cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable omap_hsmmc for Keystone 2 architecture which reuses the HSMMC
IP found on OMAP platforms.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ACPI HIDs for Intel host controllers including one
supporting HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add some macros for HCON register operations
to make code more readable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC doesn't have a standard power control register, so when
writing this register in stack we should do nothing to avoid
incorrect operation.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This algorithm will try 1 degree increments, since there's no way to tell
what resolution the underlying phase code uses. As an added bonus, doing
many tunings yields better results since some tests are run more than once
(ex: if the underlying driver uses 45 degree increments, the tuning code
will try the same angle more than once).
It will then construct a list of good phase ranges (even ranges that cross
360/0), will pick the biggest range then it will set the sample_clk to the
middle of that range.
We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time (ex 10
degrees) this will not work with the current clock phase framework (which
floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.
If a device has device specific code (like exynos) then that will still
take precedence, otherwise this new code will execute. If the device wants
to tune, but has no sample_clk defined we'll return EIO with an error
message.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've introduced a new helper in the MMC core:
mmc_regulator_set_vqmmc(). Let's use this in dw_mmc. Using this new
helper has some advantages:
1. We get the mmc_regulator_set_vqmmc() behavior of trying to match
VQMMC and VMMC when the signal voltage is 3.3V. This ensures max
compatibility.
2. We get rid of a few more warnings when probing unsupported
voltages.
3. We get rid of some non-dw_mmc specific code in dw_mmc.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Freescale eSDHC driver now supports both little-endian and
big-endian mode eSDHC IPs for ARM and PPC. So, MMC_SDHCI_OF_ESDHC
option needs to be reconfigured.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add another PCI ID for an Intel eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci-pci-core.c:447:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.
- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to hardware spec, validate DDR50 mode
for SDXC.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD19 tuning is also available for DDR50 mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some sdio wifi modules have not been working reliable with the sunxi-mmc
host code. This turns out to be caused by starting new io-rw commands while
the card signals that it is still busy processing a previous command.
This commit adds card-busy detection to the sunxi-mmc driver which together
with recent core changes to check card-busy before starting io-rw commands
fixes the wifi reliability issues on the Cubietruck and other sunxi boards
using sdio wifi.
Reported-by: Eugene K <sigintmailru@gmail.com>
Suggested-by: Eugene K <sigintmailru@gmail.com>
Cc: Eugene K <sigintmailru@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_CAP_RUNTIME_RESUME support to save resume time
Drop unnecessary SDC_ARG write
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The goto is correct and the unreachable "return -EINVAL" should be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_init() will clear all irqs and set the needed irqs. So
logically sdhci_init() should be called before request irq.
If not, some irqs may be triggled and handled wrongly. Take
the following into consideration, after request irq, if
SDIO card interrupt enabled, a sd card in the sd slot will
trigger a mass of interrupt(SDHCI_INT_CARD_INT), because at
this time, the vmmc-regulator still not restore, no voltage
supply for the sd card, so the pin of data0~data3 change and
keep low, interrupt(SDHCI_INT_CARD_INT) will rise up ceaselessly.
Due to we already reguest irq, system will be busy in handling
this endless irq, can't response to other event.
So we should call sdhci_init() before request irq in sd resume.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver prints if the data width is 8-bit but it's using a
binary OR instead of a binary AND so it will always report as
"is_8bit=Y" regardless of the flags in host->mmc->caps.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry to the sdhci_acpi_uids list to detect the SD card
reader on the Asus X205Ta laptop.
dstd table:
Device (SDHC)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "PNP0FFF") // _HID: Hardware ID
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SD Card Controller - 80860F16") // _DDN: DOS Dev
Name (_UID, 0x03) // _UID: Unique ID
Name (RDEP, Package (0x02)
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs the
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk. Without it, the
internal clock could never stabilised when changing the sd clock
frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock
Control Register to 0 before computing the new value and writing it.
It disables the internal clock which causes a reset mecanism. If we
write the new value before this reset mecanism is done, it will prevent
the stabilisation of the internal clock, so a delay is needed. This
delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is
used.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of armada_38x_quirks error, all clocks should be cleaned-up, same
as after mv_conf_mbus_windows failure.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to 'FE-2946959' erratum the clock inversion option is
needed to support slow frequencies when the card input hold time
requirement is high. This setting is not required for high speed
MMC and might cause timing violation.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
shci-pxav3 driver is enabling by default the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not
required for Armada 38x and leads to wrong clock setting in the divider.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Starting with commit 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc") MMC on omap3 stopped working
for legacy booting.
This is because legacy booting sets up some of the resource in the
platform init code, and for optional regulators always seem to
return -EPROBE_DEFER for the legacy booting.
Let's fix the issue by checking for device tree based booting for
now. Then when omap3 boots in device tree only mode, this patch
can be just reverted.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c55d7a0553.
Without reverting this commit we get "unbalanced disables for pbias_mmc_omap4"
errors on omap4430. It seems that 4430 and 4460 behave in a different way for
the PBIAS regulator registers and until that has been debugged further we
cannot rely on the regulator status registers in hardare on 4430.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move pxamci to mmc slot-gpio API to fix interrupt request.
It fixes the case where the card detection is on a gpio expander, on I2C
for example on zylonite board. In this case, the card detect netsted
interrupt is called from a threaded interrupt. The request_irq() fails,
because a hard irq cannot be a nested interrupt from a threaded
interrupt (set __setup_irq()).
This was tested on zylonite and mioa701 boards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that support for platforms which have optional regulator is added,
remove CONFIG_REGULATOR check in omap_hsmmc.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
vdd voltage is set in mmc core to ios->vdd and vmmc should actually
be set to this voltage. Modify omap_hsmmc_enable_supply
to not take vdd as argument since now it's directly set to
the voltage in ios->vdd.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use regulator_is_enabled of pbias regulator to find pbias regulator
status instead of maintaining a custom bookkeeping
pbias_enabled variable.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enable vmmc_aux regulator only if it is in disabled state and disable
vmmc_aux regulator only if it is in enabled state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the regulator is enabled on boot (checked using regulator_is_enabled),
invoke regulator_enable() so that the usecount reflects the correct
state of the regulator and then disable the regulator so that the
initial state of the regulator is disabled. Avoid using ->set_power,
since set_power also takes care of setting the voltages which is not
needed at this point.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix omap_hsmmc_set_power so that pbias regulator is not enabled
during power off.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions to set pbias and invoke it from omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions for enable/disable supply and invoke it from
omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
