System restart mechanism has been changed with the introduction
of "kernel restart handler call chain support". The imx2 watchdog
based restart handler has been moved to the driver, and these
restart can be removed from the machine layer.
This patch cleans up the device tree version machine reset init with
mxc_arch_reset_init_dt and removes corresponding .restart handler,
for the .init_machine that can be handled by system default after
removing the mxc_arch_reset_init_dt, the .init_machine is also removed.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds a reset fallback if base address of watchdog is not set.
This is intended for a targets not compatible with imx-21 watchdog,
i.MX1 for example.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch simplifies handling watchdog clock a bit.
As an additional change, now we properly check WDT clock in a reset
function.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Now that we handle this in core code, we don't need platforms enabling
the low power modes directly.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have a mixture of different devices with different register layouts,
but we group all the bits together in an opaque mess. Split them out
into those which are L2C-310 specific and ones which refer to earlier
devices. Provide full auxiliary control register definitions.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
They're u32, they're not unsigned long. The UL suffix is not required
here.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current comment in the code does not make it clear why the double writes
on SRC bit is needed. Let's quote the errata to get it clear. Also, to
ensure there are at least 2 writes happen in the same one 32kHz period,
we actually need 3 writes. Let's add the third one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is ~10% possibility that the following emergency restart command
fails to reboot imx6q.
$ echo b > /proc/sysrq-trigger
The IMX restart routine mxc_restart() assumes that it will always run on
primary core, and will call imx_src_prepare_restart() to disable
secondary cores in order to get them come to online in the following
boot. However, the assumption is only true for normal kernel_restart()
case where migrate_to_reboot_cpu() will be called to migrate to primary
core, but not necessarily true for emergency_restart() case. So when
emergency_restart() calls into mxc_restart() on any secondary core,
system will hang immediately once imx_src_prepare_restart() is called
to disabled secondary cores. Since emergency_restart() is defined as a
function that is safe to call in interrupt context, we cannot just call
migrate_to_reboot_cpu() to fix the issue.
Fortunately, we just found that the issue can be fixed at imx6q platform
level. We used to call imx_src_prepare_restart() to disable all
secondary cores before resetting hardware. Otherwise, the secondary
will fail come to online in the reboot. However, we recently found that
after commit 6050d18 (ARM: imx: reset core along with enable/disable
operation) comes to play, we do not need to reset the secondary cores
any more. That said, mxc_restart() now can run on any core to reboot
the system, as long as we remove the imx_src_prepare_restart() call from
mxc_restart().
So let's simply remove imx_src_prepare_restart() call to fix the above
emergency restart failure.
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q_restart() works fine with normal reboot but will run into
problem with emergency reboot like sysrq-b. In that case, of_iomap()
gets called from interrupt context and hence triggers the BUG_ON in
__get_vm_area_node().
Actually, since commit c1e31d1 (ARM: imx: create
mxc_arch_reset_init_dt() for DT boot), imx6q/dl should try to use
mxc_restart() by calling mxc_arch_reset_init_dt() beforehand, where
things like of_iomap() can be done.
The patch updates mxc_restart() a little bit to get it work for imx6q/dl
and kill imx6q_restart() completely.
Reported-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
But according to ARM PL310 errata: 752271
ID: 752271: Double linefill feature can cause data corruption
Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
Workaround: The only workaround to this erratum is to disable the
double linefill feature. This is the default behavior.
without this patch, you will meet the following error when run the
memtester application at: http://pyropus.ca/software/memtester/
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365664.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365668.
FAILURE: 0x00100000 != 0x00200000 at offset 0x0136566c.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365670.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365674.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365678.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This fixes the following compilation error:
arch/arm/mach-imx/system.c:101:123: error: static declaration of ‘imx_init_l2cache’ follows non-static declaration
In file included from arch/arm/mach-imx/system.c:32:0:
arch/arm/mach-imx/common.h:165:13: note: previous declaration of ‘imx_init_l2cache’ was here
arch/arm/mach-imx/system.c:101:123: warning: ‘imx_init_l2cache’ defined but not used [-Wunused-function]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Move imx6q L2 initialization function imx6q_init_l2cache() into
system.c, and rename it imx_init_l2cache(), so that other platforms
other than imx6q can also use the function.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mxc_arch_reset_init() uses static mapping and calls clk_get_sys() to
get clock. It's suitable for non-DT boot but not for DT boot where
dynamic mapping and of_clk_get() should be used instead. Create
mxc_arch_reset_init_dt() as the DT variant of mxc_arch_reset_init(),
and change DT platforms to use it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's inappropriate to call clk_prepare() in mxc_restart(), because the
restart routine could be called in atomic context. Move clk_get() and
clk_prepare() into mxc_arch_reset_init() and only have the atomic part
clk_enable() be called in mxc_restart().
As a result, mxc_arch_reset_init() needs to be called after clk gets
initialized.
While there, it also changes printk(KERN_ERR ...) to pr_err() and adds
__init annotation for mxc_arch_reset_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It moves a bunch of header files included in hardware.h and itself
from mach-imx/include/mach to mach-imx, and updates users to include
hardware.h rather than mach/hardware.h. The files in mach-imx/devices
will need to include "../hardware.h".
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/common.h to mach-imx/common.h and update
all users to include common.h rather than mach/common.h.
It also removes an unneeded inclusion to common.h in
mach-imx/devices/devices.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It's really unnecessary to have plat-mxc, and let's merge it into
mach-imx. It's pretty much just a bunch of file renaming and
Kconfig/Makefile merge.
To make the change less invasive, we keep using Kconfig symbol
CONFIG_ARCH_MXC for mach-imx sub-architecture.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
