Move out the format related helper functions from vfe and video in a
separate file. The goal here is to create a format API.
Signed-off-by: Radoslav Tsvetkov <quic_rtsvetko@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Following the example of VFE and CSID, attach the CSIPHY
formats to the subdevices resources.
Signed-off-by: Radoslav Tsvetkov <quic_rtsvetko@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # sc8280xp/sm8250/sdm845/apq8016
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Following the example of VFE, move all formats of the decoder
to camss-csid.c and attach them to the subdevices resources.
Signed-off-by: Radoslav Tsvetkov <quic_rtsvetko@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # sc8280xp/sm8250/sdm845/apq8016
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Video node formats have direct dependency by the sub-device pad formats.
Remove dependency for SoC version and move format definitions in device
which creates video node.
This commit attaches a struct to the VFE resources that holds format
description, so it is much easier to assign them to the video node.
No need to use a switch-case.
NOTE: The mbus_bpp is used to calculate the clock rates and is different
from bpp which is the bits per pixel written to memory. We need to keep
both values to not break the calcualtions.
Signed-off-by: Radoslav Tsvetkov <quic_rtsvetko@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently resources structure grows with additional parameters required for
each sub-deivce. However each sub-device has some specific resources or
configurations which need to be passed during the initialization.
This change adds per sub-device type structure to simplify the things
and removes the magical void pointer to hw_ops.
Signed-off-by: Radoslav Tsvetkov <quic_rtsvetko@quicinc.com>
Signed-off-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # sc8280xp/sm8250/sdm845/apq8016
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Modify section "Video and Sliced VBI Looping" in Documentation to explain
the vivid loopback support for video across multiple vivid instances.
Previous documentation is out-of-date as it was explaining looping in a
single vivid instance only.
Also, in "Some Future Improvements" the item "Add support to loop
from a specific output to a specific input across vivid instances"
can be dropped since that's now implemented.
Signed-off-by: Dorcas Anono Litunya <anonolitunya@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Instead of using hardwired video loopback limited to a single vivid
instance, use the new 'Connected To' controls to only loopback if an
HDMI or S-Video input is connected to another output, which can be
in another vivid instance. Effectively this emulates connecting and
disconnecting an HDMI/S-Video cable.
The Loop Video control is dropped since it has now been replaced by
the new 'Connected To' controls. The Display Present has also been
dropped since it no longer fits.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Co-developed-by: Dorcas Anono Litunya <anonolitunya@gmail.com>
Signed-off-by: Dorcas Anono Litunya <anonolitunya@gmail.com>
The video loopback functionality in vivid is very crude. What we really
want is to be able to emulate connecting an HDMI or S-Video input to
an HDMI or S-Video output, and the input and output can be in different
vivid instances.
Effectively this emulates what happens when you physically connect an
HDMI or S-Video cable between two devices.
In particular, this makes prototyping with vivid much more realistic.
This patch creates a menu control for each HDMI or S-Video input. The
menu control starts with "Test Pattern Generator" and "None" (i.e.
disconnected). After that up to 62 HDMI or S-Video outputs are listed
that you can connect the input to.
If there are more than 62 HDMI or S-Video outputs, then those will not
be included in the menu (currently menucontrols have max 64 entries).
If an input is connected to an output, then all other 'Connected To'
controls are updated to exclude that output to avoid having multiple
inputs connected to the same output.
Signed-off-by: Dorcas Anono Litunya <anonolitunya@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: use u8 in loops in vivid_create_controls() to avoid truncate warning]
Add the instance number before the input or output number.
So "HDMI 1" becomes "HDMI 000-1".
This is helps identifying which input or output belongs to
which vivid instance.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When setting the EDID it would attempt to update two controls
that are only present if there is an HDMI output configured.
If there isn't any (e.g. when the vivid module is loaded with
node_types=1), then calling VIDIOC_S_EDID would crash.
Fix this by first checking if outputs are present.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Returning an EDID for a connected output would modify the original
input EDID with the physical address of the output. That causes
problems, and it should just update the physical address of the
output EDID.
Update vivid_hdmi_edid to set the physical address to 0.0.0.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Modifying documentation to remove 'Capture Overlay section' as
destructive capture overlay support was removed.
See commit ccaa9d50ca ("media: vivid: drop overlay support")
Signed-off-by: Dorcas Anono Litunya <anonolitunya@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop the "Video, VBI and RDS Looping" section, instead moving the
Video/VBI info to section "Video and Sliced VBI looping" and the
RDS info to section "Radio & RDS Looping".
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The documentation contained several instances of "section X"
references, which no longer map to whatever X was.
Replace these by the section titles.
Also fix a single confusing typo in the "Radio & RDS Looping" section:
"are regular frequency intervals" -> "at regular frequency intervals"
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
To support sources that implement the .enable_streams() and
.disable_streams() operations, replace the manual calls to the subdev
.s_stream() operation with the v4l2_subdev_enable_streams() and
v4l2_subdev_disable_streams() helpers. The helpers fall back to
.s_stream() if the source doesn't implement the new operations, so
backward compatibility is preserved.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use CCI_REG16_LE macro in order to access little-endian
encoded registers of the P3 (CSI) section.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Correct error handling within the dcmipp_create_subdevs by properly
decrementing the i counter when releasing the subdeves.
Fixes: 28e0f37722 ("media: stm32-dcmipp: STM32 DCMIPP camera interface driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add documentation for the PiSP Back End memory-to-memory ISP.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add support for the Raspberry Pi PiSP Back End.
The driver has been upported from the Raspberry Pi kernel at revision
f74893f8a0c2 ("drivers: media: pisp_be: Update seqeuence numbers of the
buffers").
The ISP documentation is available at:
https://datasheets.raspberrypi.com/camera/raspberry-pi-image-signal-processor-specification.pdf
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.org>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: drop dev_err after platform_get_irq to fix a coccinelle check]
Add bindings for the Raspberry Pi PiSP Back End memory-to-memory image
signal processor.
Datasheet:
https://datasheets.raspberrypi.com/camera/raspberry-pi-image-signal-processor-specification.pdf
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add Raspberry Pi compressed RAW Bayer formats.
The compression algorithm description is provided by Nick Hollinghurst
<nick.hollinghurst@raspberrypi.com> from Raspberry Pi.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add format description for the PiSP Back End configuration parameter
buffer.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add the Raspberry Pi PiSP Back End uAPI header.
The header defines the data type used to configure the PiSP Back End
ISP.
The detailed description of the types and of the ISP configuration
procedure is available at
https://datasheets.raspberrypi.com/camera/raspberry-pi-image-signal-processor-specification.pdf
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Y10P, Y12P and Y14P format variants are packed according to
the RAW10, RAW12 and RAW14 formats as defined by the MIPI CSI-2
specification. Document it.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
While queue_setup was correct for CREATE_BUFS support for
video devices, for VBI, SDR and touch devices it was wrong.
This was found after adding new v4l2-compliance tests.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In several places a division by fmt->vdownsampling[p] was
missing in the sizeimage[p] calculation, causing incorrect
behavior for multiplanar formats were some planes are smaller
than the first plane.
Found by new v4l2-compliance tests.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Store the active formats and crop rectangle in the subdevice active
state. This simplifies implementation of the format and selection
accessors, and allows using the v4l2_subdev_get_fmt() helper to
implement the .get_fmt() operation.
The active configuration that is used in the .process_frame() handler is
still stored in the vimc_scaler_device structure. The driver could
instead access the active state in the .process_frame() handler, but the
required locking could interfere with the real time constraints of the
frame processing. This data would be stored in registers in the
.s_stream() handler for real hardware, storing it in dedicated storage
thus mimics a real driver. To differentiate them from the rest of the
device private data, move the corresponding fields to a sub-structure of
vimc_scaler_device named hw.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Store the active formats and crop rectangle in the subdevice active
state. This simplifies implementation of the format and selection
accessors, and allows using the v4l2_subdev_get_fmt() helper to
implement the .get_fmt() operation.
The active configuration that is used in the .process_frame() handler is
still stored in the vimc_debayer_device structure. The driver could
instead access the active state in the .process_frame() handler, but the
required locking could interfere with the real time constraints of the
frame processing. This data would be stored in registers in the
.s_stream() handler for real hardware, storing it in dedicated storage
thus mimics a real driver. To differentiate them from the rest of the
device private data, move the corresponding fields to a sub-structure of
vimc_debayer_device named hw.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Store the active formats and crop rectangle in the subdevice active
state. This simplifies implementation of the format and selection
accessors, and allows using the v4l2_subdev_get_fmt() helper to
implement the .get_fmt() operation.
The active configuration that is used in the .process_frame() handler is
still stored in the vimc_sensor_device structure. The driver could
instead access the active state in the .process_frame() handler, but the
required locking could interfere with the real time constraints of the
frame processing. This data would be stored in registers in the
.s_stream() handler for real hardware, storing it in dedicated storage
thus mimics a real driver. To differentiate them from the rest of the
device private data, move the corresponding fields to a sub-structure of
vimc_sensor_device named hw.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Finalize subdev initialization for all subdevs that provide a
.init_state() operation. This creates an active state for all those
subdevs, which subsequent patches will use to simplify the
implementation of individual vimc entities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Initialize the subdev internal_ops field in the vimc_ent_sd_register()
function. This handles the internal ops the same way as the subdev ops,
and prepares for moving to the V4L2 subdev active state API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The vic_sca_pad enum's name has been shortened to the extreme for no
good reason. Rename it to vimc_scaler_pad.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The ent_config array contains data that is never modified. Make it
const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The vimc_ent_type structure contains static pointers to functions, and
no other information that need to be modified after initialization. Make
them const to avoid the risk of arbitrary code execution following an
overflow that would overwrite the structure's contents.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The .init_state() operations of the debayer and sensor entities iterate
over the entity's pads. In practice, the iteration covers a single pad
only. Access the pad directly and remove the loops.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
- Cleanups and fixes for the Renesas R-Car VSP and VIN drivers
- Miscellaneous cleanups to V4L2 core
-----BEGIN PGP SIGNATURE-----
iJgEABYKAEAWIQTAnvhxs4J7QT+XHKnMPy2AAyfeZAUCZnNeLCIcbGF1cmVudC5w
aW5jaGFydEBpZGVhc29uYm9hcmQuY29tAAoJEMw/LYADJ95kxyUBAKdQ86lXbVd1
97wtbRDP3H3MTtEowjskDGqhfH0QA9kXAP9eTf7rJixORvXFg/DaLcjdWIyfIsjY
4gz7aHO8MsXGBg==
=BgVa
-----END PGP SIGNATURE-----
Merge tag 'tags/next-media-renesas-20240619' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux.git
- Conversion of max9286 and adv748x to V4L2 subdev active state
- Cleanups and fixes for the Renesas R-Car VSP and VIN drivers
- Miscellaneous cleanups to V4L2 core
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Replace the incorrect reference to the v4l2_subdev_enable_stream()
function with the correct v4l2_subdev_enable_streams() spelling.
Fixes: d0749adb30 ("media: v4l2-subdev: Add subdev .(enable|disable)_streams() operations")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20240619225343.15873-1-laurent.pinchart@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
FW_LOADER config only selects the firmware loader API, but we also need
the sysfs_upload symbols for firmware_upload_unregister() and
firmware_upload_register() to function properly.
Fixes: 7a52ab415b ("media: i2c: Add driver for THine THP7312")
Cc: stable@vger.kernel.org
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Link: https://lore.kernel.org/r/20240620102544.1918105-1-kory.maincent@bootlin.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The email address bounced. I couldn't find a newer one in recent git
history, so update MAINTAINERS accordingly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix flags in X1 Yoga example. MEDIA_LNK_FL_DYNAMIC (0x4 in the link flag)
was removed in V4 Intel IPU6 and IPU6 input system drivers. Added -V flag
to media-ctl commands for X1 Yoga, lower-case v only makes it verbose
upper-case V sets the format.
Signed-off-by: Samuel Wein <sam@samwein.com>
[Sakari Ailus: Align subject line, rewrap commit message.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a V4L2 sub-device driver for Galaxycore GC05A2 image sensor.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
[Sakari Ailus: Fold in MAINTAINERS change.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add YAML device tree binding for GC05A2 CMOS image sensor,
and the relevant MAINTAINERS entries.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a V4L2 sub-device driver for Galaxycore GC08A3 image sensor.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
[Sakari Ailus: Fold in MAINTAINERS change.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
