The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Marvell 88E6095/6095F switch chips. These
chips are similar to the 88e6131, so we can add the support to
mv88e6131.c easily.
Thanks to Gary Thomas <gary@mlbassoc.com> and Jesper Dangaard
Brouer <hawk@diku.dk> for testing various patches.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
..so that we can parse the DSA topology from 'ip link' output:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
4: lan1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
5: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue
6: lan3@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue
7: lan4@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix compiler warning about non-const format string.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocols should be able to use constant value for the descriptor.
Minor whitespace cleanup as well
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no gain using prefetch() in dev_hard_start_xmit(), since
we already had to read ops->ndo_select_queue pointer in dev_pick_tx(),
and both pointers are probably located in the same cache line.
This prefetch call slows down fast path because of a stall in address
computation.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove 2 TEST_FRAME hacks that are no longer needed. These allowed
sctp regression tests to compile before, but are no longer needed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor changes to queue hashing:
1. Use const on accessor functions
2. Export skb_tx_hash for use in drivers (see ixgbe)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than calling device pointer directly (which is incorrect with
net_device_ops), use the standard dev_change_mtu. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_sack_swap seems unnecessary so I pushed swap to the caller.
Also removed comment that seemed then pointless, and added include
when not already there. Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
A zero length frame filter was recently introduced in ROSE protocole.
Previous commit makes the same at AX25 protocole level.
This patch has the same purpose for NetRom protocole.
The reason is that empty frames have no meaning in NetRom protocole.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previous commit 244f46ae6e
was introduced a zero length frame filter for ROSE protocole.
This patch has the same purpose at AX25 frame level for the same
reason. Empty frames have no meaning in AX25 protocole.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NL80211_CMD_GET_MESH_PARAMS and NL80211_CMD_SET_MESH_PARAMS handlers
did not verify whether a function pointer is NULL (not supported by
the driver) before trying to call the function. The former nl80211
command is available for unprivileged users, too, so this can
potentially allow normal users to kill networking (or worse..) if
mac80211 is built without CONFIG_MAC80211_MESH=y.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
printk formats in prior commit were reversed/incorrect.
Compiled without warning on x86 and x86_64, but detected on ppc.
Signed-off-by: Tom Talpey <tmtalpey@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
As long as one task is holding the socket lock, then calls to
xprt_force_disconnect(xprt) will not succeed in shutting down the socket.
In particular, this would mean that a server initiated shutdown will not
succeed until the lock is relinquished.
In order to avoid the deadlock, we should ensure that xs_tcp_send_request()
closes the socket on EPIPE errors too.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This fixes a regression against FreeBSD servers as reported by Tomas
Kasparek. Apparently when using RPC over a TCP socket, the FreeBSD servers
don't ever react to the client closing the socket, and so commit
e06799f958 (SUNRPC: Use shutdown() instead of
close() when disconnecting a TCP socket) causes the setup to hang forever
whenever the client attempts to close and then reconnect.
We break the deadlock by adding a 'linger2' style timeout to the socket,
after which, the client will abort the connection using a TCP 'RST'.
The default timeout is set to 15 seconds. A subsequent patch will put it
under user control by means of a systctl.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
dev can be NULL in ip[6]_frag_reasm for skb's coming from RAW sockets.
Quagga's OSPFD sends fragmented packets on a RAW socket, when netfilter
conntrack reassembles them on the OUTPUT path you hit this code path.
You can test it with something like "hping2 -0 -d 2000 -f AA.BB.CC.DD"
With help from Jarek Poplawski.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sk_buff pointers should be freed with kfree_skb.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
broken by commit 5e739d1752aca4e8f3e794d431503bfca3162df4; AFAICS should
be -stable fodder as well...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Aced-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warnings from current gcc about using non-const strings as printf
args in TIPC. Compile tested only (not a TIPC user).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the regressions cause by
commit 1326c3d5a4
(v2.6.28-rc6-461-g23a12b1) broke the display of local and remote
addresses of an SIT tunnel in iproute2.
nt->parms is used by ipip6_tunnel_init() and therefore need to be
initialized first.
Tracked as http://bugzilla.kernel.org/show_bug.cgi?id=12868
Reported-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an unused parameter (addr_len) from tcp_recv_urg()
method in net/ipv4/tcp.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the behavior of allowing both sysctl and addrconf_dad_failure()
to set the disable_ipv6 parameter without any bad side-effects.
If DAD fails and accept_dad > 1, we will still set disable_ipv6=1,
but then instead of allowing an RA to add an address then
immediately fail DAD, we simply don't allow the address to be
added in the first place. This also lets the user set this flag
and disable all IPv6 addresses on the interface, or on the entire
system.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the NFSv4 server to make use of TCP autotuning behaviour, which
was previously disabled by setting the sk_userlocks variable.
Set the receive buffers to be big enough to receive the whole RPC
request, and set this for the listening socket, not the accept socket.
Remove the code that readjusts the receive/send buffer sizes for the
accepted socket. Previously this code was used to influence the TCP
window management behaviour, which is no longer needed when autotuning
is enabled.
This can improve IO bandwidth on networks with high bandwidth-delay
products, where a large tcp window is required. It also simplifies
performance tuning, since getting adequate tcp buffers previously
required increasing the number of nfsd threads.
Signed-off-by: Olga Kornievskaia <aglo@citi.umich.edu>
Cc: Jim Rees <rees@umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Add /proc/fs/nfsd/pool_stats to export to userspace various
statistics about the operation of rpc server thread pools.
This patch is based on a forward-ported version of
knfsd-add-pool-thread-stats which has been shipping in the SGI
"Enhanced NFS" product since 2006 and which was previously
posted:
http://article.gmane.org/gmane.linux.nfs/10375
It has also been updated thus:
* moved EXPORT_SYMBOL() to near the function it exports
* made the new struct struct seq_operations const
* used SEQ_START_TOKEN instead of ((void *)1)
* merged fix from SGI PV 990526 "sunrpc: use dprintk instead of
printk in svc_pool_stats_*()" by Harshula Jayasuriya.
* merged fix from SGI PV 964001 "Crash reading pool_stats before
nfsds are started".
Signed-off-by: Greg Banks <gnb@sgi.com>
Signed-off-by: Harshula Jayasuriya <harshula@sgi.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Avoid overloading the CPU scheduler with enormous load averages
when handling high call-rate NFS loads. When the knfsd bottom half
is made aware of an incoming call by the socket layer, it tries to
choose an nfsd thread and wake it up. As long as there are idle
threads, one will be woken up.
If there are lot of nfsd threads (a sensible configuration when
the server is disk-bound or is running an HSM), there will be many
more nfsd threads than CPUs to run them. Under a high call-rate
low service-time workload, the result is that almost every nfsd is
runnable, but only a handful are actually able to run. This situation
causes two significant problems:
1. The CPU scheduler takes over 10% of each CPU, which is robbing
the nfsd threads of valuable CPU time.
2. At a high enough load, the nfsd threads starve userspace threads
of CPU time, to the point where daemons like portmap and rpc.mountd
do not schedule for tens of seconds at a time. Clients attempting
to mount an NFS filesystem timeout at the very first step (opening
a TCP connection to portmap) because portmap cannot wake up from
select() and call accept() in time.
Disclaimer: these effects were observed on a SLES9 kernel, modern
kernels' schedulers may behave more gracefully.
The solution is simple: keep in each svc_pool a counter of the number
of threads which have been woken but have not yet run, and do not wake
any more if that count reaches an arbitrary small threshold.
Testing was on a 4 CPU 4 NIC Altix using 4 IRIX clients, each with 16
synthetic client threads simulating an rsync (i.e. recursive directory
listing) workload reading from an i386 RH9 install image (161480
regular files in 10841 directories) on the server. That tree is small
enough to fill in the server's RAM so no disk traffic was involved.
This setup gives a sustained call rate in excess of 60000 calls/sec
before being CPU-bound on the server. The server was running 128 nfsds.
Profiling showed schedule() taking 6.7% of every CPU, and __wake_up()
taking 5.2%. This patch drops those contributions to 3.0% and 2.2%.
Load average was over 120 before the patch, and 20.9 after.
This patch is a forward-ported version of knfsd-avoid-nfsd-overload
which has been shipping in the SGI "Enhanced NFS" product since 2006.
It has been posted before:
http://article.gmane.org/gmane.linux.nfs/10374
Signed-off-by: Greg Banks <gnb@sgi.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Convert the remaining refcount users.
As pointed out by Patrick McHardy, the protocols can be accessed safely using RCU.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
On the legacy netif_rx path, I incorrectly tried to optimise
the napi_complete call by using __napi_complete before we reenable
IRQs. This simply doesn't work since we need to flush the held
GRO packets first.
This patch fixes it by doing the obvious thing of reenabling
IRQs first and then calling napi_complete.
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski pointed out that my previous fix is broken for
VLAN+netpoll as if netpoll is enabled we'd end up in the normal
receive path instead of the VLAN receive path.
This patch fixes it by calling the VLAN receive hook.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to send to userspace "regulatory" events.
For now we just send an event when we change regulatory domains.
We also notify userspace when devices are using their own custom
world roaming regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even after commit "mac80211: deauth when interface is marked down"
(e327b847 on Linus tree), userspace still isn't notified when interface
goes down. There isn't a problem with this commit, but because of other
code changes it doesn't work on kernels >= 2.6.28 (works if same/similar
change applied on 2.6.27 for example).
The issue is as follows: after commit "mac80211: restructure disassoc/deauth
flows" in 2.6.28, the call to ieee80211_sta_deauthenticate added by
commit e327b847 will not work: because we do sta_info_flush(local, sdata)
inside ieee80211_stop (iface.c), all stations in interface are cleared, so
when calling ieee80211_sta_deauthenticate->ieee80211_set_disassoc (mlme.c),
inside ieee80211_set_disassoc we have this in the beginning:
sta = sta_info_get(local, ifsta->bssid);
if (!sta) {
The !sta check triggers, thus the function returns early and
ieee80211_sta_send_apinfo(sdata, ifsta) later isn't called, so
wpa_supplicant/userspace isn't notified with SIOCGIWAP.
This commit moves deauthentication to before flushing STA info
(sta_info_flush), thus the above can't happen and userspace is really
notified when interface goes down.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 requests a scan it awaits either a return code != 0 from
the scan function or the cfg80211_scan_done to be called. In case of
a STA mac80211's scan function ever returns 0 and queues the scan request.
If ieee80211_sta_work is executed and ieee80211_start_scan fails for
some reason cfg80211_scan_done will never be called but cfg80211 still
thinks the scan was triggered successfully and will refuse any future
scan requests due to drv->scan_req not being cleaned up.
If a scan is triggered from within the MLME a similar problem appears. If
ieee80211_start_scan returns an error, local->scan_req will not be reset
and mac80211 will refuse any future scan requests.
Hence, in both cases call ieee80211_scan_failed (which notifies cfg80211
and resets local->scan_req) if ieee80211_start_scan returns an error.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the lowest value amongst countries which do enable 5 GHz operation.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect local->wmm_acm bits were set for AC_BK and AC_BE. Fix this
and add some comments to make it easier to understand the AC-to-UP(pair)
mapping. Set the wmm_acm bits (and show WMM debug) even if the driver
does not implement conf_tx() handler.
In addition, fix the ACM-based AC downgrade code to not use the
highest priority in error cases. We need to break the loop to get the
correct AC_BK value (3) instead of returning 0 (which would indicate
AC_VO). The comment here was not really very useful either, so let's
provide somewhat more helpful description of the situation.
Since it is very unlikely that the ACM flag would be set for AC_BK and
AC_BE, these bugs are not likely to be seen in real life networks.
Anyway, better do these things correctly should someone really use
silly AP configuration (and to pass some functionality tests, too).
Remove the TODO comment about handling ACM. Downgrading AC is
perfectly valid mechanism for ACM. Eventually, we may add support for
WMM-AC and send a request for a TS, but anyway, that functionality
won't be here at the location of this TODO comment.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible to hit a kernel panic on NULL pointer dereference in
dev_queue_xmit() when sending power save buffered frames to a STA that
woke up from sleep. This happened when the buffered frame was requeued
for transmission in ap_sta_ps_end(). In order to avoid the panic, copy
the skb->dev and skb->iif values from the first fragment to all other
fragments.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When they were part of the now defunct ieee80211 component, these
messages were only visible when special debugging settings were enabled.
Let's mirror that with a new lib80211 debugging Kconfig option.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As my netpoll fix for net doesn't really work for net-next, we
need this update to move the checks into the right place. As it
stands we may pass freed skbs to netpoll_receive_skb.
This patch also introduces a netpoll_rx_on function to avoid GRO
completely if we're invoked through netpoll. This might seem
paranoid but as netpoll may have an external receive hook it's
better to be safe than sorry. I don't think we need this for
2.6.29 though since there's nothing immediately broken by it.
This patch also moves the GRO_* return values to netdevice.h since
VLAN needs them too (I tried to avoid this originally but alas
this seems to be the easiest way out). This fixes a bug in VLAN
where it continued to use the old return value 2 instead of the
correct GRO_DROP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the iptables cluster match. This match can be used
to deploy gateway and back-end load-sharing clusters. The cluster
can be composed of 32 nodes maximum (although I have only tested
this with two nodes, so I cannot tell what is the real scalability
limit of this solution in terms of cluster nodes).
Assuming that all the nodes see all packets (see below for an
example on how to do that if your switch does not allow this), the
cluster match decides if this node has to handle a packet given:
(jhash(source IP) % total_nodes) & node_mask
For related connections, the master conntrack is used. The following
is an example of its use to deploy a gateway cluster composed of two
nodes (where this is the node 1):
iptables -I PREROUTING -t mangle -i eth1 -m cluster \
--cluster-total-nodes 2 --cluster-local-node 1 \
--cluster-proc-name eth1 -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth1 \
-m mark ! --mark 0xffff -j DROP
iptables -A PREROUTING -t mangle -i eth2 -m cluster \
--cluster-total-nodes 2 --cluster-local-node 1 \
--cluster-proc-name eth2 -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth2 \
-m mark ! --mark 0xffff -j DROP
And the following commands to make all nodes see the same packets:
ip maddr add 01:00:5e:00:01:01 dev eth1
ip maddr add 01:00:5e:00:01:02 dev eth2
arptables -I OUTPUT -o eth1 --h-length 6 \
-j mangle --mangle-mac-s 01:00:5e:00:01:01
arptables -I INPUT -i eth1 --h-length 6 \
--destination-mac 01:00:5e:00:01:01 \
-j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
arptables -I OUTPUT -o eth2 --h-length 6 \
-j mangle --mangle-mac-s 01:00:5e:00:01:02
arptables -I INPUT -i eth2 --h-length 6 \
--destination-mac 01:00:5e:00:01:02 \
-j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
In the case of TCP connections, pickup facility has to be disabled
to avoid marking TCP ACK packets coming in the reply direction as
valid.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
BTW, some final notes:
* This match mangles the skbuff pkt_type in case that it detects
PACKET_MULTICAST for a non-multicast address. This may be done in
a PKTTYPE target for this sole purpose.
* This match supersedes the CLUSTERIP target.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Module specific data moved into per-net site and being allocated/freed
during net namespace creation/deletion.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
NEXTHDR_NONE doesn't has an IPv6 option header, so the first check
for the length will always fail and results in a confusing message
"too short" if debugging enabled. With this patch, we check for
NEXTHDR_NONE before length sanity checkings are done.
Signed-off-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We currently use the negative value in the conntrack code to encode
the packet verdict in the error. As NF_DROP is equal to 0, inverting
NF_DROP makes no sense and, as a result, no packets are ever dropped.
Signed-off-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes a possible crash due to the missing initialization
of the expectation class when nf_ct_expect_related() is called.
Reported-by: BORBELY Zoltan <bozo@andrews.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit 784544739a (netfilter: iptables:
lock free counters) broke a number of modules whose rule data referenced
itself. A reallocation would not reestablish the correct references, so
it is best to use a separate struct that does not fall under RCU.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Removing the BKL from FASYNC handling ran into the challenge of keeping the
setting of the FASYNC bit in filp->f_flags atomic with regard to calls to
the underlying fasync() function. Andi Kleen suggested moving the handling
of that bit into fasync(); this patch does exactly that. As a result, we
have a couple of internal API changes: fasync() must now manage the FASYNC
bit, and it will be called without the BKL held.
As it happens, every fasync() implementation in the kernel with one
exception calls fasync_helper(). So, if we make fasync_helper() set the
FASYNC bit, we can avoid making any changes to the other fasync()
functions - as long as those functions, themselves, have proper locking.
Most fasync() implementations do nothing but call fasync_helper() - which
has its own lock - so they are easily verified as correct. The BKL had
already been pushed down into the rest.
The networking code has its own version of fasync_helper(), so that code
has been augmented with explicit FASYNC bit handling.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The ip_queue module is missing the net-pf-16-proto-3 alias that would
causae it to be auto-loaded when a socket of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The ip6_queue module is missing the net-pf-16-proto-13 alias that would
cause it to be auto-loaded when a socket of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch moves the event reporting outside the lock section. With
this patch, the creation and update of entries is homogeneous from
the event reporting perspective. Moreover, as the event reporting is
done outside the lock section, the netlink broadcast delivery can
benefit of the yield() call under congestion.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch moves the preliminary checkings that must be fulfilled
to update a conntrack, which are the following:
* NAT manglings cannot be updated
* Changing the master conntrack is not allowed.
This patch is a cleanup.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch moves the assignation of the master conntrack to
ctnetlink_create_conntrack(), which is where it really belongs.
This patch is a cleanup.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch increases the statistics of packets drop if the sequence
adjustment fails in ipv4_confirm().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch modifies the proc output to add display of registered
loggers. The content of /proc/net/netfilter/nf_log is modified. Instead
of displaying a protocol per line with format:
proto:logger
it now displays:
proto:logger (comma_separated_list_of_loggers)
NONE is used as keyword if no logger is used.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch modifies nf_log to use a linked list of loggers for each
protocol. This list of loggers is read and write protected with a
mutex.
This patch separates registration and binding. To be used as
logging module, a module has to register calling nf_log_register()
and to bind to a protocol it has to call nf_log_bind_pf().
This patch also converts the logging modules to the new API. For nfnetlink_log,
it simply switchs call to register functions to call to bind function and
adds a call to nf_log_register() during init. For other modules, it just
remove a const flag from the logger structure and replace it with a
__read_mostly.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
It's not too likely to happen, would basically require crafted
packets (must hit the max guard in tcp_bound_to_half_wnd()).
It seems that nothing that bad would happen as there's tcp_mems
and congestion window that prevent runaway at some point from
hurting all too much (I'm not that sure what all those zero
sized segments we would generate do though in write queue).
Preventing it regardless is certainly the best way to go.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The results is very unlikely change every so often so we
hardly need to divide again after doing that once for a
connection. Yet, if divide still becomes necessary we
detect that and do the right thing and again settle for
non-divide state. Takes the u16 space which was previously
taken by the plain xmit_size_goal.
This should take care part of the tso vs non-tso difference
we found earlier.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's very little need for most of the callsites to get
tp->xmit_goal_size updated. That will cost us divide as is,
so slice the function in two. Also, the only users of the
tp->xmit_goal_size are directly behind tcp_current_mss(),
so there's no need to store that variable into tcp_sock
at all! The drop of xmit_goal_size currently leaves 16-bit
hole and some reorganization would again be necessary to
change that (but I'm aiming to fill that hole with u16
xmit_goal_size_segs to cache the results of the remaining
divide to get that tso on regression).
Bring xmit_goal_size parts into tcp.c
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that no variables clash such that we couldn't do
the check just once later on. Therefore move it.
Also kill dead obvious comment, dead argument and add
unlikely since this mtu probe does not happen too often.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wow, it was quite tricky to merge that stream of negations
but I think I finally got it right:
check & replace_ts_recent:
(s32)(rcv_tsval - ts_recent) >= 0 => 0
(s32)(ts_recent - rcv_tsval) <= 0 => 0
discard:
(s32)(ts_recent - rcv_tsval) > TCP_PAWS_WINDOW => 1
(s32)(ts_recent - rcv_tsval) <= TCP_PAWS_WINDOW => 0
I toggled the return values of tcp_paws_check around since
the old encoding added yet-another negation making tracking
of truth-values really complicated.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've already forgotten what for this was necessary, anyway
it's no longer used (if it ever was).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the pure assignment case, the earlier zeroing is
still in effect.
David S. Miller raised concerns if the ifs are there to avoid
dirtying cachelines. I came to these conclusions:
> We'll be dirty it anyway (now that I check), the first "real" statement
> in tcp_rcv_established is:
>
> tp->rx_opt.saw_tstamp = 0;
>
> ...that'll land on the same dword. :-/
>
> I suppose the blocks are there just because they had more complexity
> inside when they had to calculate the eff_sacks too (maybe it would
> have been better to just remove them in that drop-patch so you would
> have had less head-ache :-)).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking for a possible reason of bugzilla report on HTB oops:
http://bugzilla.kernel.org/show_bug.cgi?id=12858
I found the code in htb_delete calling htb_destroy_class on zero
refcount is very misleading: it can suggest this is a common path, and
destroy is called under sch_tree_lock. Actually, this can never happen
like this because before deletion cops->get() is done, and after
delete a class is still used by tclass_notify. The class destroy is
always called from cops->put(), so without sch_tree_lock.
This doesn't mean much now (since 2.6.27) because all vulnerable calls
were moved from htb_destroy_class to htb_delete, but there was a bug
in older kernels. The same change is done for other classful scheds,
which, it seems, didn't have similar locking problems here.
Reported-by: m0sia <m0sia@m0sia.ru>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->len is an unsigned int, so the test in x25_rx_call_request() always
evaluates to true.
len in x25_sendmsg() is unsigned as well. so -ERRORS returned by x25_output()
are not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Windows (XP at least) hosts on boot, with configured static ip, performing
address conflict detection, which is defined in RFC3927.
Here is quote of important information:
"
An ARP announcement is identical to the ARP Probe described above,
except that now the sender and target IP addresses are both set
to the host's newly selected IPv4 address.
"
But it same time this goes wrong with RFC5227.
"
The 'sender IP address' field MUST be set to all zeroes; this is to avoid
polluting ARP caches in other hosts on the same link in the case
where the address turns out to be already in use by another host.
"
When ARP proxy configured, it must not answer to both cases, because
it is address conflict verification in any case. For Windows it is just
causing to detect false "ip conflict". Already there is code for RFC5227, so
just trivially we just check also if source ip == target ip.
Signed-off-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to make xfrm_state objects hash on source address
broke the case where such source addresses are wildcarded.
Fix this by doing a two phase lookup, first with fully specified
source address, next using saddr wildcarded.
Reported-by: Nicolas Dichtel <nicolas.dichtel@dev.6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FC CRC offload check for ETH_P_FCOE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
RFC5061 states:
Each adaptation layer that is defined that wishes
to use this parameter MUST specify an adaptation code point in an
appropriate RFC defining its use and meaning.
If the user has not set one - assume they don't want to sent the param
with a zero Adaptation Code Point.
Rationale - Currently the IANA defines zero as reserved - and
1 as the only valid value - so we consider zero to be unset - to save
adding a boolean to the socket structure.
Including this parameter unconditionally causes endpoints that do not
understand it to report errors unnecessarily.
Signed-off-by: Malcolm Lashley <mlashley@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3758 Section 3.3.1. Sending Forward-TSN-Supported param in INIT
Note that if the endpoint chooses NOT to include the parameter, then
at no time during the life of the association can it send or process
a FORWARD TSN.
If peer does not support PR-SCTP capable, don't send FORWARD-TSN chunk
to peer.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix to indicate ASCONF support in INIT-ACK only if peer has
such capable.
This patch also fix to calc the chunk size if peer has no FWD-TSN
capable.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_inet_listen() call is split between UDP and TCP style. Looking
at the code, the two functions are almost the same and can be
merged into a single helper. This also fixes a bug that was
fixed in the UDP function, but missed in the TCP function.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: cleanup
node_to_cpumask (and the blecherous node_to_cpumask_ptr which
contained a declaration) are replaced now everyone implements
cpumask_of_node.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If xs_nospace() finds that the socket has disconnected, it attempts to
return ENOTCONN, however that value is then squashed by the callers.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Enforce the comment in xs_tcp_connect_worker4/xs_tcp_connect_worker6 that
we should delay, then retry on certain connection errors.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
While we should definitely return socket errors to the task that is
currently trying to send data, there is no need to propagate the same error
to all the other tasks on xprt->pending. Doing so actually slows down
recovery, since it causes more than one tasks to attempt socket recovery.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If we get an ECONNREFUSED error, we currently go to sleep on the
'xprt->sending' wait queue. The problem is that no timeout is set there,
and there is nothing else that will wake the task up later.
We should deal with ECONNREFUSED in call_status, given that is where we
also deal with -EHOSTDOWN, and friends.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
...so that we can distinguish between when we need to shutdown and when we
don't. Also remove the call to xs_tcp_shutdown() from xs_tcp_connect(),
since xprt_connect() makes the same test.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the socket is unconnected, and xprt_transmit() returns ENOTCONN, we
currently give up the lock on the transport channel. Doing so means that
the lock automatically gets assigned to the next task in the xprt->sending
queue, and so that task needs to be woken up to do the actual connect.
The following patch aims to avoid that unnecessary task switch.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Provide an api to attempt to load any necessary kernel RPC
client transport module automatically. By convention, the
desired module name is "xprt"+"transport name". For example,
when NFS mounting with "-o proto=rdma", attempt to load the
"xprtrdma" module.
Signed-off-by: Tom Talpey <tmtalpey@gmail.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Certain client rpc's which contain both lengthy page-contained
metadata and a non-empty xdr_tail buffer require careful handling
to avoid overlapped memory copying. Rearranging of existing rpcrdma
marshaling code avoids it; this fixes an NFSv4 symlink creation error
detected with connectathon basic/test8 to multiple servers.
Signed-off-by: Tom Talpey <tmtalpey@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Certain client-provided RPCRDMA chunk alignments result in an
additional scatter/gather entry, which triggered nfs/rdma server
assertions incorrectly. OpenSolaris nfs/rdma client connectathon
testing was blocked by these in the special/locking section.
Signed-off-by: Tom Talpey <tmtalpey@gmail.com>
Cc: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
To clear out old state, the UDP connect workers unconditionally invoke
xs_close() before proceeding with a new connect. Nowadays this causes
a spurious wake-up of the task waiting for the connect to complete.
This is a little racey, but usually harmless. The waiting task
immediately retries the connect via a call_bind/call_connect sequence,
which usually finds the transport already in the connected state
because the connect worker has finished in the background.
To avoid a spurious wake-up, factor the xs_close() logic that resets
the underlying socket into a helper, and have the UDP connect workers
call that helper instead of xs_close().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the transport isn't bound, then we should just return ENOTCONN, letting
call_connect_status() and/or call_status() deal with retrying. Currently,
we appear to abort all pending tasks with an EIO error.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We can Oops in both xs_udp_send_request() and xs_tcp_send_request() if the
call to xs_sendpages() returns an error due to the socket not yet being
set up.
Deal with that situation by returning a new error: ENOTSOCK, so that we
know to avoid dereferencing transport->sock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Some systems send SYN packets with apparently wrong RFC1323 timestamp
option values [timestamp tsval=0 tsecr=0].
It might be for security reasons (http://www.secuobs.com/plugs/25220.shtml )
Linux TCP stack ignores this option and sends back a SYN+ACK packet
without timestamp option, thus many TCP flows cannot use timestamps
and lose some benefit of RFC1323.
Other operating systems seem to not care about initial tsval value, and let
tcp flows to negotiate timestamp option.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not try to "uninitialize" ipv6 if its initialization had been skipped
because module parameter disable=1 had been specified.
Reported-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should probably not be testing any flags after we've cleared the
RPC_TASK_RUNNING flag, since rpc_make_runnable() is then free to assign the
rpc_task to another workqueue, which may then destroy it.
We can fix any races with rpc_make_runnable() by ensuring that we only
clear the RPC_TASK_RUNNING flag while holding the rpc_wait_queue->lock that
the task is supposed to be sleeping on (and then checking whether or not
the task really is sleeping).
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Since dev_set_name takes a printf style string, new gcc complains
if arg is not const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocols that use packet_type can be __read_mostly section for better
locality. Elminate any unnecessary initializations of NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
freq_diff is unsigned, so test before subtraction
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS mode, the beacon timestamp has to be filled with the
BSS's timestamp when joining, and set to zero when creating
a new BSS.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the AP thinks we are in power save state eventhough we are not truly
in that state, it sets the TIM bit and does not send a data frame unless
we send a null data frame to correct the state in the AP.
This might happen if the null data frame for wake up is lost in the air
after we disable power save.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to parse the AP's HT capabilities if
the STA uses TKIP/WEP cipher. This allows the rate control
module to choose the correct(legacy) rate table.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "mac80211/cfg80211: move iwrange handler to cfg80211", the
results for link quality from "iwlist scan" and "iwconfig" commands
have been very different. The results are now consistent.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported- and tested-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the driver is unconditionally notified of beacon
interval. This is a problem in AP mode, because the driver has
to know that the beacon interval has actualy changed to recalculate
TBTT and reset the HW TSF. Fix this to make mac80211 notify the driver
only when the beacon interval has been reconfigured to a new value.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.
Add a netdev_resync_ops() and call it from the vlan code.
Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.
With help from Patrick McHardy.
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A commit c1b56878fb "tc: policing requires
a rate estimator" introduced a test which invalidates previously working
configs, based on examples from iproute2: doc/actions/actions-general.
This is too rigorous: a rate estimator is needed only when police's
"avrate" option is used.
Reported-by: Joao Correia <joaomiguelcorreia@gmail.com>
Diagnosed-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change sctp_ctl_sock_init() to try IPv4 if IPv6 socket registration
fails. Required if the IPv6 module is loaded with "disable=1", else
SCTP will fail to load.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "disable" module parameter support to ipv6.ko by specifying
"disable=1" on module load. We just do the minimum of initializing
inetsw6[] so calls from other modules to inet6_register_protosw()
won't OOPs, then bail out. No IPv6 addresses or sockets can be
created as a result, and a reboot is required to enable IPv6.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is possible to do just about everything with the arp table
from user space except treat an entry like you are using it. To that end
implement and a flag NTF_USE that when set in a netwlink update request
treats the neighbour table entry like the kernel does on the output path.
This allows user space applications to share the kernel's arp cache.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, modular tokenring ("tr") lacks a license and fails to load:
tr: module license 'unspecified' taints kernel.
tr: Unknown symbol proc_net_fops_create
Beacuse of this, no tokenring driver can load if it depends on modular
tr. Fix this by adding GPL module license as it is in the kernel.
With this fix, tr module loads fine and tms380 driver also loads. Well,
it does'nt work but that's a different bug.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callers of netlink_set_err() currently pass a negative value
as parameter for the error code. However, sk->sk_err wants a
positive error value. Without this patch, skb_recv_datagram() called
by netlink_recvmsg() may return a positive value to report an error.
Another choice to fix this is to change callers to pass a positive
error value, but this seems a bit inconsistent and error prone
to me. Indeed, the callers of netlink_set_err() assumed that the
(usual) negative value for error codes was fine before this patch :).
This patch also includes some documentation in docbook format
for netlink_set_err() to avoid this sort of confusion.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink attribute parsing may be used even if CONFIG_NET is not set.
Move it from net/netlink to lib and control its inclusion based on the new
config symbol CONFIG_NLATTR, which is selected by CONFIG_NET.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.
Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb. So remove net_alive allowing
packet reception run a little faster.
Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To remove the possibility of packets flying around when network
devices are being cleaned up use reisger_pernet_subsys instead of
register_pernet_device.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently I had a kernel panic in icmp_send during a network namespace
cleanup. There were packets in the arp queue that failed to be sent
and we attempted to generate an ICMP host unreachable message, but
failed because icmp_sk_exit had already been called.
The network devices are removed from a network namespace and their
arp queues are flushed before we do attempt to shutdown subsystems
so this error should have been impossible.
It turns out icmp_init is using register_pernet_device instead
of register_pernet_subsys. Which resulted in icmp being shut down
while we still had the possibility of packets in flight, making
a nasty NULL pointer deference in interrupt context possible.
Changing this to register_pernet_subsys fixes the problem in
my testing.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network namespace is destroyed the network interfaces are
all unregistered, making addrconf_ifdown called by the netdevice
notifier.
In the other hand, the addrconf exit method does a loop on the network
devices and does addrconf_ifdown on each of them. But the ordering of
the netns subsystem is not right because it uses the register_pernet_device
instead of register_pernet_subsys. If we handle the loopback as
any network device, we can safely use register_pernet_subsys.
But if we use register_pernet_subsys, the addrconf exit method will do
exactly what was already done with the unregistering of the network
devices. So in definitive, this code is pointless.
I removed the netns addrconf exit method and moved the code to the
addrconf cleanup function.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit faee47cdbf
(sctp: Fix the RTO-doubling on idle-link heartbeats)
broke the RTO doubling for data retransmits. If the
heartbeat was sent before the data T3-rtx time, the
the RTO will not double upon the T3-rtx expiration.
Distingish between the operations by passing an argument
to the function.
Additionally, Wei Youngjun pointed out that our treatment
of requested HEARTBEATS and timer HEARTBEATS is the same
wrt resetting congestion window. That needs to be separated,
since user requested HEARTBEATS should not treat the link
as idle.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before or time_after are more robust
for comparing jiffies against other values.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in sctp_getsockopt_maxburst() doesn't allow len to be larger
then struct sctp_assoc_value, which is a common case where app writers
just pass down the sizeof(buf) or something similar.
This patch fix the problem.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the type name "AUTH" and primitive type name
"PRIMITIVE_ASCONF" for debug message.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The above functions from include/net/tcp.h have been defined with an
argument that they never use. The argument is 'u32 ack' which is never
used inside the function body, and thus it can be removed. The rest of
the patch involves the necessary changes to the function callers of the
above two functions.
Signed-off-by: Hantzis Fotis <xantzis@ceid.upatras.gr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ERROR chunk is received with too many error causes in ESTABLISHED
state, the kernel get panic.
This is because sctp limit the max length of cmds to 14, but while
ERROR chunk is received, one error cause will add around 2 cmds by
sctp_add_cmd_sf(). So many error causes will fill the limit of cmds
and panic.
This patch fixed the problem.
This bug can be test by SCTP Conformance Test Suite
<http://networktest.sourceforge.net/>.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An extra list_del() during the module load failure and unload
resulted in a crash with a list corruption. Now sctp can
be unloaded again.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem caused by the overlap of the connection-setup and
established-state phases of DCCP connections.
During connection setup, the client retransmits Confirm Feature-Negotiation
options until a response from the server signals that it can move from the
half-established PARTOPEN into the OPEN state, whereupon the connection is
fully established on both ends (RFC 4340, 8.1.5).
However, since the client may already send data while it is in the PARTOPEN
state, consequences arise for the Maximum Packet Size: the problem is that the
initial option overhead is much higher than for the subsequent established
phase, as it involves potentially many variable-length list-type options
(server-priority options, RFC 4340, 6.4).
Applying the standard MPS is insufficient here: especially with larger
payloads this can lead to annoying, counter-intuitive EMSGSIZE errors.
On the other hand, reducing the MPS available for the established phase by
the added initial overhead is highly wasteful and inefficient.
The solution chosen therefore is a two-phase strategy:
If the payload length of the DataAck in PARTOPEN is too large, an Ack is sent
to carry the options, and the feature-negotiation list is then flushed.
This means that the server gets two Acks for one Response. If both Acks get
lost, it is probably better to restart the connection anyway and devising yet
another special-case does not seem worth the extra complexity.
The result is a higher utilisation of the available packet space for the data
transmission phase (established state) of a connection.
The patch (over-)estimates the initial overhead to be 32*4 bytes -- commonly
seen values were around 90 bytes for initial feature-negotiation options.
It uses sizeof(u32) to mean "aligned units of 4 bytes".
For consistency, another use of 4-byte alignment is adapted.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a long-standing FIXME to dynamically update the Maximum
Packet Size depending on actual options usage.
It uses the flags set by the feature-negotiation infrastructure to compute
the required header option size.
Most options are fixed-size, a notable exception are Ack Vectors (required
currently only by CCID-2). These can have any length between 3 and 1020
bytes. As a result of testing, 16 bytes (2 bytes for type/length plus 14 Ack
Vector cells) have been found to be sufficient for loss-free situations.
There are currently no CCID-specific header options which may appear on data
packets, thus it is not necessary to define a corresponding CCID field as
suggested in the old comment.
Further changes:
----------------
Adjusted the type of 'cur_mps' to match the unsigned return type of the
function.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
I guess these fields were one day 16-bit in the struct but
nowadays they're just using 8 bits anyway.
This is just a precaution, didn't result any change in my
case but who knows what all those varying gcc versions &
options do. I've been told that 16-bit is not so nice with
some cpus.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
copied was assigned zero right before the goto, so if (copied)
cannot ever be true.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fixes insignificant bug that would cause sending of stale
SACK block (would occur in some corner cases).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that implementation in yeah was inconsistent to what
other did as it would increase cwnd one ack earlier than the
others do.
Size benefits:
bictcp_cong_avoid | -36
tcp_cong_avoid_ai | +52
bictcp_cong_avoid | -34
tcp_scalable_cong_avoid | -36
tcp_veno_cong_avoid | -12
tcp_yeah_cong_avoid | -38
= -104 bytes total
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to what is done elsewhere in TCP code when double
state checks are being done.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redundant checks made indentation impossible to follow.
However, it might be useful to make this ca_state+is_sack
indexed array.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some comment about its current state added. So far I have
seen very few cases where the thing is actually useful,
usually just marginally (though admittedly I don't usually
see top of window losses where it seems possible that there
could be some gain), instead, more often the cases suffer
from L-marking spike which is certainly not desirable
(I'll bury improving it to my todo list, but on a low
prio position).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Hannemann <hannemann@nets.rwth-aachen.de> noticed and was
puzzled by the fact that !tcp_is_fack(tp) leads to early return
near the beginning and the later on tcp_is_fack(tp) was still
used in an if condition. The later check was a left-over from
RFC3517 SACK stuff (== !tcp_is_fack(tp) behavior nowadays) as
there wasn't clear way how to handle this particular check
cheaply in the spirit of RFC3517 (using only SACK blocks, not
holes + SACK blocks as with FACK). I sort of left it there as
a reminder but since it's confusing other people just remove
it and comment the missing-feature stuff instead.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If cur_mss grew very recently so that the previously G/TSOed skb
now fits well into a single segment it would get send up in
parts unless we calculate # of segments again. This corner-case
could happen eg. after mtu probe completes or less than
previously sack blocks are required for the opposite direction.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) We didn't remove any skbs, so no need to handle stale refs.
2) scoreboard_skb_hint is trivial, no timestamps were changed
so no need to clear that one
3) lost_skb_hint needs tweaking similar to that of
tcp_sacktag_one().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb can be sent right away, we certainly should do that
if it's in the middle of the queue because it won't get
more data into it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that lost_cnt_hint gets underflow in
tcp_clean_rtx_queue because the cumulative ACK can cover
the segment where lost_skb_hint points to only partially,
which means that the hint is not cleared, opposite to what
my (earlier) comment claimed.
Also I don't agree what I ended up writing about non-trivial
case there to be what I intented to say. It was not supposed
to happen that the hint won't get cleared and we underflow
in any scenario.
In general, this is quite hard to trigger in practice.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Backtracking to sacked skbs is a horrible performance killer
since the hint cannot be advanced successfully past them...
...And it's totally unnecessary too.
In theory this is 2.6.27..28 regression but I doubt anybody
can make .28 to have worse performance because of other TCP
improvements.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Stephen Rothwell.
> Today's linux-next build (powerpc allyesconfig) failed like this:
>
> net/rds/cong.c: In function 'rds_cong_set_bit':
> net/rds/cong.c:284: error: implicit declaration of function 'generic___set_le_bit'
> net/rds/cong.c: In function 'rds_cong_clear_bit':
> net/rds/cong.c:298: error: implicit declaration of function 'generic___clear_le_bit'
> net/rds/cong.c: In function 'rds_cong_test_bit':
> net/rds/cong.c:309: error: implicit declaration of function 'generic_test_le_bit'
Signed-off-by: David S. Miller <davem@davemloft.net>
There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll. Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points. The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.
This patch adds the netpoll check to all entry points.
I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code). The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler
you're going to get a nice BUG_ON.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
"cfg80211: add assert_cfg80211_lock() to ensure proper protection"
added assert_cfg80211_lock() calls into various places. At least
one of them, nl80211_send_wiphy(), should not have been there. That
triggers the BUG_ON in assert_cfg80211_lock() and pretty much kills
the kernel whenever someone runs hostapd.. Remove that call and make
assert_cfg80211_lock() use WARN_ON instead of BUG_ON to be a bit more
friendly to users.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Give slow hardware some time to do the TSF sync, to not run into an
IBSS merging endless loop in some rarely situations.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was not a good idea to do a TSF reset on strange IBSS merges to the same BSSID. For example it will break the TSF sync of ath9k completely and it is unnecessary as all hardware I have tested do a TSF sync to a higher value automatically and IBSS merges are only done to higher TSF values. It only need a TSF reset to accept a lower value, when the IBSS network is changed manually.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we already have a regulatory request from the workqueue use that
and avoid a new kzalloc()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were passing value by value, lets just pass the struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When devices are world roaming they cannot beacon or do active scan
on 5 GHz or on channels 12, 13 and 14 on the 2 GHz band. Although
we have a good regulatory API some cards may _always_ world roam, this
is also true when a system does not have CRDA present. Devices doing world
roaming can still passive scan, if they find a beacon from an AP on
one of the world roaming frequencies we make the assumption we can do
the same and we also remove the passive scan requirement.
This adds support for providing beacon regulatory hints based on scans.
This works for devices that do either hardware or software scanning.
If a channel has not yet been marked as having had a beacon present
on it we queue the beacon hint processing into the workqueue.
All wireless devices will benefit from beacon regulatory hints from
any wireless device on a system including new devices connected to
the system at a later time.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current static world regulatory domain is too restrictive,
we can use some 5 GHz channels world wide so long as they do not
touch frequencies which require DFS. The compromise is we must
also enforce passive scanning and disallow usage of a mode of
operation that beacons: (AP | IBSS | Mesh)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables active scan and beaconing on Channels 1 through 11
on the static world regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers that agree on regulatory to share their
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was never happening but it was still wrong, so correct it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Truth of the matter this was confusing people so mark it as
unlikely as that is the case now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not protecting last_request there is a small possible race
between an 11d hint and another routine which calls reset_regdomains()
which can prevent a valid country IE from being processed. This is
not critical as it will still be procesed soon after but locking prior
to it is correct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so later on we can move the pending requests onto a
workqueue. By using the wiphy_idx instead of the wiphy we can
later easily check if the wiphy has disappeared or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling kobject_uevent_env() can fail mainly due to out of
memory conditions. We do not want to continue during such
conditions so propagate that as well instead of letting
cfg80211 load as if everything is peachy.
Additionally lets clarify that when CRDA is not called during
cfg80211's initialization _and_ if the error is not an -ENOMEM
its because kobject_uevent_env() failed to call CRDA, not because
CRDA failed. For those who want to find out why we also let you
do so by enabling the kernel config CONFIG_CFG80211_REG_DEBUG --
you'll get an actual stack trace.
So for now we'll treat non -ENOMEM kobject_uevent_env() failures as
non fatal during cfg80211's initialization.
CC: Greg KH <greg@kroah.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the core hint path more readable and allows for us to
later make it obvious under what circumstances we need locking or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 is built into the kernel there is perhaps a small
time window betwen nl80211_init() and regulatory_init() where
cfg80211_regdomain hasn't yet been initialized to let the
wireless core do its work. During that rare case and time
frame (if its even possible) we don't allow user regulatory
changes as cfg80211 is working on enabling its first regulatory
domain.
To check for cfg80211_regdomain we now contend the entire operation
using the cfg80211_mutex.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_drv_mutex is protecting more than the driver list,
this renames it and documents what its currently supposed to
protect.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will later be used by others, for now make use of it in
cfg80211_drv_by_wiphy_idx() to return early if an invalid
wiphy_idx has been provided.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes it clearer to read when comparing to ifidx
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a generic commit() function which initiate a
new network joining process. It should be called after some interface
config changes, so that the changes get applied more cleanly. Currently
set_ssid() and set_bssid() call it. Others can be added in future
patches.
In version 1 the header files was forgotten, sorry.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds optional notifier functions for software scan.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch made cfg80211 generally aware of the signal
type a given hardware will give, so now it can implement
SIOCGIWRANGE itself, removing more wext stuff from mac80211.
Might need to be a little more parametrized once we have
more hardware using cfg80211 and new hardware capabilities.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It wasn't a good idea to make the signal type a per-BSS option,
although then it is closer to the actual value. Move it to be
a per-wiphy setting, update mac80211 to match.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no particular reason to not let untrusted users see
this information -- it's just the stations we're talking to,
packet counters for them and possibly some mesh things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to various bugs in the software stack we end up having
to fill qual.qual; level should be used, but wpa_supplicant
doesn't properly ignore qual.qual, NM should use qual.level
regardless of that because qual.qual is 0 but doesn't handle
IW_QUAL_DBM right now.
So fill qual.qual with the qual.level value clamped to
-110..-40 dBm or just the regular 'unspecified' signal level.
This requires a mac80211 change to properly announce the
max_qual.qual and avg_qual.qual values.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanned BSS entries are timestamped with jiffies, which doesn't
increment across suspend and hibernate. On resume, every BSS in the
scan list looks like it was scanned within the last 10 seconds,
irregardless of how long the machine was actually asleep. Age scan
results on resume with the time spent during sleep so userspace has a
clue how old they really are.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX packet counters are needed to fill in RADIUS Accounting
attributes Acct-Output-Packets and Acct-Input-Packets. We already
collect the needed information, but only the TX/RX bytes were
previously exposed through nl80211. Allow applications to fetch the
packet counters, too, to provide more complete support for accounting.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This extends the NL80211_CMD_TRIGGER_SCAN command to allow applications
to specify a set of information element(s) to be added into Probe
Request frames with NL80211_ATTR_IE. This provides support for the
MLME-SCAN.request primitive parameter VendorSpecificInfo and can be
used, e.g., to implement WPS scanning.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add empty function for case of CONFIG_NL80211=n:
net/wireless/scan.c:35: error: implicit declaration of function 'nl80211_send_scan_aborted'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP can switch dynamically between 20/40 Mhz channel width,
in which case we switch the local operating channel, but the
rate control algorithm is not notified. This patch adds a new callback
to indicate such changes to the RC algorithm.
Currently, HT channel width change is notified, but this callback
can be used to indicate any new requirements that might come up later on.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits out the ibss code and data from managed (station) mode.
The reason to do this is to better separate the state machines, and have
the code be contained better so it gets easier to determine what exactly
a given change will affect, that in turn makes it easier to understand.
This is quite some churn, especially because I split sdata->u.sta into
sdata->u.mgd and sdata->u.ibss, but I think it's easier to maintain that
way. I've also shuffled around some code -- null function sending is only
applicable to managed interfaces so put that into that file, some other
functions are needed from various places so put them into util, and also
rearranged the prototypes in ieee80211_i.h accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware with AMPDU queues currently has broken aggregation.
This patch fixes it by making all A-MPDUs go over the regular AC queues,
but keeping track of the hardware queues in mac80211. As a first rough
version, it actually stops the AC queue for extended periods of time,
which can be removed by adding buffering internal to mac80211, but is
currently not a huge problem because people rarely use multiple TIDs
that are in the same AC (and iwlwifi currently doesn't operate as AP).
This is a short-term fix, my current medium-term plan, which I hope to
execute soon as well, but am not sure can finish before .30, looks like
this:
1) rework the internal queuing layer in mac80211 that we use for
fragments if the driver stopped queue in the middle of a fragmented
frame to be able to queue more frames at once (rather than just a
single frame with its fragments)
2) instead of stopping the entire AC queue, queue up the frames in a
per-station/per-TID queue during aggregation session initiation,
when the session has come up take all those frames and put them
onto the queue from 1)
3) push the ampdu queue layer abstraction this patch introduces in
mac80211 into the driver, and remove the virtual queue stuff from
mac80211 again
This plan will probably also affect ath9k in that mac80211 queues the
frames instead of passing them down, even when there are no ampdu queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently assumes init_net for all interfaces,
so really will not cope well with network namespaces,
at least at this time.
To change this, we would have keep track of the netns
in addition to the ifindex, which is not something I
want to think about right now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible that some broken AP might send HT IEs in it's
assoc response even though the STA has not sent them in assoc req
when WEP/TKIP is used as pairwise cipher suite. Also it is important
to check this bit before enabling ht mode in beacon receive path.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drr_change_class lacks a check for NULL of tca[TCA_OPTIONS], so oops
is possible.
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RDS Kconfig and Makefile, and modify net/'s to add
us to the build.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although most of IB and iWARP are separated from each other,
there is some common code required to handle their shared
CM listen port. This code listens for CM events and then
dispatches the event to the appropriate transport, either
IB or iWARP.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for iWARP NICs is implemented as a separate
RDS transport from IB. The code, however, is very
similar to IB (it was forked, basically.) so let's keep
it in one changeset.
The reason for this duplicationis that despite its similarity
to IB, there are a number of places where it has different
semantics. iwarp zcopy support is still under development,
and giving it its own sandbox ensures that IB code isn't
disrupted while iwarp changes. Over time these transports
will re-converge.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Header parsing, ring refill. It puts the incoming data into an
rds_incoming struct, which is passed up to rds-core.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specific to IB is a credits-based flow control mechanism, in
addition to the expected usage of the IB API to package outgoing
data into work requests.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers as an RDS transport and an IB client, and uses IB CM
API to allocate ids, queue pairs, and the rest of that fun stuff.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some transports may support RDMA features. This handles the
non-transport-specific parts, like pinning user pages and
tracking mapped regions.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving a datagram from the transport, RDS parses the
headers and potentially queues an ACK.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parsing of newly-received RDS message headers (including ext.
headers) and copy-to/from-user routines.
page.c implements a per-cpu page remainder cache, to reduce the
number of allocations needed for small datagrams.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS exposes a few tunable parameters via sysctls.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple rds transport to handle loopback connections.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While arguably the fact that the underlying transport needs a
connection to convey RDS's datagrame reliably is not important
to rds proper, the transports implemented so far (IB and TCP)
have both been connection-oriented, and so the connection
state machine-related code is in the common rds code.
This patch also includes several work items, to handle connecting,
sending, receiving, and shutdown.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS currently generates a lot of stats that are accessible via
the rds-info utility. This code implements the support for this.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS supports multiple transports. While this initial submission
only supports Infiniband transport, this abstraction allows others
to be added. We're working on an iWARP transport, and also see
UDP over DCB as another possibility.
This code handles transport registration.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS handles per-socket congestion by updating peers with a complete
congestion map (8KB). This code keeps track of these maps for itself
and ones received from peers.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS's main data structure definitions and exported functions.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RDS (Reliable Datagram Sockets) interface.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute functions with __acquires(...) resp. __releases(...).
Fix this sparse warnings:
net/wanrouter/wanproc.c:82:13: warning: context imbalance in 'r_start' - wrong count at exit
net/wanrouter/wanproc.c:103:13: warning: context imbalance in 'r_stop' - unexpected unlock
net/wanrouter/wanmain.c:765:13: warning: context imbalance in 'lock_adapter_irq' - wrong count at exit
net/wanrouter/wanmain.c:771:13: warning: context imbalance in 'unlock_adapter_irq' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute function with __releases(...)
Fix this sparse warning:
net/ipv4/inet_fragment.c:276:35: warning: context imbalance in 'inet_frag_find' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Remove redundant variable declarations, resp. rename
inner scope variable.
Fix this sparse warnings:
net/decnet/af_decnet.c:1252:40: warning: symbol 'skb' shadows an earlier one
net/decnet/af_decnet.c:1223:24: originally declared here
net/decnet/af_decnet.c:1582:29: warning: symbol 'val' shadows an earlier one
net/decnet/af_decnet.c:1527:22: originally declared here
net/decnet/dn_dev.c:687:21: warning: symbol 'err' shadows an earlier one
net/decnet/dn_dev.c:670:13: originally declared here
net/decnet/sysctl_net_decnet.c:182:21: warning: symbol 'len' shadows an earlier one
net/decnet/sysctl_net_decnet.c:173:16: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute functions with __acquires(...) resp. __releases(...).
Fix this sparse warnings:
net/decnet/dn_dev.c:1324:13: warning: context imbalance in 'dn_dev_seq_start' - wrong count at exit
net/decnet/dn_dev.c:1366:13: warning: context imbalance in 'dn_dev_seq_stop' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Include header file.
Fix this sparse warning:
net/core/sysctl_net_core.c:123:32: warning: symbol 'net_core_path' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Use 'static const char[]' instead of 'static char[]', and
since the data is const now it can be placed in __initconst.
Fix this warning:
net/appletalk/ddp.c: In function 'atalk_init':
net/appletalk/ddp.c:1894: warning: format not a string literal and no format arguments
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Trust in the comment and add '__force' to the cast.
Fix this sparse warning:
net/9p/trans_fd.c:420:34: warning: cast adds address space to expression (<asn:1>)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Attribute function with __acquires(...) resp. __releases(...).
Fix this sparse warnings:
net/802/tr.c:492:21: warning: context imbalance in 'rif_seq_start' - wrong count at exit
net/802/tr.c:519:13: warning: context imbalance in 'rif_seq_stop' - unexpected unlock
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace pairing code can be simplified if it doesn't have to fall
back to using L2CAP_LM in the case of L2CAP raw sockets. This patch
allows the BT_SECURITY socket option to be used for these sockets.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
