Some tests shows that using AMSDU to aggregate TCP ACKs to specific
APs will degrade the throughput on 2.4G band in 20MHz bandwidth
(< 10 Mbps, should be ~100 Mbps for 2x2). Also found that there's
barely no negative impact if we disable TX AMSDU on 2.4G to connect
to other APs. So it seems like we can just tell mac80211 to not to
aggregate MSDUs when transmitting on 2.4G band.
Note that we still can TX AMSDU on 5G band and benefit from it by
having 50 ~ 70 Mbps throughput improvement.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
According to some experiments, the original RF register protection
setting of 8822c cannot perfectly make sure that there is no hardware
PI write (direct) during direct write. Modify the setting so that the
hardware block of PI would be turned off via rtw8822c_rstb_3wire()
during the direct write, to avoid RF register racing.
Note that 8822b uses SIPI write (indirect), so 8822b does not
have such problem.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware value of secondary channel offset isn't very intuitive. This
commit adds enumeration, so we can easier to check the logic with the
suffix of enumeration name, likes _UPPER or _LOWER.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sk_buff structs need to be freed with kfree_skb(), not kfree().
Fixes: b6c12908a3 ("rtw88: Add wowlan net-detect support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Though hardware isn't implement CCMP-256, GCMP and GCMP-256, it's possible
to fallback to use software de-/en-cryption implemented by mac80211.
Without adding these chipers, kernel log will show something if we connect
to a WPA3 enterprise AP, likes
wlan0: failed to set key (1, ff:ff:ff:ff:ff:ff) to hardware (-524)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver could possibly be dead-locked while canceling works with
*_sync() with mutex lock held. Those cancel_delayed_work_sync()
functions will wait until the work is done, but if we hold the
lock, they will never acquire the lock.
To prevent this, simply release the lock and acquire again after
the works have been canceled. And to avoid the works being queued
again, check if the device is at RTW_FLAG_RUNNING state, otherwise
just return and do nothing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver is coming up, mac80211 will set changed as ~0 (0xffffffff),
and driver could enter IDLE state (power off) before switching channel or
other config event. So move rtw_enter_ips() to the last, to make sure the
driver completed the config events before going to IDLE state.
So, moves leave/enter IPS config to be first/last one according to flag
IEEE80211_CONF_IDLE. If there're more configureations we want to add in
the future, they must locate between leave/enter IPS.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since RTL8822CE has enabled reference clock auto calibration,
there is no need to add any clock delay for covering the timing
gap of the reference clock.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
vif is not used, remove it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns that ret is used uninitialzed.
And we found that actually the return type should be "int" instead
of "bool".
Fixes: 44bc17f7f5 ("rtw88: support wowlan feature for 8822c")
Link: https://github.com/ClangBuiltLinux/linux/issues/850
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in one of the fields in the btc_coexist struct,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/dm.c:16:18:
warning: ofdmswing_table defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/dm.c:56:17:
warning: cckswing_table_ch1ch13 defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/dm.c:92:17:
warning: cckswing_table_ch14 defined but not used [-Wunused-const-variable=]
These variable is never used, so remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:15:18:
warning: ofdmswing_table defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:61:17:
warning: cckswing_table_ch1ch13 defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:97:17:
warning: cckswing_table_ch14 defined but not used [-Wunused-const-variable=]
These variable is never used, so remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:142:17:
warning: cckswing_table_ch1ch13 defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:178:17:
warning: cckswing_table_ch14 defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:96:18:
warning: ofdmswing_table defined but not used [-Wunused-const-variable=]
These variable is never used, so remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable cond is being assigned with a value that is never
read, it is assigned a new value later on. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When TX packet arrives, driver should leave deep PS state to make
sure the DMA is working. After requested to leave deep PS state,
driver needs to poll the PS state to check if the mode has been
changed successfully. The driver used to check the state of the
hardware every 20 msecs, which means upon the first failure of
state check, the CPU is delayed 20 msecs for next check. This is
harmful for some time-sensitive applications such as media players.
So, use shorter delay time each check from 20 msecs to 100 usecs.
The state should be changed in several tries. But we still need
to reserve ~15 msecs in total in case of the state just took too
long to be changed successfully. If the states of driver and the
hardware is not synchronized, the power state could be locked
forever, which mean we could never enter/leave the PS state.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the TX queue may be empty and we could possible
dequeue a NULL pointer, crash the kernel. If the skb is NULL
then there is nothing to do, just leave the ISR.
And the TX queue should not be empty here, so print an error
to see if there is anything wrong for DMA ring.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtw88/phy.c:1437:1-24: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of functions which were exposed in sw.h, are only used in sw.c, so
just make them static. This makes sw.h unnecessary, so remove it.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of functions which were exposed in sw.h, are only used in sw.c, so
just make them static. This makes sw.h unnecessary, so remove it.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of functions which were exposed in sw.h, are only used in sw.c, so
just make them static. This makes sw.h unnecessary, so remove it.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It has one define, which is already defined in include from reg.h.
All the declared functions are not implemented anywhere, sw.c has
ones with similar names which are already static.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of functions which were exposed in sw.h, are only used in sw.c, so
just make them static. This makes sw.h unnecessary, so remove it.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It has one define, which is already defined in include from reg.h.
All functions are declared in their own headers and included in *.c
files belonging to them.
This makes sw.h unnecessary, so we can remove it.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of functions which were exposed in sw.h, are only used in sw.c, so
just make them static. The rtl92c_init_var_map function is not defined
anywhere, while declared in sw.h. Two other functions are also declared
in phy.h (which is included in sw.c) and their definitions are in phy.c
Overall sw.h is unnecessary and can be removed.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of functions which were exposed in sw.h, are only used in sw.c, so
just make them static. This makes sw.h unnecessary, so remove it.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace USB_VENDER_ID_REALTEK with USB_VENDOR_ID_REALTEK.
Signed-off-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's more reasonable to define max_num_of_tx_queue() as an inline function.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Should assign NULL to skb after kfree(), in case of driver
trying to free the same skb again.
This could happen if driver failed to allocate an skb when
building reserved page.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix typo, should use rtw_hci_stop()
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As driver can easily get vif with container_of(), we can
just remove it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unused, will not be used neither, because the hardware/firmware
can only support one vif for LPS currnetly. If there's more than
one vif, than driver will never enter LPS. So remove it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
dm_lock is never used. Thus, remove this redundant spinlock.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update card enable power sequence flow, to fix CMD11 fail after
reboot and wrong PLL clock.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX secondary channel offset is valid only if current bandwidth is 80M,
otherwise leave this value as zero. The wrong value of txsc40 causes
MAC unpredictable behavior.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rate mask is used to tell firmware the supported rate depends on
negotiation. We loop 2 times for all VHT/HT 2SS rate mask first, and then
only keep the part according to chip's NSS.
This commit fixes the logic error of '&' operations for VHT/HT rate, and
we should run this logic before adding legacy rate.
To access HT MCS map, index 0/1 represent MCS 0-7/8-15 respectively. Use
NL80211_BAND_xxx is incorrect, so fix it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Net-detect is an option of wowlan to allow the device to
be woken up from suspend mode when configured network is detected.
When user enables net-detect and lets the device enter suspend
state, wowlan firmware will periodically scan until beacon or
probe response of configured networks are received.
Between two scans, wowlan firmware keeps wifi chip in idle mode
to reduce power consumption. If configured networks are detected,
wowlan firmware will trigger resume process.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pattern match is an option of wowlan to allow the device
to be woken up from suspend mode when receiving packets
matched user-designed patterns.
The patterns are written into hardware cam in suspend flow
if users have set up them. If packets matched designed
pattern are received, wowlan firmware will get an interrupt
and then wake up the device.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wake on WLAN(wowlan) is a feature which allows devices
to be woken up from suspend state through wlan events.
When user enables wowlan feature and then let the device
enter suspend state, wowlan firmware will be loaded by
the driver and periodically monitors wifi packets.
Power consumption of wifi chip will be reduced in this
state.
If wowlan firmware detects that specific wlan event
happens, it will issue wakeup signal to trigger resume
process. Driver will load normal firmware and let wifi
chip return to the original state.
Currently supported wlan events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver used to download normal firmware only,
but some devices support wowlan and require to
download wowlan firmware when system suspends.
So modify rtw_load_firmware() and its callback to
allow driver to download both normal and wowlan firmware.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices need to configure interface/HCI related reigsters
in power on flow. Add interface_cfg for HCI for the settings.
The driver only supports RTL8822BE/RTL8822CE now, and since
RTL8822BE does not need to configure PCIE, the configuration
is only added for RTL8822CE. Without it, some of the RTL8822CE
device can crash and disconnected to host in suspend/wowlan mode.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When PCI trx rings are reset, the DMA engine should also be reset.
Otherswise, the rx_tag of rx flow is not synchronous to hw.
Remove DMA reset when rtw_pci_start() as we added it in
rtw_pci_setup().
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When skbs queued for each TX ring are relased in PCI stop flow,
the ring index should be reset at the same time.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92de_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92de_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92c_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92ce_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92ce_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92d_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92c_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
