This adds code to enable the HPT resizing code to work on POWER9,
which uses a slightly modified HPT entry format compared to POWER8.
On POWER9, we convert HPTEs read from the HPT from the new format to
the old format so that the rest of the HPT resizing code can work as
before. HPTEs written to the new HPT are converted to the new format
as the last step before writing them into the new HPT.
This takes out the checks added by commit bcd3bb63db ("KVM: PPC:
Book3S HV: Disable HPT resizing on POWER9 for now", 2017-02-18),
now that HPT resizing works on POWER9.
On POWER9, when we pivot to the new HPT, we now call
kvmppc_setup_partition_table() to update the partition table in order
to make the hardware use the new HPT.
[paulus@ozlabs.org - added kvmppc_setup_partition_table() call,
wrote commit message.]
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch of the powerpc tree to get
two patches which are prerequisites for the following patch series,
plus another patch which touches both powerpc and KVM code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a register identifier for use with the one_reg interface
to allow the decrementer expiry time to be read and written by
userspace. The decrementer expiry time is in guest timebase units
and is equal to the sum of the decrementer and the guest timebase.
(The expiry time is used rather than the decrementer value itself
because the expiry time is not constantly changing, though the
decrementer value is, while the guest vcpu is not running.)
Without this, a guest vcpu migrated to a new host will see its
decrementer set to some random value. On POWER8 and earlier, the
decrementer is 32 bits wide and counts down at 512MHz, so the
guest vcpu will potentially see no decrementer interrupts for up
to about 4 seconds, which will lead to a stall. With POWER9, the
decrementer is now 56 bits side, so the stall can be much longer
(up to 2.23 years) and more noticeable.
To help work around the problem in cases where userspace has not been
updated to migrate the decrementer expiry time, we now set the
default decrementer expiry at vcpu creation time to the current time
rather than the maximum possible value. This should mean an
immediate decrementer interrupt when a migrated vcpu starts
running. In cases where the decrementer is 32 bits wide and more
than 4 seconds elapse between the creation of the vcpu and when it
first runs, the decrementer would have wrapped around to positive
values and there may still be a stall - but this is no worse than
the current situation. In the large-decrementer case, we are sure
to get an immediate decrementer interrupt (assuming the time from
vcpu creation to first run is less than 2.23 years) and we thus
avoid a very long stall.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
KVM API says for the signal mask you set via KVM_SET_SIGNAL_MASK, that
"any unblocked signal received [...] will cause KVM_RUN to return with
-EINTR" and that "the signal will only be delivered if not blocked by
the original signal mask".
This, however, is only true, when the calling task has a signal handler
registered for a signal. If not, signal evaluation is short-circuited for
SIG_IGN and SIG_DFL, and the signal is either ignored without KVM_RUN
returning or the whole process is terminated.
Make KVM_SET_SIGNAL_MASK behave as advertised by utilizing logic similar
to that in do_sigtimedwait() to avoid short-circuiting of signals.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In an excess of caution, commit 6f63e81bda ("KVM: PPC: Book3S: Add
MMIO emulation for FP and VSX instructions", 2017-02-21) included
checks for the case that vcpu->arch.mmio_vsx_copy_nums is less than
zero, even though its type is u8. This causes a Coverity warning,
so we remove the check for < 0. We also adjust the associated
comment to be more accurate ("4 or less" rather than "less than 4").
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in a couple of fixes from the kvm-ppc-fixes branch that
modify the same areas of code as some commits from the kvm-ppc-next
branch, in order to resolve the conflicts.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This sets up the machinery for switching a guest between HPT (hashed
page table) and radix MMU modes, so that in future we can run a HPT
guest on a radix host on POWER9 machines.
* The KVM_PPC_CONFIGURE_V3_MMU ioctl can now specify either HPT or
radix mode, on a radix host.
* The KVM_CAP_PPC_MMU_HASH_V3 capability now returns 1 on POWER9
with HV KVM on a radix host.
* The KVM_PPC_GET_SMMU_INFO returns information about the HPT MMU on a
radix host.
* The KVM_PPC_ALLOCATE_HTAB ioctl on a radix host will switch the
guest to HPT mode and allocate a HPT.
* For simplicity, we now allocate the rmap array for each memslot,
even on a radix host, since it will be needed if the guest switches
to HPT mode.
* Since we cannot yet run a HPT guest on a radix host, the KVM_RUN
ioctl will return an EINVAL error in that case.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently we use CPU_FTR_TM to decide if the CPU/kernel can support
TM (Transactional Memory), and if it's true we advertise that to
Qemu (or similar) via KVM_CAP_PPC_HTM.
PPC_FEATURE2_HTM is the user-visible feature bit, which indicates that
the CPU and kernel can support TM. Currently CPU_FTR_TM and
PPC_FEATURE2_HTM always have the same value, either true or false, so
using the former for KVM_CAP_PPC_HTM is correct.
However some Power9 CPUs can operate in a mode where TM is enabled but
TM suspended state is disabled. In this mode CPU_FTR_TM is true, but
PPC_FEATURE2_HTM is false. Instead a different PPC_FEATURE2 bit is
set, to indicate that this different mode of TM is available.
It is not safe to let guests use TM as-is, when the CPU is in this
mode. So to prevent that from happening, use PPC_FEATURE2_HTM to
determine the value of KVM_CAP_PPC_HTM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The following program causes a kernel oops:
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <sys/ioctl.h>
#include <linux/kvm.h>
main()
{
int fd = open("/dev/kvm", O_RDWR);
ioctl(fd, KVM_CHECK_EXTENSION, KVM_CAP_PPC_HTM);
}
This happens because when using the global KVM fd with
KVM_CHECK_EXTENSION, kvm_vm_ioctl_check_extension() gets
called with a NULL kvm argument, which gets dereferenced
in is_kvmppc_hv_enabled(). Spotted while reading the code.
Let's use the hv_enabled fallback variable, like everywhere
else in this function.
Fixes: 23528bb21e ("KVM: PPC: Introduce KVM_CAP_PPC_HTM")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).
But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.
This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts
pending.
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=6hNK
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.13
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
Conflicts:
arch/s390/include/asm/kvm_host.h
Now that userspace can set the virtual SMT mode by enabling the
KVM_CAP_PPC_SMT capability, it is useful for userspace to be able
to query the set of possible virtual SMT modes. This provides a
new capability, KVM_CAP_PPC_SMT_POSSIBLE, to provide this
information. The return value is a bitmap of possible modes, with
bit N set if virtual SMT mode 2^N is available. That is, 1 indicates
SMT1 is available, 2 indicates that SMT2 is available, 3 indicates
that both SMT1 and SMT2 are available, and so on.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This introduces a new KVM capability to control how KVM behaves
on machine check exception (MCE) in HV KVM guests.
If this capability has not been enabled, KVM redirects machine check
exceptions to guest's 0x200 vector, if the address in error belongs to
the guest. With this capability enabled, KVM will cause a guest exit
with the exit reason indicating an NMI.
The new capability is required to avoid problems if a new kernel/KVM
is used with an old QEMU, running a guest that doesn't issue
"ibm,nmi-register". As old QEMU does not understand the NMI exit
type, it treats it as a fatal error. However, the guest could have
handled the machine check error if the exception was delivered to
guest's 0x200 interrupt vector instead of NMI exit in case of old
QEMU.
[paulus@ozlabs.org - Reworded the commit message to be clearer,
enable only on HV KVM.]
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On POWER9, we no longer have the restriction that we had on POWER8
where all threads in a core have to be in the same partition, so
the CPU threads are now independent. However, we still want to be
able to run guests with a virtual SMT topology, if only to allow
migration of guests from POWER8 systems to POWER9.
A guest that has a virtual SMT mode greater than 1 will expect to
be able to use the doorbell facility; it will expect the msgsndp
and msgclrp instructions to work appropriately and to be able to read
sensible values from the TIR (thread identification register) and
DPDES (directed privileged doorbell exception status) special-purpose
registers. However, since each CPU thread is a separate sub-processor
in POWER9, these instructions and registers can only be used within
a single CPU thread.
In order for these instructions to appear to act correctly according
to the guest's virtual SMT mode, we have to trap and emulate them.
We cause them to trap by clearing the HFSCR_MSGP bit in the HFSCR
register. The emulation is triggered by the hypervisor facility
unavailable interrupt that occurs when the guest uses them.
To cause a doorbell interrupt to occur within the guest, we set the
DPDES register to 1. If the guest has interrupts enabled, the CPU
will generate a doorbell interrupt and clear the DPDES register in
hardware. The DPDES hardware register for the guest is saved in the
vcpu->arch.vcore->dpdes field. Since this gets written by the guest
exit code, other VCPUs wishing to cause a doorbell interrupt don't
write that field directly, but instead set a vcpu->arch.doorbell_request
flag. This is consumed and set to 0 by the guest entry code, which
then sets DPDES to 1.
Emulating reads of the DPDES register is somewhat involved, because
it requires reading the doorbell pending interrupt status of all of the
VCPU threads in the virtual core, and if any of those VCPUs are
running, their doorbell status is only up-to-date in the hardware
DPDES registers of the CPUs where they are running. In order to get
a reasonable approximation of the current doorbell status, we send
those CPUs an IPI, causing an exit from the guest which will update
the vcpu->arch.vcore->dpdes field. We then use that value in
constructing the emulated DPDES register value.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This allows userspace to set the desired virtual SMT (simultaneous
multithreading) mode for a VM, that is, the number of VCPUs that
get assigned to each virtual core. Previously, the virtual SMT mode
was fixed to the number of threads per subcore, and if userspace
wanted to have fewer vcpus per vcore, then it would achieve that by
using a sparse CPU numbering. This had the disadvantage that the
vcpu numbers can get quite large, particularly for SMT1 guests on
a POWER8 with 8 threads per core. With this patch, userspace can
set its desired virtual SMT mode and then use contiguous vcpu
numbering.
On POWER8, where the threading mode is "strict", the virtual SMT mode
must be less than or equal to the number of threads per subcore. On
POWER9, which implements a "loose" threading mode, the virtual SMT
mode can be any power of 2 between 1 and 8, even though there is
effectively one thread per subcore, since the threads are independent
and can all be in different partitions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A first step in vcpu->requests encapsulation. Additionally, we now
use READ_ONCE() when accessing vcpu->requests, which ensures we
always load vcpu->requests when it's accessed. This is important as
other threads can change it any time. Also, READ_ONCE() documents
that vcpu->requests is used with other threads, likely requiring
memory barriers, which it does.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[ Documented the new use of READ_ONCE() and converted another check
in arch/mips/kvm/vz.c ]
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Commit e91aa8e6ec ("KVM: PPC: Enable IOMMU_API for KVM_BOOK3S_64
permanently", 2017-03-22) enabled the SPAPR TCE code for all 64-bit
Book 3S kernel configurations in order to simplify the code and
reduce #ifdefs. However, 64-bit Book 3S PPC platforms other than
pseries and powernv don't implement the necessary IOMMU callbacks,
leading to build failures like the following (for a pasemi config):
scripts/kconfig/conf --silentoldconfig Kconfig
warning: (KVM_BOOK3S_64) selects SPAPR_TCE_IOMMU which has unmet direct dependencies (IOMMU_SUPPORT && (PPC_POWERNV || PPC_PSERIES))
...
CC [M] arch/powerpc/kvm/book3s_64_vio.o
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_64_vio.c: In function ‘kvmppc_clear_tce’:
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_64_vio.c:363:2: error: implicit declaration of function ‘iommu_tce_xchg’ [-Werror=implicit-function-declaration]
iommu_tce_xchg(tbl, entry, &hpa, &dir);
^
To fix this, we make the inclusion of the SPAPR TCE support, and the
code that uses it in book3s_vio.c and book3s_vio_hv.c, depend on
the inclusion of support for the pseries and/or powernv platforms.
This means that when running a 'pseries' guest on those platforms,
the guest won't have in-kernel acceleration of the PAPR TCE hypercalls,
but at least now they compile.
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The main thing here is a new implementation of the in-kernel
XICS interrupt controller emulation for POWER9 machines, from Ben
Herrenschmidt.
POWER9 has a new interrupt controller called XIVE (eXternal Interrupt
Virtualization Engine) which is able to deliver interrupts directly
to guest virtual CPUs in hardware without hypervisor intervention.
With this new code, the guest still sees the old XICS interface but
performance is better because the XICS emulation in the host uses the
XIVE directly rather than going through a XICS emulation in firmware.
Conflicts:
arch/powerpc/kernel/cpu_setup_power.S [cherry-picked fix]
arch/powerpc/kvm/book3s_xive.c [include asm/debugfs.h]
This merges in the powerpc topic/xive branch to bring in the code for
the in-kernel XICS interrupt controller emulation to use the new XIVE
(eXternal Interrupt Virtualization Engine) hardware in the POWER9 chip
directly, rather than via a XICS emulation in firmware.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Users were expected to use kvm_check_request() for testing and clearing,
but request have expanded their use since then and some users want to
only test or do a faster clear.
Make sure that requests are not directly accessed with bit operations.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.
This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT
and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO
without passing them to user space which saves time on switching
to user space and back.
This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM.
KVM tries to handle a TCE request in the real mode, if failed
it passes the request to the virtual mode to complete the operation.
If it a virtual mode handler fails, the request is passed to
the user space; this is not expected to happen though.
To avoid dealing with page use counters (which is tricky in real mode),
this only accelerates SPAPR TCE IOMMU v2 clients which are required
to pre-register the userspace memory. The very first TCE request will
be handled in the VFIO SPAPR TCE driver anyway as the userspace view
of the TCE table (iommu_table::it_userspace) is not allocated till
the very first mapping happens and we cannot call vmalloc in real mode.
If we fail to update a hardware IOMMU table unexpected reason, we just
clear it and move on as there is nothing really we can do about it -
for example, if we hot plug a VFIO device to a guest, existing TCE tables
will be mirrored automatically to the hardware and there is no interface
to report to the guest about possible failures.
This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to
the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd
and associates a physical IOMMU table with the SPAPR TCE table (which
is a guest view of the hardware IOMMU table). The iommu_table object
is cached and referenced so we do not have to look up for it in real mode.
This does not implement the UNSET counterpart as there is no use for it -
once the acceleration is enabled, the existing userspace won't
disable it unless a VFIO container is destroyed; this adds necessary
cleanup to the KVM_DEV_VFIO_GROUP_DEL handler.
This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user
space.
This adds real mode version of WARN_ON_ONCE() as the generic version
causes problems with rcu_sched. Since we testing what vmalloc_to_phys()
returns in the code, this also adds a check for already existing
vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect().
This finally makes use of vfio_external_user_iommu_id() which was
introduced quite some time ago and was considered for removal.
Tests show that this patch increases transmission speed from 220MB/s
to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch provides the MMIO load/store emulation for instructions
of 'double & vector unsigned char & vector signed char & vector
unsigned short & vector signed short & vector unsigned int & vector
signed int & vector double '.
The instructions that this adds emulation for are:
- ldx, ldux, lwax,
- lfs, lfsx, lfsu, lfsux, lfd, lfdx, lfdu, lfdux,
- stfs, stfsx, stfsu, stfsux, stfd, stfdx, stfdu, stfdux, stfiwx,
- lxsdx, lxsspx, lxsiwax, lxsiwzx, lxvd2x, lxvw4x, lxvdsx,
- stxsdx, stxsspx, stxsiwx, stxvd2x, stxvw4x
[paulus@ozlabs.org - some cleanups, fixes and rework, make it
compile for Book E, fix build when PR KVM is built in]
Signed-off-by: Bin Lu <lblulb@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Remove code from architecture files that can be moved to virt/kvm, since there
is already common code for coalesced MMIO.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[Removed a pointless 'break' after 'return'.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Paul Mackerras writes:
"Please do a pull from my kvm-ppc-next branch to get some fixes which I
would like to have in 4.11. There are four small commits there; two
are fixes for potential host crashes in the new HPT resizing code, and
the other two are changes to printks to make KVM on PPC a little less
noisy."
The new HPT resizing code added in commit b5baa68773 ("KVM: PPC:
Book3S HV: KVM-HV HPT resizing implementation", 2016-12-20) doesn't
have code to handle the new HPTE format which POWER9 uses. Thus it
would be best not to advertise it to userspace on POWER9 systems
until it works properly.
Also, since resize_hpt_rehash_hpte() contains BUG_ON() calls that
could be hit on POWER9, let's prevent it from being called on POWER9
for now.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The purpose of the KVM_SET_SIGNAL_MASK API is to let userspace "kick"
a VCPU out of KVM_RUN through a POSIX signal. A signal is attached
to a dummy signal handler; by blocking the signal outside KVM_RUN and
unblocking it inside, this possible race is closed:
VCPU thread service thread
--------------------------------------------------------------
check flag
set flag
raise signal
(signal handler does nothing)
KVM_RUN
However, one issue with KVM_SET_SIGNAL_MASK is that it has to take
tsk->sighand->siglock on every KVM_RUN. This lock is often on a
remote NUMA node, because it is on the node of a thread's creator.
Taking this lock can be very expensive if there are many userspace
exits (as is the case for SMP Windows VMs without Hyper-V reference
time counter).
As an alternative, we can put the flag directly in kvm_run so that
KVM can see it:
VCPU thread service thread
--------------------------------------------------------------
raise signal
signal handler
set run->immediate_exit
KVM_RUN
check run->immediate_exit
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This updates the KVM_CAP_SPAPR_RESIZE_HPT capability to advertise the
presence of in-kernel HPT resizing on KVM HV.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a few last pieces of the support for radix guests:
* Implement the backends for the KVM_PPC_CONFIGURE_V3_MMU and
KVM_PPC_GET_RMMU_INFO ioctls for radix guests
* On POWER9, allow secondary threads to be on/off-lined while guests
are running.
* Set up LPCR and the partition table entry for radix guests.
* Don't allocate the rmap array in the kvm_memory_slot structure
on radix.
* Don't try to initialize the HPT for radix guests, since they don't
have an HPT.
* Take out the code that prevents the HV KVM module from
initializing on radix hosts.
At this stage, we only support radix guests if the host is running
in radix mode, and only support HPT guests if the host is running in
HPT mode. Thus a guest cannot switch from one mode to the other,
which enables some simplifications.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds the implementation of the KVM_PPC_CONFIGURE_V3_MMU ioctl
for HPT guests on POWER9. With this, we can return 1 for the
KVM_CAP_PPC_MMU_HASH_V3 capability.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds two capabilities and two ioctls to allow userspace to
find out about and configure the POWER9 MMU in a guest. The two
capabilities tell userspace whether KVM can support a guest using
the radix MMU, or using the hashed page table (HPT) MMU with a
process table and segment tables. (Note that the MMUs in the
POWER9 processor cores do not use the process and segment tables
when in HPT mode, but the nest MMU does).
The KVM_PPC_CONFIGURE_V3_MMU ioctl allows userspace to specify
whether a guest will use the radix MMU or the HPT MMU, and to
specify the size and location (in guest space) of the process
table.
The KVM_PPC_GET_RMMU_INFO ioctl gives userspace information about
the radix MMU. It returns a list of supported radix tree geometries
(base page size and number of bits indexed at each level of the
radix tree) and the encoding used to specify the various page
sizes for the TLB invalidate entry instruction.
Initially, both capabilities return 0 and the ioctls return -EINVAL,
until the necessary infrastructure for them to operate correctly
is added.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At present KVM on powerpc always reports KVM_CAP_PPC_ALLOC_HTAB as enabled.
However, the ioctl() it advertises (KVM_PPC_ALLOCATE_HTAB) only actually
works on KVM HV. On KVM PR it will fail with ENOTTY.
QEMU already has a workaround for this, so it's not breaking things in
practice, but it would be better to advertise this correctly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With POWER9, each CPU thread has its own MMU context and can be
in the host or a guest independently of the other threads; there is
still however a restriction that all threads must use the same type
of address translation, either radix tree or hashed page table (HPT).
Since we only support HPT guests on a HPT host at this point, we
can treat the threads as being independent, and avoid all of the
work of coordinating the CPU threads. To make this simpler, we
introduce a new threads_per_vcore() function that returns 1 on
POWER9 and threads_per_subcore on POWER7/8, and use that instead
of threads_per_subcore or threads_per_core in various places.
This also changes the value of the KVM_CAP_PPC_SMT capability on
POWER9 systems from 4 to 1, so that userspace will not try to
create VMs with multiple vcpus per vcore. (If userspace did create
a VM that thought it was in an SMT mode, the VM might try to use
the msgsndp instruction, which will not work as expected. In
future it may be possible to trap and emulate msgsndp in order to
allow VMs to think they are in an SMT mode, if only for the purpose
of allowing migration from POWER8 systems.)
With all this, we can now run guests on POWER9 as long as the host
is running with HPT translation. Since userspace currently has no
way to request radix tree translation for the guest, the guest has
no choice but to use HPT translation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Two stubs are added:
o kvm_arch_has_vcpu_debugfs(): must return true if the arch
supports creating debugfs entries in the vcpu debugfs dir
(which will be implemented by the next commit)
o kvm_arch_create_vcpu_debugfs(): code that creates debugfs
entries in the vcpu debugfs dir
For x86, this commit introduces a new file to avoid growing
arch/x86/kvm/x86.c even more.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Select IRQ_BYPASS_MANAGER for PPC when CONFIG_KVM is set.
Add the PPC producer functions for add and del producer.
[paulus@ozlabs.org - Moved new functions from book3s.c to powerpc.c
so booke compiles; added kvm_arch_has_irq_bypass implementation.]
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It doesn't make sense to create irqfds for a VM that doesn't have
in-kernel interrupt controller emulation. There is an existing
interface for architecture code to tell the irqfd code whether or
not any interrupt controller has been initialized, called
kvm_arch_intc_initialized(), so let's implement that for powerpc.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Introduce a new KVM capability, KVM_CAP_PPC_HTM, that can be queried to
determine if a PowerPC KVM guest should use HTM (Hardware Transactional
Memory).
This will be used by QEMU to populate the pa-features bits in the
guest's device tree.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the functions from context_tracking.h directly.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the guest does a sign-extending load instruction (such as lha
or lwa) to an emulated MMIO location, it results in a call to
kvmppc_handle_loads() in the host. That function sets the
vcpu->arch.mmio_sign_extend flag and calls kvmppc_handle_load()
to do the rest of the work. However, kvmppc_handle_load() sets
the mmio_sign_extend flag to 0 unconditionally, so the sign
extension never gets done.
To fix this, we rename kvmppc_handle_load to __kvmppc_handle_load
and add an explicit parameter to indicate whether sign extension
is required. kvmppc_handle_load() and kvmppc_handle_loads() then
become 1-line functions that just call __kvmppc_handle_load()
with the extra parameter.
Reported-by: Bin Lu <lblulb@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The barrier also orders the write to mode from any reads
to the page tables done and so update the comment.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The existing KVM_CREATE_SPAPR_TCE only supports 32bit windows which is not
enough for directly mapped windows as the guest can get more than 4GB.
This adds KVM_CREATE_SPAPR_TCE_64 ioctl and advertises it
via KVM_CAP_SPAPR_TCE_64 capability. The table size is checked against
the locked memory limit.
Since 64bit windows are to support Dynamic DMA windows (DDW), let's add
@bus_offset and @page_shift which are also required by DDW.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support to real-mode KVM to search for a core
running in the host partition and send it an IPI message with
VCPU to be woken. This avoids having to switch to the host
partition to complete an H_IPI hypercall when the VCPU which
is the target of the the H_IPI is not loaded (is not running
in the guest).
The patch also includes the support in the IPI handler running
in the host to do the wakeup by calling kvmppc_xics_ipi_action
for the PPC_MSG_RM_HOST_ACTION message.
When a guest is being destroyed, we need to ensure that there
are no pending IPIs waiting to wake up a VCPU before we free
the VCPUs of the guest. This is accomplished by:
- Forces a PPC_MSG_CALL_FUNCTION IPI to be completed by all CPUs
before freeing any VCPUs in kvm_arch_destroy_vm().
- Any PPC_MSG_RM_HOST_ACTION messages must be executed first
before any other PPC_MSG_CALL_FUNCTION messages.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds real and virtual mode handlers for the H_PUT_TCE_INDIRECT and
H_STUFF_TCE hypercalls for user space emulated devices such as IBMVIO
devices or emulated PCI. These calls allow adding multiple entries
(up to 512) into the TCE table in one call which saves time on
transition between kernel and user space.
The current implementation of kvmppc_h_stuff_tce() allows it to be
executed in both real and virtual modes so there is one helper.
The kvmppc_rm_h_put_tce_indirect() needs to translate the guest address
to the host address and since the translation is different, there are
2 helpers - one for each mode.
This implements the KVM_CAP_PPC_MULTITCE capability. When present,
the kernel will try handling H_PUT_TCE_INDIRECT and H_STUFF_TCE if these
are enabled by the userspace via KVM_CAP_PPC_ENABLE_HCALL.
If they can not be handled by the kernel, they are passed on to
the user space. The user space still has to have an implementation
for these.
Both HV and PR-syle KVM are supported.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The get and set operations got exchanged by mistake when moving the
code from book3s.c to powerpc.c.
Fixes: 3840edc803
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
QEMU assumes 32 memslots if this extension is not implemented. Although,
current value of KVM_USER_MEM_SLOTS is 32, once KVM_USER_MEM_SLOTS
changes QEMU would take a wrong value.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When compiling the KVM code for POWER with "make C=1", sparse
complains about functions missing proper prototypes and a 64-bit
constant missing the ULL prefix. Let's fix this by making the
functions static or by including the proper header with the
prototypes, and by appending a ULL prefix to the constant
PPC_MPPE_ADDRESS_MASK.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This lets the function access the new memory slot without going through
kvm_memslots and id_to_memslot. It will simplify the code when more
than one address space will be supported.
Unfortunately, the "const"ness of the new argument must be casted
away in two places. Fixing KVM to accept const struct kvm_memory_slot
pointers would require modifications in pretty much all architectures,
and is left for later.
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
