware of the portability restrictions that are associated
with enabling low-level debugging support.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabling CONFIG_DEBUG_LL (which is required for earlyprintk) hardwires
the debug UART address into the kernel, so that we can print before the
platform is initialised.
If the user inadvertently selects multiple platforms with DEBUG_LL
enabled, the UART address may not be correct and will likely cause the
kernel to hang in the very early stages of boot.
This patch, based on a skeleton from Russell, uses a Kconfig choice for
selecting the DEBUG_LL UART, therefore allowing the user to make a
choice about the supported platform when DEBUG_LL is enabled.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The definition of __exception_irq_entry for
CONFIG_FUNCTION_GRAPH_TRACER=y needs linux/ftrace.h, but this creates a
circular dependency with it's current home in asm/system.h. Create
asm/exception.h and update all current users.
v4: - rebase to rmk/for-next
v3: - remove redundant includes of linux/ftrace.h
v2: - document the usage restricitions of __exception*
Cc: Zoltan Devai <zdevai@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to be able to handle localtimer directly from C code instead of
assembly code, introduce handle_local_timer(), which is modeled after
handle_IRQ().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to be able to handle IPI directly from C code instead of
assembly code, introduce handle_IPI(), which is modeled after handle_IRQ().
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When Cortex-A9 MPCore resumes from Dormant or Shutdown modes,
SCU needs to be re-enabled. This patch removes __init annotation
from function scu_enable(), so that platform resume procedure can
call it to re-enable SCU.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GIC driver must convert logical CPU numbers passed in from Linux
into physical CPU numbers that are understood by the hardware.
This patch uses the new cpu_logical_map macro for performing the
conversion inside the GIC driver.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow booting Linux on a CPU with physical ID != 0, we need to
provide a mapping from the logical CPU number to the physical CPU
number.
This patch adds such a mapping and populates it during boot.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The affinity between ARM processors is defined in the MPIDR register.
We can identify which processors are in the same cluster,
and which ones have performance interdependency. We can define the
cpu topology of ARM platform, that is then used by sched_mc and sched_smt.
The default state of sched_mc and sched_smt config is disable.
When enabled, the behavior of the scheduler can be modified with
sched_mc_power_savings and sched_smt_power_savings sysfs interfaces.
Changes since v4 :
* Remove unnecessary parentheses and blank lines
Changes since v3 :
* Update the format of printk message
* Remove blank line
Changes since v2 :
* Update the commit message and some comments
Changes since v1 :
* Update the commit message
* Add read_cpuid_mpidr in arch/arm/include/asm/cputype.h
* Modify header of arch/arm/kernel/topology.c
* Modify tests and manipulation of MPIDR's bitfields
* Modify the place and dependancy of the config
* Modify Noop functions
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is unneeded and causes an abort on the SPMP8000 platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zoltan Devai <zoss@devai.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Per the text in Documentation/SubmitChecklist as below, we should
explicitly have header linux/errno.h in localtimer.h for ENXIO
reference.
1: If you use a facility then #include the file that defines/declares
that facility. Don't depend on other header files pulling in ones
that you use.
Otherwise, we may run into some compiling error like the following one,
if any file includes localtimer.h without CONFIG_LOCAL_TIMERS defined.
arch/arm/include/asm/localtimer.h: In function ‘local_timer_setup’:
arch/arm/include/asm/localtimer.h:53:10: error: ‘ENXIO’ undeclared (first use in this function)
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using COHERENT_LINE_{MISS,HIT} for cache misses and references
respectively is completely wrong. Instead, use the L1D events which
are a better and more useful approximation despite ignoring instruction
traffic.
Reported-by: Alasdair Grant <alasdair.grant@arm.com>
Reported-by: Matt Horsnell <matt.horsnell@arm.com>
Reported-by: Michael Williams <michael.williams@arm.com>
Cc: stable@kernel.org
Cc: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit af337f3e63
"ARM: S3C2443: Move parts of the clock code to common clock file",
the init_clocks array is moved to arch/arm/plat-s3c24xx/s3c2443-clock.c.
Now we call s3c_register_clocks for init_clocks in s3c2443_common_init_clocks.
Thus we can remove the empty init_clocks array here and remove the
redundant s3c_register_clocks call for init_clocks in s3c2443_init_clocks.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 uses hsmmc1 as its only hsmmc device and for S3C2416/S3C2450
it's the second hsmmc channel with the same PCLKCON bit.
The hsmmc-if clocks on both systems already got a devname, as did
the hsmmc pclk for hsmmc0 on the S3C2416. So to make it possible to
identify the hsmmc1 pclk on S3C2416 add the correct devname for it.
The sclk name on S3C2443 also is s3c-sdhci.1.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously the fclk rate was calculated by dividing the pll through
the divider value of the armdiv. With a real armdiv clk in place it's
possible to simply read its value, which does essentially the same.
This change makes the whole fdiv_fn function pointers supplied to
s3c2443_common_init_clocks and s3c2443_common_setup_clocks
obsolete, so remove it too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cpufreq uses frequencies in kHz and not Hz, so set_rate and round_rate
would be called with a frequency of 266666000 instead of 266666666 but
the clock functions check for rates smaller or equal to the targetrate.
As the armdiv does not support steps this small we can accommodate
this by simply also setting the last 3 digits of the calculated rate
to zero.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The armdiv array may contain unset divider values.
Check the relevant value to prevent division by zero
errors. Also check for set nr_armdiv and armdivmask
before meddling with clkdiv0.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The system-layout of the armdiv and armclk is common to
S3C2443/S3C2416/S3C2450 and only differs in the array of
possible dividers. Therefore it is possible to reuse the
clock definitions for all of these SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed for making the armdiv clock common to S3C2443
and S3C2416/2450.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C2416/2450 has only 3 bits for the armdiv setting instead
of the 4 bits of the S3C2443.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add voltage regulator and platform data definition for M-5MOLS sensor
and MIPI-CSI receiver drivers. Add CAM power domain dependencies for
FIMC device and set up camera port A GPIO. Configure I2C0 bus timings.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables multi-format codec (MFC) support on ORIGEN board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ADC of the S3C2416/2450 SoC is 10 or 12 bit wide, has its
source selection in the register base+0x18 and its width
selection in bit 03 of the ADCCON register.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C2443-adc is 10 bit wide and has its mux-select
in an extra register at base+0x18
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Refresh tegra_defconfig:
New options enabled: RTC, SPI, USB and USB_STORAGE together with
corresponding tegra drivers. Also enable some of the common usb ethernet
adapters.
Enable Tegra ALSA/ASoC/sound support, including drivers for TrimSlice,
and WM8903-based platforms such as Harmony and Seaboard.
Finally, enable new merged boards (Ventana) and the generic devicetree board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Without this, the PMC continually detects an interrupt when the PMU_IRQ
line is high, causing the tps6686x IRQ handler thread to hog an entire
CPU.
This change was originally written by Wei Ni <wni@nvidia.com> for Seaboard
in the ChromeOS kernel.
Long-term, this should probably be moved into some kind of PMU driver,
or perhaps integrated into the GPIO/IRQ/pinmux system?
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for ventana pinmuxing as a seaboard derivative. This is a cut down
version of work done by Jong Kim <jongk@nvidia.com>.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch splits out the common part of pinmux and GPIO initialization for
seaboard and derived boards. This code is based on work done by Jong Kim
<jongk@nvidia.com>.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use ioremap to obtain access to registers instead of using static
mappings. This reduces the number of users of the static mappings, which
will eventually allow them to be removed.
Note that on Tegra30, the number of register "banks" will decrease to 2,
and the packing of specific bits into registers will change significantly.
That's why this change adds the "*_bank" fields to the pingroup tables,
rather than implementing some more hard-coded scheme.
Also, completely remove the implementation of suspend/resume; Tegra doesn't
yet support suspend/resume, and the implementation is complex for the
general pinmux driver:
* Not all registers are used within each bank, so we probably shouldn't
just iterate over every register in the bank, and save/restore it,
since that would mean touching undefined registers.
* Registers are shared between pingroups, so we can't simply iterate over
each pingroup, and save/restore the registers it uses.
It'd probably be best have probe() calculate a bitmask of actually-used
registers for each bank, and have suspend/resume iterate over those
bitmaps.
Oh, and Real Soon Now, I should be looking into converting this driver to
the new pinmux/pinctrl subsystem, so I didn't want to put too much work
into the current incarnation.
v2: s/space/bank/ to match comments on reg_* fields in pinmux.h.
Re-order bank/reg parameters to pg_readl/pg_writel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Resolves lots of sparse warnings:
arch/arm/mach-tegra/devices.c:102:24: warning: symbol 'tegra_i2c_device1' was not declared. Should it be static?
arch/arm/mach-tegra/devices.c:112:24: warning: symbol 'tegra_i2c_device2' was not declared. Should it be static?
arch/arm/mach-tegra/devices.c:122:24: warning: symbol 'tegra_i2c_device3' was not declared. Should it be static?
arch/arm/mach-tegra/devices.c:132:24: warning: symbol 'tegra_i2c_device4' was not declared. Should it be static?
[...]
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Two static functions that are not exported:
arch/arm/mach-tegra/cpu-tegra.c:59:5: warning: symbol 'tegra_verify_speed' was not declared. Should it be static?
arch/arm/mach-tegra/cpu-tegra.c:64:14: warning: symbol 'tegra_getspeed' was not declared. Should it be static?
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Type fix:
arch/arm/mach-tegra/cpu-tegra.c:144:14: warning: incorrect type in argument 5 (different signedness)
arch/arm/mach-tegra/cpu-tegra.c:144:14: expected unsigned int *index
arch/arm/mach-tegra/cpu-tegra.c:144:14: got int *<noident>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
None of them are used externally.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not used externally, and certainly don't need to be exported.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not exported and not used externally.
Also, fix return type. Due to new return type, errors can't be returned
so WARN_ON instead of returning error if a bad parameter is specified.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not exported and not used externally.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not exported and not used externally.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
arch/arm/mach-tegra/pcie.c:908:12: warning: symbol 'tegra_pcie_init' was not declared. Should it be static?
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/pcie.c:678:8: warning: cast removes address space of expression
arch/arm/mach-tegra/pcie.c:678:8: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-tegra/pcie.c:678:8: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-tegra/pcie.c:678:8: got unsigned int
arch/arm/mach-tegra/pcie.c:678:8: warning: cast removes address space of expression
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/tegra2_clocks.c:921:34: warning: Using plain integer as NULL pointer
arch/arm/mach-tegra/tegra2_clocks.c:1462:4: warning: Using plain integer as NULL pointer
arch/arm/mach-tegra/tegra2_clocks.c:1864:4: warning: Using plain integer as NULL pointer
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/tegra2_clocks.c:180:2: warning: cast removes address space of expression
arch/arm/mach-tegra/tegra2_clocks.c:180:2: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-tegra/tegra2_clocks.c:180:2: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-tegra/tegra2_clocks.c:180:2: got unsigned int
arch/arm/mach-tegra/tegra2_clocks.c:180:2: warning: cast removes address space of expression
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/timer.c:75:2: warning: cast removes address space of expression
arch/arm/mach-tegra/timer.c:75:2: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-tegra/timer.c:75:2: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-tegra/timer.c:75:2: got unsigned int
arch/arm/mach-tegra/timer.c:75:2: warning: cast removes address space of expression
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Provide __iomem annotation for IO_*_VIRT pointers, which will propagate
up through IO_TO_VIRT(). Also fixes a 0 to NULL conversion of the base
case to silence sparse.
Unfortunately map_desc takes an unsigned long for the pointer instead of
a void __iomem *. For now, cast explicitly for those cases.
v2: change define to use IOMEM() like many other mach platforms per
comment from Russell.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Given that we want the default to not have any <mach/memory.h> and given
that there are now fewer cases where it is still provided than the cases
where it is not at this point, this makes sense to invert the logic and
just identify the exception cases.
The word "need" instead of "have" was chosen to construct the config
symbol so not to suggest that having a mach/memory.h file is actually
a feature that one should aim for.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This also removes the mach/s3c2400 version which was probably never used
due to the fact that we have this line in arch/arm/Makefile:
machine-$(CONFIG_ARCH_S3C2410) := s3c2410 s3c2400 [...]
This is later used to construct the search path for:
The compiler would be looking into mach-s3c2410 and picking up this
version first. Any config that was actually expecting the mach-s3c2400
version was therefore producing a broken kernel binary. Not relying on
any of them anymore would fix that issue.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This adds a driver for the U300 pinmux portions of the system
controller "SYSCON". It also serves as an example of how to use
the pinmux subsystem. This driver also houses the platform data
for the only supported platform.
This deletes the old U300 driver in arch/arm/mach-u300 and
replace it with a driver using the new subsystem.
The new driver is considerably fatter than the old one, but it
also registers all 467 pins of the system and adds the power
and EMIF pin groups and corresponding functions. The idea
is to use this driver as a a reference for other
implementation so it needs to be as complete and verbose
as possible.
Reviewed-by: Barry Song <21cnbao@gmail.com>
[Fixup for changed function names and semantics in the v10 patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the platform device definitions from boards code to plat-samsung
to avoid multiple instances when multiple board support is compiled in.
The boards should select at least S5P_DEV_FIMC0 to enable FIMC support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of S3C2443 and S3C2416 contain quirks not present
in the stock S3C24xx adc. Therefore allow them to alter the
device name via s3c_adc_setname.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mux bits in the adccon register should be cleared only
if muxing is really done in ADCCON and not another register.
This patch introduces a conditional for this.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of the S3C2443 and S3C2416 define some
additional registers and bits.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C64xx CPUs have TCMs so enable the kernel support for it
on these systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch registers all the available power domains on ORIGEN board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since the DC5V line is connected directly to the HDMI connector,
"hdmi-en" regulator would become a dummy regulator on origen board
(by defining REGULATOR_DUMMY in the kernel config file).
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a pinmux node to tegra20.dtsi in order to instantiate the future
pinmux device.
v2: Specify reg property precisely; don't just point at the whole APB_MISC
register range.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra GPIO driver will be converted from static registration via
postcore_initcall() to be a platform device later in this patch series.
A new Tegra pinmux platform device will also be added.
Prepare for this by modifying all boards to register the appropriate
platform devices before-hand, so that when the drivers are converted,
those devices will be probed, and git bisectability will be maintained.
v2: Add resource definitions for GPIO and pinmux
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
ARM: mach-ux500: enable fix for ARM errata 754322
ARM: OMAP: musb: Remove a redundant omap4430_phy_init call in usb_musb_init
ARM: OMAP: Fix i2c init for twl4030
ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1
This fixes a compilation error in cpu-tegra.c which was introduced in
dc8d966bcc ("ARM: convert PCI defines to variables") which removed the
now obsolete mach/hardware.h from the mach-tegra subtree.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Activate watchdog, rtc, usb, usb-gadget, keypad, audio for broader test
coverage. Disable remote controls. Activate ARM errata as mentioned in [1].
Rest of changes is caused by version bump to 3.1-rc9.
[1] http://www.spinics.net/lists/arm-kernel/msg88710.html
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This tries to clear up the confusion between integers and iomem pointers
in the marvell pxa platform. MMIO addresses are supposed to be __iomem*
values, in order to let the Linux type checking work correctly. This
patch moves the cast to __iomem as far back as possible, to the place
where the MMIO virtual address windows are defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The sharpsl code selects the max1111 spi driver, so it must also
ensure that SPI itself is enabled. The platform does not work
without max1111.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The two platforms are part of the palm27x family and use the same
code. Select the palm27x symbol to make sure they can be built
standalone.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The raumfeld platform code calls power_supply_set_battery_charged
which is part of the power supply layer, so that always has
to be enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
We cannot support ARMv5 and ARMv7 based boards in a single kernel,
so introduce a new option in mach-pxa to select between the two.
The PJ4 (ARMv7) based boards are now only visible when
CONFIG_ARCH_PXA_V7 is set, the other boards are only visible
when it's not set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The pxa specific cpufreq code is based on the cpu_freq_table
module, so we have to select that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
saarb uses pxa3xx_map_io and pxa3xx_handle_irq, which are part
of the pxa3xx code. This makes sure the necessary header and
implementation is used when building the board file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
There are two variants of the palmtreo machine, the 680 and the
centro, and Kconfig allows selecting one or both of them.
This changes the board file so that it's actually possible
to build all configurations that are allowed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The pxa3xx_u2d_start_hc/pxa3xx_u2d_stop_hc symbols are used by the
ohci-pxa27x driver, which can be a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
When support for zylonite is disabled, the zylonite_pxa300_init
and zylonite_pxa320_init functions are not there, but the declaration
is still kept around if any other boards for the same soc are
enabled. This changes the declaration to be conditional on the
same symbol as the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ARMv6 cores do not implement the DBGOSLAR register, so we don't need to
try and clear it on boot. Furthermore, the VCR is zeroed out of reset,
so we don't need to zero it explicitly when a CPU comes online.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* pm-domains:
PM / Domains: Split device PM domain data into base and need_restore
ARM: mach-shmobile: sh7372 sleep warning fixes
ARM: mach-shmobile: sh7372 A3SM support
ARM: mach-shmobile: sh7372 generic suspend/resume support
PM / Domains: Preliminary support for devices with power.irq_safe set
PM: Move clock-related definitions and headers to separate file
PM / Domains: Use power.sybsys_data to reduce overhead
PM: Reference counting of power.subsys_data
PM: Introduce struct pm_subsys_data
ARM / shmobile: Make A3RV be a subdomain of A4LC on SH7372
PM / Domains: Rename argument of pm_genpd_add_subdomain()
PM / Domains: Rename GPD_STATE_WAIT_PARENT to GPD_STATE_WAIT_MASTER
PM / Domains: Allow generic PM domains to have multiple masters
PM / Domains: Add "wait for parent" status for generic PM domains
PM / Domains: Make pm_genpd_poweron() always survive parent removal
PM / Domains: Do not take parent locks to modify subdomain counters
PM / Domains: Implement subdomain counters as atomic fields
This helps resolve the conflicts between the imx cleanups and the
new code that has gone into the imx tree.
Conflict resolution was originally done by Sascha Hauer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Defconfig file for at91sam9g45 SoC family:
at91sam9g45, at91sam9g46, at91sam9m10, at91sam9m11.
The Atmel Evaluation Kit for this family is the at91sam9m10g45ek.
It is so useful for automatic compile tests...
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This applies ARM errata fix 754322 for all ux500 platforms.
Cc: stable@kernel.org
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's no file named "drivers/char/bcmring/Kconfig". It seems it has
never been part of the mainline kernel tree. So there's nothing to be
sourced here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With LPAE, the physical address mask is 40-bit while the page table
entry is 64-bit. This patch introduces PHYS_MASK for the 2-level page
table format, defined as ~0UL.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch defines the (pte|pmd)val_t as u32 and changes the page table
types to be based on these. The PMD bits are converted to the
corresponding type using the _AT macro.
The flush_pmd_entry/clean_pmd_entry argument was changed to (void *) to
allow them to be used with both PGD and PMD pointers and avoid code
duplication.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves page table definitions from asm/page.h, asm/pgtable.h
and asm/ptgable-hwdef.h into corresponding *-2level* files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up the Samsung resources in plat-samsung/devs.c
by using defined helpers at <linux/ioport.h>.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch merges each dev files to one devs.c file in
plat-samsung directory and this help to keep it more
easily to reduce plat- directories such as plat-s3c24xx
and plat-s5p.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves regarding s5p dev files to one devs.c file
in plat-samsung directory and this help to keep it more
easily.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves regarding s3c64xx dev files to one devs.c
file in plat-samsung directory and this help to keep it more
easily.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves regarding s3c24xx dev files to one devs.c
file in plat-samsung directory and this is required to merge
to plat-samsung.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add nodes for devices used by PM code (mpu, dsp, iva).
Add a cpus node as well as recommended in the DT spec.
Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>
Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add device-tree support for the l3-noc driver.
Use platform_driver_register to defer the probing at device init
time.
Add documentation for the l3-noc bindings.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Still needed to boot until the i2c & twl driver is adapted to
device-tree. Otherwise the voltage control code will try to
access the twl and crash.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Re-cycle the original board-generic.c file to support Device Tree
for every OMAP2+ variants.
The current approach is an intermediate step before having only
one machine descriptor that will use some generic DT aware
functions.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Add OMAP3 beagleboard DTS file to use the omap3.dtsi SoC file.
Add a default bootargs line to allow a boot from RAMDISK.
Add memory node information.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Add the SDP/Blaze (Software Development Board) support with
device tree.
That file is based on the omap4-panda.dts.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Based on the original omap4-panda.dts file from Manju.
http://www.spinics.net/lists/linux-omap/msg55836.html
Add memory information and a default bootargs to allow
a boot from RAMDISK.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Add initial device-tree support for OMAP4 SoC.
This is based on the original panda board patch done by Manju:
http://permalink.gmane.org/gmane.linux.ports.arm.omap/60393
Add the generic GIC interrupt-controller from ARM.
Add an empty "soc" node to contain non memory mapped IPs
(DSP, MPU, IPU...).
Note: Since reg, irq and dma are provided by hwmod for the
moment, these attributes will not be present at all in DTS
to highlight the gap. They will be added as soon as dma bindings
will be there and drivers will be adapted.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Nicolas Pitre's vmalloc cleanup series didn't get merged in this cycle
so picoxcell is missing a VMALLOC_END definition.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Awhile back I removed all the CONFIG_GENERIC_TIME referecnes as
the last of the non-GENERIC_TIME arches were converted.
However, due to the functionality being important and around for
awhile, there apparently were some out of tree hardware enablement
patches that used it and have since been merged.
This patch removes the remaining instances of GENERIC_TIME.
Singed-off-by: John Stultz <john.stultz@linaro.org>
Add a notifier called during device_add phase. If an of_node is present,
retrieve the hwmod entry in order to populate properly the omap_device
structure.
For the moment the resource from the device-tree are overloaded.
DT does not support named resource yet, and thus, most driver will not
work without that information.
Add a documentation to capture the specifics OMAP bindings needed for
device-tree support.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Split the omap_device_build_ss into two smaller functions
that will allow to populate a platform_device already allocated by
device-tree.
The functionality of the omap_device_build_ss is still the same, but
the omap_device_alloc will be usable with devices already built by
device-tree.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove all these duplicated structures since a default one is now
available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Most devices are using the same default omap_device_pm_latency structure
during device built. In order to avoid the duplication of the same
structure everywhere, add a default structure that will be used if
the device does not have an explicit one.
Next patches will clean the duplicated structures.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since the device pointer is now retrieved using the hwmod name, remove
the static variables used to store the device pointers for DSP, MPU, IVA
and L3 devices for PM/DVFS usage.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Replace the struct device parameter of omap2_set_init_voltage
by the hwmod name. It will avoid having to store explicitely
the device pointer into a static variable.
Moreover, it will be a little bit more scalable if we introduce
new DVFS devices.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Replace the multiple omap2_get_XXX_device APIs with the new
omap_hwmod_name_get_dev that uses the hwmod name to get the proper
device.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
An API which translates a standard hwmod name to corresponding
platform_device is useful for drivers when they need to look up the
device associated with a hwmod name to map back into the device
structure pointers. These ideally should be used by drivers in
mach directory. Using a generic hwmod name like "gpu" instead of
the actual device name which could change in the future, allows
us to:
a) Could in effect help replace apis such as omap2_get_mpuss_device,
omap2_get_iva_device, omap2_get_l3_device, omap4_get_dsp_device,
etc..
b) Scale to more devices rather than be restricted to named functions
c) Simplify driver's platform_data from passing additional fields
all doing the same thing with different function pointer names
just for accessing a different device name.
Signed-off-by: Nishanth Menon <nm@ti.com>
[b-cousson@ti.com: Adapt it to the new pdev pointer inside od,
remove the unneeded helpers, and fold the next patch here]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The sleep code for S5PV210 and EXYNOS4 are identical; moreover
S5p64X0 and S5PC100 for which support will be added soon can
use the same procedure. Create a common sleep code in the plat-s5p
directory so that it can be re-used.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pave the way for adding PM support on S5P64X0, which is more similar
to the S3C64XX series than the S5P series. Hence, the common pm code
(containing dummy functions) should not be used for S5P64X0.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves header files from plat-s5p to plat-samsung to
remove plat-s5p directory to make one plat-samsung directory
for Samsung SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves header files from plat-s3c24xx to plat-samsung to
remove plat-s3c24xx directory to make one plat-samsung directory for
Samsung SoCs. And this patch includes fixing coding style, too.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves SoC header files for supporting each SoCs to
plat-samsung directory. This is required to make one plat-
directory for Samsung SoCs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commit a3831cf ("ARM: Consolidate the
clkdev header files"), current mach/clkdev.h is no
needed in Samsung stuff.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sdhci platform helper function that sets up the default controller
configuration is removed for all Samsung platforms since such default
controller configuration can be handled by the driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definitions to enable support for s5p-fimc driver on
SMDKV310 board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support usb ehci device to the SMDKV310 board.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2416/S3C2450 use the same clocks for their i2s blocks
and can therefore reuse the existing ones.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch:
-- Adds platform device support for LCD-LTE480.
-- Adds platform data for FB with win_mode and default_bpp.
-- Enables FB device support and platform-lcd support.
-- Adds SPCON settings for LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch:
-- Adds platform device support for LCD-LTE480.
-- Adds platform data for FB with win_mode and default_bpp.
-- Enables FB device support and platform-lcd support.
-- Adds SPCON settings for LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds GPIO lines settings(HSYNC, VSYNC, VCLK and VD) for LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Set s3c_device_fb name as "s5p64x0-fb" for S5P6440 and S5P6450.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds:
-- Framebuffer related register mappings and bit fields.
-- IRQ number being used.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modifies PMU register setting function
to support the other EXYNOS4 SoCs.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add voltage regulator definitions for M-5MOLS camera, platform data
definition for the sensor and MIPI-CSI receiver drivers.
Add CAM power domain dependencies for FIMC and CSIS devices.
Define required I2C0 bus timings. Setup camera port A GPIO.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add platform data for CIF camera sensor and FIMC platform data
entries for it. Add platform device for s5p-fimc media device
driver and the camera port A I/O pins initialization.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform devices and regulators for TV devices on
Samsung Goni board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform devices and regulators for TV devices on
Samsung Universal C210 board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds all the resources for TV drivers and devices for Samsung
Exynos4 and S5PV210 platforms.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[m.szyprowski: squashed Exynos4 and S5PV210 patches and rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds hdmiphy dedicated i2c controller definitions.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[m.szyprowski: renamed to i2c-hdmiphy and squashed Exynos4 and S5PV210 patches]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
SMDK4412 board is same as a SMDK4212 board except that
it has EXYNOS4412 SoC, thus it can share machine code
with SMDK4212.
This patch renames mach-smdk4212.c to mach-smdk4x12.c
to support both SMDK4212 and SMDK4412 board with one
machine file.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Current MCT implementation only provide 2 event timers,
thus cannot support EXYNOS4412 which has 4 CPU cores.
This patch fixes MCT implementation to support SoCs
with 4 cores.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds two functions for gic interrupt handling.
1. Add interrupt handling of 4 cores.
2. Dynamically set gic bank offset according to the type of soc.
Gic bank offset of EXYNOS4412 is 0x4000 while the offset of
EXYNOS4210 and EXYNOS4212 is 0x8000.
This patch is necessary because EXYNOS4 socs cannot support
GIC register banking as described in commit aab74d3e75.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch makes EXYNOS4412 use same clock code for
EXYNOS4212 because the clock hierarchy of both SoCs
are same.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung EXYNOS4412 SoC support.
The EXYNOS4412 integrates a ARM Cortex A9 quad-core.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch implements clock event timer using MCT PPI
and make EXYNOS4212 use MCT PPI instead of MCT SPI.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To support PPI in external GIC of EXYNOS4 SoCs,
gic_arch_extn.irq_eoi, irq_unmask and irq_mask are
fixed. This patch is necessary because external GIC of EXYNOS4
cannot support register banking.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Based on "ARM: introduce atag_offset to replace boot_params"
by Nicolas Pitre (2bb9839e31).
Since boot_params variable is deleted from machine_desc, the variable
is modified in the newer board files.
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
[kgene.kim@samsung.com: added fixing for smdkv310]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds an ioremap hook imx_ioremap to be called in
__imx_ioremap(). Any soc that needs a customized ioremap other
than __arm_ioremap() can set up this hook in soc specific call.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds an idle hook imx_idle to be called in arch_idle().
Any soc that needs a customized idle implementation other than
cpu_do_idle() can set up this hook in soc specific call.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Consolidate mm-mx23.c and mm-mx28.c into a single file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch update config file of NURI board to enable RTC
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform definitions to enable s3c-fb driver.
Framebuffer window with 1280x800x16bpp mode has been defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds platform definitions to enable s3c-fb driver.
Framebuffer window with 480x800x16bpp mode has been defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds hot plug detection(HPD) and power domain(PD)
support for HDMI on ORIGEN board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ORIGEN board is fitted with 7" LCD panel HV070WSA. The pixel
resolution of the LCD panel is 1024x600.
Also power domain device for LCD0 is registered.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
