The V4L2_CID_3A_LOCK bitmask control allows applications to pause
or resume the automatic exposure, focus and wite balance adjustments.
It can be used, for example, to lock the 3A adjustments right before
a still image is captured, for pre-focus, etc.
The applications can control each of the algorithms independently,
through a corresponding control bit, if driver allows that.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add control for the scene mode feature available in image sensor
with more advanced ISP firmware. The V4L2_CID_SCENE_MODE menu
control allows to select a set of parameters or a specific image
processing and capture control algorithm optimized for common
image capture conditions.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_EXPOSURE_METERING control allows to determine
a method used by the camera for measuring the amount of light
available for automatic exposure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ISO sensitivity and ISO auto/manual controls. The sensitivity
values are related to level of amplification of the analog signal
between image sensor and ADC. These controls allow to support sensors
exposing an interface to accept the ISO values directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add V4L2_CID_IMAGE_STABILIZATION control for the camera image
stabilization feature. This control can be used to enable/disable
image stabilization. It might get converted to a menu control
in future if more options are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add V4L2_CID_WIDE_DYNAMIC_RANGE camera class control for the
camera wide dynamic range (WDR, HDR) feature. This control
can be used to enable/disable wide dynamic range. It might
get converted to a menu control in future if more options
are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE control which is
an extended version of the V4L2_CID_AUTO_WHITE_BALANCE control,
including white balance presets. The following presets are defined:
- V4L2_WHITE_BALANCE_INCANDESCENT,
- V4L2_WHITE_BALANCE_FLUORESCENT,
- V4L2_WHITE_BALANCE_FLUORESCENT_H,
- V4L2_WHITE_BALANCE_HORIZON,
- V4L2_WHITE_BALANCE_DAYLIGHT,
- V4L2_WHITE_BALANCE_FLASH,
- V4L2_WHITE_BALANCE_CLOUDY,
- V4L2_WHITE_BALANCE_SHADE.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds v4l2_ctrl_new_int_menu() helper function which can be used
in drivers for creating standard integer menu control with driver-specific
menu item list. It is similar to v4l2_ctrl_new_std_menu(), except it doesn't
have a mask parameter and an additional qmenu parameter allows passing
an array of signed 64-bit integers as the menu item list.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds definition of additional color effects:
- V4L2_COLORFX_AQUA,
- V4L2_COLORFX_ART_FREEZE,
- V4L2_COLORFX_SILHOUETTE,
- V4L2_COLORFX_SOLARIZATION,
- V4L2_COLORFX_ANTIQUE,
- V4L2_COLORFX_SET_CBCR.
The new V4L2_COLORFX_CBCR control is added to allow setting
the fixed Cb, Cr values that replace chroma Cb/Cr coefficients
in case of V4L2_COLORFX_SET_CBCR effect.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The radio-si470x-usb driver supported both autosuspend and it stopped the
radio the moment the last user of the radio device closed it. However, that
was very confusing since if you play the audio from the device (e.g. through
arecord -D ... | aplay) then no sound would play unless you had the radio
device open at the same time, even though there is no need to do anything
with that node.
On the other hand, the actual suspend/resume functions didn't do anything,
which would fail if you *did* have the radio node open at that time.
So:
- remove autosuspend (bad idea in general for USB radio devices)
- move the start/stop out of the open/release functions into the resume/suspend
functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to report an error in the log, you are already returning
that error to userspace after all.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans up the code and si470x now uses the proper v4l2 frameworks
and passes most of the v4l2-compliance tests.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver uses the ctrl value passed in as a bool to determine whether
to enable auto-exposure, but the auto-exposure setting is defined as an
enum where AUTO has a value of 0 and MANUAL has a value of 1. This leads
to a reversed logic where if you send in AUTO, it actually sets manual
exposure and vice-versa.
Signed-off-by: Kartik Mohta <kartikmohta@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following compilation failure:
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
by adding a dependency on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a copy-paste typo and a nested locking function call in mt9m032.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add four new controls to configure black level compensation (BLC):
- V4L2_CID_BLC_AUTO selects between manual and auto BLC
- V4L2_CID_BLC_TARGET_LEVEL sets the target level for auto BLC
- V4L2_CID_BLC_ANALOG_OFFSET sets the analog offset for manual BLC
- V4L2_CID_BLC_DIGITAL_OFFSET sets the digital offset for manual BLC
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the GPIO from the sensor driver instead of calling back to board
code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of passing a color/monochrome flag through platform data, rely
on the I2C device name to identify the chip model.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add all known reference design USB IDs.
Rename two earlier reference design USB IDs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can use tuner ID instead of HW not supported flag.
Lesser code is better code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes most problems when having more than one device connected
as demod and tuner configurations are not shared.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
af9033: implement read_ber and read_ucblocks functions. Version 2 of patch that
reflects my findings on the behaviour of abort_cnt, err_cnt and bit_cnt:
- bit_cnt is always 0x2710 (10000)
- abort_cnt is between 0 and 0x2710
- err_cnt is between 0 and 640000 (= 0x2710 * 8 * 8)
in the current implementation BER is calculated as the number of bit errors per
processed bits, ignoring those bits that are already discarded and counted in
abort_cnt, i.e. UCBLOCKS.
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not used anymore since new firmware downloader. I forget to remove
those earlier when changed firmware downloader.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix USB buffer len to maximum possible.
Various log writing fixes, remove extra new lines and excessive
type casts. Rename and type change some variables.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When setting TRY crop on the sub-device the mutex was erroneously acquired
rather than released on exit path. This bug is present in kernels starting
from v3.2.
Cc: stable@vger.kernel.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move drivers/input/fixp-arith.h to include/linux so that the functions
defined there can be used by other subsystems, for instance some video
devices ISPs can control the output HUE value by setting registers for
sin(HUE) and cos(HUE).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also merge the "COLORS" control into it as it was V4L2_CID_SATURATION
anyway.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enabling vflip leads to a much better image, with vflip disabled the
image looks washed out as if there is a too high brightness setting.
Since we don't know how to lower the brightness setting when not
vflipping, simply always vflip and tell userspace to flip the image back,
resulting in a much better (less washed out) image.
Since the image is now no longer too bright, also modify the luminance
level the auto-gain algorithm aims for.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our init sequence was not setting the register page to point to bank 1
before setting what should be the control reg. This causes the camera to
sometimes have its LED on after init. First selecting register bank 1,
rather then assuming the current register bank is bank 1, fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the pac207 driver has been converted to the control framework, there
are no remaining users.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pac207's exposure control is a clock-divider, so it goes with quite
big steps. So lets use an autogain algorithm optimised for that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We intend to eventually port all sub-drivers to the control-framework. At
which point it will make more sense to have the ctrl_handler in gspca_dev
then to have it in the subdrivers. Lets move it there now, to avoid a lot
of work to move it later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that stv06xx is using the control framework it is no longer necessary
to have a (non const) copy of sd_desc inside the sd specific data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
HdG:
1) Let the gspca-core cleanup the controls on control-init error, like
with the other converted sub drivers
2) Note this also fixes a bug in the hdcs1020 support which was wrongly
reporting an exposure range of 0-65535, even though the effective range was
only 0-255
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
HdG: Small fix: don't register some controls for sensors which don't
have an implementation for them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial version was done by HV, corrections were made by HdG, and some
final small changes again by HV.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even with BRC the highest quality setting is not usable, BRC strips so
much data from each MCU that the quality becomes worse then using a lower
quality setting to begin with.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Always automatically adjust the Bit Rate Control setting as needed, independent
of the sensor type. BRC is needed to not run out of bandwidth with higher
quality settings independent of the sensor.
Also only automatically adjust BRC, and don't adjust the JPEG quality control
automatically, as that is not needed and leads to ugly flashes when it is
changed. Note that before this patch-set the quality was never changed
either due to the bugs in the quality handling fixed in previous patches in
this set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code is using bits 0-1 of register 8 of the zc3xx controller
to set the JPEG quality, but the correct bits are bits 1-2. Bit 0 selects
between truncation or rounding in the quantization phase of the compression,
since rounding generally gives better results it should thus always be 1.
This patch also corrects the quality percentages which belong to the 4
different settings.
Last this patch removes the different reg 8 defaults depending on the sensor
type. Some of them where going for a default quality setting of 50%, which
generally is not necessary in any way and results in poor image quality.
75% is a good default to use for all scenarios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the user changes the JPEG quality while the camera is streaming, the
driver should not only change the JPEG headers send to userspace, but also
actually tell the camera to use a different quantization table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor specific dev_post_unset_alt functions all try to write to the
bridge, and none free any memory, so they should be skipped if stop0
is called on disconnection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is necessary to ensure that worker-threads accessing the device
are stopped before our disconnect handler returns.
This causes a problem with stream_off calling sd_stop0 a second time
when the device handle is closed. This is fixed by setting
gscpa_dev->streaming to 0 on disconnect.
Note that now stream_off will never be called on a disconnected device,
and the present check can thus be removed from stream_off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
So that we don't start a read stream when an app is only polling for control
events.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to latency concerns the VIDIOC_QBUF, DQBUF and QUERYBUF do not use the
core lock, instead they rely only on queue_lock.
Changes by HdG:
1) Change release from the video_device to the v4l2_device, to avoid a
race on disconnect.
2) Adjust for the V4L2 core changes which cause non ioctl fops to no longer
take the V4L2 core lock.
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two bugs here: first the calls to stop0 (in gspca_suspend) and
gspca_init_transfer (in gspca_resume) need to be called with the usb_lock held.
That's true for the other places they are called and it is what subdrivers
expect. Quite a few will unlock the usb_lock in stop0 while waiting for a
worker thread to finish, and if usb_lock isn't held then that can cause a
kernel oops.
The other problem is that a worker thread needs to detect that it has to
halt due to a suspend. Otherwise it will just go on looping. So add tests
against gspca_dev->frozen in the worker threads that need it.
Hdg, 2 minor changes:
1) The finepix device is ok with stopping reading a frame halfway through,
so add frozen checks in all places where we also check if we're still
streaming
2) Use gspca_dev->dev instead of gspca_dev->present to check for disconnect
in all touched drivers. I plan to do this everywhere in the future, and
most relevant lines in the touched drivers are already modified by this
patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add V4L2_CAP_DEVICE_CAPS support to querycap and replace -EINVAL by
-ENOTTY whenever an ioctl is not supported.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to support control event gspca has to use struct v4l2_fh.
As a bonus feature this also gives priority handling for free.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prepare for control events: free up file->private_data by using
video_drvdata(file) to get to the gspca_dev struct.
[mchehab@redhat.com: fix a compile error: ‘file’ undeclared]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the necessary changes to allow subdrivers to use the control framework.
This does not add control event support, that comes later.
It add a init_control cam_op that is called after init in probe that allows
the subdriver to set up the controls.
HdG: Call v4l2_ctrl_handler_setup from resume instead of
gspca_set_default_mode, as we just want to resend the current ctrl values to
the device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My last locking rework for pwc mistakenly assumed that videbuf2 does its
own locking, but it does not! This patch fixes the missing locking by
moving over the the video_device lock, and introducing a separate lock
for the videobuf2_queue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various error paths in fileio_init where not setting the request-count
to 0 when unrequesting the buffers on error to init the fileio emulation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This used to be the default if the lock pointer was set, but now that lock is by
default only used for ioctl serialization. Those drivers that already used
core locking have this flag set explicitly, except for some drivers where
it was obvious that there was no need to serialize any file operations other
than ioctl.
The drivers that didn't need this flag were:
drivers/media/radio/dsbr100.c
drivers/media/radio/radio-isa.c
drivers/media/radio/radio-keene.c
drivers/media/radio/radio-miropcm20.c
drivers/media/radio/radio-mr800.c
drivers/media/radio/radio-tea5764.c
drivers/media/radio/radio-timb.c
drivers/media/video/vivi.c
sound/i2c/other/tea575x-tuner.c
The other drivers that use core locking and where it was not immediately
obvious that this flag wasn't needed were changed so that the flag is set
together with a comment that that driver needs work to avoid having to
set that flag. This will often involve taking the core lock in the fops
themselves.
Eventually this flag should go and it should not be used in new drivers.
There are a few reasons why we want to avoid core locking of non-ioctl
fops: in the case of mmap this can lead to a deadlock in rare situations
since when mmap is called the mmap_sem is held and it is possible for
other parts of the code to take that lock as well (copy_from_user()/copy_to_user()
perform a down_read(&mm->mmap_sem) when a page fault occurs).
It is very unlikely that that happens since the core lock serializes all
fops, but the kernel warns about it if lock validation is turned on.
For poll it is also undesirable to take the core lock as that can introduce
increased latency. The same is true for read/write.
While it was possible to make flags or something to turn on/off taking the
core lock for each file operation, in practice it is much simpler to just
not take it at all except for ioctl and leave it to the driver to take the
lock. There are only a handful fops compared to the zillion ioctls we have.
I also wanted to make it obvious which drivers still take the lock for all
fops, so that's why I chose to have drivers set it explicitly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than checking the priority for each ioctl that needs to, just mark
such ioctls in the table and do it only once.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than testing whether an ioctl is implemented in the driver or not
every time the ioctl is called, do it upfront when the device is registered.
This also allows a driver to disable certain ioctls based on the capabilities
of the detected board, something you can't do today without creating separate
v4l2_ioctl_ops structs for each new variation.
For the most part it is pretty straightforward, but for control ioctls a flag
is needed since it is possible that you have per-filehandle controls, and that
can't be determined upfront of course.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using the V4L2 core lock is a very robust method that is usually very good
at doing the right thing. But some drivers, particularly USB drivers, may
want to prevent the core from taking the lock for specific ioctls, particularly
buffer queuing ioctls.
The reason is that certain commands like S_CTRL can take a long time to process
over USB and all the time the core has the lock, preventing VIDIOC_DQBUF from
proceeding, even though a frame may be ready in the queue.
This introduces unwanted latency.
Since the buffer queuing commands often have their own internal lock it is
often not necessary to take the core lock. Drivers can now say that they don't
want the core to take the lock for specific ioctls.
As it is a specific opt-out it makes it clear to the reviewer that those
ioctls will need more care when reviewing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add driver for SMIA++/SMIA image sensors. The driver exposes the sensor as
three subdevs, pixel array, binner and scaler --- in case the device has a
scaler.
Currently it relies on the board code for external clock handling. There is
no fast way out of this dependency before the ISP drivers (omap3isp) among
others will be able to export that clock through the clock framework
instead.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Perform CCDC link validation in ccdc_link_validate() instead of
isp_video_validate_pipeline(). Also perform maximum data rate check in
isp_video_check_external_subdevs().
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use default link validation for ccp2, csi2, preview and resizer. On ccp2,
csi2 and ccdc we also collect information on external subdevs as one may be
connected to those entities.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Access pipe->external_rate instead of isp_ccdc.vpcfg.pixelclk. Also remove
means to set the value for isp_ccdc_vpcfg.pixelclk.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
isp_video_check_external_subdevs() will retrieve external subdev's
bits-per-pixel and pixel rate for the use of other ISP subdevs at streamon
time. isp_video_check_external_subdevs() is called after pipeline
validation.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add pointer to external subdev, pixel rate of the external subdev and bpp of
the format to struct isp_pipeline.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Collect information on entities in pipeline in isp_video_far_end(), outside
pipeline validation. As this causes the function to have side effects,
rename the function accordingly.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add lane configuration (order of clock and data lane) to platform data on
both CCP2 and CSI-2.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since media_entity_pipeline_start() now does link validation, it may
actually fail. Perform the error handling.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The clock rate for l3_ick will soon be read during pipeline validation which
is now part of media_entity_pipeline_start(). For that reason we set
constraints earlier on.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
XCLK definitions are often required by the board code. Move them to public
include file.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow choosing the lock used by the control handler. This may be handy
sometimes when a driver providing multiple subdevs does not want to use
several locks to serialise its functions.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_subdev_link_validate() is the default op for validating a link. In V4L2
subdev context, it is used to call a pad op which performs the proper link
check without much extra work.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The purpose of the link_validate() op is to allow an entity driver to ensure
that the properties of the pads at the both ends of the link are suitable
for starting the pipeline. link_validate is called on sink pads on active
links which belong to the active part of the graph.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add control class for image processing controls. The control class deals
with controls processing image, for example digital gain or noise filtering,
which can be present in any part of the pipeline.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add image source control class. This control class is intended to contain
low level controls which deal with control of the image capture process ---
the A/D converter in image sensors, for example.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 uses the enum type in IOCTL arguments in IOCTLs that were defined until
the use of enum was considered less than ideal. Recently Rémi Denis-Courmont
brought up the issue by proposing a patch to convert the enums to unsigned:
<URL:http://www.spinics.net/lists/linux-media/msg46167.html>
This sparked a long discussion where another solution to the issue was
proposed: two sets of IOCTL structures, one with __u32 and the other with
enums, and conversion code between the two:
<URL:http://www.spinics.net/lists/linux-media/msg47168.html>
Both approaches implement a complete solution that resolves the problem. The
first one is simple but requires assuming enums and __u32 are the same in
size (so we won't break the ABI) while the second one is more complex and
less clean but does not require making that assumption.
The issue boils down to whether enums are fundamentally different from __u32
or not, and can the former be substituted by the latter. During the
discussion it was concluded that the __u32 has the same size as enums on all
archs Linux is supported: it has not been shown that replacing those enums
in IOCTL arguments would break neither source or binary compatibility. If no
such reason is found, just replacing the enums with __u32s is the way to go.
This is what this patch does. This patch is slightly different from Remi's
first RFC (link above): it uses __u32 instead of unsigned and also changes
the arguments of VIDIOC_G_PRIORITY and VIDIOC_S_PRIORITY.
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I applied the wrong version of Jiri's bonding fix in commit
13a8e0c8cd ("bonding: don't increase
rx_dropped after processing LACPDUs")
I applied v3, which introduces warnings I asked him to fix,
instead of v4 which properly takes care of those issues.
This inter-diffs such that the warnings are now gone.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk+vekgACgkQdwG7hYl686N8bQCfdizsFrliKbDW20R/pO66NoAV
aloAn0ln+mwe3rIdNt8qKynW8e8dbudF
=R7XS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd
Pull three MTD fixes from David Woodhouse:
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
* tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd:
mtd: ams-delta: fix request_mem_region() failure
jffs2: Fix lock acquisition order bug in gc path
mtd: fix oops in dataflash driver
An OMAP bug fix, a set of PCH bug fixes, and one patch to fix up compile
warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPra+FAAoJEEFnBt12D9kBW3oQALDLW0bneFl+sysynzu9qOAu
Qy4BmQjNalPHoZ3PZ6Q5CevrTXJsDwFxkKAS+29melBrPaKpubTPMoqD9yaTjizU
yH2MClTLIfOXOQTDwYyILeCq5jcw7uRAyx73cHzAD/JBCTkUgv8HoLKCbhZN4wo5
s/KqZRCEpee8rLHhQa7DFUuJVH7L9zskO2ZwpxgMGOAkDH4aB7OHzlcndB6jST4f
dFkMva50pQ8iggCu9tX/zmGbPXWKroSswnrdZVBOEKIj3QJq6h2B9s0u64B4ergZ
W57xnCF6AmPWp8YvenMruQRLUUy3KQIMZV5d8fIjvYXpH9TQJE4PR9IWjt+PADqy
TVoVR4tjcdYWFJuYhskpvT5dq/x2AX9eyNsTgu9ob8HyUQgzbcTu9zczUF52SiyN
ohqjrbKmPINnUrLD1gUkUmUayWt5SOt+hu19rMijqKY/HWQn2rzK5mUIreZeG/Cb
aPY1acunbdaNTsIgmIBqLkfSl/ErCYcXwmkulBIZOyUitaMYnZyhbZmgTIeEebTY
2ffX658MTT9cWlHsZ4wfWDynJIpsvTHCVau/oQfurLSO2p6Jb/xA7k34v9mxfAaK
gESiK+8T8n0u9RetLSSk7uKNyTqRvDaWsbaB7As0mAd1r8ETAL98N2ZzBv5o+bmF
JH4g4IgKNdowY4EqA0Ms
=P8v+
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull a few more GPIO bug fixes from Grant Likely:
"Oops, missed a couple. Here's an updated pull req for GPIO"
A set of PCH bug fixes, and one patch to fix up compile warnings
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPri7CAAoJEDeqqVYsXL0MOMYH/2vxI1NTdIvjApKiI6oumOS2
FjGqiUTsLXIR3pKoeZp12FdltC4zTVjDI/JBAvXfXWGy8ooaBceFiIiHesIucFBY
tBtgogKoq1vHk/spNNU3vGtpLDaDm9vqK9LACkwyUtF7IKUJYvmXmTq5Av0P27lE
ay+rpzLBLzJPATZjS94PKeXMOG7iDt+Idyh8Dp15kPUh5/kcUR40dzBhPmAeLEfQ
abshdAuMzBb7Dzb4tMfi/1AgISVgem9+fbzX/BjSGa0ByXr9/6VMgIhSdum7xxTp
3X1G6DR3km0SM1Lc5RJbujiG2lwP/l1lua5OreimMz78M5AUyPYnwYzq9CqGKQ4=
=GDPf
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor qla and virto fixes plus one major regression
fix (oops in all legacy host drivers)."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio_scsi: fix TMF use-after-free
[SCSI] fix oops in all legacy host adapters caused by 6f381fa
[SCSI] qla2xxx: Update version number to 8.04.00.03-k.
[SCSI] qla2xxx: Properly check for current state after the fabric-login request.
[SCSI] qla2xxx: Proper completion to scsi-ml for scsi status task_set_full and busy.
[SCSI] qla2xxx: Block flash access from application when device is initialized for ISP82xx.
[SCSI] qla2xxx: Fix reset time out as qla2xxx not ack to reset request.
Pull networking fixes from David S. Miller:
1) Since we do RCU lookups on ipv4 FIB entries, we have to test if the
entry is dead before returning it to our caller.
2) openvswitch locking and packet validation fixes from Ansis Atteka,
Jesse Gross, and Pravin B Shelar.
3) Fix PM resume locking in IGB driver, from Benjamin Poirier.
4) Fix VLAN header handling in vhost-net and macvtap, from Basil Gor.
5) Revert a bogus network namespace isolation change that was causing
regressions on S390 networking devices.
6) If bonding decides to process and handle a LACPDU frame, we
shouldn't bump the rx_dropped counter. From Jiri Bohac.
7) Fix mis-calculation of available TX space in r8169 driver when doing
TSO, which can lead to crashes and/or hung device. From Julien
Ducourthial.
8) SCTP does not validate cached routes properly in all cases, from
Nicolas Dichtel.
9) Link status interrupt needs to be handled in ks8851 driver, from
Stephen Boyd.
10) Use capable(), not cap_raised(), in connector/userns netlink code.
From Eric W. Biederman via Andrew Morton.
11) Fix pktgen OOPS on module unload, from Eric Dumazet.
12) iwlwifi under-estimates SKB truesizes, also from Eric Dumazet.
13) Cure division by zero in SFC driver, from Ben Hutchings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ks8851: Update link status during link change interrupt
macvtap: restore vlan header on user read
vhost-net: fix handle_rx buffer size
bonding: don't increase rx_dropped after processing LACPDUs
connector/userns: replace netlink uses of cap_raised() with capable()
sctp: check cached dst before using it
pktgen: fix crash at module unload
Revert "net: maintain namespace isolation between vlan and real device"
ehea: fix losing of NEQ events when one event occurred early
igb: fix rtnl race in PM resume path
ipv4: Do not use dead fib_info entries.
r8169: fix unsigned int wraparound with TSO
sfc: Fix division by zero when using one RX channel and no SR-IOV
openvswitch: Validation of IPv6 set port action uses IPv4 header
net: compare_ether_addr[_64bits]() has no ordering
cdc_ether: Ignore bogus union descriptor for RNDIS devices
bnx2x: bug fix when loading after SAN boot
e1000: Silence sparse warnings by correcting type
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
openvswitch: Release rtnl_lock if ovs_vport_cmd_build_info() failed.
...
Fix a couple of serious memory leaks in device-mapper thin provisioning
and tidy its MODULE_DESCRIPTION.
Mitigate occasional reported hangs associated with multipath scsi_dh
module loading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jmbP
-----END PGP SIGNATURE-----
Merge tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes from Alasdair G Kergon:
"Fix a couple of serious memory leaks in device-mapper thin
provisioning and tidy its MODULE_DESCRIPTION.
Mitigate occasional reported hangs associated with multipath scsi_dh
module loading."
* tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
If the requested scsi_dh module is already loaded then skip
request_module().
Multipath table loads can hang in an unnecessary __request_module.
Reported-by: Ben Marzinski <bmarzins@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix two places in commit 104655fd4d ("dm thin: support discards") that
didn't use pool->lock to protect against concurrent changes to the
prepared_discards list.
Without this fix, thin_endio() can race with process_discard(), leading
to concurrent list_add()s that result in the processes locking up with
an error like the following:
WARNING: at lib/list_debug.c:32 __list_add+0x8f/0xa0()
...
list_add corruption. next->prev should be prev (ffff880323b96140), but was ffff8801d2c48440. (next=ffff8801d2c485c0).
...
Pid: 17205, comm: kworker/u:1 Tainted: G W O 3.4.0-rc3.snitm+ #1
Call Trace:
[<ffffffff8103ca1f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8103cb16>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa04f6ce6>] ? bio_detain+0xc6/0x210 [dm_thin_pool]
[<ffffffff8124ff3f>] __list_add+0x8f/0xa0
[<ffffffffa04f70d2>] process_discard+0x2a2/0x2d0 [dm_thin_pool]
[<ffffffffa04f6a78>] ? remap_and_issue+0x38/0x50 [dm_thin_pool]
[<ffffffffa04f7c3b>] process_deferred_bios+0x7b/0x230 [dm_thin_pool]
[<ffffffffa04f7df0>] ? process_deferred_bios+0x230/0x230 [dm_thin_pool]
[<ffffffffa04f7e42>] do_worker+0x52/0x60 [dm_thin_pool]
[<ffffffff81056fa9>] process_one_work+0x129/0x450
[<ffffffff81059b9c>] worker_thread+0x17c/0x3c0
[<ffffffff81059a20>] ? manage_workers+0x120/0x120
[<ffffffff8105eabe>] kthread+0x9e/0xb0
[<ffffffff814ceda4>] kernel_thread_helper+0x4/0x10
[<ffffffff8105ea20>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff814ceda0>] ? gs_change+0x13/0x13
---[ end trace 7e0a523bc5e52692 ]---
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a significant memory leak inadvertently introduced during
simplification of cell_release_singleton() in commit
6f94a4c45a ("dm thin: fix stacked bi_next
usage").
A cell's hlist_del() must be accompanied by a mempool_free().
Use __cell_release() to do this, like before.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fixes the following compiler warnings:
drivers/gpio/gpio-samsung.c: In function ‘samsung_gpiolib_init’:
drivers/gpio/gpio-samsung.c:2980:1: warning: label ‘err_ioremap1’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2978:1: warning: label ‘err_ioremap2’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2976:1: warning: label ‘err_ioremap3’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2974:1: warning: label ‘err_ioremap4’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:55: warning: unused variable ‘gpio_base4’ [-Wunused-variable]
drivers/gpio/gpio-samsung.c:455:32: warning: ‘exynos_gpio_cfg’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2126:33: warning: ‘exynos4_gpios_1’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2228:33: warning: ‘exynos4_gpios_2’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2373:33: warning: ‘exynos4_gpios_3’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jean-Francois Dagenais reported:
Configuring a gpio pin with the gpio-pch driver with
"IRQF_TRIGGER_LOW | IRQF_ONESHOT" generates an interrupt storm for
threaded ISR until the ISR thread actually gets to physically clear
the interrupt on the triggering chip!! The immediate observable
symptom is the high CPU usage for my ISR thread task and the
interrupt count in /proc/interrupts incrementing radically.
The driver is wrong in several ways:
1) Using handle_simple_irq() does not provide proper flow control
handling. In the case of oneshot threaded handlers for the
demultiplexed interrupts this results in an interrupt storm because
the simple handler does not deal with masking/unmasking. Even
without threaded oneshot handlers an interrupt storm for level type
interrupts can easily be triggered when the interrupt is disabled
and the interrupt line is activated from the device.
2) Acknowlegding the demultiplexed interrupt before calling the
handler is wrong for level type interrupts.
3) The set_type function unconditionally enables the interrupt. It's
supposed to set the type and nothing else. The unmasking is done by
the core code.
Move the acknowledge code into a separate function and add it to the
demux irqchip callbacks.
Remove the unconditional enabling from the set_type() callback and set
the proper flow handlers depending on the selected type (level/edge).
Reported-and-tested-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull target fix from Nicholas Bellinger:
"This patch removes some incorrect legacy code to free se_lun_acl
memory in the NodeACL release path that could potentially trigger an
OOPS during shutdown once dynamic -> explicit initiator NodeACL
conversion has occurred.
That said, we've been able to trigger an OOPS in v4.0 code for this
special case when the associated MappedLUNs had not also been made
explicit based on active TPG LUN layout during the conversion, so it
really makes senses to go ahead and drop this extra cruft to avoid any
possible issues here.
This ends up only effecting iscsi-target module code (it's the only
user) and is CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect se_lun_acl release for dynamic -> explict ACL conversion
If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet vlan header is not on the packet and kept in the skb->vlan_tci
when it comes from lower dev. This patch inserts vlan header in user
buffer during skb copy on user read.
Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take vlan header length into account, when vlan id is stored as
vlan_tci. Otherwise tagged packets coming from macvtap will be
truncated.
Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some potentially problematic legacy code within
core_clear_initiator_node_from_tpg() that was originally intended to
release left over se_lun_acl setup during dynamic NodeACL+MappedLUN
generate when running with TPG demo-mode operation.
Since we now only ever expect to allocate and release se_lun_acl from
within target_core_fabric_configfs.c:target_fabric_make_mappedlun() and
target_fabric_drop_mappedlun() context respectively, this code for
demo-mode release is incorrect and needs to be removed.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER. As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.
Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2009 Philip Reiser notied that a few users of netlink connector
interface needed a capability check and added the idiom
cap_raised(nsp->eff_cap, CAP_SYS_ADMIN) to a few of them, on the premise
that netlink was asynchronous.
In 2011 Patrick McHardy noticed we were being silly because netlink is
synchronous and removed eff_cap from the netlink_skb_params and changed
the idiom to cap_raised(current_cap(), CAP_SYS_ADMIN).
Looking at those spots with a fresh eye we should be calling
capable(CAP_SYS_ADMIN). The only reason I can see for not calling capable
is that it once appeared we were not in the same task as the caller which
would have made calling capable() impossible.
In the initial user_namespace the only difference between between
cap_raised(current_cap(), CAP_SYS_ADMIN) and capable(CAP_SYS_ADMIN) are a
few sanity checks and the fact that capable(CAP_SYS_ADMIN) sets
PF_SUPERPRIV if we use the capability.
Since we are going to be using root privilege setting PF_SUPERPRIV seems
the right thing to do.
The motivation for this that patch is that in a child user namespace
cap_raised(current_cap(),...) tests your capabilities with respect to that
child user namespace not capabilities in the initial user namespace and
thus will allow processes that should be unprivielged to use the kernel
services that are only protected with cap_raised(current_cap(),..).
To fix possible user_namespace issues and to just clean up the code
replace cap_raised(current_cap(), CAP_SYS_ADMIN) with
capable(CAP_SYS_ADMIN).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8a83a00b07.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The NEQ interrupt is only triggered when there was no previous pending
interrupt. If we request irq handling after an interrupt has occurred,
we will never get an interrupt until we call H_RESET_EVENTS.
Events seem to be cleared when we first register the NEQ. So, when we
requested irq handling right after registering it, a possible race with
an interrupt was much less likely. Now, there is a chance we may lose
this race and never get any events.
The fix here is to poll and acknowledge any events that might have
happened right after registering the irq handler.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the caller (PM resume code) is not the one holding rtnl, when taking the
'else' branch rtnl may be released at any moment, thereby defeating the whole
purpose of this code block.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge PA-RISC compile fixes from Rolf Eike Beer:
"Since commit d66acc39c7 ("bitops: Optimise get_order()") getorder.h
includes log2.h which leads to an include loop on PA-RISC, bringing a
bunch of other breakage to light. This patchset fixes the compilation
of the current state of 3.4 on HPPA.
Unchanged against the first version, just added an Ack by Grant."
* emailed from Rolf Eike Beer <eike-kernel@sf-tec.de>: (5 patches)
parisc: move definition of PAGE0 to asm/page.h
parisc: add missing include of asm/page.h to asm/pgtable.h
parisc: drop include of asm/pdc.h from asm/hardware.h
parisc: add missing forward declarations in asm/hardware.h
parisc: add missing includes in asm/spinlock.h
This was defined in asm/pdc.h which needs to include asm/page.h for
__PAGE_OFFSET. This leads to an include loop so that page.h eventually will
include pdc.h again. While this is no problem because of header guards, it is
a problem because some symbols may be undefined. Such an error is this:
In file included from include/linux/bitops.h:35:0,
from include/asm-generic/getorder.h:7,
from arch/parisc/include/asm/page.h:162,
from arch/parisc/include/asm/pdc.h:346,
from arch/parisc/include/asm/processor.h:16,
from arch/parisc/include/asm/spinlock.h:6,
from arch/parisc/include/asm/atomic.h:20,
from include/linux/atomic.h:4,
from include/linux/sysfs.h:20,
from include/linux/kobject.h:21,
from include/linux/device.h:17,
from include/linux/eisa.h:5,
from arch/parisc/kernel/pci.c:11:
arch/parisc/include/asm/bitops.h: In function ‘set_bit’:
arch/parisc/include/asm/bitops.h:82:2: error: implicit declaration of function ‘_atomic_spin_lock_irqsave’ [-Werror=implicit-function-declaration]
arch/parisc/include/asm/bitops.h:84:2: error: implicit declaration of function ‘_atomic_spin_unlock_irqrestore’ [-Werror=implicit-function-declaration]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__devexit functions are discarded without CONFIG_HOTPLUG, so they need
to be referenced carefully. A __devexit function may also not be called
from a __devinit function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initialization of irqenable, irqstatus registers is the common
operation done in this function for all OMAP platforms, viz. OMAP1,
OMAP2+. The latter _gpio_rmw()'s which supposedly got introduced
wrongly to take care of OMAP2+ platforms were overwriting initially
programmed OMAP1 value breaking functionality on OMAP1.
Somehow incorrect assumption was made that each _gpio_rmw()'s were
mutually exclusive. On close observation it is found that the first
_gpio_rmw() which is supposedly done to take care of OMAP1 platform
is generic enough and takes care of OMAP2+ platform as well.
Therefore remove the latter _gpio_rmw() to irqenable as they are
redundant now.
Writing to ctrl and debounce_en registers for OMAP2+ platforms are
modified to match the original(pre-cleanup) code where the registers
are initialized with 0. In the cleanup series since we are using
_gpio_rmw(reg, 0, 1), instead of __raw_writel(), we are just reading
and writing the same values to ctrl and debounce_en. This is not an
issue for debounce_en register because it has 0x0 as the default value.
But in the case of ctrl register the default value is 0x2 (GATINGRATIO
= 0x1) so that we end up writing 0x2 instead of intended 0 value.
Therefore changing back to __raw_writel() as this is sufficient for
this case besides simpler to understand.
Also, change irqstatus initalization logic that avoids comparison
with bool, besides making it fit in a single line.
Cc: stable@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix a use-after-free in the TMF path, where cmd may have been already
freed by virtscsi_complete_free when wait_for_completion restarts
executing virtscsi_tmf. Technically a race, but in practice the command
will always be freed long before the completion waiter is awoken.
The fix is to make callers specifying a completion responsible for
freeing the command in all cases.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 6f381fa344
Author: Lin Ming <ming.m.lin@intel.com>
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
Caused a regression where we oops in every legacy mode SCSI host driver
because they supply a NULL pointer to scsi_add_host(). Fix this by checking
for the NULL in scsi_add_host_with_dma() and changing the DMA device to being
the platform_bus in that case (which replicates the original behaviour).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmmware detected under-run condition and scsi status of
task_set_full or busy_condition, return that to the mid layer for proper error
handling instead of DID_ERROR (which causes error handler activation and a
full retry).
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a last minute bug fix that was only just noticed since the code
path that's being exercised here is one that is fairly rarely used. The
changelog for the change itself is extremely clear and the code itself
is obvious to inspection so should be pretty safe.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPqoQhAAoJEBus8iNuMP3dj1kP/0Z1yIk1ME0KzSy42/qbGKsp
+2mrAASkh7DbbWU2hSmwTpEgAAiY2ws0A/Uyj/Al4f/gJW6bZvlxK4mbf1i+P1LG
ab3ohhUOqexHVaIKMTnYKhnHWuzU25mnf2vW8IOr6jccu6h7X4orDmw1uEPVgsbs
P7fThQa0BPRkiLIUWGmg0oMY6IXJlzsStDK2Npw47EypY4FZCZucJgXkmYZLt0Nk
mhLPsznD5GqHNSmCqrUI3j/s3R0sd/Xc63pvznBU9D8RAbSRgi2vGL8UenEtIQgt
bVXOKe5H8ZzXYNYpzpGeJm3dTE2pZWmT1hfRSf0kBOkLhEpt/Oy9WBj1kfoTg9n9
fNH6OJYn12uG0qQomiAT96Qm3qrslF5y9S64ZyHT6BAkJT87wnEqTmaQkoAevDEr
hldzT+dTPAk2Pspge8m910+kQA72YyE1z6/PikvkEepYDFrqffZcBFWqjW8aQjGj
/5r7F5fLC7zJku0FjYUMRYDgYc9z0lk6tDt8QL7E7j+55ntrhYR8IuTQA7g2asal
yeQSTqa/NkJcch+aULgyOU0W9U1z2i04mdGI74iJnf3DSGGmvJ95IYLJA4tfnIOw
63xo2BhmHVGyRqTN5l7o5Zlgf5FdcUt+5EBLudSqqZynB/tMZNgb0PEzfIRFBuRq
GSIm5dwIqKgtymCEOUmp
=xcal
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull last minute regman bug fix from Mark Brown:
"This is a last minute bug fix that was only just noticed since the
code path that's being exercised here is one that is fairly rarely
used. The changelog for the change itself is extremely clear and the
code itself is obvious to inspection so should be pretty safe."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix possible memory corruption in regmap_bulk_read()
The function regmap_bulk_read() calls the regmap_read() for
each register if set of register has volatile and cache is
enabled. In this case, last few register read makes the memory
corruption if the register size is not the size of unsigned int.
The regam_read() takes argument as unsigned int for returning
value and it update the value as
*val = map->format.parse_val(map->work_buf);
This causes complete 4 bytes (size of unsigned int) to get written.
Now if client pass the memory pointer for value which is equal to the
required size of register count in regmap_bulk_read() then last few
register read actually update the memory beyond passed pointer size.
Avoid this by using local variable for read and then do memcpy()
for actual byte copy to passed pointer based on register size.
I allocated one pointer ptr and take first 16 bytes dump of that
pointer then call regmap_bulk_read() with pointer which is just
on top of this allocated pointer and register count of 128. Here
register size is 1 byte.
The memory trace of last 5 register read are as follows:
[ 5.438589] regmap_bulk_read after regamp_read() for register 122
[ 5.447421] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.467535] regmap_bulk_read after regamp_read() for register 123
[ 5.476374] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.496425] regmap_bulk_read after regamp_read() for register 124
[ 5.505260] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.525372] regmap_bulk_read after regamp_read() for register 125
[ 5.534205] 0xef993c00 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 126
[ 5.563100] 0xef990000 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 127
[ 5.587108] 0xef000000 0xef993c00 0x00000000 0x00000001
Here it is observed that the memory content at first word started changing
on last 3 regmap_read() and so corruption happened.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The r8169 may get stuck or show bad behaviour after activating TSO :
the net_device is not stopped when it has no more TX descriptors.
This problem comes from TX_BUFS_AVAIL which may reach -1 when all
transmit descriptors are in use. The patch simply tries to keep positive
values.
Tested with 8111d(onboard) on a D510MO, and with 8111e(onboard) on a
Zotac 890GXITX.
Signed-off-by: Julien Ducourthial <jducourt@free.fr>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to request_mem_region() has been introduced in the omap-gpio
driver recently (commit 96751fcbe5,
"gpio/omap: Use devm_ API and add request_mem_region"). This change
prevented the Amstrad Delta NAND driver, which was doing the same in
order to take control over OMAP MPU I/O lines that the NAND device hangs
off, from loading successfully.
The I/O lines and corresponding registers used by the NAND driver are a
subset of those used for the GPIO function. Then, to avoid run time
collisions, all MPUIO GPIO lines should be marked as requested while
initializing the NAND driver, and vice versa, a single MPUIO GPIO line
already requested before the NAND driver initialization is attempted
should prevent the NAND device from being started successfully.
There is another driver, omap-keypad, which also manipulates MPUIO
registers, but has never been calling request_mem_region() on startup,
so it's not affected by the change in the gpio-omap and works correctly.
It uses the depreciated omap_read/write functions for accessing MPUIO
registers. Unlike the NAND driver, these I/O lines and registers are
separate from those used by the GPIO driver. However, both register sets
are non-contiguous and overlapping, so it would be impractical to
request the two sets separately, one from the gpio-omap, the other form
the omap-keypad driver.
In order to solve all these issues correctly, a solution first suggested
by Artem Bityutskiy, then closer specified by Tony Lindgren while they
commented the initial version of this fix, should be implemented. The
gpio-omap driver should export a few functions which would allow the
other two drivers to access MPUIO registers in a safe manner instead of
trying to manage them in parallel to the GPIO driver. However, such a
big change, affecting 3 drivers all together, is not suitable for the rc
cycle, and should be prepared for the merge window. Then, an
alternative solution is proposed as a regression fix.
For the ams-delta NAND driver to initialize correctly in coexistence
with the changed GPIO driver, drop the request_mem_region() call from
the former, especially as this call is going to be removed while the
long-term solution is implemented.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
One small fix for an edge condition in the max8997 driver and a fix for
a surprise in the devres API which caused devm_regulator_put() to not
actually put the regulator - a nicer version of this based on an
improvement of the devres API is queued for 3.5.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Q7eh
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One small fix for an edge condition in the max8997 driver and a fix
for a surprise in the devres API which caused devm_regulator_put() to
not actually put the regulator - a nicer version of this based on an
improvement of the devres API is queued for 3.5."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Actually free the regulator in devm_regulator_put()
regulator: Fix the logic to ensure new voltage setting in valid range
Pull drm fixes from Dave Airlie:
"Two fixes from Intel, one a regression, one because I merged an early
version of a fix.
Also the nouveau revert of the i2c code that was tested on the list."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/i2c: resume use of i2c-algo-bit, rather than custom stack
drm/i915: Do no set Stencil Cache eviction LRA w/a on gen7+
drm/i915: disable sdvo hotplug on i945g/gm
* fix to Kconfig to make it fit within 80 line characters,
* two bootup fixes (AMD 8-core and with PCI BIOS),
* cleanup code in a Xen PV fb driver,
* and a crash fix when trying to see non-existent PTE's
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPp/iaAAoJEFjIrFwIi8fJAFsH/1NVxvOAHyzyczU49U/1vi8T
d67kIb8fFHni6HO7BiBkuM8DricGQnDhP7uC1n9waWf8jRiYsPTAbesyedTLbQos
SLfzpsLWKilJOxWCf17cBnm6i9ScQn1ioJ6h3jFzHgNCXnvvAVYqfKHW0V6HTErH
JL0eb4+asiZgXNSeac1gabQlai6LuBzMWaFgzRGY+hDnCQhkdQfDkD7X5zEhUUmH
jUmtSxRx+5LkfelwRb2kHhI5j58ilOEa7YLZFQc3C+2+bUvgsG9vJDsQ3jwFaGDn
cryfRY9WJXxgcXqk1ClOnk9U9PGzRc48gdLVLhYuLsIvUWN7RzgRlBMsH33Gq9M=
=kjvX
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
- fix to Kconfig to make it fit within 80 line characters,
- two bootup fixes (AMD 8-core and with PCI BIOS),
- cleanup code in a Xen PV fb driver,
- and a crash fix when trying to see non-existent PTE's
* tag 'stable/for-linus-3.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/Kconfig: fix Kconfig layout
xen/pci: don't use PCI BIOS service for configuration space accesses
xen/pte: Fix crashes when trying to see non-existent PGD/PMD/PUD/PTEs
xen/apic: Return the APIC ID (and version) for CPU 0.
drivers/video/xen-fbfront.c: add missing cleanup code
The function vb2_dma_contig_vaddr returns a void * not an integer.
Quiets the sparse noise:
warning: Using plain integer as NULL pointer
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Include the header to pickup the definitions of the exported symbols.
Quiets the following sparse warnings:
warning: symbol 'vb2_dma_contig_memops' was not declared. Should it be static?
warning: symbol 'vb2_dma_contig_init_ctx' was not declared. Should it be static?
warning: symbol 'vb2_dma_contig_cleanup_ctx' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no needs to keep .remove under .exit.text. This driver is for a
standalone chip that could be on any board and connected to any i2c bus.
At the same time we don't need to keep the as3645a_probe() after initializing
the device. Therefore we mark it and relevant functions with __devinit tag.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mf_low value must be a multiple of mf_inc. Round it up to the
nearest mf_inc multiple after computing it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If RSS is disabled on the PF (efx->n_rx_channels == 1) we try to set
up the indirection table so that VFs can use it, setting
efx->rss_spread = efx_vf_size(efx). But if SR-IOV was disabled at
compile time, this evaluates to 0 and we end up dividing by zero when
initialising the table.
I considered changing the fallback definition of efx_vf_size() to
return 1, but its value is really meaningless if we are not going to
enable VFs. Therefore add a condition of efx_sriov_wanted(efx) in
efx_probe_interrupts().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Support for the legacy crop API is emulated in the subdev core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for the legacy crop API is emulated in the subdev core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Configure CFA interpolation automatically based on the input format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For consistency reasons, rename the last remaining occurences of
rgb_to_ycbcr to csc (color space conversion).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When applications modify preview engine parameters, the new values are
applied to the hardware by the preview engine interrupt handler during
vertical blanking. If the parameters are being changed when the
interrupt handler is called, it just delays applying the parameters
until the next frame.
If an application modifies the parameters for every frame, and the
preview engine interrupt is triggerred synchronously, the parameters are
never applied to the hardware.
Fix this by storing new parameters in a shadow copy, and switch the
active parameters with the shadow values atomically.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using a large switch/case statement to return offsets to and
sizes of individual preview engine parameters in the parameters and
configuration structures, store the information in the update_attrs
table and use it at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the blk_adj and rgb2ycbcr fields to blkadj and csc respectively.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The feature_bit is always equal to 1 << array position, remove it and
compute the value dynamically.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The preview engine parameters are referenced by a value suitable for
being used in a bitmask. Two macros named OMAP3ISP_PREV_* and PREV_* are
declared for each parameter and are used interchangeably. Remove the
private macro.
Replace the configuration bit field in the parameter update attributes
structure with a boolean that indicates whether the parameter can be
updated through the preview engine configuration ioctl.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The flag isn't used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
