Now that the cci_* register access helpers are used access to
the i2c_client after probe() is no longer necessary.
Directly store a struct device *dev pointing to &client->dev inside
ov2680_dev to make the code simpler.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new comon CCI register access helpers to replace the private
register access helpers in the ov2680 driver.
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the ov2680_power_on() "sensor soft reset failed" path is hit during
probe() the WARN() about putting an enabled regulator at
drivers/regulator/core.c:2398 triggers 3 times (once for each regulator),
filling dmesg with backtraces.
Fix this by properly disabling the regulators on ov2680_power_on() errors.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ov2680_set_fmt() which == V4L2_SUBDEV_FORMAT_TRY was getting
the try_fmt v4l2_mbus_framefmt struct from the passed in sd_state
and then storing the contents of that into the return by reference
format->format struct.
While the right thing to do would be filling format->format based on
the just looked up mode and then store the results of that in
sd_state->pads[0].try_fmt .
Before the previous change introducing ov2680_fill_format() this
resulted in ov2680_set_fmt() which == V4L2_SUBDEV_FORMAT_TRY always
returning the zero-ed out sd_state->pads[0].try_fmt in format->format
breaking callers using this.
After the introduction of ov2680_fill_format() which at least
initializes sd_state->pads[0].try_fmt properly, format->format
is now always being filled with the default 800x600 mode set by
ov2680_init_cfg() independent of the actual requested mode.
Move the filling of format->format with ov2680_fill_format() to
before the if (which == V4L2_SUBDEV_FORMAT_TRY) and then store
the filled in format->format in sd_state->pads[0].try_fmt to
fix this.
Note this removes the fmt local variable because IMHO having a local
variable which points to a sub-struct of one of the function arguments
just leads to confusion when reading the code.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a ov2680_fill_format() helper function and use this everywhere were
a v4l2_mbus_framefmt struct needs to be filled in so that the driver always
fills it consistently.
This is a preparation patch for fixing ov2680_set_fmt()
which == V4L2_SUBDEV_FORMAT_TRY calls not properly filling in
the passed in v4l2_mbus_framefmt struct.
Note that for ov2680_init_cfg() this now simply always fills
the try_fmt struct of the passed in sd_state. This is correct because
ov2680_init_cfg() is never called with a NULL sd_state so the old
sd_state check is not necessary.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On ov2680_set_fmt() calls with format->which == V4L2_SUBDEV_FORMAT_TRY,
ov2680_set_fmt() does not talk to the sensor.
So in this case there is no need to lock the sensor->lock mutex or
to check that the sensor is streaming.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
VIDEO_V4L2_SUBDEV_API is now automatically selected in Kconfig
for all sensor drivers. Remove the ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
checks.
This is a preparation patch for fixing ov2680_set_fmt()
which == V4L2_SUBDEV_FORMAT_TRY calls not properly filling in
the passed in v4l2_mbus_framefmt struct.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ov2680_vflip_disable() / ov2680_hflip_disable() pass BIT(0) instead of
0 as value to ov2680_mod_reg().
While fixing this also:
1. Stop having separate enable/disable functions for hflip / vflip
2. Move the is_streaming check, which is unique to hflip / vflip
into the ov2680_set_?flip() functions.
for a nice code cleanup.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The index into ov2680_hv_flip_bayer_order[] should be 0-3, but
ov2680_bayer_order() was using 0 + BIT(2) + (BIT(2) << 1) as
max index, while the intention was to use: 0 + 1 + 2 as max index.
Fix the index calculation in ov2680_bayer_order(), while at it
also just use the ctrl values rather then reading them back using
a slow i2c-read transaction.
This also allows making the function void, since there now are
no more i2c-reads to error check.
Note the check for the ctrls being NULL is there to allow
adding an ov2680_fill_format() helper later, which will call
ov2680_set_bayer_order() during probe() before the ctrls are created.
[Sakari Ailus: Change all users of ov2680_set_bayer_order() here]
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Quoting the OV2680 datasheet:
"3.2 exposure and gain control
In the OV2680, the exposure time and gain are set manually from an external
controller. The OV2680 supports manual gain and exposure control only for
normal applications, no auto mode."
And indeed testing with the atomisp_ov2680 fork of ov2680.c has shown that
auto-exposure and auto-gain do not work.
Note that the code setting the auto-exposure flag was broken, callers
of ov2680_exposure_set() were directly passing !!ctrls->auto_exp->val as
"bool auto_exp" value, but ctrls->auto_exp is a menu control with:
enum v4l2_exposure_auto_type {
V4L2_EXPOSURE_AUTO = 0,
V4L2_EXPOSURE_MANUAL = 1,
...
So instead of passing !!ctrls->auto_exp->val they should have been passing
ctrls->auto_exp->val == V4L2_EXPOSURE_AUTO, iow the passed value was
inverted of what it should have been.
Also remove ov2680_g_volatile_ctrl() since without auto support the gain
and exposure controls are not volatile.
This also fixes the control values not being properly applied in
ov2680_mode_set(). The 800x600 mode register-list also sets gain,
exposure and vflip overriding the last set ctrl values.
ov2680_mode_set() does call ov2680_gain_set() and ov2680_exposure_set()
but did this before writing the mode register-list, so these values
would still be overridden by the mode register-list.
Add a v4l2_ctrl_handler_setup() call after writing the mode register-list
to restore all ctrl values. Also remove the ctrls->gain->is_new check from
ov2680_gain_set() so that the gain always gets restored properly.
Last since ov2680_mode_set() now calls v4l2_ctrl_handler_setup(), remove
the v4l2_ctrl_handler_setup() call after ov2680_mode_restore() since
ov2680_mode_restore() calls ov2680_mode_set().
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add mention that successful VIDIOC_SUBDEV_G_ROUTING call will update
'num_routes' and remove mention about non-existing streams, which is
incorrect.
Fixes: ea73eda508 ("media: Documentation: Add GS_ROUTING documentation")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The initial state of RESETB input signal of OV5640 should be
asserted, i.e. the sensor should be in reset. This is not the
case, make it so.
Since the subsequent assertion of RESETB signal is no longer
necessary and the timing of the power sequencing could be
slightly adjusted, add annotations to the delays which match
OV5640 datasheet rev. 2.03, both:
figure 2-3 power up timing with internal DVDD
figure 2-4 power up timing with external DVDD source
The 5..10ms delay between PWDN assertion and RESETB assertion
is not even documented in the power sequencing diagram, and
with this reset fix, it is no longer even necessary.
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is no possible for platform_get_irq() to return 0,
and the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is not possible for platform_get_irq() or platform_get_irq_byname()
to return 0. Use the return value from platform_get_irq()
or platform_get_irq_byname().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set OV5640_REG_IO_MIPI_CTRL00 bit 2 to 1 instead of 0, since 1 means
MIPI CSI2 interface, while 0 means CPI parallel interface.
In the ov5640_set_power_mipi() the interface should obviously be set
to MIPI CSI2 since this functions is used to power up the sensor when
operated in MIPI CSI2 mode. The sensor should not be in CPI mode in
that case.
This fixes a corner case where capturing the first frame on i.MX8MN
with CSI/ISI resulted in corrupted frame.
Fixes: aa4bb8b883 ("media: ov5640: Re-work MIPI startup sequence")
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> # [Test on imx6q]
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Jai Luthra <j-luthra@ti.com> # [Test on bplay, sk-am62]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Previously on ACPI platforms, sensors that are intended to be connected
to an IPU device for use with the ipu3-cio2 driver lacking the necessary
connection information in firmware. IPU bridge driver is to connect
sensors to IPU device via software nodes.
Currently IVSC located between IPU device and sensors is available in
existing commercial platforms from multiple OEMs. But the connection
information between them in firmware is also not enough to build V4L2
connection graph. This patch parses the connection properties from the
SSDB buffer in DSDT and build the connection using software nodes.
IVSC driver is based on MEI framework (previously known as HECI), it
has two MEI clients, MEI CSI and MEI ACE. Both clients are used to
communicate messages with IVSC firmware. Linux abstracts MEI client
as a device, whose bus type is MEI. And the device is addressed by a
GUID/UUID which is part of the device name of MEI client. After figured
out MEI CSI via the UUID composed device name, this patch setup the
connection between MEI CSI and IPU, and the connection between MEI CSI
and sensor via software nodes.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ACE is a submodule of IVSC which controls camera sensor's
ownership, belonging to host or IVSC. When IVSC owns camera
sensor, it is for algorithm computing. When host wants to
control camera sensor, ACE module needs to be informed of
ownership with defined interface.
The interface is via MEI. There is a separate MEI UUID, which
this driver uses to enumerate.
To switch ownership of camera sensor between IVSC and host,
the caller specifies the defined ownership information which
will be sent to firmware by sending MEI command.
Device link(device_link_add) is used to set the right camera
sensor ownership before accessing the sensor via I2C. With
DL_FLAG_PM_RUNTIME and DL_FLAG_RPM_ACTIVE, the supplier device
will be PM runtime resumed before the consumer(camera sensor).
So use runtime PM callbacks to transfer the ownership between
host and IVSC.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
CSI is a submodule of IVSC which can route camera sensor data
to the outbound MIPI CSI-2 interface.
The interface communicating with firmware is via MEI. There is
a separate MEI UUID, which this driver uses to enumerate.
To route camera sensor data to host, the information of link
frequency and number of data lanes is sent to firmware by
sending MEI command when starting stream.
CSI also provides a privacy mode. When privacy mode is turned
on, camera sensor can't be used. This means that both IVSC and
host Image Processing Unit(IPU) can't get image data. And when
this mode is turned on, user is notified via v4l2 control
callback.
Link: https://lore.kernel.org/linux-media/20230803115550.1601965-2-sakari.ailus@linux.intel.com
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a driver for the DW9719 VCM. The driver creates a v4l2 subdevice
and registers a control to set the desired focus.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fill sensor->vcm_type and call intel_cio2_bridge_instantiate_vcm() from
the v4l2-async bound op so that an I2C-client will be instatiated for
the VCM.
Note unfortunately on atomisp the _DSM to get the VCM type sometimes
returns a VCM even though there is none. Since VCMs are typically only
used together with certain sensors, work around this by adding a vcm
field to atomisp_sensor_config and only check for a VCM when that is set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
acpi_handle_info() uses the ACPI path to the handle as prefix for messages
e.g. : "\_SB_.I2C2.CAM8".
This makes it hard for users to figure out which csi2-bridge messages
belong to which sensor since the actual sensor drivers uses the ACPI
device name (typically "HID:00") for logging.
Extend the acpi_handle_info() (and err and warn) logging to also log
the device name to make it easier to match csi2-bridge messages with
sensor driver log messages.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove the duplicate IPU ACPI bridge code and use the new
shared ipu_bridge_init() functionality.
Note this will also use / assume v4l2-async device instantiation for
ov5693 sensors on atomisp devices since ipu_supported_sensors[]
already contains a match for this.
This is fine since recent atomisp improvements allow the atomisp code
to work with generic v4l2 sensor drivers and using an unmodified
drivers/media/i2c/ov5693.c has been successfully tested on
an Acer Iconia W4 820 tablet with an ISP2400 + OV5693 sensor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In most cases when a VCM is used there is a single integrated module
with the sensor + VCM + lens. This means that the sensor and VCM often
share regulators and possibly also something like a powerdown pin.
In the ACPI tables this is modelled as a single ACPI device with
multiple I2cSerialBus resources.
On atomisp devices the regulators and clks are modelled as ACPI
power-resources, which are controlled by the (ACPI) power state
of the sensor. So the sensor must be in D0 power state for the VCM
to work.
To make this work add a device-link with DL_FLAG_PM_RUNTIME flag
so that the sensor will automatically be runtime-resumed whenever
the VCM is runtime-resumed.
This requires the probing of the VCM and thus the creation of the VCM
I2C-client to be delayed till after the sensor driver has bound.
Move the instantiation of the VCM I2C-client to the v4l2_async_notifier
bound op, so that it is done after the sensor driver has bound; and
add code to add the device-link.
This fixes the problem with the shared ACPI power-resources on atomisp2
and this avoids the need for VCM related workarounds on IPU3 / IPU6.
E.g. until now the dw9719 driver needed to get and control a Vsio
(V sensor IO) regulator since that needs to be enabled to enable I2C
pass-through on the PMIC on the sensor module. So the driver was
controlling this regulator even though the actual dw9719 chip has no
Vsio pin / power-plane.
This also removes the need for ipu_bridge_init() to return
-EPROBE_DEFER since the VCM is now instantiated later.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The GalaxyCore GC0310 is used together with the atomisp on various
devices, add it to ipu_supported_sensors[].
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move ipu-bridge.h to include/media/, so that it can also be used by
the atomisp code.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a parse_sensor_fwnode() callback to ipu_bridge_init(), so that
ipu_bridge_init() can be used with other sensor fwnode parse functions
then just ipu_bridge_parse_ssdb().
This will allow the ipu3-bridge code to also be used by the atomisp
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
sensor->adev is no longer dereferenced before it is permanently set by:
sensor->adev = acpi_dev_get(adev);
So the early assignment with a borrowed reference can be dropped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The code to go from ACPI sensor info to a fwnode-tree with connector
nodes and endpoint properties is 99% the same for the atomisp2 and
the IPU3.
The main difference is that atomisp2 devices do not have a SSDB table
with various info.
Abstract out the parsing of the sensor's ACPI fwnode into a helper
function and store the parsed results, rather then the raw SSDB
in struct ipu_sensor.
This is a preparation patch for making the ipu-bridge code more generic
so that it can be shared with the atomisp driver.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is no need to keep a reference to the PLD struct around,
it is only used once the get the sensor orientation.
Make ipu_bridge_parse_orientation() also get + put the PLD.
This is a preparation patch for making the ipu-bridge code more generic
so that it can be shared with the atomisp driver.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Store the dev pointer in struct ipu_bridge instead of passing it
around 3 levels deep.
This takes up slightly more memory but further patches in this series
add more data which needs to be passed around making passing
everything as arguments cumbersome and those further patches also
add data to struct ipu_bridge.
To be consistent with these upcoming patches also add
the dev pointer to struct ipu_bridge.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move initialization of node_names.vcm to ipu_bridge_init_swnode_names()
where it belongs.
And make the initialization of nodes[SWNODE_VCM] unconditional,
ipu_bridge_init_swnode_group() takes care of not registering it
when there is no VCM.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move initialization of node_names.vcm to ipu_bridge_init_swnode_names()
where it belongs.
And make the initialization of nodes[SWNODE_VCM] unconditional,
ipu_bridge_init_swnode_group() takes care of not registering it
when there is no VCM.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit 567f97bd38 ("media: ipu3-cio2: support multiple sensors and VCMs
with same HID") introduced an on stack vcm_name and then uses this for
the name field of the software_node struct used for the vcm.
But the software_node struct is much longer lived then the current
stack-frame, so this is no good.
Instead extend the ipu_node_names struct with an extra field to store
the vcm software_node name and use that.
Note this also changes the length of the allocated buffer from
ACPI_ID_LEN + 4 to 16. the name is filled with "<ipu_vcm_types[x]>-%u"
where ipu_vcm_types[x] is not an ACPI_ID. The maximum length of
the strings in the ipu_vcm_types[] array is 11 + 5 bytes for "-255\0"
means 16 bytes are needed in the worst case scenario.
Fixes: 567f97bd38 ("media: ipu3-cio2: support multiple sensors and VCMs with same HID")
Cc: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When ipu_bridge_parse_rotation() and ipu_bridge_parse_orientation() run
sensor->adev is not set yet.
So if either of the dev_warn() calls about unknown values are hit this
will lead to a NULL pointer deref.
Set sensor->adev earlier, with a borrowed ref to avoid making unrolling
on errors harder, to fix this.
Fixes: 485aa3df0d ("media: ipu3-cio2: Parse sensor orientation and rotation")
Cc: Fabian Wüthrich <me@fabwu.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace a goto-based loop by a while loop.
Suggested-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for C-PHY on R-Car V4H. While the V4H supports both D-PHY
and C-PHY this patch only adds support for the C-PHY mode due to lack of
documentation and hardware to test on.
The V4H is the first Gen4 device that is enabled in the rcar-csi2
driver. There is much overlap with the Gen3 driver, the primary
difference is in how the receiver is started. The V4H have a much larger
register space and some addresses overlap with Gen3.
[Sakari Ailus: Use div_u64() to divide a 64-bit integer.]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx219_set_pad_format() function adjusts the media bus code provided
through the v4l2_subdev_format parameter to a media bus code known
to be supported by the sensor.
The same exact operation is performed by the imx219_get_format_code()
function which called by imx219_update_pad_format(), which is in the
imx219_set_pad_format() call path.
Remove the duplicated operation and simplify imx219_set_pad_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The set_fmt and init_cfg functions both fills a v4l2_mbus_framefmt
instance, passing in the mode and the media bus code. While set_fmt
uses function helpers, init_cfg open-codes the assignments.
Simplify the format initialization by moving it to a common helper.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Port the imx219 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX219 is a RAW sensor. Fix the colorspace configuration by
using V4L2_COLORSPACE_RAW and adjust the quantization and transfer
function values. Drop ycbcr_enc as it doesn't apply to RAW sensors.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Complete the default format initialization in init_cfg() filling in
the fields for the colorspace configuration copied from
imx219_set_default_format().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the init_cfg pad level operation instead of the internal subdev
open operation to set default formats on the pads.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx219 is using the name "codes" for the mbus formats array. The
name is too generic and not easy to read and follow in the code. Change
it to imx219_mbus_formats.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The helpers in this header are not used anywhere anymore,
they have been superseded by the new CCI register access helpers.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new comon CCI register access helpers to replace the private
register access helpers in the ov2680 driver.
While at it also switch to using the same register address defines
as the standard drivers/media/i2c/ov2680.c driver to make merging
the 2 drivers simpler.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new comon CCI register access helpers to replace the private
register access helpers in the imx290 driver.
[Sakari Ailus: Squashed the patch to address a merge issue in Kconfig]
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new comon CCI register access helpers to replace the private
register access helpers in the ov5693 driver.
[Sakari Ailus: Squashed the patch to address a merge issue in Kconfig]
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The CSI2 specification specifies a standard method to access camera sensor
registers called "Camera Control Interface (CCI)".
This uses either 8 or 16 bit (big-endian wire order) register addresses
and supports 8, 16, 24 or 32 bit (big-endian wire order) register widths.
Currently a lot of Linux camera sensor drivers all have their own custom
helpers for this, often copy and pasted from other drivers.
Add a set of generic helpers for this so that all sensor drivers can
switch to a single common implementation.
These helpers take an extra optional "int *err" function parameter,
this can be used to chain a bunch of register accesses together with
only a single error check at the end, rather than needing to error
check each individual register access. The first failing call will
set the contents of err to a non 0 value and all other calls will
then become no-ops.
Link: https://lore.kernel.org/linux-media/59aefa7f-7bf9-6736-6040-39551329cd0a@redhat.com/
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
