Couple of '_ATTR's were missing and SEC_CHAN_OFFSET to CHANNEL_TYPE
rename was missed in couple of places.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add initial support for libertas devices using a GSPI interface. This has
been tested with the 8686.
GSPI is intended to be used on embedded systems. Board-specific parameters are
required (see libertas_spi.h).
Thanks to everyone who took a look at the earlier versions of the patch.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For any callbacks in ieee80211_ops, specify what values the return
codes represent. While at it, fix a couple of capitalization and
punctuation differences.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows user space to determine whether a driver supports MFP and
behave properly without having to ask user to configure this in
MFP-optional mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If driver/firmware/hardware does not support CCMP for management
frames, it can now request mac80211 to take care of encrypting and
decrypting management frames (when MFP is enabled) in software. The
will need to add this new IEEE80211_KEY_FLAG_SW_MGMT flag when a CCMP
key is being configured for TX side and return the undecrypted frames
on RX side without RX_FLAG_DECRYPTED flag to use software CCMP for
management frames (but hardware for data frames).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When MFP is enabled, the AP does not allow a STA to associate if an
existing security association exists without first going through SA
Query process. When this happens, the association request is denied
with a new status code ("temporarily rejected") ans Association
Comeback IE is used to notify when the association may be tried again
(i.e., when the SA Query procedure has timed out).
Use the comeback time to update the mac80211 client MLME timer for
next association attempt to minimize waiting time if association is
temporarily rejected.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process SA Query Requests for client mode in mac80211. AP side
processing of SA Query Response frames is in user space (hostapd).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new WEXT IW_AUTH_* parameter for setting MFP
disabled/optional/required.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added new SIOCSIWENCODEEXT algorithm for configuring BIP (AES-CMAC)
keys (IGTK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new IW_AUTH parameter for setting cipher suite for
multicast/broadcast management frames. This is for full-mac drivers
that take care of RSN IE generation for (re)association request frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement Broadcast/Multicast Integrity Protocol for management frame
protection. This patch adds the needed definitions for the new
information element (MMIE) and implementation for the new "encryption"
type (though, BIP is actually not encrypting data, it provides only
integrity protection). These routines will be used by a follow-on patch
that enables BIP for multicast/broadcast robust management frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend CCMP to support encryption and decryption of unicast management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add flags for setting STA entries and struct ieee80211_if_sta to
indicate whether management frame protection (MFP) is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add support for multiple drivers to provide a regulatory_hint()
on a system by adding a wiphy specific regulatory domain cache.
This allows drivers to keep around cache their own regulatory domain
structure queried from CRDA.
We handle conflicts by intersecting multiple regulatory domains,
each driver will stick to its own regulatory domain though unless
a country IE has been received and processed.
If the user already requested a regulatory domain and a driver
requests the same regulatory domain then simply copy to the
driver's regd the same regulatory domain and do not call
CRDA, do not collect $200.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies hardware flags for powersave to support three different
flags:
* IEEE80211_HW_SUPPORTS_PS - indicates general PS support
* IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
* IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device
It also adds documentation for all this which explains how to set the
various flags.
Additionally, it fixes a few things:
* a spot where && was used to test flags
* enable CONF_PS only when associated again
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be needed for drivers that set the
IEEE80211_HW_NO_STACK_DYNAMIC_PS flag and still
want to handle dynamic PS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel_type really doesn't need to be the only member in
a new structure, so remove the struct. Additionally, remove
the _CONF_CHANGE_HT flag and use _CONF_CHANGE_CHANNEL when the
channel type changes, since that's enough of a change to require
reprogramming the hardware anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I missed this during review of "mac80211: Fix tx power setting",
the user_power_level shouldn't be available to the driver but
rather be an internal value used to calculate the value for the
driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add vendor ID for Foxconn and use it to set the ath5k LED gpio and
polarity for Acer branded laptops.
base.c:
Changes-licensed-under: 3-Clause-BSD
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The set_key callback now seems rather odd, passing a MAC address
instead of a station struct, and a local address instead of a
vif struct. Change that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k]
Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00]
Acked-by: Christian Lamparter <chunkeey@web.de> [p54]
Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945]
Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds detection code for the LP-PHY and SPROM
extraction code for version 8, which is needed by the LP-PHY and
newer N-PHY.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
power_level in ieee80211_conf is being used for more than one
purpose. It being used as user configured power limit and the
final power limit given to the driver. By doing so, except very
first time, the tx power limit is taken from min(chan->max_power,
local->hw.conf.power_level) which is not what we want. This patch
defines a new memeber in ieee80211_conf which is meant only for
user configured power limit.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can simply use conf_is_ht() check where needed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In HT capable drivers you often need to check if you
are currently using HT20 or HT40. This adds a few small
helpers to let drivers figure that out.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added mappings for FHSS, DSSS and OFDM channels - with macros to point
HR DSSS and ERP to the DSSS mappings. Currently just static inline
functions.
Use the new functions in the older fullmac drivers. This eliminates a
number of const static buffers and removes a couple of range checks that
are now redundant.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Richard Farina <sidhayn@gmail.com>
Acked-by: Jeroen Vreeken <pe1rxq@amsat.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Warn on deprecated binding model use
eeprom: More consistent symbol names
eeprom: Move 93cx6 eeprom driver to /drivers/misc/eeprom
spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
i2c: Move old eeprom driver to /drivers/misc/eeprom
i2c: Move at24 to drivers/misc/eeprom
i2c: Quilt tree has moved
i2c: Delete many unused adapter IDs
i2c: Delete 10 unused driver IDs
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (92 commits)
gianfar: Revive VLAN support
vlan: Export symbols as non GPL symbols.
bnx2x: tx_has_work should not wait for FW
netxen: reduce memory footprint
netxen: fix vlan tso/checksum offload
net: Fix linux/if_frad.h's suitability for userspace.
net: Move config NET_NS to from net/Kconfig to init/Kconfig
isdn: Fix missing ifdef in isdn_ppp
networking: document "nc" in addition to "netcat" in netconsole.txt
e1000e: workaround hw errata
af_key: initialize xfrm encap_oa
virtio_net: Fix MAX_PACKET_LEN to support 802.1Q VLANs
lcs: fix compilation for !CONFIG_IP_MULTICAST
rtl8187: Add termination packet to prevent stall
iwlwifi: fix rs_get_rate WARN_ON()
p54usb: fix packet loss with first generation devices
sctp: Fix another socket race during accept/peeloff
sctp: Properly timestamp outgoing data chunks for rtx purposes
sctp: Correctly start rtx timer on new packet transmissions.
sctp: Fix crc32c calculations on big-endian arhes.
...
The userspace interfaces are protected by CONFIG_* ifdefs
and that of course can't work.
Reported by Jaswinder Singh Rajput.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the kernel developers know that i2c_attach_client() and
i2c_detach_client() are deprecated and should no longer be used.
Drivers using these should be converted to the standard device
driver binding model (probe and remove methods.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
klist.c: bit 0 in pointer can't be used as flag
debugfs: introduce stub for debugfs_create_size_t() when DEBUG_FS=n
sysfs: fix problems with binary files
PNP: fix broken pnp lowercasing for acpi module aliases
driver core: Convert '/' to '!' in dev_set_name()
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix cursor physical address choice to match the 2D driver.
drm: stash AGP include under the do-we-have-AGP ifdef
drm: don't whine about not reading EDID data
drm/i915: hook up LVDS DPMS property
drm/i915: remove unnecessary debug output in KMS init
i915: fix freeing path for gem phys objects.
drm: create mode_config idr lock
drm: fix leak of device mappings since multi-master changes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: fix lock imbalance in pciehp
PCI PM: Restore standard config registers of all devices early
PCI/MSI: bugfix/utilize for msi_capability_init()
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
i.MX31: framebuffer driver
i.MX31: Image Processing Unit DMA and IRQ drivers
dmaengine: add async_tx_clear_ack() macro
dmaengine: dma_issue_pending_all == nop when CONFIG_DMA_ENGINE=n
dmaengine: kill some dubious WARN_ONCEs
fsldma: print correct IRQ on mpc83xx
fsldma: check for NO_IRQ in fsl_dma_chan_remove()
dmatest: Use custom map/unmap for destination buffer
fsldma: use a valid 'device' for dma_pool_create
dmaengine: fix dependency chaining
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: add and use INIT_WORK_ON_STACK
rcu: remove duplicate CONFIG_RCU_CPU_STALL_DETECTOR
relay: fix lock imbalance in relay_late_setup_files
oprofile: fix uninitialized use of struct op_entry
rcu: move Kconfig menu
softlock: fix false panic which can occur if softlockup_thresh is reduced
rcu: add __cpuinit to rcu_init_percpu_data()
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimers: fix inconsistent lock state on resume in hres_timers_resume
time-sched.c: tick_nohz_update_jiffies should be static
locking, hpet: annotate false positive warning
kernel/fork.c: unused variable 'ret'
itimers: remove the per-cpu-ish-ness
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
xen: unitialised return value in xenbus_write_transaction
x86: fix section mismatch warning
x86: unmask CPUID levels on Intel CPUs, fix
x86: work around PAGE_KERNEL_WC not getting WC in iomap_atomic_prot_pfn.
x86: use standard PIT frequency
xen: handle highmem pages correctly when shrinking a domain
x86, mm: fix pte_free()
xen: actually release memory when shrinking domain
x86: unmask CPUID levels on Intel CPUs
x86: add MSR_IA32_MISC_ENABLE bits to <asm/msr-index.h>
x86: fix PTE corruption issue while mapping RAM using /dev/mem
x86: mtrr fix debug boot parameter
x86: fix page attribute corruption with cpa()
Revert "x86: signal: change type of paramter for sys_rt_sigreturn()"
x86: use early clobbers in usercopy*.c
x86: remove kernel_physical_mapping_init() from init section
fix: crash: IP: __bitmap_intersects+0x48/0x73
cpufreq: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
work_on_cpu: Use our own workqueue.
work_on_cpu: don't try to get_online_cpus() in work_on_cpu.
...
Reported by Stephen Rothwell.
Due to missing 'extern' in the com20020_netdev_ops declaration,
each file that includes linux/com20020.h gets another copy
defined in it's resulting object file.
Signed-off-by: David S. Miller <davem@davemloft.net>
crc32c algorithm provides a byteswaped result. On little-endian
arches, the result ends up in big-endian/network byte order.
On big-endinan arches, the result ends up in little-endian
order and needs to be byte swapped again. Thus calling cpu_to_le32
gives the right output.
Tested-by: Jukka Taimisto <jukka.taimisto@mail.suomi.net>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This last patch makes the appropriate changes to use and propagate the
network namespace where needed in IPv4 multicast routing code.
This consists mainly in replacing all the remaining init_net occurences
with current netns pointer retrieved from sockets, net devices or
mfc_caches depending on the routines' contexts.
Some routines receive a new 'struct net' parameter to propagate the current
netns:
* vif_add/vif_delete
* ipmr_new_tunnel
* mroute_clean_tables
* ipmr_cache_find
* ipmr_cache_report
* ipmr_cache_unresolved
* ipmr_mfc_add/ipmr_mfc_delete
* ipmr_get_route
* rt_fill_info (in route.c)
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
