The Freescale M5249EVB board is fitted with an SMC LAN91c11 ethernet
device. Add platform support to the M5249EVB setup code to support this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware. This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The older simple ColdFire interrupt controller has no one-to-one mapping
of interrupt numbers to bits in the interrupt mask register. Create a
mapping array that each ColdFire CPU type can populate with its available
interrupts and the bits that each use in the interrupt mask register.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire "timers" clock setup can be simplified. There is really no
need for the flexible per-platform setup code. The clock interrupt can be
hard defined per CPU platform (in CPU include files). This makes the
actual timer code simpler.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently the code that supports setting the old style ColdFire interrupt
controller mask registers is macros in the include files of each of the
CPU types. Merge all these into a set of real masking functions in the
old Coldfire interrupt controller code proper. All the macros are basically
the same (excepting a register size difference on really early parts).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Each of the ColdFire CPU platform code that used the old style interrupt
controller had its own copy of the mcf_autovector() function. They are all
the same, remove them all and create a single function in the common
coldfire/intc.c code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The address of the IVUR register is not correct, it should be offset
into the MBAR region. Without this the vector is not set to the correct
number.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ICR registers of the 5249 ColdFire processor are 8bits, not 32bits.
Fix the read/write of these register to be the correct size.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The UART platform data structure is missing an empty struct at the
end (as the end of structure marker).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove all the dead timer interrupt checking functions for the ColdFire
CPU "timers" hardware that are not used after switching to GENERIC_TIME.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to platform style configuration for 5249 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce the function pointer mess of the m68knommu timer code by calling
directly to the local hardware's timer setup, and expose the local
common timer interrupt handler to the lower level hardware timer.
Ultimately this will save definitions of all these functions across all
the platform code to setup the function pointers (which for any given
m68knommu CPU family member can be only one set of hardware timer
functions).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch to using the generic irq framework removed the
coldfire_trap_init() code, so remove all references to it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently most of the m68knommu cpu/board setup files are handling
the setup of fixed boot parameters (via CONFIG_BOOTPARAM) themselves.
Move all this into the common setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
