After successfully probed, ci->role_switch would only be NULL or a valid
pointer. IS_ERR(ci->role_switch) will always return 0. So no need to wrap
it with IS_ERR, otherwise the logic is wrong.
Fixes: e1b5d2bed6 ("usb: chipidea: core: handle usb role switch in a common way")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20221215055409.3760523-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 ports on xHC hosts may have retimers that cause too long
exit latency to work with native USB3 U1/U2 link power management states.
For now only use usb_acpi_port_lpm_incapable() to evaluate if port lpm
should be disabled while setting up the USB3 roothub.
Other ways to identify lpm incapable ports can be added here later if
ACPI _DSM does not exist.
Limit this to Intel hosts for now, this is to my knowledge only
an Intel issue.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to evaluate ACPI usb device specific method (_DSM) provided
in case the USB3 port shouldn't enter U1 and U2 link states.
This _DSM was added as port specific retimer configuration may lead to
exit latencies growing beyond U1/U2 exit limits, and OS needs a way to
find which ports can't support U1/U2 link power management states.
This _DSM is also used by windows:
Link: https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/usb-device-specific-method---dsm-
Some patch issues found in testing resolved by Ron Lee
Cc: stable@vger.kernel.org
Tested-by: Ron Lee <ron.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race
and cause null pointer dereference when host suddenly dies.
Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id]
virt device at the same time that xhci_kill_endpoint_urbs() tries to
loop through all the device's endpoints, checking if there are any
cancelled urbs left to give back.
hold the xhci spinlock while freeing the virt device
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the host controller is not responding, all URBs queued to all
endpoints need to be killed. This can cause a kernel panic if we
dereference an invalid endpoint.
Fix this by using xhci_get_virt_ep() helper to find the endpoint and
checking if the endpoint is valid before dereferencing it.
[233311.853271] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[233311.853393] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
[233311.853964] pc : xhci_hc_died+0x10c/0x270
[233311.853971] lr : xhci_hc_died+0x1ac/0x270
[233311.854077] Call trace:
[233311.854085] xhci_hc_died+0x10c/0x270
[233311.854093] xhci_stop_endpoint_command_watchdog+0x100/0x1a4
[233311.854105] call_timer_fn+0x50/0x2d4
[233311.854112] expire_timers+0xac/0x2e4
[233311.854118] run_timer_softirq+0x300/0xabc
[233311.854127] __do_softirq+0x148/0x528
[233311.854135] irq_exit+0x194/0x1a8
[233311.854143] __handle_domain_irq+0x164/0x1d0
[233311.854149] gic_handle_irq.22273+0x10c/0x188
[233311.854156] el1_irq+0xfc/0x1a8
[233311.854175] lpm_cpuidle_enter+0x25c/0x418 [msm_pm]
[233311.854185] cpuidle_enter_state+0x1f0/0x764
[233311.854194] do_idle+0x594/0x6ac
[233311.854201] cpu_startup_entry+0x7c/0x80
[233311.854209] secondary_start_kernel+0x170/0x198
Fixes: 50e8725e7c ("xhci: Refactor command watchdog and fix split string.")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <0fe978ed-8269-9774-1c40-f8a98c17e838@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit e00b488e81 ("usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS")
blacklists UAS for all of RTL9210 enclosures.
The RTL9210 controller was advertised with UAS since its release back in
2019 and was shipped with a lot of enclosure products with different
firmware combinations.
Blacklist UAS only for HIKSEMI MD202.
This should hopefully be replaced with more robust method than just
comparing strings. But with limited information [1] provided thus far
(dmesg when the device is plugged in, which includes manufacturer and
product, but no lsusb -v to compare against), this is the best we can do
for now.
[1] https://lore.kernel.org/all/20230109115550.71688-1-qkrwngud825@gmail.com
Fixes: e00b488e81 ("usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS")
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Hongling Zeng <zenghongling@kylinos.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Juhyung Park <qkrwngud825@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20230117085154.123301-1-qkrwngud825@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer and Gerald Lee have identified a use-after-free bug
in the gadgetfs driver, involving processes concurrently mounting and
unmounting the gadgetfs filesystem. In particular, gadgetfs_fill_super()
can race with gadgetfs_kill_sb(), causing the latter to deallocate
the_device while the former is using it. The output from KASAN says,
in part:
BUG: KASAN: use-after-free in instrument_atomic_read_write include/linux/instrumented.h:102 [inline]
BUG: KASAN: use-after-free in atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
BUG: KASAN: use-after-free in __refcount_sub_and_test include/linux/refcount.h:272 [inline]
BUG: KASAN: use-after-free in __refcount_dec_and_test include/linux/refcount.h:315 [inline]
BUG: KASAN: use-after-free in refcount_dec_and_test include/linux/refcount.h:333 [inline]
BUG: KASAN: use-after-free in put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
BUG: KASAN: use-after-free in gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
Write of size 4 at addr ffff8880276d7840 by task syz-executor126/18689
CPU: 0 PID: 18689 Comm: syz-executor126 Not tainted 6.1.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
...
atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
__refcount_sub_and_test include/linux/refcount.h:272 [inline]
__refcount_dec_and_test include/linux/refcount.h:315 [inline]
refcount_dec_and_test include/linux/refcount.h:333 [inline]
put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
deactivate_locked_super+0xa7/0xf0 fs/super.c:332
vfs_get_super fs/super.c:1190 [inline]
get_tree_single+0xd0/0x160 fs/super.c:1207
vfs_get_tree+0x88/0x270 fs/super.c:1531
vfs_fsconfig_locked fs/fsopen.c:232 [inline]
The simplest solution is to ensure that gadgetfs_fill_super() and
gadgetfs_kill_sb() are serialized by making them both acquire a new
mutex.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+33d7ad66d65044b93f16@syzkaller.appspotmail.com
Reported-and-tested-by: Gerald Lee <sundaywind2004@gmail.com>
Link: https://lore.kernel.org/linux-usb/CAO3qeMVzXDP-JU6v1u5Ags6Q-bb35kg3=C6d04DjzA9ffa5x1g@mail.gmail.com/
Fixes: e5d82a7360 ("vfs: Convert gadgetfs to use the new mount API")
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Y6XCPXBpn3tmjdCC@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After doorbell DMA fetches the TRB. If during dequeuing request
driver changes NORMAL TRB to LINK TRB but doesn't delete it from
controller cache then controller will handle cached TRB and packet
can be lost.
The example scenario for this issue looks like:
1. queue request - set doorbell
2. dequeue request
3. send OUT data packet from host
4. Device will accept this packet which is unexpected
5. queue new request - set doorbell
6. Device lost the expected packet.
By setting DFLUSH controller clears DRDY bit and stop DMA transfer.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20221115100039.441295-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the USB serial console device ID for Siemens SCALANCE LPE-9000
which have a USB port for their serial console.
Signed-off-by: Michael Adler <michael.adler@siemens.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCY76ohgAKCRCAXGG7T9hj
vo8fAP0XJ94B7asqcN4W3EyeyfqxUf1eZvmWRhrbKqpLnmHLaQEA/uJBkXL49Zj7
TTcbxR1coJ/hPwhtmONU4TNtCZ+RXw0=
=2Ib5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- two cleanup patches
- a fix of a memory leak in the Xen pvfront driver
- a fix of a locking issue in the Xen hypervisor console driver
* tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: free active map buffer on pvcalls_front_free_map
hvc/xen: lock console list traversal
x86/xen: Remove the unused function p2m_index()
xen: make remove callback of xen driver void returned
The list API provides the list_count_nodes() to help with counting
existing nodes in the list. Utilise it.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221130134838.23805-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI allows the USB PD capabilities to be read with the GET_PDO
command. This will register those capabilities and make them
visible to user space.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Rajaram Regupathy <rajaram.regupathy@intel.com>
Signed-off-by: Rajaram Regupathy <rajaram.regupathy@intel.com>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Link: https://lore.kernel.org/r/20230102062108.838423-1-saranya.gopal@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221212212717.3774606-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fb1f16d74e ("usb: gadget: f_fs: change ep->status safe in
ffs_epfile_io()") added a new ffs_io_data::status field to fix lifetime
issues in synchronous requests.
While there are no similar lifetime issues for asynchronous requests
(the separate ep member in ffs_io_data avoids them) using the status
field means the USB request can be freed earlier and that there is more
consistency between the synchronous and asynchronous I/O paths.
Cc: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20221124170430.3998755-1-john@metanate.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When request_irq(ires1->start) failed in w5300_hw_probe(), irq
ires->start has not been freed, and on the clean_up3 error path,
we also need to free ires1->start irq, fix it.
In addition, We should add free_irq in fusb300_remove(), and give
the lables a proper name so that they can be understood easily,
so add free_irq in fusb300_remove(), and update clean_up3 to
err_alloc_request.
Fixes: 0fe6f1d1f6 ("usb: udc: add Faraday fusb300 driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221123014121.1989721-1-cuigaosheng1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exporsing HotPlugDetect(HPD) helps userspace to infer HPD
state as defined by VESA DisplayPort Alt Mode on USB Type-C Standard.
This allows userspace to notify users for self help, for instance,
to hint user that the display port cable is probably detached (or)
the display port sink (viz., monitors ect.,) is un-powered.
Also helps to debug issues reported from field.
This change adds an additional attribute "hpd" to the existing
"displayport" attributes.
VESA DisplayPort Alt Mode on USB Type-C Standard defines how
HotPlugDetect(HPD) shall be supported on the USB-C connector
when operating in DisplayPort Alt Mode. This is a read only
node which reflects the current state of HPD.
Valid values:
- 1 when HPD’s logical state is high (HPD_High)
- 0 when HPD’s logical state is low (HPD_Low)
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221211193755.1392128-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
Fixes: 4db0fbb601 ("usb: dwc3: gadget: Don't delay End Transfer on delayed_status")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1617a323e190b9cc408fb8b65456e32b5814113.1670546756.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added gpio consumer calls cause a build failure in configurations
that fail to include the right header implicitly:
drivers/usb/dwc3/dwc3-xilinx.c: In function 'dwc3_xlnx_init_zynqmp':
drivers/usb/dwc3/dwc3-xilinx.c:207:22: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_clk_get_optional'? [-Werror=implicit-function-declaration]
207 | reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
| ^~~~~~~~~~~~~~~~~~~~~~~
| devm_clk_get_optional
Fixes: ca05b38252 ("usb: dwc3: xilinx: Add gpio-reset support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230103121755.956027-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 5f217ccd52 ("fotg210-udc: Support optional external PHY"),
the error code is re-assigned to 0 in fotg210_udc_probe(), if allocate or
map memory fails after the assignment, it can't return an error code. Set
the error code to -ENOMEM to fix this problem.
Fixes: 5f217ccd52 ("fotg210-udc: Support optional external PHY")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221230065427.944586-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fotg210 module combines the HCD and OTG drivers, which then
fails to build when only the USB gadget support is enabled
in the kernel but host support is not:
aarch64-linux-ld: drivers/usb/fotg210/fotg210-core.o: in function `fotg210_init':
fotg210-core.c:(.init.text+0xc): undefined reference to `usb_disabled'
Move the check for usb_disabled() after the check for the HCD module,
and let the OTG driver still be probed in this configuration.
A nicer approach might be to have the common portion built as a
library module, with the two platform other files registering
their own platform_driver instances separately.
Fixes: ddacd6ef44 ("usb: fotg210: Fix Kconfig for USB host modules")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221215165728.2062984-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since moving to memalloc_nofs_save/restore, SUNRPC has stopped setting the
GFP_NOIO flag on sk_allocation which the networking system uses to decide
when it is safe to use current->task_frag. The results of this are
unexpected corruption in task_frag when SUNRPC is involved in memory
reclaim.
The corruption can be seen in crashes, but the root cause is often
difficult to ascertain as a crashing machine's stack trace will have no
evidence of being near NFS or SUNRPC code. I believe this problem to
be much more pervasive than reports to the community may indicate.
Fix this by having kernel users of sockets that may corrupt task_frag due
to reclaim set sk_use_task_frag = false. Preemptively correcting this
situation for users that still set sk_allocation allows them to convert to
memalloc_nofs_save/restore without the same unexpected corruptions that are
sure to follow, unlikely to show up in testing, and difficult to bisect.
CC: Philipp Reisner <philipp.reisner@linbit.com>
CC: Lars Ellenberg <lars.ellenberg@linbit.com>
CC: "Christoph Böhmwalder" <christoph.boehmwalder@linbit.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Josef Bacik <josef@toxicpanda.com>
CC: Keith Busch <kbusch@kernel.org>
CC: Christoph Hellwig <hch@lst.de>
CC: Sagi Grimberg <sagi@grimberg.me>
CC: Lee Duncan <lduncan@suse.com>
CC: Chris Leech <cleech@redhat.com>
CC: Mike Christie <michael.christie@oracle.com>
CC: "James E.J. Bottomley" <jejb@linux.ibm.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Valentina Manea <valentina.manea.m@gmail.com>
CC: Shuah Khan <shuah@kernel.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: David Howells <dhowells@redhat.com>
CC: Marc Dionne <marc.dionne@auristor.com>
CC: Steve French <sfrench@samba.org>
CC: Christine Caulfield <ccaulfie@redhat.com>
CC: David Teigland <teigland@redhat.com>
CC: Mark Fasheh <mark@fasheh.com>
CC: Joel Becker <jlbec@evilplan.org>
CC: Joseph Qi <joseph.qi@linux.alibaba.com>
CC: Eric Van Hensbergen <ericvh@gmail.com>
CC: Latchesar Ionkov <lucho@ionkov.net>
CC: Dominique Martinet <asmadeus@codewreck.org>
CC: Ilya Dryomov <idryomov@gmail.com>
CC: Xiubo Li <xiubli@redhat.com>
CC: Chuck Lever <chuck.lever@oracle.com>
CC: Jeff Layton <jlayton@kernel.org>
CC: Trond Myklebust <trond.myklebust@hammerspace.com>
CC: Anna Schumaker <anna@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Here is the large set of USB and Thunderbolt driver changes for 6.2-rc1.
Overall, thanks to the removal of a driver, more lines were removed than
added, a nice change. Highlights include:
- removal of the sisusbvga driver that was not used by anyone anymore
- minor thunderbolt driver changes and tweaks
- chipidea driver updates
- usual set of typec driver features and hardware support added
- musb minor driver fixes
- fotg210 driver fixes, bringing that hardware back from the "dead"
- minor dwc3 driver updates
- addition, and then removal, of a list.h helper function for many USB
and other subsystem drivers, that ended up breaking the build. That
will come back for 6.3-rc1, it missed this merge window.
- usual xhci updates and enhancements
- usb-serial driver updates and support for new devices
- other minor USB driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wvYg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl5DACgssl/ag4zDePHpfoiG5zEGEzH8XsAoMFrzvzu
d43hsH3qsfDGSZRkJJMu
=ORDd
-----END PGP SIGNATURE-----
Merge tag 'usb-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt driver updates from Greg KH:
"Here is the large set of USB and Thunderbolt driver changes for
6.2-rc1. Overall, thanks to the removal of a driver, more lines were
removed than added, a nice change. Highlights include:
- removal of the sisusbvga driver that was not used by anyone anymore
- minor thunderbolt driver changes and tweaks
- chipidea driver updates
- usual set of typec driver features and hardware support added
- musb minor driver fixes
- fotg210 driver fixes, bringing that hardware back from the "dead"
- minor dwc3 driver updates
- addition, and then removal, of a list.h helper function for many
USB and other subsystem drivers, that ended up breaking the build.
That will come back for 6.3-rc1, it missed this merge window.
- usual xhci updates and enhancements
- usb-serial driver updates and support for new devices
- other minor USB driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (153 commits)
usb: gadget: uvc: Rename bmInterfaceFlags -> bmInterlaceFlags
usb: dwc2: power on/off phy for peripheral mode in dual-role mode
usb: dwc2: disable lpm feature on Rockchip SoCs
dt-bindings: usb: mtk-xhci: add support for mt7986
usb: dwc3: core: defer probe on ulpi_read_id timeout
usb: ulpi: defer ulpi_register on ulpi_read_id timeout
usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support
dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller
dt-bindings: vendor-prefixes: add Genesys Logic
usb: fotg210-udc: fix potential memory leak in fotg210_udc_probe()
usb: typec: tipd: Set mode of operation for USB Type-C connector
usb: gadget: udc: drop obsolete dependencies on COMPILE_TEST
usb: musb: remove extra check in musb_gadget_vbus_draw
usb: gadget: uvc: Prevent buffer overflow in setup handler
usb: dwc3: qcom: Fix memory leak in dwc3_qcom_interconnect_init
usb: typec: wusb3801: fix fwnode refcount leak in wusb3801_probe()
usb: storage: Add check for kcalloc
USB: sisusbvga: use module_usb_driver()
USB: sisusbvga: rename sisusb.c to sisusbvga.c
USB: sisusbvga: remove console support
...
Since commit fc7a6209d5 ("bus: Make remove callback return void")
forces bus_type::remove be void-returned, it doesn't make much sense for
any bus based driver implementing remove callbalk to return non-void to
its caller.
This change is for xen bus based drivers.
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Link: https://lore.kernel.org/r/TYCP286MB23238119AB4DF190997075C9CAE39@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Juergen Gross <jgross@suse.com>
API:
- Optimise away self-test overhead when they are disabled.
- Support symmetric encryption via keyring keys in af_alg.
- Flip hwrng default_quality, the default is now maximum entropy.
Algorithms:
- Add library version of aesgcm.
- CFI fixes for assembly code.
- Add arm/arm64 accelerated versions of sm3/sm4.
Drivers:
- Remove assumption on arm64 that kmalloc is DMA-aligned.
- Fix selftest failures in rockchip.
- Add support for RK3328/RK3399 in rockchip.
- Add deflate support in qat.
- Merge ux500 into stm32.
- Add support for TEE for PCI ID 0x14CA in ccp.
- Add mt7986 support in mtk.
- Add MaxLinear platform support in inside-secure.
- Add NPCM8XX support in npcm.
-----BEGIN PGP SIGNATURE-----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=OpWt
-----END PGP SIGNATURE-----
Merge tag 'v6.2-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Optimise away self-test overhead when they are disabled
- Support symmetric encryption via keyring keys in af_alg
- Flip hwrng default_quality, the default is now maximum entropy
Algorithms:
- Add library version of aesgcm
- CFI fixes for assembly code
- Add arm/arm64 accelerated versions of sm3/sm4
Drivers:
- Remove assumption on arm64 that kmalloc is DMA-aligned
- Fix selftest failures in rockchip
- Add support for RK3328/RK3399 in rockchip
- Add deflate support in qat
- Merge ux500 into stm32
- Add support for TEE for PCI ID 0x14CA in ccp
- Add mt7986 support in mtk
- Add MaxLinear platform support in inside-secure
- Add NPCM8XX support in npcm"
* tag 'v6.2-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (184 commits)
crypto: ux500/cryp - delete driver
crypto: stm32/cryp - enable for use with Ux500
crypto: stm32 - enable drivers to be used on Ux500
dt-bindings: crypto: Let STM32 define Ux500 CRYP
hwrng: geode - Fix PCI device refcount leak
hwrng: amd - Fix PCI device refcount leak
crypto: qce - Set DMA alignment explicitly
crypto: octeontx2 - Set DMA alignment explicitly
crypto: octeontx - Set DMA alignment explicitly
crypto: keembay - Set DMA alignment explicitly
crypto: safexcel - Set DMA alignment explicitly
crypto: hisilicon/hpre - Set DMA alignment explicitly
crypto: chelsio - Set DMA alignment explicitly
crypto: ccree - Set DMA alignment explicitly
crypto: ccp - Set DMA alignment explicitly
crypto: cavium - Set DMA alignment explicitly
crypto: img-hash - Fix variable dereferenced before check 'hdev->req'
crypto: arm64/ghash-ce - use frame_push/pop macros consistently
crypto: arm64/crct10dif - use frame_push/pop macros consistently
crypto: arm64/aes-modes - use frame_push/pop macros consistently
...
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEg1AjqC77wbdLX2LbKSR5jcyPE6QFAmOYXUcSHHBhYmVuaUBy
ZWRoYXQuY29tAAoJECkkeY3MjxOk8zQP/R7BZtbJMTPiWkRnSoKHnAyupDVwrz5U
ktukLkwPsCyJuEbAjgxrxf4EEEQ9uq2FFlxNSYuKiiQMqIpFxV6KED7LCUygn4Tc
kxtkp0Q+5XiqisWlQmtfExf2OjuuPqcjV9tWCDBI6GebKUbfNwY/eI44RcMu4BSv
DzIlW5GkX/kZAPqnnuqaLsN3FudDTJHGEAD7NbA++7wJ076RWYSLXlFv0Z+SCSPS
H8/PEG0/ZK/65rIWMAFRClJ9BNIDwGVgp0GrsIvs1gqbRUOlA1hl1rDM21TqtNFf
5QPQT7sIfTcCE/nerxKJD5JE3JyP+XRlRn96PaRw3rt4MgI6I/EOj/HOKQ5tMCNc
oPiqb7N70+hkLZyr42qX+vN9eDPjp2koEQm7EO2Zs+/534/zWDs24Zfk/Aa1ps0I
Fa82oGjAgkBhGe/FZ6i5cYoLcyxqRqZV1Ws9XQMl72qRC7/BwvNbIW6beLpCRyeM
yYIU+0e9dEm+wHQEdh2niJuVtR63hy8tvmPx56lyh+6u0+pondkwbfSiC5aD3kAC
ikKsN5DyEsdXyiBAlytCEBxnaOjQy4RAz+3YXSiS0eBNacXp03UUrNGx4Pzpu/D0
QLFJhBnMFFCgy5to8/DvKnrTPgZdSURwqbIUcZdvU21f1HLR8tUTpaQnYffc/Whm
V8gnt1EL+0cc
=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
direction misannotations and (hopefully) preventing
more of the same for the future.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCY5ZzQAAKCRBZ7Krx/gZQ
65RZAP4nTkvOn0NZLVFkuGOx8pgJelXAvrteyAuecVL8V6CR4AD40qCVY51PJp8N
MzwiRTeqnGDxTTF7mgd//IB6hoatAA==
=bcvF
-----END PGP SIGNATURE-----
Merge tag 'pull-iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov_iter updates from Al Viro:
"iov_iter work; most of that is about getting rid of direction
misannotations and (hopefully) preventing more of the same for the
future"
* tag 'pull-iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
use less confusing names for iov_iter direction initializers
iov_iter: saner checks for attempt to copy to/from iterator
[xen] fix "direction" argument of iov_iter_kvec()
[vhost] fix 'direction' argument of iov_iter_{init,bvec}()
[target] fix iov_iter_bvec() "direction" argument
[s390] memcpy_real(): WRITE is "data source", not destination...
[s390] zcore: WRITE is "data source", not destination...
[infiniband] READ is "data destination", not source...
[fsi] WRITE is "data source", not destination...
[s390] copy_oldmem_kernel() - WRITE is "data source", not destination
csum_and_copy_to_iter(): handle ITER_DISCARD
get rid of unlikely() on page_copy_sane() calls
There are few major updates in the SoC specific drivers, mainly the usual
reworks and support for variants of the existing SoC. While this remains
Arm centric for the most part, the branch now also contains updates to
risc-v and loongarch specific code in drivers/soc/.
Notable changes include:
- Support for the newly added Qualcomm Snapdragon variants
(MSM8956, MSM8976, SM6115, SM4250, SM8150, SA8155 and SM8550) in the
soc ID, rpmh, rpm, spm and powerdomain drivers.
- Documentation for the somewhat controversial qcom,board-id
properties that are required for booting a number of machines
- A new SoC identification driver for the loongson-2 (loongarch)
platform
- memory controller updates for stm32, tegra, and renesas.
- a new DT binding to better describe LPDDR2/3/4/5 chips in
the memory controller subsystem
- Updates for Tegra specific drivers across multiple subsystems,
improving support for newer SoCs and better identification
- Minor fixes for Broadcom, Freescale, Apple, Renesas, Sifive,
TI, Mediatek and Marvell SoC drivers
-----BEGIN PGP SIGNATURE-----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=heNV
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are few major updates in the SoC specific drivers, mainly the
usual reworks and support for variants of the existing SoC. While this
remains Arm centric for the most part, the branch now also contains
updates to risc-v and loongarch specific code in drivers/soc/.
Notable changes include:
- Support for the newly added Qualcomm Snapdragon variants (MSM8956,
MSM8976, SM6115, SM4250, SM8150, SA8155 and SM8550) in the soc ID,
rpmh, rpm, spm and powerdomain drivers.
- Documentation for the somewhat controversial qcom,board-id
properties that are required for booting a number of machines
- A new SoC identification driver for the loongson-2 (loongarch)
platform
- memory controller updates for stm32, tegra, and renesas.
- a new DT binding to better describe LPDDR2/3/4/5 chips in the
memory controller subsystem
- Updates for Tegra specific drivers across multiple subsystems,
improving support for newer SoCs and better identification
- Minor fixes for Broadcom, Freescale, Apple, Renesas, Sifive, TI,
Mediatek and Marvell SoC drivers"
* tag 'soc-drivers-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (137 commits)
soc: qcom: socinfo: Add SM6115 / SM4250 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for SM6115 / SM4250 and variants
soc: qcom: socinfo: Add SM8150 and SA8155 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for SM8150 and SA8155
dt-bindings: soc: qcom: apr: document generic qcom,apr compatible
soc: qcom: Select REMAP_MMIO for ICC_BWMON driver
soc: qcom: Select REMAP_MMIO for LLCC driver
soc: qcom: rpmpd: Add SM4250 support
dt-bindings: power: rpmpd: Add SM4250 support
dt-bindings: soc: qcom: aoss: Add compatible for SM8550
soc: qcom: llcc: Add configuration data for SM8550
dt-bindings: arm: msm: Add LLCC compatible for SM8550
soc: qcom: llcc: Add v4.1 HW version support
soc: qcom: socinfo: Add SM8550 ID
soc: qcom: rpmh-rsc: Avoid unnecessary checks on irq-done response
soc: qcom: rpmh-rsc: Add support for RSC v3 register offsets
soc: qcom: rpmhpd: Add SM8550 power domains
dt-bindings: power: rpmpd: Add SM8550 to rpmpd binding
soc: qcom: socinfo: Add MSM8956/76 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for MSM8956 and MSM8976
...
-----BEGIN PGP SIGNATURE-----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=1PTZ
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Add NMI-safe SRCU reader API. It uses atomic_inc() instead of
this_cpu_inc() on strong load-store architectures.
- Introduce new console_list_lock to synchronize a manipulation of the
list of registered consoles and their flags.
This is a first step in removing the big-kernel-lock-like behavior of
console_lock(). This semaphore still serializes console->write()
calbacks against:
- each other. It primary prevents potential races between early
and proper console drivers using the same device.
- suspend()/resume() callbacks and init() operations in some
drivers.
- various other operations in the tty/vt and framebufer
susbsystems. It is likely that console_lock() serializes even
operations that are not directly conflicting with the
console->write() callbacks here. This is the most complicated
big-kernel-lock aspect of the console_lock() that will be hard
to untangle.
- Introduce new console_srcu lock that is used to safely iterate and
access the registered console drivers under SRCU read lock.
This is a prerequisite for introducing atomic console drivers and
console kthreads. It will reduce the complexity of serialization
against normal consoles and console_lock(). Also it should remove the
risk of deadlock during critical situations, like Oops or panic, when
only atomic consoles are registered.
- Check whether the console is registered instead of enabled on many
locations. It was a historical leftover.
- Cleanly force a preferred console in xenfb code instead of a dirty
hack.
- A lot of code and comment clean ups and improvements.
* tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (47 commits)
printk: htmldocs: add missing description
tty: serial: sh-sci: use setup() callback for early console
printk: relieve console_lock of list synchronization duties
tty: serial: kgdboc: use console_list_lock to trap exit
tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()
tty: serial: kgdboc: use console_list_lock for list traversal
tty: serial: kgdboc: use srcu console list iterator
proc: consoles: use console_list_lock for list iteration
tty: tty_io: use console_list_lock for list synchronization
printk, xen: fbfront: create/use safe function for forcing preferred
netconsole: avoid CON_ENABLED misuse to track registration
usb: early: xhci-dbc: use console_is_registered()
tty: serial: xilinx_uartps: use console_is_registered()
tty: serial: samsung_tty: use console_is_registered()
tty: serial: pic32_uart: use console_is_registered()
tty: serial: earlycon: use console_is_registered()
tty: hvc: use console_is_registered()
efi: earlycon: use console_is_registered()
tty: nfcon: use console_is_registered()
serial_core: replace uart_console_enabled() with uart_console_registered()
...
usb_cache_string() can also be useful for the drivers so export it.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/20221130174658.29282-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the specification documents for the Uncompressed and MJPEG USB
Video Payloads, the field name is bmInterlaceFlags - it has been
misnamed within the kernel.
Although renaming the field does break the kernel's interface to
userspace it should be low-risk in this instance. The field is read
only and hardcoded to 0, so there was never any value in anyone
reading it. A search of the uvc-gadget application and all the
forks that I could find for it did not reveal any users either.
Fixes: cdda479f15 ("USB gadget: video class function driver")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20221206161203.1562827-1-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY power is handled for peripheral mode but only when the device is
forced into this peripheral mode. It is missing when the device is
operating in peripheral mode when dual-role mode is enabled, so let's
update the condition to match this scenario.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPM feature of DWC2 module integrated in Rockchip SoCs doesn't work
properly or needs some additional handling, so disable it for now.
Without disabling LPM feature, the USB ADB communication fail with
the following error log:
dwc2 ff580000.usb: new address 27
dwc2 ff580000.usb: Failed to exit L1 sleep state in 200us.
dwc2 ff580000.usb: dwc2_hsotg_send_reply: cannot queue req
dwc2 ff580000.usb: dwc2_hsotg_process_req_status: failed to send reply
dwc2 ff580000.usb: dwc2_hsotg_enqueue_setup: failed queue (-11)
dwc2 ff580000.usb: Failed to exit L1 sleep state in 200us.
[diff vs vendor kernel: added lpm_clock_gating, besl and
hird_threshold_en settings as seen in commit 53febc9569 ("usb: dwc2:
disable Link Power Management on STM32MP15 HS OTG")]
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-1-36515e1092cd@theobroma-systems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0f01017191 ("usb: dwc3: Don't switch OTG -> peripheral
if extcon is present"), Dual Role support on Intel Merrifield platform
broke due to rearranging the call to dwc3_get_extcon().
It appears to be caused by ulpi_read_id() masking the timeout on the first
test write. In the past dwc3 probe continued by calling dwc3_core_soft_reset()
followed by dwc3_get_extcon() which happend to return -EPROBE_DEFER.
On deferred probe ulpi_read_id() finally succeeded. Due to above mentioned
rearranging -EPROBE_DEFER is not returned and probe completes without phy.
On Intel Merrifield the timeout on the first test write issue is reproducible
but it is difficult to find the root cause. Using a mainline kernel and
rootfs with buildroot ulpi_read_id() succeeds. As soon as adding
ftrace / bootconfig to find out why, ulpi_read_id() fails and we can't
analyze the flow. Using another rootfs ulpi_read_id() fails even without
adding ftrace. We suspect the issue is some kind of timing / race, but
merely retrying ulpi_read_id() does not resolve the issue.
As we now changed ulpi_read_id() to return -ETIMEDOUT in this case, we
need to handle the error by calling dwc3_core_soft_reset() and request
-EPROBE_DEFER. On deferred probe ulpi_read_id() is retried and succeeds.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221205201527.13525-3-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0f01017191 ("usb: dwc3: Don't switch OTG -> peripheral
if extcon is present") Dual Role support on Intel Merrifield platform
broke due to rearranging the call to dwc3_get_extcon().
It appears to be caused by ulpi_read_id() on the first test write failing
with -ETIMEDOUT. Currently ulpi_read_id() expects to discover the phy via
DT when the test write fails and returns 0 in that case, even if DT does not
provide the phy. As a result usb probe completes without phy.
Make ulpi_read_id() return -ETIMEDOUT to its user if the first test write
fails. The user should then handle it appropriately. A follow up patch
will make dwc3_core_init() set -EPROBE_DEFER in this case and bail out.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Link: https://lore.kernel.org/r/20221205201527.13525-2-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Genesys Logic GL850G is a 4-port USB 2.0 STT hub that has a reset pin to
toggle and a 3.3V core supply exported (although an integrated LDO is
available for powering it with 5V).
Add the support for this hub, for controlling the reset pin and the core
power supply.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20221206055228.306074-4-uwu@icenowy.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fotg210_udc_probe(), if devm_clk_get() or clk_prepare_enable()
fails, 'fotg210' will not be freed, which will lead to a memory leak.
Fix it by moving kfree() to a proper location.
In addition，we can use "return -ENOMEM" instead of "goto err"
to simplify the code.
Fixes: 718a38d092 ("fotg210-udc: Handle PCLK")
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20221202012126.246953-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Forward the mode of operation to the typec subsystem such that it can
configure the mux correctly.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20221128162304.80125-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221125170444.36620123@endymion.delvare
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The checks for musb->xceiv and musb->xceiv->set_power duplicate those in
usb_phy_set_power(), so there is no need of them. Moreover, not calling
usb_phy_set_power() results in usb_phy_set_charger_current() not being
called, so current USB config max current is not propagated through USB
charger framework and charger drivers may try to draw more current than
allowed or possible.
Fix that by removing those extra checks and calling usb_phy_set_power()
directly.
Tested on Motorola Droid4 and Nokia N900
Fixes: a9081a008f ("usb: phy: Add USB charger support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Link: https://lore.kernel.org/r/1669400475-4762-1-git-send-email-ivo.g.dimitrov.75@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setup function uvc_function_setup permits control transfer
requests with up to 64 bytes of payload (UVC_MAX_REQUEST_SIZE),
data stage handler for OUT transfer uses memcpy to copy req->actual
bytes to uvc_event->data.data array of size 60. This may result
in an overflow of 4 bytes.
Fixes: cdda479f15 ("USB gadget: video class function driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20221206141301.51305-1-szymon.heidrich@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_icc_get() alloc resources for path handle, we should release it when not
need anymore. Like the release in dwc3_qcom_interconnect_exit() function.
Add icc_put() in error handling to fix this.
Fixes: bea46b9815 ("usb: dwc3: qcom: Add interconnect support in dwc3 driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20221206081731.818107-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got the following report while doing fault injection test:
OF: ERROR: memory leak, expected refcount 1 instead of 4,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/tcpc@60/connector
If wusb3801_hw_init() fails, fwnode_handle_put() needs be called to
avoid refcount leak.
Fixes: d016cbe4d7 ("usb: typec: Support the WUSB3801 port controller")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221203071027.3808308-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As kcalloc may return NULL pointer, the return value should
be checked and return error if fails as same as the ones in
alauda_read_map.
Fixes: e80b0fade0 ("[PATCH] USB Storage: add alauda support")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20221208110058.12983-1-jiasheng@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 6.2-rc1, including:
- B0 hangup support for cp210x
- avoid requesting a zero DTE rate which could potentially confuse
buggy firmware in XR devices
Included are also some new device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCY5HyqgAKCRALxc3C7H1l
CJwyAP9KSTS9cERLT/qMbUiK7vevzG737Z81aOptoabmWHAFVgD/QYTMrzHgzCbp
7vxykl9TeaSH6R+8gQ4v3cBx9FYZsQo=
=Vojp
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.2-rc1
Here are the USB-serial updates for 6.2-rc1, including:
- B0 hangup support for cp210x
- avoid requesting a zero DTE rate which could potentially confuse
buggy firmware in XR devices
Included are also some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: xr: avoid requesting zero DTE rate
USB: serial: cp210x: add support for B0 hangup
USB: serial: cp210x: add Kamstrup RF sniffer PIDs
USB: serial: option: add Quectel EM05-G modem
Now, that we only do usb_register() and usb_sisusb_exit() in
module_init() and module_exit() respectivelly, we can simply use
module_usb_driver().
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221208090749.28056-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it's the only source for the sisusbvga module, there is no need for a
2-steps build.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221208090749.28056-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was marked as BROKEN since commit 862ee699fe (USB: sisusbvga: Make
console support depend on BROKEN) 2 years ago. Since noone stepped up to
fix it, remove it completely.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221208090749.28056-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 84582f9ed0 ("soc: fsl: qe: Avoid using gpio_to_desc()") changed
qe_pin_request() to request and hold GPIO corresponding to a given pin.
Unfortunately this does not work, as fhci-hcd requests these GPIOs
first, befor calling qe_pin_request() (see
drivers/usb/host/fhci-hcd.c::of_fhci_probe()).
To fix it change qe_pin_request() to request GPIOs non-exclusively, and
free them once the code determines GPIO controller and offset for each
GPIO/pin.
Also reaching deep into gpiolib implementation is not the best idea. We
should either export gpio_chip_hwgpio() or keep converting to the global
gpio numbers space until we fix the driver to implement proper pin
control.
Fixes: 84582f9ed0 ("soc: fsl: qe: Avoid using gpio_to_desc()")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/Y400YXnWBdz1e/L5@google.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here are two fixes for a division-by-zero issue in the Fintek drivers.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCY4o6DgAKCRALxc3C7H1l
CCyHAP9lHJ4myiSTwFlVMrSHMOGI0xGi59uUfyfx6koQWwJDawEA6C4gMYw770LA
IGiUEKcXfiDLt21bIQ8Aq9KsHxJ3wAQ=
=XU8Z
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.1-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for 6.1-rc8
Here are two fixes for a division-by-zero issue in the Fintek drivers.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.1-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: f81534: fix division by zero on line-speed change
USB: serial: f81232: fix division by zero on line-speed change
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-31-john.ogness@linutronix.de
When the requested line speed is B0 (hangup) there is no need to use the
current speed in the line-coding request. This specifically avoids
requesting a zero DTE rate when the current speed is B0, which could
potentially confuse buggy firmware.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
Fixes: 3aacac02f3 ("USB: serial: f81534: add high baud rate support")
Cc: stable@vger.kernel.org # 4.16
Cc: Ji-Ze Hong (Peter Hong) <hpeter@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
Fixes: 268ddb5e9b ("USB: serial: f81232: add high baud rate support")
Cc: stable@vger.kernel.org # 5.2
Cc: Ji-Ze Hong (Peter Hong) <hpeter@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to also limit the amount of soft reset retries for transaction
errors on streams in cases where the transaction error event doesn't point
to any specific TRB.
In these cases we don't know the TRB or stream ring, but we do know which
endpoint had the error.
To keep error counting simple and functional, move the current err_count
from ring structure to endpoint structure.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable U3 suspended ports in hibernate S4 poweroff_late for systems
with XHCI_RESET_TO_DEFAULT quirk, if wakeup is not enabled.
This reduces the number of self-powered usb devices from surviving in
U3 suspended state into next reboot.
Bootloader/firmware on these systems can't handle usb ports in U3, and
will timeout, causing extra delay during reboot/restore from S4.
Add pci_poweroff_late() callback to struct usb_hcd to get this done at
the correct stage in hibernate.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
some Intel Alder Lake xHC hosts on ChromeOS platforms need special
workarounds touching port registers at xHC pci host hibernate.
Export xhci_port_state_to_neutral() and xhci_find_slot_id_by_port()
so they can be called from xhci-pci.c and thus the xhci-pci module.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ADL-N systems have the same issue as ADL-P, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to ADL-N as well.
This patch depends on commit 34cd2db408 ("xhci: Add quirk to reset
host back to default state at shutdown").
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects ADL-N devices, and ADL-N support was added starting from v5.16.
Cc: stable@vger.kernel.org
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HCE(Host Controller Error) is set, it means that the xhci hardware
controller has an error at this time, but the current xhci driver
software does not log this event.
By adding an HCE event detection in the xhci interrupt processing
interface, a warning log is output to the system, which is convenient
for system device status tracking.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A request to set the line speed to B0 is used to hang up a modem
connection by deasserting the modem control lines.
Note that there is no need reconfigure the line speed in hardware when
B0 is requested (even if some drivers do set it to an arbitrary value
for implementation or protocol reasons).
Reviewed-by: Alex Henrie <alexh@vpitech.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
dwc->desired_dr_role is changed by dwc3_set_mode inside a spinlock but
then read by __dwc3_set_mode outside of that lock. This can lead to a
race condition when very quick successive role switch events happen:
CPU A
dwc3_set_mode(DWC3_GCTL_PRTCAP_HOST) // first role switch event
spin_lock_irqsave(&dwc->lock, flags);
dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_HOST
spin_unlock_irqrestore(&dwc->lock, flags);
queue_work(system_freezable_wq, &dwc->drd_work);
CPU B
__dwc3_set_mode
// ....
spin_lock_irqsave(&dwc->lock, flags);
// desired_dr_role is DWC3_GCTL_PRTCAP_HOST
dwc3_set_prtcap(dwc, dwc->desired_dr_role);
spin_unlock_irqrestore(&dwc->lock, flags);
CPU A
dwc3_set_mode(DWC3_GCTL_PRTCAP_DEVICE) // second event
spin_lock_irqsave(&dwc->lock, flags);
dwc->desired_dr_role = mode; // DWC3_GCTL_PRTCAP_DEVICE
spin_unlock_irqrestore(&dwc->lock, flags);
CPU B (continues running __dwc3_set_mode)
switch (dwc->desired_dr_role) { // DWC3_GCTL_PRTCAP_DEVICE
// ....
case DWC3_GCTL_PRTCAP_DEVICE:
// ....
ret = dwc3_gadget_init(dwc);
We then have DWC3_GCTL.DWC3_GCTL_PRTCAPDIR = DWC3_GCTL_PRTCAP_HOST and
dwc->current_dr_role = DWC3_GCTL_PRTCAP_HOST but initialized the
controller in device mode. It's also possible to get into a state
where both host and device are intialized at the same time.
Fix this race by creating a local copy of desired_dr_role inside
__dwc3_set_mode while holding dwc->lock.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20221128161526.79730-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list API now provides the list_count() to help with counting
existing nodes in the list. Utilise it.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221123144901.40493-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify error handling at the end of the function, reducing the risk of
missing something on one of the error paths.
Moving the increment of opts->refcnt later means there is no need to
decrement it on the error path and is safe as this is guarded by
opts->lock which is held for this entire section.
Tested-by: Lee Jones <lee@kernel.org>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20221122123523.3068034-4-john@metanate.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When failing to allocate report_desc, opts->refcnt has already been
incremented so it needs to be decremented to avoid leaving the options
structure permanently locked.
Fixes: 21a9476a7b ("usb: gadget: hid: add configfs support")
Tested-by: Lee Jones <lee@kernel.org>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20221122123523.3068034-3-john@metanate.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The embedded struct cdev does not have its lifetime correctly tied to
the enclosing struct f_hidg, so there is a use-after-free if /dev/hidgN
is held open while the gadget is deleted.
This can readily be replicated with libusbgx's example programs (for
conciseness - operating directly via configfs is equivalent):
gadget-hid
exec 3<> /dev/hidg0
gadget-vid-pid-remove
exec 3<&-
Pull the existing device up in to struct f_hidg and make use of the
cdev_device_{add,del}() helpers. This changes the lifetime of the
device object to match struct f_hidg, but note that it is still added
and deleted at the same time.
Fixes: 71adf11894 ("USB: gadget: add HID gadget driver")
Tested-by: Lee Jones <lee@kernel.org>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20221122123523.3068034-2-john@metanate.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221127155230.144886b7@endymion.delvare
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch implements the handling of ZLP for control transfer.
To send the ZLP driver must prepare the extra TRB in TD with
length set to zero and TRB type to TRB_NORMAL.
The first TRB must have set TRB_CHAIN flag, TD_SIZE = 1
and TRB type to TRB_DATA.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20221122085138.332434-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The am35x glue layer is no longer in use and can be dropped. There are no
longer any SoCs passing platform data for it as they are booting using
devicetree.
In general, the am35x SoCs are similar to am335x and ti81xx and can
use the musb_dsps glue layer as long as there is a proper phy driver
available.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221125085506.38127-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some port drivers may want to set a Type-C partner as a parent for a
USB Power Delivery object, but the Type-C partner struct isn't exposed
outside of the Type-C class driver. Add a wrapper to
usb_power_delivery_register() which sets the provided Type-C partner
as a parent to the USB PD object. This helps to avoid exposing the
Type-C partner's device struct unnecessarily.
Cc: Benson Leung <bleung@chromium.org>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20221122220538.2991775-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Can not set the @shared_hcd to NULL before decrease the usage count
by usb_put_hcd(), this will cause the shared hcd not released.
Fixes: 04284eb74e ("usb: xhci-mtk: add support runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20221128063337.18124-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers do not need to call usb_set_intfdata(intf, NULL) in their
usb_driver::disconnect callback because the core already does it in [1].
However, this fact is widely unknown, c.f.:
$ git grep "usb_set_intfdata(.*NULL)" | wc -l
215
Especially, setting the interface to NULL before all action completed
can result in a NULL pointer dereference. Not calling
usb_set_intfdata() at all in disconnect() is the safest method.
Add documentation to usb_set_intfdata() to clarify this point.
Also remove the call in usb-skeletion's disconnect() not to confuse
the new comers.
[1] function usb_unbind_interface() from drivers/usb/core/driver.c
Link: https://elixir.bootlin.com/linux/v6.0/source/drivers/usb/core/driver.c#L497
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20221128102954.3615579-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device ID 0xa70e is defined for the USB3 device controller in the CPU
sub-system of Raptor Lake platform. Hence updating the ID accordingly.
Fixes: bad0d1d726 ("usb: dwc3: pci: Add support for Intel Raptor Lake")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20221125105327.27945-1-shruthi.sanil@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dmam_alloc_attrs() fails, it returns NULL pointer and never
return ERR_PTR(), so repleace IS_ERR() with IS_ERR_OR_NULL()
and if it's NULL, returns -ENOMEM.
Fixes: 9ba26f5cec ("ARM: sa1100/assabet: move dmabounce hack to ohci driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221125064120.2842452-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't issue messages which can be easily achieved with ftrace.
In case of printer_open() the return code is propagated to other layers
so the user will know about -EBUSY anyway.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/20221123110746.59611-1-andrzej.p@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can take more than one second to check each connector
when the system is resumed. So if you have, say, eight
connectors, it may take eight seconds for ucsi_resume() to
finish. That's a bit too much.
This will modify ucsi_resume() so that it schedules a work
where the interface is actually resumed instead of checking
the connectors directly. The connections will also be
checked in separate tasks which are queued for each connector
separately.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216706
Fixes: 99f6d43611 ("usb: typec: ucsi: Check the connection on resume")
Cc: <stable@vger.kernel.org>
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221123093021.25981-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got the following report while doing device(mt6370-tcpc) load
test with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@34
The 'parent' returned by fwnode_get_parent() with refcount incremented.
it needs be put after using.
Fixes: 6fadd72943 ("usb: roles: get usb-role-switch from parent")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221122111226.251588-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RF sniffers are based on cp210x where the RF frontends
are based on a different USB stack.
RF sniffers can analyze packets meta data including power level
and perform packet injection.
Can be used to perform RF frontend self-test when connected to
a concentrator, ex. arch/arm/boot/dts/imx7d-flex-concentrator.dts
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
READ/WRITE proved to be actively confusing - the meanings are
"data destination, as used with read(2)" and "data source, as
used with write(2)", but people keep interpreting those as
"we read data from it" and "we write data to it", i.e. exactly
the wrong way.
Call them ITER_DEST and ITER_SOURCE - at least that is harder
to misinterpret...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The devnode() in struct class should not be modifying the device that is
passed into it, so mark it as a const * and propagate the function
signature changes out into all relevant subsystems that use this
callback.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Justin Sanders <justin@coraid.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Cc: Liam Mark <lmark@codeaurora.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Cc: John Stultz <jstultz@google.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Sean Young <sean@mess.org>
Cc: Frank Haverkamp <haver@linux.ibm.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Xie Yongji <xieyongji@bytedance.com>
Cc: Gautam Dawar <gautam.dawar@xilinx.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Eli Cohen <elic@nvidia.com>
Cc: Parav Pandit <parav@nvidia.com>
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Cc: alsa-devel@alsa-project.org
Cc: dri-devel@lists.freedesktop.org
Cc: kvm@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-block@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Link: https://lore.kernel.org/r/20221123122523.1332370-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_uevent() in struct class should not be modifying the device that
is passed into it, so mark it as a const * and propagate the function
signature changes out into all relevant subsystems that use this
callback.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Raed Salem <raeds@nvidia.com>
Cc: Chen Zhongjin <chenzhongjin@huawei.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Avihai Horon <avihaih@nvidia.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Colin Ian King <colin.i.king@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jakob Koschel <jakobkoschel@gmail.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Wang Yufen <wangyufen@huawei.com>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: linux-pm@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20221123122523.1332370-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20221118224540.619276-573-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-574-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-575-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-576-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-577-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-578-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-579-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221118224540.619276-580-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-581-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-582-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221118224540.619276-583-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-584-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-585-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the process of switching USB config from rndis to other config,
if the hardware does not support the ->pullup callback, or the
hardware encounters a low probability fault, both of them may cause
the ->pullup callback to fail, which will then cause a system panic
(use after free).
The gadget drivers sometimes need to be unloaded regardless of the
hardware's behavior.
Analysis as follows:
=======================================================================
(1) write /config/usb_gadget/g1/UDC "none"
gether_disconnect+0x2c/0x1f8
rndis_disable+0x4c/0x74
composite_disconnect+0x74/0xb0
configfs_composite_disconnect+0x60/0x7c
usb_gadget_disconnect+0x70/0x124
usb_gadget_unregister_driver+0xc8/0x1d8
gadget_dev_desc_UDC_store+0xec/0x1e4
(2) rm /config/usb_gadget/g1/configs/b.1/f1
rndis_deregister+0x28/0x54
rndis_free+0x44/0x7c
usb_put_function+0x14/0x1c
config_usb_cfg_unlink+0xc4/0xe0
configfs_unlink+0x124/0x1c8
vfs_unlink+0x114/0x1dc
(3) rmdir /config/usb_gadget/g1/functions/rndis.gs4
panic+0x1fc/0x3d0
do_page_fault+0xa8/0x46c
do_mem_abort+0x3c/0xac
el1_sync_handler+0x40/0x78
0xffffff801138f880
rndis_close+0x28/0x34
eth_stop+0x74/0x110
dev_close_many+0x48/0x194
rollback_registered_many+0x118/0x814
unregister_netdev+0x20/0x30
gether_cleanup+0x1c/0x38
rndis_attr_release+0xc/0x14
kref_put+0x74/0xb8
configfs_rmdir+0x314/0x374
If gadget->ops->pullup() return an error, function rndis_close() will be
called, then it will causes a use-after-free problem.
=======================================================================
Fixes: 0a55187a1e ("USB: gadget core: Issue ->disconnect() callback from usb_gadget_disconnect()")
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: TaoXue <xuetao09@huawei.com>
Link: https://lore.kernel.org/r/20221121130805.10735-1-water.zhangjiantao@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A request to Manish Narani (see Link) asked for clarification of the
reference to the config ARCH_VERSAL in the support of Xilinx SoCs with
DesignWare Core USB3 IP.
As there is no response, clean up the reference to the non-existing config
symbol. While at it, follow up on Felipe Balbi's request to add the
alternative COMPILE_TEST dependency.
Link: https://lore.kernel.org/all/CAKXUXMwgWfX8+OvY0aCwRNukencwJERAZzU7p4eOLXQ2zv6rAg@mail.gmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221116110444.8340-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Probe for omap2430 glue layer is now broken for interrupt resources in
all cases.
Commit 2390710647 ("partially Revert "usb: musb: Set the DT node on the
child device"") broke probing for SoCs using ti-sysc interconnect target
module as the dt node is not found.
Commit a1a2b7125e ("of/platform: Drop static setup of IRQ resource from
DT core") caused omap3 to fail with error "-ENXIO: IRQ mc not found" as
the IRQ resources are no longer automatically populated from devicetree.
Let's fix the issues by calling device_set_of_node_from_dev() only if the
SoC has been updated to probe with ti-sysc. And for legacy SoCs, let's
populate the resources manually as needed.
Note that once we have updated the SoCs to probe with proper devicetree
data in all cases, this is no longer needed. But doing that requires
patching both devicetree and SoC code, so let's fix the probe issues first.
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Fixes: 2390710647 ("partially Revert "usb: musb: Set the DT node on the child device"")
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Reported-by: Sicelo Mhlongo <absicsz@gmail.com>
Tested-by: Sicelo Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221118102532.34458-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the code currently correctly calls tps6598x_disconnect before jumping
to the error cleanup label it's inconsistent compared to all the other cleanup
actions and prone to introduce bugs if any more resources are added.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-4-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
typec_unregister_port is only called for some error paths after
typec_register_port was successful. Ensure it's called in all
cases.
Fixes: 92440202a8 ("usb: typec: tipd: Only update power status on IRQ")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-3-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The err_role_put error path always calls fwnode_handle_put to release
the fwnode. This path can be reached after probe itself has already
released that fwnode though. Fix that by moving fwnode_handle_put in the
happy path to the very end.
Fixes: 18a6c866bb ("usb: typec: tps6598x: Add USB role switching logic")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-2-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't just return if devm_tps6598_psy_register fails since previous
resources are not devres managed and have yet to be cleaned up.
Fixes: 10eb0b6ac6 ("usb: typec: tps6598x: Export some power supply properties")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114174449.34634-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is error log when add a usb3 root hub without ports:
"hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)"
so omit the shared hcd if either of the root hubs has no ports, but
usually there is no usb3 port.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221118110116.20165-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got the following report while doing device(mt6370-tcpc) load
test with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@34/tcpc/connector
The 'fwnode' set in tcpci_parse_config() which is called
in tcpci_register_port(), its node refcount is increased
in device_get_named_child_node(). It needs be put while
exiting, so call fwnode_handle_put() in the error path of
tcpci_register_port() and in tcpci_unregister_port() to
avoid leak.
Fixes: 5e85a04c8c ("usb: typec: add fwnode to tcpc")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221121062416.1026192-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
typec_altmode_exit checks if ops->enter is not NULL but then calls
ops->exit a few lines below. Fix that and check for the function
pointer it's about to call instead.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221114165924.33487-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable l is just being accumulated and it's never used
anywhere else. The variable and the addition are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221111165724.557152-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to use an intermediate array for these memory allocations,
so, axe it.
While at it, turn a '== NULL' into a shorter '!' when testing memory
allocation failure.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/deab9696fc4000499470e7ccbca7c36fca17bd4e.1668458274.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_get_irq() is necessary to use to get dynamic
IRQ resolution when instantiating the device from the
device tree. IRQs are not passed as resources in that
case.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221114115201.302887-4-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for an optional external PHY to the FOTG210
UDC driver.
Tested with the GPIO VBUS PHY driver on the Gemini SoC.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221114115201.302887-2-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Faraday Technology FOTG210 USB2 Dual Role Controller is only present
on Cortina Systems Gemini SoCs. Hence add a dependency on ARCH_GEMINI,
to prevent asking the user about its drivers when configuring a kernel
without Cortina Systems Gemini SoC support.
Fixes: 1dd33a9f1b ("usb: fotg210: Collect pieces of dual mode controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/a989b3b798ecaf3b45f35160e30e605636d66a77.1669044086.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel robot reports a link failure when activating the
FOTG210 host subdriver with =y on a system where the USB host
core is a module (CONFIG_USB=m).
This is a bit of special case, so mimic the Kconfig incantations
from DWC3: let the subdrivers for host or peripheral depend
on the host or gadget support being =y or the same as the
FOTG210 core itself.
This should ensure that either:
- The host (CONFIG_USB) or gadget (CONFIG_GADGET) is compiled
in and then the FOTG210 can be either module or compiled
in.
- The host or gadget is modular, and then the FOTG210 module
must be a module too, or we cannot resolve the symbols
at link time.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-usb/202211112132.0BUPGKCd-lkp@intel.com/
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221111144821.113665-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch modifies the TD_SIZE in TRB before ZLP TRB.
The TD_SIZE in TRB before ZLP TRB must be set to 1 to force
processing ZLP TRB by controller.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20221115092218.421267-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until the endpoint is disabled, its descriptors should remain valid.
When its requests are removed from ep disable, the request completion
routine may attempt to access the endpoint's descriptor. Don't clear the
descriptors before that.
Fixes: f09ddcfcb8 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/45db7c83b209259115bf652af210f8b2b3b1a383.1668561364.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core DWC3 device node was not properly removed by the custom
dwc3_exynos_remove_child() function. Replace it with generic
of_platform_depopulate() which does that job right.
Fixes: adcf20dcd2 ("usb: dwc3: exynos: Use of_platform API to create dwc3 core pdev")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20221110154131.2577-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During handling Clear Halt Endpoint Feature request, driver invokes
Reset Endpoint command. Because this command has some issue with
transition endpoint from Running to Idle state the driver must
stop the endpoint by using Stop Endpoint command.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20221110063005.370656-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since e219a712bc (usb: gadget: uvc: add v4l2 try_format api call) the
try_format function is available. With this function includes checks for
valid configurations programmed in the configfs. We use this function to
ensure to return valid values on the set_format callback.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Fixes: e219a712bc ("usb: gadget: uvc: add v4l2 try_format api call")
Link: https://lore.kernel.org/r/20221026182240.363055-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most hw_random devices return entropy which is assumed to be of full
quality, but driver authors don't bother setting the quality knob. Some
hw_random devices return less than full quality entropy, and then driver
authors set the quality knob. Therefore, the entropy crediting should be
opt-out rather than opt-in per-driver, to reflect the actual reality on
the ground.
For example, the two Raspberry Pi RNG drivers produce full entropy
randomness, and both EDK2 and U-Boot's drivers for these treat them as
such. The result is that EFI then uses these numbers and passes the to
Linux, and Linux credits them as boot, thereby initializing the RNG.
Yet, in Linux, the quality knob was never set to anything, and so on the
chance that Linux is booted without EFI, nothing is ever credited.
That's annoying.
The same pattern appears to repeat itself throughout various drivers. In
fact, very very few drivers have bothered setting quality=1024.
Looking at the git history of existing drivers and corresponding mailing
list discussion, this conclusion tracks. There's been a decent amount of
discussion about drivers that set quality < 1024 -- somebody read and
interepreted a datasheet, or made some back of the envelope calculation
somehow. But there's been very little, if any, discussion about most
drivers where the quality is just set to 1024 or unset (or set to 1000
when the authors misunderstood the API and assumed it was base-10 rather
than base-2); in both cases the intent was fairly clear of, "this is a
hardware random device; it's fine."
So let's invert this logic. A hw_random struct's quality knob now
controls the maximum quality a driver can produce, or 0 to specify 1024.
Then, the module-wide switch called "default_quality" is changed to
represent the maximum quality of any driver. By default it's 1024, and
the quality of any particular driver is then given by:
min(default_quality, rng->quality ?: 1024);
This way, the user can still turn this off for weird reasons (and we can
replace whatever driver-specific disabling hacks existed in the past),
yet we get proper crediting for relevant RNGs.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Here are some new modem device ids for 6.1.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCY3YdbAAKCRALxc3C7H1l
CG7TAQCAET51PBuwY6sxj0Fc2JvvdsY7iF7gOXO2x4dzoKbTGwEA9V3CTQFcJAwF
Iapf67+p42TdUePhJHwT+V4Ii+Bwdww=
=R8+X
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.1-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
"USB-serial fixes for 6.1-rc6
Here are some new modem device ids for 6.1.
All have been in linux-next with no reported issues."
* tag 'usb-serial-6.1-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add u-blox LARA-L6 modem
USB: serial: option: add u-blox LARA-R6 00B modem
USB: serial: option: remove old LARA-R6 PID
USB: serial: option: add Fibocom FM160 0x0111 composition
USB: serial: option: add Sierra Wireless EM9191
Add LARA-L6 PIDs for three different USB compositions.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
[ johan: drop PID defines in favour of comments ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.
LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove the UBLOX_PRODUCT_R6XX 0x90fa association since LARA-R6 00B final
product uses a new USB composition with different PID. 0x90fa PID used
only by LARA-R6 internal prototypes.
Move 0x90fa PID directly in the option_ids array since used by other
Qualcomm based modem vendors as pointed out in:
https://lore.kernel.org/all/6572c4e6-d8bc-b8d3-4396-d879e4e76338@gmail.com
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix v_recv_cmd_submit() to use PIPE_BULK define instead of hard coded
values. This also fixes the following signed integer overflow error
reported by cppcheck. This is not an issue since pipe is unsigned int.
However, this change improves the code to use proper define.
drivers/usb/usbip/vudc_rx.c:152:26: error: Signed integer overflow for expression '3<<30'. [integerOverflow]
urb_p->urb->pipe &= ~(3 << 30);
In addition, add a build time check for PIPE_BULK != 3 as the code path
depends on PIPE_BULK = 3.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20221110194738.38514-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NO_IRQ is a relic from the old days. It is not used anymore in core
functions. By the way, function irq_of_parse_and_map() returns value 0
on error.
In some drivers, NO_IRQ is erroneously used to check the return of
irq_of_parse_and_map().
It is not a real bug today because the only architectures using the
drivers being fixed by this patch define NO_IRQ as 0, but there are
architectures which define NO_IRQ as -1. If one day those
architectures start using the non fixed drivers, there will be a
problem.
Long time ago Linus advocated for not using NO_IRQ, see
https://lkml.org/lkml/2005/11/21/221 . He re-iterated the same view
recently in https://lkml.org/lkml/2022/10/12/622
So test !irq instead of tesing irq == NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/13feefdf6b240817944e6441e26a8ddc1d81ced1.1668102802.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in the FOTG210 driver isn't entirely endianness-agnostic
as reported by the kernel robot sparse testing. This came to
the surface while moving the files around.
The driver is only used on little-endian systems, so this causes
no real-world regression, but it is nice to be strict and have
some compile coverage also on big endian machines, so fix it
up with the right LE accessors.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-usb/202211110910.0dJ7nZCn-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221111090317.94228-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cortina Systems Gemini has bolted on a PHY inside the
silicon that can be handled by six bits in a MISC register in
the system controller.
If we are running on Gemini, look up a syscon regmap through
a phandle and enable VBUS and optionally the Mini-B connector.
If the device is flagged as "wakeup-source" using the standard
DT bindings, we also enable this in the global controller for
respective port.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221109200554.1957185-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before adding this quirk, this (mechanical keyboard) device would not be
recognized, logging:
new full-speed USB device number 56 using xhci_hcd
unable to read config index 0 descriptor/start: -32
chopping to 0 config(s)
It would take dozens of plugging/unpuggling cycles for the keyboard to
be recognized. Keyboard seems to simply work after applying this quirk.
This issue had been reported by users in two places already ([1], [2])
but nobody tried upstreaming a patch yet. After testing I believe their
suggested fix (DELAY_INIT + NO_LPM + DEVICE_QUALIFIER) was probably a
little overkill. I assume this particular combination was tested because
it had been previously suggested in [3], but only NO_LPM seems
sufficient for this device.
[1]: https://qiita.com/float168/items/fed43d540c8e2201b543
[2]: https://blog.kostic.dev/posts/making-the-realforce-87ub-work-with-usb30-on-Ubuntu/
[3]: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1678477
Cc: stable@vger.kernel.org
Signed-off-by: Nicolas Dumazet <ndumazet@google.com>
Link: https://lore.kernel.org/r/20221109122946.706036-1-ndumazet@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget may change over bind/unbind cycles, so set it each time during
bind, not only the first time. Without it we get a use-after-free with
the following example:
cd /sys/kernel/config/usb_gadget/; mkdir -p mygadget; cd mygadget
mkdir -p configs/c.1/strings/0x409
echo "C1:Composite Device" > configs/c.1/strings/0x409/configuration
mkdir -p functions/ecm.usb0
ln -s functions/ecm.usb0 configs/c.1/
rmmod dummy_hcd
modprobe dummy_hcd
KASAN will complain shortly after the 'modprobe':
usb 2-1: New USB device found, idVendor=0000, idProduct=0000, bcdDevice= 6.01
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
==================================================================
BUG: KASAN: use-after-free in gether_connect+0xb8/0x30c
Read of size 4 at addr cbef170c by task swapper/3/0
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.1.0-rc3-00014-g41ff012f50cb-dirty #322
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from print_report+0x134/0x4d4
print_report from kasan_report+0x78/0x10c
kasan_report from gether_connect+0xb8/0x30c
gether_connect from ecm_set_alt+0x124/0x254
ecm_set_alt from composite_setup+0xb98/0x2b18
composite_setup from configfs_composite_setup+0x80/0x98
configfs_composite_setup from dummy_timer+0x8f0/0x14a0 [dummy_hcd]
...
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221104131031.850850-3-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC is not a suitable parent of the net device as the UDC can
change or vanish during the lifecycle of the ethernet gadget. This
can be illustrated with the following:
mkdir -p /sys/kernel/config/usb_gadget/mygadget
cd /sys/kernel/config/usb_gadget/mygadget
mkdir -p configs/c.1/strings/0x409
echo "C1:Composite Device" > configs/c.1/strings/0x409/configuration
mkdir -p functions/ecm.usb0
ln -s functions/ecm.usb0 configs/c.1/
echo "dummy_udc.0" > UDC
rmmod dummy_hcd
The 'rmmod' removes the UDC from the just created gadget, leaving
the still existing net device with a no longer existing parent.
Accessing the ethernet device with commands like:
ip --details link show usb0
will result in a KASAN splat:
==================================================================
BUG: KASAN: use-after-free in if_nlmsg_size+0x3e8/0x528
Read of size 4 at addr c5c84754 by task ip/357
CPU: 3 PID: 357 Comm: ip Not tainted 6.1.0-rc3-00013-gd14953726b24-dirty #324
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from print_report+0x134/0x4d4
print_report from kasan_report+0x78/0x10c
kasan_report from if_nlmsg_size+0x3e8/0x528
if_nlmsg_size from rtnl_getlink+0x2b4/0x4d0
rtnl_getlink from rtnetlink_rcv_msg+0x1f4/0x674
rtnetlink_rcv_msg from netlink_rcv_skb+0xb4/0x1f8
netlink_rcv_skb from netlink_unicast+0x294/0x478
netlink_unicast from netlink_sendmsg+0x328/0x640
netlink_sendmsg from ____sys_sendmsg+0x2a4/0x3b4
____sys_sendmsg from ___sys_sendmsg+0xc8/0x12c
___sys_sendmsg from sys_sendmsg+0xa0/0x120
sys_sendmsg from ret_fast_syscall+0x0/0x1c
Solve this by not setting the parent of the ethernet device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221104131031.850850-2-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has been replaced by the Ingenic PHY driver that uses the
generic PHY framework.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-8-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support PHYs implemented using the generic PHY framework instead of the
deprecated USB-PHY framework.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-7-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The jz4740-musb driver does not really support OTG, so it has no reason
to disable external hubs, especially since it's a system-wide setting
and we don't want external hubs to be disabled for other USB host
controllers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-6-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When musb->xceiv is not provided but musb->phy is, support setting the
OTG mode (host, peripheral) using the generic PHY framework.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-5-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_otg_state_string() simply calls usb_otg_state_string().
This will make it easier to get rid of the musb->xceiv dependency later.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of manipulating musb->xceiv->otg->state directly, use the newly
introduced musb_get_state() and musb_set_state() inline functions.
Later, these inline functions will be modified to get rid of the
musb->xceiv dependency, which prevents the musb code from using the
generic PHY subsystem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check which mode the hardware is in, and selecte the peripheral
driver if the hardware is in explicit peripheral mode, otherwise
select host mode.
This should solve the immediate problem that both subdrivers
can get probed.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221023144708.3596563-3-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is since ages perfectly possible to compile both of these
modules into the same kernel, which makes no sense since it
is one piece of hardware.
Compile one module named "fotg210.ko" for both HCD and UDC
drivers by collecting the init calls into a fotg210-core.c
file and start to centralize things handling one and the same
piece of hardware.
Stub out the initcalls if one or the other part of the driver
was not selected.
Tested by compiling one or the other or both of the drivers
into the kernel and as modules.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221023144708.3596563-2-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Faraday FOTG210 is a dual-mode OTG USB controller that can
act as host, peripheral or both. To be able to probe from one
hardware description and to follow the pattern of other dual-
mode controllers such as MUSB or MTU3 we need to collect the
two, currently completely separate drivers in the same
directory.
After this, users need to select the main symbol USB_FOTG210
and then each respective subdriver. We pave the road to
compile both drivers into the same kernel and select the
one we want to use at probe() time, and possibly add OTG
support in the end.
This patch doesn't do much more than create the new symbol
and collect the drivers in one place. We also add a comment
for the section of dual-mode controllers in the Kconfig
file so people can see what these selections are about.
Also add myself as maintainer as there has been little
response on my patches to these drivers.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221023144708.3596563-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is not set, the following error will be shown up
when build kernel:
error: 'ci_handle_power_lost' defined but not used.
This will move ci_handle_power_lost() to an area wrapped by
CONFIG_PM_SLEEP.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221026121157.1491302-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ast_vhub_epn_handle_ack() when the received data length exceeds the
buffer, it does not check the case and just copies to req.buf and cause
a buffer overflow, kernel oops on this case.
This issue could be reproduced on a BMC with an OS that enables the
lan over USB:
1. In OS, enable the usb eth dev, verify it pings the BMC OK;
2. In OS, set the usb dev mtu to 2000. (Default is 1500);
3. In OS, ping the BMC with `-s 2000` argument.
The BMC kernel will get oops with below logs:
skbuff: skb_over_panic: text:8058e098 len:2048 put:2048 head:84c678a0 data:84c678c2 tail:0x84c680c2 end:0x84c67f00 dev:usb0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
Internal error: Oops - BUG: 0 [#1] ARM
CPU: 0 PID: 0 Comm: swapper Not tainted 5.15.69-c9fb275-dirty-d1e579a #1
Hardware name: Generic DT based system
PC is at skb_panic+0x60/0x6c
LR is at irq_work_queue+0x6c/0x94
Fix the issue by checking the length and set `-EOVERFLOW`.
Tested: Verify the BMC kernel does not get oops in the above case, and
the usb ethernet gets RX packets errors instead.
Signed-off-by: Lei YU <yulei.sh@bytedance.com>
Signed-off-by: Henry Tian <tianxiaofeng@bytedance.com>
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: https://lore.kernel.org/r/20221024094853.2877441-1-yulei.sh@bytedance.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver often takes on the order of 10ms to start, but in some cases
takes more than 100ms. It shouldn't have many cross-device dependencies
to race with, nor racy access to shared state with other drivers, so
this should be a relatively low risk change.
This driver was pinpointed as part of a survey of top slowest initcalls
(i.e., are built in, and probing synchronously) on a lab of ChromeOS
systems.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20221028184507.v2.2.I5a309231785d3a4e37118a25e84f5caa0136a343@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver often takes on the order of 8ms to start, but every little
bit counts. It shouldn't have many cross-device dependencies to
race with, nor racy access to shared state with other drivers, so this
should be a relatively low risk change.
This driver was pinpointed as part of a survey of top slowest initcalls
(i.e., are built in, and probing synchronously) on a lab of ChromeOS
systems.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20221028184507.v2.1.I9a5353f81d1509f85f3a04f0cdc9099f6fe60811@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb 3.0 hub connect with one USB 2.0 device and NO USB 3.0 device,
some usb hub reports endless port reset message.
[ 190.324169] usb 2-1: new SuperSpeed USB device number 88 using xhci-hcd
[ 190.352834] hub 2-1:1.0: USB hub found
[ 190.356995] hub 2-1:1.0: 4 ports detected
[ 190.700056] usb 2-1: USB disconnect, device number 88
[ 192.472139] usb 2-1: new SuperSpeed USB device number 89 using xhci-hcd
[ 192.500820] hub 2-1:1.0: USB hub found
[ 192.504977] hub 2-1:1.0: 4 ports detected
[ 192.852066] usb 2-1: USB disconnect, device number 89
The reason is the runtime pm state of USB2.0 port is active and
USB 3.0 port is suspend, so parent device is active state.
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb2/power/runtime_status
suspended
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb1/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/power/runtime_status
active
cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/power/runtime_status
active
So xhci_cdns3_suspend_quirk() have not called. U3 configure is not applied.
move U3 configure into host start. Reinit again in resume function in case
controller power lost during suspend.
Cc: stable@vger.kernel.org 5.10
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221026190749.2280367-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in ci_otg_del_timer(), the process is
shown below:
(thread 1) | (thread 2)
ci_otg_del_timer() | ci_otg_hrtimer_func()
... |
spin_lock_irqsave() //(1) | ...
... |
hrtimer_cancel() | spin_lock_irqsave() //(2)
(block forever)
We hold ci->lock in position (1) and use hrtimer_cancel() to
wait ci_otg_hrtimer_func() to stop, but ci_otg_hrtimer_func()
also need ci->lock in position (2). As a result, the
hrtimer_cancel() in ci_otg_del_timer() will be blocked forever.
This patch extracts hrtimer_cancel() from the protection of
spin_lock_irqsave() in order that the ci_otg_hrtimer_func()
could obtain the ci->lock.
What`s more, there will be no race happen. Because the
"next_timer" is always under the protection of
spin_lock_irqsave() and we only check whether "next_timer"
equals to NUM_OTG_FSM_TIMERS in the following code.
Fixes: 3a316ec4c9 ("usb: chipidea: use hrtimer for otg fsm timers")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220918033312.94348-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change breaks device tree based platforms with PHY device and use
usb-role-switch instead of an extcon switch. extcon_find_edev_by_node()
will return EPROBE_DEFER if it can not find a device so probing without
an extcon device will be deferred indefinitely. Fix this by
explicitly checking for usb-role-switch.
At least the out-of-tree USB3 support on Apple silicon based platforms
using dwc3 with tipd USB Type-C and PD controller is affected by this
issue.
Fixes: d182c2e1bc ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
Cc: stable@kernel.org
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20221106214804.2814-1-j@jannau.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If reading TPS_REG_INT_EVENT1/2 fails in the interrupt handler event1
and event2 may be uninitialized when they are used to determine
IRQ_HANDLED vs. IRQ_NONE in the error path.
Fixes: c7260e29dd ("usb: typec: tipd: Add short-circuit for no irqs")
Fixes: 45188f27b3 ("usb: typec: tipd: Add support for Apple CD321X")
Cc: stable <stable@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/20221102161542.30669-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point to enter safe mode during DP/TBT configuration
if the DP/TBT was already configured in mux. This is because safe
mode is only applicable when there is a need to reconfigure the
pins in order to avoid damage within/to port partner.
In some chrome systems, IOM/mux is already configured before OS
comes up. Thus, when driver is probed, it blindly enters safe
mode due to PD negotiations but only after gfx driver lowers
dp_phy_ownership, will the IOM complete safe mode and send an
ack to PMC.
Since, that never happens, we see IPC timeout.
Hence, allow safe mode only when pin reconfiguration is not
required, which makes sense.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable <stable@kernel.org>
Signed-off-by: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221024171611.181468-1-rajat.khandelwal@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a broken USB accessory connects to a USB host, usbcore might
keep doing enumeration retries. If the host has a watchdog mechanism,
the kernel panic will happen on the host.
This patch provides an attribute early_stop to limit the numbers of retries
for each port of a hub. If a port was marked with early_stop attribute,
unsuccessful connection attempts will fail quickly. In addition, if an
early_stop port has failed to initialize, it will ignore all future
connection events until early_stop attribute is clear.
Signed-off-by: Ray Chi <raychi@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20221107072754.3336357-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the TRB ring is full, the dwc3 driver must make sure that there's
at least 1 TRB with Interrupt On Completion (IOC) set to notify of
available TRBs.
The current logic just sets the TRB's IOC whenever we run out of TRBs,
but it doesn't consider that there may be other TRBs with IOC/LST set
already. This creates more events and unnecessary delay from interrupt
handling. Only forcefully set IOC when we run out of TRBs and none of
the TRBs in the TRB ring has had IOC set.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/72a1fa448eb1201b152e65be7902a5d1c75b9f3a.1667867687.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6000b8d900.
The offending commit disabled the USB core PHY management as the dwc3
already manages the PHYs in question.
Unfortunately some platforms have started relying on having USB core
also controlling the PHY and this is specifically currently needed on
some Exynos platforms for PHY calibration or connected device may fail
to enumerate.
The PHY calibration was previously handled in the dwc3 driver, but to
work around some issues related to how the dwc3 driver interacts with
xhci (e.g. using multiple drivers) this was moved to USB core by commits
34c7ed72f4 ("usb: core: phy: add support for PHY calibration") and
a0a465569b ("usb: dwc3: remove generic PHY calibrate() calls").
The same PHY obviously should not be controlled from two different
places, which for example do no agree on the PHY mode or power state
during suspend, but as the offending patch was backported to stable,
let's revert it for now.
Reported-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/lkml/808bdba846bb60456adf10a3016911ee@agner.ch/
Fixes: 6000b8d900 ("usb: dwc3: disable USB core PHY management")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20221103144648.14197-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
What the code does is to not check the return value from
devm_gpiod_get() and then avoid using an erroneous GPIO descriptor
with IS_ERR_OR_NULL().
This will miss real errors from the GPIO core that should not be
ignored, such as probe deferral.
Instead request the GPIO as explicitly optional, which means that
if it doesn't exist, the descriptor returned will be NULL.
Then we can add error handling and also avoid just doing this on
the device tree path, and simplify the site where the optional
GPIO descriptor is used.
There were some problems with cleaning up this GPIO descriptor
use in the past, but this is the proper way to deal with it.
Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20221107090753.1404679-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it possible to probe the GPIO VBUS detection driver
from the device tree compatible for GPIO USB B connectors.
Since this driver is using the "gpio-usb-b-connector"
compatible, it is important to discern it from the role
switch connector driver (which does not provide a phy),
so we add some Kconfig text and depend on !USB_CONN_GPIO.
Cc: Rob Herring <robh@kernel.org>
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221106230506.1646101-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/09bc980d8432a4b5f7d88388ec0df5b085583139.1667336095.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f01ef2ddaf12a6412127611617786adc1234e0b4.1667336095.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been pointed out that the kernel log messages warning about
problems in USB configuration and related descriptors are vexing for
users. The warning log level has a fairly high priority, but the user
can do nothing to fix the underlying errors in the device's firmware.
To reduce the amount of useless information produced by tools that
filter high-priority log messages, we can change these warnings to
notices, i.e., change dev_warn() to dev_notice(). The same holds for
a few messages that currently use dev_err(): Unless they indicate a
failure that might make a device unusable (such as inability to
transfer a config descriptor), change them to dev_notice() also.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216630
Suggested-by: Artem S. Tashkinov <aros@gmx.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Y2KzPx0h6z1jXCuN@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmNe+HAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrFwH/jYeSZl8ACW2GR7r
8zsyHK/qy7tOmwV99QZjS94b1KK1hfi2L93Ro8LXohqI3HDvk6eBXWApz3jSicFW
OeTCq1vu2Bw1iimhUThVqVCWF8EaVwdYYobvNqIznA2QCkOO+oTG+3oIiWJaEOVE
xKJypq95b16D0KAGXrgZznjdBi2DlOUzdsjNT3E8xSXeEjvX7y7optHhuMlCgir4
19kEgelGAOp28rd5l0qZ2pt0ltMN+COx4EF8LCNvsD2kvXPbyDN/V2Ql04mYBMde
hriWyP5W0WDOCvjrcxV4CgyosZ2UgkfAdZ1JTJQi3RkfJ1B52BpyfRiBkfQeqcC+
RoHbW7w=
=RWs8
-----END PGP SIGNATURE-----
Merge 6.1-rc3 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A use-after-free bugfix in the smscufx driver and various minor
error path fixes, smaller build fixes, sysfs fixes and
typos in comments in the stifb, sisfb, da8xxfb, xilinxfb, sm501fb,
gbefb and cyber2000fb drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCY16ulQAKCRD3ErUQojoP
XyvDAP9ZhF0SjbnRBwHAU9ZYC7XpCwcoqBRWFCCU7mmmbkXrJAD9F1LcEwZPGyn/
5/hiTwzM8ioJz6HB3r04M88bl4b1cwI=
=SnCh
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
"A use-after-free bugfix in the smscufx driver and various minor error
path fixes, smaller build fixes, sysfs fixes and typos in comments in
the stifb, sisfb, da8xxfb, xilinxfb, sm501fb, gbefb and cyber2000fb
drivers"
* tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: cyber2000fb: fix missing pci_disable_device()
fbdev: sisfb: use explicitly signed char
fbdev: smscufx: Fix several use-after-free bugs
fbdev: xilinxfb: Make xilinxfb_release() return void
fbdev: sisfb: fix repeated word in comment
fbdev: gbefb: Convert sysfs snprintf to sysfs_emit
fbdev: sm501fb: Convert sysfs snprintf to sysfs_emit
fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
fbdev: da8xx-fb: Fix error handling in .remove()
fbdev: MIPS supports iomem addresses
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Reported-by: Jeff Vanhoof <jdv1029@gmail.com>
Reported-by: Dan Vacura <w36195@motorola.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 19905240ae.
It was a new feature, and it doesn't even work properly yet, so revert
it from this branch as it is not needed for 6.1-final.
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@kernel.org>
Fixes: 19905240ae ("usb: gadget: uvc: limit isoc_sg to super speed gadgets")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.
If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.
So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.
Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.
This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)
Cc: stable@vger.kernel.org
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For optimal power consumption of USB4 routers the XHCI PCIe endpoint
used for tunneling must be in D3. Historically this is accomplished
by a long list of PCIe IDs that correspond to these endpoints because
the xhci_hcd driver will not default to allowing runtime PM for all
devices.
As both AMD and Intel have released new products with new XHCI controllers
this list continues to grow. In reviewing the XHCI specification v1.2 on
page 607 there is already a requirement that the PCI power management
states D3hot and D3cold must be supported.
In the quirk list, use this to indicate that runtime PM should be allowed
on XHCI controllers. The following controllers are known to be xHC 1.2 and
dropped explicitly:
* AMD Yellow Carp
* Intel Alder Lake
* Intel Meteor Lake
* Intel Raptor Lake
[keep PCI ID for Alder Lake PCH for recently added quirk -Mathias]
Cc: stable@vger.kernel.org
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-4-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ec ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This appears to fix the error:
"xhci_hcd <address>; ERROR Transfer event TRB DMA ptr not part of
current TD ep_index 2 comp_code 13" that appear spuriously (or pretty
often) when using a r8152 USB3 ethernet adapter with integrated hub.
ASM1042 reports as a 0.96 controller, but appears to behave more like 1.0
Inspired by this email thread: https://markmail.org/thread/7vzqbe7t6du6qsw3
Cc: stable@vger.kernel.org
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-2-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To ensure that child node is found, don't rely on child's node name
which can take different value, but on child's compatible name.
Fixes: f5c5936d6b ("usb: dwc3: st: Fix node's child name")
Cc: stable <stable@kernel.org>
Cc: Jerome Audu <jerome.audu@st.com>
Reported-by: Felipe Balbi <felipe@balbi.sh>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220930142018.890535-1-patrice.chotard@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
