Fix NULL-pointer dereferences on open() and write() which can be
triggered by a malicious USB device.
The current URB allocation helper would fail to initialise the newly
allocated URB if the device has unexpected endpoint descriptors,
something which could lead NULL-pointer dereferences in a number of
open() and write() paths when accessing the URB. For example:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:usb_clear_halt+0x11/0xc0
...
Call Trace:
? tty_port_open+0x4d/0xd0
keyspan_open+0x70/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:keyspan_write+0x14e/0x1f3 [keyspan]
...
Call Trace:
serial_write+0x43/0xa0 [usbserial]
n_tty_write+0x1af/0x4f0
? do_wait_intr_irq+0x80/0x80
? process_echoes+0x60/0x60
tty_write+0x13f/0x2f0
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:keyspan_usa26_send_setup+0x298/0x305 [keyspan]
...
Call Trace:
keyspan_open+0x10f/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
Fixes: fdcba53e2d ("fix for bugzilla #7544 (keyspan USB-to-serial converter)")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Enable support for cbus gpios on FT232H. The cbus configuration is
stored in two words in the EEPROM at byte-offset 0x1a with the mux
config for ACBUS5, ACBUS6, ACBUS8 and ACBUS9 (only pins that can be
configured as I/O mode).
Tested using FT232H by configuring one ACBUS pin at a time.
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Matthew Michilot <matthew.michilot@gmail.com>
[ johan: fix copy-paste error in commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=2a70 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
In 22b8:900e "qc_dload" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=900e Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
And in 22b8:4281 "ram_downloader" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=4281 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Lars Melin <larsm17@gmail.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are the USB-serial updates for 5.3-rc1; just some new device ids
this time.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXRxL/gAKCRALxc3C7H1l
CKHnAQDsaOTD7f5Rhn2x0VapiuuxC3BcSHDgizmPcIt2f8F1yQEAgLvMy1//N75O
XTG6rLe6EsYc/fHj3csdgCURSMZVzQw=
=wAe3
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.3-rc1
Here are the USB-serial updates for 5.3-rc1; just some new device ids
this time.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for isodebug v1
USB: serial: option: add support for GosunCn ME3630 RNDIS mode
This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the
second channel is available for use as a serial port.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@unjo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
While there are a mix of things here, most of the stuff
were written from Kernel developer's PoV. So, add them to
the driver-api book.
A follow up for this patch would be to move documents from
there that are specific to sysadmins, adding them to the
admin-guide.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for Telit LE910Cx 0x1260 and 0x1261 compositions.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is adds the vendor and device id for the AT-VT-Kit3 which is a
pl2303-based device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Implement Fintek F81232 break on/off with LCR register.
It's the same with 16550A LCR register layout.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: fix corrupt line settings on break due to missing shadow_lcr
update in set_termios() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81232 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.
F81232 Clock registers (106h)
Bit1-0: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81232 will report data and LSR with bulk like following format:
bulk-in data: [LSR(1Byte)+DATA(1Byte)][LSR(1Byte)+DATA(1Byte)]...
LSR will auto clear frame/parity/break error flag when reading by H/W,
but overrrun will only cleared when reading LSR. So this patch add a
worker to read LSR when overrun and flush the worker on close() &
suspend().
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81232 will use interrupt worker to handle MSR change.
This patch will fix the issue that interrupt work should stop
in close() and suspend().
This also fixes line-status events being disabled after a suspend cycle
until the port is re-opened.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: amend commit message ]
Fixes: 87fe5adcd8 ("USB: f81232: implement read IIR/MSR with endpoint")
Cc: stable <stable@vger.kernel.org> # 4.1
Signed-off-by: Johan Hovold <johan@kernel.org>
Gustavo has been working to fix up all of the switch statements that
"fall through" such that we can eventually turn on
-Wimplicit-fallthrough. As part of that, the io_edgeport.c driver is a
bit "messy" with the parsing logic of a data packet. Clean that logic
up a bit by unindenting one level of the logic, and properly label
/* Fall through */ to make gcc happy.
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the throttle implementation by dropping the redundant
throttle_req flag which was a remnant from back when there was only a
single read URB.
Also convert the throttled flag to an atomic bit flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().
First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.
CPU 1 CPU 2
================ ================
complete() unthrottle()
process_urb();
smp_mb__before_atomic();
set_bit(i, free); if (test_and_clear_bit(i, free))
submit_urb();
Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.
CPU 1 CPU 2
================ ================
complete() unthrottle()
set_bit(i, free); throttled = 0;
smp_mb__after_atomic(); smp_mb();
if (throttled) if (test_and_clear_bit(i, free))
return; submit_urb();
Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.
Fixes: d83b405383 ("USB: serial: add support for multiple read urbs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Override the initial terminal settings provided by core directly instead
of first resetting them to tty_std_termios.
Also reorder the cflags as they are usually seen (in bit order).
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop bogus TIOCM_CTS, which is not a cflag, from the initial terminal
settings.
Note that the corresponding bit is already set by CS8.
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that init_termios() is only called on first use, we can clean up the
cypress_m8 initial-termios handling.
Note that only the earthmate chip type used settings different from the
defaults provided by USB serial core, and that the chip type is indeed
known when init_termios is called at tty-install time.
Signed-off-by: Johan Hovold <johan@kernel.org>
The initial terminal settings set by the driver matches the default
settings provided by core so drop the redundant init_termios callback.
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB-serial driver init_termios callback is used to override the
default initial terminal settings provided by USB-serial core.
After a bug was fixed in the original implementation introduced by
commit fe1ae7fdd2 ("tty: USB serial termios bits"), the init_termios
callback was no longer called just once on first use as intended but
rather on every (first) open.
This specifically meant that the terminal settings saved on (final)
close were ignored when reopening a port for drivers overriding the
initial settings.
Also update the outdated function header referring to the creation of
termios objects.
Fixes: 7e29bb4b77 ("usb-serial: fix termios initialization logic")
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up set_termios() by adding missing white space around operators
and making a couple of continuation lines more readable.
Also drop a couple of redundant braces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up modem-control handling somewhat by adding missing whitespace
around operators and splitting a long statement in two.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add helper function to update register bits instead of overwriting the
entire control register when updating the flow-control settings.
This specifically avoids having the tranceiver suspend mode (bit 0)
depend on the flow control setting.
The tranceiver is currently configured at probe to be disabled during
suspend, but this was overridden when disabling flow control or enabling
xon/xoff.
Fixes: 715f9527c1 ("USB: flow control fix for pl2303")
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Older pl2303 devices do not support automatic xon/xoff flow control, so
add add a flag to prevent trying to enable it for legacy device types.
Refactor the IXON test into a helper function to improve readability.
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
Reported-by: Uli <t9cpu@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com>
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Fixes: ec0cd94d88 ("usb: option: add SIMCom SIM5218")
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7PogAKCRALxc3C7H1l
CLtbAP9N7qnHiOflSg8sK3E4hBI5ZaVKQuJwObEOMJY+s6jeYwD1E3sbyWKGHu+2
R8Px/FbKC3JWMUIhO7bVlyvsQDcQAA==
=hG64
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for 5.1-rc1
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485
USB: serial: cp210x: add ID for Ingenico 3070
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7M3AAKCRALxc3C7H1l
CBUpAQD/N1G1G38alGS0zwn/u9krsVyLm5Y1gK8MWXvpkcGBXwEAoSYrMjoRAAdR
Ks4rQdSyYonbE3zENXp5d3beCRM4pQY=
=GQ5N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.1-rc1
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit ME910 ECM composition
USB: serial: cp210x: fix GPIO in autosuspend
USB: serial: cp210x: add minimum baud rate for CP2105 SCI
USB: serial: cp210x: add GPIO support for CP2104
USB: serial: cp210x: support all gpios on CP2102N QFN28 package
Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
Fixes: cf5276ce78 ("USB: serial: cp210x: Adding GPIO support for CP2105")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds the USB ID of the Hjelmslund Electronics USB485 Iso stick.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is how this device appears in kernel log:
usb 3-1: new full-speed USB device number 18 using xhci_hcd
usb 3-1: New USB device found, idVendor=0b00, idProduct=3070
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1: Product: Ingenico 3070
usb 3-1: Manufacturer: Silicon Labs
usb 3-1: SerialNumber: 0001
Apparently this is a POS terminal with embedded USB-to-Serial converter.
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add minimum baud rate to the cp210x driver.
According to the datasheet for CP2105, the SCI supports 2400 as the
lowest baud rate. As this is not heeded in the current code, an error
message 'failed set req 0x1e size 4 status: -32' when trying to set a
lower baud rate such as 300.
The other cp210x models to date supports a minimum baud rate of 300.
Signed-off-by: Johanna Abrahamsson <johanna.abrahamsson@afconsult.com>
[ johan: simplify min_speed init, move clamp after comment, and drop
unused serial-data pointer from cp210x_get_actual_rate() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
