There is no hardware supporting ct helper offload. However, prior to this
patch, a flower filter with a helper in the ct action can be successfully
set into the HW, for example (eth1 is a bnxt NIC):
# tc qdisc add dev eth1 ingress_block 22 ingress
# tc filter add block 22 proto ip flower skip_sw ip_proto tcp \
dst_port 21 ct_state -trk action ct helper ipv4-tcp-ftp
# tc filter show dev eth1 ingress
filter block 22 protocol ip pref 49152 flower chain 0 handle 0x1
eth_type ipv4
ip_proto tcp
dst_port 21
ct_state -trk
skip_sw
in_hw in_hw_count 1 <----
action order 1: ct zone 0 helper ipv4-tcp-ftp pipe
index 2 ref 1 bind 1
used_hw_stats delayed
This might cause the flower filter not to work as expected in the HW.
This patch avoids this problem by simply returning -EOPNOTSUPP in
tcf_ct_offload_act_setup() to not allow to offload flows with a helper
in act_ct.
Fixes: a21b06e731 ("net: sched: add helper support in act_ct")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/f8685ec7702c4a448a1371a8b34b43217b583b9d.1699898008.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Referenced commit doesn't always set iifidx when offloading the flow to
hardware. Fix the following cases:
- nf_conn_act_ct_ext_fill() is called before extension is created with
nf_conn_act_ct_ext_add() in tcf_ct_act(). This can cause rule offload with
unspecified iifidx when connection is offloaded after only single
original-direction packet has been processed by tc data path. Always fill
the new nf_conn_act_ct_ext instance after creating it in
nf_conn_act_ct_ext_add().
- Offloading of unidirectional UDP NEW connections is now supported, but ct
flow iifidx field is not updated when connection is promoted to
bidirectional which can result reply-direction iifidx to be zero when
refreshing the connection. Fill in the extension and update flow iifidx
before calling flow_offload_refresh().
Fixes: 9795ded7f9 ("net/sched: act_ct: Fill offloading tuple iifidx")
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 6a9bad0069 ("net/sched: act_ct: offload UDP NEW connections")
Link: https://lore.kernel.org/r/20231103151410.764271-1-vladbu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I am looking at syzbot reports triggering kernel stack overflows
involving a cascade of ipvlan devices.
We can save 8 bytes in struct flowi_common.
This patch alone will not fix the issue, but is a start.
Fixes: 24ba14406c ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: wenxu <wenxu@ucloud.cn>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20231025141037.3448203-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- Support GRO decapsulation for IPsec ESP in UDP.
- Add a handful of MODULE_DESCRIPTION()s.
- Drop questionable alignment check in TCP AO to avoid
build issue after changes in the crypto tree.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=fqHj
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.7-followup' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull more networking updates from Jakub Kicinski:
- Support GRO decapsulation for IPsec ESP in UDP
- Add a handful of MODULE_DESCRIPTION()s
- Drop questionable alignment check in TCP AO to avoid
build issue after changes in the crypto tree
* tag 'net-next-6.7-followup' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next:
net: tcp: remove call to obsolete crypto_ahash_alignmask()
net: fill in MODULE_DESCRIPTION()s under drivers/net/
net: fill in MODULE_DESCRIPTION()s under net/802*
net: fill in MODULE_DESCRIPTION()s under net/core
net: fill in MODULE_DESCRIPTION()s in kuba@'s modules
xfrm: policy: fix layer 4 flowi decoding
xfrm Fix use after free in __xfrm6_udp_encap_rcv.
xfrm: policy: replace session decode with flow dissector
xfrm: move mark and oif flowi decode into common code
xfrm: pass struct net to xfrm_decode_session wrappers
xfrm: Support GRO for IPv6 ESP in UDP encapsulation
xfrm: Support GRO for IPv4 ESP in UDP encapsulation
xfrm: Use the XFRM_GRO to indicate a GRO call on input
xfrm: Annotate struct xfrm_sec_ctx with __counted_by
xfrm: Remove unused function declarations
-----BEGIN PGP SIGNATURE-----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=sk8+
-----END PGP SIGNATURE-----
Merge tag 'for-6.7/io_uring-sockopt-2023-10-30' of git://git.kernel.dk/linux
Pull io_uring {get,set}sockopt support from Jens Axboe:
"This adds support for using getsockopt and setsockopt via io_uring.
The main use cases for this is to enable use of direct descriptors,
rather than first instantiating a normal file descriptor, doing the
option tweaking needed, then turning it into a direct descriptor. With
this support, we can avoid needing a regular file descriptor
completely.
The net and bpf bits have been signed off on their side"
* tag 'for-6.7/io_uring-sockopt-2023-10-30' of git://git.kernel.dk/linux:
selftests/bpf/sockopt: Add io_uring support
io_uring/cmd: Introduce SOCKET_URING_OP_SETSOCKOPT
io_uring/cmd: Introduce SOCKET_URING_OP_GETSOCKOPT
io_uring/cmd: return -EOPNOTSUPP if net is disabled
selftests/net: Extract uring helpers to be reusable
tools headers: Grab copy of io_uring.h
io_uring/cmd: Pass compat mode in issue_flags
net/socket: Break down __sys_getsockopt
net/socket: Break down __sys_setsockopt
bpf: Add sockptr support for setsockopt
bpf: Add sockptr support for getsockopt
-----BEGIN PGP SIGNATURE-----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=slHB
-----END PGP SIGNATURE-----
Merge tag 'ipsec-next-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2023-10-28
1) Remove unused function declarations of xfrm4_extract_input and
xfrm6_extract_input. From Yue Haibing.
2) Annotate struct xfrm_sec_ctx with __counted_by.
From Kees Cook.
3) Support GRO decapsulation for ESP in UDP encapsulation.
From Antony Antony et all.
4) Replace the xfrm session decode with flow dissector.
From Florian Westphal.
5) Fix a use after free in __xfrm6_udp_encap_rcv.
6) Fix the layer 4 flowi decoding.
From Florian Westphal.
* tag 'ipsec-next-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: policy: fix layer 4 flowi decoding
xfrm Fix use after free in __xfrm6_udp_encap_rcv.
xfrm: policy: replace session decode with flow dissector
xfrm: move mark and oif flowi decode into common code
xfrm: pass struct net to xfrm_decode_session wrappers
xfrm: Support GRO for IPv6 ESP in UDP encapsulation
xfrm: Support GRO for IPv4 ESP in UDP encapsulation
xfrm: Use the XFRM_GRO to indicate a GRO call on input
xfrm: Annotate struct xfrm_sec_ctx with __counted_by
xfrm: Remove unused function declarations
====================
Link: https://lore.kernel.org/r/20231028084328.3119236-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add TCP_AO_REPAIR setsockopt(), getsockopt(). They let a user to repair
TCP-AO ISNs/SNEs. Also let the user hack around when (tp->repair) is on
and add ao_info on a socket in any supported state.
As SNEs now can be read/written at any moment, use
WRITE_ONCE()/READ_ONCE() to set/read them.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly how TCP_MD5SIG_FLAG_IFINDEX works for TCP-MD5,
TCP_AO_KEYF_IFINDEX is an AO-key flag that binds that MKT to a specified
by L3 ifinndex. Similarly, without this flag the key will work in
the default VRF l3index = 0 for connections.
To prevent AO-keys from overlapping, it's restricted to add key B for a
socket that has key A, which have the same sndid/rcvid and one of
the following is true:
- !(A.keyflags & TCP_AO_KEYF_IFINDEX) or !(B.keyflags & TCP_AO_KEYF_IFINDEX)
so that any key is non-bound to a VRF
- A.l3index == B.l3index
both want to work for the same VRF
Additionally, it's restricted to match TCP-MD5 keys for the same peer
the following way:
|--------------|--------------------|----------------|---------------|
| | MD5 key without | MD5 key | MD5 key |
| | l3index | l3index=0 | l3index=N |
|--------------|--------------------|----------------|---------------|
| TCP-AO key | | | |
| without | reject | reject | reject |
| l3index | | | |
|--------------|--------------------|----------------|---------------|
| TCP-AO key | | | |
| l3index=0 | reject | reject | allow |
|--------------|--------------------|----------------|---------------|
| TCP-AO key | | | |
| l3index=N | reject | allow | reject |
|--------------|--------------------|----------------|---------------|
This is done with the help of tcp_md5_do_lookup_any_l3index() to reject
adding AO key without TCP_AO_KEYF_IFINDEX if there's TCP-MD5 in any VRF.
This is important for case where sysctl_tcp_l3mdev_accept = 1
Similarly, for TCP-AO lookups tcp_ao_do_lookup() may be used with
l3index < 0, so that __tcp_ao_key_cmp() will match TCP-AO key in any VRF.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to TCP-MD5, add a static key to TCP-AO that is patched out
when there are no keys on a machine and dynamically enabled with the
first setsockopt(TCP_AO) adds a key on any socket. The static key is as
well dynamically disabled later when the socket is destructed.
The lifetime of enabled static key here is the same as ao_info: it is
enabled on allocation, passed over from full socket to twsk and
destructed when ao_info is scheduled for destruction.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce getsockopt(TCP_AO_GET_KEYS) that lets a user get TCP-AO keys
and their properties from a socket. The user can provide a filter
to match the specific key to be dumped or ::get_all = 1 may be
used to dump all keys in one syscall.
Add another getsockopt(TCP_AO_INFO) for providing per-socket/per-ao_info
stats: packet counters, Current_key/RNext_key and flags like
::ao_required and ::accept_icmps.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to IPsec, RFC5925 prescribes:
">> A TCP-AO implementation MUST default to ignore incoming ICMPv4
messages of Type 3 (destination unreachable), Codes 2-4 (protocol
unreachable, port unreachable, and fragmentation needed -- ’hard
errors’), and ICMPv6 Type 1 (destination unreachable), Code 1
(administratively prohibited) and Code 4 (port unreachable) intended
for connections in synchronized states (ESTABLISHED, FIN-WAIT-1, FIN-
WAIT-2, CLOSE-WAIT, CLOSING, LAST-ACK, TIME-WAIT) that match MKTs."
A selftest (later in patch series) verifies that this attack is not
possible in this TCP-AO implementation.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for logging connection-detailed messages for failed TCP
hash verification (both MD5 and AO).
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Sequence Number Extension (SNE) for TCP-AO.
This is needed to protect long-living TCP-AO connections from replaying
attacks after sequence number roll-over, see RFC5925 (6.2).
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce segment counters that are useful for troubleshooting/debugging
as well as for writing tests.
Now there are global snmp counters as well as per-socket and per-key.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there is a common function to verify signature on TCP segments:
tcp_inbound_hash(). It has checks for all possible cross-interactions
with MD5 signs as well as with unsigned segments.
The rules from RFC5925 are:
(1) Any TCP segment can have at max only one signature.
(2) TCP connections can't switch between using TCP-MD5 and TCP-AO.
(3) TCP-AO connections can't stop using AO, as well as unsigned
connections can't suddenly start using AO.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to RST segments, wire SYN-ACKs to TCP-AO.
tcp_rsk_used_ao() is handy here to check if the request socket used AO
and needs a signature on the outgoing segments.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when the new request socket is created from the listening socket,
it's recorded what MKT was used by the peer. tcp_rsk_used_ao() is
a new helper for checking if TCP-AO option was used to create the
request socket.
tcp_ao_copy_all_matching() will copy all keys that match the peer on the
request socket, as well as preparing them for the usage (creating
traffic keys).
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for sockets in time-wait state.
ao_info as well as all keys are inherited on transition to time-wait
socket. The lifetime of ao_info is now protected by ref counter, so
that tcp_ao_destroy_sock() will destruct it only when the last user is
gone.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up sending resets to TCP-AO hashing.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper that:
(1) shares the common code with TCP-MD5 header options parsing
(2) looks for hash signature only once for both TCP-MD5 and TCP-AO
(3) fails with -EEXIST if any TCP sign option is present twice, see
RFC5925 (2.2):
">> A single TCP segment MUST NOT have more than one TCP-AO in its
options sequence. When multiple TCP-AOs appear, TCP MUST discard
the segment."
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using precalculated traffic keys, sign TCP segments as prescribed by
RFC5925. Per RFC, TCP header options are included in sign calculation:
"The TCP header, by default including options, and where the TCP
checksum and TCP-AO MAC fields are set to zero, all in network-
byte order." (5.1.3)
tcp_ao_hash_header() has exclude_options parameter to optionally exclude
TCP header from hash calculation, as described in RFC5925 (9.1), this is
needed for interaction with middleboxes that may change "some TCP
options". This is wired up to AO key flags and setsockopt() later.
Similarly to TCP-MD5 hash TCP segment fragments.
From this moment a user can start sending TCP-AO signed segments with
one of crypto ahash algorithms from supported by Linux kernel. It can
have a user-specified MAC length, to either save TCP option header space
or provide higher protection using a longer signature.
The inbound segments are not yet verified, TCP-AO option is ignored and
they are accepted.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add traffic key calculation the way it's described in RFC5926.
Wire it up to tcp_finish_connect() and cache the new keys straight away
on already established TCP connections.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be as conservative as possible: if there is TCP-MD5 key for a given peer
regardless of L3 interface - don't allow setting TCP-AO key for the same
peer. According to RFC5925, TCP-AO is supposed to replace TCP-MD5 and
there can't be any switch between both on any connected tuple.
Later it can be relaxed, if there's a use, but in the beginning restrict
any intersection.
Note: it's still should be possible to set both TCP-MD5 and TCP-AO keys
on a listening socket for *different* peers.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 3 setsockopt()s:
1. TCP_AO_ADD_KEY to add a new Master Key Tuple (MKT) on a socket
2. TCP_AO_DEL_KEY to delete present MKT from a socket
3. TCP_AO_INFO to change flags, Current_key/RNext_key on a TCP-AO sk
Userspace has to introduce keys on every socket it wants to use TCP-AO
option on, similarly to TCP_MD5SIG/TCP_MD5SIG_EXT.
RFC5925 prohibits definition of MKTs that would match the same peer,
so do sanity checks on the data provided by userspace. Be as
conservative as possible, including refusal of defining MKT on
an established connection with no AO, removing the key in-use and etc.
(1) and (2) are to be used by userspace key manager to add/remove keys.
(3) main purpose is to set RNext_key, which (as prescribed by RFC5925)
is the KeyID that will be requested in TCP-AO header from the peer to
sign their segments with.
At this moment the life of ao_info ends in tcp_v4_destroy_sock().
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new kernel config option and common structures as well as
helpers to be used by TCP-AO code.
Co-developed-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Co-developed-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP-AO, similarly to TCP-MD5, needs to allocate tfms on a slow-path,
which is setsockopt() and use crypto ahash requests on fast paths,
which are RX/TX softirqs. Also, it needs a temporary/scratch buffer
for preparing the hash.
Rework tcp_md5sig_pool in order to support other hashing algorithms
than MD5. It will make it possible to share pre-allocated crypto_ahash
descriptors and scratch area between all TCP hash users.
Internally tcp_sigpool calls crypto_clone_ahash() API over pre-allocated
crypto ahash tfm. Kudos to Herbert, who provided this new crypto API.
I was a little concerned over GFP_ATOMIC allocations of ahash and
crypto_request in RX/TX (see tcp_sigpool_start()), so I benchmarked both
"backends" with different algorithms, using patched version of iperf3[2].
On my laptop with i7-7600U @ 2.80GHz:
clone-tfm per-CPU-requests
TCP-MD5 2.25 Gbits/sec 2.30 Gbits/sec
TCP-AO(hmac(sha1)) 2.53 Gbits/sec 2.54 Gbits/sec
TCP-AO(hmac(sha512)) 1.67 Gbits/sec 1.64 Gbits/sec
TCP-AO(hmac(sha384)) 1.77 Gbits/sec 1.80 Gbits/sec
TCP-AO(hmac(sha224)) 1.29 Gbits/sec 1.30 Gbits/sec
TCP-AO(hmac(sha3-512)) 481 Mbits/sec 480 Mbits/sec
TCP-AO(hmac(md5)) 2.07 Gbits/sec 2.12 Gbits/sec
TCP-AO(hmac(rmd160)) 1.01 Gbits/sec 995 Mbits/sec
TCP-AO(cmac(aes128)) [not supporetd yet] 2.11 Gbits/sec
So, it seems that my concerns don't have strong grounds and per-CPU
crypto_request allocation can be dropped/removed from tcp_sigpool once
ciphers get crypto_clone_ahash() support.
[1]: https://lore.kernel.org/all/ZDefxOq6Ax0JeTRH@gondor.apana.org.au/T/#u
[2]: https://github.com/0x7f454c46/iperf/tree/tcp-md5-ao
Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The third, and most likely the last, features pull request for v6.7.
Fixes all over and only few small new features.
Major changes:
iwlwifi
* more Multi-Link Operation (MLO) work
ath12k
* QCN9274: mesh support
ath11k
* firmware-2.bin container file format support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmU6KqgRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtyMwf7B/BqV0LCNzBxtrWl3WYtgQgULgWFmEJt
83/Vo8pXelZzzMMERwvZtPCwEUm/L/vOO/a/k0oSz/XQbt4PTIBGnWA7JwYZGY++
1Kc79oMyXxG4Q4RCnKG/qQMzCnyL54RHUfFQrNaa3Bkgp7vGobU+ixH4NaqHI3M9
OFmyhCklk9AO0VTtT6vQQBM6wM3UC1adneZMVlb8xD2Wi5rkrRk4PX5msgaYrStR
ketZE6IPnnX8DziqGZPlTz1SSuOSnwGTOramdeGLKIUUlZbPWHTSBZ8lh/xnvGUB
561mp3/iguFtq2NvduPBqItotBzLGvnJZbLDrBPxB/v99q+7/cziSA==
=Xf7b
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.7
The third, and most likely the last, features pull request for v6.7.
Fixes all over and only few small new features.
Major changes:
iwlwifi
- more Multi-Link Operation (MLO) work
ath12k
- QCN9274: mesh support
ath11k
- firmware-2.bin container file format support
* tag 'wireless-next-2023-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (155 commits)
wifi: ray_cs: Remove unnecessary (void*) conversions
Revert "wifi: ath11k: call ath11k_mac_fils_discovery() without condition"
wifi: ath12k: Introduce and use ath12k_sta_to_arsta()
wifi: ath12k: fix htt mlo-offset event locking
wifi: ath12k: fix dfs-radar and temperature event locking
wifi: ath11k: fix gtk offload status event locking
wifi: ath11k: fix htt pktlog locking
wifi: ath11k: fix dfs radar event locking
wifi: ath11k: fix temperature event locking
wifi: ath12k: rename the sc naming convention to ab
wifi: ath12k: rename the wmi_sc naming convention to wmi_ab
wifi: ath11k: add firmware-2.bin support
wifi: ath11k: qmi: refactor ath11k_qmi_m3_load()
wifi: rtw89: cleanup firmware elements parsing
wifi: rt2x00: rework MT7620 PA/LNA RF calibration
wifi: rt2x00: rework MT7620 channel config function
wifi: rt2x00: improve MT7620 register initialization
MAINTAINERS: wifi: rt2x00: drop Helmut Schaa
wifi: wlcore: main: replace deprecated strncpy with strscpy
wifi: wlcore: boot: replace deprecated strncpy with strscpy
...
====================
Link: https://lore.kernel.org/r/20231026090411.B2426C433CB@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZTp12QAKCRDbK58LschI
g8BrAQDifqp5liEEdXV8jdReBwJtqInjrL5tzy5LcyHUMQbTaAEA6Ph3Ct3B+3oA
mFnIW/y6UJiJrby0Xz4+vV5BXI/5WQg=
=pLCV
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-10-26
We've added 51 non-merge commits during the last 10 day(s) which contain
a total of 75 files changed, 5037 insertions(+), 200 deletions(-).
The main changes are:
1) Add open-coded task, css_task and css iterator support.
One of the use cases is customizable OOM victim selection via BPF,
from Chuyi Zhou.
2) Fix BPF verifier's iterator convergence logic to use exact states
comparison for convergence checks, from Eduard Zingerman,
Andrii Nakryiko and Alexei Starovoitov.
3) Add BPF programmable net device where bpf_mprog defines the logic
of its xmit routine. It can operate in L3 and L2 mode,
from Daniel Borkmann and Nikolay Aleksandrov.
4) Batch of fixes for BPF per-CPU kptr and re-enable unit_size checking
for global per-CPU allocator, from Hou Tao.
5) Fix libbpf which eagerly assumed that SHT_GNU_verdef ELF section
was going to be present whenever a binary has SHT_GNU_versym section,
from Andrii Nakryiko.
6) Fix BPF ringbuf correctness to fold smp_mb__before_atomic() into
atomic_set_release(), from Paul E. McKenney.
7) Add a warning if NAPI callback missed xdp_do_flush() under
CONFIG_DEBUG_NET which helps checking if drivers were missing
the former, from Sebastian Andrzej Siewior.
8) Fix missed RCU read-lock in bpf_task_under_cgroup() which was throwing
a warning under sleepable programs, from Yafang Shao.
9) Avoid unnecessary -EBUSY from htab_lock_bucket by disabling IRQ before
checking map_locked, from Song Liu.
10) Make BPF CI linked_list failure test more robust,
from Kumar Kartikeya Dwivedi.
11) Enable samples/bpf to be built as PIE in Fedora, from Viktor Malik.
12) Fix xsk starving when multiple xsk sockets were associated with
a single xsk_buff_pool, from Albert Huang.
13) Clarify the signed modulo implementation for the BPF ISA standardization
document that it uses truncated division, from Dave Thaler.
14) Improve BPF verifier's JEQ/JNE branch taken logic to also consider
signed bounds knowledge, from Andrii Nakryiko.
15) Add an option to XDP selftests to use multi-buffer AF_XDP
xdp_hw_metadata and mark used XDP programs as capable to use frags,
from Larysa Zaremba.
16) Fix bpftool's BTF dumper wrt printing a pointer value and another
one to fix struct_ops dump in an array, from Manu Bretelle.
* tag 'for-netdev' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (51 commits)
netkit: Remove explicit active/peer ptr initialization
selftests/bpf: Fix selftests broken by mitigations=off
samples/bpf: Allow building with custom bpftool
samples/bpf: Fix passing LDFLAGS to libbpf
samples/bpf: Allow building with custom CFLAGS/LDFLAGS
bpf: Add more WARN_ON_ONCE checks for mismatched alloc and free
selftests/bpf: Add selftests for netkit
selftests/bpf: Add netlink helper library
bpftool: Extend net dump with netkit progs
bpftool: Implement link show support for netkit
libbpf: Add link-based API for netkit
tools: Sync if_link uapi header
netkit, bpf: Add bpf programmable net device
bpf: Improve JEQ/JNE branch taken logic
bpf: Fold smp_mb__before_atomic() into atomic_set_release()
bpf: Fix unnecessary -EBUSY from htab_lock_bucket
xsk: Avoid starving the xsk further down the list
bpf: print full verifier states on infinite loop detection
selftests/bpf: test if state loops are detected in a tricky case
bpf: correct loop detection for iterators convergence
...
====================
Link: https://lore.kernel.org/r/20231026150509.2824-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct nla_policy is usually constant itself, but unless
we make the ranges inside constant we won't be able to
make range structs const. The ranges are not modified
by the core.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20231025162204.132528-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ZG+P
-----END PGP SIGNATURE-----
Merge tag 'nf-next-23-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next. Mostly
nf_tables updates with two patches for connlabel and br_netfilter.
1) Rename function name to perform on-demand GC for rbtree elements,
and replace async GC in rbtree by sync GC. Patches from Florian Westphal.
2) Use commit_mutex for NFT_MSG_GETRULE_RESET to ensure that two
concurrent threads invoking this command do not underrun stateful
objects. Patches from Phil Sutter.
3) Use single hook to deal with IP and ARP packets in br_netfilter.
Patch from Florian Westphal.
4) Use atomic_t in netns->connlabel use counter instead of using a
spinlock, also patch from Florian.
5) Cleanups for stateful objects infrastructure in nf_tables.
Patches from Phil Sutter.
6) Flush path uses opaque set element offered by the iterator, instead of
calling pipapo_deactivate() which looks up for it again.
7) Set backend .flush interface always succeeds, make it return void
instead.
8) Add struct nft_elem_priv placeholder structure and use it by replacing
void * to pass opaque set element representation from backend to frontend
which defeats compiler type checks.
9) Shrink memory consumption of set element transactions, by reducing
struct nft_trans_elem object size and reducing stack memory usage.
10) Use struct nft_elem_priv also for set backend .insert operation too.
11) Carry reset flag in nft_set_dump_ctx structure, instead of passing it
as a function argument, from Phil Sutter.
netfilter pull request 23-10-25
* tag 'nf-next-23-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_tables: Carry reset boolean in nft_set_dump_ctx
netfilter: nf_tables: set->ops->insert returns opaque set element in case of EEXIST
netfilter: nf_tables: shrink memory consumption of set elements
netfilter: nf_tables: expose opaque set element as struct nft_elem_priv
netfilter: nf_tables: set backend .flush always succeeds
netfilter: nft_set_pipapo: no need to call pipapo_deactivate() from flush
netfilter: nf_tables: Carry reset boolean in nft_obj_dump_ctx
netfilter: nf_tables: nft_obj_filter fits into cb->ctx
netfilter: nf_tables: Carry s_idx in nft_obj_dump_ctx
netfilter: nf_tables: A better name for nft_obj_filter
netfilter: nf_tables: Unconditionally allocate nft_obj_filter
netfilter: nf_tables: Drop pointless memset in nf_tables_dump_obj
netfilter: conntrack: switch connlabels to atomic_t
br_netfilter: use single forward hook for ip and arp
netfilter: nf_tables: Add locking for NFT_MSG_GETRULE_RESET requests
netfilter: nf_tables: Introduce nf_tables_getrule_single()
netfilter: nf_tables: Open-code audit log call in nf_tables_getrule()
netfilter: nft_set_rbtree: prefer sync gc to async worker
netfilter: nft_set_rbtree: rename gc deactivate+erase function
====================
Link: https://lore.kernel.org/r/20231025212555.132775-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
RTAX_FEATURE_ALLFRAG was added before the first git commit:
https://www.mail-archive.com/bk-commits-head@vger.kernel.org/msg03399.html
The feature would send packets to the fragmentation path if a box
receives a PMTU value with less than 1280 byte. However, since commit
9d289715eb ("ipv6: stop sending PTB packets for MTU < 1280"), such
message would be simply discarded. The feature flag is neither supported
in iproute2 utility. In theory one can still manipulate it with direct
netlink message, but it is not ideal because it was based on obsoleted
guidance of RFC-2460 (replaced by RFC-8200).
The feature would always test false at the moment, so remove related
code or mark them as unused.
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/d78e44dcd9968a252143ffe78460446476a472a1.1698156966.git.yan@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So that other users could access it. Notably MPTCP will use
it in the next patch.
No functional change intended.
Acked-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231023-send-net-next-20231023-2-v1-4-9dc60939d371@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since 41f2c7c342 ("net/sched: act_ct: Fix promotion of offloaded
unreplied tuple"), flowtable GC pushes back flows with IPS_SEEN_REPLY
back to classic path in every run, ie. every second. This is because of
a new check for NF_FLOW_HW_ESTABLISHED which is specific of sched/act_ct.
In Netfilter's flowtable case, NF_FLOW_HW_ESTABLISHED never gets set on
and IPS_SEEN_REPLY is unreliable since users decide when to offload the
flow before, such bit might be set on at a later stage.
Fix it by adding a custom .gc handler that sched/act_ct can use to
deal with its NF_FLOW_HW_ESTABLISHED bit.
Fixes: 41f2c7c342 ("net/sched: act_ct: Fix promotion of offloaded unreplied tuple")
Reported-by: Vladimir Smelhaus <vl.sm@email.cz>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net->ct.labels_used was meant to convey 'number of ip/nftables rules
that need the label extension allocated'.
act_ct enables this for each net namespace, which voids all attempts
to avoid ct->ext allocation when possible.
Move this increment to the control plane to request label extension
space allocation only when its needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a new, minimal BPF-programmable device called "netkit"
(former PoC code-name "meta") we recently presented at LSF/MM/BPF. The
core idea is that BPF programs are executed within the drivers xmit routine
and therefore e.g. in case of containers/Pods moving BPF processing closer
to the source.
One of the goals was that in case of Pod egress traffic, this allows to
move BPF programs from hostns tcx ingress into the device itself, providing
earlier drop or forward mechanisms, for example, if the BPF program
determines that the skb must be sent out of the node, then a redirect to
the physical device can take place directly without going through per-CPU
backlog queue. This helps to shift processing for such traffic from softirq
to process context, leading to better scheduling decisions/performance (see
measurements in the slides).
In this initial version, the netkit device ships as a pair, but we plan to
extend this further so it can also operate in single device mode. The pair
comes with a primary and a peer device. Only the primary device, typically
residing in hostns, can manage BPF programs for itself and its peer. The
peer device is designated for containers/Pods and cannot attach/detach
BPF programs. Upon the device creation, the user can set the default policy
to 'pass' or 'drop' for the case when no BPF program is attached.
Additionally, the device can be operated in L3 (default) or L2 mode. The
management of BPF programs is done via bpf_mprog, so that multi-attach is
supported right from the beginning with similar API and dependency controls
as tcx. For details on the latter see commit 053c8e1f23 ("bpf: Add generic
attach/detach/query API for multi-progs"). tc BPF compatibility is provided,
so that existing programs can be easily migrated.
Going forward, we plan to use netkit devices in Cilium as the main device
type for connecting Pods. They will be operated in L3 mode in order to
simplify a Pod's neighbor management and the peer will operate in default
drop mode, so that no traffic is leaving between the time when a Pod is
brought up by the CNI plugin and programs attached by the agent.
Additionally, the programs we attach via tcx on the physical devices are
using bpf_redirect_peer() for inbound traffic into netkit device, hence the
latter is also supporting the ndo_get_peer_dev callback. Similarly, we use
bpf_redirect_neigh() for the way out, pushing from netkit peer to phys device
directly. Also, BIG TCP is supported on netkit device. For the follow-up
work in single device mode, we plan to convert Cilium's cilium_host/_net
devices into a single one.
An extensive test suite for checking device operations and the BPF program
and link management API comes as BPF selftests in this series.
Co-developed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://github.com/borkmann/iproute2/tree/pr/netkit
Link: http://vger.kernel.org/bpfconf2023_material/tcx_meta_netdev_borkmann.pdf (24ff.)
Link: https://lore.kernel.org/r/20231024214904.29825-2-daniel@iogearbox.net
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Use more inclusive terms throughout the DSA subsystem by moving away
from "master" which is replaced by "conduit" and "slave" which is
replaced by "user". No functional changes.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return struct nft_elem_priv instead of struct nft_set_ext for
consistency with ("netfilter: nf_tables: expose opaque set element as
struct nft_elem_priv") and to prepare the introduction of element
timeout updates from control path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of copying struct nft_set_elem into struct nft_trans_elem, store
the pointer to the opaque set element object in the transaction. Adapt
set backend API (and set backend implementations) to take the pointer to
opaque set element representation whenever required.
This patch deconstifies .remove() and .activate() set backend API since
these modify the set element opaque object. And it also constify
nft_set_elem_ext() this provides access to the nft_set_ext struct
without updating the object.
According to pahole on x86_64, this patch shrinks struct nft_trans_elem
size from 216 to 24 bytes.
This patch also reduces stack memory consumption by removing the
template struct nft_set_elem object, using the opaque set element object
instead such as from the set iterator API, catchall elements and the get
element command.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add placeholder structure and place it at the beginning of each struct
nft_*_elem for each existing set backend, instead of exposing elements
as void type to the frontend which defeats compiler type checks. Use
this pointer to this new type to replace void *.
This patch updates the following set backend API to use this new struct
nft_elem_priv placeholder structure:
- update
- deactivate
- flush
- get
as well as the following helper functions:
- nft_set_elem_ext()
- nft_set_elem_init()
- nft_set_elem_destroy()
- nf_tables_set_elem_destroy()
This patch adds nft_elem_priv_cast() to cast struct nft_elem_priv to
native element representation from the corresponding set backend.
BUILD_BUG_ON() makes sure this .priv placeholder is always at the top
of the opaque set element representation.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
.flush is always successful since this results from iterating over the
set elements to toggle mark the element as inactive in the next
generation.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The spinlock is back from the day when connabels did not have
a fixed size and reallocation had to be supported.
Remove it. This change also allows to call the helpers from
softirq or timers without deadlocks.
Also add WARN()s to catch refcounting imbalances.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the previous implementation, when multiple xsk sockets were
associated with a single xsk_buff_pool, a situation could arise
where the xsk_tx_list maintained data at the front for one xsk
socket while starving the xsk sockets at the back of the list.
This could result in issues such as the inability to transmit packets,
increased latency, and jitter. To address this problem, we introduce
a new variable called tx_budget_spent, which limits each xsk to transmit
a maximum of MAX_PER_SOCKET_BUDGET tx descriptors. This allocation ensures
equitable opportunities for subsequent xsk sockets to send tx descriptors.
The value of MAX_PER_SOCKET_BUDGET is set to 32.
Signed-off-by: Albert Huang <huangjie.albert@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20231023125732.82261-1-huangjie.albert@bytedance.com
As more drivers begin to use the fragment API, update the
document about how to decide which API to use for the
driver author.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
CC: Lorenzo Bianconi <lorenzo@kernel.org>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Liang Chen <liangchen.linux@gmail.com>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
CC: Dima Tisnek <dimaqq@gmail.com>
Link: https://lore.kernel.org/r/20231020095952.11055-5-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently page pool supports the below use cases:
use case 1: allocate page without page splitting using
page_pool_alloc_pages() API if the driver knows
that the memory it need is always bigger than
half of the page allocated from page pool.
use case 2: allocate page frag with page splitting using
page_pool_alloc_frag() API if the driver knows
that the memory it need is always smaller than
or equal to the half of the page allocated from
page pool.
There is emerging use case [1] & [2] that is a mix of the
above two case: the driver doesn't know the size of memory it
need beforehand, so the driver may use something like below to
allocate memory with least memory utilization and performance
penalty:
if (size << 1 > max_size)
page = page_pool_alloc_pages();
else
page = page_pool_alloc_frag();
To avoid the driver doing something like above, add the
page_pool_alloc() API to support the above use case, and update
the true size of memory that is acctually allocated by updating
'*size' back to the driver in order to avoid exacerbating
truesize underestimate problem.
Rename page_pool_free() which is used in the destroy process to
__page_pool_destroy() to avoid confusion with the newly added
API.
1. https://lore.kernel.org/all/d3ae6bd3537fbce379382ac6a42f67e22f27ece2.1683896626.git.lorenzo@kernel.org/
2. https://lore.kernel.org/all/20230526054621.18371-3-liangchen.linux@gmail.com/
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
CC: Lorenzo Bianconi <lorenzo@kernel.org>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Liang Chen <liangchen.linux@gmail.com>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20231020095952.11055-4-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PP_FLAG_PAGE_FRAG is not really needed after pp_frag_count
handling is unified and page_pool_alloc_frag() is supported
in 32-bit arch with 64-bit DMA, so remove it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
CC: Lorenzo Bianconi <lorenzo@kernel.org>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Liang Chen <liangchen.linux@gmail.com>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20231020095952.11055-3-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently when page_pool_create() is called with
PP_FLAG_PAGE_FRAG flag, page_pool_alloc_pages() is only
allowed to be called under the below constraints:
1. page_pool_fragment_page() need to be called to setup
page->pp_frag_count immediately.
2. page_pool_defrag_page() often need to be called to drain
the page->pp_frag_count when there is no more user will
be holding on to that page.
Those constraints exist in order to support a page to be
split into multi fragments.
And those constraints have some overhead because of the
cache line dirtying/bouncing and atomic update.
Those constraints are unavoidable for case when we need a
page to be split into more than one fragment, but there is
also case that we want to avoid the above constraints and
their overhead when a page can't be split as it can only
hold a fragment as requested by user, depending on different
use cases:
use case 1: allocate page without page splitting.
use case 2: allocate page with page splitting.
use case 3: allocate page with or without page splitting
depending on the fragment size.
Currently page pool only provide page_pool_alloc_pages() and
page_pool_alloc_frag() API to enable the 1 & 2 separately,
so we can not use a combination of 1 & 2 to enable 3, it is
not possible yet because of the per page_pool flag
PP_FLAG_PAGE_FRAG.
So in order to allow allocating unsplit page without the
overhead of split page while still allow allocating split
page we need to remove the per page_pool flag in
page_pool_is_last_frag(), as best as I can think of, it seems
there are two methods as below:
1. Add per page flag/bit to indicate a page is split or
not, which means we might need to update that flag/bit
everytime the page is recycled, dirtying the cache line
of 'struct page' for use case 1.
2. Unify the page->pp_frag_count handling for both split and
unsplit page by assuming all pages in the page pool is split
into a big fragment initially.
As page pool already supports use case 1 without dirtying the
cache line of 'struct page' whenever a page is recyclable, we
need to support the above use case 3 with minimal overhead,
especially not adding any noticeable overhead for use case 1,
and we are already doing an optimization by not updating
pp_frag_count in page_pool_defrag_page() for the last fragment
user, this patch chooses to unify the pp_frag_count handling
to support the above use case 3.
There is no noticeable performance degradation and some
justification for unifying the frag_count handling with this
patch applied using a micro-benchmark testing in [1].
1. https://lore.kernel.org/all/bf2591f8-7b3c-4480-bb2c-31dc9da1d6ac@huawei.com/
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
CC: Lorenzo Bianconi <lorenzo@kernel.org>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Liang Chen <liangchen.linux@gmail.com>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20231020095952.11055-2-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The handle of new hci_conn is always HCI_CONN_HANDLE_MAX + 1 if
the handle of the first hci_conn entry in hci_dev->conn_hash->list
is not HCI_CONN_HANDLE_MAX + 1. Use ida to manage the allocation of
hci_conn->handle to make it be unique.
Fixes: 9f78191cc9 ("Bluetooth: hci_conn: Always allocate unique handles")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
