The X2 crystal oscillator on the Koelsch development board provides a
74.25 MHz clock, not a 148.5 MHz clock.
Fixes: cd21cb46e1 ("ARM: shmobile: koelsch: Add DU external pixel clocks to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7791.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
And the sd-uhs-sdr104 property to SDHI0.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C1 on the EXIO-C connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased and fixed aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add support in the dts for the HDMI input. Based on the Lager dts
patch from Ulrich Hecht.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[uli: removed "renesas," prefixes from pfc nodes]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1,2}.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Name the Pin Function Controller subnodes for QSPI and MSIOF0 after
their device names, instead of after the spi interface aliases.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /regulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@5 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=k7qU
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
This is a backmerge of v4.6 fixes, to avoid a merge conflict between 4.6
and our next/dt branch.
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
clk_get on a disabled clock node will return EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their clocks property.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them to prevent this.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Fixed rate and fixed factor clocks do not require an
clock-output-names property.
* Since 07705583e9 ("clk: shmobile: div6: Make clock-output-names
optional") Renesas div6 clocks do not require a clock-output-names
property.
In the above cases there is only one clock output and its name is taken
from that of the clock node. Accordingly, remove the unnecessary
clock-output-names properties and as necessary update the node names.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the koelsch device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates:
- SCIF:
- Supports now 50, 75, 110, 1152000, 1500000, 2000000, and
4000000 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- More accurate 576000 bps.
- HSCIF:
- Supports now 50, 75, 110, 134, 150, and 200 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- More accurate 576000, 1152000, 3000000, 3500000, and 4000000
bps.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The signals output by the DU to the HDMI transmitter use full 24-bit
RGB. Make sure all pins are properly muxed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support
partitions in a special 'partitions' subnode"), having partitions as
direct subnodes of an mtd device is discouraged:
spi0.0: 'partitions' subnode not found on /spi@e6b10000/flash@0. Trying to parse direct subnodes as partitions.
Hence move the SPI FLASH partitions to a "partitions" subnode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Because of historical reason, audio clock didn't use CCF.
Let's use it now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It is easy to modify settings for Test or other purpose if sound has label
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OIk0
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
* tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7794 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791: add MMCIF max-frequency
ARM: shmobile: r8a7790: add MMCIF max-frequency
ARM: shmobile: bockw dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: henninger dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: bockw-reference dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: koelsch dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: lager dts: Replace "nor-jedec" by "jedec,spi-nor"
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OdRc
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: shmobile: r8a7791: Enable DMA for HSUSB
ARM: shmobile: r8a7791: add USB-DMAC device nodes
ARM: shmobile: r8a7790: Enable DMA for HSUSB
ARM: shmobile: r8a7790: add USB-DMAC device nodes
ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
ARM: shmobile: koelsch dts: Use generic names for device nodes
ARM: shmobile: lager dts: Use generic names for device nodes
ARM: shmobile: bockw dts: Use generic names for device nodes
ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
ARM: shmobile: lager dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
ARM: shmobile: marzen dts: Use generic names for device nodes
ARM: shmobile: kzm9d dts: Use generic names for device nodes
ARM: shmobile: ape6evm dts: Use generic names for device nodes
ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
...
Spansion s25fl512s is compatible with "nor-jedec". Hence add the
"nor-jedec" compatible value, so the driver can bind against the generic
name, cfr. commit 8ff16cf77c ("Documentation: devicetree: m25p80:
add "nor-jedec" binding").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The adv7511 IRQ is low level triggered, not falling edge triggered. The
wrong sense configuration results in no interrupt being triggered at
all, breaking hotplug detection. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Fixes: 83a0731b39 ("ARM: shmobile: koelsch: Add DU HDMI output support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Add a device node for the da9063 PMIC, with subnodes for rtc and wdt.
Regulator support is not yet included.
This allows the system to be restarted when the watchdog timer times
out, or when a system restart is requested.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The da9210 regulator is connected to IRQ2. Reflect this in its device
node, so the driver can use it when it gains interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 148.5MHz pixel clocks connected to the DU clock
inputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector
and configure the DISP pin group that drives the HDMI transmitter DE
pin.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VWG8
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Cleanups for v3.20" from Simon
Horman:
Second Round of Renesas ARM Based SoC DT Cleanups for v3.20
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
* tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7790: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7791 dtsi: Drop "renesas,rcar_sound" compatible value
ARM: shmobile: r8a7790 dtsi: Drop "renesas,rcar_sound" compatible value
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fZ4r
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v3.20" from Simon Horman:
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
* tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
ARM: shmobile: r8a7791: add MLB+ clock
ARM: shmobile: r8a7790: add MLB+ clock
ARM: shmobile: ape6evm: Fix LAN9220 VDDVARIO voltage
ARM: shmobile: r8a73a4: Add r8a73a4-ape6evm.dtb to ARCH_SHMOBILE_MULTI
ARM: shmobile: ape6evm: Add keypad to the device tree
ARM: shmobile: ape6evm: Add LEDs to the device tree
ARM: shmobile: ape6evm: synchronize dts with reference platform
ARM: shmobile: ape6evm: fix compatible string for Ethernet controller
ARM: shmobile: r8a7794: Add MMCIF clock to device tree
ARM: shmobile: r8a7794: Add SDHI clocks to device tree
ARM: shmobile: r8a7794: Add I2C clocks to device tree
ARM: shmobile: r8a7779: Add TWD device to DTS
ARM: shmobile: r8a7779: Use MSTP for SCIF clocks
ARM: shmobile: r8a7779: Use R8A7779_CLK_P as SCIF parent clock
ARM: shmobile: r8a7794: Add QSPI clock to device tree
ARM: shmobile: lager: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add SYS-DMAC clocks to device tree
ARM: shmobile: r8a7791: Add IPMMU-SGX clock to device tree
ARM: shmobile: koelsch: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add USBDMAC[01] clocks to device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
There's no reason to name the only two available serial ports on the
board ttySC6 and ttySC7 (apart from confusing userspace, which we should
try to avoid).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to change into mode3, CPOL and CPHA bit of SPCMD register
of QSPI is changed. Mode3 can avoid intermediate voltage.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
[horms: Updated changelog and re-ordered properties]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Update the size and names of flash partitions to match the
expectations of the loader which are as follows:
"loader"---0x0000_0000-0x0008_0000 [loader program (readonly)]
"user" ---0x0008_0000-0x0060_0000 [U-Boot + bootargs + dt + uImage (readonly)]
"flash" ---0x0060_0000-0x0400_0000 [filesystem and free (read/write)]
["user"'s assumed breakdown]
U-boot (0x0008_0000-0x000c_0000) 256KiB
bootargs (0x000c_0000-0x0010_0000) 256KiB
Device tree (0x0010_0000-0x0014_0000) 256KiB
zImage (0x0014_0000-0x0060_0000) 4.75MiB
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
While the DT parsing code recognizes "ok" as a valid value for the
"status" property, ePAPR v1.1 doesn't mention it in the list of valid
values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
* Add labels for LEDs on kzm9g-reference and koelsch
* Add Sound support to r8a7790/lager and r8a7791/koelsch
* Add IIC DMA nodes to r8a7790 and r8a7791
* Use SoC-specific IIC compatible properties on sh73a0 and r8a73a4
* Add SGX, MMP and VSP1 clocks to r8a7794
* Add USBDMAC{0,1} clocks to r8a7790 and r8a7791
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUbbZkAAoJENfPZGlqN0++A0gQAJ5bs24c0fRzIPXrkeIzY0aQ
262nBv175LG8wihixOAJB/jiTPSpaZavlR+iXYq2iU+IqkkwIzFtdNs4q/ZMdppW
J7LPUj0DwJe6+B8AYhSsSDDNW0P4avBXfU4rFXzLp2IkAqi/HdxJjB3/9C5Nzi7b
mpsTvz3x4iP2NZdEKIDGtMBwtjghsfKBRaLsgNow+JdxLDLuWKWjaR8PMxvF1LFa
Z/jz343PmFGCaWypq5HVyu+h3eNvh9HpOUleurGijXzoZl61U1SDceTygfbF+Ht2
nNq8gqynokYWfmDQa8HJlPEmeCFhDtBHc9NNPJBEOCv7pWWdsXgfEYW5OepH+xzp
FqfXM2DwKVMDcSL3LDwXYT1xZQfI8KUDg6ek5gXk8pDDpVhAb2ishEt+Vr3zEL+H
uro9wruHl8lYujq9P4Jmh9icl2fMx3hXIoq3PVkzOkmJhViwSm55pqlAAVN72d4u
xIthmwmvQ/zsvn5RwV3jmWUlwlYJmMz2gXqtsq+9NUy55yUMqjeSB9kchTzrM6SJ
CzfiCl5j2SC6jiCNGsiFjI603kdIKq0uvaLQStEAHoWJkuf+jEWmfjV9qPptE+sa
rPhIhWUXqs5Emw3DgQynIOy+szTWlg1hJl9MDF/SaeiyZ/dh/teqIoYhAjfqlCFS
7etGw24D7YujpG9jlfC4
=0cH9
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v3.19" from Simon Horman:
* Add labels for LEDs on kzm9g-reference and koelsch
* Add Sound support to r8a7790/lager and r8a7791/koelsch
* Add IIC DMA nodes to r8a7790 and r8a7791
* Use SoC-specific IIC compatible properties on sh73a0 and r8a73a4
* Add SGX, MMP and VSP1 clocks to r8a7794
* Add USBDMAC{0,1} clocks to r8a7790 and r8a7791
* tag 'renesas-dt2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (29 commits)
ARM: shmobile: r8a7791: add USBDMAC{0,1} clocks to device tree
ARM: shmobile: r8a7790: add USBDMAC{0,1} clocks to device tree
ARM: shmobile: r8a7794: Add MMP and VSP1 clocks to device tree
ARM: shmobile: r8a7794: Add SGX clock to device tree
ARM: shmobile: koelsch: add Volume Ramp usage on comment
ARM: shmobile: lager: add Volume Ramp usage on comment
ARM: shmobile: r8a7791: add DMA nodes for IIC
ARM: shmobile: r8a7790: add DMA nodes for IIC
ARM: shmobile: kzm9g-reference dts: Add labels for the LEDs
ARM: shmobile: koelsch dts: Add labels for the LEDs
ARM: shmobile: sh73a0 dtsi: Add SoC-specific IIC compatible properties
ARM: shmobile: r8a73a4 dtsi: Add SoC-specific IIC compatible properties
ARM: shmobile: koelsch: Sound DMA support via DVC on DTS
ARM: shmobile: koelsch: Sound DMA support via SRC on DTS
ARM: shmobile: koelsch: Sound DMA support via BUSIF on DTS
ARM: shmobile: koelsch: Sound DMA support on DTS
ARM: shmobile: koelsch: Sound PIO support on DTS
ARM: shmobile: koelsch: fixup I2C2 clock frequency
ARM: shmobile: lager: Sound DMA support via DVC on DTS
ARM: shmobile: lager: Sound DMA support via SRC on DTS
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Use keyboard as gpio-keys node name
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=H8mr
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Third Round of Renesas ARM Based SoC DT Cleanups for v3.19" from Simon Horman:
* Use keyboard as gpio-keys node name
* tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference: Use keyboard as gpio-keys node name
ARM: shmobile: koelsch: Use keyboard as gpio-keys node name
ARM: shmobile: lager: Use keyboard as gpio-keys node name
ARM: shmobile: armadillo800eva: Use keyboard as gpio-keys node name
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The LEDs on the koelsch board are labeled using upper-case characters.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
