The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out.
Note it has no sdcard slot and therefore can only be fel booted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a dtsi file for A31s based boards.
Since the A31s is the same die as the A31 in a different package, this dtsi
simply includes sun6i-a31.dtsi and then overrides the pinctrl compatible to
reflect the different package, everything else is identical.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 has an ir receiver, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the ir receiver found on the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added a node label]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an ir_clk sub-node to the prcm node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Only SPI0 is enabled, as the schematic denotes it as the only SPI bus,
while other pins are reserved for different peripherals.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are based on the available SPI configurations of Cubieboard,
Olimex LIME, and PcDuino. There is no pin group for SPI3, as all the
boards seem to use those pins for EMAC.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Hummingbird A31 board, the RTL8211E ethernet phy has its reset
line connect to a gpio pin, instead of floating like on other boards.
Add the stmmac properties for describing the reset gpio.
The reset delays were taken from the RTL8211E datasheet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pinmux settings for the ir receive pin of the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.
Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Ippo q8h has its serial console connected to the r-uart. Adjust the
serial0 alias to match.
This fixes the kernel serial console no longer working since 3.19-rc1, because
8250_dw.c now honors dt aliases, causing the serial console to be ttyS5 rather
then being ttyS0, as it was in 3.18 and before.
Note that adjusting bootargs instead is not an acceptable fix, because
console=ttyS0,115200 is used by a lot of bootscripts, etc. and this should
continue to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
usbphy0 support in the sunxi usb-phy driver has been merged, but the
dtsi's for sun4i/sun5i haven't been updated. This results in the phy
driver failing to load, breaking usb support.
Fixes: 6827a46f59 ('phy: sun4i: add support for USB phy0')
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
much later than usual due to several last minute bugs that had to be
addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future which
will better parition clock providers from clock consumers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jD84
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
This is a follow-up to the early ARM SoC DT changes, with additional
content that has external dependencies:
* The Tegra IOMMU DT support depends on changes from the iommu
tree, plus the contents of the arm-soc drivers branch
* The MVEBU PHY support depends on changes from the phy tree
* The AT91 DT support depends on changes from the RTC and
DMA-slave trees
All of these changes just enable additional devices for
existing platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2PWh
-----END PGP SIGNATURE-----
Merge tag 'dt2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates part 2 from Arnd Bergmann:
"This is a follow-up to the early ARM SoC DT changes, with additional
content that has external dependencies:
- The Tegra IOMMU DT support depends on changes from the iommu tree,
plus the contents of the arm-soc drivers branch
- The MVEBU PHY support depends on changes from the phy tree
- The AT91 DT support depends on changes from the RTC and DMA-slave
trees
All of these changes just enable additional devices for existing
platforms"
* tag 'dt2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: Enable IOMMU for display controllers on Tegra124
ARM: tegra: Enable IOMMU for display controllers on Tegra114
ARM: tegra: Enable IOMMU for display controllers on Tegra30
ARM: tegra: Add memory controller support for Tegra124
ARM: tegra: Add memory controller support for Tegra114
ARM: tegra: Add memory controller support for Tegra30
ARM: tegra: Add APB_MISC_GP as a MIPI pad control bank
ARM: mvebu: add PHY support to the dts for the USB controllers on Armada 375
ARM: mvebu: add Device Tree description of USB cluster controller on Armada 375
ARM: at91/dt: at91sam9g45: add ISI node
ARM: at91/dt: enable the RTT block on the at91sam9m10g45ek board
ARM: at91/dt: enable the RTT block on the sam9g20ek board
ARM: at91/dt: add GPBR nodes
ARM: at91/dt: add RTT nodes to at91 dtsis
ARM: at91/dt: at91sam9rl: add rtc
ARM: at91: fix GPLv2 wording
ARM: at91/dt: sama5d4: add DMA support
ARM: at91/dt: sama5d4: use macro instead of numeric value
Here are the first arm-soc bug fixes. Most of these are OMAP related
fixes for regressions or minor bugs. Aside from that, there are a
few defconfig changes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mTqr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are the first arm-soc bug fixes. Most of these are OMAP related
fixes for regressions or minor bugs. Aside from that, there are a few
defconfig changes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu/exynos: Fix arm64 allmodconfig build
ARM: defconfigs: use CONFIG_CPUFREQ_DT
ARM: omap2plus_defconfig: Enable AHCI_PLATFORM driver
ARM: dts: am437x-sk-evm.dts: fix LCD timings
ARM: dts: dra7-evm: Update SMPS7 (VDD_CORE) max voltage to match DM
ARM: dts: dra7-evm: Fix typo in SMPS6 (VDD_GPU) max voltage
ARM: OMAP2+: AM43x: Add ID for ES1.2
ARM: dts: am437x-sk: fix lcd enable pin mux data
ARM: dts: Fix gpmc regression for omap 2430sdp smc91x
Revert "ARM: shmobile: multiplatform: add Audo DMAC peri peri support on defconfig"
ARM: dts: dra7: fix DSS PLL clock mux registers
ARM: dts: DRA7: wdt: Fix compatible property for watchdog node
ARM: OMAP2+: clock: remove unused function prototype
Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good thing,
but not at a huge rate this release, only about 70k lines removed
overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid details.
The "contentious" thing here is the movement of the Android binder code
out of staging into the "real" part of the kernel. This is code that
has been stable for a few years now and is working as-is in the tens of
millions of devices with no issues. Yes, the code is horrid, and the
userspace api leaves a lot to be desired, but it's not going to change
due to legacy issues that we have no control over. Because so many
devices and companies rely on this, and the code is stable, might as
well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been doing
it for the past few years with no problems. I'll send a MAINTAINERS
entry for it before 3.19-final is out, still need to talk to the Google
developers about if they are willing to help with it or not, last I
checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSPICkACgkQMUfUDdst+yksdwCfSLE9VUy1o2sAPDRe+J3bQced
EWEAoL3RtnejKbo5tHS2IT69pLrwiIDS
=YXyM
-----END PGP SIGNATURE-----
Merge tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good
thing, but not at a huge rate this release, only about 70k lines
removed overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid
details.
The "contentious" thing here is the movement of the Android binder
code out of staging into the "real" part of the kernel. This is code
that has been stable for a few years now and is working as-is in the
tens of millions of devices with no issues. Yes, the code is horrid,
and the userspace api leaves a lot to be desired, but it's not going
to change due to legacy issues that we have no control over. Because
so many devices and companies rely on this, and the code is stable,
might as well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been
doing it for the past few years with no problems. I'll send a
MAINTAINERS entry for it before 3.19-final is out, still need to talk
to the Google developers about if they are willing to help with it or
not, last I checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits)
Staging: slicoss: Fix long line issues in slicoss.c
staging: rtl8712: remove unnecessary else after return
staging: comedi: change some printk calls to pr_err
staging: rtl8723au: hal: Removed the extra semicolon
lustre: Deletion of unnecessary checks before three function calls
staging: lustre: fix sparse warnings: static function declaration
staging: lustre: fixed sparse warnings related to static declarations
staging: unisys: remove duplicate header
staging: unisys: remove unneeded structure
staging: ft1000 : replace __attribute ((__packed__) with __packed
drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c"
Drivers:staging:rtl8192e: Fixed checkpatch warning
Drivers:staging:clocking-wizard: Added a newline
staging: clocking-wizard: check for a valid clk_name pointer
staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts
staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily
staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1()
staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation
staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB()
staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation
...
Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a new
subsystem, "coresight" has been added. Full details are in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSODosACgkQMUfUDdst+ykSNwCfcqx1Z3rQzbLwSrR2sa1fV3Zb
yEAAniJoLZ4ZkoQK4/1ozsFc31q+gXNm
=/epr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
Pull crypto update from Herbert Xu:
- The crypto API is now documented :)
- Disallow arbitrary module loading through crypto API.
- Allow get request with empty driver name through crypto_user.
- Allow speed testing of arbitrary hash functions.
- Add caam support for ctr(aes), gcm(aes) and their derivatives.
- nx now supports concurrent hashing properly.
- Add sahara support for SHA1/256.
- Add ARM64 version of CRC32.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: tcrypt - Allow speed testing of arbitrary hash functions
crypto: af_alg - add user space interface for AEAD
crypto: qat - fix problem with coalescing enable logic
crypto: sahara - add support for SHA1/256
crypto: sahara - replace tasklets with kthread
crypto: sahara - add support for i.MX53
crypto: sahara - fix spinlock initialization
crypto: arm - replace memset by memzero_explicit
crypto: powerpc - replace memset by memzero_explicit
crypto: sha - replace memset by memzero_explicit
crypto: sparc - replace memset by memzero_explicit
crypto: algif_skcipher - initialize upon init request
crypto: algif_skcipher - removed unneeded code
crypto: algif_skcipher - Fixed blocking recvmsg
crypto: drbg - use memzero_explicit() for clearing sensitive data
crypto: drbg - use MODULE_ALIAS_CRYPTO
crypto: include crypto- module prefix in template
crypto: user - add MODULE_ALIAS
crypto: sha-mb - remove a bogus NULL check
crytpo: qat - Fix 64 bytes requests
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
- Force conversion of the ux500 pin control device trees
and parsers to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm
PMIC MPP pin controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller,
the first Intel pin controller to fully take advantage of
the pin control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sxpe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
Drop the vendor-prefix from the "ti,system-power-controller" device-tree
property name.
It has been agreed to make "system-power-controller" a standard property
and to drop the vendor-prefix that is currently used by several drivers.
Note that drivers that have used "<vendor>,system-power-controller" in a
released kernel will need to support both versions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Configure the RTC as system-power controller, which allows the system to
be powered off as well as woken up again on subsequent RTC alarms.
Note that the PMIC needs to be put in SLEEP (rather than OFF) mode to
maintain RTC power. Specifically, this means that the PMIC
ti,pmic-shutdown-controller property must be left unset in order to be
able to wake up on RTC alarms.
Tested on BeagleBone Black (rev A5).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lcd0 node for am437x-sk-evm.dts contains bad LCD timings, and while
they seem to work with a quick test, doing for example blank/unblank
will give you a black display.
This patch updates the timings to the 'typical' values from the LCD spec
sheet.
Also, the compatible string is completely bogus, as
"osddisplays,osd057T0559-34ts" is _not_ a 480x272 panel. The panel on
the board is a newhaven one. Update the compatible string to reflect
this. Note that this hasn't caused any issues, as the "panel-dpi"
matches the driver.
Cc: <stable@vger.kernel.org> # v3.17+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the latest Data Manual, for newer samples,
the nominal voltage required for VDD_CORE at OPP_NOM can be
upto 1.06V which was 1.03V earlier.
Update the regulator max voltage constraint for SMPS7,
connected to VDD_CORE, to meet this requirement.
Document reference:
DRA74 Data Manual, SPRS857M - Dec 2012, Revised Oct 2014.
DRA72 Data Manual, SPRS906G - Dec 2012, revised Oct 2014.
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The max expected voltage for VDD_GPU, connected to SMPS6, is 1.25V.
Correct regulator max voltage constraint to meet this requirement.
Document reference: DRA74 Data Manual, SPRS857M - Dec 2012,
Revised Oct 2014.
Fixes: c56a831ca4 ("ARM: dts: DRA7: Add TPS659038 PMIC nodes")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Caused by a copy & paste error. Note that even with
this bug AM437x SK display still works because GPIO
mux mode is always enabled. It's still wrong to mux
somebody else's pin.
Luckily ball D25 (offset 0x238 - gpio5_8) on AM437x
isn't used for anything.
While at that, also replace a pullup with a pulldown
as that gpio should be normally low, not high.
Cc: <stable@vger.kernel.org> # v3.17+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f4d809ec55b6 ("ARM: dts: Fix gpmc timings for omap 2430sdp")
added GPMC timings for 2430sdp. This however broke the Ethernet
for some versions of u-boot using a different L3 clock frequency:
set_gpmc_timing_reg: GPMC error! CS5: cs_rd_off: 233 ns, 39 ticks > 31
omap-gpmc 6e000000.gpmc: failed to set gpmc timings for: ethernet
This is because the smsc91x timings from 1.1.4 u-boot overflow the
GPMC registers when booted with 1.1.3 version of u-boot.
Let's fix this issue by using the better timings from u-boot 1.1.3
as they also work on 1.1.4 and are faster.
Note that so far the attempts over the years to calculate the GPMC
timings on the SDP boards have failed probably because of the
unknown latencies added by the FPGA on the debug boards.
Reported-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVIcjyGCrR//JCVInAQJJCRAA1Tm+HZGiAiTvXEAcm/T9tIA08uqtawHt
cqyEAUyrnE8QxE4EhUd2pTw4EunVusqKF5EsDxOzw7b3ukUdLAWZE7bqBOSIJLqn
hrfsQQ8dXLbyC7T/CHPnBVeM+pn9LiIc9qzpZ0YToiMnHBBI4vKFQntBjd31yoRE
hN08I6AmDjQolOzzlqR1fuM0uZaKiHIcytdauTt3Vfqgg7FTHcTy3u1kClHTR1Lp
m/KuDothGpR5OKjSnUQz7EO5V3KJEnaKey8z2xM1a7DLLAvJ6r2+DUaDopv9Dbz1
W/V3H7fi5tLvillVa8xmlmzqWZbPc1xw8MWqvHZSWIMRZqloAHpC1VWKn0ZuH4SW
5Bj4ubSrpYjJxjKYfrxtjmuzru3A2jWBNTSP5A4nsny0C3AUsXkfRmRS0VNdegF8
sUdQ1MF8vEMpQT3QPH88+ccFHeIgqbcayhKqLPf7r8q0kwlym5N7Y2amU2A/O6qz
+324r+yzfSA70VgJZ5EhXxWVDOPB4Lc8EtoWnH6T/kjncIMwzEsbEbyB3X1OaREW
pVn3PNo06VjHLYoiHX+8G99pOFR/JZvaQs6jGCXLs+Orjp5WfP+kafkWqcB5GAKU
Pfd3AQsl6rKAITdu0XsTdPiICNS4CmBiWYPepQsTa3pQaNgB7fwZNQKelNRIdGc+
dF1lnQ7CXLQ=
=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
* Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one
SoC at a time. For 3.19, the r8a7791 platform and associated\
"Koelsch" board are considered complete and we remove the non-DT
non-multiplatform support for this.
* The ARM Versatile Express has supported DT and multiplatform
for a long time, but we have still kept the legacy board files
around, because not all drivers were fully working before. We
have finally taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches
or just unrelated to the more interesting changes:
* The dts files for arm64 get moved into per-vendor directories for
a clearer structure.
* Some dead code removal (zynq, exynos, davinci, imx)
* Using pr_*() macros more consistently instead of printk(KERN_*)
in some platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Apdh
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been
doing the work de-facto by himself recently is now the
only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the
newly merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for
later rework (the current code is wrong in a harmless way), on
Tegra regression and one samsung spelling fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=J1gB
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been doing
the work de-facto by himself recently is now the only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the newly
merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for later
rework (the current code is wrong in a harmless way), on Tegra
regression and one samsung spelling fix"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6: fix bogus use of irq_get_irq_data
ARM: imx: irq: fix buggy usage of irq_data irq field
MAINTAINERS: ARM Versatile Express platform, add missing pattern
MAINTAINERS: ARM Versatile Express platform
arm: ep93xx: add dma_masks for the M2P and M2M DMA controllers
MAINTAINERS: Add ahci_st.c to ARCH/STI architecture
MAINTAINERS: add entry for the GISB arbiter driver
MAINTAINERS: update brcmstb entries
MAINTAINERS: update email address and cleanup for exynos entry
ARM: tegra: Re-add removed SoC id macro to tegra_resume()
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: OMAP: serial: remove last vestige of DTR_gpio support.
ARM: OMAP2+: gpmc: Get rid of "ti,elm-id not found" warning
ARM: EXYNOS: fix typo in static struct name "exynos5_list_diable_wfi_wfe"
ARM: OMAP2: Remove unnecessary KERN_* in omap_phy_internal.c
ARM: OMAP4+: Remove unused omap_l3_noc platform init
ARM: dts: Add twl keypad map for omap3 EVM
ARM: dts: Add twl keypad map for LDP
ARM: dts: Fix NAND last partition size on LDP
ARM: OMAP3: Fix errors for omap_l3_smx when booted with device tree
This will enable use of physical arch timers on rk3288, where each
core comes out of reset with a different virtual offset. Using
physical timers will help with SMP booting on coreboot and older
u-boot and should also allow suspend-resume and cpu-hotplug to work on
all firmwares.
Firmware which does initialize the cpu registers properly at boot and
cpu-hotplug can remove this property from the device tree.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
We now have the physical-timers patches lined up as a dependency in this same
branch, so we can revert the temporary disablement.
This reverts commit b77d43943e.
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the IRQ number to the main dts file and some new dts files
for newly added devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=epqY
-----END PGP SIGNATURE-----
Merge tag 'bcm5301x-dt-2014-12-04' of https://github.com/hauke/linux into next/dt
Merge "ARM: BCM5301X: DT changes for v3.19 #2" from Hauke Mehrtens:
ARM: BCM5301X: dts updates
This adds the IRQ number to the main dts file and some new dts files
for newly added devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tag 'bcm5301x-dt-2014-12-04' of https://github.com/hauke/linux:
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
Signed-off-by: Olof Johansson <olof@lixom.net>
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUffEUAAoJEPOmecmc0R2Bk4QH/0O8+misF7MM3/EX0UOicb09
zrrVaPfH8GKHz3NlXGNZhIgy1coNoElBmdWPEb+XI+tRI3vKcyHtsJp78XHYupBl
yHFXjRYw4dHwwc08cQRDzf8qfWFpTnKX/gSBhgn5+kuIvylalLmnY8RjYtuQcaYW
DEc5B8eEMmmDH1Y3UBat+JOIJZY4NWxc9zmK+wRuMtcLt8ieCmgOWVMBjl8BerAe
Vdi0EM3YicA/HDzPVNq3xQK6cUtWDfKSFvkJhwc9Q40Yl4LQaOf2YMA2sZ/4+Qnl
F1LLJtJFMo9A0vECDJIfleXJRXnq0VjVp1Mn18Do8J6zsazzS94ppSDyk5EliVg=
=jMaL
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "last dts changes for 3.19" from Jason Cooper:
- rk3288 thermal driver that got accepted into the thermal tree
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
* tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: dts: rockchip: enable thermal on rk3288-evb board
ARM: dts: rockchip: add main thermal info to rk3288
ARM: dts: rockchip: add RK3288 Thermal data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The bulk of these changes add memory controller nodes for Tegra30,
Tegra114 and Tegra124. The memory controller implements an IOMMU that
the display controllers are attached to. This allows them to scan out
physically non-contiguous framebuffers and removes one of the primary
users of CMA.
The only other change adds a new MIPI pad control bank to the pin
controller on Tegra124. The corresponding driver patch for this went
into v3.18 as:
3ccc11f6b8 pinctrl: tegra: Add MIPI pad control
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7LRQ
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt2
Pull "ARM: tegra: Device tree changes for v3.19" from Thierry Reding:
The bulk of these changes add memory controller nodes for Tegra30,
Tegra114 and Tegra124. The memory controller implements an IOMMU that
the display controllers are attached to. This allows them to scan out
physically non-contiguous framebuffers and removes one of the primary
users of CMA.
The only other change adds a new MIPI pad control bank to the pin
controller on Tegra124. The corresponding driver patch for this went
into v3.18 as:
3ccc11f6b8 pinctrl: tegra: Add MIPI pad control
* tag 'tegra-for-3.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable IOMMU for display controllers on Tegra124
ARM: tegra: Enable IOMMU for display controllers on Tegra114
ARM: tegra: Enable IOMMU for display controllers on Tegra30
ARM: tegra: Add memory controller support for Tegra124
ARM: tegra: Add memory controller support for Tegra114
ARM: tegra: Add memory controller support for Tegra30
ARM: tegra: Add APB_MISC_GP as a MIPI pad control bank
These additional commits are merged as dependencies:
memory: Add NVIDIA Tegra memory controller support
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
powerpc/iommu: Rename iommu_[un]map_sg functions
iommu: Improve error handling when setting bus iommu
iommu: Do more input validation in iommu_map_sg()
iommu: Add iommu_map_sg() function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
