If we issue the link startup to the device while its UniPro state is
LinkDown (and device state is sleep/power-down) then link startup
will not move the device state to Active. Device will only move to
active state if the link starup is issued when its UniPro state is
LinkUp. So in this case, we would have to issue the link startup 2
times to make sure that device moves to active state.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices require host PA_TACTIVATE to be higher than
device PA_TACTIVATE otherwise it may get stuck during hibern8 sequence.
This change allows this by using quirk.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is found thats UFS device may take longer than 30ms to respond to
query requests and in this case we might run into following scenario:
1. UFS host SW sends a query request to UFS device to read an attribute
value. SW uses tag #31 for this purpose.
2. UFS host SW waits for 30ms to get the query response (and doorbell
to be cleared by UFS host HW).
3. UFS device doesn't respond back within 30ms hence UFS host SW times
out waiting for the query response.
4. UFS host SW clears the tag#31 from UTRLCLR register.
5. UFS host SW waits until UFS host HW to clear tag#31 from the doorbell
register.
6. UFS host SW retries the same query request on same tag#31 (sends a query
request to device to read an attribute value).
7. UFS host HW gets the query response from the device but this was
intended as a query response for the 1st query request sent (step-1).
8. Now UFS device sends another query response to host (for query request
sent @step-6).
Now there are 2 issues that could happen with above scenario:
1. UFS device should have actually responded back with only one query
response but it is found that device may respond back with 2 query
responses.
2. If UFS device responds back with 2 resposes on same tag, host HW/SW
behaviour isn't predictable.
To avoid running into above scenario, we would basically allow device
to take longer (upto 1.5 seconds) for query response.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reading variable size descriptors (like string descriptor), some UFS
devices may report the "LENGTH" (field in "Transaction Specific fields" of
Query Response UPIU) same as what was requested in Query Request UPIU
instead of reporting the actual size of the variable size descriptor.
Although it's safe to ignore the "LENGTH" field for variable size
descriptors as we can always derive the length of the descriptor from
the descriptor header fields. Hence this change impose the length match
check only for fixed size descriptors (for which we always request the
correct size as part of Query Request UPIU).
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to JESD220B - UFS v2.0, the maximum size of device descriptor
has changed from 0x1F to 0x40. This patch updates the maximum size of
this descriptor.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sending query to the device, the index of the failure
is additional useful information that should be printed out as it
might specify the logical unit (LU) where the error occurred.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some of the queries might fail during init. To avoid
system failure, we add retry mechanism to issue queries
several times.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controllers may think granularities of PRDT length and
offset as bytes, not double words.
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufs_qcom_init() sets the hba priv data before attempting to acquire the
phy handle, so make sure to clear this in the case of an error. Failing
to do this will make ufs_qcom_setup_clocks() operate on the uninitalized
host object.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new ufshcd_state, indicats that an err handler may get to run
immediately. Use UFSHCD_STATE_ERROR here looks not literaly correct.
Signed-off-by: Zang Leigang <zangleigang@hisilicon.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controller may need to configure some things around
hibern8 enter/exit
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controller may need to configure some things before any
task management request is issued
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controller may need to configure some things before any
transfer request is issued.
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch uses the resource-managed to add the devfreq device. This
function will make it easy to handle the devfreq device.
- struct devfreq *devm_devfreq_add_device(struct device *dev,
struct devfreq_dev_profile *profile,
const char *governor_name,
void *data);
Cc: Vinayak Holikatti <vinholikatti@gmail.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Host is allocated by managed kmalloc (devm_kmalloc). The
memory allocated with this function is automatically
freed on driver detach.
So, no need to make an exclusive free call over it.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do a phy_exit() over the ufs phy in the ufs qcom exit path
to de-initialize the phy.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add phy clock enable code to phy_power_on/off callbacks, and
remove explicit calls to enable these phy clocks from the
ufs-qcom hcd driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we are resuming the UFS device rails in HPM mode, we are first
powering on the VCC rail while VCCQ and VCCQ2 rails still being in LPM
mode. Some UFS devices may take VCC on event as hint that host wants UFS
device to be resumed and may start drawing more power from the
VCCQ/VCCQ2 rails (while they are still in LPM mode) causing voltage drop
on these rails. This change fixes this issue by bringing VCCQ & VCCQ2
rails out of LPM before powering on VCC rail.
Reviewed-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently clock scaling is suspended only after the host and device are
put in low power mode but we should avoid clock scaling running after
UFS link is put in low power mode (hibern8). This change suspends clock
scaling before putting host/device in low power mode.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If ufshcd pltfrm/pci driver's probe fails for some reason then ensure
that scsi host is released to avoid memory leak but managed memory
allocations (via devm_* calls) need not to be freed explicitly on probe
failure as memory allocated with these functions is automatically freed
on driver detach.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS devfreq clock scaling work may require clocks to be ON if it need to
execute some UFS commands hence it may request for clock hold before
issuing the command. But if UFS clock gating work is already running in
parallel, ungate work would end up waiting for the clock gating work to
finish and as clock gating work would also wait for the clock scaling
work to finish, we would enter in deadlock state. Here is the call trace
during this deadlock state:
Workqueue: devfreq_wq devfreq_monitor
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
ufshcd_hold
ufshcd_send_uic_cmd
ufshcd_dme_get_attr
ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div
ufs_qcom_clk_scale_notify
ufshcd_scale_clks
ufshcd_devfreq_target
update_devfreq
devfreq_monitor
process_one_work
worker_thread
kthread
ret_from_fork
Workqueue: events ufshcd_gate_work
__switch_to
__schedule
schedule
schedule_preempt_disabled
__mutex_lock_slowpath
mutex_lock
devfreq_monitor_suspend
devfreq_simple_ondemand_handler
devfreq_suspend_device
ufshcd_gate_work
process_one_work
worker_thread
kthread
ret_from_fork
Workqueue: events ufshcd_ungate_work
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
__cancel_work_timer
cancel_delayed_work_sync
ufshcd_ungate_work
process_one_work
worker_thread
kthread
ret_from_fork
This change fixes this deadlock by doing this in devfreq work (devfreq_wq):
Try cancelling clock gating work. If we are able to cancel gating work
or it wasn't scheduled, hold the clock reference count until scaling is
in progress. If gate work is already running in parallel, let's skip
the frequecy scaling at this time and it will be retried once next scaling
window expires.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a case where gate work is called as part of cancel work from ungate
path the clk state would be marked as REQ_CLKS_ON. There is no point
gating the clocks and then end up turning them ON immediately in ungate
work, save time by skipping the gate work and change the clk state to
CLKS_ON as they are not turned off yet.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ungate work turns on the clock before it exits hibern8, if the link
was put in hibern8 during clock gating work. There occurs a race
condition when clock scaling work calls ufshcd_hold() to make sure low
power states cannot be entered, but that returns by checking only
whether the clocks are on. This causes the clock scaling work to issue
UIC commands when the link is in hibern8 causing failures. Make sure we
exit hibern8 state before returning from ufshcd_hold().
Callstacks for race condition:
ufshcd_scale_gear
ufshcd_devfreq_scale
ufshcd_devfreq_target
update_devfreq
devfreq_monitor
process_one_work
worker_thread
kthread
ret_from_fork
ufshcd_uic_hibern8_exit
ufshcd_ungate_work
process_one_work
worker_thread
kthread
ret_from_fork
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case the power configuration fails, skip further processing of the
probing function and return immediately. This has 2 reasons:
1. Don't allow the UFS to continue running in PWM
2. Avoid multiple calls to pm_runtime_put_sync() when not in error
handling or power management contexts
Signed-off-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During runtime resume operation, clock scaling may get indirectly
resumed via call to ufshcd_set_dev_pwr_mode(): Start/Stop Unit command
times out and SCSI error handling ultimately calls the host reset
handler to recover, during which clock scaling is resumed. Error case
exit path of runtime resume will disable clocks. As clock scaling was
already resumed, it will get scheduled later on and try to access UFS
registers while clocks are disabled, resulting in unclocked register
access.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to UFS device specification, sense data can be only 18 bytes
long, this change makes the changes accordingly.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a write memory barrier to make sure descriptors prepared are
actually written to memory before ringing the doorbell. We have also
added the write memory barrier after ringing the doorbell register so
that controller sees the new request immediately.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In this change there are a few fixes of possible NULL pointer access and
possible access to index that exceeds array boundaries.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Vendor specific setup_clocks callback may require the clocks managed by
ufshcd driver to be ON. So if the vendor specific setup_clocks callback
is called while the required clocks are turned off, it could result into
unclocked register access.
To prevent possible unclock register access, this change adds one more
argument to setup_clocks callback to let it know whether it is called
pre/post the clock changes by core driver.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if we have PCI and UFSHCD configured in the kernel, both
SCSI_UFS_DWC_TC_PCI and SCSI_UFSHCD_PCI show up, which is not correct.
This patch changes the UFS Kconfig to assure hierarchy between the 2
options.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some devices have problems handling a Query UPIU with Data Segment
set. Only set it for WRITE DESCRIPTOR commands.
[mkp: updated patch description]
Signed-off-by: Zang Leigang <zangleigang@hisilicon.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch enable no vccq quirk for SKHynix devices. SKHynix ufs device
don't need vccq vrail for device operation.
Signed-off-by: Kyuho Choi <kyuho.choi@sk.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When any UFS host controller receives a TM(Task Management) response
from a UFS device, UFS driver has been recognize like receiving a
message of "Task Management Function Complete"(00h) in all cases, so
far. That means there is no pending task for a tag of the TM request
sent before in the UFS device. That's because the byte offset 6 in TM
response which has been used to get a TM service response so far
represents just whether or not a TM transmission passes.
Regarding UFS spec, the correct byte offset to get TM service response
is 15, not 6.
I tested that UFS driver responds properly for the TM response from a
UFS device with an reference board with exynos8890, as follow: No
pending task -> Task Management Function Complete (00h) Pending task ->
Task Management Function Succeeded (08h)
[mkp: applied by hand]
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: HeonGwang Chu <hg.chu@samsung.com>
Tested-by: : Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I modified a string as described in UFS spec as follow: umpcrs -> upmcrs.
[mkp: applied by hand]
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 2 warnings when build kernel with W=1:
drivers/scsi/ufs/tc-dwc-g210.c:261:5: warning: no previous prototype for 'tc_dwc_g210_config_40_bit' [-Wmissing-prototypes]
drivers/scsi/ufs/tc-dwc-g210.c:293:5: warning: no previous prototype for 'tc_dwc_g210_config_20_bit' [-Wmissing-prototypes]
In fact, these functions are declared in ufs/tc-dwc-g210.h, so this
patch add missing header dependencies
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When buff_ascii kmalloc failed, there is no need to call kfree, it
should return -ENOMEM directly, this patch fixes it.
Signed-off-by: Tiezhu Yang <kernelpatch@126.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code was checking on PA_CONNECTEDRXLANES and PA_CONNECTEDTXLANES
attributes to program the Lane#1 attributes. The correct attributes are
PA_AVAILRXDATALANES and PA_AVAILTXDATALANES respectively.
Signed-off-by: Manjunath M B <manjumb@synopsys.com>
Tested-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds license info to the tc-dwc-g210 and ufshcd-dwc files in
order for them to have access to some ufshcd symbols when all are built
as modules.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a glue pci driver for the Synopsys G210 Test Chip.
[mkp: Fixed Kconfig depends and module name]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a glue platform driver for the Synopsys G210 Test Chip.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for Synopsys G210 Test Chip.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch has the goal to add support for DesignWare UFS Controller
specific operations.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add link status to ufshci.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add unipro attributes.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add UFS 2.0 support to the UFS core driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed typo in ufshcd-pltfrm.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change to ufshcd introduced a call to utf16s_to_utf8s, a
function that is provided by the NLS module, so we get a link error when
that is not present:
drivers/scsi/built-in.o: In function `ufshcd_read_string_desc':
:(.text+0x124d0): undefined reference to `utf16s_to_utf8s'
This adds a Kconfig 'select' statement to avoid the build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b573d484e4 ("scsi: ufs: add support to read device and string descriptors")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change adds printouts of testbus and debug registers.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
