* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
Update a couple of S3C24XX and S3C2412 files that are still
using the GPIO number to register mapping calls to get the
s3c_gpio_chip and use the base field from that.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start cleaning up the numbering of GPIO banks by removing the old
bank start definitions currently being used by some of the header
files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The address ben@fluff.org is old, ben-linux@fluff.org has been in use
for a long time, and we should fixup all the occasions of the older
address to avoid confusion.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add arch/arm/mach-s3c2416 for support of the Samsung S3C2416 SoC.
This patch adds support of the S3C2416 SoC, clocks, timers,
and initial IRQ support (without support of secondary set of registers).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
[ben-linux@fluff.org: removed files to be reworked, fixed conflicts]
[ben-linux@fluff.org: use s3c2443 reset instead of specific reset code]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C DMA API doesn't make use of hw_addr.to/from and also
the FIFO addresses are provided from the I2S drivers. So these
fields are redundant.
This patch removes the hw_addr.to/from fields for I2S and the
inclusion of header, paving way for the header to be moved closer
to the I2S controller drivers.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The s3c_gpio_cfgpin() call should be functionally equivalent, so replace
the s3c2410_gpio_cfgpin() calls in the s3c24xx code with s3c_gpio_cfgpin
to allow moving away from a fixed GPIO number to register address mapping
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change mach-jive to use gpiolib for the GPIO lines that are directly
manipulated by it.
Note, we ignore any errors from gpio_request(), unlikely to see any.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
dma-plat.h is the last file left in plat-s3c64xx, but to remove it we
must also change the use of dma-plat.h by the core code and the s3c24xx
implementation.
Rename the s3c24xx dma-plat.h in the common plat-samsung directory as it
may be used for other ports. Move the specific dma bits into the
mach-s3c64xx directory and update the build as needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare for the forthcoming device changes by renaming s3c_device_usb to
s3c_device_ohci as this is what the device represents.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reduce the size of struct clk by 12 bytes and make defining clocks with
common implementation functions easier by moving the set_rate, get_rate,
round_rate and set_parent calls into a new structure called 'struct clk_ops'
and using that instead.
This change does make a few clocks larger as they need their own clk_ops,
but this is outweighed by the number of clocks with either no ops or having
a common set of ops.
Update all the users of this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A number of machines that need s3c_device_nand present do not select
this in their Kconfig entries. Add the necessary selection of the
configuration S3C_DEV_NAND so that we avoid the following error:
arch/arm/mach-s3c2410/built-in.o: In function `bast_map_io':
arch/arm/mach-s3c2410/mach-bast.c:634: undefined reference to `s3c_device_nand'
arch/arm/mach-s3c2412/built-in.o: In function `s3c2412_init_uarts':
arch/arm/mach-s3c2412/s3c2412.c:109: undefined reference to `s3c_device_nand'
arch/arm/mach-s3c2412/built-in.o: In function `jive_machine_init':
arch/arm/mach-s3c2412/mach-jive.c:673: undefined reference to `s3c_device_nand'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add debugfs support for the cpufreq driver to allow
information about the system state to be exported to
the user.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the mapping of the memory controler registers and
add the missing definitions of the register block for the
SSMC.
The register contents definitions can be found in the pl093
header.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.
The following perl was used to change the files:
perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The alterations to the suspend code missed adding a
call to the cache flushing routines during the suspend
path of the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The <mach/dma.h> is for the driver API for the DMA system and should
not have anything relying on the CPU specific registers.
Remove the registers to <plat/dma-regs.h> for the code that really
needs to know about them.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the platform dma.h to dma-plat.h to ensure it doen't get
confused with plat/dma.h
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'jive_vgg2432a4_display' and 'jive_lcd_config' static as
they are not exported, and are generating the following sparse
warnings:
mach-jive.c:280:26: warning: symbol 'jive_vgg2432a4_display' was not declared. Should it be static?
mach-jive.c:313:28: warning: symbol 'jive_lcd_config' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rename s3c2410_cpu_resume to s3c_cpu_resume and s3c2410_cpu_save to
s3c_cpu_save to remove the CPU specific naming of these functions
which are now in the generic PM code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since we have moved a large proportion of the PM code to the common
support area, remove the cpu specific name from the initialisation
function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving the PM code by moving all the common support functions
to a common location in arch/arm/plat-s3c. With the move we rename
the functions from s3cxxx_ to s3c_ to fit the new location.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the IIS headers to their correct place.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As per Russell King's last review comment, find and remove
all unnecessary includes of <linux/delay.h> in the files
that do not need them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the name of the driver, as well as the fact we are not
passing the number of chipselects to the driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX timer is running at the wrong rate due to the
assumptions made in the timer initialisation about the way
the pwm dividers work. This means that time on the S3C64XX
runs twice as fast as it should.
Fix the problem by moving to using the clk framework to setup
the pwm timer clock muxes, as the pwm-clock code has all the
necessary knowledge of how the timer clock inputs are routed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial clocks definitions for the s3c6400
and s3c6410. Move the epll and ext clock from the
s3c2443 support into the common code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the clock settings on resume for suspend/resume
support so that if the boot loader changes anything or
the system's PLL is reset then we return with the correct
settings.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the PLL calculation code into it's own header
file for re-use with the other plat-s3c24xx based
systems such as the S3C24A0.
Note, we change the name of s3c2410_get_pll to the
more generically named s3c24xx_get_pll as well as
the related defintions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
