DWC3 controller on Exynos SoC series have separate control for
suspend clock which replaces pipe3_rx_pclk as clock source to
a small part of DWC3 core that operates when SS PHY is in its
lowest power state (P3) in states SS.disabled and U3.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no need to keep one local variable for clock, and
then assign the same to 'clk' member of dwc3_exynos.
Just cleaning it up.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was another instance where we were
holding pointers which could be long gone.
Fix that by caching only values pointed to
by such pointer.
Because no crash has been observed, this patch
will be sent on v3.19 merge window, instead of
-rc.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for AMD Nolan (NL) FPGA and SoC platform.
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is recommended to set USB3 and USB2 SUSPHY bits to '1' after the core
initialization is completed above the dwc3 revision 1.94a.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It enables hibernation if the function is set in coreConsultant.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget/function drivers might want to do
improper request recycling by allocating a single
request from one particular endpoint and queueing
it to another completely unrelated endpoint.
One such case was found with f_loopback.c.
To prevent such cases from happening again, let's
WARN() so we get a loud enough failure and persuade
users to report errors.
Signed-off-by: Felipe Balbi <balbi@ti.com>
whenever we get a Disconnect Interrupt, we should
make sure to update out udc state to NOT_ATTACHED,
otherwise sysfs will show wrong values.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enabling the core interrupts in complete is too late for
XHCI, and stops it from proper operation. The root of the
problem is due to a disagreement between dwc3-omap and XHCI
about when IRQs should be enabled.
As it turns out, ->resume's documentation states that:
"... generally the driver is expected to start working
again, responding to hardware events and software requests
(the device itself may be left in a low-power state, waiting
for a runtime resume to occur) ..."
From that we infer that IRQs must be unmasked by the end of
->resume().
Due to that, we will remove ->prepare() and ->complete() and
disable/enable interrupts in ->suspend()/->resume().
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the probe drivers have already set the dma_mask, not
replacing the value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3's GUID register is supposed to be used to write
any sort of version we might want. It helps when getting
bug reports for platforms you don't have HW to know
which kernel version of the driver was running on the
platform.
Because we don't really track driver version, but we _do_
track the kernel version, let's write LINUX_VERSION_CODE to
that register and use it for debugging.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 02dae36aa6.
That commit is bogus in two ways:
1) There's no way dwc3-omap's ->suspend() can cause any effect
on xhci's ->suspend(). Linux device driver model guarantees
that a parent's ->suspend() will only be called after all
children are suspended. dwc3-omap is the parent of the
parent of xhci.
2) When implementing Deep Sleep states where context is lost,
USBOTGSS_IRQ0 register, well, looses context so we
_must_ rewrite it otherwise core IRQs will never be
reenabled and USB will appear to be dead.
Fixes: 02dae36 (usb: dwc3: dwc3-omap: Disable/Enable only
wrapper interrupts in prepare/complete)
Cc: <stable@vger.kernel.org> # v3.17
Cc: George Cherian <george.cherian@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to Section 8.5.3.2 of the USB 2.0 specification,
a USB device must terminate a Data Phase with either a
short packet or a ZLP (if the previous transfer was
a multiple of wMaxPacketSize).
For reference, here's what the USB 2.0 specification, section
8.5.3.2 says:
"
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase
in which the host requests more data than is contained
in the specified data structure. When all of the data
structure is returned to the host, the function should
indicate that the Data stage is ended by returning a
packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of
wMaxPacketSize for the pipe, the function will return
a zero-length packet to indicate the end of the Data
stage.
"
Signed-off-by: Felipe Balbi <balbi@ti.com>
if our list of requests is empty, return early.
There's really nothing to be done in case our
request list is empty anyway because the only
situation where we our list is empty, is when
we're transferring ZLPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The device controller is the same but it has different PCI ID. Add this new
ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).
Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.
This patch should be backported to all kernels since v3.2.
Cc: <stable@vger.kernel.org> # v3.2+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of releasing the lock and calling locked
versions of our set_halt() methods, let's hold
the lock all the way through and call unlocked
versions of those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__dwc3_gadget_ep_set_halt() is the function which
handles the actual halt feature. In order to cope
with some extra cleanup comming as a follow-up patch
let's move the isochronous endpoint check there too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep0_set_halt() will be called without
locks held in some cases, so we must hold the lock
on our own. While at that, also add a version without
locks to be called in certain conditions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
