The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.
Add a local copy using writel/readl accesses to make sure we use the right
memory access width.
The switch to memcpy_to/fromio was done because of 285133040e
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.
Fixes: 103a5348c2 ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been reported that usage of memcpy() to/from an iomem mapping is invalid,
and a recent arm64 memcpy update [1] triggers a memory abort when dram-access-quirk
is used on the G12A/G12B platforms.
This adds a local sg_copy_to_buffer which makes usage of io versions of memcpy
when dram-access-quirk is enabled.
[1] 285133040e ("arm64: Import latest memcpy()/memmove() implementation")
Fixes: acdc8e71d9 ("mmc: meson-gx: add dram-access-quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210609150230.9291-1-narmstrong@baylibre.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The brcmfmac driver can generate a scatterlist from a skb with each packets
not aligned to the block size. This is not supported by the Amlogic Descriptor
dma engine where each descriptor must match a multiple of the block size.
The sg list is valid, since the sum of the sg buffers is a multiple of the
block size, but we must discard those when in SD_IO_RW_EXTENDED mode since
SDIO block mode can be used under the hood even with data->blocks == 1.
Those transfers are very rare, thus can be replaced by a bounce buffer
without real performance loss.
Fixes: 7412dee9f1 ("mmc: meson-gx: replace WARN_ONCE with dev_warn_once about scatterlist size alignment in block mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-2-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some drivers like ath10k can sometimg give an sg buffer with an offset whose alignment
is not compatible with the Amlogic DMA descriptor engine requirements.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in ath10k, but since it's only a performance issue
the warning should be removed.
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode"),
support for SDIO SD_IO_RW_EXTENDED transferts are properly filtered but some driver
like brcmfmac still gives a block sg buffer size not aligned with SDIO block,
triggerring a WARN_ONCE() with scary stacktrace even if the transfer works fine
but with possible degraded performances.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in brcmfmac, but since it's only a performance issue
the warning should be removed.
Fixes: e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210416094347.2015896-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable SGDMA support for SD_IO_RW_EXTENDED and add proper check
for scatterlist size alignment in block mode.
According to documentation, in SDIO block mode meson-gx DMA could
only handle buffers with sizes that are multiples of SDIO block size.
Some SDIO drivers like brcmfmac use scatterlist API, but do not enforce
proper scatterlist buffer size alignemnt, this looks like a root cause
of non-working CMD53.
Some minor style fixes.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201218075312.67338-1-lebed.dmitry@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/mmc/host/meson-gx-mmc.c:1252:34: warning:
‘meson_mmc_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201103163046.14336-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.14 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SDHI drivers
Link: https://lore.kernel.org/r/20200903162412.3.Id1ff21470f08f427aedd0a6535dcd83ccc56b278@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-6-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The actual max_segs computation leads to failure while using the broadcom
sdio brcmfmac/bcmsdh driver, since the driver tries to make usage of
scatter gather.
But with the dram-access-quirk we use a 1,5K SRAM bounce buffer, and the
max_segs current value of 3 leads to max transfers to 4,5k, which doesn't
work.
This patch sets max_segs to 1 to better describe the hardware limitation,
and fix the SDIO functionality with the brcmfmac/bcmsdh driver on Amlogic
G12A/G12B SoCs on boards like SEI510 or Khadas VIM3.
Reported-by: Art Nikpal <art@khadas.com>
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Fixes: acdc8e71d9 ("mmc: meson-gx: add dram-access-quirk")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200608084458.32014-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-3-ulf.hansson@linaro.org
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from the
dma-mapping interface for ARM
- Convert the generic MMC DT doc to YAML schemas
- Drop questionable support for powered-on re-init of SDIO cards at
runtime resume and for SDIO HW reset
- Prevent questionable re-init of powered-on removable SDIO cards at
system resume
- Cleanup and clarify some SDIO core code
MMC host:
- tmio: Make runtime PM enablement more flexible for variants
- tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt to clarify
- sdhci-pci: Add support for Intel EHL
- sdhci-pci-o2micro: Enable support for 8-bit bus
- sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
- sdhci-of-esdhc: Improve clock management and tuning
- sdhci_am654: Enable support for 4 and 8-bit bus on J721E
- sdhci-sprd: Use pinctrl for a proper signal voltage switch
- sdhci-sprd: Add support for HS400 enhanced strobe mode
- sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the clock
- sdhci-sprd: Add support for optional gate clock
- sunxi-mmc: Convert DT doc to YAML schemas
- meson-gx: Add support for broken DRAM access for DMA
MEMSTICK core:
- Fixup error path of memstick_init()
-----BEGIN PGP SIGNATURE-----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=vkWp
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from
the dma-mapping interface for ARM
- Convert the generic MMC DT doc to YAML schemas
- Drop questionable support for powered-on re-init of SDIO cards at
runtime resume and for SDIO HW reset
- Prevent questionable re-init of powered-on removable SDIO cards at
system resume
- Cleanup and clarify some SDIO core code
MMC host:
- tmio: Make runtime PM enablement more flexible for variants
- tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt
to clarify
- sdhci-pci: Add support for Intel EHL
- sdhci-pci-o2micro: Enable support for 8-bit bus
- sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
- sdhci-of-esdhc: Improve clock management and tuning
- sdhci_am654: Enable support for 4 and 8-bit bus on J721E
- sdhci-sprd: Use pinctrl for a proper signal voltage switch
- sdhci-sprd: Add support for HS400 enhanced strobe mode
- sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the
clock
- sdhci-sprd: Add support for optional gate clock
- sunxi-mmc: Convert DT doc to YAML schemas
- meson-gx: Add support for broken DRAM access for DMA
MEMSTICK core:
- Fixup error path of memstick_init()"
* tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
mmc: alcor: remove a redundant greater or equal to zero comparison
mmc: sdhci-msm: fix mutex while in spinlock
mmc: sdhci_am654: Make some symbols static
dma-mapping: remove dma_max_pfn
mmc: core: let the dma map ops handle bouncing
dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
mmc: sdhci-sprd: Add pin control support for voltage switch
dt-bindings: mmc: sprd: Add pinctrl support
mmc: sdhci-sprd: Add start_signal_voltage_switch ops
mmc: sdhci-pci: Add support for Intel EHL
mmc: tmio: Use dma_max_mapping_size() instead of a workaround
mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
mmc: sdio: Turn sdio_run_irqs() into static
mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses the full gnu general public license is included in this
distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.258730266@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Amlogic G12A SoC family, (only) the SDIO controller fails to access
the data from DRAM, leading to a broken controller.
But each MMC controller has 1,5KiB of SRAM after the registers, that can
be used as bounce buffer to avoid direct DRAM access from the integrated
DMAs (this SRAM may be used by the boot ROM when DRAM is not yet initialized).
The quirk is to disable the chained descriptor for this controller, and
use this SRAM memory zone as buffer for the bounce buffer fallback mode.
The performance hit hasn't been evaluated, but the fix has been tested
using a WiFi AP6398S SDIO module, and the iperf3 Bandwidth measurement gave
55.2 Mbits/sec over a 63 Hours long test, with the SDIO ios set as High-Speed
at 50MHz clock. It gave 170 Mbits/sec as SDR104 and 200MHz clock.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While cleaning the ISR of the meson-gx and acking only raised irqs,
the ack of the irq was moved at the very last stage of the function.
This was stable during the initial tests but it triggered issues with
hs200, under specific loads (like booting android). Acking the irqs
after calling the mmc_request_done() causes the problem.
Moving the ack back to the original place solves the issue. Since the
irq is edge triggered, it does not hurt to ack irq even earlier, so
let's do it early in the ISR.
Fixes: 9c5fdb07a2 ("mmc: meson-gx: ack only raised irq")
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Brad Harper <bjharper@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use signal resampling tuning for the UHS and HS200 modes.
Instead of trying to get the *best* resampling setting with complex
window calculation, we just stop on the first working setting.
If the tuning setting later proves unstable, we will just continue the
tuning where we left it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This remove all the code related to phase settings. Using the Rx phase
for tuning has not been reliable. We had several issues over the past
months, on both v2 and v3 mmc chips After discussing the issue matter
with Amlogic, They suggested to set a phase shift of 180 between Core and
Tx and use signal resampling for the tuning.
Since we won't be playing with the phase anymore, let's remove all the
clock code related to it and set the appropriate value on init.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Activating DDR in the Amlogic mmc controller, among other things, will
divide the output clock by 2. So by activating it with clock on, we are
creating a glitch on the output.
Instead, let's deal with DDR when the clock output is off, when setting
the clock.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At the moment, all our attempts to enable HS400 on Amlogic chipsets have
been unsuccessful or unreliable. Until we can figure out how to enable this
mode safely and reliably, let's force it off.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason for another device to request the MMC irq. It should
only be used the MMC device, so remove IRQ_SHARED and replace by
IRQ_ONESHOT as we don't the irq to fire again until the irq thread is
done
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is merely a clean up. It makes sense to only ack raised irqs
instead of acking everything all the time.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is already a function available to poll a register until a
condition is met. Let's use it instead of open coding it.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bb36489032 ("mmc: meson-gx: Free irq in release() callback")
changed the _probe code to use request_threaded_irq() instead of
devm_request_threaded_irq().
Unfortunately this removes a fallback for the interrupt name:
devm_request_threaded_irq() uses the device name as fallback if the
given IRQ name is NULL. request_threaded_irq() has no such fallback,
thus /proc/interrupts shows "(null)" instead.
Explicitly pass the dev_name() so we get the IRQ name shown in
/proc/interrupts again.
While here, also fix the indentation of the request_threaded_irq()
parameter list.
Fixes: bb36489032 ("mmc: meson-gx: Free irq in release() callback")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because the irq was requested through device managed resources API
(devm_request_threaded_irq()) it was freed after meson_mmc_remove()
completion, thus after mmc_free_host() has reclaimed meson_host memory.
As this irq is IRQF_SHARED, while using CONFIG_DEBUG_SHIRQ, its handler
get called by free_irq(). So meson_mmc_irq() was called after the
meson_host memory reclamation and was using invalid memory.
We ended up with the following scenario:
device_release_driver()
meson_mmc_remove()
mmc_free_host() /* Freeing host memory */
...
devres_release_all()
devm_irq_release()
__free_irq()
meson_mmc_irq() /* Uses freed memory */
To avoid this, the irq is released in meson_mmc_remove() and in
mseon_mmc_probe() error path before mmc_free_host() gets called.
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With some eMMC devices, there is still issues with the new phase
settings. Enabling signal resampling seems to solve the problem
for these.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Align the default Core and Tx phase with the SoC vendor tree.
Even if the Tx phase is different from what the documentation
recommends, it seems to provide better results.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spinlock is only used within the irq handler so it does not
seem very useful.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On errors, if we don't stop the descriptor chain, it may continue to
run and raise IRQ after we have called mmc_request_done(). This is bad
because we won't be able to get cmd anymore and properly deal with the
IRQ.
This patch makes sure the descriptor chain is stopped before
calling mmc_request_done()
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trigger the reset line of the mmc controller while probing, if available.
The reset should be optional for now, at least until all related DT nodes
have the reset property.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Explicitly update the docomentation to support the Meson-AXG platform.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Introduce the compatible data to cover the register offset & mask
change of the eMMC controller in Amlogic's Meson-AXG SoC.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
This reverts commit 0a44697627.
This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.
We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue
Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.
According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.
Fixes: 0a44697627 ("mmc: meson-gx: include tx phase in the tuning process")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Meson GX MMC driver fails to build after commit 23c35f48f5
("pinctrl: remove include file from <linux/device.h>") because it relies
on the pinctrl/consumer.h being pulled in by the device.h header
implicitly.
Include the header explicitly to avoid the build failure.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been reported that some platforms (odroid-c2) may require
a different tx phase setting to operate at high speed (hs200 and hs400)
To improve the situation, this patch includes tx phase in the tuning
process.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resetting the phase when POWER_ON is set the set_ios() call means that the
phase is reset almost every time the set_ios() is called, while the
expected behavior was to reset the phase on a power cycle.
This had gone unnoticed until now because in all mode (except hs400) the
tuning is done after the last to set_ios(). In such case, the tuning
result is used anyway. In HS400, there are a few calls to set_ios() after
the tuning is done, overwriting the tuning result.
Resetting the phase on POWER_UP instead of POWER_ON solve the problem.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using CLK_DIVIDER_ROUND_CLOSEST is unsafe as the mmc clock could be
rounded to a rate higher the specified rate. Removing this flag ensure
that, if the rate needs to be rounded, it will be rounded down.
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using __bf_shf does not compile on arm 32 architecture.
This has gone unnoticed till now cause the driver is only used on arm64.
In addition, __bf_shf was already used in the driver without any issue.
It was used on a constant value, so the call was probably optimized
away.
Replace __bf_shf by __ffs fixes the problem
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rework tuning function of the rx phase. Now that the phase can be
more precisely set using CCF, test more phase setting and find the
largest working window. Then the tuning selected is the one at the
center of the window.
This rework allows to use new modes, such as UHS SDR50
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initial default tx phase was set to 0 while the datasheet recommends 270.
Some cards fails to initialize with this setting and eMMC mode DDR52 does
not work.
Changing this setting to 270 fixes these issues, without any regression
so far
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement voltage switch callback (shamelessly copied from sunxi mmc
driver). This allow, with the appropriate tuning function, to use
SD ultra high speed modes.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Several phases can be controlled on the meson-gx controller, the core, tx
and rx clock phase. The tx and rx uses delays to allow more fine grained
setting of the phase. To properly compute the phase using delays,
accessing the clock rate is necessary.
Instead of ad-hoc functions, use the common clock framework to set the
clock phases (and access the clock rate while doing it).
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the card_busy callback to be able to verify that the
card is done dealing with voltage switch, when the support is
added later on.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
