When display lists are linked in a chain, they will be processed
automatically by the hardware, with each list linking to the next. Only
on the last display list will the frame end interrupt be fired to mark
the completion event.
Upon frame-end, the chain will be iterated to release each display list
back to the free list.
The chained lists use case (image partitioning) can require up to 64
lists per frame in the worst case scenario, bump up the number of
preallocated lists.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The new VSP1_ENTITY_PARAMS_PARTITION configuration parameters type
covers all registers that need to be configured for every partition.
This prepares for support of image partitioning, and replaces the
.set_memory() operation as the memory registers take different values
for every partition.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the current boolean parameter (full / !full) with an explicit
enum.
- VSP1_ENTITY_PARAMS_INIT for parameters to be configured at pipeline
initialization time only (V4L2 stream on or DRM atomic update)
- VSP1_ENTITY_PARAMS_RUNTIME for all parameters that can be freely
modified at runtime (through V4L2 controls)
This will allow future extensions when implementing image partitioning
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The RPF cropping offset for the chroma planes is incorrectly computed,
it needs to be divided by the horizontal subsampling factor.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cropping on the WPF sink pad restricts the left and top coordinates to
0-255. The same result can be obtained by cropping on the RPF without
any such restriction, this feature isn't useful. Disable it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The DFE and FRE interrupts are both fired at frame completion, as each
display list processes a single frame. This won't be true anymore when
using image partitioning, switch to DFE in preparation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The frame-end function releases and completes the buffers on the input
and output entities of the pipe before marking the pipe->state as
'STOPPED'. This introduces a race whereby with the pipe->state still
'RUNNING', a QBUF handler can commence processing a frame before the
frame_end function has completed.
In the event that this happens, a frame queued by QBUF hangs due to the
incorrect pipe->state setting which prevents vsp1_pipeline_run from
issuing a CMD_STRCMD.
By locking the entire function we prevent this from occurring, but we
also change the locking state of the buffer release code. This has been
analysed visually as acceptable, but it must be considered that this now
causes the video->irqlock to be taken under the pipe->irqlock context.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vsp1_pipeline_ready() and vsp1_pipeline_run() functions must be
called with the pipeline lock held, fix the resume code path.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The subdev userspace API isn't serialized in the core, serialize access
to formats and selection rectangles in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pipelines can only be run if all their video nodes are streaming. Commit
b4dfb9b35a ("[media] v4l: vsp1: Stop the pipeline upon the first
STREAMOFF") fixed the pipeline stop sequence, but introduced a race
condition that makes it possible to run a pipeline after stopping the
stream on a video node by queuing a buffer on the other side of the
pipeline.
Fix this by clearing the buffers ready flag when stopping the stream,
which will prevent the QBUF handler from running the pipeline.
Fixes: b4dfb9b35a ("[media] v4l: vsp1: Stop the pipeline upon the first STREAMOFF")
Reported-by: Kieran Bingham <kieran@bingham.xyz>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENOMEM from the memory or workqueue alloc
error handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENODEV from dma_request_slave_channel_compat()
error handling case instead of 0, as done elsewhere in this function.
Also fix to release resources in v4l2_clk_register() error handling.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the current format on the first open.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
trivial fix to spelling mistake in pr_debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Linking soc_mediabus into this driver causes multiple definition linker warnings
if soc_camera is also enabled:
drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_image_size+0x0): multiple definition of `__ksymtab_soc_mbus_image_size'
drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_image_size+0x0): first defined here
>> drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): multiple definition of `__ksymtab_soc_mbus_samples_per_pixel'
drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): first defined here
drivers/media/platform/soc_camera/built-in.o: In function `soc_mbus_config_compatible':
(.text+0x3840): multiple definition of `soc_mbus_config_compatible'
drivers/media/platform/soc_camera/soc_mediabus.o:(.text+0x134): first defined here
Since we really don't want to have to use any of the soc-camera code this patch
copies the relevant code and data structures from soc_mediabus and renames it to pxa_mbus_*.
The large table of formats has been culled a bit, removing formats that are not supported
by this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the R8A7792 VSP1V cores which are different from the other
gen2 VSP1 cores.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vsp1 driver supports tri-planar formats, but the DRM API only passes
two memory addresses. Add a third one.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of hardcoding the media device model and hardware revision to
"VSP1" and 0 respectively, report the actual hardware device model and
IP version number.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FCP must be powered up for the FDP1 to function, even when the FDP1
does not make use of the FCNL features. Extend the compatible list
to allow us to use the power domain and runtime-pm support.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Renesas multimedia drivers use ret to store return values, fix the
only exception in the rcar-fcp driver to keep the coding style
consistent.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This will allow adding new operations without increasing the
media_device structure size for drivers that don't implement any media
device operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by smatch:
drivers/media/platform/pxa_camera.c: In function 'pxa_dma_start_channels':
drivers/media/platform/pxa_camera.c:457:21: warning: variable 'active' set but not used [-Wunused-but-set-variable]
struct pxa_buffer *active;
^~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow building this driver if COMPILE_TEST is set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a tiny fix for a switch case which quiets 2 checkpatch harmless
warnings. The generated code is not affected.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the conversion to a v4l2 standalone device is finished, move
pxa_camera one directory up and finish severing any dependency to
soc_camera.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of the legacy behavior where it was required to wait for all
video buffers to be finished by the hardware, use a cancel like strategy
: as soon as the stop_streaming() call is done, abort all DMA transfers,
report the already buffers as failed and return.
This makes stop_streaming() more a "cancel capture" than a "wait for end
of capture" semantic.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch removes the soc_camera API dependency from pxa_camera.
In the current status :
- all previously captures are working the same on pxa270
- the s_crop() call was removed, judged not working
(see what happens soc_camera_s_crop() when get_crop() == NULL)
- if the pixel clock is provided by then sensor, ie. not MCLK, the dual
stage change is not handled yet.
=> there is no in-tree user of this, so I'll let it that way
- the MCLK is not yet finished, it's as in the legacy way,
ie. activated at video device opening and closed at video device
closing.
In a subsequence patch pxa_camera_mclk_ops should be used, and
platform data MCLK ignored. It will be the sensor's duty to request
the clock and enable it, which will end in pxa_camera_mclk_ops.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is to be seen as a regression as the set_selection (former
set_crop) function is removed. This is a temporary situation in the v4l2
porting, and will have to be added later.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make all print consistent by always using :
- dev_xxx(pcdev_to_dev(pcdev), ....)
This prepares the soc_camera adherence removal by making these call rely
on only pcdev, and not the soc_camera icd structure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Introduce sensor_call(), which will be used for all sensor invocations.
This is a preparation move to v4l2 device conversion, ie. soc_camera
adherence removal.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the functions in the file to be regrouped into meaningful blocks :
1. pxa camera core handling functions, manipulating the herdware
2. videobuf2 functions, dealing with video buffers
3. video ioctl (vidioc) related functions
4. driver probing, removal, suspend and resume
This patch doesn't modify a single line of code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert pxa_camera from videobuf to videobuf2.
As the soc_camera was already compatible with videobuf2, the port is
quite straightforward.
The special case of this code in which the vb2 to prepare is "too
big" in terms of size for the new capture format, the pxa_camera will
fail.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds the H.264 video encoding capability in the V4L2 HVA
video encoder driver for STMicroelectronics SoC (hva-h264.c).
The main supported features are:
- profile: baseline, main, high, stereo high
- level: up to 4.2
- bitrate mode: CBR, VBR
- entropy mode: CABAC, CAVLC
- video aspect: 1x1 only
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 HVA (Hardware Video Accelerator) video encoder
driver for STMicroelectronics SoC. It uses the V4L2 mem2mem framework.
This patch only contains the core parts of the driver:
- the V4L2 interface with the userland (hva-v4l2.c)
- the hardware services (hva-hw.c)
- the memory management utilities (hva-mem.c)
This patch doesn't include the support of specific codec (e.g. H.264)
video encoding: this support is part of subsequent patches.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the vivid EDID, fixing various incorrect values (wrong name,
product code, various video capabilities).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the 'IS_ERR_VALUE(irq)' with 'ret < 0' in
function 'atmel_isc_probe'.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch add g/s_selection for MT8173 V4L2 Encoder.
Only output queue support g/s_selection to configure crop.
The top/left of active rectangle should always be (0,0)
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_err() can not be used for printing error for missing interleaved
support in DMA as this point the pcdev->v4l2_dev is not valid.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When resuming from suspend-to-RAM on r8a7795/salvator-x:
dpm_run_callback(): pm_genpd_resume_noirq+0x0/0x90 returns 1
PM: Device fe940000.fdp1 failed to resume noirq: error 1
dpm_run_callback(): pm_genpd_resume_noirq+0x0/0x90 returns 1
PM: Device fe944000.fdp1 failed to resume noirq: error 1
dpm_run_callback(): pm_genpd_resume_noirq+0x0/0x90 returns 1
PM: Device fe948000.fdp1 failed to resume noirq: error 1
According to its documentation, rcar_fcp_enable() returns 0 on success
or a negative error code if an error occurs. Hence
fdp1_pm_runtime_resume() and vsp1_pm_runtime_resume() forward its return
value to their callers.
However, rcar_fcp_enable() forwards the return value of
pm_runtime_get_sync(), which can actually be 1 on success, leading to
the resume failure above.
To fix this, consider only negative values returned by
pm_runtime_get_sync() to be failures.
Fixes: 7b49235e83 ("[media] v4l: Add Renesas R-Car FCP driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
alloc_workqueue replaces deprecated create_singlethread_workqueue().
The MFC device driver is a v4l2 driver which can encode/decode video
raw/elementary streams and has support for all popular video codecs.
The driver's watchdog_workqueue has been replaced with system_wq since
it queues a single work item, &dev->watchdog_work, which calls for no
ordering requirement. The work item is involved in running the watchdog
timer and is not being used on a memory reclaim path.
Work item has been flushed in s5p_mfc_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Missing blank lines after declarations are making it hard to read the
code. Fix them and also fix other checkpatch warnings at the same time.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
