Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add radar_detect_widths to the interface combination that allows
concurrent P2P Device dedicated interface and AP interfaces, to enable
testing of radar detection when P2P Device interface is used.
Clear the radar_detect_widths in case of multi channel contexts
as this is not currently supported.
As radar_detect_widths are now supported in all combinations,
remove the hwsim_if_dfs_limits definition since it is no longer
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add API to support VHT MU-MIMO air sniffer.
in MU-MIMO there are parallel frames on the air while the HW
has only one RX.
add the capability to sniff one of the MU-MIMO parallel frames by
giving the sniffer additional information so it'll know which
of the parallel frames it shall follow.
Add attribute - NL80211_ATTR_MU_MIMO_GROUP_DATA - for getting
a MU-MIMO groupID in order to monitor packets from that group
using VHT MU-MIMO.
And add attribute -NL80211_ATTR_MU_MIMO_FOLLOW_ADDR - for passing
MAC address to monitor mode.
that option will be used by VHT MU-MIMO air sniffer to follow a
station according to it's MAC address using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of handling ADDBA Request while a session
is already active with the peer is wrong - in case the peer is using
the existing session's dialog token this should be treated as update
to the session, which can update the timeout value.
We don't really have a good way of supporting that, so reject, but
implement the required behaviour in the spec of "Even if the updated
ADDBA Request frame is not accepted, the original Block ACK setup
remains active." (802.11-2012 10.5.4)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've accumulated a couple of different fixes now to mesh_sta_cleanup()
due to the different paths that user_mpm and !user_mpm cases take -- one
fix to flush nexthop paths and one to fix the counting.
The only caller of mesh_plink_deactivate() is mesh_sta_cleanup(), so we
can push the user_mpm checks down into there in order to share more
code.
In doing so, we can remove an extra call to mesh_path_flush_by_nexthop()
and the (unnecessary) call to mesh_accept_plinks_update(). This will
also ensure the powersaving state code gets called in the user_mpm case.
The only cleanup tasks we need to avoid when MPM is in user-space
are sending the peering frames and stopping the plink timer, so wrap
those in the appropriate check.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
We normally return an uninitialized value, but no one checks it so it
doesn't matter. Anyway, let's silence the static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
When building a kernel with W=1, the nl80211.c file causes a number of
warnings, all about the same problem:
net/wireless/nl80211.c: In function 'nl80211_parse_mesh_config':
net/wireless/nl80211.c:5287:103: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5290:96: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5293:124: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5295:148: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5298:106: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5305:116: error: comparison is always false due to limited range of data type [-Werror=type-limits]
The problem is that gcc does not notice that the check is generate
by a macro, so it complains about comparing an unsigned type against 0.
I've tried to come up with a way to rephrase that code in a way that
avoids the warnings and otherwise improves the code as well.
This uses a set of new helper functions that perform the range checking,
and should provide slightly better type safety than the older patch,
at the expense of adding 44 lines to the code. Binary code size is
basically unchanged though (20 bytes added to 126561 bytes .text).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Registering wmediumd is currently limited to the initial network
namespace. This patch enables wmediumd to attach from non-initial
network namespaces using a user namespace having CAP_NET_ADMIN. A
registered wmediumd can forward frames on radios that have been created
in the same network namespace, even if they have been moved to other
network namespaces.
The wmediumd Netlink portid is tracked per net namespace. Additionally,
the portid is stored on all radios created in that net namespace to
simplify the portid lookup in the data path.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable bugfixes:
- Fix _cancel_empty_pagelist
- Fix a double page unlock
- Make nfs_atomic_open() call d_drop() on all ->open_context() errors.
- Fix another OPEN_DOWNGRADE bug
Other bugfixes:
- Ensure we handle delegation errors in nfs4_proc_layoutget()
- Layout stateids start out as being invalid
- Add sparse lock annotations for pnfs_find_alloc_layout
- Handle bad delegation stateids in nfs4_layoutget_handle_exception
- Fix up O_DIRECT results
- Fix potential use after free of state in nfs4_do_reclaim.
- Mark the layout stateid invalid when all segments are removed
- Don't let readdirplus revalidate an inode that was marked as stale
- Fix potential race in nfs_fhget()
- Fix an unused variable warning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IGNO
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.7-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client bugfixes from Anna Schumaker:
"Stable bugfixes:
- Fix _cancel_empty_pagelist
- Fix a double page unlock
- Make nfs_atomic_open() call d_drop() on all ->open_context() errors.
- Fix another OPEN_DOWNGRADE bug
Other bugfixes:
- Ensure we handle delegation errors in nfs4_proc_layoutget()
- Layout stateids start out as being invalid
- Add sparse lock annotations for pnfs_find_alloc_layout
- Handle bad delegation stateids in nfs4_layoutget_handle_exception
- Fix up O_DIRECT results
- Fix potential use after free of state in nfs4_do_reclaim.
- Mark the layout stateid invalid when all segments are removed
- Don't let readdirplus revalidate an inode that was marked as stale
- Fix potential race in nfs_fhget()
- Fix an unused variable warning"
* tag 'nfs-for-4.7-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Fix another OPEN_DOWNGRADE bug
make nfs_atomic_open() call d_drop() on all ->open_context() errors.
NFS: Fix an unused variable warning
NFS: Fix potential race in nfs_fhget()
NFS: Don't let readdirplus revalidate an inode that was marked as stale
NFSv4.1/pnfs: Mark the layout stateid invalid when all segments are removed
NFS: Fix a double page unlock
pnfs_nfs: fix _cancel_empty_pagelist
nfs4: Fix potential use after free of state in nfs4_do_reclaim.
NFS: Fix up O_DIRECT results
NFS/pnfs: handle bad delegation stateids in nfs4_layoutget_handle_exception
NFSv4.1/pnfs: Add sparse lock annotations for pnfs_find_alloc_layout
NFSv4.1/pnfs: Layout stateids start out as being invalid
NFSv4.1/pnfs: Ensure we handle delegation errors in nfs4_proc_layoutget()
Pull audit fixes from Paul Moore:
"Two small patches to fix audit problems in 4.7-rcX: the first fixes a
potential kref leak, the second removes some header file noise.
The first is an important bug fix that really should go in before 4.7
is released, the second is not critical, but falls into the very-nice-
to-have category so I'm including in the pull request.
Both patches are straightforward, self-contained, and pass our
testsuite without problem"
* 'stable-4.7' of git://git.infradead.org/users/pcmoore/audit:
audit: move audit_get_tty to reduce scope and kabi changes
audit: move calcs after alloc and check when logging set loginuid
Pull networking fixes from David Miller:
"I've been traveling so this accumulates more than week or so of bug
fixing. It perhaps looks a little worse than it really is.
1) Fix deadlock in ath10k driver, from Ben Greear.
2) Increase scan timeout in iwlwifi, from Luca Coelho.
3) Unbreak STP by properly reinjecting STP packets back into the
stack. Regression fix from Ido Schimmel.
4) Mediatek driver fixes (missing malloc failure checks, leaking of
scratch memory, wrong indexing when mapping TX buffers, etc.) from
John Crispin.
5) Fix endianness bug in icmpv6_err() handler, from Hannes Frederic
Sowa.
6) Fix hashing of flows in UDP in the ruseport case, from Xuemin Su.
7) Fix netlink notifications in ovs for tunnels, delete link messages
are never emitted because of how the device registry state is
handled. From Nicolas Dichtel.
8) Conntrack module leaks kmemcache on unload, from Florian Westphal.
9) Prevent endless jump loops in nft rules, from Liping Zhang and
Pablo Neira Ayuso.
10) Not early enough spinlock initialization in mlx4, from Eric
Dumazet.
11) Bind refcount leak in act_ipt, from Cong WANG.
12) Missing RCU locking in HTB scheduler, from Florian Westphal.
13) Several small MACSEC bug fixes from Sabrina Dubroca (missing RCU
barrier, using heap for SG and IV, and erroneous use of async flag
when allocating AEAD conext.)
14) RCU handling fix in TIPC, from Ying Xue.
15) Pass correct protocol down into ipv4_{update_pmtu,redirect}() in
SIT driver, from Simon Horman.
16) Socket timer deadlock fix in TIPC from Jon Paul Maloy.
17) Fix potential deadlock in team enslave, from Ido Schimmel.
18) Memory leak in KCM procfs handling, from Jiri Slaby.
19) ESN generation fix in ipv4 ESP, from Herbert Xu.
20) Fix GFP_KERNEL allocations with locks held in act_ife, from Cong
WANG.
21) Use after free in netem, from Eric Dumazet.
22) Uninitialized last assert time in multicast router code, from Tom
Goff.
23) Skip raw sockets in sock_diag destruction broadcast, from Willem
de Bruijn.
24) Fix link status reporting in thunderx, from Sunil Goutham.
25) Limit resegmentation of retransmit queue so that we do not
retransmit too large GSO frames. From Eric Dumazet.
26) Delay bpf program release after grace period, from Daniel
Borkmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (141 commits)
openvswitch: fix conntrack netlink event delivery
qed: Protect the doorbell BAR with the write barriers.
neigh: Explicitly declare RCU-bh read side critical section in neigh_xmit()
e1000e: keep VLAN interfaces functional after rxvlan off
cfg80211: fix proto in ieee80211_data_to_8023 for frames without LLC header
qlcnic: use the correct ring in qlcnic_83xx_process_rcv_ring_diag()
bpf, perf: delay release of BPF prog after grace period
net: bridge: fix vlan stats continue counter
tcp: do not send too big packets at retransmit time
ibmvnic: fix to use list_for_each_safe() when delete items
net: thunderx: Fix TL4 configuration for secondary Qsets
net: thunderx: Fix link status reporting
net/mlx5e: Reorganize ethtool statistics
net/mlx5e: Fix number of PFC counters reported to ethtool
net/mlx5e: Prevent adding the same vxlan port
net/mlx5e: Check for BlueFlame capability before allocating SQ uar
net/mlx5e: Change enum to better reflect usage
net/mlx5: Add ConnectX-5 PCIe 4.0 to list of supported devices
net/mlx5: Update command strings
net: marvell: Add separate config ANEG function for Marvell 88E1111
...
Pull s390 fixes from Martin Schwidefsky:
"Another two bug fixes for 4.7:
- The revert of patch which removed boot information for systems
using an intermediate boot kernel, e.g. the SLES12 grub setup.
- A fix for an incorrect inline assembly constraint that causes
broken code to be generated with gcc 4.8.5"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix test_fp_ctl inline assembly contraints
Revert "s390/kdump: Clear subchannel ID to signal non-CCW/SCSI IPL"
- Driver fixes for i.MX, single register, Tegra and BayTrail.
- MAINTAINERS entry for the documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e4gh
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are a bunch of fixes for pin control. Just drivers and a
MAINTAINERS fixup:
- Driver fixes for i.MX, single register, Tegra and BayTrail.
- MAINTAINERS entry for the documentation"
* tag 'pinctrl-v4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: baytrail: Fix mingled clock pins
MAINTAINERS: belong Documentation/pinctrl.txt properly
pinctrl: tegra: Fix build dependency
gpio: tegra: Make lockdep class file-scoped
pinctrl: single: Fix missing flush of posted write for a wakeirq
pinctrl: imx: Do not treat a PIN without MUX register as an error
Pull cgroup fixes from Tejun Heo:
"Three fix patches. Two are for cgroup / css init failure path. The
last one makes css_set_lock irq-safe as the deadline scheduler ends up
calling put_css_set() from irq context"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Disable IRQs while holding css_set_lock
cgroup: set css->id to -1 during init
cgroup: remove redundant cleanup in css_create
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
-----BEGIN PGP SIGNATURE-----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=dAbs
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-06-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two small fixes
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-06-27
This series contains updates to i40e and i40evf only.
Mitch provides several changes, first adds functions to enable and disable
VSI on a VEB, which allows for configuration of limited promiscuous mode
specifically for bridging purposes. Sets the RSS Hash Enable registers by
default now that VF RSS is configured by the PF driver. Fixed a issue
where we could overflow the buffer, by checking the address count and bail
out of the loop at the appropriate time. Removed the need for a reset
when the device enters limited promiscuous mode, since this was causing
heartburn for people who were using VFs and bridging.
Catherine adds a call to set the client interface down when we put the VSI
down. Fixed an issue where RSS queues was being limited to the number
of CPUs, so if a user wants to use more queues than CPUs, we want to
trust they know what they are doing and let them.
Greg cleans up the driver suspend routine to ensure we are calling
synchronize_irq() before freeing IRQ vectors and explicitly free the other
causes interrupt resources and shut down the MSIX interrupt.
Serey fixes i40e_set_settings() to not fail when a Direct Attach (DA)
cable is used.
Avinash fixes a supported link bug by removing code which was not allowing
100BaseT to show up in the supported link modes for 10GBaseT PHYs.
Shannon adds a bit of information to the error messages to help determine
the source of error by adding VSI info to macaddr messages.
Tushar Dave fixes error received when turning off TSO on some systems,
which was caused by enabling FD_SB without checking availability of
MSIx vectors, so add the check.
Neerav fixes a possible panic when LLDP/DCBX change happens and the
driver tried to notify the client(s) for each of the PF VSIs, which would
panic when it reached a VSI that did not have any netdev associated with
it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first and last netlink message for a particular conntrack are
actually sent. The first message is sent through nf_conntrack_confirm when
the conntrack is committed. The last one is sent when the conntrack is
destroyed on timeout. The other conntrack state change messages are not
advertised.
When the conntrack subsystem is used from netfilter, nf_conntrack_confirm
is called for each packet, from the postrouting hook, which in turn calls
nf_ct_deliver_cached_events to send the state change netlink messages.
This commit fixes the problem by calling nf_ct_deliver_cached_events in the
non-commit case as well.
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
CC: Joe Stringer <joestringer@nicira.com>
CC: Justin Pettit <jpettit@nicira.com>
CC: Andy Zhou <azhou@nicira.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPQ doorbell is currently protected with the compilation barrier. Under the
stress scenarios, we may get into a state where (due to the weak ordering)
several ramrod doorbells were written to the BAR with an out-of-order
producer values. Need to change the barrier type to a write barrier to make
sure that the write buffer is flushed after each doorbell.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_unshare() fails, we call qdisc_drop() with a NULL skb, which
is no longer supported.
Fixes: 520ac30f45 ("net_sched: drop packets after root qdisc lock is released")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.
More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.
When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.
This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.
Fixes: 4fd3d7d9e8 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed*: Fix the static checker warnings.
The patch series addresses the static checker warnings introduced by the
earlier patches related to qed/qede coalesce configuration support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checker warnings:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:435 qede_get_coalesce()
warn: passing casted pointer '&coal->rx_coalesce_usecs' to
'edev->ops->common->get_coalesce()' 32 vs 16.
The u32 pointer is being typecasted to u16 which may fail for big-endian
platforms.
Fixes: d552fa84cb ("qede: Add support for coalescing config read/update.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've got a bug report about an e1000e interface, where a VLAN interface is
set up on top of it:
$ ip link add link ens1f0 name ens1f0.99 type vlan id 99
$ ip link set ens1f0 up
$ ip link set ens1f0.99 up
$ ip addr add 192.168.99.92 dev ens1f0.99
At this point, I can ping another host on vlan 99, ip 192.168.99.91.
However, if I do the following:
$ ethtool -K ens1f0 rxvlan off
Then no traffic passes on ens1f0.99. It comes back if I toggle rxvlan on
again. I'm not sure if this is actually intended behavior, or if there's a
lack of software VLAN stripping fallback, or what, but things continue to
work if I simply don't call e1000e_vlan_strip_disable() if there are
active VLANs (plagiarizing a function from the e1000 driver here) on the
interface.
Also slipped a related-ish fix to the kerneldoc text for
e1000e_vlan_strip_disable here...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes: 2d1c304cb2 ("cfg80211: add function for 802.3 conversion with separate output buffer")
Cc: stable@vger.kernel.org
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There is a static checker warning here "warn: mask and shift to zero"
and the code sets "ring" to zero every time. From looking at how
QLCNIC_FETCH_RING_ID() is used in qlcnic_83xx_process_rcv_ring() the
qlcnic_83xx_hndl() should be removed.
Fixes: 4be41e92f7 ('qlcnic: 83xx data path routines')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dead9f29dd ("perf: Fix race in BPF program unregister") moved
destruction of BPF program from free_event_rcu() callback to __free_event(),
which is problematic if used with tail calls: if prog A is attached as
trace event directly, but at the same time present in a tail call map used
by another trace event program elsewhere, then we need to delay destruction
via RCU grace period since it can still be in use by the program doing the
tail call (the prog first needs to be dropped from the tail call map, then
trace event with prog A attached destroyed, so we get immediate destruction).
Fixes: dead9f29dd ("perf: Fix race in BPF program unregister")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Jann Horn <jann@thejh.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made a dumb off-by-one mistake when I added the vlan stats counter
dumping code. The increment should happen before the check, not after
otherwise we miss one entry when we continue dumping.
Fixes: a60c090361 ("bridge: netlink: export per-vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun reported a bug in TCP stack and bisected it to a recent commit.
In case where we process SACK, we can coalesce multiple skbs
into fat ones (tcp_shift_skb_data()), to lower write queue
overhead, because we do not expect to retransmit these packets.
However, SACK reneging can happen, forcing the sender to retransmit
all these packets. If skb->len is above 64KB, we then send buggy
IP packets that could hang TSO engine on cxgb4.
Neal suggested to use tcp_tso_autosize() instead of tp->gso_segs
so that we cook packets of optimal size vs TCP/pacing.
Thanks to Arjun for reporting the bug and running the tests !
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Arjun V <arjun@chelsio.com>
Tested-by: Arjun V <arjun@chelsio.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each() macro aptly named
list_for_each_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Context implies that port in struct "udp_media_addr" is referring
to a UDP port.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP msg2addr function tipc_udp_msg2addr() can return -EINVAL which
prior to this patch was unhanded in the caller.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing before the open parenthesis '(', and this
will introduce much more noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham says:
====================
net: thunderx: Miscellaneous fixes
This 2 patch series fixes issues w.r.t physical link status
reporting and transmit datapath configuration for
secondary qsets.
Changes from v1:
Fixed lmac disable sequence for interfaces of type SGMII.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TL4 calculation for a given SQ of secondary Qsets is incorrect
and goes out of bounds and also for some SQ's TL4 chosen will
transmit data via a different BGX interface and not same as
primary Qset's interface.
This patch fixes this issue.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for SMU RX local/remote faults along with SPU LINK
status. Otherwise at times link is UP at our end but DOWN
at link partner's side. Also due to an issue in BGX it's
rarely seen that initialization doesn't happen properly
and SMU RX reports faults with everything fine at SPU.
This patch tries to reinitialize LMAC to fix it.
Also fixed LMAC disable sequence to properly bring down link.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Tao Wang <tao.wang@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations, gcc produces a warning for correct code
in this driver:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:107:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read48':
drivers/net/dsa/b53/b53_mmap.c:91:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
^~~~~~~
drivers/net/dsa/b53/b53_mmap.c:83:11: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 16) | lo;
I have seen the warning before and at the time thought I had fixed
it with 55e7f6abe1 ("dsa: b53: fix big-endian register access"),
however it now came back in a different randconfig build that happens
to have different inlining decisions in the compiler.
The mistake that gcc makes here is that it thinks the second call to
readl() might fail because the address 'reg + 4' is not a multiple
of four despite having knowing that 'reg' itself is a multiple of four.
By open-coding the two reads without the redundant alignment check,
we can avoid the warning and produce slightly better object code, but
get slightly longer source code instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes#2 for 4.7-rc
The following series provides one-liners fixes for mlx5 driver plus one
medium patch to reorganize ethtool counters reporting.
Highlights:
- Added MODIFY_FLOW_TABLE to command strings table
- Add ConnectX-5 PCIe 4.0 to list of supported devices
- Rename ASYNC_EVENTS enum
- Enable BlueFlame only when supported by device
- Avoid adding same vxlan port twice
- Report the correct number of PFC counters
- Reorganize ethtool reported counters and remove duplications
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Categorize and reorganize ethtool statistics counters by renaming to
"rx_*" and "tx_*" and removing redundant and duplicated counters, this
way they are easier to grasp and more user friendly.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of PFC counters used to count only number of priorities with PFC
enabled, but each priority has more than one counter, hence the need to
multiply it by the number of PFC counters per priority.
Fixes: cf678570d5 ('net/mlx5e: Add per priority group to PPort counters')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
