Add st,min-sample-time-nsecs to channel generic binding.
Sample time can be defined par channel node. If a channel
is configured as differential, the same sample time applies
for both inputs.
Keep support of legacy st,min-sample-time-nsecs property
for backward compatibility.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-8-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of vrefint calibration.
If a channel is labeled as vrefint, get vrefint calibration
from non volatile memory for this channel.
vrefint channel is exposed as a processed channel returning
the actual value of vrefp:
vrefp = 3.3 x vrefint_cal / vrefint_data
A conversion on vrefint channel allows to update scale
factor according to vrefint deviation, compared to vrefint
calibration value.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-7-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of ADC2 internal channels VDDCORE, VREFINT and VBAT.
The reserved label name "vddcore", "vrefint" and "vbat" must
be used in Device Tree channel node, to enable the corresponding
internal channel.
Note: This patch does not provide support of internal channels
for F4 and H7.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-6-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of generic IIO channel binding:
./devicetree/bindings/iio/adc/adc.yaml
Keep support of st,adc-channels and st,adc-diff-channels
for backward compatibility.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-5-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Split stm32_adc_chan_of_init channel initialization function into
several routines to increase readability and prepare channel
generic binding handling.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-4-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of nvmem. This allows to retrieve calibration data from OTP
for vrefint internal channel.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211014131228.4692-3-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ADC generic channel binding. This binding should
be used as an alternate to legacy channel properties
whenever possible.
ADC generic channel binding allows to identify supported
internal channels through the following reserved label names:
"vddcore", "vrefint" and "vbat".
This binding also allows to set a different sampling time
for each channel.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211014131228.4692-2-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Whilst nice to get rid of this non obvious code, this also clears a
static checker warning:
drivers/iio/accel/sca3000.c:734 sca3000_read_raw()
warn: no-op. '((*val) << 19) >> 19'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211017160303.72441-1-jic23@kernel.org
Since commit 2a9685d1a3 ("iio: adc: xilinx: use more devres helpers and
remove remove()") the `irq` field from XADC driver state struct is only
used in the `probe()` function.
Use the local `irq` variable throughout the `probe()` function and remove
the now unused field from the state struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211017121551.24063-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The length of hw->settings->odr_table is 2 and ref_sensor->id is an enum
variable whose value is between 0 and 5.
However, the value ST_LSM6DSX_ID_MAX (i.e. 5) is not caught properly in
switch (sensor->id) {
If ref_sensor->id is ST_LSM6DSX_ID_MAX, an array overflow will ocurrs in
function st_lsm6dsx_check_odr():
odr_table = &sensor->hw->settings->odr_table[sensor->id];
and in function st_lsm6dsx_set_odr():
reg = &hw->settings->odr_table[ref_sensor->id].reg;
To avoid this array overflow, handle ST_LSM6DSX_ID_GYRO explicitly and
return -EINVAL for the default case.
The enum value ST_LSM6DSX_ID_MAX is only present as an easy way to check
the limit and as such is never used, however this is not locally obvious.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20211011114003.976221-1-starmiku1207184332@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092656.421-3-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211008092656.421-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-9-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-8-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
BTW, change the return value from 'ENXIO' to 'ENODEV',
perfer ENODEV which means no such device.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211008092858.495-7-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> #Meson8b Odroid-C1
Link: https://lore.kernel.org/r/20211008092858.495-6-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-5-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-4-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-3-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When !iio_buffer_space_available(rb) is true and signal_pending(current)
is false the end of the do-while loop is reached and the uninitialized
variable ret is zero checked. Fix this by initializing variable ret to
zero.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 9eeee3b0bf ("iio: Add output buffer support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211015153254.33783-1-colin.king@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The remove function and the goto sections are not necessary if devm
functions are used.
Convert device register to devm version. Add hook functions to release
device resources, and use them inside probe with devm_add_action,
which will release resources on driver detach.
To maintain the order of which device resources were released/reseted,
register the hook functions as soon as resources are obtained/initialized.
Since devres actions are called on driver detach, the remove
function and the error-handling goto sections are no longer necessary.
Signed-off-by: André Gustavo Nakagomi Lopez <andregnl@usp.br>
Link: https://lore.kernel.org/r/YWnMsGlc/I35gYvy@Andryuu.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add of_device_id table so the driver can be used on DT platforms without
relying on i2c_device_id fallback. (So DT schema validation is possible)
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20211006163058.145842-4-nikita@trvn.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On some platforms the supply regulators must be enabled before the
sensor can work. Add vdd and vddio regulators for the sensor and IO bus
power respectively.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20211006163058.145842-3-nikita@trvn.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since Hemant is not carrying out any maintainership duties let's make
him as a dedicated reviewer. Also add the new mailing lists dedicated
for MHI in subspace mailing list server.
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20211019133901.173966-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmFudVERHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0Foiepg//R5DRm1gMFGP/dl2P8u6KD2oXNmbqc3J0
+EPRTkyTyawQzc21wdxUh3oObgxmDS6P7Cr17z9viGse2PsUjza4Sptic3Zqi3Kv
FzeXZaP0GY9nC+hAyz+dSkMKNw19mkCYYEIWhDwYFpXMiOV8QlT+6pFgOiffofeR
GYMUoV2XeuxR6OH0zMOuYKTzjOCYC+VJTP4BfeUetpRZQyllgFOA+5KX4ZWTiJMV
eGCaq3Hhn6IQa7ATgYUBYJyMkAXQDrKDaMxiaCIuh/k3bgjAkfhkV48mu2cHTsX9
v0q21JkgmBenwNP/OQ6mxmWR9SFY4eB22Ptkd1foTPjAsqoST7qmqEBhhLrRb/fB
HkL0I7M4tWDqSTJKgdn+UHYrKFW9oBHIt5SK1tCS+zTYIn1wEmkY/w/9MuZllBFO
VKu5q2ypf/yGgCqPIZilK69mrZd7/72rE6tr3oefUF2iUVLdh9fI1TjGGyoT6GZ5
ZlEIfGHRpcRGHFiA4e+6tTx9VLr8m1B5YVvBWWPlruYe8ep7MmD3KjUcwINiRyNs
5rdBl2RI8VAUBbQ+60VWn03e/0kuRESpFC3Gf/ng+6hRSUbRFe4lZw60GbyFDXwV
m1odTlkXA7l6oRG9f5COhE/oNO7dsfMO74W6+yzhWICnxjgJFosaaZTLw8F9QJdS
m3z9tSU84js=
=htmG
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of IIO new device and feature support for the 5.16 cycle
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
* tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (148 commits)
iio: imx8qxp-adc: mark PM functions as __maybe_unused
iio: pressure: ms5611: Make ms5611_remove() return void
iio: potentiometer: max5487: Don't return an error in .remove()
iio: magn: hmc5843: Make hmc5843_common_remove() return void
iio: health: afe4403: Don't return an error in .remove()
iio: dac: ad5686: Make ad5686_remove() return void
iio: dac: ad5592r: Make ad5592r_remove() return void
iio: dac: ad5446: Make ad5446_remove() return void
iio: dac: ad5380: Make ad5380_remove() return void
iio: accel: mma7455: Make mma7455_core_remove() return void
iio: accel: kxsd9: Make kxsd9_common_remove() return void
iio: accel: bmi088: Make bmi088_accel_core_remove() return void
iio: accel: bmc150: Make bmc150_accel_core_remove() return void
iio: accel: bma400: Make bma400_remove() return void
drivers:iio:dac:ad5766.c: Add trigger buffer
iio: triggered-buffer: extend support to configure output buffers
iio: kfifo-buffer: Add output buffer support
iio: Add output buffer support
iio: documentation: Document scd4x calibration use
drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor
...
This removes the chrdev_lock from the counter subsystem. This was
intended to prevent opening the chrdev more than once. However, this
doesn't work in practice since userspace can duplicate file descriptors
and pass file descriptors to other processes. Since this protection
can't be relied on, it is best to just remove it.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20211017185521.3468640-1-david@lechnology.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the counter subsystem, we are already using sysfs_emit(), but there
were a few places where we were still using sprintf() in *_show()
functions. For consistency and added protections, use sysfs_emit()
everywhere.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20211017190106.3472645-1-david@lechnology.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When endpoint_alloc() return failed in xillyusb_setup_base_eps(),
'xdev->msg_ep' will be freed but not set to NULL. That lets program
enter fail handling to cleanup_dev() in xillyusb_probe(). Check for
'xdev->msg_ep' is invalid in cleanup_dev() because 'xdev->msg_ep' did
not set to NULL when was freed. So the UAF problem for 'xdev->msg_ep'
is triggered.
==================================================================
BUG: KASAN: use-after-free in fifo_mem_release+0x1f4/0x210
CPU: 0 PID: 166 Comm: kworker/0:2 Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? fifo_mem_release+0x1f4/0x210
kasan_report.cold+0x7f/0x11b
? xillyusb_probe+0x530/0x700
? fifo_mem_release+0x1f4/0x210
fifo_mem_release+0x1f4/0x210
? __sanitizer_cov_trace_pc+0x1d/0x50
endpoint_dealloc+0x35/0x2b0
cleanup_dev+0x90/0x120
xillyusb_probe+0x59a/0x700
...
Freed by task 166:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
xillyusb_probe+0x606/0x700
Set 'xdev->msg_ep' to NULL after being freed in xillyusb_setup_base_eps()
to fix the UAF problem.
Fixes: a53d1202ae ("char: xillybus: Add driver for XillyUSB (Xillybus variant for USB)")
Cc: stable <stable@vger.kernel.org>
Acked-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211016052047.1611983-1-william.xuanziyang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When freeing txn buffers, binder_transaction_buffer_release()
attempts to detect whether the current context is the target by
comparing current->group_leader to proc->tsk. This is an unreliable
test. Instead explicitly pass an 'is_failure' boolean.
Detecting the sender was being used as a way to tell if the
transaction failed to be sent. When cleaning up after
failing to send a transaction, there is no need to close
the fds associated with a BINDER_TYPE_FDA object. Now
'is_failure' can be used to accurately detect this case.
Fixes: 44d8047f1d ("binder: use standard functions to allocate fds")
Cc: stable <stable@vger.kernel.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211015233811.3532235-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add a new uAPI (under the memory ioctl) to request from the driver
to export a DMA-BUF object that represents a memory region on
the device's DRAM. This is needed to enable peer-to-peer over PCIe
between habana device and an RDMA adapter (e.g. mlnx5 or efa
rdma adapter).
- Add debugfs node to dynamically configure CS timeout. Up until now,
it was only configurable through kernel module parameter.
- Fetch more comprehensive power information from the firmware.
- Always take timestamp when waiting for user interrupt, as the user
needs that information to optimize the graph runtime compilation.
- Modify user interrupt to look on 64-bit user value as fence, instead
of 32-bit.
- Bypass reset in case of repeated h/w error event after device reset.
This is to prevent endless loop of resets to the device.
- Fix several bugs in multi CS completion code.
- Fix race condition in fd close/open.
- Update to latest firmware headers
- Add select CRC32 in kconfig
- Small fixes, cosmetics
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE7TEboABC71LctBLFZR1NuKta54AFAmFtPa4ACgkQZR1NuKta
54A9NAf/QJOc72XhqinNm62RvUoZQehNyDFHcYYBORqIpC+/NsggWwy0VdrDHSeg
uXmt6qwRUCc1+tOjOcFD/b6pnwz16mEqQrmVO8XiZOiCvIGcDEapq0HqGfEXwYtv
NcQ+k682qqXlza6SCZS9/webJzRuhHwxdFP9HTEYLhKmHoOgBza63F6dreku/fEG
mCDVtnMbo8Sa98657Jz3yTElhA+JPsDYO6PycZUTGdPn38mzz5Y5o6Ds8SshIXbr
ZQQxHope7NkqcnfYQ8nIoyl7bPLBv2NaqNz216+sBVVy+kHx6f1+FJ4hJM+PHi20
CuOiUgVBRKp2LJ2k0HoITy5XiXe/Cg==
=bzK+
-----END PGP SIGNATURE-----
Merge tag 'misc-habanalabs-next-2021-10-18' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux into char-misc-next
Oded writes:
This tag contains habanalabs driver changes for v5.16:
- Add a new uAPI (under the memory ioctl) to request from the driver
to export a DMA-BUF object that represents a memory region on
the device's DRAM. This is needed to enable peer-to-peer over PCIe
between habana device and an RDMA adapter (e.g. mlnx5 or efa
rdma adapter).
- Add debugfs node to dynamically configure CS timeout. Up until now,
it was only configurable through kernel module parameter.
- Fetch more comprehensive power information from the firmware.
- Always take timestamp when waiting for user interrupt, as the user
needs that information to optimize the graph runtime compilation.
- Modify user interrupt to look on 64-bit user value as fence, instead
of 32-bit.
- Bypass reset in case of repeated h/w error event after device reset.
This is to prevent endless loop of resets to the device.
- Fix several bugs in multi CS completion code.
- Fix race condition in fd close/open.
- Update to latest firmware headers
- Add select CRC32 in kconfig
- Small fixes, cosmetics
* tag 'misc-habanalabs-next-2021-10-18' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux: (25 commits)
habanalabs: refactor fence handling in hl_cs_poll_fences
habanalabs: context cleanup cosmetics
habanalabs: simplify wait for interrupt with timestamp flow
habanalabs: initialize hpriv fields before adding new node
habanalabs: Unify frequency set/get functionality
habanalabs: select CRC32
habanalabs: add support for dma-buf exporter
habanalabs: define uAPI to export FD for DMA-BUF
habanalabs: fix NULL pointer dereference
habanalabs: fix race condition in multi CS completion
habanalabs: use only u32
habanalabs: update firmware files
habanalabs: bypass reset for continuous h/w error event
habanalabs: take timestamp on wait for interrupt
habanalabs: prevent race between fd close/open
habanalabs: refactor reset log message
habanalabs: define soft-reset as inference op
habanalabs: fix debugfs device memory MMU VA translation
habanalabs: add support for a long interrupt target value
habanalabs: remove redundant cs validity checks
...
Without CONFIG_PM_SLEEP, the runtime suspend/resume functions
are unused, producing a warning:
drivers/iio/adc/imx8qxp-adc.c:433:12: error: 'imx8qxp_adc_runtime_resume' defined but not used [-Werror=unused-function]
433 | static int imx8qxp_adc_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/iio/adc/imx8qxp-adc.c:419:12: error: 'imx8qxp_adc_runtime_suspend' defined but not used [-Werror=unused-function]
419 | static int imx8qxp_adc_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Mark them as __maybe_unused to shut up the compiler.
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211013144338.2261316-1-arnd@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now ms5611_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The only effect of returning an error in an spi .remove() callback is
that the spi core issues a generic warning message. Instead emit a more
specific error message and return 0 to not report the same issue twice.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now hmc5843_common_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The only effect of returning an error in an spi .remove() callback is
that the spi core issues another warning message. Don't report the same
problem twice and return 0 unconditionally instead. Also degrade the log
level to warning, as nothing really bad is expected from a failure to
put the device in suspend mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now ad5686_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now ad5592r_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now ad5446_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now ad5380_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now mma7455_core_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now kxsd9_common_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now bmi088_accel_core_remove() returns zero unconditionally. Make
it return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Up to now bmc150_accel_core_remove() returns zero unconditionally. Make
it return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an i2c or spi driver's remove function returns a non-zero error
code nothing happens apart from emitting a generic error message. Make
this error message more device specific and return zero instead in the
remove callbacks. As the return value of bma400_remove() is unused then,
change the function to not yield a return value.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211013203223.2694577-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This chip is able to generate waveform and using an
with the output trigger buffer will be easy to generate one.
Signed-off-by: Mihail Chindris <mihail.chindris@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211007080035.2531-7-mihail.chindris@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that output (kfifo) buffers are supported, we need to extend the
{devm_}iio_triggered_buffer_setup_ext() parameter list to take a direction
parameter.
This allows us to attach an output triggered buffer to a DAC device.
Unfortunately it's a bit difficult to add another macro to avoid changing 5
drivers where {devm_}iio_triggered_buffer_setup_ext() is used.
Well, it's doable, but may not be worth the trouble vs just updating all
these 5 drivers.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Mihail Chindris <mihail.chindris@analog.com>
Link: https://lore.kernel.org/r/20211007080035.2531-4-mihail.chindris@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
