Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Don't inflate the kernel size with data that isn't used. The conditional
declaration also fixes the following warning when building with clang:
drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match'
is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add missing hooks in the LTC2497 IIO driver to allow hwmon mapping.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The array stm32h7_adc_ckmodes_spec does not need to be in global scope, so
make it static.
Cleans up sparse warning:
"symbol 'stm32h7_adc_ckmodes_spec' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some part of the configuration are not touched after the probe
and if something goes wrong on writing the initial one,
the chip will misbehave.
Adding an error checking ensures that the inital configuration will
be written correctly. Moreover ensures that a sensible configuration
will be saved in driver data and used subsequently as intended.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial channel should be the first available channel on
all configurations, so changing to channel 0 available on
all supported chips.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Open drain should work fine with rising or high level IRQs,
this code was due to some misunderstanding on my part.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a link to the TCS3472 datasheet in the AMS's website.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch supports auxadc suspend/resume flow.
Disable auxadc clk and power in suspend function.
Enable axuadc clk and power in resume function.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The commit adds mt7622 compatible node in binding document.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add open drain support in order to share requested IRQ line between
st_lsm6dsx device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree bindings for Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree bindings for Measurement-Specialties HTU21 temperature & humidity sensor and humidity part of MS8607 sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table for Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Clock name has been updated during driver/DT binding review:
https://lkml.org/lkml/2016/12/13/718
Update DT binding doc to reflect this.
Fixes: bf2d8581b1 (iio: Add bindings for STM32 timer trigger driver)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for suspend/resume functionality for the ADC IP
in sama5d2 SoC.
In order to enter Suspend to ram mode (backup + self refresh mode for
memory), in which the ADC IP is no longer powered, we need to reset the
pins to default state, for the scenario when they are also used for I2C
bus to communicate with the PMIC.
On resume, we need to reconfigure the ADC IP registers and reconfigure the
trigger registers in the case when the suspend procedure is done while
sysfs has the buffer and trigger enabled.
In the case the suspend happens exactly during a software triggered
conversion, the request will time out, because we reset and power down
the ADC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In order to add proper device tree support give a more general name
to of_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable multiread by default for LIS3MDL since using I2C interface
the subaddr Msb is used to automatically increase the slave address
during multiple data read/write. In the same way, using SPI interface,
bit 1 in register address is used to enable auto-increment of the slave
address in multiple read/write.
Fixes: 872e79add7 (iio:magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The integration time is controlled by the ATIME register only. However,
this register is written by i2c_smbus_write_word_data() in write_raw().
We actually don't need to write a subsequent register. So just use
i2c_smbus_write_byte_data() instead.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While the INA226 has a conversion ready flag (CVRF) in the R/W Mask/Enable
register with read-to-clear semantics, the corresponding bit of the INA219
(CNVR) is part of the bus voltage register. The flag is cleared by reading
the power register.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree bindings for Measurement Specialties TSYS01 temperature sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for the external hardware trigger on pin ADTRG,
integrated the three possible edges into the driver
and created buffer management for data retrieval
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add property for the edge type of the hardware trigger pin ADTRG
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
To keep IMX7D_ADC text consistent with other iio/adc entries, add
the vendor name to the driver menu text.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table and point it to a list of compatible device tree
device id's.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Include datasheet links, add i2c_device_id entries, and update
kconfig help for compatible HDC10xx devices: HDC1000, HDC1008,
HDC1010, HDC1050, and HDC1080.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the bindings for the family of HDC100x sensors.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add proper support for L3GD20H gyroscope sensor. In particular:
- use L3GD20H as device name instead of L3GD20
- fix available full scales
- fix available sample frequencies
Note that the original patch listed first below introduced broken support for
this part. The second patch drops the support as it didn't work.
This new patch brings in working support.
Fixes: 9444a300c2 (IIO: Add support for L3GD20H gyroscope)
Fixes: a065771641 ("iio:gyro: bug on L3GD20H gyroscope support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the BOSC0200 ACPI device id used on some x86 tablets.
note driver_data is not set to a specific model, driver_data is not
used anyways (instead detection is done on the chip_id reg) and the
2 tablets with a BOSC0200 ACPI device id I've have 2 different chips,
one has a BMA250E, the other a BMA222E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the following checkpatch.pl warning:
WARNING: Prefer kmalloc_array over kmalloc with multiply
Signed-off-by: Denis Petrovic <denis.petrovic@edu.ece.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces several instances where a pointer is compared to NULL
(i.e., `ptr == NULL`) with `!ptr`, which is preferred.
Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dprc.h is only used in the mc bus driver so move it together with the
sources thus making it private.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mc-cmd.h contains some low level functions used to encode and decode
commands to the MC. They are used by the drivers so move them to the
public headers and get rid of the mc-cmd.h header.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mc-sys.h contains the API to send commands to the MC and is used
by drivers. Move it to the public headers and get rid of the mc-sys.h
header.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Few files using byte order macros but did not explicitly
included the required kernel header, so add it.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dpmng.h & dpmng.c files expose an API of just one function which is only
used by the bus driver. Move that single API in the bus source as static
and remove the two files.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the mc-bus.h contents is only used privately in the bus driver so
move everything to the private header and get rid of the mc-bus.h
header file.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define dev_is_fsl_mc() and the bus type definition (fsl_mc_bus_type)
are used externally so move them to the public header.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_mc_msi_create_irq_domain() will is used from the irqchip glue code
so it needs to be in the public headers.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are never used outside the source they are implemented in and very
likely never will, so it's safe to make them static.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
