With this setting and AHBBRST at SBUSCFG as "Incremental burst of
unspecified length", each non-burst size can be taken as single
transfer. It is benefit for non-burst size transfer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Stream mode enable is known for better performance, this stream mode
enable patch has been passed with stress tests at device mode for
imx6sl and imx6sx, and no issue is found.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The system bus and chipidea IP have different limitations for
both host and device mode.
For example, with below errata, we need to enable SDIS(Stream Disable
Mode) at host mode. But we don't want it for device mode at the
same system.
TAR 9000378958
Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to
Hang on OUT Retry
Impacted Configuration: Host mode, all transfer types
Description:
The host core operating in streaming mode may under run while sending
the data packet of an OUT transaction. This under run can occur if
there are unexpected system delays in fetching the remaining packet
data from memory. The host forces a bad CRC on the packet, the device
detects the error and discards the packet. The host then retries a Bulk,
Interrupt, or Control transfer if an under run occurs according to the
USB specification. During simulations, it was found that the host does
not issue the retry of the failed bulk OUT. It does not issue any other
transactions except SOF packets that have incorrect frame numbers.
The second failure mode occurs if the under run occurs on an ISO OUT
transaction and the next ISO transaction is a zero byte packet. The host
does not issue any transactions (including SOFs). The device detects a
Suspend condition, reverts to full speed, and waits for resume signaling.
A third failure mode occurs when the host under runs on an ISO OUT and
the next ISO in the schedule is an ISO OUT with two max packets of 1024
bytes each. The host should issue MDATA for the first OUT followed by
DATA1 for the second. However, it drops the MDATA transaction, and
issues the DATA1 transaction.
The system impact of this bug is the same regardless of the failure mode
observed. The host core hangs, the ehci_ctrl state machine waits for the
protocol engine to send the completion status for the corrupted
transaction, which never occurs. No indication is sent to the host
controller driver, no register bits change and no interrupts occur.
Eventually the requesting application times out.
Detailed internal behavior:
The EHCI control state machine (ehci_ctrl) in the DMA block is responsible
for parsing the schedules and initiating all transactions. The ehci_ctrl
state machine passes the transaction details to the protocol block by
writing the transaction information in to the TxFIFO. It then asserts
the pe_hst_run_pkt signal to inform the host protocol state machine
(pe_hst_state) that there is a packet in the TxFIFO.
A tag of 0x0 indicates a start of packet with the data providing the
following information:
35:32 Tag
31:30 Reserved
29:23 Endpoint (lowest 4 bits)
22:16 Address
15:10 Reserved
9:8 Endpoint speed
7:6 Endpoint type
5:6 Data Toggle
3:0 PID
The pe_hst_state reads the packet information and constructs the packet
and issues it to the PHY interface.
The ehci_ctrl state machine writes the start transaction information in
to the TxFIFO as 0x03002910c for the OUT packet that had the under run
error. However, it writes 0xC3002910C for the retry of the Out
transaction, which is incorrect.
The pe_hst_state enters a bus timeout state after sending the bad CRC
for the packet that under ran. It then purges any data that was back
filled in to the TxFIFO for the packet that under ran. The pe_hst_state
machine stops purging the TxFIFO when it is empty or if it reads a
location that has a tag of 0x0, indicating a start of packet command.
The pe_hst_state reads 0xC3002910C and discards it as it does not decode
to a start of packet command. It continues to purge the OUT data that
has been pre-buffered for the OUT retry . The pe_hst_state detects the
hst_packet_run signal and attempts to read the PID and address
information from the TxFIFO. This location has packet data and so does
not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD
state where the frame_num_counter is updated. The frame_num_counter
is updated with the data in the TxFIFO. In this case, the data is
incorrect as the ehci_ctrl state machine did not initiate the load.
The hst_pe_state machine detects the SOF request signal and sends an
SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine
waits indefinitely in the run_pkt state waiting for the completion
status from pe_hst_state machine, which will never happen.
The ISO failure case is similar except that there is no retry for ISO.
The ehci_ctrl state machine moves to the next transfer in the periodic
schedule. If the under run occurs on the last entry of the periodic
list then it moves to the Async schedule.
In the case of ISO OUT simulations, the next ISO is a zero byte OUT
and again the start of packet command gets corrupted. The TxFIFO is
empty when the hst_pe_state attempts to read the Address and PID
information as the transaction is a zero byte packet. This results
in the hst_pe_state machine staying in the GET_PID state, which means
that it does not issue any transactions (including SOFs). The device
detects a Suspend condition and reverts to full speed mode and waits
for a Resume or Reset signal.
The EHCI specification allows a Non-DoubleWord (32 bits) offset to
be used as a current offset for Buffer Pointer Page 0 of the qTD.
In Non-DoubleWord aligned cases, the core reads the packet data
from the AHB memory, performs the alignment operation before writing
it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP)
is written to the TxFIFO after all the packet data has been written
in to the TxFIFO. The alignment function is reset to Idle by the EOP
tag. The corruption of the start of packet command arises because the
packet buffer for the OUT transaction that under ran is not aligned
to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The
alignment function is still active when the start packet information
is written in to the TxFIFO for the retry of the bulk packet or for
the next transaction in the case of an under run on an ISO. This
results in the corruption of the start tag and the transaction
information.
Click for waveform showing the command 0x 0000300291 being written in
to the TX FIFO for the Out that under ran.
Click for waveform showing the command 0xC3002910C written to the
TxFIFO instead of 0x 0000300291
Versions affected: Versions 2.10a and previous versions
How discovered: Customer simulation
Workaround:
1- The EHCI specification allows a non-DoubleWord offset to be used
as a current offset for Buffer Pointer Page 0 of the qTD. However,
if a DoubleWord offset is used then this issue does not arise.
2- Use non streaming mode to eliminate under runs.
Resolution:
The fix involves changes to the traffic state machine in the
vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context
information by encoding the transaction results on the
hst_op_context_update signals at the end of a transaction. The signal
hst_op_context_update is added to the traffic state machine, and the
tx_fifo_under_ran_r signal is generated if the transaction results in
an under run error. Click for waveform
The traffic state machine then traverses to the do_eop states if the
tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to
the TxFIFO as shown in this waveform .
The EOP tag resets the align state machine to the Idle state ensuring
that the next command written by the echi_ctrl state machine does not
get corrupted.
File(s) modified:
RTL code fixed: …..
Method of reproducing: This failure cannot be reproduced in the current
test bench.
Date Found: March 2010
Date Fixed: June 2010
Update information:
Added the RTL code fix
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The zero-length packet is the sendor tells the receiver that there
is no more data, so it is only needed at the TX side.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The system configuration API should be called before the controller
run, otherwise, undefined results may occur. So, we override hcd
reset API, and add system configuration API after controller reset.
Cc: Li Jun <peter.chen@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
If usbmisc hasn't probed yet, defer the probe.
It's not enough to check if the platform device for the OF node of the
usbmisc has been registered, but it also needs to have been probed
already before we can call imx_usbmisc_init().
This can happen if the order in which devices are probed change due to
async probing or on-demand probing of dependencies.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
This makes the function hw_alloc_repmap be declared to have a return
type of void now due to this particular function never returning
a error code to its caller due to this function always running
successfully to completion nor it's caller putting the return
value into a variable in order to check if a error code is passed
from the function hw_alloc_repmap when calling this function.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
The struct ci_hdrc is the drvdata for hcd device, so we don't
need to introduce extra ci_hdrc structure for ehci.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
It is used to configure controller parameters according to
platform data, like speed, stream mode, etc, both host and
device's initialization need it, most of code are the
same for both roles, with this new interface, it can reduce
the duplicated code and be easy to maintain in future.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
We can support USB OTG 1.3 USB_DEVICE_A_HNP_SUPPORT request when
the driver supports OTG FSM mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
For i.mx platform, set ttctrl.ttha with non-zero value only affects
sitd, and ehci core makes sure the schedule is not full when accepts
new request, so it will not occur the transaction which will acorss
the SoF.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since some chipidea based controller is not otg capable, add ci->is_otg
condition when setting is_otg flag for gadget.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After introduce usb otg properties, update ci_otg_is_fsm_mode conditions
to be depending on both usb hardware properties and usb driver config,
also resolve a compile issue in debug.c after the API change.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.
Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just a minor change for code style
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVdQexAAoJEEhZKYFQ1nG7/M0H/3gZcnjvF2nN6NYBUhFpz33r
BAIDYumRhAPOVbnmXYZOh24+yPEhKYTWaZycjQeJXBVd23r8EFGP4Vl+K6vCTtJX
jIQZ+73ntPwDBgvDfPN1Lk+Kj2G3dPl6b+ZmmAj1lS1ea2ewDR5Q+OM3/bX6kscN
zccMIMv/++jLOvAeOvoa5Hk7JZdQK+DQaSCLRZAfEfID40I0A7j6OcWP3B8qebGD
faYc9XfA+Li/C1q7qvUFWTWHcVkQT56syffLXetts3sOuo7EzPlyyBT6zreKi//a
MHWv+VBkoQvqDYej7fLqfpRBy221beEfFXH5DAcDRr7q1ikKUIPWxiqwUOnJ4P0=
=Yq7y
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-work
Peter writes:
USB Chipidea update for v4.2-rc1
Just a minor change for code style
The Marvell 28nm HSIC PHY requires the port to be forced to HS mode after
the port power is applied. This is done using the test mode in the PORTSC
register.
As HSIC is always HS, this work-around should be safe to do with all HSIC
PHYs and has been tested on i.MX6S.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, ci_default_pdata is common to all instances of the driver and
gets modified by the core driver code. This is bad if there are multiple
instances of the device with different settings such as the phy type. Fix
this by making a copy of the default platform_data.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unneeded semicolon.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/semicolon.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
A string written by the user may not be zero terminated.
sscanf may read memory beyond the buffer if no zero byte
is found.
For testing build with CONFIG_USB_CHIPIDEA=y, CONFIG_USB_CHIPIDEA_DEBUG=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Wrongly release mutex lock during otg_statemachine may result in re-enter
otg_statemachine, which is not allowed, we should do next state transtition
after previous one completed.
Fixes: 826cfe751f ("usb: chipidea: add OTG fsm operation functions implementation")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the required clock to access registers is gated off in low power mode,
add ci->in_lpm check before try to dump registers value.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
By pass pullup DP in OTG fsm mode when do gadget connect, to let it handled
by OTG state machine.
This patch can fix the problem you found with my HNP polling patchset after
below 3 patches introduced:
467a78c usb: chipidea: udc: apply new usb_udc_vbus_handler interface
628ef0d usb: udc: add usb_udc_vbus_handler
dfea9c9 usb: udc: store usb_udc pointer in struct usb_gadget
Problem:
- Connect USB cable and MicroAB cable between two boards
- Boot up two boards
- load g_mass_storage at B-device side, the enumeration will success,
and A will see a usb mass-storage device
- load g_mass_storage at A-device side, the problem has occurred, the
connection will be lost at the beginning, then connect again.
This patch is based on
commit eff933c1d3a2e046492b3dfc86db813856553a29
(chipidea: pci: make it depends on NOP_USB_XCEIV)
on branch peter-usb-dev of
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
After commit ba1aff67f9 (chipidea: pci: register nop PHY) the PCI glue driver
requires nop-PHY to be selected. Thus, make it an explicit dependency.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ba1aff67f9 (chipidea: pci: register nop PHY)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces USB_CHIPIDEA_PCI and USB_CHIPIDEA_OF Kconfig options, one
per each specific glue driver. This is needed to provide different dependencies
they have.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current otg fsm timers are using controller 1ms irq and count it, this patch
is to replace it with hrtimer solution, use one hrtimer for all otg timers.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
B_DATA_PLS(data-line pulse time) and B_SSEND_SRP(session end to SRP init) are
also from OTG&EH 2.0 Specification and they are not chipidea specific.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since BSV irq is enabled for B-device all the time, so B_SESS_VLD timer
is not required, and also no need to check BSV status when B_ASE0_BRST
timer timeout.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
It can move all pullup/pulldown operation control to udc-core
through usb_gadget_connect/usb_gadget_disconnect according to
vbus status.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds runtime power management support for otg fsm mode, since
A-device in a_idle state cannot detect data pulse irq after suspended, here
enable wakeup by connection before suspend to make it can be resumed by DP;
and handle wakeup from that state like SRP.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CI_HDRC_TURN_VBUS_EARLY_ON is set, turn on vbus before adding hcd, so it
will not set reg_vbus of ehci_ci_priv, then vbus will not be handled by ehci core.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PHY for ChipIdea is optional (not all SoCs having PHY for ChipIdea should
be programmed), we register 'nop' PHY for platforms that do not have
programmable PHY.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For chipidea, its resume sequence is not-EHCI compatible, see
below description for FPR at portsc. So in order to send SoF in
time for remote wakeup sequence(within 3ms), the RUN/STOP bit must
be set before the resume signal is ended, but the usb resume
code may run after resume signal is ended, so we had to set it
at suspend path.
Force Port Resume - RW. Default = 0b.
1= Resume detected/driven on port.
0=No resume (K-state) detected/driven on port.
Host mode:
Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if
a J-to-K transition is detected while the port is in the Suspend state. When this bit
transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in
the USBSTS register is also set to '1'. This bit will automatically change to '0' after the
resume sequence is complete. This behavior is different from EHCI where the controller
driver is required to set this bit to a '0' after the resume duration is timed in the driver.
Note that when the controller owns the port, the resume sequence follows the defined
sequence documented in the USB Specification Revision 2.0. The resume signaling
(Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain
a '1' until the port has switched to idle. Writing a '0' has no affect because the port
controller will time the resume operation, clear the bit and the port control state switches
to HS or FS idle.
This field is '0' if Port Power(PP) is '0' in host mode.
This bit is not-EHCI compatible.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PORTSC_PFSC is not set on entering host mode which means the USB OTG
controller will attempt to enumerate USB devices at high speed even when the
CI_HDRC_FORCE_FULLSPEED flag is set in the platform data.
This patch ensures it is set right before host mode operations begin if needed.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At chipidea revision 2.40a, there is a below errata:
9000531823 B2-Medium Adding a dTD to a Primed Endpoint May Not Get Recognized
Title: Adding a dTD to a Primed Endpoint May Not Get Recognized
Impacted Configuration: All device mode configurations.
Description:
There is an issue with the add dTD tripwire semaphore (ATDTW bit in USBCMD register)
that can cause the controller to ignore a dTD that is added to a primed endpoint.
When this happens, the software can read the tripwire bit and the status bit at '1'
even though the endpoint is unprimed.
After executing a dTD, the device controller endpoint state machine executes a final
read of the dTD terminate bit to check if the application added a dTD to the linked
list at the last moment. This read is done in the finpkt_read_latest_next_td (44) state.
After the read is performed, if the terminate bit is still set, the state machine moves
to unprime the endpoint. The decision to unprime the endpoint is done in the
checkqh_decision (59) state, based on the value of the terminate bit.
Before reaching the checkqh_decision state, the state machine traverses the
writeqhtd_status (57), writeqh_status (56), and release_prime_mask (42) states.
As shown in the waveform, the ep_addtd_tripwire_clr signal is not set to clear
the tripwire bit in these states.
Workaround:
The software must implement a periodic poll cycle, and check for each dTD
pending on execution (Active = 1), if the enpoint is primed. It can do this by reading
the corresponding bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are
read at 0, the software needs to re-prime the endpoint by writing 1 to the corresponding
bit in the ENDPTPRIME register. This can be done for every microframe, every frame or
with a larger interval, depending on the urgency of transfer execution for the application.
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define ci_get_revision API to know the controller revision
information according to chipidea 1.1a, 2.0a and 2.5a spec.
Besides, add one entry at struct ci_hdrc to indicate revision
information, it can be used for adding different code for
revisions, eg kinds of errata.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using hw_write_id_reg and hw_read_id_reg to write and read identification
registers contents, they can be used to get controller information, change
some system configurations, and so on.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Except the same process with earlier imx6, it has below two features:
- Choose which vbus voltage as vbus wakeup source
We choose B_SESSION_VALID as vbus wakeup source since when the system
goes to suspend, the vbus comparator can't compare the vbus voltage
for VBUS_VALID.
- Disable dp/dm (linestate) change as wakeup source at device mode
when the vbus is not there, we don't expect dp/dm change waking up
usb controller at this situation.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to do it for all otg capable controller, not only peripheral
featured otg capable controller, otherwise, the host-only role, but
otg capable controller may be responded by otg interrupt.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable USB as system wakeup source, and each platform needs to implement
imx_usbmisc_set_wakeup in usbmisc_imx.c to support.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB signal can be system wakeup source, this patch add the
support, for how to enable it, see Documentation/usb/chipidea.txt.
Since USB wakeup enable logic is vendor/platform specific, the
glue layer needs to implement it to support this feature.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add runtime pm support for imx, only imx6 series are supported and tested.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to enable/disable usb wakeup, only imx6 series are
added, since I don't have other imx hardware on hand. Other imx users
can add their API according to reference manual after testing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move struct imx_usbmisc_data NULL pointer judgement from caller to
each API, it can simplify the caller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All imx usb controller's non core registers uses the same clock gate with
core registers, the usbmisc_imx is the library for imx glue driver, the
glue keeps clock on when it calls usbmisc_imx API to change non-core register.
Besides, we will support runtime pm in the future, it also needs to
close this clock when the usb is not in use.
Philipp Zabel also verifies it at imx6q platform, see
http://www.spinics.net/lists/linux-usb/msg118491.html
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is meaningless the glue layer driver has its own platform flag
which is the same meaning with common platform flag.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some gadget driver (like uac1) will try to enable endpoint again even
the ep is not empty, it will cause the ep reset again and may affect
the dTD list which has already queued.
It returns -EBUSY immediately, and indicate the endpoint is in use.
In this way, the ep's behavior will not be affected, and the gadget
driver is also notified.
Cc: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.
[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.293105] usb 1-1: can't set HNP mode: -32
[ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.466424] usb 1-1: can't set HNP mode: -32
[ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.636436] usb 1-1: can't set HNP mode: -32
[ 2.641003] usb usb1-port1: unable to enumerate USB device
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bGMq
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a follow up to the previously submitted commit cefa9a31a5 (ehci-pci:
disable for Intel MID platforms).
It includes the following changes:
- table and function are renamed to reflect this is not only about ChipIdea
- ChipIdea PCI driver (ci_hdrc_pci.c) gets the comment about the table in
ehci-pci.c
- MIPS IDs removed from the list since it was discovered and tested on Intel
MID platforms
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget power property will be used at get_status request.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 14b4099c07
It moved platform_set_drvdata(pdev, ci) before hcd is created,
and the hcd will assign itself as ci controller's drvdata during
the hcd creation function (in usb_create_shared_hcd), so it
overwrites the real ci's drvdata which we want to use.
So, if the controller is at host mode, the system suspend
API will get the wrong struct ci_hdrc pointer, and cause the
oops.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
drivers/usb/chipidea/ci_hdrc_usb2.c:108:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed typos in comments of 2 drivers/usb/chipidea files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB2 ChipIdea driver for ci13xxx, with optional PHY, clock
and DMA mask, to support USB2 ChipIdea controllers that don't need
specific functions.
Tested on the Marvell Berlin SoCs USB controllers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic plaftorm device for ChipIdea drivers is probed by calling
ci_hdrc_probe. The device structure used is not the one of the specific
ChipIdea driver but the one of the generic ChipIdea platform device.
This results in not being able to probe the PHYs as we're not using the
right device structure. Since all ChipIdea drivers are retrieving their
PHYs in their specific driver code, this didn't impact any of them yet.
Fixes it using the right device structure (dev->parent).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core driver has already done it, besides, move set driver data
operation just after ci has allocated successfully in case some
code (like ci_role_start) want to access this driver data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hw_device_reset is dedicated to be used at device mode initializaiton,
so delete the parameter 'mode'. For host driver, the ehci driver will
handle all things.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add controller reset API, currently it is used for device mode only.
It may be used for host/otg driver in future.
Ususally, we need this API for dual-role switch and back from hibernation
suspend to let the controller at default state.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, USB PHY is mandatory for chipidea core, the flag
CI_HDRC_REQUIRE_TRANSCEIVER is useless.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic system power management support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add system power management support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy needs some delay to output the stable status from low
power mode. And for OTGSC, the status inputs are debounced
using a 1 ms time constant, so, delay 2ms for controller to get
the stable status(like vbus and id) when the phy leaves low power.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The individual PHY driver should take this responsibility if it
needs to delay between clear portsc.phcd and let the phy leave
low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to do an intermediate step for reading the
MX53_USB_OTG_PHY_CTRL_1_OFFSET register.
Read it directly instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 'evdo' property is not defined, then reading the MX25_USB_PHY_CTRL_OFFSET
register is an unneeded operation.
Move the reading of MX25_USB_PHY_CTRL_OFFSET inside the 'evdo' if block code,
where it is actually used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MM core code already complains when devm_kzalloc() fails, so no need to print
the error locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MM core code already complains when devm_kzalloc() fails, so no need to print
the error locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_request_irq to instead of request_irq.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an external portpower override callback, only single
port regulator control is supported now.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support of the PHY framework for ChipIdea drivers.
Changes are done in both the ChipIdea common code and in the drivers
accessing the PHY. This is done by adding a new PHY member in
ChipIdea's structures and by taking care of it in the code.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The call of 'kfree(ci->hw_bank.regmap)' in ci_hdrc_remove() sometimes causes
a kernel oops when removing the ci_hdrc module.
Since there is no separate memory allocated for the ci->hw_bank.regmap array,
there is no need to free it.
Cc: v3.14+ <stable@@vger.kernel.org>
Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB PHY member of the HCD structure is renamed to 'usb_phy' and
modifications are done in all drivers accessing it.
This is in preparation to adding the generic PHY support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
[Sergei: added missing 'drivers/usb/misc/lvstest.c' file, resolved rejects,
updated changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some kernel-doc style comment are not satisfied for format, fix them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have only needed to enable otg initialization when both of
below conditions are satisfied:
- The controller is otg capable
- The gadget function is enabled
If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize USB PHY after every Link controller reset
Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY drivers keep track of the current state of the hardware,
so don't change PHY settings under it.
Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2ZIACgkQMUfUDdst+ylvQwCfQKPKcwhtq4vJ2imUzJROEZwN
ygYAnRpFpH/19X59uGSdE7DAdhbitqKg
=uPh1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
Fixes the following sparse warnings:
drivers/usb/chipidea/debug.c:211:5: warning:
symbol 'ci_otg_show' was not declared. Should it be static?
drivers/usb/chipidea/debug.c:334:5: warning:
symbol 'ci_registers_show' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-ENODEV is interpreted by the generic driver probing function as a
non-matching driver. This leads to a missing probe failure message.
Also a missing USB PHY is more of an invalid configuration of the usb
driver because it is necessary.
This patch returns -EINVAL if devm_usb_get_phy_by_phandle() returned -ENODEV.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 2 methods for ZLP (zero-length packet) generation:
1) In software
2) Automatic generation by device controller
1) is implemented in UDC driver and it attaches ZLP to IN packet if
descriptor->size < wLength
2) can be enabled/disabled by setting ZLT bit in the QH
When gadget ffs is connected to ubuntu host, the host sends
get descriptor request and wLength in setup packet is 255 while the
size of descriptor which will be sent by gadget in IN packet is
64 byte. So the composite driver sets req->zero = 1.
In UDC driver following code will be executed then
if (hwreq->req.zero && hwreq->req.length
&& (hwreq->req.length % hwep->ep.maxpacket == 0))
add_td_to_list(hwep, hwreq, 0);
Case-A:
So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet.
ubuntu host will request 255 byte in IN request, gadget will send 64 byte
with ZLP and host will come to know that there is no more data.
But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to
automatically generate the ZLP which blocks enumeration for ~6 seconds due
to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING)
Case-B:
In case when gadget ffs is connected to Apple device, Apple device sends
setup packet with wLength=64. So descriptor->size = 64 and wLength=64
therefore req->zero = 0 and UDC driver will not attach any ZLP to the
IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't
further request for IN data. But ZLT=0 by default for endpoint 0 so
hardware tries to automatically generate the ZLP which blocks enumeration
for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any
requests (OUT/PING)
According to USB2.0 specs:
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase in which the
host requests more data than is contained in the specified data
structure. When all of the data structure is returned to the host,
the function should indicate that the Data stage is ended by
returning a packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of wMaxPacketSize
for the pipe, the function will return a zero-length packet to indicate
the end of the Data stage.
In Case-A mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software
ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then
enumeration doesn't block for 6 seconds.
In Case-B mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint then enumeration
still blocks due to ZLP automatically generated by hardware and host not needing
it. But if we keep software ZLP generation enabled but we set ZLT=1 for
endpoint 0 then enumeration doesn't block for 6 seconds.
So the proper solution for this issue seems to disable automatic ZLP generation
by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver)
handle the ZLP generation based on req->zero field.
Cc: stable@vger.kernel.org
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to delete un-finished td from current request's td list
at ep_dequeue API, otherwise, this non-user td will be remained
at td list before this request is freed. So if we do ep_queue->
ep_dequeue->ep_queue sequence, when the complete interrupt for
the second ep_queue comes, we search td list for this request,
the first td (added by the first ep_queue) will be handled, and
its status is still active, so we will consider the this transfer
still not be completed, but in fact, it has completed. It causes
the peripheral side considers it never receives current data for
this transfer.
We met this problem when do "Error Recovery Test - Device Configured"
test item for USBCV2 MSC test, the host has never received ACK for
the IN token for CSW due to peripheral considers it does not get this
CBW, the USBCV test log like belows:
--------------------------------------------------------------------------
INFO
Issuing BOT MSC Reset, reset should always succeed
INFO
Retrieving status on CBW endpoint
INFO
CBW endpoint status = 0x0
INFO
Retrieving status on CSW endpoint
INFO
CSW endpoint status = 0x0
INFO
Issuing required command (Test Unit Ready) to verify device has recovered
INFO
Issuing CBW (attempt #1):
INFO
|----- CBW LUN = 0x0
INFO
|----- CBW Flags = 0x0
INFO
|----- CBW Data Transfer Length = 0x0
INFO
|----- CBW CDB Length = 0x6
INFO
|----- CBW CDB-00 = 0x0
INFO
|----- CBW CDB-01 = 0x0
INFO
|----- CBW CDB-02 = 0x0
INFO
|----- CBW CDB-03 = 0x0
INFO
|----- CBW CDB-04 = 0x0
INFO
|----- CBW CDB-05 = 0x0
INFO
Issuing CSW : try 1
INFO
CSW Bulk Request timed out!
ERROR
Failed CSW phase : should have been success or stall
FAIL
(5.3.4) The CSW status value must be 0x00, 0x01, or 0x02.
ERROR
BOTCommonMSCRequest failed: error=80004000
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update device states according to ch9 in USB 2.0 specification
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 62bb84e (usb: gadget: ci13xxx: convert to platform device)
start address of the capability registers is not passed correctly to
udc_probe(). Fix this.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows controller to be specified via device tree.
Pass PHY phandle specified in DT to core driver.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field PLLDIVVALUE of register PHY_CTRL_1 selects the reference clock source
for the PHY:
00 = sysclock uses 19.2 MHz
01 = sysclock uses 24 MHz
10 = sysclock uses 26 MHz
11 = sysclock uses 27 MHz
The reset value for this field is 10 according to the reference manual, and
even though this reset value works for mx53, it does not work for mx51.
So instead of relying on the reset value for the PLLDIVVALUE field, explicitly
set it to 01 so that a 24MHz clock can be selected for the PHY and allowing both
mx51 and mx53 to have USB OTG port functional.
Succesfully tested 'g_ether' on a imx51-babbage and on a imx53-qsb boards.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The otg queue work include operations: one is disable interrupt,
another one is call kernel queue work API. Many codes do this
operation, using one inline function to instead of them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a debug file for OTG vairables show.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds sys input to control and show OTG fsm inputs by application,
user can do host and preipheral role switch by change these inputs.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB OTG interrupt handling and fsm transitions according to USB OTG
and EH 2.0.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds OTG fsm timers initialization, which use controller's 1ms
interrupt as timeout counter, also adds some local timers which are not
in otg_fsm_timer list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add b_hnp_enable request handling and enable gadget->is_otg
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Init otg_port number of otg capable host to be 1 at host start.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leave vbus on/off hanlded by OTG fsm if in OTG mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds OTG fsm related initialization when do otg init,
add a seperate file for OTG fsm related utilities.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the PHY has powered and initialized, it needs some delay
for controller to reflect PHY's status. Some status and values
for id, vbus, dp/dm are only stable after this delay. The current
code tries to clear id/vbus status without enough delay, it
causes the status are not cleared properly.
This patch add 2ms delay after phy has initialized, and clear the
unexpected status after that.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves usb interrupt enable and status register read functions
from udc driver to core driver to use them in all ci drivers.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a more general way to read and write otgsc register.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For internal PHY (like UTMI), the phy clock may from internal pll,
it is on/off on the fly, the access PORTSC.PTS will hang without
phy clock. So, the usb_phy_init which will open phy clock needs to
be called before hw_phymode_configure.
See: http://marc.info/?l=linux-arm-kernel&m=139350618732108&w=2
For external PHY (like ulpi), it needs to configure portsc.pts before
visit viewport, or the viewport can't be visited. so phy_phymode_configure
needs to be called before usb_phy_init.
See: cd0b42c2a6
It may not the best solution, but it can work for all situations.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Cc: shc_work@mail.ru
Cc: denis@eukrea.com
Cc: festevam@gmail.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the i.MX25 and the i.MX35 support in the
ChipIdea usbmisc driver.
The i.MX25 and i.MX35 usb controllers are similar enough to be
able to use the same code.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB controller in TI-NSPIRE calculators (LSI Zevio SoC) are based off either
Freescale's USB OTG controller or the USB controller found in the IMX233, both
of which are Chipidea compatible.
This patch adds a device tree binding for the controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_name() for ci_hdrc name to distinguish USBs
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthieu CASTET and Michael Grzeschik mentioned isr_tr_complete_handler
is a bit messy at below:
http://marc.info/?l=linux-usb&m=139047775001152&w=2
This commit creates a new function isr_setup_packet_handler to handle
setup packet, it makes isr_tr_complete_handler easy to read.
This is no functional change at this commit, tested with g_mass_storage
and g_ether.
Cc: Michael Grzeschik <mgr@pengutronix.de>
Cc: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to set the chipidea udc into full-speed only mode.
It is set by the oftree property "maximum-speed = full-speed".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead
of accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- delete the warning message at interrupt handler, and adds judgement at
ep_enable, if non-ep0 requests ctrl transfer, it will indicate an error.
- delete hw_test_and_clear_setup_status which is a broken code
- Tested with g_mass_storage, g_ncm, g_ether
Cc: matthieu.castet@parrot.com
Reported-by: Michael Grzeschik <mgr@pengutronix.de>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Tested-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Delete global_phy due to we can get the phy from phy layer now
- using devm_usb_get_phy to instead of usb_get_phy
- delete the otg_set_peripheral, which should be handled by otg layer
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".
The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.
We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).
Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.
For stable tree: 3.11+.
Cc: stable <stable@vger.kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For otgsc, both enable bits and status bits are in it. So we need
to make sure the status bits are not be cleared when write enable
bits. It can fix one bug that we plug in/out Micro AB cable fast,
and sometimes, the IDIS will be cleared wrongly when handle last
ID interrupt (ID 0->1), so the current interrupt will not occur.
For stable tree: 3.12+
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw_phymode_configure configures the PORTSC registers and allow the
following phy_inits to operate on the right parameters. This fix a problem
where the UPLI (ISP1504) could not be detected, because the Viewport was not
available and read the viewport return 0's only.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* init the sts flag to 0 (missed)
* fix write the real bit not sts value
* Set PORTCS_STS and DEVLC_STS only if sts = 1
[Peter Chen: This one and the next patch fix the problem occurred imx27
and imx31, and imx27 and imx31 usb support are enabled until 3.14, so
these two patches isn't needed for -stable]
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
This patch is needed for stable tree 3.11+
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
This patch is needed for stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 30666249ea, as it
depended on a previous patch that I rejected, causing a build error
here. Sorry about that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as
"const". Further, as all offset fit into a single byte, the type is changed
from uintptr_t to u8.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch a seperate chunk of memory is allocated for the regmap
array. As the regmap is always used it makes no sense to allocate a seperate
memory block for it, this patch moves the regmap array directly into the struct
hw_bank.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=N4//
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next
Linux 3.13-rc5
* tag 'v3.13-rc5': (231 commits)
Linux 3.13-rc5
aio: clean up and fix aio_setup_ring page mapping
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Don't set the INITRD_COMPRESS environment variable automatically
mm: fix build of split ptlock code
pstore: Don't allow high traffic options on fragile devices
mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
mm: page_alloc: revert NUMA aspect of fair allocation policy
Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
mm/hugetlb: check for pte NULL pointer in __page_check_address()
fix build with make 3.80
...
Conflicts:
drivers/usb/phy/Kconfig
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.
For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().
Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.
This patch modifies UDC drivers by adding support for maxpacket_limit.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.
Fix this by adding the check.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX51 as the next user of the usbmisc driver.
Functionality is similar to i.MX53, so at this stage simply
reuse existing i.MX53 calls.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX27 and i.MX31 as the next user of the usbmisc driver.
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ci_hdrc_imx's probe needs usbmisc_imx to be loadded beforehand,
so it is better we load usbmisc_imx first.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap only needs to reallocate if the hw_read on the CAP register shows
lpm is used. Therefore the if() statement check the change.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.
Fix this by adding the check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the user chooses peripheral mode for this controller, the vbus
regulator doesn't need to get, since the host will supply the vbus,
it can save one vbus pin for other usage.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Frank Li <frank.li@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like http://marc.info/?l=linux-usb&m=138200449428874&w=2 said:
two more things are needed to be done:
- If host_start fails, the host_stop should not be called, so we
add check that ci->hcd is not NULL.
- if the host_start fails at the beginning, we need to consider
regulator mismatch issue.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses
the kernel while trying to remove and put the HCD which doesn't exist:
WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511
__dma_alloc+0x200/0x240()
coherent pool not initialised!
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c)
r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00
[<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c)
[<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c)
r4:df883a60 r3:df86ad00
[<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40)
r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80
[<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240)
r3:00000000 r2:c05fda00
[<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0)
[<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438)
[<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664)
[<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180)
[<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670
)
r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
...
---[ end trace c88ccaf3969e8422 ]---
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
task: df86ad00 ti: df882000 task.ti: df882000
PC is at usb_remove_hcd+0x10/0x150
LR is at host_stop+0x1c/0x3c
pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013
sp : df883b50 ip : df883b78 fp : df883b74
r10: c11f4c54 r9 : c0836450 r8 : df30c400
r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010
r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 2f29404a DAC: 00000015
Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240)
Stack: (0xdf883b50 to 0xdf884000)
...
Backtrace:
[<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c)
r6:df2ef410 r5:00000000 r4:df2c3010
[<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20)
r5:00000000 r4:df2c3010
[<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670)
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
[<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48)
...
---[ end trace c88ccaf3969e8423 ]---
Fix this so at least we can continue booting and get to a shell prompt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also clean up the last item of the pci id list to be "cleaner".
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to let the PHY enter/leave low power mode.
Before the controller going to work(at probe/resume), it needs to let
the PHY leave low power mode.
After the controller stopping working(at remove/suspend), it needs to
let the PHY enter low power mode to save power consumption.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the PHY operations are moved to core, delete the related
code at glue layer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY operations are common, so move them to core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It needs to free ci->hw_bank.regmap explicitly since it is not managed
resource.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like vbus, the dr_mode and phy_mode are also got from glue layer's
platform data or device node.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc-core will call gadget's driver->disconnect, so we should avoid
calling gadget's disconnect again at ci_udc_stop in case the gadget's
unbind free some structs which is still used at gadget's disconnect.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:
- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
data
This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.
This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.
Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For chipidea, the IP must know vbus before the controller
begins to run. So the .pullup should only be called when
the vbus is there.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CI_HDRC_REGS_SHARED stands for the controller registers is shared
with other USB drivers, if all USB drivers are at chipidea/, it doesn't
needed to be set.
CI_HDRC_PULLUP_ON_VBUS stands for pullup dp when the vbus is on. This
flag doesn't need to be set if the vbus is always on for gadget
since dp has always pulled up after the gadget has initialized.
So, the current code seems to misuse this two flags.
- When the gadget initializes, the controller doesn't need to run if
it depends on vbus (CI_HDRC_PULLUP_ON_VBUS), it does not relate to
shared register.
- When the gadget starts (load one gadget module), the controller
can run if vbus is on (CI_HDRC_PULLUP_ON_VBUS), it also does not
relate to shared register.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the gadget role starts, we need to make sure the vbus is lower
than OTGSC_BSV, or there will be an vbus interrupt since we use
B_SESSION_VALID as vbus interrupt to indicate connect and disconnect.
When the host role starts, it may not be useful to wait vbus to lower
than OTGSC_BSV, but it can indicate some hardware problems like the
vbus is still higher than OTGSC_BSV after we disconnect to host some
time later (5000 milliseconds currently), which is obvious not correct.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We add vbus interrupt handler at ci_otg_work, it uses OTGSC_BSV(at otgsc)
to know it is connect or disconnet event.
Meanwhile, we introduce two flags id_event and b_sess_valid_event to
indicate it is an id interrupt or a vbus interrupt.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move otg related things to otg file.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the initialization, it needs to disable all interrupts
enable bit as well as clear all interrupts status bits to avoid
exceptional interrupt.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we need otgsc to know vbus's status at some chipidea
controllers even it is peripheral-only mode. Besides, some
SoCs (eg, AR9331 SoC) don't have otgsc register even
the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS.
We inroduce flag CI_HDRC_DUAL_ROLE_NOT_OTG to indicate if the
controller is dual role, but not supports OTG. If this flag is
not set, we follow the rule that if DCCPARAMS_DC and DCCPARAMS_HC
are both 1 at CAP_DCCPARAMS, then this controller is otg capable.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The role's init will be called at probe procedure.
- The role's destroy will be called at fail patch
at probe and driver's removal.
- The role's start/stop will be called when specific
role has started.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file is mainly used to access otgsc currently, it may
add otg related things in the future.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useless at below cases:
- If we implement both usb host and device at chipidea driver.
- If we don't need phy->otg.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For boards which have board level vbus control (eg, through gpio), we
need to vbus operation according to below rules:
- For host, we need open vbus before start hcd, and close it
after remove hcd.
- For otg, the vbus needs to be on/off when usb role switches.
When the host roles begins, it opens vbus; when the host role
finishes, it closes vbus.
We put vbus operation to host as host is the only vbus user,
When we are at host mode, the vbus is on, when we are not at
host mode, vbus should be off.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vbus regulator is a common element for USB vbus operation,
So, move it from glue layer to core.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
