Broadcom BCM2712 SoC has an SDHCI card controller using the SDIO CFG
register block present on other STB chips. Add support for BCM2712
SD capabilities of this chipset.
The silicon is SD Express capable but this driver port does not currently
include that feature yet.
Based on downstream driver by raspberry foundation maintained kernel.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/ad2ec39c62c2783dd5de4bf2ec581866e822e2b1.1717061147.git.andrea.porta@suse.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi: Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- renesas_sdhi: Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
- sdhci-acpi: Disable write protect detection on Toshiba WT10-A
- sdhci-acpi: Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654: Re-work and fix the tuning support for multiple speed-modes
- sdhci_am654: Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
- sdhci-of-dwcmshc: Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of PMCSR writes
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback
-----BEGIN PGP SIGNATURE-----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=I2JP
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi:
- Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi:
- Add quirk to enable pull-up on the card-detect GPIO on Asus
T100TA
- Disable write protect detection on Toshiba WT10-A
- Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654:
- Re-work and fix the tuning support for multiple speed-modes
- Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc:
- Add tuning support for Sophgo CV1800B and SG200X
- Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of
PMCSR writes"
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback"
* tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility
dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list
mmc: renesas_sdhi: Set the SDBUF after reset
mmc: core: Increase the timeout period of the ACMD41 command
mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too
mmc: atmel-mci: Switch to use dev_err_probe()
mmc: atmel-mci: Incapsulate used to be a platform data into host structure
mmc: atmel-mci: Replace platform device pointer by generic one
mmc: atmel-mci: Use temporary variable for struct device
mmc: atmel-mci: Get rid of platform data leftovers
mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning
mmc: sdhci-s3c: Choose sdhci_ops based on variant
mmc: sdhci_am654: Constify struct sdhci_ops
mmc: sdhci-sprd: Constify struct sdhci_ops
mmc: sdhci-omap: Constify struct sdhci_ops
mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops
mmc: slot-gpio: Use irq_handler_t type
mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
...
Merge cpuidle updates, changes related to system sleep and power capping
updates for 6.10:
- Fix kerneldoc description of ladder_do_selection() (Jeff Johnson).
- Convert the cpuidle kirkwood driver to platform remove callback
returning void (Yangtao Li).
- Replace deprecated strncpy() with strscpy() in the hibernation core
code (Justin Stitt).
- Use %ps to simplify debug output in the core system-wide suspend and
resume code (Len Brown).
- Remove unnecessary else from device_init_wakeup() and make
device_wakeup_disable() return void (Dhruva Gole).
- Enable PMU support in the Intel TPMI RAPL driver (Zhang Rui).
- Add support for ArrowLake-H platform to the Intel RAPL driver (Zhang
Rui).
- Avoid explicit cpumask allocation on stack in DTPM (Dawei Li).
* pm-cpuidle:
cpuidle: ladder: fix ladder_do_selection() kernel-doc
cpuidle: kirkwood: Convert to platform remove callback returning void
* pm-sleep:
PM: hibernate: replace deprecated strncpy() with strscpy()
PM: sleep: Take advantage of %ps to simplify debug output
PM: wakeup: Remove unnecessary else from device_init_wakeup()
PM: wakeup: make device_wakeup_disable() return void
* pm-powercap:
powercap: intel_rapl_tpmi: Enable PMU support
powercap: intel_rapl: Introduce APIs for PMU support
powercap: intel_rapl: Sort header files
powercap: intel_rapl: Add support for ArrowLake-H platform
powercap: DTPM: Avoid explicit cpumask allocation on stack
- RZ/G2UL and RZ/Five ("r9a07g043")
- RZ/G2L(C) ("r9a07g044")
- RZ/V2L ("r9a07g054")
- RZ/G3S ("r9a08g045")
- RZ/V2M ("r9a09g011")
The above SoCs have HS400 disabled and use fixed address mode. Add a
generic compatible 'renesas,rzg2l-sdhi' fallback string for these SoCs,
where fixed_addr_mode and hs400_disabled quirks are applied.
For backward compatibility, compatible string 'renesas,sdhi-r9a09g011' for
RZ/V2M is retained.
Also rename sdhi_quirks_r9a09g011->sdhi_quirks_rzg2l and
of_r9a09g011_compatible->of_rzg2l_compatible to make it generic.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430145937.133643-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For development purpose, renesas_sdhi_probe() could be called w/
dma_ops = NULL to force the usage of PIO mode. In this case the
renesas_sdhi_enable_dma() will not be called before transferring data.
If renesas_sdhi_enable_dma() is not called, renesas_sdhi_clk_enable()
call from renesas_sdhi_probe() will configure SDBUF by calling the
renesas_sdhi_sdbuf_width() function, but then SDBUF will be reset in
tmio_mmc_host_probe() when calling tmio_mmc_reset() though host->reset().
If SDBUF is zero the data transfer will not work in PIO mode for RZ/G3S.
To fix this call again the renesas_sdhi_sdbuf_width(host, 16) in
renesas_sdhi_reset(). The call of renesas_sdhi_sdbuf_width() was not
removed from renesas_sdhi_clk_enable() as the host->reset() is optional.
Co-developed-by: Hien Huynh <hien.huynh.px@renesas.com>
Signed-off-by: Hien Huynh <hien.huynh.px@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430093724.2692232-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Extensive testing has shown that some specific SD cards require an
increased command timeout to be successfully initialized.
More info:
Platform: Rockchip SoC + DW Multimedia host Controller
SD card: Xvv microSD CMH34A17TMA12 (Made in Korea)
Note: The SD card is custom-made by the customer in collaboration
with the wafer foundry.
Signed-off-by: Felix Qin <xiaokeqinhealth@126.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240429071955.163282-1-xiaokeqinhealth@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Similar to what has already been changed for eMMC and the MMC_SEND_OP_COND
(CMD1), let's convert the SD_APP_OP_COND (ACMD41) for SD cards to use the
common __mmc_poll_for_busy() too.
This change means the initial delay period, that starts as 10ms will now
increase for every loop when being busy. The total accepted timeout for
being busy is 1s, which is according to the SD spec.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Felix Qin <xiaokeqinhealth@126.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240425133034.79599-1-ulf.hansson@linaro.org
After platform data is gone, we always allocate memory for the slot
information. Incapsulate the array of the latter into the host structure,
so we allocate memory only once. This makes code simpler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240425170900.3767990-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.9-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.10.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There no need to keep a pointer to a platform device as it's not
used outside of ->probe() and ->remove() callbacks.
Replace platform device pointer by generic one in host structure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240417165708.2965612-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit d2c6d518c2 ("mmc: atmel-mci: move atmel MCI header file")
made sure that there is no in-kernel user of the platform data. But
at the same time it hadn't removed the code around that data structure.
Finish the job here and remove a dead code.
Fixes: d2c6d518c2 ("mmc: atmel-mci: move atmel MCI header file")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240417165708.2965612-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the .platform_execute_tuning for Sophgo CV1800B and SG200X.
Some code is borrowed from sdhci-esdhc-imx.c. The tuning result is
similar as the one of SoC vendor's SDK.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240420021429.454-1-jszhang@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The preceding "&" before th1520_execute_tuning is useless, remove it.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240414164357.2841-1-jszhang@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The difference between old S3C64xx and newer Exynos4 SDHCI controller
variants is in clock handling (the "no_divider" field in drvdata).
Choose the proper sdhci_ops based on the variant instead of patching
ops in probe, if Exynos4 is used.
This allows making struct sdhci_ops const for code safety and probably
opens further options in the future, as the dynamic pointer ops table is
not anymore that dynamic.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240414-mmc-const-sdhci-ops-v2-5-262f81faadac@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The local struct sdhci_ops can be made const for code safety.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240414-mmc-const-sdhci-ops-v2-3-262f81faadac@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The irq_handler_t is already defined globally, let's use it
in slot-gpio code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240410195618.1632778-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card-detect GPIO for the microSD slot on Asus T100TA / T100TAM models
stopped working under Linux after commit 6fd03f0248 ("gpiolib: acpi:
support bias pull disable").
The GPIO in question is connected to a mechanical switch in the slot
which shorts the pin to GND when a card is inserted.
The GPIO pin correctly gets configured with a 20K pull-up by the BIOS,
but there is a bug in the DSDT where the GpioInt for the card-detect is
configured with a PullNone setting:
GpioInt (Edge, ActiveBoth, SharedAndWake, PullNone, 0x2710,
"\\_SB.GPO0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0026
}
Linux now actually honors the PullNone setting and disables the 20K pull-up
configured by the BIOS.
Add a new DMI_QUIRK_SD_CD_ENABLE_PULL_UP quirk which when set calls
mmc_gpiod_set_cd_config() to re-enable the pull-up and set this for
the Asus T100TA models to fix this.
Fixes: 6fd03f0248 ("gpiolib: acpi: support bias pull disable")
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-7-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the Toshiba WT10-A the microSD slot always reports the card being
write-protected, just like on the Toshiba WT8-B.
Add a DMI quirk to work around this.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-6-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Lenovo Yoga Tablet 2 Pro 1380 sdcard slot has an active high cd pin
and a broken wp pin which always reports the card being write-protected.
Add a DMI quirk to address both issues.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-5-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some mmc host drivers may need to fixup a card-detection GPIO's config
to e.g. enable the GPIO controllers builtin pull-up resistor on devices
where the firmware description of the GPIO is broken (e.g. GpioInt with
PullNone instead of PullUp in ACPI DSDT).
Since this is the exception rather then the rule adding a config
parameter to mmc_gpiod_request_cd() seems undesirable, so instead
add a new mmc_gpiod_set_cd_config() function. This is simply a wrapper
to call gpiod_set_config() on the card-detect GPIO acquired through
mmc_gpiod_request_cd().
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When e.g. 8 bytes are to be read, sgm->consumed equals 8 immediately after
sg_miter_next() call. The driver then increments it as bytes are read,
so sgm->consumed becomes 16 and this warning triggers in sg_miter_stop():
WARN_ON(miter->consumed > miter->length);
WARNING: CPU: 0 PID: 28 at lib/scatterlist.c:925 sg_miter_stop+0x2c/0x10c
CPU: 0 PID: 28 Comm: kworker/0:2 Tainted: G W 6.9.0-rc5-dirty #249
Hardware name: Generic DT based system
Workqueue: events_freezable mmc_rescan
Call trace:.
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x44/0x5c
dump_stack_lvl from __warn+0x78/0x16c
__warn from warn_slowpath_fmt+0xb0/0x160
warn_slowpath_fmt from sg_miter_stop+0x2c/0x10c
sg_miter_stop from moxart_request+0xb0/0x468
moxart_request from mmc_start_request+0x94/0xa8
mmc_start_request from mmc_wait_for_req+0x60/0xa8
mmc_wait_for_req from mmc_app_send_scr+0xf8/0x150
mmc_app_send_scr from mmc_sd_setup_card+0x1c/0x420
mmc_sd_setup_card from mmc_sd_init_card+0x12c/0x4dc
mmc_sd_init_card from mmc_attach_sd+0xf0/0x16c
mmc_attach_sd from mmc_rescan+0x1e0/0x298
mmc_rescan from process_scheduled_works+0x2e4/0x4ec
process_scheduled_works from worker_thread+0x1ec/0x24c
worker_thread from kthread+0xd4/0xe0
kthread from ret_from_fork+0x14/0x38
This patch adds initial zeroing of sgm->consumed. It is then incremented
as bytes are read or written.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: 3ee0e7c3e6 ("mmc: moxart-mmc: Use sg_miter for PIO")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240422153607.963672-1-saproj@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A series of fixes for n8x0 GPIO regressions caused by the changes to use
GPIO descriptors.
-----BEGIN PGP SIGNATURE-----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=pHnd
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=m+W/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v6.9/n8x0-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
GPIO regression fixes for n8x0
A series of fixes for n8x0 GPIO regressions caused by the changes to use
GPIO descriptors.
* tag 'omap-for-v6.9/n8x0-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: fix USB regression on Nokia N8x0
mmc: omap: restore original power up/down steps
mmc: omap: fix deferred probe
mmc: omap: fix broken slot switch lookup
ARM: OMAP2+: fix N810 MMC gpiod table
ARM: OMAP2+: fix bogus MMC GPIO labels on Nokia N8x0
Link: https://lore.kernel.org/r/pull-1712135932-125424@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge the mmc fixes for v6.9-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.10.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix SD card tuning error by increasing tuning loop count
from 40(MAX_TUNING_LOOP) to 128.
For some reason the tuning algorithm requires to move through all the taps
of delay line even if the THRESHOLD_MODE (bit 2 in AT_CTRL_R) is used
instead of the LARGEST_WIN_MODE.
Tested-by: Drew Fustini <drew@pdp7.com>
Tested-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 43658a542e ("mmc: sdhci-of-dwcmshc: Add support for T-Head TH1520")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240402093539.184287-1-bigunclemax@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device_wakeup_disable() call only returns an error if no dev exists,
but there's not much a user can do at that point.
Rather, make this function return void.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge the mmc fixes for v6.9-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.10.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modules registering driver with sdio_register_driver() might
forget to set .owner field. The field is used by some of other kernel
parts for reference counting (try_module_get()), so it is expected that
drivers will set it.
Solve the problem by moving this task away from the drivers to the core
code, just like we did for platform_driver in
commit 9447057eaf ("platform_device: use a macro instead of
platform_driver_register").
Since many drivers forget to set the .owner, this effectively will fix
them. Examples of fixed drivers are: ath6kl, b43, btsdio.c, ks7010,
libertas, MediaTek WiFi drivers, Realtek WiFi drivers, rsi, siano,
wilc1000, wl1251 and more.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240329-module-owner-sdio-v1-1-e4010b11ccaa@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
d7133797e9 ("mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter
ASPM L1.2") and 36ed2fd32b ("mmc: sdhci-pci-gli: A workaround to allow
GL9755 to enter ASPM L1.2") added writes to the Control register in the
Power Management Capability to put the device in D3hot and back to D0.
Use the pci_set_power_state() interface instead because these are generic
operations that don't need to be driver-specific. Also, the PCI spec
requires some delays after these power transitions, and
pci_set_power_state() takes care of those, while d7133797e9 and
36ed2fd32b did not.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20240327214831.1544595-3-helgaas@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
015c9cbcf0 ("mmc: sdhci-pci-gli: GL9750: Mask the replay timer timeout of
AER") added PCI_GLI_9750_CORRERR_MASK, the offset of the AER Capability in
config space, and PCI_GLI_9750_CORRERR_MASK_REPLAY_TIMER_TIMEOUT, the
Replay Timer Timeout bit in the AER Correctable Error Status register.
Use pci_find_ext_capability() to locate the AER Capability and use the
existing PCI_ERR_COR_REP_TIMER definition to mask the bit.
This removes a little bit of unnecessarily device-specific code and makes
AER-related things more greppable.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20240327214831.1544595-2-helgaas@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert the existing symbolic permissions to the octal presentation as
this is the preferred representation for debugfs permissions.
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Link: https://lore.kernel.org/r/20240326094215.212930-1-r.czerwinski@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Generic sdhci code registers LED device and uses host->runtime_suspended
flag to protect access to it. The sdhci-msm driver doesn't set this flag,
which causes a crash when LED is accessed while controller is runtime
suspended. Fix this by setting the flag correctly.
Cc: stable@vger.kernel.org
Fixes: 67e6db113c ("mmc: sdhci-msm: Add pm_runtime and system PM support")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240321-sdhci-mmc-suspend-v1-1-fbc555a64400@8devices.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using __exit for the remove function results in the remove callback being
discarded with CONFIG_MMC_DAVINCI=y. When such a device gets unbound (e.g.
using sysfs or hotplug), the driver is just removed without the cleanup
being performed. This results in resource leaks. Fix it by compiling in the
remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: drivers/mmc/host/davinci_mmc: section mismatch in
reference: davinci_mmcsd_driver+0x10 (section: .data) ->
davinci_mmcsd_remove (section: .exit.text)
Fixes: b4cff4549b ("DaVinci: MMC: MMC/SD controller driver for DaVinci family")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240324114017.231936-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For enabling CQE support just set 'supports-cqe' in your DevTree file
for appropriate mmc node.
Signed-off-by: Sergey Khimich <serghox@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240319115932.4108904-3-serghox@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are could be specific limitations for some mmc
controllers for setting cqhci transfer descriptors.
So add callback to allow implement driver specific function.
Signed-off-by: Sergey Khimich <serghox@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240319115932.4108904-2-serghox@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_am654_set_clock function is also used to enable
delay chain, therefore fix comments to be more generic in
case we are not enabling DLL.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-6-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While integer type works, the otap_del_sel and itap_del_sel
arrays are manipulated as u32, so change array types to u32.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-5-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While STRB is currently used for DATA and CRC responses, the CMD
responses from the device to the host still require ITAPDLY for
HS400 timing.
Currently what is stored for HS400 is the ITAPDLY from High Speed
mode which is incorrect. The ITAPDLY for HS400 speed mode should
be the same as ITAPDLY as HS200 timing after tuning is executed.
Add the functionality to save ITAPDLY from HS200 tuning and save
as HS400 ITAPDLY.
Fixes: a161c45f29 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-8-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ITAPDLYSEL to sdhci_j721e_4bit_set_clock function.
This allows to set the correct ITAPDLY for timings that
do not carry out tuning.
Fixes: 1accbced1c ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-7-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the OTAP/ITAP delay enable functionality is incorrect in
the am654_set_clock function. The OTAP delay is not enabled when
timing < SDR25 bus speed mode. The ITAP delay is not enabled for
timings that do not carry out tuning.
Add this OTAP/ITAP delay functionality according to the datasheet
[1] OTAPDLYENA and ITAPDLYENA for MMC0.
[1] https://www.ti.com/lit/ds/symlink/am62p.pdf
Fixes: 8ee5fc0e0b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-4-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For DDR52 timing, DLL is enabled but tuning is not carried
out, therefore the ITAPDLY value in PHY CTRL 4 register is
not correct. Fix this by writing ITAPDLY after enabling DLL.
Fixes: a161c45f29 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-3-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the sdhci_am654 driver only supports one tuning
algorithm which should be used only when DLL is enabled. The
ITAPDLY is selected from the largest passing window and the
buffer is viewed as a circular buffer.
The new algorithm should be used when the delay chain
is enabled. The ITAPDLY is selected from the largest passing
window and the buffer is not viewed as a circular buffer.
This implementation is based off of the following paper: [1].
Also add support for multiple failing windows.
[1] https://www.ti.com/lit/an/spract9/spract9.pdf
Fixes: 13ebeae68a ("mmc: sdhci_am654: Add support for software tuning")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-2-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
