The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-4-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-3-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-2-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The hwrng_fill() function can run while devices are suspending and
resuming. If the hwrng is behind a bus such as i2c or SPI and that bus
is suspended, the hwrng may hang the bus while attempting to add some
randomness. It's been observed on ChromeOS devices with suspend-to-idle
(s2idle) and an i2c based hwrng that this kthread may run and ask the
hwrng device for randomness before the i2c bus has been resumed.
Let's make this kthread freezable so that we don't try to touch the
hwrng during suspend/resume. This ensures that we can't cause the hwrng
backing driver to get into a bad state because the device is guaranteed
to be resumed before the hwrng kthread is thawed.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ipmi_thread() uses back-to-back schedule() to poll for command
completion which, on some machines, can push up CPU consumption and
heavily tax the scheduler locks leading to noticeable overall
performance degradation.
This was originally added so firmware updates through IPMI would
complete in a timely manner. But we can't kill the scheduler
locks for that one use case.
Instead, only run schedule() continuously in maintenance mode,
where firmware updates should run.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The nr_allocated_banks and allocated banks are initialized as part of
tpm_chip_register. Currently, this is done as part of auto startup
function. However, some drivers, like the ibm vtpm driver, do not run
auto startup during initialization. This results in uninitialized memory
issue and causes a kernel panic during boot.
This patch moves the pcr allocation outside the auto startup function
into tpm_chip_register. This ensures that allocated banks are initialized
in any case.
Fixes: 879b589210 ("tpm: retrieve digest size of unknown algorithms with PCR read")
Reported-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
ipmi_si_sm.h was getting included in lots of places it didn't
belong. Rework things a bit to remove all the dependencies,
mostly just moving things between include files that were in
the wrong place and removing bogus includes.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Use devm_hwrng_register to simplify the implementation.
Manual unregistration and some remove functions can be
removed now.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no need for timespec64, and it will cause issues in the
future with i386 and 64-bit division not being available.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Nothing else has come in besides things that need to wait until later.
-----BEGIN PGP SIGNATURE-----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=kk5y
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.3-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fix from Corey Minyard:
"One necessary fix for an uninitialized variable in the new IPMB driver.
Nothing else has come in besides things that need to wait until later"
* tag 'for-linus-5.3-2' of git://github.com/cminyard/linux-ipmi:
Fix uninitialized variable in ipmb_dev_int.c
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In pp_release(), there is an if statement on line 730 to check whether
pp->pdev is NULL:
else if ((pp->flags & PP_CLAIMED) && pp->pdev && ...)
When pp->pdev is NULL, it is used on line 743:
info = &pp->pdev->port->ieee1284;
and on line 748:
parport_release(pp->pdev);
Thus, a possible null-pointer dereference may occur.
To fix this bug, pp->pdev is checked on line 740.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20190724090426.1401-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ret at line 112 of ipmb_dev_int.c is uninitialized which
results in a warning during build regressions.
This warning was found by build regression/improvement
testing for v5.3-rc1.
Reported-by: build regression/improvement testing for v5.3-rc1.
Fixes: 51bd6f2915 ("Add support for IPMB driver")
Signed-off-by: Asmaa Mnebhi <Asmaa@mellanox.com>
Message-Id: <571dbb67cf58411d567953d9fb3739eb4789238b.1563996586.git.Asmaa@mellanox.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There are lots of documents that belong to the admin-guide but
are on random places (most under Documentation root dir).
Move them to the admin guide.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The docs under Documentation/laptops contain users specific
information.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Rename the laptops documentation files to ReST, add an
index for them and adjust in order to produce a nice html
output via the Sphinx build system.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
by automated tools.
Plus add a driver that allows Linux to act as an IPMB slave device,
so it can be a satellite MC in an IPMI network.
-----BEGIN PGP SIGNATURE-----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=SCDk
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.3' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Some small fixes for various things, nothing huge, mostly found by
automated tools.
Plus add a driver that allows Linux to act as an IPMB slave device, so
it can be a satellite MC in an IPMI network"
* tag 'for-linus-5.3' of git://github.com/cminyard/linux-ipmi:
docs: ipmb: place it at driver-api and convert to ReST
fix platform_no_drv_owner.cocci warnings
ipmi: ipmb: don't allocate i2c_client on stack
ipmi: ipmb: Fix build error while CONFIG_I2C is set to m
Add support for IPMB driver
drivers: ipmi: Drop device reference
ipmi_ssif: fix unexpected driver unregister warning
ipmi_si: use bool type for initialized variable
ipmi_si: fix unexpected driver unregister warning
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Here is the "large" pull request for char and misc and other assorted
smaller driver subsystems for 5.3-rc1.
It seems that this tree is becoming the funnel point of lots of smaller
driver subsystems, which is fine for me, but that's why it is getting
larger over time and does not just contain stuff under drivers/char/ and
drivers/misc.
Lots of small updates all over the place here from different driver
subsystems:
- habana driver updates
- coresight driver updates
- documentation file movements and updates
- Android binder fixes and updates
- extcon driver updates
- google firmware driver updates
- fsi driver updates
- smaller misc and char driver updates
- soundwire driver updates
- nvmem driver updates
- w1 driver fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXmoQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylV9wCgyJGbpPch8v/ecrZGFHYS4sIMexIAoMco3zf6
wnqFmXiz1O0tyo1sgV9R
=7sqO
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the "large" pull request for char and misc and other assorted
smaller driver subsystems for 5.3-rc1.
It seems that this tree is becoming the funnel point of lots of
smaller driver subsystems, which is fine for me, but that's why it is
getting larger over time and does not just contain stuff under
drivers/char/ and drivers/misc.
Lots of small updates all over the place here from different driver
subsystems:
- habana driver updates
- coresight driver updates
- documentation file movements and updates
- Android binder fixes and updates
- extcon driver updates
- google firmware driver updates
- fsi driver updates
- smaller misc and char driver updates
- soundwire driver updates
- nvmem driver updates
- w1 driver fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (188 commits)
coresight: Do not default to CPU0 for missing CPU phandle
dt-bindings: coresight: Change CPU phandle to required property
ocxl: Allow contexts to be attached with a NULL mm
fsi: sbefifo: Don't fail operations when in SBE IPL state
coresight: tmc: Smatch: Fix potential NULL pointer dereference
coresight: etm3x: Smatch: Fix potential NULL pointer dereference
coresight: Potential uninitialized variable in probe()
coresight: etb10: Do not call smp_processor_id from preemptible
coresight: tmc-etf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: alloc_perf_buf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: Do not call smp_processor_id() from preemptible
docs: misc-devices: convert files without extension to ReST
fpga: dfl: fme: align PR buffer size per PR datawidth
fpga: dfl: fme: remove copy_to_user() in ioctl for PR
fpga: dfl-fme-mgr: fix FME_PR_INTFC_ID register address.
intel_th: msu: Start read iterator from a non-empty window
intel_th: msu: Split sgt array and pointer in multiwindow mode
intel_th: msu: Support multipage blocks
intel_th: pci: Add Ice Lake NNPI support
intel_th: msu: Fix single mode with disabled IOMMU
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
-----BEGIN PGP SIGNATURE-----
iJYEABYIAD4WIQRE6pSOnaBC00OEHEIaerohdGur0gUCXRGG5iAcamFya2tvLnNh
a2tpbmVuQGxpbnV4LmludGVsLmNvbQAKCRAaerohdGur0lcRAP9xHUuaHm7/d6Qh
nAa1Sm+99aO1D/9WfEc4pjy3hASyOAEAwIecBZ5t8JceXXaYEv/rYNJCpogvZyyf
mdU4p9sc8AU=
=lzfE
-----END PGP SIGNATURE-----
Merge tag 'tpmdd-next-20190625' of git://git.infradead.org/users/jjs/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"This contains two critical bug fixes and support for obtaining TPM
events triggered by ExitBootServices().
For the latter I have to give a quite verbose explanation not least
because I had to revisit all the details myself to remember what was
going on in Matthew's patches.
The preboot software stack maintains an event log that gets entries
every time something gets hashed to any of the PCR registers. What
gets hashed could be a component to be run or perhaps log of some
actions taken just to give couple of coarse examples. In general,
anything relevant for the boot process that the preboot software does
gets hashed and a log entry with a specific event type [1].
The main application for this is remote attestation and the reason why
it is useful is nicely put in the very first section of [1]:
"Attestation is used to provide information about the platform’s
state to a challenger. However, PCR contents are difficult to
interpret; therefore, attestation is typically more useful when
the PCR contents are accompanied by a measurement log. While not
trusted on their own, the measurement log contains a richer set of
information than do the PCR contents. The PCR contents are used to
provide the validation of the measurement log."
Because EFI_TCG2_PROTOCOL.GetEventLog() is not available after calling
ExitBootServices(), Linux EFI stub copies the event log to a custom
configuration table. Unfortunately, ExitBootServices() also generates
events and obviously these events do not get copied to that table.
Luckily firmware does this for us by providing a configuration table
identified by EFI_TCG2_FINAL_EVENTS_TABLE_GUID.
This essentially contains necessary changes to provide the full event
log for the use the user space that is concatenated from these two
partial event logs [2]"
[1] https://trustedcomputinggroup.org/resource/pc-client-specific-platform-firmware-profile-specification/
[2] The final concatenation is done in drivers/char/tpm/eventlog/efi.c
* tag 'tpmdd-next-20190625' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: Don't duplicate events from the final event log in the TCG2 log
Abstract out support for locating an EFI config table
tpm: Fix TPM 1.2 Shutdown sequence to prevent future TPM operations
efi: Attempt to get the TCG2 event log in the boot stub
tpm: Append the final event log to the TPM event log
tpm: Reserve the TPM final events table
tpm: Abstract crypto agile event size calculations
tpm: Actually fail on TPM errors during "get random"
Pull SMP/hotplug updates from Thomas Gleixner:
"A small set of updates for SMP and CPU hotplug:
- Abort disabling secondary CPUs in the freezer when a wakeup is
pending instead of evaluating it only after all CPUs have been
offlined.
- Remove the shared annotation for the strict per CPU cfd_data in the
smp function call core code.
- Remove the return values of smp_call_function() and on_each_cpu()
as they are unconditionally 0. Fixup the few callers which actually
bothered to check the return value"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp: Remove smp_call_function() and on_each_cpu() return values
smp: Do not mark call_function_data as shared
cpu/hotplug: Abort disabling secondary CPUs if wakeup is pending
cpu/hotplug: Fix notify_cpu_starting() reference in bringup_wait_for_ap()
After the first call to GetEventLog() on UEFI systems using the TCG2
crypto agile log format, any further log events (other than those
triggered by ExitBootServices()) will be logged in both the main log and
also in the Final Events Log. While the kernel only calls GetEventLog()
immediately before ExitBootServices(), we can't control whether earlier
parts of the boot process have done so. This will result in log entries
that exist in both logs, and so the current approach of simply appending
the Final Event Log to the main log will result in events being
duplicated.
We can avoid this problem by looking at the size of the Final Event Log
just before we call ExitBootServices() and exporting this to the main
kernel. The kernel can then skip over all events that occured before
ExitBootServices() and only append events that were not also logged to
the main log.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reported-by: Joe Richey <joerichey@google.com>
Suggested-by: Joe Richey <joerichey@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Any events that are logged after GetEventsLog() is called are logged to
the EFI Final Events table. These events are defined as being in the
crypto agile log format, so we can just append them directly to the
existing log if it's in the same format. In theory we can also construct
old-style SHA1 log entries for devices that only return logs in that
format, but EDK2 doesn't generate the final event log in that case so
it doesn't seem worth it at the moment.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reviewed-by: Bartosz Szczepanek <bsz@semihalf.com>
Tested-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
UEFI systems provide a boot services protocol for obtaining the TPM
event log, but this is unusable after ExitBootServices() is called.
Unfortunately ExitBootServices() itself triggers additional TPM events
that then can't be obtained using this protocol. The platform provides a
mechanism for the OS to obtain these events by recording them to a
separate UEFI configuration table which the OS can then map.
Unfortunately this table isn't self describing in terms of providing its
length, so we need to parse the events inside it to figure out how long
it is. Since the table isn't mapped at this point, we need to extend the
length calculation function to be able to map the event as it goes
along.
(Fixes by Bartosz Szczepanek <bsz@semihalf.com>)
Signed-off-by: Matthew Garrett <mjg59@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Bartosz Szczepanek <bsz@semihalf.com>
Tested-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
We need to calculate the size of crypto agile events in multiple
locations, including in the EFI boot stub. The easiest way to do this is
to put it in a header file as an inline and leave a wrapper to ensure we
don't end up with multiple copies of it embedded in the existing code.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reviewed-by: Bartosz Szczepanek <bsz@semihalf.com>
Tested-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
A "get random" may fail with a TPM error, but those codes were returned
as-is to the caller, which assumed the result was the number of bytes
that had been written to the target buffer, which could lead to a kernel
heap memory exposure and over-read.
This fixes tpm1_get_random() to mask positive TPM errors into -EIO, as
before.
[ 18.092103] tpm tpm0: A TPM error (379) occurred attempting get random
[ 18.092106] usercopy: Kernel memory exposure attempt detected from SLUB object 'kmalloc-64' (offset 0, size 379)!
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1650989
Reported-by: Phil Baker <baker1tex@gmail.com>
Reported-by: Craig Robson <craig@zhatt.com>
Fixes: 7aee9c52d7 ("tpm: tpm1: rewrite tpm1_get_random() using tpm_buf structure")
Cc: Laura Abbott <labbott@redhat.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The driver_find_device() accepts a match function pointer to
filter the devices for lookup, similar to bus/class_find_device().
However, there is a minor difference in the prototype for the
match parameter for driver_find_device() with the now unified
version accepted by {bus/class}_find_device(), where it doesn't
accept a "const" qualifier for the data argument. This prevents
us from reusing the generic match functions for driver_find_device().
For this reason, change the prototype of the driver_find_device() to
make the "match" parameter in line with {bus/class}_find_device()
and adjust its callers to use the const qualifier. Also, we could
now promote the "data" parameter to const as we pass it down
as a const parameter to the match functions.
Cc: Corey Minyard <minyard@acm.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/char/ipmi/ipmb_dev_int.c:352:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 51bd6f2915 ("Add support for IPMB driver")
CC: Asmaa Mnebhi <Asmaa@mellanox.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Message-Id: <20190623185044.GA94834@lkp-kbuild21>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The return value is fixed. Remove it and amend the callers.
[ tglx: Fixup arm/bL_switcher and powerpc/rtas ]
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/20190613064813.8102-2-namit@vmware.com
BCM7211 features a RNG200 hardware random number generator block, add
support for this chip by matching the chip-specific compatible string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 1 normalized pattern(s):
gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 58 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.556988620@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i2c_client structure can be fairly large, which leads to
a warning about possible kernel stack overflow in some
configurations:
drivers/char/ipmi/ipmb_dev_int.c:115:16: error: stack frame size of 1032 bytes in function 'ipmb_write' [-Werror,-Wframe-larger-than=]
There is no real reason to even declare an i2c_client, as we can simply
call i2c_smbus_xfer() directly instead of the i2c_smbus_write_block_data()
wrapper.
Convert the ipmb_write() to use an open-coded i2c_smbus_write_block_data()
here, without changing the behavior.
It seems that there is another problem with this implementation;
when user space passes a length of more than I2C_SMBUS_BLOCK_MAX
bytes, all the rest is silently ignored. This should probably be
addressed in a separate patch, but I don't know what the intended
behavior is here.
Fixes: 51bd6f2915 ("Add support for IPMB driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Message-Id: <20190619125045.918700-1-arnd@arndb.de>
Acked-by: Asmaa Mnebhi <Asmaa@mellanox.com>
[Broke up a line >80 characters on i2c_smbus_xfer().]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
If CONFIG_I2C is m and CONFIG_I2C_SLAVE is y,
building with CONFIG_IPMB_DEVICE_INTERFACE setting to
y will fail:
drivers/char/ipmi/ipmb_dev_int.o: In function `ipmb_remove':
ipmb_dev_int.c: undefined reference to `i2c_slave_unregister'
drivers/char/ipmi/ipmb_dev_int.o: In function `ipmb_write':
ipmb_dev_int.c: undefined reference to `i2c_smbus_write_block_data'
drivers/char/ipmi/ipmb_dev_int.o: In function `ipmb_probe':
ipmb_dev_int.c: undefined reference to `i2c_slave_register'
drivers/char/ipmi/ipmb_dev_int.o: In function `ipmb_driver_init':
ipmb_dev_int.c: undefined reference to `i2c_register_driver'
drivers/char/ipmi/ipmb_dev_int.o: In function `ipmb_driver_exit':
ipmb_dev_int.c: undefined reference to `i2c_del_driver'
Add I2C Kconfig dependency to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 51bd6f2915 ("Add support for IPMB driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Message-Id: <20190612031825.24732-1-yuehaibing@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Support receiving IPMB requests on a Satellite MC from the BMC.
Once a response is ready, this driver will send back a response
to the BMC via the IPMB channel.
Signed-off-by: Asmaa Mnebhi <Asmaa@mellanox.com>
Acked-by: vadimp@mellanox.com
Message-Id: <319690553a0da2a1e80b400941341081b383e5f1.1560192707.git.Asmaa@mellanox.com>
[Move the config option to outside the ipmi msghandler, as it's not
dependent on that. Fixed one small whitespace issue.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Based on 1 normalized pattern(s):
this program is free software you can distribute it and or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope it will be useful but without any warranty
without even the implied warranty of merchantability or fitness for
a particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.872212424@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 021110
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.221098808@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the smems of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190111.946565886@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.745679586@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 only
as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.798138318@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the reference to a device found via bus_find_device()
Cc: Corey Minyard <minyard@acm.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Message-Id: <1559577023-558-3-git-send-email-suzuki.poulose@arm.com>
[Moved the put_device() to after the platform_device_unregister(), for
better style.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 107 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.615055994@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 12 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.745497013@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or
modify it under the terms of the gnu general public license as
published by the free software foundation either version 2 or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Daniel M German <dmg@turingmachine.org>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527063114.489565842@linutronix.de
Link: https://lkml.kernel.org/r/20190524100843.207819312@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlzqGSoACgkQ8vlZVpUN
gaNhqQgAiUHwKalYrZ82NwBQGnHcKcWv3JEE9vt8Bsu4fPUzirrEqYiSudvj6nHv
8uYFKHmGx7+GEWxLfwlVZzRjLlgZqa0kpyfNFEL01KFdbFsKQN4gTYvvky+OVftr
nRZ7tp66Y5hErwn/Y0wWn9WHFOykhxGi+kv5m5CFZ7MNec/b+1H2U1hXkhSt6oug
IO2wLZYLFSPXlrqfJLV7HYJ/OX1mO7g1viCNGvpRmrvLmjmO09q0/6DF3QNAvGmj
sXXu0eV+N/Ir0so0RbeN60ZeDXaoyeOZbXFlH9zfJEgkoFv+adZjT65bQEvSUWQ2
J/v4rLXd8gmCiVwOuEbCoLKebT/nbg==
=Wf1M
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fix from Ted Ts'o:
"Fix a soft lockup regression when reading from /dev/random in early
boot"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: fix soft lockup when trying to read from an uninitialized blocking pool
Fixes: eb9d1bf079: "random: only read from /dev/random after its pool has received 128 bits"
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
checkpatch.pl does not like assignment in if condition
Signed-off-by: Naveen Kumar Parna <parna.naveenkumar@gmail.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to checkpatch: EXPORT_SYMBOL(foo); should immediately follow its
function/variable.
This patch fixes the following checkpatch.pl issues in drivers/char/misc.c:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Naveen Kumar Parna <parna.naveenkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is free software you can redistribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this file is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091650.284757242@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091649.499889647@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If platform_driver_register() fails from init_ipmi_ssif(),
platform_driver_unregister() called unconditionally will
trigger following warning,
ipmi_ssif: Unable to register driver: -12
------------[ cut here ]------------
Unexpected driver unregister!
WARNING: CPU: 1 PID: 6305 at drivers/base/driver.c:193 driver_unregister+0x60/0x70 drivers/base/driver.c:193
Fix it by adding platform_registered variable, only unregister platform
driver when it is already successfully registered.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Message-Id: <20190524143724.43218-1-wangkefeng.wang@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not write to the free software foundation 675
mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.342335923@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cover 'int' to 'bool' type for initialized variable.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Message-Id: <20190517101245.4341-2-wangkefeng.wang@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
If ipmi_si_platform_init()->platform_driver_register() fails,
platform_driver_unregister() called unconditionally will trigger
following warning,
ipmi_platform: Unable to register driver: -12
------------[ cut here ]------------
Unexpected driver unregister!
WARNING: CPU: 1 PID: 7210 at drivers/base/driver.c:193 driver_unregister+0x60/0x70 drivers/base/driver.c:193
Fix it by adding platform_registered variable, only unregister platform
driver when it is already successfully registered.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Message-Id: <20190517101245.4341-1-wangkefeng.wang@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
-----BEGIN PGP SIGNATURE-----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=v2pN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.2' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Some minor cleanups for the IPMI driver"
* tag 'for-linus-5.2' of git://github.com/cminyard/linux-ipmi:
ipmi: Remove warning if no slave address is present
ipmi:ssif: Only unregister the platform driver if it was registered
ipmi:ssif: compare block number correctly for multi-part return messages
ipmi: Add the i2c-addr property for SSIF interfaces
char/ipmi: fix spelling mistake "receieved_messages" -> "received_messages"
ipmi: avoid atomic_inc in exit function
ipmi: Remove file from ipmi_file_private
ipmi_si: remove an unused variable in try_smi_init()
ipmi: Make ipmi_interfaces_srcu variable static
Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKvrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynR2wCfTrWM9Qm7oA1hgWeYZiLTrnYnOtsAoK4a629W
o7AAyVf8RJ4jdWaSgOqx
=9Dy/
-----END PGP SIGNATURE-----
Merge tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits)
tty: serial: add driver for the SiFive UART
dt-bindings: serial: add documentation for the SiFive UART driver
serial: uartps: Add support for cts-override
dt-bindings: xilinx-uartps: Add support for cts-override
serial: milbeaut_usio: Fix error handling in probe and remove
tty: rocket: deprecate the rp_ioctl
tty: rocket: Remove RCPK_GET_STRUCT ioctl
tty: update obsolete termios comment
tty: serial_core: fix error code returned by uart_register_driver()
serial: 8250-mtk: modify baudrate setting
serial: 8250-mtk: add follow control
docs: serial: convert docs to ReST and rename to *.rst
serial: 8250_exar: Adjust IOT2000 matching
TTY: serial_core, add ->install
serial: Fix using plain integer instead of Null pointer
tty:serial_core: Spelling mistake
tty: Add NULL TTY driver
tty: vt: keyboard: Allow Unicode compose base char
Revert "tty: fix NULL pointer issue when tty_port ops is not set"
serial: Add Milbeaut serial control
...
trust the CPU's RNG on NUMA systems; other miscellaneous cleanups and
fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlzSEyoACgkQ8vlZVpUN
gaPJKAf/cBOEU9Zn0PzdCiybl6IT88A/EcL2FPPFbMrRI/aUDZ6jBURsa2Ds0+Rb
XiMjElnxMGSv03P+MTo0SPTVwYLGPpvNgplL25I4HMfKUPbpAdxk5UZS9pUllv2T
3ftQfGgdDalewlT8BH0K5EY9E8Whe9ODrLgGq6jXgXHm2sssDzPF+pB2ySuDRvsA
W/6rF+PW4n/2n3An6h9jc/0cShurarpHjvWzuFWY3Mevgrl53r8SppIt085/5K6A
tsSdXIqIBvhCp9OvXBHzEDCEPpdVBlL81XauIu6uMSlJ/oofOqjJs2Ib1k04Xx9z
dp4/7REfm/HFMyT9MNAYPmhmXruiiQ==
=56QI
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness updates from Ted Ts'o:
- initialize the random driver earler
- fix CRNG initialization when we trust the CPU's RNG on NUMA systems
- other miscellaneous cleanups and fixes.
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: add a spinlock_t to struct batched_entropy
random: document get_random_int() family
random: fix CRNG initialization when random.trust_cpu=1
random: move rand_initialize() earlier
random: only read from /dev/random after its pool has received 128 bits
drivers/char/random.c: make primary_crng static
drivers/char/random.c: remove unused stuct poolinfo::poolbits
drivers/char/random.c: constify poolinfo_table
Here is the "real" big set of char/misc driver patches for 5.2-rc1
Loads of different driver subsystem stuff in here, all over the places:
- thunderbolt driver updates
- habanalabs driver updates
- nvmem driver updates
- extcon driver updates
- intel_th driver updates
- mei driver updates
- coresight driver updates
- soundwire driver cleanups and updates
- fastrpc driver updates
- other minor driver updates
- chardev minor fixups
Feels like this tree is getting to be a dumping ground of "small driver
subsystems" these days. Which is fine with me, if it makes things
easier for those subsystem maintainers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHE2w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvyQCYj5vSHQ88yEU+bzwGzQQLOBWYIwCgm5Iku0Y3
f6V3MvRffg4qUp3cGbU=
=R37j
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc update part 2 from Greg KH:
"Here is the "real" big set of char/misc driver patches for 5.2-rc1
Loads of different driver subsystem stuff in here, all over the places:
- thunderbolt driver updates
- habanalabs driver updates
- nvmem driver updates
- extcon driver updates
- intel_th driver updates
- mei driver updates
- coresight driver updates
- soundwire driver cleanups and updates
- fastrpc driver updates
- other minor driver updates
- chardev minor fixups
Feels like this tree is getting to be a dumping ground of "small
driver subsystems" these days. Which is fine with me, if it makes
things easier for those subsystem maintainers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
intel_th: msu: Add current window tracking
intel_th: msu: Add a sysfs attribute to trigger window switch
intel_th: msu: Correct the block wrap detection
intel_th: Add switch triggering support
intel_th: gth: Factor out trace start/stop
intel_th: msu: Factor out pipeline draining
intel_th: msu: Switch over to scatterlist
intel_th: msu: Replace open-coded list_{first,last,next}_entry variants
intel_th: Only report useful IRQs to subdevices
intel_th: msu: Start handling IRQs
intel_th: pci: Use MSI interrupt signalling
intel_th: Communicate IRQ via resource
intel_th: Add "rtit" source device
intel_th: Skip subdevices if their MMIO is missing
intel_th: Rework resource passing between glue layers and core
intel_th: SPDX-ify the documentation
intel_th: msu: Fix single mode with IOMMU
coresight: funnel: Support static funnel
dt-bindings: arm: coresight: Unify funnel DT binding
coresight: replicator: Add new device id for static replicator
...
-----BEGIN PGP SIGNATURE-----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=LH11
-----END PGP SIGNATURE-----
Merge tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"This patchset makes it possible to retrieve pidfds at process creation
time by introducing the new flag CLONE_PIDFD to the clone() system
call. Linus originally suggested to implement this as a new flag to
clone() instead of making it a separate system call.
After a thorough review from Oleg CLONE_PIDFD returns pidfds in the
parent_tidptr argument. This means we can give back the associated pid
and the pidfd at the same time. Access to process metadata information
thus becomes rather trivial.
As has been agreed, CLONE_PIDFD creates file descriptors based on
anonymous inodes similar to the new mount api. They are made
unconditional by this patchset as they are now needed by core kernel
code (vfs, pidfd) even more than they already were before (timerfd,
signalfd, io_uring, epoll etc.). The core patchset is rather small.
The bulky looking changelist is caused by David's very simple changes
to Kconfig to make anon inodes unconditional.
A pidfd comes with additional information in fdinfo if the kernel
supports procfs. The fdinfo file contains the pid of the process in
the callers pid namespace in the same format as the procfs status
file, i.e. "Pid:\t%d".
To remove worries about missing metadata access this patchset comes
with a sample/test program that illustrates how a combination of
CLONE_PIDFD and pidfd_send_signal() can be used to gain race-free
access to process metadata through /proc/<pid>.
Further work based on this patchset has been done by Joel. His work
makes pidfds pollable. It finished too late for this merge window. I
would prefer to have it sitting in linux-next for a while and send it
for inclusion during the 5.3 merge window"
* tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
samples: show race-free pidfd metadata access
signal: support CLONE_PIDFD with pidfd_send_signal
clone: add CLONE_PIDFD
Make anon_inodes unconditional
https://lore.kernel.org/linux-fsdevel/CAHk-=wg1tFzcaX2v9Z91vPJiBR486ddW5MtgDL02-fOen2F0Aw@mail.gmail.com/T/#m5b2d9ad3aeacea4bd6aa1964468ac074bf3aa5bf
-----BEGIN PGP SIGNATURE-----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=Mavg
-----END PGP SIGNATURE-----
Merge tag 'stream_open-5.2' of https://lab.nexedi.com/kirr/linux
Pull stream_open conversion from Kirill Smelkov:
- remove unnecessary double nonseekable_open from drivers/char/dtlk.c
as noticed by Pavel Machek while reviewing nonseekable_open ->
stream_open mass conversion.
- the mass conversion patch promised in commit 10dce8af34 ("fs:
stream_open - opener for stream-like files so that read and write can
run simultaneously without deadlock") and is automatically generated
by running
$ make coccicheck MODE=patch COCCI=scripts/coccinelle/api/stream_open.cocci
I've verified each generated change manually - that it is correct to
convert - and each other nonseekable_open instance left - that it is
either not correct to convert there, or that it is not converted due
to current stream_open.cocci limitations. More details on this in the
patch.
- finally, change VFS to pass ppos=NULL into .read/.write for files
that declare themselves streams. It was suggested by Rasmus Villemoes
and makes sure that if ppos starts to be erroneously used in a stream
file, such bug won't go unnoticed and will produce an oops instead of
creating illusion of position change being taken into account.
Note: this patch does not conflict with "fuse: Add FOPEN_STREAM to
use stream_open()" that will be hopefully coming via FUSE tree,
because fs/fuse/ uses new-style .read_iter/.write_iter, and for these
accessors position is still passed as non-pointer kiocb.ki_pos .
* tag 'stream_open-5.2' of https://lab.nexedi.com/kirr/linux:
vfs: pass ppos=NULL to .read()/.write() of FMODE_STREAM files
*: convert stream-like files from nonseekable_open -> stream_open
dtlk: remove double call to nonseekable_open
Pull crypto update from Herbert Xu:
"API:
- Add support for AEAD in simd
- Add fuzz testing to testmgr
- Add panic_on_fail module parameter to testmgr
- Use per-CPU struct instead multiple variables in scompress
- Change verify API for akcipher
Algorithms:
- Convert x86 AEAD algorithms over to simd
- Forbid 2-key 3DES in FIPS mode
- Add EC-RDSA (GOST 34.10) algorithm
Drivers:
- Set output IV with ctr-aes in crypto4xx
- Set output IV in rockchip
- Fix potential length overflow with hashing in sun4i-ss
- Fix computation error with ctr in vmx
- Add SM4 protected keys support in ccree
- Remove long-broken mxc-scc driver
- Add rfc4106(gcm(aes)) cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (179 commits)
crypto: ccree - use a proper le32 type for le32 val
crypto: ccree - remove set but not used variable 'du_size'
crypto: ccree - Make cc_sec_disable static
crypto: ccree - fix spelling mistake "protedcted" -> "protected"
crypto: caam/qi2 - generate hash keys in-place
crypto: caam/qi2 - fix DMA mapping of stack memory
crypto: caam/qi2 - fix zero-length buffer DMA mapping
crypto: stm32/cryp - update to return iv_out
crypto: stm32/cryp - remove request mutex protection
crypto: stm32/cryp - add weak key check for DES
crypto: atmel - remove set but not used variable 'alg_name'
crypto: picoxcell - Use dev_get_drvdata()
crypto: crypto4xx - get rid of redundant using_sd variable
crypto: crypto4xx - use sync skcipher for fallback
crypto: crypto4xx - fix cfb and ofb "overran dst buffer" issues
crypto: crypto4xx - fix ctr-aes missing output IV
crypto: ecrdsa - select ASN1 and OID_REGISTRY for EC-RDSA
crypto: ux500 - use ccflags-y instead of CFLAGS_<basename>.o
crypto: ccree - handle tee fips error during power management resume
crypto: ccree - add function to handle cryptocell tee fips error
...
Using scripts/coccinelle/api/stream_open.cocci added in 10dce8af34
("fs: stream_open - opener for stream-like files so that read and write
can run simultaneously without deadlock"), search and convert to
stream_open all in-kernel nonseekable_open users for which read and
write actually do not depend on ppos and where there is no other methods
in file_operations which assume @offset access.
I've verified each generated change manually - that it is correct to convert -
and each other nonseekable_open instance left - that it is either not correct
to convert there, or that it is not converted due to current stream_open.cocci
limitations. The script also does not convert files that should be valid to
convert, but that currently have .llseek = noop_llseek or generic_file_llseek
for unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Among cases converted 14 were potentially vulnerable to read vs write deadlock
(see details in 10dce8af34):
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/infiniband/core/user_mad.c:988:1-17: ERROR: umad_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/misc/uinput.c:401:1-17: ERROR: uinput_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
and the rest were just safe to convert to stream_open because their read and
write do not use ppos at all and corresponding file_operations do not
have methods that assume @offset file access(*):
arch/powerpc/platforms/52xx/mpc52xx_gpt.c:631:8-24: WARNING: mpc52xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/um/drivers/harddog_kern.c:88:8-24: WARNING: harddog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/x86/kernel/cpu/microcode/core.c:430:33-49: WARNING: microcode_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ds1620.c:215:8-24: WARNING: ds1620_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/dtlk.c:301:1-17: WARNING: dtlk_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ipmi/ipmi_watchdog.c:840:9-25: WARNING: ipmi_wdog_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/pcmcia/scr24x_cs.c:95:8-24: WARNING: scr24x_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/tb0219.c:246:9-25: WARNING: tb0219_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/firewire/nosy.c:306:8-24: WARNING: nosy_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/fschmd.c:840:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/w83793.c:1344:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucma.c:1747:8-24: WARNING: ucma_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucm.c:1178:8-24: WARNING: ucm_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/uverbs_main.c:1086:8-24: WARNING: uverbs_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/input/joydev.c:282:1-17: WARNING: joydev_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/pci/switch/switchtec.c:393:1-17: WARNING: switchtec_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/platform/chrome/cros_ec_debugfs.c:135:8-24: WARNING: cros_ec_console_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-ds1374.c:470:9-25: WARNING: ds1374_wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-m41t80.c:805:9-25: WARNING: wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/tape_char.c:293:2-18: WARNING: tape_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/zcore.c:194:8-24: WARNING: zcore_reipl_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/crypto/zcrypt_api.c:528:8-24: WARNING: zcrypt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/spi/spidev.c:594:1-17: WARNING: spidev_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/staging/pi433/pi433_if.c:974:1-17: WARNING: pi433_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/acquirewdt.c:203:8-24: WARNING: acq_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/advantechwdt.c:202:8-24: WARNING: advwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim1535_wdt.c:252:8-24: WARNING: ali_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim7101_wdt.c:217:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ar7_wdt.c:166:8-24: WARNING: ar7_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/at91rm9200_wdt.c:113:8-24: WARNING: at91wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ath79_wdt.c:135:8-24: WARNING: ath79_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/bcm63xx_wdt.c:119:8-24: WARNING: bcm63xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpu5wdt.c:143:8-24: WARNING: cpu5wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpwd.c:397:8-24: WARNING: cpwd_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/eurotechwdt.c:319:8-24: WARNING: eurwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/f71808e_wdt.c:528:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/gef_wdt.c:232:8-24: WARNING: gef_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/geodewdt.c:95:8-24: WARNING: geodewdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ib700wdt.c:241:8-24: WARNING: ibwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ibmasr.c:326:8-24: WARNING: asr_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/indydog.c:80:8-24: WARNING: indydog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/intel_scu_watchdog.c:307:8-24: WARNING: intel_scu_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/iop_wdt.c:104:8-24: WARNING: iop_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/it8712f_wdt.c:330:8-24: WARNING: it8712f_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ixp4xx_wdt.c:68:8-24: WARNING: ixp4xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ks8695_wdt.c:145:8-24: WARNING: ks8695wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/m54xx_wdt.c:88:8-24: WARNING: m54xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/machzwd.c:336:8-24: WARNING: zf_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mixcomwd.c:153:8-24: WARNING: mixcomwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mtx-1_wdt.c:121:8-24: WARNING: mtx1_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mv64x60_wdt.c:136:8-24: WARNING: mv64x60_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nuc900_wdt.c:134:8-24: WARNING: nuc900wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nv_tco.c:164:8-24: WARNING: nv_tco_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pc87413_wdt.c:289:8-24: WARNING: pc87413_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:698:8-24: WARNING: pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:737:8-24: WARNING: pcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:581:8-24: WARNING: pcipcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:623:8-24: WARNING: pcipcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:488:8-24: WARNING: usb_pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:527:8-24: WARNING: usb_pcwd_temperature_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pika_wdt.c:121:8-24: WARNING: pikawdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pnx833x_wdt.c:119:8-24: WARNING: pnx833x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rc32434_wdt.c:153:8-24: WARNING: rc32434_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rdc321x_wdt.c:145:8-24: WARNING: rdc321x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/riowd.c:79:1-17: WARNING: riowd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sa1100_wdt.c:62:8-24: WARNING: sa1100dog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc60xxwdt.c:211:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc7240_wdt.c:139:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc8360.c:274:8-24: WARNING: sbc8360_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_epx_c3.c:81:8-24: WARNING: epx_c3_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_fitpc2_wdt.c:78:8-24: WARNING: fitpc2_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sb_wdog.c:108:1-17: WARNING: sbwdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc1200wdt.c:181:8-24: WARNING: sc1200wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc520_wdt.c:261:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sch311x_wdt.c:319:8-24: WARNING: sch311x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/scx200_wdt.c:105:8-24: WARNING: scx200_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/smsc37b787_wdt.c:369:8-24: WARNING: wb_smsc_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83877f_wdt.c:227:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83977f_wdt.c:301:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wafer5823wdt.c:200:8-24: WARNING: wafwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/watchdog_dev.c:828:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:379:8-24: WARNING: wdrtas_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:445:8-24: WARNING: wdrtas_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt285.c:104:1-17: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt977.c:276:8-24: WARNING: wdt977_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:424:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:484:8-24: WARNING: wdt_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:464:8-24: WARNING: wdtpci_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:527:8-24: WARNING: wdtpci_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
net/batman-adv/log.c:105:1-17: WARNING: batadv_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/control.c:57:7-23: WARNING: snd_ctl_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/rawmidi.c:385:7-23: WARNING: snd_rawmidi_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/seq/seq_clientmgr.c:310:7-23: WARNING: snd_seq_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/timer.c:1428:7-23: WARNING: snd_timer_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
One can also recheck/review the patch via generating it with explanation comments included via
$ make coccicheck MODE=patch COCCI=scripts/coccinelle/api/stream_open.cocci SPFLAGS="-D explain"
(*) This second group also contains cases with read/write deadlocks that
stream_open.cocci don't yet detect, but which are still valid to convert to
stream_open since ppos is not used. For example drivers/pci/switch/switchtec.c
calls wait_for_completion_interruptible() in its .read, but stream_open.cocci
currently detects only "wait_event*" as blocking.
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yongzhi Pan <panyongzhi@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Nikolaus Rath <Nikolaus@rath.org>
Cc: Han-Wen Nienhuys <hanwen@google.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James R. Van Zandt" <jrv@vanzandt.mv.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk> [scr24x_cs]
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Jean Delvare <jdelvare@suse.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> [watchdog/* hwmon/*]
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com> [drivers/pci/switch/switchtec]
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [drivers/pci/switch/switchtec]
Cc: Benson Leung <bleung@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> [platform/chrome]
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> [rtc/*]
Cc: Mark Brown <broonie@kernel.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Zwane Mwaikambo <zwanem@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
dtlk_open currently has 2 calls to nonseekable_open which are both
executed on success path. It was not hurting to make the extra call as
nonseekable_open is only changing file->f_flags in idempotent way.
However the first nonseekable_open is indeed both unneeded and looks
suspicious.
The first nonseekable_open was added in 6244f13c51 ("Fix up a couple of
drivers - notable sg - for nonseekability."; 2004-Aug-7). The second
nonseekable_open call was introduced in dc5c724584 ("Remove ESPIPE logic
from drivers, letting the VFS layer handle it instead.; 2004-Aug-8). The
latter patch being mass change probably missed to remove
nonseekable_open that was introduced into dtlk_open the day before.
Fix it: remove the extra/unneeded nonseekable_open call and leave the
call to nonseekable_open only on the path where we are actually opening
the file.
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
It's just noise, really, lots of systems don't have it.
Reported-by: Kamlakant Patel <kamlakantp@marvell.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
According to ipmi spec, block number is a number that is incremented,
starting with 0, for each new block of message data returned using the
middle transaction.
Here, the 'blocknum' is data[0] which always starts from zero(0) and
'ssif_info->multi_pos' starts from 1.
So, we need to add +1 to blocknum while comparing with multi_pos.
Fixes: 7d6380cd40 ("ipmi:ssif: Fix handling of multi-part return messages").
Reported-by: Kiran Kolukuluru <kirank@ami.com>
Signed-off-by: Kamlakant Patel <kamlakantp@marvell.com>
Message-Id: <1556106615-18722-1-git-send-email-kamlakantp@marvell.com>
[Also added a debug log if the block numbers don't match.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 4.4
This is required for SSIF to work.
There was no way to know if the interface being added was SI
or SSIF from the platform data, but that was required so the
i2c-addr is only added for SSIF interfaces. So add a field
for that.
Also rework the logic a bit so that ipmi-type is not set
for SSIF interfaces, as it is not necessary for that.
Fixes: 3cd83bac48 ("ipmi: Consolidate the adding of platform devices")
Reported-by: Kamlakant Patel <kamlakantp@marvell.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 5.1
The per-CPU variable batched_entropy_uXX is protected by get_cpu_var().
This is just a preempt_disable() which ensures that the variable is only
from the local CPU. It does not protect against users on the same CPU
from another context. It is possible that a preemptible context reads
slot 0 and then an interrupt occurs and the same value is read again.
The above scenario is confirmed by lockdep if we add a spinlock:
| ================================
| WARNING: inconsistent lock state
| 5.1.0-rc3+ #42 Not tainted
| --------------------------------
| inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
| ksoftirqd/9/56 [HC0[0]:SC1[1]:HE0:SE0] takes:
| (____ptrval____) (batched_entropy_u32.lock){+.?.}, at: get_random_u32+0x3e/0xe0
| {SOFTIRQ-ON-W} state was registered at:
| _raw_spin_lock+0x2a/0x40
| get_random_u32+0x3e/0xe0
| new_slab+0x15c/0x7b0
| ___slab_alloc+0x492/0x620
| __slab_alloc.isra.73+0x53/0xa0
| kmem_cache_alloc_node+0xaf/0x2a0
| copy_process.part.41+0x1e1/0x2370
| _do_fork+0xdb/0x6d0
| kernel_thread+0x20/0x30
| kthreadd+0x1ba/0x220
| ret_from_fork+0x3a/0x50
…
| other info that might help us debug this:
| Possible unsafe locking scenario:
|
| CPU0
| ----
| lock(batched_entropy_u32.lock);
| <Interrupt>
| lock(batched_entropy_u32.lock);
|
| *** DEADLOCK ***
|
| stack backtrace:
| Call Trace:
…
| kmem_cache_alloc_trace+0x20e/0x270
| ipmi_alloc_recv_msg+0x16/0x40
…
| __do_softirq+0xec/0x48d
| run_ksoftirqd+0x37/0x60
| smpboot_thread_fn+0x191/0x290
| kthread+0xfe/0x130
| ret_from_fork+0x3a/0x50
Add a spinlock_t to the batched_entropy data structure and acquire the
lock while accessing it. Acquire the lock with disabled interrupts
because this function may be used from interrupt context.
Remove the batched_entropy_reset_lock lock. Now that we have a lock for
the data scructure, we can access it from a remote CPU.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Explain what these functions are for and when they offer
an advantage over get_random_bytes().
(We still need documentation on rng_is_initialized(), the
random_ready_callback system, and early boot in general.)
Signed-off-by: George Spelvin <lkml@sdf.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When the system boots with random.trust_cpu=1 it doesn't initialize the
per-NUMA CRNGs because it skips the rest of the CRNG startup code. This
means that the code from 1e7f583af6 ("random: make /dev/urandom scalable
for silly userspace programs") is not used when random.trust_cpu=1.
crash> dmesg | grep random:
[ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x530 with crng_init=0
[ 0.314029] random: crng done (trusting CPU's manufacturer)
crash> print crng_node_pool
$6 = (struct crng_state **) 0x0
After adding the missing call to numa_crng_init() the per-NUMA CRNGs are
initialized again:
crash> dmesg | grep random:
[ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x530 with crng_init=0
[ 0.314031] random: crng done (trusting CPU's manufacturer)
crash> print crng_node_pool
$1 = (struct crng_state **) 0xffff9a915f4014a0
The call to invalidate_batched_entropy() was also missing. This is
important for architectures like PPC and S390 which only have the
arch_get_random_seed_* functions.
Fixes: 39a8883a2b ("random: add a config option to trust the CPU's hwrng")
Signed-off-by: Jon DeVree <nuxi@vault24.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Right now rand_initialize() is run as an early_initcall(), but it only
depends on timekeeping_init() (for mixing ktime_get_real() into the
pools). However, the call to boot_init_stack_canary() for stack canary
initialization runs earlier, which triggers a warning at boot:
random: get_random_bytes called from start_kernel+0x357/0x548 with crng_init=0
Instead, this moves rand_initialize() to after timekeeping_init(), and moves
canary initialization here as well.
Note that this warning may still remain for machines that do not have
UEFI RNG support (which initializes the RNG pools during setup_arch()),
or for x86 machines without RDRAND (or booting without "random.trust=on"
or CONFIG_RANDOM_TRUST_CPU=y).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Make the anon_inodes facility unconditional so that it can be used by core
VFS code and pidfd code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[christian@brauner.io: adapt commit message to mention pidfds]
Signed-off-by: Christian Brauner <christian@brauner.io>
This causes a link failure on ARM in certain configurations,
when we reference each atomic operation from .alt.smp.init in
order to patch out atomics on non-SMP systems:
`.exit.text' referenced in section `.alt.smp.init' of drivers/char/ipmi/ipmi_msghandler.o: defined in discarded section `.exit.text' of drivers/char/ipmi/ipmi_msghandler.o
In this case, we can trivially replace the atomic_inc() with
an atomic_set() that has the same effect and does not require
a fixup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Message-Id: <20190415155509.3565087-1-arnd@arndb.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The "init_name" variable isn't used any more after commit 90b2d4f15f
("ipmi_si: Remove hacks for adding a dummy platform devices").
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20190322065426.GB12551@kadam>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Fix sparse warning:
drivers/char/ipmi/ipmi_msghandler.c:635:20: warning:
symbol 'ipmi_interfaces_srcu' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Message-Id: <20190320133505.21984-1-yuehaibing@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Immediately after boot, we allow reads from /dev/random before its
entropy pool has been fully initialized. Fix this so that we don't
allow this until the blocking pool has received 128 bits.
We do this by repurposing the initialized flag in the entropy pool
struct, and use the initialized flag in the blocking pool to indicate
whether it is safe to pull from the blocking pool.
To do this, we needed to rework when we decide to push entropy from the
input pool to the blocking pool, since the initialized flag for the
input pool was used for this purpose. To simplify things, we no
longer use the initialized flag for that purpose, nor do we use the
entropy_total field any more.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since the definition of struct crng_state is private to random.c, and
primary_crng is neither declared or used elsewhere, there's no reason
for that symbol to have external linkage.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This field is never used, might as well remove it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Never modified, might as well be put in .rodata.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The intended behavior of function ipmi_hardcode_init_one() is to default
to kcs interface when no type argument is presented when initializing
ipmi with hard coded addresses.
However, the array of char pointers allocated on the stack by function
ipmi_hardcode_init() was not inited to zeroes, so it contained stack
debris.
Consequently, passing the cruft stored in this array to function
ipmi_hardcode_init_one() caused a crash when it was unable to detect
that the char * being passed was nonsense and tried to access the
address specified by the bogus pointer.
The fix is simply to initialize the si_type array to zeroes, so if
there were no type argument given to at the command line, function
ipmi_hardcode_init_one() could properly default to the kcs interface.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Message-Id: <1554837603-40299-1-git-send-email-tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
An extra memset was put into a place that cleared the interface
type.
Reported-by: Tony Camuso <tcamuso@redhat.com>
Fixes: 3cd83bac48 ("ipmi: Consolidate the adding of platform devices")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Add a default quality to hw_random device to be
automatically set as new default entropy. Setting
random quality will decrease the crng init time by
switching to this hardware random source.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No remove function implemented yet in the driver.
Without remove function, the pm_runtime implementation
complains when removing and probing again the driver.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
calc_tpm2_event_size() has an invalid signature because
it returns a 'size_t' where as its signature says that
it returns 'int'.
Cc: <stable@vger.kernel.org>
Fixes: 4d23cc323c ("tpm: add securityfs support for TPM 2.0 firmware event log")
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
The poll condition should only check response_length,
because reads should only be issued if there is data to read.
The response_read flag only prevents double writes.
The problem was that the write set the response_read to false,
enqued a tpm job, and returned. Then application called poll
which checked the response_read flag and returned EPOLLIN.
Then the application called read, but got nothing.
After all that the async_work kicked in.
Added also mutex_lock around the poll check to prevent
other possible race conditions.
Fixes: 9488585b21 ("tpm: add support for partial reads")
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
tpm_chip_start/stop() should be also called for TPM 1.x devices on
suspend. Add that functionality back. Do not lock the chip because
it is unnecessary as there are no multiple threads using it when
doing the suspend.
Fixes: a3fbfae82b ("tpm: take TPM chip power gating out of tpm_transmit()")
Reported-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
The n_r3964 line discipline driver was written in a different time, when
SMP machines were rare, and users were trusted to do the right thing.
Since then, the world has moved on but not this code, it has stayed
rooted in the past with its lovely hand-crafted list structures and
loads of "interesting" race conditions all over the place.
After attempting to clean up most of the issues, I just gave up and am
now marking the driver as BROKEN so that hopefully someone who has this
hardware will show up out of the woodwork (I know you are out there!)
and will help with debugging a raft of changes that I had laying around
for the code, but was too afraid to commit as odds are they would break
things.
Many thanks to Jann and Linus for pointing out the initial problems in
this codebase, as well as many reviews of my attempts to fix the issues.
It was a case of whack-a-mole, and as you can see, the mole won.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check if ioremap fails, and if so, return AE_ERROR.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For regular serial ports we do not initialize value of vtermno
variable. A garbage value is assigned for non console ports.
The value can be observed as a random integer with [1].
[1] vim /sys/kernel/debug/virtio-ports/vport*p*
This patch initialize the value of vtermno for console serial
ports to '1' and regular serial ports are initiaized to '0'.
Reported-by: siliu@redhat.com
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer combinations of the glibc, kernel and openssh can result in long initial
startup times on OMAP devices:
[ 6.671425] systemd-rc-once[102]: Creating ED25519 key; this may take some time ...
[ 142.652491] systemd-rc-once[102]: Creating ED25519 key; done.
due to the blocking getrandom(2) system call:
[ 142.610335] random: crng init done
Set the quality level for the omap hwrng driver allowing the kernel to use the
hwrng as an entropy source at boot.
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull tpm updates from James Morris:
- Clean up the transmission flow
Cleaned up the whole transmission flow. Locking of the chip is now
done in the level of tpm_try_get_ops() and tpm_put_ops() instead
taking the chip lock inside tpm_transmit(). The nested calls inside
tpm_transmit(), used with the resource manager, have been refactored
out.
Should make easier to perform more complex transactions with the TPM
without making the subsystem a bigger mess (e.g. encrypted channel
patches by James Bottomley).
- PPI 1.3 support
TPM PPI 1.3 introduces an additional optional command parameter that
may be needed for some commands. Display the parameter if the command
requires such a parameter. Only command 23 (SetPCRBanks) needs one.
The PPI request file will show output like this then:
# echo "23 16" > request
# cat request
23 16
# echo "5" > request
# cat request
5
- Extend all PCR banks in IMA
Instead of static PCR banks array, the array of available PCR banks
is now allocated dynamically. The digests sizes are determined
dynamically using a probe PCR read without relying crypto's static
list of hash algorithms.
This should finally make sealing of measurements in IMA safe and
secure.
- TPM 2.0 selftests
Added a test suite to tools/testing/selftests/tpm2 previously outside
of the kernel tree: https://github.com/jsakkine-intel/tpm2-scripts
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (37 commits)
tpm/ppi: Enable submission of optional command parameter for PPI 1.3
tpm/ppi: Possibly show command parameter if TPM PPI 1.3 is used
tpm/ppi: Display up to 101 operations as define for version 1.3
tpm/ppi: rename TPM_PPI_REVISION_ID to TPM_PPI_REVISION_ID_1
tpm/ppi: pass function revision ID to tpm_eval_dsm()
tpm: pass an array of tpm_extend_digest structures to tpm_pcr_extend()
KEYS: trusted: explicitly use tpm_chip structure from tpm_default_chip()
tpm: move tpm_chip definition to include/linux/tpm.h
tpm: retrieve digest size of unknown algorithms with PCR read
tpm: rename and export tpm2_digest and tpm2_algorithms
tpm: dynamically allocate the allocated_banks array
tpm: remove @flags from tpm_transmit()
tpm: take TPM chip power gating out of tpm_transmit()
tpm: introduce tpm_chip_start() and tpm_chip_stop()
tpm: remove TPM_TRANSMIT_UNLOCKED flag
tpm: use tpm_try_get_ops() in tpm-sysfs.c.
tpm: remove @space from tpm_transmit()
tpm: move TPM space code out of tpm_transmit()
tpm: move tpm_validate_commmand() to tpm2-space.c
tpm: clean up tpm_try_transmit() error handling flow
...
* Fix a use after free error in a certain error situation.
* Fix some flag handling issues in the SSIF (I2C) IPMI driver.
* A bunch of cleanups, spacing issues, converting pr_xxx to dev_xxx,
use standard UUID handling, and some other minor stuff.
* The IPMI code was creating a platform device if none was supplied.
Instead of doing that, have every source that creates an IPMI
device supply a device struct. This fixes several issues,including
a crash in one situation, and cleans things up a bit.
-----BEGIN PGP SIGNATURE-----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=LSch
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.1' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A couple of bug fixes and a bunch of code cleanup:
- Fix a use after free error in a certain error situation.
- Fix some flag handling issues in the SSIF (I2C) IPMI driver.
- A bunch of cleanups, spacing issues, converting pr_xxx to dev_xxx,
use standard UUID handling, and some other minor stuff.
- The IPMI code was creating a platform device if none was supplied.
Instead of doing that, have every source that creates an IPMI
device supply a device struct. This fixes several issues,including
a crash in one situation, and cleans things up a bit"
* tag 'for-linus-5.1' of git://github.com/cminyard/linux-ipmi:
ipmi_si: Potential array underflow in hotmod_handler()
ipmi_si: Remove hacks for adding a dummy platform devices
ipmi_si: Consolidate scanning the platform bus
ipmi_si: Remove hotmod devices on removal and exit
ipmi_si: Remove hardcode IPMI devices by scanning the platform bus
ipmi_si: Switch hotmod to use a platform device
ipmi: Consolidate the adding of platform devices
ipmi_si: Rename addr_type to addr_space to match what it does
ipmi_si: Convert some types into unsigned
ipmi_si: Fix crash when using hard-coded device
ipmi: Use dedicated API for copying a UUID
ipmi: Use defined constant for UUID representation
ipmi:ssif: Change some pr_xxx to dev_xxx calls
ipmi: kcs_bmc: handle devm_kasprintf() failure case
ipmi: Fix return value when a message is truncated
ipmi: clean an indentation issue, remove extraneous space
ipmi: Make the smi watcher be disabled immediately when not needed
ipmi: Fix how the lower layers are told to watch for messages
ipmi: Fix SSIF flag requests
ipmi_si: fix use-after-free of resource->name
Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they asked
me to do as the MEI driver is starting to interact with the i915 driver,
and it needed some coordination. All of those patches have been
properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+dPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym1fACgvpZAxjNzoRQJ6f06tc8ujtPk9rUAnR+tCtrZ
9e3l7H76oe33o96Qjhor
=8A2k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
Merge misc updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (159 commits)
tools/testing/selftests/proc/proc-self-syscall.c: remove duplicate include
proc: more robust bulk read test
proc: test /proc/*/maps, smaps, smaps_rollup, statm
proc: use seq_puts() everywhere
proc: read kernel cpu stat pointer once
proc: remove unused argument in proc_pid_lookup()
fs/proc/thread_self.c: code cleanup for proc_setup_thread_self()
fs/proc/self.c: code cleanup for proc_setup_self()
proc: return exit code 4 for skipped tests
mm,mremap: bail out earlier in mremap_to under map pressure
mm/sparse: fix a bad comparison
mm/memory.c: do_fault: avoid usage of stale vm_area_struct
writeback: fix inode cgroup switching comment
mm/huge_memory.c: fix "orig_pud" set but not used
mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC
mm/memcontrol.c: fix bad line in comment
mm/cma.c: cma_declare_contiguous: correct err handling
mm/page_ext.c: fix an imbalance with kmemleak
mm/compaction: pass pgdat to too_many_isolated() instead of zone
mm: remove zone_lru_lock() function, access ->lru_lock directly
...
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
Patch series "mm: PG_reserved cleanups and documentation", v2.
I was recently going over all users of PG_reserved. Short story: it is
difficult and sometimes not really clear if setting/checking for
PG_reserved is only a relict from the past. Easy to break things. I
guess I now have a pretty good idea wh things are like that nowadays and
how they evolved.
I had way more cleanups in this series inititally, but some
architectures take PG_reserved as a way to apply a different caching
strategy (for MMIO pages). So I decided to only include the most
obvious changes (that are less likely to break something). So the big
chunk of manual SetPageReserved users are MMIO/DMA related things on
device buffers.
Most notably, for device memory we will hopefully soon stop setting
PG_reserved. Then the documentation has to be updated.
This patch (of 9):
The l1 GATT page table is kept in a special on-chip page with 64
entries. We allocate the l2 page table pages via get_zeroed_page() and
enter them into the table. These l2 pages are modified accordingly when
inserting/removing memory via efficeon_insert_memory and
efficeon_remove_memory.
Apart from that, these pages are not exposed or ioremap'ed. We can stop
setting them reserved (propably copied from generic code).
Link: http://lkml.kernel.org/r/20190114125903.24845-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
BCM63XX (MIPS) does not use device tree, so there cannot be any
of_device_id, causing the driver to fail on probe:
[ 0.904564] bcm2835-rng: probe of bcm63xx-rng failed with error -22
Fix this by checking for match data only if we are probing from device
tree.
Fixes: 8705f24f7b ("hwrng: bcm2835 - Enable BCM2835 RNG to work on BCM63xx platforms")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable siz is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ival" variable needs to signed so that we don't read before the
start of the str[] array. This would only happen the user passed in a
module parameter that was just comprised of space characters.
Fixes: e80444ae4fc3 ("ipmi_si: Switch hotmod to use a platform device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20190222195530.GA306@kadam>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When a hotmod-added device is removed or when the module is removed,
remove the platform devices that was created for it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Instead of keeping track of each one, just scan the platform bus
for hardcode devices and remove them.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
It was being done in two different places now that hard-coded devices
use platform devices, and it's about to be three with hotmod switching
to platform devices. So put the code in one place.
This required some rework on some interfaces to make the type space
clean.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When excuting a command like:
modprobe ipmi_si ports=0xffc0e3 type=bt
The system would get an oops.
The trouble here is that ipmi_si_hardcode_find_bmc() is called before
ipmi_si_platform_init(), but initialization of the hard-coded device
creates an IPMI platform device, which won't be initialized yet.
The real trouble is that hard-coded devices aren't created with
any device, and the fixup is done later. So do it right, create the
hard-coded devices as normal platform devices.
This required adding some new resource types to the IPMI platform
code for passing information required by the hard-coded device
and adding some code to remove the hard-coded platform devices
on module removal.
To enforce the "hard-coded devices passed by the user take priority
over firmware devices" rule, some special code was added to check
and see if a hard-coded device already exists.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Yang Yingliang <yangyingliang@huawei.com>
Fixes the following sparse warning:
drivers/char/hw_random/optee-rng.c:265:35: warning:
symbol 'optee_rng_id_table' was not declared. Should it be static?
Fixes: 5fe8b1cc6a ("hwrng: add OP-TEE based rng driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The return from the call to tee_client_invoke_func can be a
negative error code however this is being assigned to an
unsigned variable 'ret' hence the check is always false.
Fix this by making 'ret' an int.
Detected by Coccinelle ("Unsigned expression compared with zero:
ret < 0")
Fixes: 5fe8b1cc6a ("hwrng: add OP-TEE based rng driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Clang warns:
drivers/char/hw_random/optee-rng.c:80:31: warning: suggest braces around
initialization of subobject [-Wmissing-braces]
struct tee_param param[4] = {0};
^
{}
drivers/char/hw_random/optee-rng.c:177:31: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
struct tee_param param[4] = {0};
^
{}
drivers/char/hw_random/optee-rng.c:212:48: warning: suggest braces
around initialization of subobject [-Wmissing-braces]
struct tee_ioctl_open_session_arg sess_arg = {0};
^
{}
3 warnings generated.
One way to fix these warnings is to add additional braces like Clang
suggests; however, there has been a bit of push back from some
maintainers, who just prefer memset as it is unambiguous, doesn't
depend on a particular compiler version, and properly initializes all
subobjects [1][2]. Do that here so there are no more warnings.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 5fe8b1cc6a ("hwrng: add OP-TEE based rng driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/369
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- supp_nowait flag for non-blocking tee requests
- The tee bus driver framework
- OP-TEE TEE bus device enumeration support
- An OP-TEE based rng driver
-----BEGIN PGP SIGNATURE-----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=So4a
-----END PGP SIGNATURE-----
Merge tag 'tee-bus-for-5.1' of https://git.linaro.org/people/jens.wiklander/linux-tee into arm/drivers
Introduce TEE bus driver framework
- supp_nowait flag for non-blocking tee requests
- The tee bus driver framework
- OP-TEE TEE bus device enumeration support
- An OP-TEE based rng driver
* tag 'tee-bus-for-5.1' of https://git.linaro.org/people/jens.wiklander/linux-tee:
hwrng: add OP-TEE based rng driver
tee: optee: add TEE bus device enumeration support
tee: add bus driver framework for TEE based devices
tee: add supp_nowait flag in tee_context struct
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/char/lp.c: In function ‘lp_compat_ioctl’:
drivers/char/lp.c:756:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!COMPAT_USE_64BIT_TIME) {
^
drivers/char/lp.c:761:2: note: here
case LPSETTIMEOUT_NEW:
^~~~
drivers/char/lp.c: In function ‘lp_ioctl’:
drivers/char/lp.c:728:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (BITS_PER_LONG == 32) {
^
drivers/char/lp.c:733:2: note: here
case LPSETTIMEOUT_NEW:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that in some cases, the code comment is modified in
accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables a user to specify the additional optional command
parameter by writing it into the request file:
# echo "23 16" > request
# cat request
23 16
For backwards compatibility:
If only 1 parameter is given then we assume this is the operation request
number.
# echo "5" > request
# cat request
5
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: David Safford <david.safford@ge.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
TPM PPI 1.3 introduces an additional optional command parameter
that may be needed for some commands. Display the parameter if the
command requires such a parameter. Only command 23 needs one.
The PPI request file will show output like this then:
# echo "23 16" > request
# cat request
23 16
# echo "5" > request
# cat request
5
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: David Safford <david.safford@ge.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
TPM PPI 1.3 defines operations up to number 101. We need to query up
to this number to show the user what the firmware implements.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: David Safford <david.safford@ge.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
TPM PPI 1.3 introduces a function revision 2 for some functions. So,
rename the existing TPM_PPI_REVISION_ID to TPM_PPI_REVISION_ID_1.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: David Safford <david.safford@ge.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Since we will need to pass different function revision numbers
to tpm_eval_dsm, convert this function now to take the function revision
as an additional parameter.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: David Safford <david.safford@ge.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently, tpm_pcr_extend() accepts as an input only a SHA1 digest.
This patch replaces the hash parameter of tpm_pcr_extend() with an array of
tpm_digest structures, so that the caller can provide a digest for each PCR
bank currently allocated in the TPM.
tpm_pcr_extend() will not extend banks for which no digest was provided,
as it happened before this patch, but instead it requires that callers
provide the full set of digests. Since the number of digests will always be
chip->nr_allocated_banks, the count parameter has been removed.
Due to the API change, ima_pcr_extend() and pcrlock() have been modified.
Since the number of allocated banks is not known in advance, the memory for
the digests must be dynamically allocated. To avoid performance degradation
and to avoid that a PCR extend is not done due to lack of memory, the array
of tpm_digest structures is allocated by the users of the TPM driver at
initialization time.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Mimi Zohar <zohar@linux.ibm.com> (on x86 for TPM 1.2 & PTT TPM 2.0)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The tpm_chip structure contains the list of PCR banks currently allocated
in the TPM. When support for crypto agility will be added to the TPM
driver, users of the driver have to provide a digest for each allocated
bank to tpm_pcr_extend(). With this patch, they can obtain the PCR bank
algorithms directly from chip->allocated_banks.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently, the TPM driver retrieves the digest size from a table mapping
TPM algorithms identifiers to identifiers defined by the crypto subsystem.
If the algorithm is not defined by the latter, the digest size can be
retrieved from the output of the PCR read command.
The patch modifies the definition of tpm_pcr_read() and tpm2_pcr_read() to
pass the desired hash algorithm and obtain the digest size at TPM startup.
Algorithms and corresponding digest sizes are stored in the new structure
tpm_bank_info, member of tpm_chip, so that the information can be used by
other kernel subsystems.
tpm_bank_info contains: the TPM algorithm identifier, necessary to generate
the event log as defined by Trusted Computing Group (TCG); the digest size,
to pad/truncate a digest calculated with a different algorithm; the crypto
subsystem identifier, to calculate the digest of event data.
This patch also protects against data corruption that could happen in the
bus, by checking that the digest size returned by the TPM during a PCR read
matches the size of the algorithm passed to tpm2_pcr_read().
For the initial PCR read, when digest sizes are not yet available, this
patch ensures that the amount of data copied from the output returned by
the TPM does not exceed the size of the array data are copied to.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Rename tpm2_* to tpm_* and move the definitions to include/linux/tpm.h so
that these can be used by other kernel subsystems (e.g. IMA).
Also, set the length of the digest array in tpm_digest to a new constant
named TPM_MAX_DIGEST_SIZE, equal to SHA512_DIGEST_SIZE.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This patch renames active_banks (member of tpm_chip) to allocated_banks,
stores the number of allocated PCR banks in nr_allocated_banks (new member
of tpm_chip), and replaces the static array with a pointer to a dynamically
allocated array.
tpm2_get_pcr_allocation() determines if a PCR bank is allocated by checking
the mask in the TPML_PCR_SELECTION structure returned by the TPM for
TPM2_Get_Capability(). If a bank is not allocated, the TPM returns that
bank in TPML_PCR_SELECTION, with all bits in the mask set to zero. In this
case, the bank is not included in chip->allocated_banks, to avoid that TPM
driver users unnecessarily calculate a digest for that bank.
One PCR bank with algorithm set to SHA1 is always allocated for TPM 1.x.
As a consequence of the introduction of nr_allocated_banks,
tpm_pcr_extend() does not check anymore if the algorithm stored in tpm_chip
is equal to zero.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Remove @flags from tpm_transmit() API. It is no longer used for
anything.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Call tpm_chip_start() and tpm_chip_stop() in
* tpm_chip_register()
* tpm_class_shutdown()
* tpm_del_char_device()
* tpm_pm_suspend()
* tpm_try_get_ops() and tpm_put_ops()
* tpm2_del_space()
And remove these calls from tpm_transmit(). The core reason for this
change is that in tpm_vtpm_proxy a locality change requires a virtual
TPM command (a command made up just for that driver).
The consequence of this is that this commit removes the remaining nested
calls.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Encapsulate power gating and locality functionality to tpm_chip_start()
and tpm_chip_stop() in order to clean up the branching mess in
tpm_transmit().
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Added locking as part of tpm_try_get_ops() and tpm_put_ops() as they are
anyway used in most of the call sites except in tpmrm_release() where we
take the locks manually.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Use tpm_try_get_ops() in tpm-sysfs.c so that we can consider moving
other decorations (locking, localities, power management for example)
inside it. This direction can be of course taken only after other call
sites for tpm_transmit() have been treated in the same way.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Remove @space from tpm_transmit() API` in order to completely remove the
bound between low-level transmission functionality and TPM spaces. The
only real dependency existing is the amount of data saved before trying
to send a command to the TPM.
It doesn't really matter if we save always a bit more than needed so
this commit changes the amount saved always to be the size of the TPM
header and three handles.
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Prepare and commit TPM space before and after calling tpm_transmit()
instead of doing that inside tpm_transmit(). After this change we can
remove TPM_TRANSMIT_NESTED flag from tpm2_prepare_space() and
tpm2_commit_space() and replace it with TPM_TRANSMIT_UNLOCKED.
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Move tpm_validate_command() to tpm2-space.c and make it part of the
tpm2_prepare_space() flow. Make cc resolution as part of the TPM space
functionality in order to detach it from rest of the tpm_transmit()
flow.
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Move locking, locality handling and power management to tpm_transmit()
in order to simplify the flow.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Encapsulate tpm_transmit() call pattern to tpm_dev_transmit() because it
is identically used from two places. Use unlocked version of
tpm_transmit() so that we are able to move the calls to
tpm2_prepare_space() and tpm2_commit_space() later on to this new
function.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Instead of accessing fields of the command header through offsets to
the raw buffer, it is a better idea to use the header struct pointer
that is already used elsewhere in the function.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Declare struct tpm_header that replaces struct tpm_input_header and
struct tpm_output_header.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
The error logging for tpm2_commit_space() is in a wrong place. This
commit moves it inside that function.
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Do not print partial list of PCRs when tpm1_pcr_read() fails but instead
return 0 from pcrs_show(). This is consistent behavior with other sysfs
functions.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Return zero when tpm_buf_init() fails as we do for other functions in
tpm-sysfs.c.
Fixes: da379f3c1d ("tpm: migrate pubek_show to struct tpm_buf")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Since we pass an initialized struct tpm_buf instance in every call site
now, it is cleaner to pass that directly to the tpm_transmit_cmd() as
the TPM command/response buffer.
Fine-tune a little bit tpm_transmit() and tpm_transmit_cmd() comments
while doing this.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Set tpm_chip->timeouts_adjusted directly in the update_timeouts
code instead of returning bool. In case of tpm read failing
print warning that the read failed and continue on.
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently tpm_transmit_cmd will print an error message if the tpm
returns something other than TPM2_RC_SUCCESS. This means that if the
tpm returns that it is testing an error message will be printed, and
this can cause confusion for the end user. So avoid printing the error
message if TPM2_RC_TESTING is the return code.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
TCG defines two structures, TCG_EfiSpecIDEventStruct and TCG_PCR_EVENT2,
which contain variable-sized arrays in the middle of the definition.
Since these structures are not suitable for type casting, this patch
removes structure members after the variable-sized arrays and adds the
_head suffix to the structure name, to indicate that the renamed structures
do not contain all fields defined by TCG.
Lastly, given that variable-sized arrays are now in the last position, and
given that the size of the arrays cannot be determined in advance, this
patch also sets the size of those arrays to zero and removes the definition
of TPM2_ACTIVE_PCR_BANKS.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
It is unable to read the entry when it is the only one in
binary_bios_measurements:
00000000 00 00 00 00 08 00 00 00 c4 2f ed ad 26 82 00 cb
00000010 1d 15 f9 78 41 c3 44 e7 9d ae 33 20 00 00 00 00
00000020
This is obviously a firmware problem on my linux machine:
Manufacturer: Inspur
Product Name: SA5212M4
Version: 01
However, binary_bios_measurements should return it any way,
rather than nothing, after all its content is completely
valid.
Fixes: 55a82ab318 ("tpm: add bios measurement log")
Signed-off-by: Jia Zhang <zhang.jia@linux.alibaba.com>
Reviewd-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The responsibility of tpm1_bios_measurements_start() is to walk over the
first *pos measurements, ensuring the skipped and to-be-read
measurements are not out-of-boundary.
This commit simplifies the loop by employing a do-while loop with
the necessary sanity check.
Signed-off-by: Jia Zhang <zhang.jia@linux.alibaba.com>
Reviewd-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Return -E2BIG when the transfer is incomplete. The upper layer does
not retry, so not doing that is incorrect behaviour.
Cc: stable@vger.kernel.org
Fixes: a2871c62e1 ("tpm: Add support for Atmel I2C TPMs")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
The send() callback should never return length as it does not in every
driver except tpm_crb in the success case. The reason is that the main
transmit functionality only cares about whether the transmit was
successful or not and ignores the count completely.
Suggested-by: Stefan Berger <stefanb@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Use guid_copy() instead of memcpy() to hide guid_t implementation details and
to show we expect guid_t in a raw buffer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Instead of magic number use pre-defined constant for UUID binary and
string representations.
While here, drop the implementation details of guid_t type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Also converted a "17" in the error string to UUID_SIZE + 1]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
devm_kasprintf() may return NULL if internal allocation failed so this
assignment is not safe. Moved the error exit path and added the !NULL
which then allows the devres manager to take care of cleanup.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: cd2315d471 ("ipmi: kcs_bmc: don't change device name")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
The user can ask the message to be returned even if it didn't supply
enough memory for the data, and it will return an error but still
fills in as much data as possible. However, the return value
wasn't being set to an error, it was being overwritten. Create a
second return value for that case.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Trivial fix to clean up an indentation issue, remove space
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The code to tell the lower layer to enable or disable watching for
certain things was lazy in disabling, it waited until a timer tick
to see if a disable was necessary. Not a really big deal, but it
could be improved.
Modify the code to enable and disable watching immediately and don't
do it from the background timer any more.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Kamlakant Patel <kamlakant.patel@cavium.com>
The IPMI driver has a mechanism to tell the lower layers it needs
to watch for messages, commands, and watchdogs (so it doesn't
needlessly poll). However, it needed some extensions, it needed
a way to tell what is being waited for so it could set the timeout
appropriately.
The update to the lower layer was also being done once a second
at best because it was done in the main timeout handler. However,
if a command is sent and a response message is coming back,
it needed to be started immediately. So modify the code to
update immediately if it needs to be enabled. Disable is still
lazy.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Commit 89986496de ("ipmi: Turn off all activity on an idle ipmi
interface") modified the IPMI code to only request events when the
driver had somethine waiting for events. The SSIF code, however,
was using the event fetch request to also fetch the flags.
Add a timer and the proper handling for the upper layer telling
whether flags fetches are required.
Reported-by: Kamlakant Patel <Kamlakant.Patel@cavium.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Kamlakant Patel <kamlakant.patel@cavium.com>
* Rename TPM_BUFSIZE defined in drivers/char/tpm/st33zp24/st33zp24.h to
ST33ZP24_BUFSIZE.
* Rename TPM_BUFSIZE defined in drivers/char/tpm/tpm_i2c_infineon.c to
TPM_I2C_INFINEON_BUFSIZE.
* Rename TPM_RETRY in tpm_i2c_nuvoton to TPM_I2C_RETRIES.
* Remove TPM_HEADER_SIZE from tpm_i2c_nuvoton.
Cc: stable@vger.kernel.org
Fixes: bf38b87108 ("tpm/tpm_i2c_stm_st33: Split tpm_i2c_tpm_st33 in 2 layers (core + phy)")
Fixes: aad628c1d9 ("char/tpm: Add new driver for Infineon I2C TIS TPM")
Fixes: 32d33b29ba ("TPM: Retry SaveState command in suspend path")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The current approach to read first 6 bytes from the response and then tail
of the response, can cause the 2nd memcpy_fromio() to do an unaligned read
(e.g. read 32-bit word from address aligned to a 16-bits), depending on how
memcpy_fromio() is implemented. If this happens, the read will fail and the
memory controller will fill the read with 1's.
This was triggered by 170d13ca3a, which should be probably refined to
check and react to the address alignment. Before that commit, on x86
memcpy_fromio() turned out to be memcpy(). By a luck GCC has done the right
thing (from tpm_crb's perspective) for us so far, but we should not rely on
that. Thus, it makes sense to fix this also in tpm_crb, not least because
the fix can be then backported to stable kernels and make them more robust
when compiled in differing environments.
Cc: stable@vger.kernel.org
Cc: James Morris <jmorris@namei.org>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
On ARM SoC's with TrustZone enabled, peripherals like entropy sources
might not be accessible to normal world (linux in this case) and rather
accessible to secure world (OP-TEE in this case) only. So this driver
aims to provides a generic interface to OP-TEE based random number
generator service.
This driver registers on TEE bus to interact with OP-TEE based rng
device/service.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Here are some small char and misc driver fixes to resolve some reported
issues, as well as a number of binderfs fixups that were found after
auditing the filesystem code by Al Viro. As binderfs hasn't been in a
previous release yet, it's good to get these in now before the first
users show up.
All of these have been in linux-next for a bit with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXEr/Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymLqACgsYcCs0r/RMqXfvMqJ7beUGq02ioAoNPD0hQh
Z76nfI+21TiuXx24JCfZ
=Fo1U
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes to resolve some
reported issues, as well as a number of binderfs fixups that were
found after auditing the filesystem code by Al Viro. As binderfs
hasn't been in a previous release yet, it's good to get these in now
before the first users show up.
All of these have been in linux-next for a bit with no reported
issues"
* tag 'char-misc-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (26 commits)
i3c: master: Fix an error checking typo in 'cdns_i3c_master_probe()'
binderfs: switch from d_add() to d_instantiate()
binderfs: drop lock in binderfs_binder_ctl_create
binderfs: kill_litter_super() before cleanup
binderfs: rework binderfs_binder_device_create()
binderfs: rework binderfs_fill_super()
binderfs: prevent renaming the control dentry
binderfs: remove outdated comment
binderfs: use __u32 for device numbers
binderfs: use correct include guards in header
misc: pvpanic: fix warning implicit declaration
char/mwave: fix potential Spectre v1 vulnerability
misc: ibmvsm: Fix potential NULL pointer dereference
binderfs: fix error return code in binderfs_fill_super()
mei: me: add denverton innovation engine device IDs
mei: me: mark LBG devices as having dma support
mei: dma: silent the reject message
binderfs: handle !CONFIG_IPC_NS builds
binderfs: reserve devices for initial mount
binderfs: rename header to binderfs.h
...
The virtio-rng driver uses a completion called have_data to wait for a
virtio read to be fulfilled by the hypervisor. The completion is reset
before placing a buffer on the virtio queue and completed by the virtio
callback once data has been written into the buffer.
Prior to this commit, the driver called init_completion on this
completion both during probe as well as when registering virtio buffers
as part of a hwrng read operation. The second of these init_completion
calls should instead be reinit_completion because the have_data
completion has already been inited by probe. As described in
Documentation/scheduler/completion.txt, "Calling init_completion() twice
on the same completion object is most likely a bug".
This bug was present in the initial implementation of virtio-rng in
f7f510ec19 ("virtio: An entropy device, as suggested by hpa"). Back
then the have_data completion was a single static completion rather than
a member of one of potentially multiple virtrng_info structs as
implemented later by 08e53fbdb8 ("virtio-rng: support multiple
virtio-rng devices"). The original driver incorrectly used
init_completion rather than INIT_COMPLETION to reset have_data during
read.
Tested by running `head -c48 /dev/random | hexdump` within crosvm, the
Chrome OS virtual machine monitor, and confirming that the virtio-rng
driver successfully produces random bytes from the host.
Signed-off-by: David Tolnay <dtolnay@gmail.com>
Tested-by: David Tolnay <dtolnay@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The IPMI driver was recently modified to use SRCU, but it turns out
this uses a chunk of percpu memory, even if IPMI is never used.
So modify thing to on initialize on the first use. There was already
code to sort of handle this for handling init races, so piggy back
on top of that, and simplify it in the process.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reported-by: Tejun Heo <tj@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.18
Some IPMI modules (e.g. ibmpex_msg_handler()) will have ipmi_usr_hdlr
handlers that call ipmi_free_recv_msg() directly. This will essentially
kfree(msg), leading to use-after-free.
This does not happen in the ipmi_devintf module, which will queue the
message and run ipmi_free_recv_msg() later.
BUG: KASAN: use-after-free in deliver_response+0x12f/0x1b0
Read of size 8 at addr ffff888a7bf20018 by task ksoftirqd/3/27
CPU: 3 PID: 27 Comm: ksoftirqd/3 Tainted: G O 4.19.11-amd64-ani99-debug #12.0.1.601133+pv
Hardware name: AppNeta r1000/X11SPW-TF, BIOS 2.1a-AP 09/17/2018
Call Trace:
dump_stack+0x92/0xeb
print_address_description+0x73/0x290
kasan_report+0x258/0x380
deliver_response+0x12f/0x1b0
? ipmi_free_recv_msg+0x50/0x50
deliver_local_response+0xe/0x50
handle_one_recv_msg+0x37a/0x21d0
handle_new_recv_msgs+0x1ce/0x440
...
Allocated by task 9885:
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc_trace+0x116/0x290
ipmi_alloc_recv_msg+0x28/0x70
i_ipmi_request+0xb4a/0x1640
ipmi_request_settime+0x1b8/0x1e0
...
Freed by task 27:
__kasan_slab_free+0x12e/0x180
kfree+0xe9/0x280
deliver_response+0x122/0x1b0
deliver_local_response+0xe/0x50
handle_one_recv_msg+0x37a/0x21d0
handle_new_recv_msgs+0x1ce/0x440
tasklet_action_common.isra.19+0xc4/0x250
__do_softirq+0x11f/0x51f
Fixes: e86ee2d44b ("ipmi: Rework locking and shutdown for hot remove")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Fred Klassen <fklassen@appneta.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
channel and addr->channel are indirectly controlled by user-space,
hence leading to a potential exploitation of the Spectre variant 1
vulnerability.
These issues were detected with the help of Smatch:
drivers/char/ipmi/ipmi_msghandler.c:1381 ipmi_set_my_address() warn: potential spectre issue 'user->intf->addrinfo' [w] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:1401 ipmi_get_my_address() warn: potential spectre issue 'user->intf->addrinfo' [r] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:1421 ipmi_set_my_LUN() warn: potential spectre issue 'user->intf->addrinfo' [w] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:1441 ipmi_get_my_LUN() warn: potential spectre issue 'user->intf->addrinfo' [r] (local cap)
drivers/char/ipmi/ipmi_msghandler.c:2260 check_addr() warn: potential spectre issue 'intf->addrinfo' [r] (local cap)
Fix this by sanitizing channel and addr->channel before using them to
index user->intf->addrinfo and intf->addrinfo, correspondingly.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The block number was not being compared right, it was off by one
when checking the response.
Some statistics wouldn't be incremented properly in some cases.
Check to see if that middle-part messages always have 31 bytes of
data.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 4.4
Without ".owner = THIS_MODULE" it is possible to crash the kernel
by unloading the mbcs module while someone works with the file.
Fix this by initializing the ‘struct file_operations' ->owner with
THIS_MODULE.
Signed-off-by: Naveen Kumar Parna <parna.naveenkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IndexCard is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/char/applicom.c:418 ac_write() warn: potential spectre issue 'apbs' [r]
drivers/char/applicom.c:728 ac_ioctl() warn: potential spectre issue 'apbs' [r] (local cap)
Fix this by sanitizing IndexCard before using it to index apbs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
