A ucode patch is needed for Goldmont Plus while counter freezing feature
is enabled. Otherwise, there will be some issues, e.g. PMI flood with
some events.
Add a quirk to check microcode version. If the system starts with the
wrong ucode, leave the counter-freezing feature permanently disabled.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Link: http://lkml.kernel.org/r/1533712328-2834-3-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implements counter freezing for Arch Perfmon v4 (Skylake and
newer). This allows to speed up the PMI handler by avoiding
unnecessary MSR writes and make it more accurate.
The Arch Perfmon v4 PMI handler is substantially different than
the older PMI handler.
Differences to the old handler:
- It relies on counter freezing, which eliminates several MSR
writes from the PMI handler and lowers the overhead significantly.
It makes the PMI handler more accurate, as all counters get
frozen atomically as soon as any counter overflows. So there is
much less counting of the PMI handler itself.
With the freezing we don't need to disable or enable counters or
PEBS. Only BTS which does not support auto-freezing still needs to
be explicitly managed.
- The PMU acking is done at the end, not the beginning.
This makes it possible to avoid manual enabling/disabling
of the PMU, instead we just rely on the freezing/acking.
- The APIC is acked before reenabling the PMU, which avoids
problems with LBRs occasionally not getting unfreezed on Skylake.
- Looping is only needed to workaround a corner case which several PMIs
are very close to each other. For common cases, the counters are freezed
during PMI handler. It doesn't need to do re-check.
This patch:
- Adds code to enable v4 counter freezing
- Fork <=v3 and >=v4 PMI handlers into separate functions.
- Add kernel parameter to disable counter freezing. It took some time to
debug counter freezing, so in case there are new problems we added an
option to turn it off. Would not expect this to be used until there
are new bugs.
- Only for big core. The patch for small core will be posted later
separately.
Performance:
When profiling a kernel build on Kabylake with different perf options,
measuring the length of all NMI handlers using the nmi handler
trace point:
V3 is without counter freezing.
V4 is with counter freezing.
The value is the average cost of the PMI handler.
(lower is better)
perf options ` V3(ns) V4(ns) delta
-c 100000 1088 894 -18%
-g -c 100000 1862 1646 -12%
--call-graph lbr -c 100000 3649 3367 -8%
--c.g. dwarf -c 100000 2248 1982 -12%
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Link: http://lkml.kernel.org/r/1533712328-2834-2-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Arch Perfmon v4 PMI handler is substantially different than
the older PMI handler. Instead of adding more and more ifs cleanly
fork the new handler into a new function, with the main common
code factored out into a common function.
Fix complaint from checkpatch.pl by removing "false" from "static bool
warned".
No functional change.
Based-on-code-from: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Link: http://lkml.kernel.org/r/1533712328-2834-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In Family 17h, some L3 Cache Performance events require the ThreadMask
and SliceMask to be set. For other events, these fields do not affect
the count either way.
Set ThreadMask and SliceMask to 0xFF and 0xF respectively.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H . Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The counters on M3UPI Link 0 and Link 3 don't count properly, and writing
0 to these counters may causes system crash on some machines.
The PCI BDF addresses of the M3UPI in the current code are incorrect.
The correct addresses should be:
D18:F1 0x204D
D18:F2 0x204E
D18:F5 0x204D
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: cd34cd97b7 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Link: http://lkml.kernel.org/r/1537538826-55489-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas writes:
"A single fix for the AMD memory encryption boot code so it does not
read random garbage instead of the cached encryption bit when a kexec
kernel is allocated above the 32bit address limit."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix kexec booting failure in the SEV bit detection code
The success of a cache pseudo-locked region is measured using
performance monitoring events that are programmed directly at the time
the user requests a measurement.
Modifying the performance event registers directly is not appropriate
since it circumvents the in-kernel perf infrastructure that exists to
manage these resources and provide resource arbitration to the
performance monitoring hardware.
The cache pseudo-locking measurements are modified to use the in-kernel
perf infrastructure. Performance events are created and validated with
the appropriate perf API. The performance counters are still read as
directly as possible to avoid the additional cache hits. This is
done safely by first ensuring with the perf API that the counters have
been programmed correctly and only accessing the counters in an
interrupt disabled section where they are not able to be moved.
As part of the transition to the in-kernel perf infrastructure the L2
and L3 measurements are split into two separate measurements that can
be triggered independently. This separation prevents additional cache
misses incurred during the extra testing code used to decide if a
L2 and/or L3 measurement should be made.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: fenghua.yu@intel.com
Cc: tony.luck@intel.com
Cc: peterz@infradead.org
Cc: acme@kernel.org
Cc: gavin.hindman@intel.com
Cc: jithu.joseph@intel.com
Cc: dave.hansen@intel.com
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/fc24e728b446404f42c78573c506e98cd0599873.1537468643.git.reinette.chatre@intel.com
A perf event has many attributes that are maintained in a separate
structure that should be provided when a new perf_event is created.
In preparation for the transition to perf_events the required attribute
structures are created for all the events that may be used in the
measurements. Most attributes for all the events are identical. The
actual configuration, what specifies what needs to be measured, is what
will be different between the events used. This configuration needs to
be done with X86_CONFIG that cannot be used as part of the designated
initializers used here, this will be introduced later.
Although they do look identical at this time the attribute structures
needs to be maintained separately since a perf_event will maintain a
pointer to its unique attributes.
In support of patch testing the new structs are given the unused attribute
until their use in later patches.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: fenghua.yu@intel.com
Cc: tony.luck@intel.com
Cc: acme@kernel.org
Cc: gavin.hindman@intel.com
Cc: jithu.joseph@intel.com
Cc: dave.hansen@intel.com
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/1822f6164e221a497648d108913d056ab675d5d0.1537377064.git.reinette.chatre@intel.com
Local register variables were used in an effort to improve the
accuracy of the measurement of cache residency of a pseudo-locked
region. This was done to ensure that only the cache residency of
the memory is measured and not the cache residency of the variables
used to perform the measurement.
While local register variables do accomplish the goal they do require
significant care since different architectures have different registers
available. Local register variables also cannot be used with valuable
developer tools like KASAN.
Significant testing has shown that similar accuracy in measurement
results can be obtained by replacing local register variables with
regular local variables.
Make use of local variables in the critical code but do so with
READ_ONCE() to prevent the compiler from merging or refetching reads.
Ensure these variables are initialized before the measurement starts,
and ensure it is only the local variables that are accessed during
the measurement.
With the removal of the local register variables and using READ_ONCE()
there is no longer a motivation for using a direct wrmsr call (that
avoids the additional tracing code that may clobber the local register
variables).
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: fenghua.yu@intel.com
Cc: tony.luck@intel.com
Cc: acme@kernel.org
Cc: gavin.hindman@intel.com
Cc: jithu.joseph@intel.com
Cc: dave.hansen@intel.com
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/f430f57347414e0691765d92b144758ab93d8407.1537377064.git.reinette.chatre@intel.com
perf_event_read_local() is the safest way to obtain measurements
associated with performance events. In some cases the overhead
introduced by perf_event_read_local() affects the measurements and the
use of rdpmcl() is needed. rdpmcl() requires the index
of the performance counter used so a helper is introduced to determine
the index used by a provided performance event.
The index used by a performance event may change when interrupts are
enabled. A check is added to ensure that the index is only accessed
with interrupts disabled. Even with this check the use of this counter
needs to be done with care to ensure it is queried and used within the
same disabled interrupts section.
This change introduces a new checkpatch warning:
CHECK: extern prototypes should be avoided in .h files
+extern int x86_perf_rdpmc_index(struct perf_event *event);
This warning was discussed and designated as a false positive in
http://lkml.kernel.org/r/20180919091759.GZ24124@hirez.programming.kicks-ass.net
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: fenghua.yu@intel.com
Cc: tony.luck@intel.com
Cc: acme@kernel.org
Cc: gavin.hindman@intel.com
Cc: jithu.joseph@intel.com
Cc: dave.hansen@intel.com
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/b277ffa78a51254f5414f7b1bc1923826874566e.1537377064.git.reinette.chatre@intel.com
Commit
1958b5fc40 ("x86/boot: Add early boot support when running with SEV active")
can occasionally cause system resets when kexec-ing a second kernel even
if SEV is not active.
That's because get_sev_encryption_bit() uses 32-bit rIP-relative
addressing to read the value of enc_bit - a variable which caches a
previously detected encryption bit position - but kexec may allocate
the early boot code to a higher location, beyond the 32-bit addressing
limit.
In this case, garbage will be read and get_sev_encryption_bit() will
return the wrong value, leading to accessing memory with the wrong
encryption setting.
Therefore, remove enc_bit, and thus get rid of the need to do 32-bit
rIP-relative addressing in the first place.
[ bp: massage commit message heavily. ]
Fixes: 1958b5fc40 ("x86/boot: Add early boot support when running with SEV active")
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.de
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: brijesh.singh@amd.com
Cc: kexec@lists.infradead.org
Cc: dyoung@redhat.com
Cc: bhe@redhat.com
Cc: ghook@redhat.com
Link: https://lkml.kernel.org/r/20180927123845.32052-1-kasong@redhat.com
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCW6dGhgAKCRCAXGG7T9hj
vs1UAPwPSDmelfUus+P5ndRQZdK/iQWuRgQUe9Gd3RUVTfcQ7AEAljcN4/dSj7SB
hOgRlCp5WB1s5/vFF7z4jc2wtqvOPAk=
=8P9c
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Juergen writes:
"xen:
Two small fixes for xen drivers."
* tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: issue warning message when out of grant maptrack entries
xen/x86/vpmu: Zero struct pt_regs before calling into sample handling code
Thomas writes:
"A set of fixes for x86:
- Resolve the kvmclock regression on AMD systems with memory
encryption enabled. The rework of the kvmclock memory allocation
during early boot results in encrypted storage, which is not
shareable with the hypervisor. Create a new section for this data
which is mapped unencrypted and take care that the later
allocations for shared kvmclock memory is unencrypted as well.
- Fix the build regression in the paravirt code introduced by the
recent spectre v2 updates.
- Ensure that the initial static page tables cover the fixmap space
correctly so early console always works. This worked so far by
chance, but recent modifications to the fixmap layout can -
depending on kernel configuration - move the relevant entries to a
different place which is not covered by the initial static page
tables.
- Address the regressions and issues which got introduced with the
recent extensions to the Intel Recource Director Technology code.
- Update maintainer entries to document reality"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Expand static page table for fixmap space
MAINTAINERS: Add X86 MM entry
x86/intel_rdt: Add Reinette as co-maintainer for RDT
MAINTAINERS: Add Borislav to the x86 maintainers
x86/paravirt: Fix some warning messages
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Fix exclusive mode handling of MBA resource
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Do not allow pseudo-locking of MBA resource
x86/intel_rdt: Fix unchecked MSR access
x86/intel_rdt: Fix invalid mode warning when multiple resources are managed
x86/intel_rdt: Global closid helper to support future fixes
x86/intel_rdt: Fix size reporting of MBA resource
x86/intel_rdt: Fix data type in parsing callbacks
x86/kvm: Use __bss_decrypted attribute in shared variables
x86/mm: Add .bss..decrypted section to hold shared variables
I swear I would have sent it the same to Linus! The main cause for
this is that I was on vacation until two weeks ago and it took a while
to sort all the pending patches between 4.19 and 4.20, test them and
so on.
It's mostly small bugfixes and cleanups, mostly around x86 nested
virtualization. One important change, not related to nested
virtualization, is that the ability for the guest kernel to trap CPUID
instructions (in Linux that's the ARCH_SET_CPUID arch_prctl) is now
masked by default. This is because the feature is detected through an
MSR; a very bad idea that Intel seems to like more and more. Some
applications choke if the other fields of that MSR are not initialized
as on real hardware, hence we have to disable the whole MSR by default,
as was the case before Linux 4.12.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJbpPo1AAoJEL/70l94x66DdxgH/is0qe6ZBtzb6Qc0W+8mHHD7
nxIkWAs2V5NsouJ750YwRQ+0Ym407+wlNt30acdBUEoXhrnA5/TvyGq999XvCL96
upWEIxpIgbvTMX/e2nLhe4wQdhsboUK4r0/B9IFgVFYrdCt5uRXjB2G4ewxcqxL/
GxxqrAKhaRsbQG9Xv0Fw5Vohh/Ls6fQDJcyuY1EBnbMpVenq2QDLI6cOAPXncyFb
uLN6ov4GNCWIPckwxejri5XhZesUOsafrmn48sApShh4T6TrisrdtSYdzl+DGza+
j5vhIEwdFO5kulZ3viuhqKJOnS2+F6wvfZ75IKT0tEKeU2bi+ifGDyGRefSF6Q0=
=YXLw
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Paolo writes:
"It's mostly small bugfixes and cleanups, mostly around x86 nested
virtualization. One important change, not related to nested
virtualization, is that the ability for the guest kernel to trap
CPUID instructions (in Linux that's the ARCH_SET_CPUID arch_prctl) is
now masked by default. This is because the feature is detected
through an MSR; a very bad idea that Intel seems to like more and
more. Some applications choke if the other fields of that MSR are
not initialized as on real hardware, hence we have to disable the
whole MSR by default, as was the case before Linux 4.12."
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (23 commits)
KVM: nVMX: Fix bad cleanup on error of get/set nested state IOCTLs
kvm: selftests: Add platform_info_test
KVM: x86: Control guest reads of MSR_PLATFORM_INFO
KVM: x86: Turbo bits in MSR_PLATFORM_INFO
nVMX x86: Check VPID value on vmentry of L2 guests
nVMX x86: check posted-interrupt descriptor addresss on vmentry of L2
KVM: nVMX: Wake blocked vCPU in guest-mode if pending interrupt in virtual APICv
KVM: VMX: check nested state and CR4.VMXE against SMM
kvm: x86: make kvm_{load|put}_guest_fpu() static
x86/hyper-v: rename ipi_arg_{ex,non_ex} structures
KVM: VMX: use preemption timer to force immediate VMExit
KVM: VMX: modify preemption timer bit only when arming timer
KVM: VMX: immediately mark preemption timer expired only for zero value
KVM: SVM: Switch to bitmap_zalloc()
KVM/MMU: Fix comment in walk_shadow_page_lockless_end()
kvm: selftests: use -pthread instead of -lpthread
KVM: x86: don't reset root in kvm_mmu_setup()
kvm: mmu: Don't read PDPTEs when paging is not enabled
x86/kvm/lapic: always disable MMIO interface in x2APIC mode
KVM: s390: Make huge pages unavailable in ucontrol VMs
...
We met a kernel panic when enabling earlycon, which is due to the fixmap
address of earlycon is not statically setup.
Currently the static fixmap setup in head_64.S only covers 2M virtual
address space, while it actually could be in 4M space with different
kernel configurations, e.g. when VSYSCALL emulation is disabled.
So increase the static space to 4M for now by defining FIXMAP_PMD_NUM to 2,
and add a build time check to ensure that the fixmap is covered by the
initial static page tables.
Fixes: 1ad83c858c ("x86_64,vsyscall: Make vsyscall emulation configurable")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com> (Xen parts)
Cc: H Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180920025828.23699-1-feng.tang@intel.com
The handlers of IOCTLs in kvm_arch_vcpu_ioctl() are expected to set
their return value in "r" local var and break out of switch block
when they encounter some error.
This is because vcpu_load() is called before the switch block which
have a proper cleanup of vcpu_put() afterwards.
However, KVM_{GET,SET}_NESTED_STATE IOCTLs handlers just return
immediately on error without performing above mentioned cleanup.
Thus, change these handlers to behave as expected.
Fixes: 8fcc4b5923 ("kvm: nVMX: Introduce KVM_CAP_NESTED_STATE")
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Patrick Colp <patrick.colp@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add KVM_CAP_MSR_PLATFORM_INFO so that userspace can disable guest access
to reads of MSR_PLATFORM_INFO.
Disabling access to reads of this MSR gives userspace the control to "expose"
this platform-dependent information to guests in a clear way. As it exists
today, guests that read this MSR would get unpopulated information if userspace
hadn't already set it (and prior to this patch series, only the CPUID faulting
information could have been populated). This existing interface could be
confusing if guests don't handle the potential for incorrect/incomplete
information gracefully (e.g. zero reported for base frequency).
Signed-off-by: Drew Schmitt <dasch@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow userspace to set turbo bits in MSR_PLATFORM_INFO. Previously, only
the CPUID faulting bit was settable. But now any bit in
MSR_PLATFORM_INFO would be settable. This can be used, for example, to
convey frequency information about the platform on which the guest is
running.
Signed-off-by: Drew Schmitt <dasch@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on VMX Controls" in Intel SDM vol 3C, the
following check needs to be enforced on vmentry of L2 guests:
If the 'enable VPID' VM-execution control is 1, the value of the
of the VPID VM-execution control field must not be 0000H.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on VMX Controls" in Intel SDM vol 3C,
the following check needs to be enforced on vmentry of L2 guests:
- Bits 5:0 of the posted-interrupt descriptor address are all 0.
- The posted-interrupt descriptor address does not set any bits
beyond the processor's physical-address width.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In case L1 do not intercept L2 HLT or enter L2 in HLT activity-state,
it is possible for a vCPU to be blocked while it is in guest-mode.
According to Intel SDM 26.6.5 Interrupt-Window Exiting and
Virtual-Interrupt Delivery: "These events wake the logical processor
if it just entered the HLT state because of a VM entry".
Therefore, if L1 enters L2 in HLT activity-state and L2 has a pending
deliverable interrupt in vmcs12->guest_intr_status.RVI, then the vCPU
should be waken from the HLT state and injected with the interrupt.
In addition, if while the vCPU is blocked (while it is in guest-mode),
it receives a nested posted-interrupt, then the vCPU should also be
waken and injected with the posted interrupt.
To handle these cases, this patch enhances kvm_vcpu_has_events() to also
check if there is a pending interrupt in L2 virtual APICv provided by
L1. That is, it evaluates if there is a pending virtual interrupt for L2
by checking RVI[7:4] > VPPR[7:4] as specified in Intel SDM 29.2.1
Evaluation of Pending Interrupts.
Note that this also handles the case of nested posted-interrupt by the
fact RVI is updated in vmx_complete_nested_posted_interrupt() which is
called from kvm_vcpu_check_block() -> kvm_arch_vcpu_runnable() ->
kvm_vcpu_running() -> vmx_check_nested_events() ->
vmx_complete_nested_posted_interrupt().
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX cannot be enabled under SMM, check it when CR4 is set and when nested
virtualization state is restored.
This should fix some WARNs reported by syzkaller, mostly around
alloc_shadow_vmcs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions
kvm_load_guest_fpu()
kvm_put_guest_fpu()
are only used locally, make them static. This requires also that both
functions are moved because they are used before their implementation.
Those functions were exported (via EXPORT_SYMBOL) before commit
e5bb40251a ("KVM: Drop kvm_{load,put}_guest_fpu() exports").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These structures are going to be used from KVM code so let's make
their names reflect their Hyper-V origin.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A VMX preemption timer value of '0' is guaranteed to cause a VMExit
prior to the CPU executing any instructions in the guest. Use the
preemption timer (if it's supported) to trigger immediate VMExit
in place of the current method of sending a self-IPI. This ensures
that pending VMExit injection to L1 occurs prior to executing any
instructions in the guest (regardless of nesting level).
When deferring VMExit injection, KVM generates an immediate VMExit
from the (possibly nested) guest by sending itself an IPI. Because
hardware interrupts are blocked prior to VMEnter and are unblocked
(in hardware) after VMEnter, this results in taking a VMExit(INTR)
before any guest instruction is executed. But, as this approach
relies on the IPI being received before VMEnter executes, it only
works as intended when KVM is running as L0. Because there are no
architectural guarantees regarding when IPIs are delivered, when
running nested the INTR may "arrive" long after L2 is running e.g.
L0 KVM doesn't force an immediate switch to L1 to deliver an INTR.
For the most part, this unintended delay is not an issue since the
events being injected to L1 also do not have architectural guarantees
regarding their timing. The notable exception is the VMX preemption
timer[1], which is architecturally guaranteed to cause a VMExit prior
to executing any instructions in the guest if the timer value is '0'
at VMEnter. Specifically, the delay in injecting the VMExit causes
the preemption timer KVM unit test to fail when run in a nested guest.
Note: this approach is viable even on CPUs with a broken preemption
timer, as broken in this context only means the timer counts at the
wrong rate. There are no known errata affecting timer value of '0'.
[1] I/O SMIs also have guarantees on when they arrive, but I have
no idea if/how those are emulated in KVM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Use a hook for SVM instead of leaving the default in x86.c - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Provide a singular location where the VMX preemption timer bit is
set/cleared so that future usages of the preemption timer can ensure
the VMCS bit is up-to-date without having to modify unrelated code
paths. For example, the preemption timer can be used to force an
immediate VMExit. Cache the status of the timer to avoid redundant
VMREAD and VMWRITE, e.g. if the timer stays armed across multiple
VMEnters/VMExits.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A VMX preemption timer value of '0' at the time of VMEnter is
architecturally guaranteed to cause a VMExit prior to the CPU
executing any instructions in the guest. This architectural
definition is in place to ensure that a previously expired timer
is correctly recognized by the CPU as it is possible for the timer
to reach zero and not trigger a VMexit due to a higher priority
VMExit being signalled instead, e.g. a pending #DB that morphs into
a VMExit.
Whether by design or coincidence, commit f4124500c2 ("KVM: nVMX:
Fully emulate preemption timer") special cased timer values of '0'
and '1' to ensure prompt delivery of the VMExit. Unlike '0', a
timer value of '1' has no has no architectural guarantees regarding
when it is delivered.
Modify the timer emulation to trigger immediate VMExit if and only
if the timer value is '0', and document precisely why '0' is special.
Do this even if calibration of the virtual TSC failed, i.e. VMExit
will occur immediately regardless of the frequency of the timer.
Making only '0' a special case gives KVM leeway to be more aggressive
in ensuring the VMExit is injected prior to executing instructions in
the nested guest, and also eliminates any ambiguity as to why '1' is
a special case, e.g. why wasn't the threshold for a "short timeout"
set to 10, 100, 1000, etc...
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_commit_zap_page() has been renamed to kvm_mmu_commit_zap_page()
This patch is to fix the commit.
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Here is the code path which shows kvm_mmu_setup() is invoked after
kvm_mmu_create(). Since kvm_mmu_setup() is only invoked in this code path,
this means the root_hpa and prev_roots are guaranteed to be invalid. And
it is not necessary to reset it again.
kvm_vm_ioctl_create_vcpu()
kvm_arch_vcpu_create()
vmx_create_vcpu()
kvm_vcpu_init()
kvm_arch_vcpu_init()
kvm_mmu_create()
kvm_arch_vcpu_setup()
kvm_mmu_setup()
kvm_init_mmu()
This patch set reset_roots to false in kmv_mmu_setup().
Fixes: 50c28f21d0
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm should not attempt to read guest PDPTEs when CR0.PG = 0 and
CR4.PAE = 1.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When VMX is used with flexpriority disabled (because of no support or
if disabled with module parameter) MMIO interface to lAPIC is still
available in x2APIC mode while it shouldn't be (kvm-unit-tests):
PASS: apic_disable: Local apic enabled in x2APIC mode
PASS: apic_disable: CPUID.1H:EDX.APIC[bit 9] is set
FAIL: apic_disable: *0xfee00030: 50014
The issue appears because we basically do nothing while switching to
x2APIC mode when APIC access page is not used. apic_mmio_{read,write}
only check if lAPIC is disabled before proceeding to actual write.
When APIC access is virtualized we correctly manipulate with VMX controls
in vmx_set_virtual_apic_mode() and we don't get vmexits from memory writes
in x2APIC mode so there's no issue.
Disabling MMIO interface seems to be easy. The question is: what do we
do with these reads and writes? If we add apic_x2apic_mode() check to
apic_mmio_in_range() and return -EOPNOTSUPP these reads and writes will
go to userspace. When lAPIC is in kernel, Qemu uses this interface to
inject MSIs only (see kvm_apic_mem_write() in hw/i386/kvm/apic.c). This
somehow works with disabled lAPIC but when we're in xAPIC mode we will
get a real injected MSI from every write to lAPIC. Not good.
The simplest solution seems to be to just ignore writes to the region
and return ~0 for all reads when we're in x2APIC mode. This is what this
patch does. However, this approach is inconsistent with what currently
happens when flexpriority is enabled: we allocate APIC access page and
create KVM memory region so in x2APIC modes all reads and writes go to
this pre-allocated page which is, btw, the same for all vCPUs.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Otherwise we may leak kernel stack for events that sample user
registers.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
The first argument to WARN_ONCE() is a condition.
Fixes: 5800dc5c19 ("x86/paravirt: Fix spectre-v2 mitigations for paravirt guests")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alok Kataria <akataria@vmware.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: virtualization@lists.linux-foundation.org
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20180919103553.GD9238@mwanda
Crypto stuff from Herbert:
"This push fixes a potential boot hang in ccp and an incorrect
CPU capability check in aegis/morus on x86."
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/aegis,morus - Do not require OSXSAVE for SSE2
crypto: ccp - add timeout support in the SEV command
In order to determine a sane default cache allocation for a new CAT/CDP
resource group, all resource groups are checked to determine which cache
portions are available to share. At this time all possible CLOSIDs
that can be supported by the resource is checked. This is problematic
if the resource supports more CLOSIDs than another CAT/CDP resource. In
this case, the number of CLOSIDs that could be allocated are fewer than
the number of CLOSIDs that can be supported by the resource.
Limit the check of closids to that what is supported by the system based
on the minimum across all resources.
Fixes: 95f0b77ef ("x86/intel_rdt: Initialize new resource group with sane defaults")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-10-git-send-email-fenghua.yu@intel.com
It is possible for a resource group to consist out of MBA as well as
CAT/CDP resources. The "exclusive" resource mode only applies to the
CAT/CDP resources since MBA allocations cannot be specified to overlap
or not. When a user requests a resource group to become "exclusive" then it
can only be successful if there are CAT/CDP resources in the group
and none of their CBMs associated with the group's CLOSID overlaps with
any other resource group.
Fix the "exclusive" mode setting by failing if there isn't any CAT/CDP
resource in the group and ensuring that the CBM checking is only done on
CAT/CDP resources.
Fixes: 49f7b4efa ("x86/intel_rdt: Enable setting of exclusive mode")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-9-git-send-email-fenghua.yu@intel.com
A loop is used to check if a CAT resource's CBM of one CLOSID
overlaps with the CBM of another CLOSID of the same resource. The loop
is run over all CLOSIDs supported by the resource.
The problem with running the loop over all CLOSIDs supported by the
resource is that its number of supported CLOSIDs may be more than the
number of supported CLOSIDs on the system, which is the minimum number of
CLOSIDs supported across all resources.
Fix the loop to only consider the number of system supported CLOSIDs,
not all that are supported by the resource.
Fixes: 49f7b4efa ("x86/intel_rdt: Enable setting of exclusive mode")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-8-git-send-email-fenghua.yu@intel.com
A system supporting pseudo-locking may have MBA as well as CAT
resources of which only the CAT resources could support cache
pseudo-locking. When the schemata to be pseudo-locked is provided it
should be checked that that schemata does not attempt to pseudo-lock a
MBA resource.
Fixes: e0bdfe8e3 ("x86/intel_rdt: Support creation/removal of pseudo-locked region")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-7-git-send-email-fenghua.yu@intel.com
When a new resource group is created, it is initialized with sane
defaults that currently assume the resource being initialized is a CAT
resource. This code path is also followed by a MBA resource that is not
allocated the same as a CAT resource and as a result we encounter the
following unchecked MSR access error:
unchecked MSR access error: WRMSR to 0xd51 (tried to write 0x0000
000000000064) at rIP: 0xffffffffae059994 (native_write_msr+0x4/0x20)
Call Trace:
mba_wrmsr+0x41/0x80
update_domains+0x125/0x130
rdtgroup_mkdir+0x270/0x500
Fix the above by ensuring the initial allocation is only attempted on a
CAT resource.
Fixes: 95f0b77ef ("x86/intel_rdt: Initialize new resource group with sane defaults")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-6-git-send-email-fenghua.yu@intel.com
When multiple resources are managed by RDT, the number of CLOSIDs used
is the minimum of the CLOSIDs supported by each resource. In the function
rdt_bit_usage_show(), the annotated bitmask is created to depict how the
CAT supporting caches are being used. During this annotated bitmask
creation, each resource group is queried for its mode that is used as a
label in the annotated bitmask.
The maximum number of resource groups is currently assumed to be the
number of CLOSIDs supported by the resource for which the information is
being displayed. This is incorrect since the number of active CLOSIDs is
the minimum across all resources.
If information for a cache instance with more CLOSIDs than another is
being generated we thus encounter a warning like:
invalid mode for closid 8
WARNING: CPU: 88 PID: 1791 at [SNIP]/arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
:827 rdt_bit_usage_show+0x221/0x2b0
Fix this by ensuring that only the number of supported CLOSIDs are
considered.
Fixes: e651901187 ("x86/intel_rdt: Introduce "bit_usage" to display cache allocations details")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-5-git-send-email-fenghua.yu@intel.com
The number of CLOSIDs supported by a system is the minimum number of
CLOSIDs supported by any of its resources. Care should be taken when
iterating over the CLOSIDs of a resource since it may be that the number
of CLOSIDs supported on the system is less than the number of CLOSIDs
supported by the resource.
Introduce a helper function that can be used to query the number of
CLOSIDs that is supported by all resources, irrespective of how many
CLOSIDs are supported by a particular resource.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-4-git-send-email-fenghua.yu@intel.com
Chen Yu reported a divide-by-zero error when accessing the 'size'
resctrl file when a MBA resource is enabled.
divide error: 0000 [#1] SMP PTI
CPU: 93 PID: 1929 Comm: cat Not tainted 4.19.0-rc2-debug-rdt+ #25
RIP: 0010:rdtgroup_cbm_to_size+0x7e/0xa0
Call Trace:
rdtgroup_size_show+0x11a/0x1d0
seq_read+0xd8/0x3b0
Quoting Chen Yu's report: This is because for MB resource, the
r->cache.cbm_len is zero, thus calculating size in rdtgroup_cbm_to_size()
will trigger the exception.
Fix this issue in the 'size' file by getting correct memory bandwidth value
which is in MBps when MBA software controller is enabled or in percentage
when MBA software controller is disabled.
Fixes: d9b48c86eb ("x86/intel_rdt: Display resource groups' allocations in bytes")
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Link: https://lkml.kernel.org/r/20180904174614.26682-1-yu.c.chen@intel.com
Link: https://lkml.kernel.org/r/1537048707-76280-3-git-send-email-fenghua.yu@intel.com
Each resource is associated with a parsing callback to parse the data
provided from user space when writing schemata file.
The 'data' parameter in the callbacks is defined as a void pointer which
is error prone due to lack of type check.
parse_bw() processes the 'data' parameter as a string while its caller
actually passes the parameter as a pointer to struct rdt_cbm_parse_data.
Thus, parse_bw() takes wrong data and causes failure of parsing MBA
throttle value.
To fix the issue, the 'data' parameter in all parsing callbacks is defined
and handled as a pointer to struct rdt_parse_data (renamed from struct
rdt_cbm_parse_data).
Fixes: 7604df6e16 ("x86/intel_rdt: Support flexible data to parsing callbacks")
Fixes: 9ab9aa15c3 ("x86/intel_rdt: Ensure requested schemata respects mode")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-2-git-send-email-fenghua.yu@intel.com
The recent removal of the memblock dependency from kvmclock caused a SEV
guest regression because the wall_clock and hv_clock_boot variables are
no longer mapped decrypted when SEV is active.
Use the __bss_decrypted attribute to put the static wall_clock and
hv_clock_boot in the .bss..decrypted section so that they are mapped
decrypted during boot.
In the preparatory stage of CPU hotplug, the per-cpu pvclock data pointer
assigns either an element of the static array or dynamically allocated
memory for the pvclock data pointer. The static array are now mapped
decrypted but the dynamically allocated memory is not mapped decrypted.
However, when SEV is active this memory range must be mapped decrypted.
Add a function which is called after the page allocator is up, and
allocate memory for the pvclock data pointers for the all possible cpus.
Map this memory range as decrypted when SEV is active.
Fixes: 368a540e02 ("x86/kvmclock: Remove memblock dependency")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Link: https://lkml.kernel.org/r/1536932759-12905-3-git-send-email-brijesh.singh@amd.com
