Rework DAI format calculation in preparation for adding more formats
later. As a side-effect this enables all CBM/CBS x CFM/CFS combinations
for supported formats. (Note: the additional modes are not tested.)
Note: this changes FSEDGE to POSITIVE for I2S CBM_CFS mode as the TXSYN
interrupt is not used anyway.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/f5949b0326fdcdca072f3ed03f77de9e207631cd.1566677788.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow SSC to be used on platforms described using audio-graph-card
in Device Tree.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/233d5461f4448df151755de7b69a0cd3ad310d5c.1566677788.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
This controller supports capture and playback running at the same time,
with the limitation that both capture and playback must be configured the
same way (sample rate, sample format, number of channels, etc). For this,
we have to assure that the configuration registers look the same when
capture and playback are initiated.
This patch fixes a bug in which the controller is in master mode and the
hw_params() callback fails for the second audio stream. The fail occurs
because the divisors are calculated after comparing the configuration
registers for capture and playback. The fix consists in calculating the
divisors before comparing the configuration registers. BCLK and LRC are
then configured and started only if the controller is not already running.
Fixes: 7e0cdf545a55 ("ASoC: mchp-i2s-mcc: add driver for I2SC Multi-Channel Controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20190820162411.24836-4-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since hw_free() can be called multiple times and not just after a stop
trigger command, we should check whether the RX or TX ready interrupt was
truly enabled previously. For this, we assure that the condition of the
wait event is always true, except when RX/TX interrupts are enabled.
Fixes: 7e0cdf545a55 ("ASoC: mchp-i2s-mcc: add driver for I2SC Multi-Channel Controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20190820162411.24836-3-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If hw_free() gets called after hw_params(), GCLK remains prepared,
preventing further use of it. This patch fixes this by unpreparing the
clock in hw_free() or if hw_params() gets an error.
Fixes: 7e0cdf545a55 ("ASoC: mchp-i2s-mcc: add driver for I2SC Multi-Channel Controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20190820162411.24836-2-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-50-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 655368dfc7 ("ASoC: atmel: tse850-pcm5142: don't select
unnecessary Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 655368dfc7 ("ASoC: atmel: tse850-pcm5142: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit ced5b08020 ("ASoC: atmel: sam9x5_wm8731: don't select unnecessary
Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit ced5b08020 ("ASoC: atmel: sam9x5_wm8731: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit bfc7938e58 ("ASoC: atmel: sam9g20_wm8731: don't select
unnecessary Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit bfc7938e58 ("ASoC: atmel: sam9g20_wm8731: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 318ebbe806 ("ASoC: atmel: mikroe-proto: don't select unnecessary
Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 318ebbe806 ("ASoC: atmel: mikroe-proto: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3609750e9d ("ASoC: atmel: atmel_wm8904: don't select
unnecessary Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 3609750e9d ("ASoC: atmel: atmel_wm8904: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 7baf32e164 ("ASoC: atmel: atmel-pdmic: don't select unnecessary
Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 7baf32e164 ("ASoC: atmel: atmel-pdmic: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 02602401e5 ("ASoC: atmel: atmel-classd: don't select
unnecessary Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 02602401e5 ("ASoC: atmel: atmel-classd: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_dmaengine_pcm_register,
let's use it.
This patch also removes related empty functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.654888175@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 or
later as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.848507137@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warnings:
sound/soc/atmel/tse850-pcm5142.c:120:5: warning: symbol 'tse850_get_mix' was not declared. Should it be static?
sound/soc/atmel/tse850-pcm5142.c:132:5: warning: symbol 'tse850_put_mix' was not declared. Should it be static?
sound/soc/atmel/tse850-pcm5142.c:154:5: warning: symbol 'tse850_get_ana' was not declared. Should it be static?
sound/soc/atmel/tse850-pcm5142.c:187:5: warning: symbol 'tse850_put_ana' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Inter-IC Sound Controller (I2SMCC) provides a 5-wire, bidirectional,
synchronous, digital audio link to external audio devices: I2SMCC_DIN,
I2SMCC_DOUT, I2SMCC_WS, I2SMCC_CK, and I2SMCC_MCK pins.
The I2SMCC complies with the Inter-IC Sound (I2S) bus specification and
supports a Time Division Multiplexed (TDM) interface with external
multi-channel audio codecs.
The I2SMCC consists of a receiver, a transmitter and a common clock
generator that can be enabled separately to provide Master, Slave or
Controller modes with receiver and/or transmitter active.
DMA Controller channels, separate for the receiver and for the transmitter,
allow a continuous high bit rate data transfer without processor
intervention to the following:
- Audio CODECs in Master, Slave, or Controller mode
- Stereo DAC or ADC through a dedicated I2S serial interface
- Multi-channel or multiple stereo DACs or ADCs, using the TDM format
This IP is embedded in Microchip's new sam9x60 SoC.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the MikroElektronika PROTO audio codec board.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to // comments in the leading comment, drop the boilerplate
license text and use the correct MODULE_LICENSE.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generated clock (gclk) driver is able to set aclk as its parent and
change its rate alone, if needed. This means that our driver no longer
needs to configure aclk and we can let gclk select and configure its
clock source.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Atmel I2S controller embedded into
sama5d2x SoCs.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in pr_debug message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an error message within devm_ioremap_resource already,
so remove the redundant dev_err() call.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
To avoid complex operation, this patch adds device pointer
to atmel_classd.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_err already provides messages with prefix, so drop 'ASoC'
prefix.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_*() logging functions instead of plain printk and as
messages are now properly prefixed drop 'ASoC' prefix as well.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_ATMEL_SOC_CLASSD selects SND_ATMEL_SOC_DMA but the driver itself
handles its own DMA operations and doesn't need anything from
atmel-pcm-dma.c or atmel_ssc_dai.c.
Replace SND_ATMEL_SOC_DMA by SND_SOC_GENERIC_DMAENGINE_PCM which is the
only one actually required.
This may end up in a configuration leading to a link error:
sound/soc/atmel/atmel_ssc_dai.o: In function `atmel_ssc_set_audio':
atmel_ssc_dai.c:(.text+0x79c): undefined reference to `atmel_pcm_dma_platform_register'
atmel_ssc_dai.c:(.text+0x79c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `atmel_pcm_dma_platform_register'
sound/soc/atmel/atmel_ssc_dai.o: In function `atmel_ssc_put_audio':
atmel_ssc_dai.c:(.text+0xf24): undefined reference to `atmel_pcm_dma_platform_unregister'
atmel_ssc_dai.c:(.text+0xf24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `atmel_pcm_dma_platform_unregister'
Tested on sama5d2 xplained with the following configuration
where nothing selects SND_ATMEL_SOC_DMA:
CONFIG_SND_ATMEL_SOC=y
CONFIG_SND_ATMEL_SOC_CLASSD=y
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e0a25b6d18 ("ASoC: atmel-classd: add the Audio Class D Amplifier")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
This driver is using .get_regmap and set regmap by using
dev_get_regmap(), but it is automatically done by
snd_soc_component_add_unlocked(). let's remove .get_regmap.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the sunxi-ng framework. Otherwise, the heavy hitters are various drivers
for SoCs like AT91, Amlogic, Renesas, and Rockchip. There are some other
new clk drivers in here too but overall this is just a bunch of clk
drivers for various different pieces of hardware and a collection of
non-critical fixes for clk drivers.
New Drivers:
- Allwinner R40 SoCs
- Renesas R-Car Gen3 USB 2.0 clock selector PHY
- Atmel AT91 audio PLL
- Uniphier PXs3 SoCs
- ARC HSDK Board PLLs
- AXS10X Board PLLs
- STMicroelectronics STM32H743 SoCs
Removed Drivers:
- Non-compiling mb86s7x support
Updates:
- Allwinner A10/A20 SoCs converted to sunxi-ng framework
- Allwinner H3 CPU clk fixes
- Renesas R-Car D3 SoC
- Renesas V2H and M3-W modules
- Samsung Exynos5420/5422/5800 audio fixes
- Rockchip fractional clk approximation fixes
- Rockchip rk3126 SoC support within the rk3128 driver
- Amlogic gxbb CEC32 and sd_emmc clks
- Amlogic meson8b reset controller support
- IDT VersaClock 5P49V5925/5P49V6901 support
- Qualcomm MSM8996 SMMU clks
- Various 'const' applications for struct clk_ops
- si5351 PLL reset bugfix
- Uniphier audio on LD11/LD20 and ethernet support on LD11/LD20/Pro4/PXs2
- Assorted Tegra clk driver fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0JbT
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The diff is dominated by the Allwinner A10/A20 SoCs getting converted
to the sunxi-ng framework. Otherwise, the heavy hitters are various
drivers for SoCs like AT91, Amlogic, Renesas, and Rockchip. There are
some other new clk drivers in here too but overall this is just a
bunch of clk drivers for various different pieces of hardware and a
collection of non-critical fixes for clk drivers.
New Drivers:
- Allwinner R40 SoCs
- Renesas R-Car Gen3 USB 2.0 clock selector PHY
- Atmel AT91 audio PLL
- Uniphier PXs3 SoCs
- ARC HSDK Board PLLs
- AXS10X Board PLLs
- STMicroelectronics STM32H743 SoCs
Removed Drivers:
- Non-compiling mb86s7x support
Updates:
- Allwinner A10/A20 SoCs converted to sunxi-ng framework
- Allwinner H3 CPU clk fixes
- Renesas R-Car D3 SoC
- Renesas V2H and M3-W modules
- Samsung Exynos5420/5422/5800 audio fixes
- Rockchip fractional clk approximation fixes
- Rockchip rk3126 SoC support within the rk3128 driver
- Amlogic gxbb CEC32 and sd_emmc clks
- Amlogic meson8b reset controller support
- IDT VersaClock 5P49V5925/5P49V6901 support
- Qualcomm MSM8996 SMMU clks
- Various 'const' applications for struct clk_ops
- si5351 PLL reset bugfix
- Uniphier audio on LD11/LD20 and ethernet support on LD11/LD20/Pro4/PXs2
- Assorted Tegra clk driver fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (120 commits)
clk: si5351: fix PLL reset
ASoC: atmel-classd: remove aclk clock
ASoC: atmel-classd: remove aclk clock from DT binding
clk: at91: clk-generated: make gclk determine audio_pll rate
clk: at91: clk-generated: create function to find best_diff
clk: at91: add audio pll clock drivers
dt-bindings: clk: at91: add audio plls to the compatible list
clk: at91: clk-generated: remove useless divisor loop
clk: mb86s7x: Drop non-building driver
clk: ti: check for null return in strrchr to avoid null dereferencing
clk: Don't write error code into divider register
clk: uniphier: add video input subsystem clock
clk: uniphier: add audio system clock
clk: stm32h7: Add stm32h743 clock driver
clk: gate: expose clk_gate_ops::is_enabled
clk: nxp: clk-lpc32xx: rename clk_gate_is_enabled()
clk: uniphier: add PXs3 clock data
clk: hi6220: change watchdog clock source
clk: Kconfig: Name RK805 in Kconfig for COMMON_CLK_RK808
clk: cs2000: Add cs2000_set_saved_rate
...
Since gclk (generated-clk) is now able to determine the rate of the
audio_pll, there is no need for classd to have a direct phandle to the
audio_pll while already having a phandle to gclk.
Thus, remove all mentions to aclk in classd driver and update macros and
variable names.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The function platform_set_drvdata copies the value the variable
card to card->dev->driver_data, then the address of &pdev->dev is
assigned to card->dev in atmel_pdmic_asoc_card_init, but when
calling snd_soc_register_card,the function
dev_set_drvdata(card->dev, card) will do the same copy operation,
so i think that the former copy operation can be removed.
Signed-off-by: Peng Donglin <dolinux.peng@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function platform_set_drvdata copies the value the variable
card to card->dev->driver_data, then the address of &pdev->dev is
assigned to card->dev in atmel_classd_asoc_card_init, but when
calling snd_soc_register_card,the function
dev_set_drvdata(card->dev, card) will do the same copy operation,
so i think that the former copy operation can be removed.
Signed-off-by: Peng Donglin <dolinux.peng@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At some point I added the "Low" entry at the beginning of the array
without bumping the enumeration count from 9 to 10. Fix this. While at
it, fix the anti-pattern for the other enumeration (used by MUX{1,2}).
Fixes: aa43112445 ("ASoC: atmel: tse850: add ASoC driver for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The PM functions used in this driver are the ones defined in
sounc/soc/soc-core.c.
When suspending (using snd_soc_suspend), the regcache is marked dirty
but is never synced on resume.
Sync regcache on resume of Atmel ClassD device.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the ifdef conditions with IS_ENABLED() macro.
No functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the audio clock rate according to the datasheet.
Reported-by: Dushara Jayasinghe <dushara@successful.com.au>
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This breaks devicetree compatibility, but in this case that is ok. All
affected units are either on my desk, or running an even older version
of the driver that is not compatible with the upstreamed version anyway
(and when these other units are eventually updated, they will get a
fresh dtb as well, so that is not a significant problem either).
All of that is of course assuming that noone else has managed to build
something that can use this driver, but that seems extremely improbable.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
When this driver masters BCLK and/or LRCLK, and noone has stated
differently, assume that all the bits of a frame are used.
This relieves the cpu dai users from the duty to fill in the dividers for
the common case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
2611 1536 0 4147 1033 sound/soc/atmel/atmel_wm8904.o
2675 1480 0 4155 103b sound/soc/atmel/atmel_wm8904.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_pcm_ops structures that are only stored in the ops field of a
snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit cbaadf0f90 ("ASoC: atmel_ssc_dai: refactor the startup and
shutdown") refactored code such that the SSC is reset on every
startup; this breaks duplex audio (e.g. first start audio playback,
then start record, causing the playback to stop/hang)
Fixes: cbaadf0f90 (ASoC: atmel_ssc_dai: refactor the startup and shutdown)
Signed-off-by: Christoph Huber <c.huber@bct-electronic.com>
Signed-off-by: Peter Meerwald-Stadler <p.meerwald@bct-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add the missing clk_disable_unprepare() before return from
atmel_pdmic_cpu_dai_startup() in the error handling case.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get 1 warning about global functions without a declaration
in the ASoC atmel-pdmic driver when building with W=1:
sound/soc/atmel/atmel-pdmic.c:286:5: warning: no previous prototype for 'pdmic_get_mic_volsw' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static.
so this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
follow-up patch from c706f2e55f ASoC: atmel_ssc_dai: distinguish the
different SSC
cpu_dai id is always 0, use platform_device id to distinguish DMA
parameters of SSCs
Signed-off-by: Peter Meerwald-Stadler <p.meerwald@bct-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to
devm_ioremap_resource.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to
devm_ioremap_resource.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
m32r allmodconfig build is failing with the error:
ERROR: "bad_dma_ops" [sound/soc/atmel/snd-soc-atmel-pcm-pdc.ko] undefined!
The code is using DMA but the related dependency is not mentioned in the
Kconfig.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cpu_dai id always equals 0, can't distinguish the
different SSC. Use platform_device id to record
and distinguish the different SSC.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes the audio play can not be resumed after it is
suspended. Add snd_soc_pm_ops to execute power management
operations, then this issue is fixed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for the Pulse Density Modulation Interface
Controller. It comes with digitallly controlled gain,
a High-Pass and a SINCC filter.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to unregister codec in probe function,
when the error occurs after the codec is registered.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for the digital imput to PWM output stereo
class D amplifier. It comes with filter, digitally
controlled gain, an equalizer and a dmphase filter.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is currently possible to have CONFIG_SND_ATMEL_SOC_SSC=y with either
CONFIG_SND_ATMEL_SOC_PDC=m or CONFIG_SND_ATMEL_SOC_DMA=m. This results in a
driver that compiles but does not link with this kind of error:
sound/built-in.o: In function `atmel_ssc_set_audio':
(.text+0x87d90): undefined reference to `atmel_pcm_pdc_platform_register'
sound/built-in.o: In function `atmel_ssc_put_audio':
(.text+0x8879a): undefined reference to `atmel_pcm_pdc_platform_unregister'
Introduce new config options SND_ATMEL_SOC_SSC_PDC and
SND_ATMEL_SOC_SSC_DMA which should be used by the board drivers and the
correct logic to properly select the SND_ATMEL_SOC_PDC and
SND_ATMEL_SOC_DMA states.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
