Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a queue is registered, the block layer turns off the bypass
setting (because bypass is enabled when the queue is created). This
doesn't work well for queues that are unregistered and then registered
again; we get a WARNING because of the unbalanced calls to
blk_queue_bypass_end().
This patch fixes the problem by making blk_register_queue() call
blk_queue_bypass_end() only the first time the queue is registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <tj@kernel.org>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
On systems with special thermal configurations make sure we make
note of the thermal setup. This is required for proper firmware
configuration on these systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There is no need to use hex_dump_to_buffer() since we have a kernel helper to
dump up to 64 bytes just via printk(). In our case the actual size is 15 bytes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PM entries of LPSS power domain were not implemented correctly
in commit c78b083066 "ACPI / LPSS: custom power domain for LPSS".
This patch fixes and completes these PM entries.
Fixes: c78b083066 (ACPI / LPSS: custom power domain for LPSS)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 232de51437 ("ACPI / battery: fix wrong value of
capacity_now reported when fully charged")
There is nothing wrong or unexpected about 'capacity_now' increasing above
the last 'full_charge_capacity' value. Different charging cycles will cause
'full_charge_capacity' to vary, both up and down. Good battery firmwares
will update 'full_charge_capacity' when the current charging cycle is
complete, increasing it if necessary. It might even go above
'design_capacity' on a fresh and healthy battery.
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong, and
printing a warning if this doesn't happen to match the 'design_capacity'
is both annoying and terribly wrong.
This results in bogus warnings on perfectly working systems/firmwares:
[Firmware Bug]: battery: reported current charge level (39800) is higher than reported maximum charge level (39800).
and wrong values being reported for 'capacity_now' and
'full_charge_capacity' after the warning has been triggered.
Fixes: 232de51437 ("ACPI / battery: fix wrong value of capacity_now reported when fully charged")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit d719870b41 ("ACPI / battery: Fix warning message in
acpi_battery_get_state()")
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong. If this
is necessary to work around some buggy firmware, then the workaround needs
protection against being applied to working firmwares.
Good battery firmwares will allow 'capacity_now' to increase above
'full_charge_capacity', and will update the latter when the battery
is fully charged. By capping 'capacity_now' we lose accurate capacity
reporting until charging is complete whenever 'full_charge_capacity'
needs to be increased.
Fixes: d719870b41 ("ACPI / battery: Fix warning message in acpi_battery_get_state()")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When DYNAMIC_DEBUG enabled, pr_debug() depends on KBUILD_MODNAME which
also depends on the modules number in Makefile. The related information
in "scripts/Makefile.lib" line 94:
# $(modname_flags) #defines KBUILD_MODNAME as the name of the module it will
# end up in (or would, if it gets compiled in)
# Note: Files that end up in two or more modules are compiled without the
# KBUILD_MODNAME definition. The reason is that any made-up name would
# differ in different configs.
For this case, 'radio-si470x-i2c.o' and 'radio-si470x-common.o' are in
one line, so cause compiling issue. And 'uaccess.h' is a common shared
header (not specially for drivers), so use pr_devel() instead of is OK.
The related error with allmodconfig:
CC [M] drivers/media/radio/si470x/radio-si470x-i2c.o
CC [M] drivers/media/radio/si470x/radio-si470x-common.o
In file included from include/linux/printk.h:257:0,
from include/linux/kernel.h:13,
from drivers/media/radio/si470x/radio-si470x.h:29,
from drivers/media/radio/si470x/radio-si470x-common.c:115:
./arch/microblaze/include/asm/uaccess.h: In function 'access_ok':
include/linux/dynamic_debug.h:66:14: error: 'KBUILD_MODNAME' undeclared (first use in this function)
.modname = KBUILD_MODNAME, \
^
include/linux/dynamic_debug.h:76:2: note: in expansion of macro 'DEFINE_DYNAMIC_DEBUG_METADATA'
DEFINE_DYNAMIC_DEBUG_METADATA(descriptor, fmt); \
^
include/linux/printk.h:263:2: note: in expansion of macro 'dynamic_pr_debug'
dynamic_pr_debug(fmt, ##__VA_ARGS__)
^
./arch/microblaze/include/asm/uaccess.h:101:3: note: in expansion of macro 'pr_debug'
pr_debug("ACCESS fail: %s at 0x%08x (size 0x%x), seg 0x%08x\n",
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
"entry.h" needs 'asmlinkage', and "asm/linkage.h" does not provide it.
So need include "linux/linkage.h" to use generic one instead of.
The related error (with allmodconfig under microblaze):
CC [M] drivers/net/ethernet/emulex/benet/be_main.o
In file included from ./arch/microblaze/include/asm/processor.h:17:0,
from include/linux/prefetch.h:14,
from drivers/net/ethernet/emulex/benet/be_main.c:18:
./arch/microblaze/include/asm/entry.h:33:19: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'void'
extern asmlinkage void do_notify_resume(struct pt_regs *regs, int in_syscall);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch wires up three new syscalls for powerpc. The three
new syscalls are seccomp, getrandom and memfd_create.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
CONFIG_FHANDLE is a requirement for systemd and with the increasing
uptake of systemd within distros it makes sense for 64 bit defconfigs
to include it.
Signed-off-by: Cyril Bur <cyril.bur@au1.ibm.com>
As opal_message_init() uses machine_early_initcall(powernv, ), and
opal_hmi_handler_init() depends on that early initcall, so it also needs
use machine_* to check the machine_id.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
ABIv2 kernels are failing to backtrace through the kernel. An example:
39.30% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
__GI___libc_read
The problem is in valid_next_sp() where we check that the new stack
pointer is at least STACK_FRAME_OVERHEAD below the previous one.
ABIv1 has a minimum stack frame size of 112 bytes consisting of 48 bytes
and 64 bytes of parameter save area. ABIv2 changes that to 32 bytes
with no paramter save area.
STACK_FRAME_OVERHEAD is in theory the minimum stack frame size,
but we over 240 uses of it, some of which assume that it includes
space for the parameter area.
We need to work through all our stack defines and rationalise them
but let's fix perf now by creating STACK_FRAME_MIN_SIZE and using
in valid_next_sp(). This fixes the issue:
30.64% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
pagecache_get_page
generic_file_read_iter
new_sync_read
vfs_read
sys_read
syscall_exit
__GI___libc_read
Cc: stable@vger.kernel.org # 3.16+
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Values acquired from Open Firmware are in 32-bit big endian format
and need to be handled on little endian architectures. This patch
ensures values are in cpu endian when hotplugging memory.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
The tx_empty() callback currently checks the TXEMPTY bit in the interrupt
status register to decided whether the FIFO should be reported as empty or
not. The bit in this register gets set when the FIFO state transitions from
non-empty to empty but is cleared again in the interrupt handler. This means
it is not suitable to be used to decided whether the FIFO is currently empty
or not. Instead use the TXEMPTY bit from the status register which will be
set as long as the FIFO is empty.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In set_termios(), interrupts where not disabled if UART_ENABLE_MS() was
false.
Tested on at91sam9g35.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # >= 3.16
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another new ACPI identifier for the 8250 dw bindings to cover newer Intel
SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the uwb_dev->bce entry is set before calling uwb_dev_add in
uwbd_dev_onair so that usermode will only see the device after it is
properly initialized. This fixes a kernel panic that can occur if
usermode tries to access the IEs sysfs attribute of a UWB device before
the driver has had a chance to set the beacon cache entry.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ext4 bugfix from Ted Ts'o.
[ Hmm. It's possible we should make kfree() aware of error pointers,
and use IS_ERR_OR_NULL rather than a NULL check. But in the meantime
this is obviously the right fix. - Linus ]
* 'for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid trying to kfree an ERR_PTR pointer
Pull nfsd bugfixes from Bruce Fields:
"A couple minor nfsd bugfixes"
* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
lockd: fix rpcbind crash on lockd startup failure
nfsd4: fix rd_dircount enforcement
Use the correct register address for Calibration Active and Interrupt
Enable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I've not done a full audit of all mouse drivers, I noticed these ones were
missing the POINTER property while working on the POINTING_STICK property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful for userspace to know that there not dealing with a regular
mouse but rather with a pointing stick (e.g. a trackpoint) so that
userspace can e.g. automatically enable middle button scrollwheel
emulation.
It is impossible to tell the difference from the evdev info without
resorting to putting a list of device / driver names in userspace, this is
undesirable.
Add a property which allows userspace to see if a device is a pointing
stick, and set it on all the pointing stick drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch corrects a lack of testing.
If fw is NULL when calling firmware_load(), it results in a kernel oops.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d24d481b7d (usb-storage: Modify and export adjust_quirks so
that it can be used by uas) added the 'u' flag to the quirks module
parameter for usb-storage, but neglected to update the
documentation. This patch adds the documentation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.
That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.
This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.
This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.
This patch should be backported to all kernels containing
commit 71c731a.
Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Btrfs was inserting inodes into the hash table before we had fully
set the inode up on disk. This leaves us open to rare races that allow
two different inodes in memory for the same [root, inode] pair.
This patch fixes things by using insert_inode_locked4 to insert an I_NEW
inode and unlock_new_inode when we're ready for the rest of the kernel
to use the inode.
It also makes sure to init the operations pointers on the inode before
going into the error handling paths.
Signed-off-by: Chris Mason <clm@fb.com>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
While we're doing a full fsync (when the inode has the flag
BTRFS_INODE_NEEDS_FULL_SYNC set) that is ranged too (covers only a
portion of the file), we might have ordered operations that are started
before or while we're logging the inode and that fall outside the fsync
range.
Therefore when a full ranged fsync finishes don't remove every extent
map from the list of modified extent maps - as for some of them, that
fall outside our fsync range, their respective ordered operation hasn't
finished yet, meaning the corresponding file extent item wasn't inserted
into the fs/subvol tree yet and therefore we didn't log it, and we must
let the next fast fsync (one that checks only the modified list) see this
extent map and log a matching file extent item to the log btree and wait
for its ordered operation to finish (if it's still ongoing).
A test case for xfstests follows.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
The "inherit" in btrfs_ioctl_snap_create_v2() and "vol_args" in
btrfs_ioctl_rm_dev() are ERR_PTRs so we can't call kfree() on them.
These kind of bugs are "One Err Bugs" where there is just one error
label that does everything. I could set the "inherit = NULL" and keep
the single out label but it ends up being more complicated that way. It
makes the code simpler to re-order the unwind so it's in the mirror
order of the allocation and introduce some new error labels.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
According to the documentation sync_fence_create takes ownership of the point,
not a reference on the point.
This fixes a memory leak introduced in 3.17's android fence rework.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Colin Cross <ccross@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to unbind imx-drm, the following oops was observed from
the imx-ldb driver:
Unable to handle kernel NULL pointer dereference at virtual address 0000001c
pgd = de954000
[0000001c] *pgd=2e92c831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in: bnep rfcomm bluetooth nfsd exportfs hid_cypress brcmfmac brcmutil snd_soc_fsl_ssi snd_soc_fsl_spdif imx_pcm_fiq imx_pcm_dma imx_ldb(C) imx_thermal imx_sdma imx2_wdt snd_soc_sgtl5000 snd_soc_imx_sgtl5000 snd_soc_imx_spdif snd_soc_imx_audmux
CPU: 1 PID: 1228 Comm: bash Tainted: G C 3.16.0-rc2+ #1229
task: ea378d80 ti: de948000 task.ti: de948000
PC is at imx_ldb_unbind+0x1c/0x58 [imx_ldb]
LR is at component_unbind+0x38/0x70
pc : [<bf025068>] lr : [<c0353108>] psr: 200f0013
sp : de949da8 ip : de949dc0 fp : de949dbc
r10: e9a44b0c r9 : 00000000 r8 : de949f78
r7 : 00000012 r6 : e9b3f400 r5 : e9b133b8 r4 : e9b13010
r3 : 00000000 r2 : e9b3f400 r1 : ea9a0210 r0 : e9b13020
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 2e95404a DAC: 00000015
Process bash (pid: 1228, stack limit = 0xde948240)
Stack: (0xde949da8 to 0xde94a000)
...
Backtrace:
[<bf02504c>] (imx_ldb_unbind [imx_ldb]) from [<c0353108>] (component_unbind+0x38/0x70)
[<c03530d0>] (component_unbind) from [<c03531d4>] (component_unbind_all+0x94/0xc8)
[<c0353140>] (component_unbind_all) from [<c04bc224>] (imx_drm_driver_unload+0x34/0x4c)
[<c04bc1f0>] (imx_drm_driver_unload) from [<c03394a4>] (drm_dev_unregister+0x2c/0xa0)
[<c0339478>] (drm_dev_unregister) from [<c0339f8c>] (drm_put_dev+0x30/0x6c)
[<c0339f5c>] (drm_put_dev) from [<c04bc1cc>] (imx_drm_unbind+0x14/0x18)
[<c04bc1b8>] (imx_drm_unbind) from [<c03530b4>] (component_master_del+0xbc/0xd8)
...
Code: e5904058 e2840010 e2845fea e59430a0 (e593301c)
---[ end trace 4f211c6dbbcd4963 ]---
This is caused by only having one channel out of the pair configured in
DT; the second channel remains uninitialised, but upon unbind, the
driver attempts to clean up both, thereby dereferencing a NULL pointer.
Avoid this by checking that the second channel is initialised.
Fixes: 1b3f767566 ("imx-drm: initialise drm components directly")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Semaphore values have 64 bits, not 32. This fixes a very subtle bug
that disables synchronization when the upper 32bits wasn't zero.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Reviewed-By: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 3b29970909 "nfsd4: enforce rd_dircount" totally misunderstood
rd_dircount; it refers to total non-attribute bytes returned, not number
of directory entries returned.
Bring the code into agreement with RFC 3530 section 14.2.24.
Cc: stable@vger.kernel.org
Fixes: 3b29970909 "nfsd4: enforce rd_dircount"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Pull s390 fixes from Martin Schwidefsky:
"A bug fix for the vdso code, the loadparm for booting from SCSI is
added and the access permissions for the dasd module parameters are
corrected"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vdso: remove NULL pointer check from clock_gettime
s390/ipl: Add missing SCSI loadparm attributes to /sys/firmware
s390/dasd: Make module parameter visible in sysfs
