[ Upstream commit 73964c1d07 ]
It is possible that the host connected and saw a cm established
event and started sending nvme capsules on the qp, however the
ctrl did not yet see an established event. This is why the
rsp_wait_list exists (for async handling of these cmds, we move
them to a pending list).
Furthermore, it is possible that the ctrl cm times out, resulting
in a connect-error cm event. in this case we hit a bad deref [1]
because in nvmet_rdma_free_rsps we assume that all the responses
are in the free list.
We are freeing the cmds array anyways, so don't even bother to
remove the rsp from the free_list. It is also guaranteed that we
are not racing anything when we are releasing the queue so no
other context accessing this array should be running.
[1]:
--
Workqueue: nvmet-free-wq nvmet_rdma_free_queue_work [nvmet_rdma]
[...]
pc : nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
lr : nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
Call trace:
nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
process_one_work+0x1ec/0x4a0
worker_thread+0x48/0x490
kthread+0x158/0x160
ret_from_fork+0x10/0x18
--
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0889d13b9e ]
When the length check for an icreq sqe fails we should not
continue processing but rather return immediately as all
other contents of that sqe cannot be relied on.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e80eb792b ]
The memory allocated for the identification is freed on failure. Set
it to NULL so the caller doesn't have a pointer to that freed address.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e716cec6f ]
The first command issued from the host to the target is the fabrics
connect command. At this point, neither the target queue nor the
controller have been allocated. But we already try to trace this command
in nvmet_req_init.
Reported by KASAN.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ab091ec536 upstream.
There is a hardware power-saving problem with the Lenovo N60z
board. When turn it on and leave it for 10 hours, there is a
20% chance that a nvme disk will not wake up until reboot.
Link: https://lore.kernel.org/all/2B5581C46AC6E335+9c7a81f1-05fb-4fd0-9fbb-108757c21628@uniontech.com
Signed-off-by: hmy <huanglin@uniontech.com>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf546dd289 ]
If we allocate a bio that is larger than NVMe maximum request size,
attach integrity metadata to it and send it to the NVMe subsystem, the
integrity metadata will be corrupted.
Splitting the bio works correctly. The function bio_split will clone the
bio, trim the iterator of the first bio and advance the iterator of the
second bio.
However, the function rq_integrity_vec has a bug - it returns the first
vector of the bio's metadata and completely disregards the metadata
iterator that was advanced when the bio was split. Thus, the second bio
uses the same metadata as the first bio and this leads to metadata
corruption.
This commit changes rq_integrity_vec, so that it calls mp_bvec_iter_bvec
instead of returning the first vector. mp_bvec_iter_bvec reads the
iterator and uses it to build a bvec for the current position in the
iterator.
The "queue_max_integrity_segments(rq->q) > 1" check was removed, because
the updated rq_integrity_vec function works correctly with multiple
segments.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/49d1afaa-f934-6ed2-a678-e0d428c63a65@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c31fad1470 ]
nvme_map_data() is called when request has physical segments, hence
the nvme_unmap_data() should have same condition to avoid dereference.
Fixes: 4aedb70543 ("nvme-pci: split metadata handling from nvme_map_data / nvme_unmap_data")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92fc2c469e ]
pcie_aspm=off tells the kernel not to modify the ASPM configuration. This
setting does not guarantee that ASPM (Active State Power Management) is
disabled. Hence add pcie_port_pm=off. This disables power management for
all PCIe ports.
This patch has been tested on a workstation with a Samsung SSD 970 EVO Plus
NVMe SSD.
Fixes: 4641a8e6e1 ("nvme-pci: add trouble shooting steps for timeouts")
Cc: Keith Busch <kbusch@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f58f96d1 ]
If we fail to call nvme_auth_augmented_challenge, or fail to kmalloc
for shash, we should free the memory allocation for challenge, so add
err path out_free_challenge to fix the memory leak.
Fixes: 7a277c37d3 ("nvmet-auth: Diffie-Hellman key exchange support")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9570a48847 ]
The value of NVME_NS_DEAC is 3,
which means NVME_NS_METADATA_SUPPORTED | NVME_NS_EXT_LBAS. Provide a
unique value for this feature flag.
Fixes 1b96f862ec ("nvme: implement the DEAC bit for the Write Zeroes command")
Signed-off-by: Boyang Yu <yuboyang@dapustor.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd0c1b8e04 ]
The spec doesn't mandate that the first two double words (aka results)
for the command queue entry need to be set to 0 when they are not
used (not specified). Though, the target implemention returns 0 for TCP
and FC but not for RDMA.
Let's make RDMA behave the same and thus explicitly initializing the
result field. This prevents leaking any data from the stack.
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d574ab37 ]
If a discard request needs to be retried, and that retry may fail before
a new special payload is added, a double free will result. Clear the
RQF_SPECIAL_LOAD when the request is cleaned.
Signed-off-by: Chunguang Xu <chunguang.xu@shopee.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c758b77d4a ]
In nvmet_sq_destroy we capture sq->ctrl early and if it is non-NULL we
know that a ctrl was allocated (in the admin connect request handler)
and we need to release pending AERs, clear ctrl->sqs and sq->ctrl
(for nvme-loop primarily), and drop the final reference on the ctrl.
However, a small window is possible where nvmet_sq_destroy starts (as
a result of the client giving up and disconnecting) concurrently with
the nvme admin connect cmd (which may be in an early stage). But *before*
kill_and_confirm of sq->ref (i.e. the admin connect managed to get an sq
live reference). In this case, sq->ctrl was allocated however after it was
captured in a local variable in nvmet_sq_destroy.
This prevented the final reference drop on the ctrl.
Solve this by re-capturing the sq->ctrl after all inflight request has
completed, where for sure sq->ctrl reference is final, and move forward
based on that.
This issue was observed in an environment with many hosts connecting
multiple ctrls simoutanuosly, creating a delay in allocating a ctrl
leading up to this race window.
Reported-by: Alex Turin <alex@vastdata.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bd293fcf3 ]
bio_vec start offset may be relatively large particularly when large
folio gets added to the bio. A bigger offset will result in avoiding the
single-segment mapping optimization and end up using expensive
mempool_alloc further.
Rather than using absolute value, adjust bv_offset by
NVME_CTRL_PAGE_SIZE while checking if segment can be fitted into one/two
PRP entries.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kundan Kumar <kundan.kumar@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3a043733f ]
In current native multipath design when a shared namespace is created,
we loop through each possible numa-node, calculate the NUMA distance of
that node from each nvme controller and then cache the optimal IO path
for future reference while sending IO. The issue with this design is that
we may refer to the NUMA distance table for an offline node which may not
be populated at the time and so we may inadvertently end up finding and
caching a non-optimal path for IO. Then latter when the corresponding
numa-node becomes online and hence the NUMA distance table entry for that
node is created, ideally we should re-calculate the multipath node distance
for the newly added node however that doesn't happen unless we rescan/reset
the controller. So essentially, we may keep using non-optimal IO path for a
node which is made online after namespace is created.
This patch helps fix this issue ensuring that when a shared namespace is
created, we calculate the multipath node distance for each online numa-node
instead of each possible numa-node. Then latter when a node becomes online
and we receive any IO on that newly added node, we would calculate the
multipath node distance for newly added node but this time NUMA distance
table would have been already populated for newly added node. Hence we
would be able to correctly calculate the multipath node distance and choose
the optimal path for the IO.
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d76584e53f ]
The id override functions return a status which is not propagated to the
caller.
Fixes: c1fef73f79 ("nvmet: add passthru code to process commands")
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a1fdd709 ]
Fix the parsing if extra status bits (e.g. MORE) is present.
Fixes: 7fb42780d0 ("nvme: Convert NVMe errors to PR errors")
Signed-off-by: Weiwen Hu <huweiwen@linux.alibaba.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f97914e35f ]
When disabling an nvmet namespace, there is a period where the
subsys->lock is released, as the ns disable waits for backend IO to
complete, and the ns percpu ref to be properly killed. The original
intent was to avoid taking the subsystem lock for a prolong period as
other processes may need to acquire it (for example new incoming
connections).
However, it opens up a window where another process may come in and
enable the ns, (re)intiailizing the ns percpu_ref, causing the disable
sequence to hang.
Solve this by taking the global nvmet_config_sem over the entire configfs
enable/disable sequence.
Fixes: a07b4970f4 ("nvmet: add a generic NVMe target")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2e4c5f5f6 ]
There are io stats accounting that needs to be handled, so don't call
blk_mq_end_request() directly. Use the existing nvme_end_req() helper
that already handles everything.
Fixes: d4d957b53d ("nvme-multipath: support io stats on the mpath device")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d15dcd0f1a ]
The nsid value is a u32 that comes from nvmet_req_find_ns(). It's
endian data and we're on an error path and both of those raise red
flags. So let's make this safer.
1) Make the buffer large enough for any u32.
2) Remove the unnecessary initialization.
3) Use snprintf() instead of sprintf() for even more safety.
4) The sprintf() function returns the number of bytes printed, not
counting the NUL terminator. It is impossible for the return value to
be <= 0 so delete that.
Fixes: 505363957f ("nvmet: fix nvme status code when namespace is disabled")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 505363957f ]
If the user disabled a nvmet namespace, it is removed from the subsystem
namespaces list. When nvmet processes a command directed to an nsid that
was disabled, it cannot differentiate between a nsid that is disabled
vs. a non-existent namespace, and resorts to return NVME_SC_INVALID_NS
with the dnr bit set.
This translates to a non-retryable status for the host, which translates
to a user error. We should expect disabled namespaces to not cause an
I/O error in a multipath environment.
Address this by searching a configfs item for the namespace nvmet failed
to find, and if we found one, conclude that the namespace is disabled
(perhaps temporarily). Return NVME_SC_INTERNAL_PATH_ERROR in this case
and keep DNR bit cleared.
Reported-by: Jirong Feng <jirong.feng@easystack.cn>
Tested-by: Jirong Feng <jirong.feng@easystack.cn>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6825bdde44 ]
When we teardown the controller, we wait for pending I/Os to complete
(sq->ref on all queues to drop to zero) and then we go over the commands,
and free their command buffers in case they are still fetching data from
the host (e.g. processing nvme writes) and have yet to take a reference
on the sq.
However, we may miss the case where commands have failed before executing
and are queued for sending a response, but will never occur because the
queue socket is already down. In this case we may miss deallocating command
buffers.
Solve this by freeing all commands buffers as nvmet_tcp_free_cmd_buffers is
idempotent anyways.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25bb3534ee ]
While I/O is running, if the pci bus error occurs then
in-flight I/O can not complete. Worst, if at this time,
user (logically) hot-unplug the nvme disk then the
nvme_remove() code path can't forward progress until
in-flight I/O is cancelled. So these sequence of events
may potentially hang hot-unplug code path indefinitely.
This patch helps cancel the pending/in-flight I/O from the
nvme request timeout handler in case the nvme controller
is in the terminal (DEAD/DELETING/DELETING_NOIO) state and
that helps nvme_remove() code path forward progress and
finish successfully.
Link: https://lore.kernel.org/all/199be893-5dfa-41e5-b6f2-40ac90ebccc4@linux.ibm.com/
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 445f9119e7 ]
In nvmet_auth_host_hash(), if a mismatch is detected in the hash length
the kernel should print an error.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46b8f9f74f ]
If the nvmet_auth_host_hash() function fails, the error code should
be returned to its callers.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 863fe60ed2 ]
On system where native nvme multipath is configured and iopolicy
is set to numa but the nvme controller numa node id is undefined
or -1 (NUMA_NO_NODE) then avoid calculating node distance for
finding optimal io path. In such case we may access numa distance
table with invalid index and that may potentially refer to incorrect
memory. So this patch ensures that if the nvme controller numa node
id is -1 then instead of calculating node distance for finding optimal
io path, we set the numa node distance of such controller to default 10
(LOCAL_DISTANCE).
Link: https://lore.kernel.org/all/20240413090614.678353-1-nilay@linux.ibm.com/
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d5887dc6b6 upstream.
Sandisk SN530 NVMe drives have broken MSIs. On systems without MSI-X
support, all commands time out resulting in the following message:
nvme nvme0: I/O tag 12 (100c) QID 0 timeout, completion polled
These timeouts cause the boot to take an excessively-long time (over 20
minutes) while the initial command queue is flushed.
Address this by adding a quirk for drives with buggy MSIs. The lspci
output for this device (recorded on a system with MSI-X support) is:
02:00.0 Non-Volatile memory controller: Sandisk Corp Device 5008 (rev 01) (prog-if 02 [NVM Express])
Subsystem: Sandisk Corp Device 5008
Flags: bus master, fast devsel, latency 0, IRQ 16, NUMA node 0
Memory at f7e00000 (64-bit, non-prefetchable) [size=16K]
Memory at f7e04000 (64-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 3
Capabilities: [90] MSI: Enable- Count=1/32 Maskable- 64bit+
Capabilities: [b0] MSI-X: Enable+ Count=17 Masked-
Capabilities: [c0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [1b8] Latency Tolerance Reporting
Capabilities: [300] Secondary PCI Express
Capabilities: [900] L1 PM Substates
Kernel driver in use: nvme
Kernel modules: nvme
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0bc2e80b9b ]
Move the stray '.' that is currently at the end of the line after
newline '\n' to before newline character which is the right position.
Fixes: ce8d78616a ("nvme: warn about shared namespaces without CONFIG_NVME_MULTIPATH")
Signed-off-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89086c43f ]
This commit adds NVME_QUIRK_NO_DEEPEST_PS and NVME_QUIRK_BOGUS_NID for
device [126f:2262], which appears to be a generic VID:PID pair used for
many SSDs based on the Silicon Motion SM2262/SM2262EN controller.
Two of my SSDs with this VID:PID pair exhibit the same behavior:
* They frequently have trouble exiting the deepest power state (5),
resulting in the entire disk unresponsive.
Verified by setting nvme_core.default_ps_max_latency_us=10000 and
observing them behaving normally.
* They produce all-zero nguid and eui64 with `nvme id-ns` command.
The offending products are:
* HP SSD EX950 1TB
* HIKVISION C2000Pro 2TB
Signed-off-by: Jiawei Fu <i@ibugone.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de105068fe ]
We found a issue on production environment while using NVMe over RDMA,
admin_q reconnect failed forever while remote target and network is ok.
After dig into it, we found it may caused by a ABBA deadlock due to tag
allocation. In my case, the tag was hold by a keep alive request
waiting inside admin_q, as we quiesced admin_q while reset ctrl, so the
request maked as idle and will not process before reset success. As
fabric_q shares tagset with admin_q, while reconnect remote target, we
need a tag for connect command, but the only one reserved tag was held
by keep alive command which waiting inside admin_q. As a result, we
failed to reconnect admin_q forever. In order to fix this issue, I
think we should keep two reserved tags for admin queue.
Fixes: ed01fee283 ("nvme-fabrics: only reserve a single tag")
Signed-off-by: Chunguang Xu <chunguang.xu@shopee.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe506a7458 ]
We have to ensure that the tgtport is not going away
before be have remove all the associations.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 710c69dbac ]
When deleting an association the shutdown path is deadlocking because we
try to flush the nvmet_wq nested. Avoid this by deadlock by deferring
the put work into its own work item.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3146345c2e ]
When the target port has not active port binding, there is no point in
trying to process the command as it has to fail anyway. Instead adding
checks to all commands abort the command early.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca121a0f75 ]
The hostport data structure is shared between the association, this why
we keep track of the users via a refcount. So we should not decrement
the refcount on a match and free the hostport several times.
Reported by KASAN.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4049dc96b8 ]
When the target executes a disconnect and the host triggers a reconnect
immediately, the reconnect command still finds an existing association.
The reconnect crashes later on because nvmet_fc_delete_target_assoc
blindly removes resources while the reconnect code wants to use it.
To address this, nvmet_fc_find_target_assoc should not be able to
lookup an association which is being removed. The association list
is already under RCU lifetime management, so let's properly use it
and remove the association from the list and wait for a grace period
before cleaning up all. This means we also can drop the RCU management
on the queues, because this is now handled via the association itself.
A second step split the execution context so that the initial disconnect
command can complete without running the reconnect code in the same
context. As usual, this is done by deferring the ->done to a workqueue.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c691e6d7e1 ]
In case we return early out of __nvmet_fc_finish_ls_req() we still have
to release the reference on the target port.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcfad4ab4d ]
The first argument of list_add_tail function is the new element which
should be added to the list which is the second argument. Swap the
arguments to allow processing more than one element at a time.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70fbfc47a3 ]
The module exit path has race between deleting all controllers and
freeing 'left over IDs'. To prevent double free a synchronization
between nvme_delete_ctrl and ida_destroy has been added by the initial
commit.
There is some logic around trying to prevent from hanging forever in
wait_for_completion, though it does not handling all cases. E.g.
blktests is able to reproduce the situation where the module unload
hangs forever.
If we completely rely on the cleanup code executed from the
nvme_delete_ctrl path, all IDs will be freed eventually. This makes
calling ida_destroy unnecessary. We only have to ensure that all
nvme_delete_ctrl code has been executed before we leave
nvme_fc_exit_module. This is done by flushing the nvme_delete_wq
workqueue.
While at it, remove the unused nvme_fc_wq workqueue too.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c5dd66c1 ]
The nvmet_tcp_queue_ida should be destroy when the nvmet-tcp module
exit.
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a1abc2485 ]
The nvmet_tcp_handle_h2c_data_pdu() function should take into
consideration the possibility that the header digest and/or the data
digests are enabled when calculating the expected PDU length, before
comparing it to the value stored in cmd->pdu_len.
Fixes: efa5630590 ("nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7de1dea76 ]
A previous patch introduced a struct_group() in nvme_common_command to help
stringop fortification figure out the length of the fields, but one function
is not currently using them:
In file included from drivers/nvme/target/core.c:7:
In file included from include/linux/string.h:254:
include/linux/fortify-string.h:592:4: error: call to '__read_overflow2_field' declared with 'warning' attribute: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
^
Change this one to use the correct field name to avoid the warning.
Fixes: 5c629dc960 ("nvme: use struct group for generic command dwords")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ee7ffeb4c ]
An earlier patch had tried to address a warning about a string copy with
missing zero termination:
drivers/nvme/target/trace.h:52:3: warning: ‘strncpy’ specified bound 32 equals destination size [-Wstringop-truncation]
The new version causes a different warning with some compiler versions, notably
gcc-9 and gcc-10, and also misses the zero padding that was apparently done
intentionally in the original code:
drivers/nvme/target/trace.h:56:2: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
Change it to use strscpy_pad() with the original length, which will give
a properly padded and zero-terminated string as well as avoiding the warning.
Fixes: d86481e924 ("nvmet: use min of device_path and disk len")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0849a54413 ]
in nvmet_tcp_handle_h2c_data_pdu(), if the host sends a data_offset
different from rbytes_done, the driver ends up calling nvmet_req_complete()
passing a status error.
The problem is that at this point cmd->req is not yet initialized,
the kernel will crash after dereferencing a NULL pointer.
Fix the bug by replacing the call to nvmet_req_complete() with
nvmet_tcp_fatal_error().
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Reviewed-by: Keith Busch <kbsuch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa5630590 ]
If the host sends an H2CData command with an invalid DATAL,
the kernel may crash in nvmet_tcp_build_pdu_iovec().
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp]
Call trace:
process_one_work+0x174/0x3c8
worker_thread+0x2d0/0x3e8
kthread+0x104/0x110
Fix the bug by raising a fatal error if DATAL isn't coherent
with the packet size.
Also, the PDU length should never exceed the MAXH2CDATA parameter which
has been communicated to the host in nvmet_tcp_handle_icreq().
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 839a40d1e7 ]
If controller reset occurs when allocating namespace, both
nvme_reset_work and nvme_scan_work will hang, as shown below.
Test Scripts:
for ((t=1;t<=128;t++))
do
nsid=`nvme create-ns /dev/nvme1 -s 14537724 -c 14537724 -f 0 -m 0 \
-d 0 | awk -F: '{print($NF);}'`
nvme attach-ns /dev/nvme1 -n $nsid -c 0
done
nvme reset /dev/nvme1
We will find that both nvme_reset_work and nvme_scan_work hung:
INFO: task kworker/u249:4:17848 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
task:kworker/u249:4 state:D stack: 0 pid:17848 ppid: 2
flags:0x00000028
Workqueue: nvme-reset-wq nvme_reset_work [nvme]
Call trace:
__switch_to+0xb4/0xfc
__schedule+0x22c/0x670
schedule+0x4c/0xd0
blk_mq_freeze_queue_wait+0x84/0xc0
nvme_wait_freeze+0x40/0x64 [nvme_core]
nvme_reset_work+0x1c0/0x5cc [nvme]
process_one_work+0x1d8/0x4b0
worker_thread+0x230/0x440
kthread+0x114/0x120
INFO: task kworker/u249:3:22404 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
task:kworker/u249:3 state:D stack: 0 pid:22404 ppid: 2
flags:0x00000028
Workqueue: nvme-wq nvme_scan_work [nvme_core]
Call trace:
__switch_to+0xb4/0xfc
__schedule+0x22c/0x670
schedule+0x4c/0xd0
rwsem_down_write_slowpath+0x32c/0x98c
down_write+0x70/0x80
nvme_alloc_ns+0x1ac/0x38c [nvme_core]
nvme_validate_or_alloc_ns+0xbc/0x150 [nvme_core]
nvme_scan_ns_list+0xe8/0x2e4 [nvme_core]
nvme_scan_work+0x60/0x500 [nvme_core]
process_one_work+0x1d8/0x4b0
worker_thread+0x260/0x440
kthread+0x114/0x120
INFO: task nvme:28428 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
task:nvme state:D stack: 0 pid:28428 ppid: 27119
flags:0x00000000
Call trace:
__switch_to+0xb4/0xfc
__schedule+0x22c/0x670
schedule+0x4c/0xd0
schedule_timeout+0x160/0x194
do_wait_for_common+0xac/0x1d0
__wait_for_common+0x78/0x100
wait_for_completion+0x24/0x30
__flush_work.isra.0+0x74/0x90
flush_work+0x14/0x20
nvme_reset_ctrl_sync+0x50/0x74 [nvme_core]
nvme_dev_ioctl+0x1b0/0x250 [nvme_core]
__arm64_sys_ioctl+0xa8/0xf0
el0_svc_common+0x88/0x234
do_el0_svc+0x7c/0x90
el0_svc+0x1c/0x30
el0_sync_handler+0xa8/0xb0
el0_sync+0x148/0x180
The reason for the hang is that nvme_reset_work occurs while nvme_scan_work
is still running. nvme_scan_work may add new ns into ctrl->namespaces
list after nvme_reset_work frozen all ns->q in ctrl->namespaces list.
The newly added ns is not frozen, so nvme_wait_freeze will wait forever.
Unfortunately, ctrl->namespaces_rwsem is held by nvme_reset_work, so
nvme_scan_work will also wait forever. Now we are deadlocked!
PROCESS1 PROCESS2
============== ==============
nvme_scan_work
... nvme_reset_work
nvme_validate_or_alloc_ns nvme_dev_disable
nvme_alloc_ns nvme_start_freeze
down_write ...
nvme_ns_add_to_ctrl_list ...
up_write nvme_wait_freeze
... down_read
nvme_alloc_ns blk_mq_freeze_queue_wait
down_write
Fix by marking the ctrl with say NVME_CTRL_FROZEN flag set in
nvme_start_freeze and cleared in nvme_unfreeze. Then the scan can check
it before adding the new namespace (under the namespaces_rwsem).
Signed-off-by: Bitao Hu <yaoma@linux.alibaba.com>
Reviewed-by: Guixin Liu <kanie@linux.alibaba.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20dc66f2d7 ]
This patch fixes the smatch warning, "nvmet_ns_ana_grpid_store() warn:
potential spectre issue 'nvmet_ana_group_enabled' [w] (local cap)"
Prevent the contents of kernel memory from being leaked to user space
via speculative execution by using array_index_nospec.
Signed-off-by: Nitesh Shetty <nj.shetty@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7be866b1cf ]
This can be an expensive call on some kernel configs. Move it to the end
after checking the cheaper ways to determine if the command is allowed.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6e7f7ac03 ]
A different CPU may be setting the ctrl->state value, so ensure proper
barriers to prevent optimizing to a stale state. Normally it isn't a
problem to observe the wrong state as it is merely advisory to take a
quicker path during initialization and error recovery, but seeing an old
state can report unexpected ENETRESET errors when a reset request was in
fact successful.
Reported-by: Minh Hoang <mh2022@meta.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c687c287c ]
The controller state is typically written by another CPU, so reading it
should ensure no optimizations are taken. This is a repeated pattern in
the driver, so start with adding a convenience function that returns the
controller state with READ_ONCE().
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74fbc88e16 ]
The block layer doesn't support logical block sizes smaller than 512
bytes. The nvme spec doesn't support that small either, but the driver
isn't checking to make sure the device responded with usable data.
Failing to catch this will result in a kernel bug, either from a
division by zero when stacking, or a zero length bio.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
