Like switchdev attr get/set, add new switchdev obj add/del. switchdev objs
will be things like VLANs or FIB entries, so add/del fits better for
objects than get/set used for attributes.
Use same two-phase prepare-commit transaction model as in attr set.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP update is just a settable port attribute, so convert
switchdev_port_stp_update to an attr set.
For DSA, the prepare phase is skipped and STP updates are only done in the
commit phase. This is because currently the DSA drivers don't need to
allocate any memory for STP updates and the STP update will not fail to HW
(unless something horrible goes wrong on the MDIO bus, in which case the
prepare phase wouldn't have been able to predict anyway).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch ID is just a gettable port attribute. Convert switchdev op
switchdev_parent_id_get to a switchdev attr.
Note: for sysfs and netlink interfaces, SWITCHDEV_ATTR_PORT_PARENT_ID is
called with SWITCHDEV_F_NO_RECUSE to limit switch ID user-visiblity to only
port netdevs. So when a port is stacked under bond/bridge, the user can
only query switch id via the switch ports, but not via the upper devices
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new swdev ops for get/set switch port attributes. Most swdev
interactions on a port are gets or sets on port attributes, so rather than
adding ops for each attribute, let's define clean get/set ops for all
attributes, and then we can have clear, consistent rules on how attributes
propagate on stacked devs.
Add the basic algorithms for get/set attr ops. Use the same recusive algo
to walk lower devs we've used for STP updates, for example. For get,
compare attr value for each lower dev and only return success if attr
values match across all lower devs. For sets, set the same attr value for
all lower devs. We'll use a two-phase prepare-commit transaction model for
sets. In the first phase, the driver(s) are asked if attr set is OK. If
all OK, the commit attr set in second phase. A driver would NACK the
prepare phase if it can't set the attr due to lack of resources or support,
within it's control. RTNL lock must be held across both phases because
we'll recurse all lower devs first in prepare phase, and then recurse all
lower devs again in commit phase. If any lower dev fails the prepare
phase, we need to abort the transaction for all lower devs.
If lower dev recusion isn't desired, allow a flag SWITCHDEV_F_NO_RECURSE to
indicate get/set only work on port (lowest) device.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make it same as the netdev_switch_port_bridge_setlink/dellink
api (ie traverse lowerdevs to get to the switch port).
removes "WARN_ON(!ops->ndo_switch_parent_id_get)" because
direct bridge ports can be stacked netdevices (like bonds
and team of switch ports) which may not implement this ndo.
v2 to v3:
- remove changes to bond and team. Bring back the
transparently following lowerdevs like i initially
had for setlink/getlink
(http://www.spinics.net/lists/netdev/msg313436.html)
dave and scott feldman also seem to prefer it be that
way and move to non-transparent way of doing things
if we see a problem down the lane.
v3 to v4:
- fix ret initialization
v4 to v5:
- return err on first failure (scott feldman)
v5 to v6:
- change variable name (err) and initialize to
-EOPNOTSUPP (scott feldman).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move swdev wrappers over to new swdev ops (from previous ndo ops). No
functional changes to the implementation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
rocker: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
dsa: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the netlink flags (NLM_F_*) into switchdev driver for IPv4 FIB add op
to allow driver to 1) optimize hardware updates, 2) handle ip route prepend
and append commands correctly.
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call into the switchdev driver any time an IPv4 fib entry is
added/modified/deleted from the kernel's FIB. The switchdev driver may or
may not install the route to the offload device. In the case where the
driver tries to install the route and something goes wrong (device's routing
table is full, etc), then all of the offloaded routes will be flushed from the
device, route forwarding falls back to the kernel, and no more routes are
offloading.
We can refine this logic later. For now, use the simplist model of offloading
routes up to the point of failure, and then on failure, undo everything and
mark IPv4 offloading disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flesh out ndo wrappers to call into device driver. To call into device driver,
the wrapper must interate over route's nexthops to ensure all nexthop devs
belong to the same switch device. Currently, there is no support for route's
nexthops spanning offloaded and non-offloaded devices, or spanning ports of
multiple offload devices.
Since switch device ports may be stacked under virtual interfaces (bonds and/or
bridges), and the route's nexthop may be on the virtual interface, the wrapper
will traverse the nexthop dev down to the base dev. It's the base dev that's
passed to the switchdev driver's ndo ops.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep switchdev FIB offload model simple for now and don't allow custom ip
rules.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 fib ndo wrapper funcs and stub them out for now.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
This patch adds two new api's netdev_switch_port_bridge_setlink
and netdev_switch_port_bridge_dellink to offload bridge port attributes
to switch port
(The names of the apis look odd with 'switch_port_bridge',
but am more inclined to change the prefix of the api to something else.
Will take any suggestions).
The api's look at the NETIF_F_HW_SWITCH_OFFLOAD feature flag to
pass bridge port attributes to the port device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces new notifier for purposes of exposing events which happen
on switch driver side. The consumers of the event messages are mainly involved
masters, namely bridge and ovs.
Suggested-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
To notify switch driver of change in STP state of bridge port, add new
.ndo op and provide switchdev wrapper func to call ndo op. Use it in bridge
code then.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.
Note that user can use random port netdevice to access the switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
