While the ycbcr_enc field doesn't apply to raw formats, leaving it
uninitialized makes the driver behave in a less deterministic way. Fix
it by picking the default value for the colorspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The imx219_set_binning() function sets registers based on the bpp value,
which is computed in imx219_set_framefmt(). As both functions are called
from the same place consecutively, and set registers based on the
selected mode, merge them together to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Replace the per-mode register arrays with code that sets the same
register values using the mode definitions. This avoids duplicating
information in two different places.
The error check for invalid formats in imx219_set_framefmt() is dropped
as the format is guaranteed to be valid.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The 640x480 mode specifies incorrect values for the TP_WINDOW_WIDTH and
TP_WINDOW_HEIGHT registers, which likely got copied from the 1640x1232
mode. They should be identical to the X_OUTPUT_SIZE and Y_OUTPUT_SIZE
registers as for all the other modes, to avoid cropping the test
pattern. Fix them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The IMX219_REG_CSI_LANE_MODE is configured twice, once with a hardcoded
value in the imx219_common_regs registers array, and once with the value
appropriate for the system in imx219_configure_lanes(). The latter is
enough, drop the former.
Fixes: ceddfd4493 ("media: i2c: imx219: Support four-lane operation")
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Define macros for all the known registers used in the register arrays,
and use them to replace the numerical addresses. This improves
readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop a handful of macros that are not used and don't provide any value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the new common CCI register access helpers to replace the private
register access helpers in the imx219 driver. This simplifies the driver
by reducing the amount of code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The MT9M114 is a CMOS camera sensor that combines a 1296x976 pixel array
with a 10-bit dynamic range together with an internal ISP. The driver
exposes two subdevs, one for the pixel array and one for the ISP (named
IFP for Image Flow Processor). Major supported features are
- Full configuration of analog crop and binning in the pixel array
- Full configuration of scaling in the ISP
- Automatic exposure and white balance
- Manual exposure and analog gain
- Horizontal and vertical flip
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a new mode - 16:9 resolution 1296x722 for hi556.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop of_match_ptr() from tvp514x_driver and get rid of ugly CONFIG_OF
if check. This slightly increases the size of tvp514x_driver on non-OF
system and shouldn't be an issue.
Add mod_devicetable.h include.
It also allows, in case if needed, to enumerate this device via ACPI with
PRP0001 magic.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver has an OF match table, still, it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using i2c_get_match_data() if the devices are registered via OF/ID.
Unify the OF/ID table by using tvp514x_reg as match data for both
these tables and replace the ID lookup table for the match data by
i2c_get_match_data() and simplifly probe().
While at it, remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop of_match_ptr() from adv7180_driver and get rid of ugly CONFIG_OF
if check. This slightly increases the size of adv7180_driver on non-OF
system and shouldn't be an issue.
Add mod_devicetable.h include.
It also allows, in case if needed, to enumerate this device via ACPI with
PRP0001 magic.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver has an OF match table, still, it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using i2c_get_match_data() if the devices are registered via OF/ID.
Unify the OF/ID table by using struct adv7180_chip_info as match data for
both these tables and replace the ID lookup table for the match data by
i2c_get_match_data().
While at it, remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Don't rely on a define, let the compiler use the actual
field size.
Remove all uses of the V4L2_SUBDEV_NAME_SIZE define and also
drop the define itself.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Instead of creating a huge switch statement (that thoroughly confuses
smatch), create a table of coefficients and use that.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The sensor is guaranteed not to be streaming when the runtime PM resume
handler is called, as the resume handler is only called from the
.s_stream() operation when starting streaming. Similarly, the sensor has
been stopped when the runtime PM suspend handler is called. There is
thus no need for manual stream start/stop from the runtime PM handlers.
Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
Now that the runtime PM operations are not called from the system PM
handlers, the sensor is guaranteed not to be streaming when the runtime
PM resume handler is called, and to have been stopped already when the
runtime PM suspend handler is called. Drop the manual stream start/stop
from the runtime PM handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mikhail Rudenko <mike.rudenko@gmail.com>
[Sakari Ailus: remove now-redundant "streaming" from comment.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This commit adds support for:
- 1364x768 at 120 FPS
Signed-off-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The streaming flag in the driver private structure is used for the sole
purpose of gating register writes when setting a V4L2 control. This is
better handled by checking if the sensor is powered up using the runtime
PM API. Do so and drop the streaming flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The streaming flag in the driver private structure is used for the sole
purpose of gating register writes when setting a V4L2 control. This is
better handled by checking if the sensor is powered up using the runtime
PM API. Do so and drop the streaming flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Sakari Ailus: Runtime PM put when setting analgue gain.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The streaming flag in the driver's private structure is set but never
used. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Simplify error handling by using pm_runtime_resume_and_get() instead of
pm_runtime_get_sync() with a put call in the error path.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> (st-vgxy61)
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add support for the imx334's test pattern generator.
By default the test pattern generator is disabled, so add support for
enabling and disabling horizontal and vertical colour bars.
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop of_match_ptr() from ov7670_driver and get rid of ugly CONFIG_OF
if check. This slightly increases the size of ov7670_driver on non-OF
system and shouldn't be an issue.
Add mod_devicetable.h include.
It also allows, in case if needed, to enumerate this device via ACPI with
PRP0001 magic.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver has an OF match table, still, it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using i2c_get_match_data() if the devices are registered via OF/ID.
Unify the OF/ID table by using struct ov7670_devtype as match data for
both these tables and replace the ID lookup table for the match data by
i2c_get_match_data().
Split the array ov7670_devdata[] as individual variables, and
make lines shorter by referring to e.g. &ov7670_devdata instead of
&ov7670_devdata[MODEL_OV7670].
Drop enum ov7670_model as there is no user.
While at it, remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop of_match_ptr() from mt9v032_driver and get rid of ugly CONFIG_OF
if check. This slightly increases the size of mt9v032_driver on non-OF
system and shouldn't be an issue.
Add mod_devicetable.h include.
It also allows, in case if needed, to enumerate this device via ACPI with
PRP0001 magic.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver has an OF match table, still, it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using i2c_get_match_data() if the devices are registered via OF/ID.
Unify the OF/ID table by using mt9v032_model_info as match data for both
these tables and replace the ID lookup table for the match data by
i2c_get_match_data() and simplifly probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 7d3c7d2a29 ("media: i2c: Add a camera sensor top level
menu") the CONFIG_MEDIA_CONTROLLER and CONFIG_VIDEO_V4L2_SUBDEV_API are
selected by the top-level VIDEO_CAMERA_SENSOR menu.
Remove all ifdefferies from camera sensor drivers to simplify the code.
Compile-tested only.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *video_i2c_chip for data in the match table. Simplify
the probe() by replacing device_get_match_data() and ID lookup for
retrieving data by i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The imx415 driver uses the subdev active state, there's
no need to implement the .get_fmt() operation manually. Use
the v4l2_subdev_get_fmt() helper instead.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This is odd to have a of_node_put() just after a for_each_child_of_node()
or a for_each_endpoint_of_node() loop. It should already be called
during the last iteration.
Remove these calls.
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With devm_clk_get_enabled() the call to clk_disable_unprepare() can be
dropped from the error path and the remove callback.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The value of V4L2_CID_VBLANK control is initialized to default vblank
value of 640x480 when driver probe. When OV5640 work at DVP mode, the
control value won't update and lead to sensor can't output data if the
resolution remain the same as last time since incorrect total vertical
size. So update it when there is a new value applied.
Fixes: bce93b827d ("media: ov5640: Add VBLANK control")
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The "ret = " assignment was missing, so ov13b10_power_on() is not
checked for errors. Add the assignment.
Fixes: 6e28afd152 ("media: ov13b10: add PM control support based on power resources")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The commit in Fixes has removed an fwnode_handle_put() call in the error
handling path of the probe.
Remove the same call from the remove function.
Fixes: 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The .set_fmt() handler tries to avoid updating the sensor configuration
when the mode hasn't changed. It does so by comparing both the mode and
the media bus code. While the latter correctly uses the media bus code
stored in the subdev state, the former compares the mode being set with
the active mode, regardless of whether .set_fmt() is called for the
ACTIVE or TRY format. This can lead to .set_fmt() returning early when
operating on TRY formats.
This could be fixed by replacing the mode comparison with width and
height comparisons, using the frame size stored in the subdev state.
However, the optimization that avoids updates to the sensor
configuration is not very useful, and is not commonly found in sensor
drivers. To improve consistency across sensor drivers, it is better, in
addition to being easier, to simply drop it. Do so.
Fixes: e8a5b1df00 ("media: i2c: imx219: Use subdev active state")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When moving the imx219 driver to the subdev active state, commit
e8a5b1df00 ("media: i2c: imx219: Use subdev active state") used the
pad crop rectangle stored in the subdev state to report the crop
rectangle of the active mode. That crop rectangle was however not set in
the state when setting the format, which resulted in reporting an
incorrect crop rectangle to userspace. Fix it.
Fixes: e8a5b1df00 ("media: i2c: imx219: Use subdev active state")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The imx219_init_cfg() function has stopped operating on the try format
since commit 7e700847b1 ("media: i2c: imx219: Switch from open to
init_cfg"), but a comment in the function wasn't updated. Fix it.
While at it, improve spelling in a second comment in the function.
Fixes: 7e700847b1 ("media: i2c: imx219: Switch from open to init_cfg")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The commit in Fixes has removed an fwnode_handle_put() call in the error
handling path of max9286_v4l2_register().
Remove the same call from max9286_v4l2_unregister().
Fixes: 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix the following smatch warning:
drivers/media/i2c/rdacm21.c:373 ov10640_check_id() error: uninitialized
symbol 'val'.
Initialize 'val' to 0 in the ov10640_check_id() function.
Fixes: 2b821698dc ("media: i2c: rdacm21: Power up OV10640 before OV490")
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix the following smatch warning:
drivers/media/i2c/ccs/ccs-data.c:524 ccs_data_parse_rules() warn: address
of NULL pointer 'rules'
The CCS static data rule parser does not check an if rule has been
obtained before checking for other rule types (which depend on the if
rule). In practice this means parsing invalid CCS static data could lead
to dereferencing a NULL pointer.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Cc: stable@vger.kernel.org # for 5.11 and up
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
smatch reports:
drivers/media/i2c/ds90ub960.c:1788 ub960_init_tx_ports() error: uninitialized symbol 'pll_div'.
This is caused by 'pll_div' not being set for 1200 MHz CSI rate. Set the
'pll_div' correctly.
Closes: https://lore.kernel.org/all/8d6daeb1-b62a-bbb2-b840-8759c84f2085@xs4all.nl/
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
smatch reports some uninitialized variables:
drivers/media/i2c/ds90ub953.c:655 ub953_log_status() error: uninitialized symbol 'gpio_local_data'.
drivers/media/i2c/ds90ub953.c:655 ub953_log_status() error: uninitialized symbol 'gpio_input_ctrl'.
drivers/media/i2c/ds90ub953.c:655 ub953_log_status() error: uninitialized symbol 'gpio_pin_sts'.
These are used only for printing debug information, and the use of an
uninitialized variable only happens if an i2c transaction has failed,
which will print an error. Thus, fix the errors just by initializing the
variables to 0.
Closes: https://lore.kernel.org/all/8d6daeb1-b62a-bbb2-b840-8759c84f2085@xs4all.nl/
Fixes: 6363db1c9d ("media: i2c: add DS90UB953 driver")
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
smatch reports some uninitialized variables:
drivers/media/i2c/ds90ub913.c:481 ub913_log_status() error: uninitialized symbol 'v1'.
drivers/media/i2c/ds90ub913.c:481 ub913_log_status() error: uninitialized symbol 'v2'.
These are used only for printing debug information, and the use of an
uninitialized variable only happens if an i2c transaction has failed,
which will print an error. Thus, fix the errors just by initializing the
variables to 0.
Closes: https://lore.kernel.org/all/8d6daeb1-b62a-bbb2-b840-8759c84f2085@xs4all.nl/
Fixes: c158d0d4ff ("media: i2c: add DS90UB913 driver")
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Verify that the number of CSI lanes and link-frequency specified
in the endpoint fwnode are correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add read-only link-freq and pixel-rate controls. This is necessary for
the sensor to work with the ipu3-cio2 driver and for libcamera.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Read and log sensor revision during probe.
Since this means that the driver will now already log a message on
successful probe drop the "ov2680 init correctly" log message.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Drop unnecessary pad checks in enum_mbus_code, get_fmt, set_fmt
this is already checked by check_pad() from
drivers/media/v4l2-core/v4l2-subdev.c.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Usually when developing a sensor driver with help from the vendor
the vendor will provide a bunch of register tweaks for optimal
performance of the sensor.
The atomisp-ov2680.c driver was (presumably) developed by Intel with
help from OmniVision and indeed contains a bunch of register tweaks.
Add these register tweaks to the "main" ov2680.c driver.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The exposure control's max effective value is VTS - 8, set the control
range to match this. Thas means that if/when a future commit makes VTS
configurable as a control itself the exposure range needs to be
updated dynamically to match the VTS value.
The gain control goes from 0 - 1023, higher values wrap around to
the lowest gain setting.
The gain control, controls an analog gain so use V4L2_CID_ANALOGUE_GAIN
for it instead of V4L2_CID_GAIN.
Also stop setting 0 as default for both controls this leads to
a totally black picture which is no good. This is esp. important
for tests of the sensor driver without (userspace driven)
auto exposure / gain.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement selection support. Modelled after ov5693 selection support,
but allow setting sizes smaller than crop-size through set_fmt() since
that was already allowed.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add an __ov2680_get_pad_format() helper function.
This is a preparation patch for adding selections support.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Instead of using a long fixed register settings list for each resolution,
calculate the register settings based on the requested width + height.
This is based on atomisp-ov2680 commit 0611888592 ("media: atomisp:
ov2680: Make setting the modes algorithm based").
This will allow future enhancements like adding hblank and vblank controls
and adding selection support.
This also adds properly programming the ISP window and setting
the manual ISP window control bit in register 0x5708, this is
necessary for the hflip and vflip conrols to work properly.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add an ov2680_mode struct to group together mode related state.
For now this only contains the v4l2_mbus_framefmt and
the frame_interval.
This is a preparation patch for moving to calculating the per mode
settings, which will store more info in the new ov2680_mode struct.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Annotate the per mode register setting lists.
This is a preparation patch for moving to calculating the per mode
settings, allowing to set any mode through cropping.
The annotations make it easier to see which registers are mode
dependent and which are fixed.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix and simplify ov2680_enum_frame_interval(), the index is not
an index into ov2680_mode_data[], so using OV2680_MODE_MAX is wrong.
Instead it is an index indexing the different framerates for
the resolution specified in fie->width, fie->height.
Note validating fie->which is not necessary this is already done
by the v4l2-core.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add an acpi_match_table now that all the other bits necessary for
ACPI support are in place.
The OVTI prefix used for the ACPI-HID is used for various OmniVision
sensors on many generations x86 tablets and laptops.
The OVTI2680 HID specifically is used on multiple models spanning at
least 4 different Intel CPU models (2 ISP2, 2 IPU3).
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Defer probe() until the endpoint fwnode is available. This is necessary
on ACPI platforms where the bridge code creating the fwnodes may also e.g.
set the "clock-frequency" device property and add GPIO mappings.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most x86/ACPI boards use the ov2680 with a 19.2 MHz xvclk,
rather then the expected 24MHz, add support for this.
Compensate for the lower clk by setting a higher PLL multiplier
of 69 when using 19.2 MHz vs the default multiplier of 55 for
a 24MHz xvclk.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On ACPI systems the following 2 scenarios are possible:
1. The xvclk is fully controlled by ACPI powermanagement, so there
is no "xvclk" for the driver to get (since it is abstracted away).
In this case there will be a "clock-frequency" device property
to tell the driver the xvclk rate.
2. There is a xvclk modelled in the clk framework for the driver,
but the clk-generator may not be set to the right frequency
yet. In this case there will also be a "clock-frequency" device
property and the driver is expected to set the rate of the xvclk
through this frequency through the clk framework.
Handle both these scenarios by switching to devm_clk_get_optional()
and checking for a "clock-frequency" device property.
This is modelled after how the same issue was fixed for the ov8865 in
commit 73dcffeb2f ("media: i2c: Support 19.2MHz input clock in ov8865").
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
With runtime-pm it is guaranteed that ov2680_power_on() and
ov2680_power_off() will always be called in a balanced way;
and the is_enabled check in ov2680_s_ctrl() can be replaced
by checking the runtime-suspend state.
So there is no more need for the is_enabled flag, remove it.
While at it also make sure that flip control changes while
suspended still lead to the bayer-order getting updated so
that get_fmt returns the correct bayer-order.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The datasheet of the OV2680 labels the single GPIO to put the sensor in
powersaving mode as XSHUTDN aka shutdown, _not_ reset.
This is important because some boards have standardized sensor connectors
which allow connecting various sensor modules. These connectors have both
reset and powerdown signals and the powerdown signal is routed to
the OV2680's XSHUTDN pin.
On x86/ACPI multiple Bay Trail, Cherry Trail, Sky Lake and Kaby Lake models
have an OV2680 connected to the ISP2 / IPU3. On these devices the GPIOS are
not described in DT instead the GPIOs are described with an Intel specific
DSM which labels them as either powerdown or reset. Often this DSM returns
both reset and powerdown pins even though the OV2680 has only 1 such pin.
For the ov2680 driver to work on these devices it must use the GPIO with
"powerdown" as con-id, matching the XSHUTDN name from the datasheet.
As for why "powerdown" vs say "shutdown" the ACPI DSM -> con-id mapping
code is shared, so we must use standardized names and currently all of
the following sensor drivers already use "powerdown":
adv7180, gc0310, isl7998x, ov02a10, ov2659, ov5640, ov5648, ov5670,
ov5693, ov7670, ov772x, ov7740, ov8858, ov8865 and ov9650 .
Where as the hi846 driver is the lonely standout using "shutdown".
Try the "powerdown" con-id first to make things work, falling back to
"reset" to keep existing DT setups working.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove the obsolete s_power() callback and instead use runtime-pm +
autosuspend, powering-on the sensor on s_stream(1) and releasing
the runtime-pm reference on s_stream(0).
This also removes the need for ov2680_mode_restore() instead
ov2680_stream_enable() now takes care of all sensor initalization
after power-on.
This is a preparation patch for adding ACPI support.
Note this also removes putting the clock lane into LP-11 state from
ov2680_power_on() since now streaming will start immediately after
powering on the sensor there is no need to put the clock lane
in a low power state.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that the cci_* register access helpers are used access to
the i2c_client after probe() is no longer necessary.
Directly store a struct device *dev pointing to &client->dev inside
ov2680_dev to make the code simpler.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new comon CCI register access helpers to replace the private
register access helpers in the ov2680 driver.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the ov2680_power_on() "sensor soft reset failed" path is hit during
probe() the WARN() about putting an enabled regulator at
drivers/regulator/core.c:2398 triggers 3 times (once for each regulator),
filling dmesg with backtraces.
Fix this by properly disabling the regulators on ov2680_power_on() errors.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ov2680_set_fmt() which == V4L2_SUBDEV_FORMAT_TRY was getting
the try_fmt v4l2_mbus_framefmt struct from the passed in sd_state
and then storing the contents of that into the return by reference
format->format struct.
While the right thing to do would be filling format->format based on
the just looked up mode and then store the results of that in
sd_state->pads[0].try_fmt .
Before the previous change introducing ov2680_fill_format() this
resulted in ov2680_set_fmt() which == V4L2_SUBDEV_FORMAT_TRY always
returning the zero-ed out sd_state->pads[0].try_fmt in format->format
breaking callers using this.
After the introduction of ov2680_fill_format() which at least
initializes sd_state->pads[0].try_fmt properly, format->format
is now always being filled with the default 800x600 mode set by
ov2680_init_cfg() independent of the actual requested mode.
Move the filling of format->format with ov2680_fill_format() to
before the if (which == V4L2_SUBDEV_FORMAT_TRY) and then store
the filled in format->format in sd_state->pads[0].try_fmt to
fix this.
Note this removes the fmt local variable because IMHO having a local
variable which points to a sub-struct of one of the function arguments
just leads to confusion when reading the code.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a ov2680_fill_format() helper function and use this everywhere were
a v4l2_mbus_framefmt struct needs to be filled in so that the driver always
fills it consistently.
This is a preparation patch for fixing ov2680_set_fmt()
which == V4L2_SUBDEV_FORMAT_TRY calls not properly filling in
the passed in v4l2_mbus_framefmt struct.
Note that for ov2680_init_cfg() this now simply always fills
the try_fmt struct of the passed in sd_state. This is correct because
ov2680_init_cfg() is never called with a NULL sd_state so the old
sd_state check is not necessary.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On ov2680_set_fmt() calls with format->which == V4L2_SUBDEV_FORMAT_TRY,
ov2680_set_fmt() does not talk to the sensor.
So in this case there is no need to lock the sensor->lock mutex or
to check that the sensor is streaming.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
VIDEO_V4L2_SUBDEV_API is now automatically selected in Kconfig
for all sensor drivers. Remove the ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
checks.
This is a preparation patch for fixing ov2680_set_fmt()
which == V4L2_SUBDEV_FORMAT_TRY calls not properly filling in
the passed in v4l2_mbus_framefmt struct.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ov2680_vflip_disable() / ov2680_hflip_disable() pass BIT(0) instead of
0 as value to ov2680_mod_reg().
While fixing this also:
1. Stop having separate enable/disable functions for hflip / vflip
2. Move the is_streaming check, which is unique to hflip / vflip
into the ov2680_set_?flip() functions.
for a nice code cleanup.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The index into ov2680_hv_flip_bayer_order[] should be 0-3, but
ov2680_bayer_order() was using 0 + BIT(2) + (BIT(2) << 1) as
max index, while the intention was to use: 0 + 1 + 2 as max index.
Fix the index calculation in ov2680_bayer_order(), while at it
also just use the ctrl values rather then reading them back using
a slow i2c-read transaction.
This also allows making the function void, since there now are
no more i2c-reads to error check.
Note the check for the ctrls being NULL is there to allow
adding an ov2680_fill_format() helper later, which will call
ov2680_set_bayer_order() during probe() before the ctrls are created.
[Sakari Ailus: Change all users of ov2680_set_bayer_order() here]
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Quoting the OV2680 datasheet:
"3.2 exposure and gain control
In the OV2680, the exposure time and gain are set manually from an external
controller. The OV2680 supports manual gain and exposure control only for
normal applications, no auto mode."
And indeed testing with the atomisp_ov2680 fork of ov2680.c has shown that
auto-exposure and auto-gain do not work.
Note that the code setting the auto-exposure flag was broken, callers
of ov2680_exposure_set() were directly passing !!ctrls->auto_exp->val as
"bool auto_exp" value, but ctrls->auto_exp is a menu control with:
enum v4l2_exposure_auto_type {
V4L2_EXPOSURE_AUTO = 0,
V4L2_EXPOSURE_MANUAL = 1,
...
So instead of passing !!ctrls->auto_exp->val they should have been passing
ctrls->auto_exp->val == V4L2_EXPOSURE_AUTO, iow the passed value was
inverted of what it should have been.
Also remove ov2680_g_volatile_ctrl() since without auto support the gain
and exposure controls are not volatile.
This also fixes the control values not being properly applied in
ov2680_mode_set(). The 800x600 mode register-list also sets gain,
exposure and vflip overriding the last set ctrl values.
ov2680_mode_set() does call ov2680_gain_set() and ov2680_exposure_set()
but did this before writing the mode register-list, so these values
would still be overridden by the mode register-list.
Add a v4l2_ctrl_handler_setup() call after writing the mode register-list
to restore all ctrl values. Also remove the ctrls->gain->is_new check from
ov2680_gain_set() so that the gain always gets restored properly.
Last since ov2680_mode_set() now calls v4l2_ctrl_handler_setup(), remove
the v4l2_ctrl_handler_setup() call after ov2680_mode_restore() since
ov2680_mode_restore() calls ov2680_mode_set().
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The initial state of RESETB input signal of OV5640 should be
asserted, i.e. the sensor should be in reset. This is not the
case, make it so.
Since the subsequent assertion of RESETB signal is no longer
necessary and the timing of the power sequencing could be
slightly adjusted, add annotations to the delays which match
OV5640 datasheet rev. 2.03, both:
figure 2-3 power up timing with internal DVDD
figure 2-4 power up timing with external DVDD source
The 5..10ms delay between PWDN assertion and RESETB assertion
is not even documented in the power sequencing diagram, and
with this reset fix, it is no longer even necessary.
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set OV5640_REG_IO_MIPI_CTRL00 bit 2 to 1 instead of 0, since 1 means
MIPI CSI2 interface, while 0 means CPI parallel interface.
In the ov5640_set_power_mipi() the interface should obviously be set
to MIPI CSI2 since this functions is used to power up the sensor when
operated in MIPI CSI2 mode. The sensor should not be in CPI mode in
that case.
This fixes a corner case where capturing the first frame on i.MX8MN
with CSI/ISI resulted in corrupted frame.
Fixes: aa4bb8b883 ("media: ov5640: Re-work MIPI startup sequence")
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> # [Test on imx6q]
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Jai Luthra <j-luthra@ti.com> # [Test on bplay, sk-am62]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a driver for the DW9719 VCM. The driver creates a v4l2 subdevice
and registers a control to set the desired focus.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx219_set_pad_format() function adjusts the media bus code provided
through the v4l2_subdev_format parameter to a media bus code known
to be supported by the sensor.
The same exact operation is performed by the imx219_get_format_code()
function which called by imx219_update_pad_format(), which is in the
imx219_set_pad_format() call path.
Remove the duplicated operation and simplify imx219_set_pad_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The set_fmt and init_cfg functions both fills a v4l2_mbus_framefmt
instance, passing in the mode and the media bus code. While set_fmt
uses function helpers, init_cfg open-codes the assignments.
Simplify the format initialization by moving it to a common helper.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Port the imx219 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX219 is a RAW sensor. Fix the colorspace configuration by
using V4L2_COLORSPACE_RAW and adjust the quantization and transfer
function values. Drop ycbcr_enc as it doesn't apply to RAW sensors.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Complete the default format initialization in init_cfg() filling in
the fields for the colorspace configuration copied from
imx219_set_default_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the init_cfg pad level operation instead of the internal subdev
open operation to set default formats on the pads.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx219 is using the name "codes" for the mbus formats array. The
name is too generic and not easy to read and follow in the code. Change
it to imx219_mbus_formats.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new comon CCI register access helpers to replace the private
register access helpers in the imx290 driver.
[Sakari Ailus: Squashed the patch to address a merge issue in Kconfig]
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new comon CCI register access helpers to replace the private
register access helpers in the ov5693 driver.
[Sakari Ailus: Squashed the patch to address a merge issue in Kconfig]
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As selecting V4L2_FWNODE, MEDIA_CONTROLLER and VIDEO_V4L2_SUBDEV_API are
now selected by the top level menu, they can be dropped from the
individual drivers. Also dropped selecting V4L2_ASYNC for a single driver
as this is already implied by V4L2_FWNODE.
Similarly, the I2C dependency is now also in the top level menu, so remove
it, as well as VIDEO_DEV which isn't needed by camera sensor drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Select V4L2_FWNODE and VIDEO_V4L2_SUBDEV_API for all sensor drivers. This
also adds the options to drivers that don't specifically need them, these
are still seldom used drivers using old APIs. The upside is that these
should now all compile --- many drivers have had missing dependencies.
The "menu" is replaced by selectable "menuconfig" to select the needed
V4L2_FWNODE and VIDEO_V4L2_SUBDEV_API options.
Also select MEDIA_CONTROLLER which VIDEO_V4L2_SUBDEV_API effectively
depends on, and add the I2C dependency to the menu.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # for >= 6.1
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
FPD-Link has an operating mode that used to be called "asynchronous" in
the hardware documentation, but that has been changed to non-synchronous
already quite a while back. The ub960 driver still had one instance of
the old naming, so let's rename it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add support for FPD-Link non-sync mode with external clock. The only
thing that needs to be added is the calculation for the clkout.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Separate clkout calculations and register writes into two functions:
ub953_calc_clkout_params and ub953_write_clkout_regs, and add a struct
ub953_clkout_data that is used to store the clkout parameters.
This simplifies the clkout management.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Allow using FPD-Link in async mode. The driver handles it correctly, but
the mode was blocked at probe time as there wasn't HW to test this with.
Now the mode has been tested, and it works.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Handle V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK flag to configure the CSI-2 RX
continuous/non-continuous clock register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use v4l2_fwnode_endpoint_parse() to parse the sink endpoint parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use v4l2_fwnode_endpoint_parse() to parse the sink endpoint parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use 'clock-noncontinuous' from DT to configure the
continuous/non-continuous clock setting for the TX ports.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode
matching") recently changed how async sub-device matching works. This
breaks the UB9x3 drivers, as they set the subdev.fwnode to an endpoint.
Afaiu, the fix is simply to not set subdev.fwnode at all.
Fixes: 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cascade the s_stream call to the source subdev whenever the bridge
streaming is enable / disabled.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Initialise best_div local variable to avoid a compiler warning. The
warning was harmless though.
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Set the v4l2_device already in async notifier init, so struct device
related to it will be available before the notifier is registered. This
requires separating notifier initialisation into two functions, one that
takes v4l2_device as its argument, v4l2_async_nf_init and
v4l2_async_subdev_nf_init, for sub-device notifiers. Registering the
notifier will use a single function, v4l2_async_nf_register.
This is done in order to make struct device available earlier, during
construction of the async connections, for sensible debug prints.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Return the two CSI-2 transmitters of adv748x to endpoint matching. This
should make the driver work again as expected.
Fixes: 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rename v4l2_async_subdev as v4l2_async_connection, in order to
differentiate between the sub-devices and their connections: one
sub-device can have many connections but the V4L2 async framework has so
far allowed just a single one. Connections in this context will later
translate into either MC ancillary or data links.
This patch prepares changing that relation by changing existing users of
v4l2_async_subdev to switch to v4l2_async_connection. Async sub-devices
themselves will not be needed anymore
Additionally, __v4l2_async_nf_add_subdev() has been renamed
__v4l2_async_nf_add_connection().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2 async sub-device matching originally used the device nodes only.
Endpoint nodes were taken into use instead as using the device nodes was
problematic for it was in some cases ambiguous which link might have been
in question.
There is however no need to use endpoint nodes on both sides, as the async
sub-device's fwnode can always be trivially obtained using
fwnode_graph_get_remote_endpoint() when needed while what counts is
whether or not the link is between two device nodes, i.e. the device nodes
match.
This will briefly break the adv748x driver but it will be fixed later in
the set, by patch "media: adv748x: Return to endpoint matching".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix the following warning:
drivers/media/i2c/ds90ub913.c:488:9: warning: 'v' may be used uninitialized [-Wmaybe-uninitialized]
488 | ub913_write(priv, UB913_REG_GENERAL_CFG,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
489 | v | UB913_REG_GENERAL_CFG_CRC_ERR_RESET);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/ds90ub913.c:477:12: note: 'v' was declared here
477 | u8 v, v1, v2;
| ^
Fix the warning by initializing the variable to 0. Proper error handling
here would be somewhat pointless, as we are just printing register
values, and the user will see an error about the failed i2c transaction.
Fixes: c158d0d4ff ("media: i2c: add DS90UB913 driver")
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Closes: https://lore.kernel.org/all/a0180488-f7f5-8538-a8bb-52ae52912835@xs4all.nl/
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
struct i2c_driver::probe_new is about to go away. Switch the driver to
use the probe callback with the same prototype.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
struct i2c_driver::probe_new() is about to go away. Since I converted
all drivers below drivers/media use struct i2c_driver::probe, three more
drivers were added in the following commits that use .probe_new():
commit 6363db1c9d ("media: i2c: add DS90UB953 driver")
commit c158d0d4ff ("media: i2c: add DS90UB913 driver")
commit afe267f2d3 ("media: i2c: add DS90UB960 driver")
Switch these driver to use the probe callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: use proper commit description style]
Smatch warns:
drivers/media/i2c/ds90ub960.c:1671 ub960_rxport_add_serializer():
err: 'rxport->ser.client' dereferencing possible ERR_PTR()
i2c_new_client_device() returns error pointers on failure and in
dev_dbg statement we are dereferencing error pointer which is a bug.
Fix this by using IS_ERR() which checks for error pointers.
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Remove .owner field if calls are used which set it automatically.
to silence the warning:
./drivers/media/i2c/ds90ub953.c:1390:3-8: No need to set .owner here. The core will do it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5902
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add the error code of a failed i2c transfer to the error message.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add driver for TI DS90UB953 FPD-Link III Serializer.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add driver for TI DS90UB913 FPD-Link III Serializer.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add driver for TI DS90UB960 FPD-Link III Deserializer.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On ACPI based platforms, the ov13b10 camera sensor need to be powered
up by acquire the PM resource from INT3472. INT3472 will register one
regulator 'avdd', one reset gpio and clock source for ov13b10.
Add 2 power interfaces that are registered as runtime PM callbacks.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hao Yao <hao.yao@intel.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The supported ad5820 and ad5821 VCMs both use a single 16 bit register
which is written by sending 2 bytes with the data directly after sending
the i2c-client address.
The ad5823 OTOH has a more typical i2c / smbus device setup with multiple
8 bit registers where the first byte send after the i2c-client address is
the register address and the actual data only starts from the second byte
after the i2c-client address.
The ad5823 i2c_ and of_device_id-s was added at the same time as
the ad5821 ids with as rationale:
"""
Some camera modules also refer that AD5823 is a replacement of AD5820:
https://download.kamami.com/p564094-OV8865_DS.pdf
"""
The AD5823 may be an electrical and functional replacement of the AD5820,
but from a software pov it is not compatible at all and it is going to
need its own driver, drop its id from the ad5820 driver.
Fixes: b8bf73136b ("media: ad5820: Add support for ad5821 and ad5823")
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The format param actually is not used in imx290_ctrl_update
function, let's drop this
Fixes: bc35f9a21a ("media: i2c: imx290: Fix the pixel rate at 148.5Mpix/s")
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On ACPI systems, the HID of ov13b10 is 'OVTI13B1', add this new
HID in acpi IDs table to make driver support it.
Signed-off-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov13b10 need be connected to a CIO2 or IPU device by bridge, sometimes
the bridge driver was not probed before ov13b10 driver, then the absence
of the fwnode endpoint for this device is expected, so driver return
-EPROBE_DEFER in this case to let the probe occur after bridge driver.
Signed-off-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
OV5640 will output abnormal image data when work at low resolution
(320x240, 176x144 and 160x120) after switching from high resolution,
such as 1080P, the time interval between high and low switching must
be less than 1000ms in order to OV5640 don't enter suspend state during
the time.
The reason is by 0x3824 value don't restore to initialize value when
do resolution switching. In high resolution setting array, 0x3824 is
set to 0x04, but low resolution setting array remove 0x3824 in commit
db15c1957a ("media: ov5640: Remove duplicated mode settings"). So
when do resolution switching from high to low, such as 1080P to 320x240,
and the time interval is less than auto suspend delay time which means
global initialize setting array will not be loaded, the output image
data are abnormal. Hence move 0x3824 from ov5640_init_setting[] table
to ov5640_setting_low_res[] table and also move 0x4407 0x460b, 0x460c
to avoid same issue.
Fixes: db15c1957a ("media: ov5640: Remove duplicated mode settings")
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The HTS value cannot be directly compared to the sensor's output
size. It needs to be converted to an absolute time unit.
Additionally, the hblank value need to be modified as it was
previous invalid.
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove Shawn Tu's and Chiranjeevi Rapolu's e-mail addresses as they are no
longer function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/media/i2c/max9286.c:1707:34: error: ‘max9286_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/media/i2c/ov7740.c:1203:34: error: ‘ov7740_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/media/i2c/ov2680.c:1149:34: error: ‘ov2680_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/media/i2c/ov2640.c:1290:34: error: ‘ov2640_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/media/i2c/mt9m111.c:1370:34: error: ‘mt9m111_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/media/i2c/isl7998x.c:1557:34: error: ‘isl7998x_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Address these compiler warnings by initialising the m_best and p_best
values to 0 and 1 respectively (as latter is used as a divisor):
drivers/media/i2c/tc358746.c: In function 'tc358746_find_pll_settings':
>> drivers/media/i2c/tc358746.c:817:13: warning: 'p_best' is used uninitialized
[-Wuninitialized]
817 | u16 p_best, p;
| ^~~~~~
>> drivers/media/i2c/tc358746.c:816:13: warning: 'm_best' is used uninitialized
[-Wuninitialized]
816 | u16 m_best, mul;
| ^~~~~~
The warnings may well be a false positive but it is difficult for a
compiler to find out whether that truly is the case.
Closes: https://lore.kernel.org/oe-kbuild-all/202305301627.fLT3Bkds-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 80a21da360 ("media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The tc358746 driver selects CONFIG_GENERIC_PHY_MIPI_DPHY and links to
that, but this fails when CONFIG_GENERIC_PHY is disabled, because Kbuild
then never enters the drivers/phy directory for building object files:
ERROR: modpost: "phy_mipi_dphy_get_default_config_for_hsclk" [drivers/media/i2c/tc358746.ko] undefined!
Add an explicit 'select GENERIC_PHY' here to ensure that the directory
is entered, and add another dependency on that symbol so make it
more obvious what is going on if another driver has the same problem,
as this will produce a Kconfig warning.
Link: https://lore.kernel.org/linux-media/20230623152318.2276816-1-arnd@kernel.org
Fixes: 80a21da360 ("media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
pm_runtime_get_if_in_use() does not only return nonzero values when
the device is in use, it can return a negative errno too.
And especially during resuming from system suspend, when runtime pm
is not yet up again, -EAGAIN is being returned, so the subsequent
pm_runtime_put() call results in a refcount underflow.
Fix system-resume by handling -EAGAIN of pm_runtime_get_if_in_use().
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Fixes: e8c0882685 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When setting formats on the sink pad, propagate the adjusted format over
to the subdev's source pad. Use the MIPID02_SOURCE macro to fetch the
pad's try format rather than relying on the pad field of the format to
facilitate this - the function is specific to the source pad anyway.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
[Sakari Ailus: Line wrap, fix subject]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Format propagation in the st-mipid02 driver is incorrect in that when
setting format for V4L2_SUBDEV_FORMAT_TRY on the source pad, the
_active_ rather than _try_ format from the sink pad is propagated.
This causes problems with format negotiation - update the function to
propagate the correct format.
Fixes: 642bb5e88f ("media: st-mipid02: MIPID02 CSI-2 to PARALLEL bridge driver")
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Statically allocated array of pointers to hwmon_channel_info can be made
const for safety.
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The ov5640_update_pixel_rate() function handles the parallel and MIPI
CSI-2 cases separately.
When running on a parallel setup the V4L2_CID_PIXEL_RATE value is
calculated at the beginning of the function using the values configured
with the frame_interval operations, and then the function immediately
returns.
The remaining of the function handles the MIPI CSI-2 configuration and
should not use the 'current_fr' and 'def_fps' fields as those are only
relevant for parallel mode.
Drop a small section of dead code that updates vblank using
frame_interval on a MIPI CSI-2 setup.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The 'current framerate' parameter passed to ov5640_try_fmt_internal() is
unsued. Drop it.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When OV5640 work at DVP mode, the default initialization settings
make it output 30 frames per second. But when it work at CSI-2 mode
the default link frequency will make it output 60 frames per second,
so correct the comments to make it more clear.
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Update pixel_rate and link frequency for 1920x1080@30
while changing mode.
Update vblank value while changing mode
Add support to handle multiple link frequencies.
Add dummy ctrl cases for pixel_rate and link frequency
to avoid error while changing the modes dynamically.
Update default link frequency from device tree max link
frequency value.
Update init_cfg() function to update the link frequency
menu_skip_mask value.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
[Sakari Ailus: Document menu_skip_mask, remove extra blank line.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
dev_err_probe() already display the error code. There is no need to
duplicate it explicitly in the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The "& IMX296_TMDOUT_MASK" means that "tmdout" can't be negative so the
error checking will not work.
Fixes: cb33db2b6c ("media: i2c: IMX296 camera sensor driver")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
devm_clk_get() will return either an error or NULL, which the driver
handles, continuing to use the clock of reading the value of the
clock-frequency property.
However, the value of ov5670->xvclk is left as-is and the other clock
framework functions aren't capable of handling error values.
Use devm_clk_get_optional() to obtain NULL instead of -ENOENT.
Fixes: 8004c91e20 ("media: i2c: ov5670: Use common clock framework")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The vs6624 camera sensor driver doesn't support DT and relies on
platform data. The last board files supplying platform data for that
device have been removed from the kernel in v4.17. The driver hasn't
been used since them. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sr030pc30 camera sensor driver doesn't support DT and relies on
platform data. No board file has ever provided platform data for that
device. The driver has thus never been used in the mainline kernel since
its introduction in v2.6.37. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The s5k6aa camera sensor driver doesn't support DT and relies on
platform data. The last board files supplying platform data for that
device have been removed from the kernel in v3.11. The driver hasn't
been used since them. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The noon010pc30 camera sensor driver doesn't support DT and relies on
platform data. The last board files supplying platform data for that
device have been removed from the kernel in v3.16. A device tree file
referencing the device has been added in v3.17, but without
corresponding DT bindings, and with DT support in the driver. The driver
thus hasn't been used since v316. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The mt9t001 camera sensor driver doesn't support DT and relies on
platform data. No board file has ever provided platform data for that
device. The driver has thus never been used in the mainline kernel since
its introduction in v3.2. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The mt9m032 camera sensor driver doesn't support DT and relies on
platform data. No board file has ever provided platform data for that
device. The driver has thus never been used in the mainline kernel since
its introduction in v3.4. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The m5mols camera sensor driver doesn't support DT and relies on
platform data. The last board files supplying platform data for that
device have been removed from the kernel in v3.11. The driver hasn't
been used since them. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ad9389b video encoder driver doesn't support DT and relies on
platform data. No board file has ever provided platform data for that
device. The driver has thus never been used in the mainline kernel since
its introduction in v3.7. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Also dev_err_probe message require a trailing \n.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
MIPI CCS uses a 16-bit MIPI manufacturer identifier for firmware filenames
compared to older 8-bit identifier used by SMIA. The requested firmware
files used the MIPI manufacturer ID even for SMIA compliant devices,
effectively making the manufacturer ID 0.
While CCS static data is a feature of CCS 1.1, it has no hardware
dependencies. Making this feature available for SMIA devices helps adding
support for them and avoids requesting ill-generated CCS static data file
names. The files are named as:
ccs/smiapp-module-vv-mmmm-rrrr.fw,
ccs/smiapp-sensor-vv-mmmm-rr.fw and
ccs/smia-sensor-vv-mmmm-rr.fw
where vv is the manufacturer ID, mmmm is the model ID and rr or rrrr is
the revision number.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some modules don't have any model identification information in the
register address space. The driver as a SMIA++ driver attempted to use
sensor information in this case. This workaround is definitely not for CCS
devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Read 16-bit sensor revision number if the 8-bit register has value 0.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
No longer mirror flipping controls if the sensor is mounted upside down.
This way the behaviour of the flipping controls and rotation of the sensor
are aligned with the rest of the drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The "rotation" fwnode device property is intended to allow specify the
sensor's physical mounting rotation, so that it can be exposed through
the read-only V4L2_CID_CAMERA_SENSOR_ROTATION control and applications
can decide how to compensate for that.
The imx258 driver has read-only VFLIP and HFLIP enabled, resulting in
a 180 degrees image rotation being produced by the sensor. But this
doesn't imply that the physical mounting rotation should match the
driver's implementation.
Now that the driver registers V4L2_CID_CAMERA_SENSOR_ROTATION
and V4L2_CID_HFLIP/VFLIP correctly, userspace has all the required
information to handle the rotation correctly, hence it is not necessary
to require the 'rotation' property to be fixed to 180 degrees in DTS.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Register controls for V4L2_CID_HFLIP and V4L2_CID_VFLIP.
The controls are registered as read-only and enabled by default, as the
driver embeds a 180 degrees rotation in its programming sequences and
only supports that mode of operations.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Adding additional cropped 2592x1444 resolution
for QHD output from Hi556 sensor
Also implement the get_selection pad operation for the Hi556 sensor driver.
The supported targets report the sensor's native size, the crop default
rectangle and the crop rectangle.
Signed-off-by: Jim Lai <jim.lai@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The ADV7604, ADV7611 and ADV7612 software manuals document the CP_HUE
value differently:
- For ADV7604 and ADV7611, the hue is specified as an unsigned 8-bit
value, and calculated as
(CP_HUE[7:0] * 180) / 256 - 90
with the range set to [-90°, 90°]. Additionally, the values 0x00, 0x0f
and 0xff are documented as corresponding to -90°, 0° and 90°
respectively.
- For ADV7612, the hue is specified as a signed 8-bit value in the range
[0°, 360°[ without any formula. Additionally, the value 0x00 is
documented as corresponding to 0°.
The ADV7604 and ADV7611 documentation is clearly wrong as the example
values don't correspond to the formula. Furthermore, the [-90°, 90°]
range seems incorrect as it would cover only half of the hue space.
The ADV7612 documentation is better, although the range should likely be
[-180°, 180°[ if the value is signed. Given that the values wrap around,
this makes no difference in practice.
The hue values have been verified on ADV7612 to follow the
documentation. There is a high chance they do as well on ADV7604 and
ADV7611.
In any case, all software manuals document the register as 8-bit, so the
current range of the V4L2 hue control [0, 128] is not correct. Expand it
to cover the full 8-bit space, using unsigned values to avoid breaking
any application that may rely on 128 being a valid value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The video adjustments (contrast, brightness, saturation and hue) are
ignored by default by the device when the VID_ADJ_EN bit is clear. The
corresponding V4L2 controls exposed by the drivers have thus no effect.
Fix this by setting the VID_ADJ_EN bit.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In some setups XSHUTDOWN is connected to DOVDD when it's unused,
therefore treat the reset gpio as optional.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
hi846_init_controls doesn't clean the allocated ctrl_hdlr
in case there is a failure, which causes memleak. Add
v4l2_ctrl_handler_free to free the resource properly.
Fixes: e8c0882685 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Reviewed-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It the device is probed in non-zero ACPI D state, the module
identification is delayed until the first streamon.
The module identification has two parts: deviceID and version. To rea
the version we have to enable OTP read. This cannot be done during
streamon, becase it modifies REG_MODE_SELECT.
Since the driver has the same behaviour for all the module versions, do
not read the module version from the sensor's OTP.
Cc: stable@vger.kernel.org
Fixes: 0e014f1a8d ("media: ov8856: support device probe in non-zero ACPI D state")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use devm_clk_get_optional() instead of hand writing it.
This saves some loC and improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
If the pattern generator is enabled the device shall not be queried for
timings. Instead the timings programmed shall be reported as they are
the ones being used to generate the pattern.
Before this change an external HDMI source needed to be connected for
the pattern generator to work. The driver would query this external
HDMI source for timings and program the pattern generator using those.
With this change the user can control the timings and have the pattern
generator work without the need of an external HDMI source being
connected.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When initializing the HDMI block during probe an initial set of timings
are selected. These timings are stored in the drivers private data, but
not written to the device.
This in itself is not bad, but in s_dv_timings() the timings stored in
the drivers private data are compared to the new timings, if they match
no action is taken. This creates the corner-case where the timing
selected at initialization is the first timings a user want to use as
the driver then never writes it to the device preventing proper
operation.
Fix this by writing the timings to the device at initialization in
addition to storing them in the drivers private data.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The loop to match the requested timings with the ones supported by the
driver is incorrect. It always iterates thru the whole array of
supported modes. The bounds check after the loop always triggers
resulting in adv748x_hdmi_set_video_timings() always returning -EINVAL.
Fix this by correcting the lookup to break the loop when a match is
found.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some platforms may not be capable of supporting the bandwidth
required for 12 bit or 3840x2160@60 resolutions.
Add support for dynamically selecting 10 bit and 1920x1080@30
resolutions while leaving the existing configuration as default.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
CC: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Prakash Battu <Prakash.Battu@microchip.com>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are some missing reset reg_mode values for the 3840x2160@60
resolution. The camera sensor still works in 3840x2160@60 resolution mode
because of the register reset values. This is an issue when we change the
modes dynamically. As an example, when we change the mode from 1920x1080@30
resolution to 3840x2160@60 resoultion then the mode values will be written
to the registers from the array mode_3840x2160_regs[] which gives the wrong
output which is incorrect resolution.
So add the missing reset values to the mode_3840x2160_regs[].
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For every mode we will get new set of values for hbalnk so use
__v4l2_ctrl_modify_range() to support multi modes for hblank.
The hblank value is readonly in the driver. because of this the function
returns error if we try to change. so added dumy return case in
imx334_set_ctrl function.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Suggested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The control handler is leaked in some probe-time error paths, as well as
in the remove path. Fix it.
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Analogous to e.g. the imx219. This enables propagating
V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION values.
The motivation is to allow libcamera detect these values from the device
tree and propagate them further to e.g. Pipewire.
While at it, reserve space for 3 additional controls even if
v4l2_ctrl_new_fwnode_properties() can only register 2 of them, to fix the
existing implementation which reserve space for 8 controls but actually
registers 9.
[Sakari Ailus: Rewrapped the commit message and removed changelog]
Signed-off-by: Robert Mader <robert.mader@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is not expected that trying to set the sensor to
streaming mode when trying to set initial sensor configuration.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in
probe or when starting streaming.
Signed-off-by: Arec Kao <arec.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for the .get_selection() pad operation to the ov2685 sensor
driver.
Report the native sensor size (pixel array), the crop bounds (readable
pixel array area) and the current and default analog crop rectangles.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov2685 driver by attempting to parse them from firmware.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the sensor doens't power up correctly, for example due to incorrect
devicetree description, the power up i2c writes will fail.
Add an error print for this situation.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx296 driver uses the subdev active state, there's no need to
implement the .get_fmt() operation manually. Use the
v4l2_subdev_get_fmt() helper instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5670 driver tries to get a reference to the xvclk provider by using
the common cock framework and deflects to parsing the "clock-frequency"
property in case the clock provider is not specified in the firmware
interface, detected by checking if ov5670->xvclk == PTR_ERR(-ENOENT).
However, as reported by the Smatch static checker, if CONFIG_HAVE_CLK is
not enabled, devm_clk_get() returns 0 which when passed to PTR_ERR()
means success causing the driver to fail without propagating any error
code up.
Explicitly handle the case where ov5670->xvclk it set to NULL, forcing
the code to parse the "clock-frequency" property in case CONFIG_HAVE_CLK
is not enabled, as suggested by Dan Carpenter.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently the driver always configures the sensor for dual-lane MIPI
output, but it also supports single-lane output. Add support for that by
checking the data-lanes fwnode property how many lanes are used and
configure the necessary registers based on that.
To achieve this we move setting register 0x3018 out of the general reg
sequence so we set it to the correct value. The pixel_rate value also
needs to be adjusted.
[Sakari Ailus: Use div_s64 to divide a 64-bit number]
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace the unusual const char *err_msg usage with dev_err_probe which
also handles -EPROBE_DEFER better by not printing the message to kmsg.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Both sensors are quite similar. Their specs only differ regarding LVDS
and parallel output but are identical regarding MIPI-CSI-2 interface.
But they use a different init setting of hard-coded values, taken from
the datasheet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
imx290_start_streaming logs what failed, but not the error
code from that function. Add it into the log message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports H & V flips, so add the relevant hooks for
V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
Note that the Bayer order is maintained as the readout area
shifts by 1 pixel in the appropriate direction (note the
comment about the top margin being 8 pixels whilst the bottom
margin is 9). The V4L2_SEL_TGT_CROP region is therefore
adjusted appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports either a 37.125 or 74.25MHz external, but
the driver only supported 37.125MHz.
Add the relevant register configuration for either clock
frequency option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
IMX290_CTRL_07 was written from both imx290_global_init_settings
and imx290_1080p_settings and imx290_720p_settings.
Remove it from imx290_global_init_settings as the setting varies
based on the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The default VMAX for 60fps in 720p mode is 750 according to the
datasheet, however the driver always left it at 1125 thereby stopping
60fps being achieved.
Make VMAX (and therefore V4L2_CID_VBLANK) mode dependent so that 720p60
can be achieved.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_VBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
V4L2_CID_VBLANK also sets the limits for the exposure control,
therefore exposure ranges have to be updated when vblank changes
(either via s_ctrl, or via changing mode).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_HBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" added support for the increased link frequencies
on 2 data lanes, but didn't update the CSI timing registers in
accordance with the datasheet.
Use the specified settings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit "97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Any V4L2 subdevice that implements controls and declares
V4L2_SUBDEV_FL_HAS_DEVNODE should also declare V4L2_SUBDEV_FL_HAS_EVENTS
and implement subscribe_event and unsubscribe_event hooks.
This driver didn't and would therefore fail v4l2-compliance
testing.
Add the relevant hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
