If the sfc driver is in legacy interrupt mode (either explicitly by
using interrupt_mode module param or by falling back to it) it will
hit a warning at kernel/irq/manage.c because it will try to free an irq
which wasn't allocated by it in the first place because the MSI(X) irqs are
zero and it'll try to free them unconditionally. So fix it by checking if
we're in legacy mode and freeing the appropriate irqs.
CC: Zenghui Shi <zshi@redhat.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: David S. Miller <davem@davemloft.net>
Fixes: 1899c111a5 ("sfc: Fix IRQ cleanup in case of a probe failure")
Reported-by: Zenghui Shi <zshi@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.
Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.
For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.
efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.
The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others. Thus, it uses separate logic.
Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the "separate_tx_channels=1" module parameter, the TX queues are
initially numbered starting from the first TX-only channel number (after all the
RX-only channels). efx_set_channels() renumbers the queues so that they are
indexed from zero.
On EF10, the TX queues need to be relabelled in this way before calling the
dimension_resources NIC type operation, otherwise the TX queue PIO buffers can be
linked to the wrong VIs when using "separate_tx_channels=1".
Added comments to explain UC/WC mappings for PIO buffers
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster than memcpy/memset on some architectures.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: linux-net-drivers@solarflare.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove trailing blank lines in several files.
Use only one blank line between functions.
Add a blank line as a separator in a few places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use 'Solarstorm' or 'Solarflare Communications' in full
any more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions such as is_valid_ether_addr() expect u8 *, so use that
instead of char *.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate efx_channel structures with kzalloc() so we don't need to
zero-initialise individual fields in efx_probe_channel(). Further,
this function will be called again during DMA ring resizing and we
should not reset any statistics then.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF10 implements option descriptors to switch TX checksum offload
on and off between packets. We could therefore use a single
hardware TX queue per kernel TX queue, although we don't yet.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These DMA descriptor types will only be used by the userland
networking stack.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined then NET_IP_ALIGN
will be defined as 0, so this macro is redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is substantial latency in generation and handling of PPS events
from the NIC, which we have to correct for before passing a host
timestamp to the PPS subsystem. We compare clocks with the MC,
giving us two offsets to subtract from the timestamp generated by
pps_get_ts():
(a) Time from the last good sync (where we got host and NIC timestamps
for nearly the same instant) to the time we called pps_get_ts()
(b) Time from NIC top of second to the last good sync
We currently calculate (a) + (b) in a quite confusing way.
Instead, calculate (a) completely, then add (b) to it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conventional net_ratelimit() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ee45fd92c7 ("sfc: Use TX PIO
for sufficiently small packets") introduced the following warning:
drivers/net/ethernet/sfc/tx.c: In function 'efx_enqueue_skb':
drivers/net/ethernet/sfc/tx.c:432:1: warning: label 'finish_packet' defined but not used
Stick the label inside the same #ifdef that the code which calls
it uses. Note that this is only seen for arch that do not set
ARCH_HAS_IOREMAP_WC, such as arm, mips, sparc, ..., as the others
enable the write combining code and hence use the label.
Cc: Jon Cooper <jcooper@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a workaround for a hardware erratum in the SFC9100 family
(SF bug 35388), the TX_DESC_UPD_DWORD register address is also used
for communicating with the event block, and only descriptor pointer
values < 2048 are valid.
If the TX DMA ring size is increased to 4096 descriptors (which the
firmware still allows) then we may write a descriptor pointer
value >= 2048, which has entirely different and undesirable effects!
Limit the TX DMA ring size correctly when this workaround is in
effect.
Fixes: 8127d661e7 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow I transposed these two while bringing the original statistics
support upstream.
Fixes: 99691c4ac1 ('sfc: Add PTP counters to ethtool stats')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_RESET MC command was NOP in the ef10 firmware hence we are using
ENTITY_RESET to make sure all resource allocations are reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/sfc/falcon.c:2601:6: warning:
symbol 'falcon_pull_nic_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Miscellaneous changes for 3.14:
1. Add more information to some WARN messages.
2. Refactor pushing of RSS configuration, from Andrew Rybchenko.
3. Refactor handling of automatic (device address list) vs manual (RX
NFC) MAC filters.
4. Implement clearing of manual RX filters on EF10 when ntuple offload
is disabled.
5. Remove definitions that are unused since the RX buffer allocation
changes, from Andrew Rybchenko.
6. Improve naming of some statistics, from Shradha Shah.
7. Add statistics for PTP support code.
8. Fix insertion of RX drop filters on EF10.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When we insert an filter, the firmware checks that the given RX queue
index is in range even if it will not be used. In case we're
inserting a drop filter, pass the value 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings says:
====================
1. Change PTP clock name to 'sfc'.
2. Complete support for hardware timestamping and PTP clock on the
SFC9100 family.
3. Various cleanups for the PTP code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
An assortment of changes for Linux 3.14:
1. Merge the sfc fixes that you have already merged into net.git.
(The branch point for those was such that this does not bring in any
other changes.)
2. Reduce log level for a generally useless warning message, from
Robert Stonehouse.
3. Include BISTs in ethtool offline self-test for EF10 and recover from
BISTs initiated through other functions, from Jon Cooper.
4. Improve a sanity check on RX completions.
5. Avoid incrementing RX dropped count while the interface is down, from
Jon Cooper.
6. Improve hardware sensor naming and log messages, from Edward Cree.
7. Log all unexpected errors returned by firmware, from Edward Cree.
8. Expose another NVRAM partition to userland.
9. Some refactoring of the PTP code in preparation for EF10 support.
10. Various minor cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These were implemented by Andrew Jackson and Laurence Evans but not
previously included in-tree.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The operation can now fail, so change its return type to int.
Remove the inline wrapper while we're changing the signature.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently a higher priority client can remove a lower priority
client's filter with equal match-expression. This might happen if (a)
the higher priority client has a double-free bug, or (b) another
client with sufficient priority replaced and then removed an equal
filter, allowing the low priority client to insert an equal filter.
In neither case does it actually make sense to carry out the removal;
we should say the filter doesn't exist, as the filter currently
present is not the one that the high-priority client is referring to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Change all the 'stack' naming to 'auto' (or other meaningful term);
the device address list is based on more than just what the network
stack wants, and the no-match filters aren't really what the stack
wants at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MAC filters inserted automatically by the driver, based on the device
address list (EF10) or no-match filters (Siena), should be overridable
at MANUAL or REQUIRED priority. Currently they themselves have
REQUIRED priority and this requires some odd special-casing.
We also can't reliably tell whether such a MAC filter has or has
not been overridden. We just remember that it is wanted by the
stack (RX_STACK flag).
Add another priority level, AUTO, between HINT and MANUAL, and
use this for the automatic filters while they have not been
overridden. Remove the RX_STACK flag. Add an RX_OVER_AUTO
flag which is set only when an AUTO filter has been overridden
(or was requested to be inserted while a higher-priority filter
existed).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 implementation already does this, and it makes more logical
sense to group the RSS hash key and indirection table together.
Rename the operation to rx_push_rss_config.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
In case of certain hardware and firmware errors it can be useful to
have more context than just the file and line number.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The SFC9100 family has only one clock per controller, shared by all
functions. Therefore only create a clock device under the primary
function, and make all other functions refer to the primary's clock
device.
Since PTP functionality is limited to port 0 and PF 0 on the earlier
SFN[56]322F boards, and we also set the primary flag for that
function, we can make the creation of a clock device conditional only
on this flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The primary function of an EF10 controller will share its clock
device with other functions in the same domain (which we call
secondary functions). To this end, we need to associate functions
on the same controller.
We do not control probe order, so allow primary and secondary
functions to appear in any order. Maintain global lists of all
primary functions and of unassociated secondary functions,
and a list of secondary functions on each primary function.
Use the VPD serial number to tell whether functions are part of the
same controller. VPD will not be readable by virtual functions, so
this may need to be revisited later.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 firmware can optionally insert RX timestamps in the packet
prefix. These only include the clock minor value. We must also
enable periodic time sync events on each event queue which provide
the high bits of the clock value.
[bwh: Combined and rebased several changes.
Added the above description and some sanity checks for inline vs
separate timestamps.
Changed efx_rx_skb_attach_timestamp() to read the packet prefix
from the skb head area.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We can potentially pull the entire packet contents into the head area
and then free the page it was in. In order to read an inline
timestamp safely, we need to copy the prefix into the head area as
well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
I added efx_ptp_get_mode() to avoid moving the definition for
efx_ptp_data, since the current PTP mode is needed for
siena.c:siena_set_ptp_hwtstamp.
[bwh: Also move the rx_filters mask, and add kernel-doc]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
