IFC may have one or two interrupts. If two interrupt specifiers are
present, the first is the "common" interrupt (CM_EVTER_STAT), and the
second is the NAND interrupt (NAND_EVTER_STAT). If there is only one, that
interrupt reports both types of event.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
During suspend, all interrupts including IPI will be disabled. In this case,
the suspend process will hang in SMP. To prevent this, pass the flag
IRQF_NO_SUSPEND when requesting IPI irq.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The kernel crash was reported by Alexy. He was testing some feature
with private kernel, in which Alexy added some code in pci_pm_reset()
to read the CSR after writting it. The bug could be reproduced on
Fiber Channel card (Fibre Channel: Emulex Corporation Saturn-X:
LightPulse Fibre Channel Host Adapter (rev 03)) by the following
commands.
# echo 1 > /sys/devices/pci0004:01/0004:01:00.0/reset
# rmmod lpfc
# modprobe lpfc
The history behind the test case is that those additional config
space reading operations in pci_pm_reset() would cause EEH error,
but we didn't detect EEH error until "modprobe lpfc". For the case,
all the PCI devices on PCI bus (0004:01) were removed and added after
PE reset. Then the EEH devices would be figured out again based on
the OF nodes. Unfortunately, there were some child OF nodes under
PCI device (0004:01:00.0), but they didn't have attached PCI_DN since
they're invisible from PCI domain. However, we were still trying to
convert OF node to EEH device without checking on the attached PCI_DN.
Eventually, it caused the kernel crash as follows:
Unable to handle kernel paging request for data at address 0x00000030
Faulting instruction address: 0xc00000000004d888
cpu 0x0: Vector: 300 (Data Access) at [c000000fc797b950]
pc: c00000000004d888: .eeh_add_device_tree_early+0x78/0x140
lr: c00000000004d880: .eeh_add_device_tree_early+0x70/0x140
sp: c000000fc797bbd0
msr: 8000000000009032
dar: 30
dsisr: 40000000
current = 0xc000000fc78d9f70
paca = 0xc00000000edb0000 softe: 0 irq_happened: 0x00
pid = 2951, comm = eehd
enter ? for help
[c000000fc797bc50] c00000000004d848 .eeh_add_device_tree_early+0x38/0x140
[c000000fc797bcd0] c00000000004d848 .eeh_add_device_tree_early+0x38/0x140
[c000000fc797bd50] c000000000051b54 .pcibios_add_pci_devices+0x34/0x190
[c000000fc797bde0] c00000000004fb10 .eeh_reset_device+0x100/0x160
[c000000fc797be70] c0000000000502dc .eeh_handle_event+0x19c/0x300
[c000000fc797bf00] c000000000050570 .eeh_event_handler+0x130/0x1a0
[c000000fc797bf90] c000000000020138 .kernel_thread+0x54/0x70
The patch changes of_node_to_eeh_dev() and just returns NULL if the
passed OF node doesn't have attached PCI_DN.
Cc: stable@vger.kernel.org
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH core is talking with the PCI device driver to determine the
action (purely reset, or PCI device removal). During the period, the
driver might be unloaded and in turn causes kernel crash as follows:
EEH: Detected PCI bus error on PHB#4-PE#10000
EEH: This PCI device has failed 3 times in the last hour
lpfc 0004:01:00.0: 0:2710 PCI channel disable preparing for reset
Unable to handle kernel paging request for data at address 0x00000490
Faulting instruction address: 0xd00000000e682c90
cpu 0x1: Vector: 300 (Data Access) at [c000000fc75ffa20]
pc: d00000000e682c90: .lpfc_io_error_detected+0x30/0x240 [lpfc]
lr: d00000000e682c8c: .lpfc_io_error_detected+0x2c/0x240 [lpfc]
sp: c000000fc75ffca0
msr: 8000000000009032
dar: 490
dsisr: 40000000
current = 0xc000000fc79b88b0
paca = 0xc00000000edb0380 softe: 0 irq_happened: 0x00
pid = 3386, comm = eehd
enter ? for help
[c000000fc75ffca0] c000000fc75ffd30 (unreliable)
[c000000fc75ffd30] c00000000004fd3c .eeh_report_error+0x7c/0xf0
[c000000fc75ffdc0] c00000000004ee00 .eeh_pe_dev_traverse+0xa0/0x180
[c000000fc75ffe70] c00000000004ffd8 .eeh_handle_event+0x68/0x300
[c000000fc75fff00] c0000000000503a0 .eeh_event_handler+0x130/0x1a0
[c000000fc75fff90] c000000000020138 .kernel_thread+0x54/0x70
1:mon>
The patch increases the reference of the corresponding driver modules
while EEH core does the negotiation with PCI device driver so that the
corresponding driver modules can't be unloaded during the period and
we're safe to refer the callbacks.
Cc: stable@vger.kernel.org
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't do the real store operation for kprobing 'stwu Rx,(y)R1'
since this may corrupt the exception frame, now we will do this
operation safely in exception return code after migrate current
exception frame below the kprobed function stack.
So we only update gpr[1] here and trigger a thread flag to mask
this.
Note we should make sure if we trigger kernel stack over flow.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can't emulate stwu since that may corrupt current exception stack.
So we will have to do real store operation in the exception return code.
Firstly we'll allocate a trampoline exception frame below the kprobed
function stack and copy the current exception frame to the trampoline.
Then we can do this real store operation to implement 'stwu', and reroute
the trampoline frame to r1 to complete this exception migration.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to add a new thread flag, TIF_EMULATE_STACK_STORE,
for emulating stack store operation while exiting exception.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__get_user64() and __put_user64() are not used.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have missed lots of situations where the PE hierarchy tree need
protection through the EEH global mutex. The patch fixes that for
those public APIs implemented in eeh_pe.c. The only exception is
eeh_pe_restore_bars() because it calls eeh_pe_dev_traverse(), which
has been protected by the mutex.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function eeh_rmv_from_parent_pe() could be called by the path of
either normal PCI hotplug, or EEH recovery. For the former case,
we need purge the corresponding PE on removal of the associated
PE bus.
The patch tries to cover that by passing more information to function
pcibios_remove_pci_devices() so that we know if the corresponding PE
needs to be purged or be marked as "invalid".
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error happens on the PE whose PCI devices don't have
attached drivers. In function eeh_handle_event(), the default
value PCI_ERS_RESULT_NONE will be returned after iterating all
drivers of those PCI devices belonging to the PE. Actually, we
don't have installed drivers for the PCI devices. Under the
circumstance, we will remove the corresponding PCI bus of the PE,
including the associated EEH devices and PE instance. However,
we still need the information stored in the PE instance to do PE
reset after that. So it's unsafe to free the PE instance.
The patch introduces EEH_PE_INVALID type PE to address the issue.
When the PCI bus and the corresponding attached EEH devices are
removed, we will mark the PE as EEH_PE_INVALID. At later point,
the PE will be changed to EEH_PE_DEVICE or EEH_PE_BUS when the
corresponding EEH devices are attached again.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This was originally motivated by a desire to see the mapping between
logical and hardware cpu numbers.
But it seemed that it made more sense to just add a command to dump
(most of) the paca.
With no arguments "dp" will dump the paca for the current cpu.
It also takes an argument, eg. "dp 3" which is the logical cpu number
in hex. This form does not check if the cpu is possible, but displays
the paca regardless, as well as the cpu's state in the possible, present
and online masks.
Thirdly, "dpa" will display the paca for all possible cpus. If there are
no possible cpus, like early in boot, it will tell you that.
Sample output, number in brackets is the offset into the struct:
2:mon> dp 3
paca for cpu 0x3 @ c00000000ff20a80:
possible = yes
present = yes
online = yes
lock_token = 0x8000 (0x8)
paca_index = 0x3 (0xa)
kernel_toc = 0xc00000000144f990 (0x10)
kernelbase = 0xc000000000000000 (0x18)
kernel_msr = 0xb000000000001032 (0x20)
stab_real = 0x0 (0x28)
stab_addr = 0x0 (0x30)
emergency_sp = 0xc00000003ffe4000 (0x38)
data_offset = 0xa40000 (0x40)
hw_cpu_id = 0x9 (0x50)
cpu_start = 0x1 (0x52)
kexec_state = 0x0 (0x53)
__current = 0xc00000007e568680 (0x218)
kstack = 0xc00000007e5a3e30 (0x220)
stab_rr = 0x1a (0x228)
saved_r1 = 0xc00000007e7cb450 (0x230)
trap_save = 0x0 (0x240)
soft_enabled = 0x0 (0x242)
irq_happened = 0x0 (0x243)
io_sync = 0x0 (0x244)
irq_work_pending = 0x0 (0x245)
nap_state_lost = 0x0 (0x246)
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't need them anymore. The patch removes those functions.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the PCI probe flags "PCI_PROBE_ONLY | PCI_REASSIGN_ALL_RSRC"
used on powernv platform. That means the platform has to do the PCI
resource assignment by itself.
The patch changes the PCI probe flag to "PCI_REASSIGN_ALL_RSRC" so
that the PCI core will do the resource assignment. Also, the I/O
and MMIO minimal alignment for P2P bridges have been configured
while doing fixup for the PHBs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 arrays introduced to trace which PE has occupied the
corresponding resource (I/O or MMIO) segment. However, we didn't
allocate enough memory for them and that possiblly leads to PE
descriptor corruption.
The patch fixes that by allocating enough memory for those 2 arrays.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While the device driver or PCI core tries to enable PCI device, the
platform dependent callback "ppc_md.pcibios_enable_device_hook" will
be called to check if there has one associated PE for the PCI device.
If we don't have the associated PE for the PCI device, it's not allowed
to enable the PCI device. Unfortunately, there might have some cases
we have to enable the PCI device (e.g. P2P bridge), but the PEs have
not been created yet.
The patch handles the unfortunate cases. Each PHB (struct pnv_phb)
has one field "initialized" to trace if the PEs have been created
and configured or not. When the PEs are not available, we won't check
the associated PE for the PCI device to be enabled.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces additional wrapper function to call the original
implementation so that the DMA can be configured for all existing PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 types of PCI bus sensitive PEs: (A) The PE includes
single PCI bus. (B) The PE includes the PCI bus and all the subordinate
PCI buses, and the patch tries to assign I/O and MMIO resources
based on created PEs. Fortunately, we figured out unified scheme
to do resource assignment for all types of PCI bus based PEs according
to Ben's idea:
- Resource assignment based on PE from top to bottom.
- The soureces, either I/O or MMIO, of the PE are figured out
from the assigned PCI bus.
- The occupied resource by parent PE could possibilly be overrided
by children PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The resource (I/O and MMIO) will be assigned on basis of PE from
top to bottom so that we can implement the trick here: the resource
that has been assigned to parent PE could be taken by child PE if
necessary.
The current implementation already has PE list per PHB basis, but
the list doesn't meet our requirment: tracing PE based on their
cration time from top to bottom. So the patch does rename for the
DMA based PE list and introduces the list to trace the PEs sequentially
based on their creation time.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Basically, there're 2 types of PCI bus sensitive PEs: (A) The PE
includes single PCI bus. (B) The PE includes the PCI bus and all
the subordinate PCI buses. At present, we'd like to put PCI bus
originated by PCI-e link to form PE that contains single PCI bus,
and the PCIe-to-PCI bridge will form the 2nd type of PE. We don't
figure out to detect PLX bridge yet. Once we can detect PLX bridge
some day, we have to put PCI buses originated from the downstream
port of PLX bridge to the 2nd type of PE.
The patch changes the original implementation for a little bit
to support 2 types of PCI bus sensitive PEs described as above.
Also, the function used to retrieve the corresponding PE according
to the given PCI device has been changed based on that because each
PCI device should trace the directly associated PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a few tracepoints in the interrupt code path, which is before
irq_enter(), or after irq_exit(), like
trace_irq_entry()/trace_irq_exit() in do_IRQ(),
trace_timer_interrupt_entry()/trace_timer_interrupt_exit() in
timer_interrupt().
If the interrupt is from idle(), and because tracepoint contains RCU
read-side critical section, we could see following suspicious RCU usage
reported:
[ 145.127743] ===============================
[ 145.127747] [ INFO: suspicious RCU usage. ]
[ 145.127752] 3.6.0-rc3+ #1 Not tainted
[ 145.127755] -------------------------------
[ 145.127759] /root/.workdir/linux/arch/powerpc/include/asm/trace.h:33
suspicious rcu_dereference_check() usage!
[ 145.127765]
[ 145.127765] other info that might help us debug this:
[ 145.127765]
[ 145.127771]
[ 145.127771] RCU used illegally from idle CPU!
[ 145.127771] rcu_scheduler_active = 1, debug_locks = 0
[ 145.127777] RCU used illegally from extended quiescent state!
[ 145.127781] no locks held by swapper/0/0.
[ 145.127785]
[ 145.127785] stack backtrace:
[ 145.127789] Call Trace:
[ 145.127796] [c00000000108b530] [c000000000013c40] .show_stack
+0x70/0x1c0 (unreliable)
[ 145.127806] [c00000000108b5e0]
[c0000000000f59d8] .lockdep_rcu_suspicious+0x118/0x150
[ 145.127813] [c00000000108b680] [c00000000000fc58] .do_IRQ+0x498/0x500
[ 145.127820] [c00000000108b750] [c000000000003950]
hardware_interrupt_common+0x150/0x180
[ 145.127828] --- Exception: 501 at .plpar_hcall_norets+0x84/0xd4
[ 145.127828] LR = .check_and_cede_processor+0x38/0x70
[ 145.127836] [c00000000108bab0] [c0000000000665dc] .shared_cede_loop
+0x5c/0x100
[ 145.127844] [c00000000108bb70] [c000000000588ab0] .cpuidle_enter
+0x30/0x50
[ 145.127850] [c00000000108bbe0]
[c000000000588b0c] .cpuidle_enter_state+0x3c/0xb0
[ 145.127857] [c00000000108bc60] [c000000000589730] .cpuidle_idle_call
+0x150/0x6c0
[ 145.127863] [c00000000108bd30] [c000000000058440] .pSeries_idle
+0x10/0x40
[ 145.127870] [c00000000108bda0] [c00000000001683c] .cpu_idle
+0x18c/0x2d0
[ 145.127876] [c00000000108be60] [c00000000000b434] .rest_init
+0x124/0x1b0
[ 145.127884] [c00000000108bef0] [c0000000009d0d28] .start_kernel
+0x568/0x588
[ 145.127890] [c00000000108bf90] [c000000000009660] .start_here_common
+0x20/0x40
This is because the RCU usage in interrupt context should be used in
area marked by rcu_irq_enter()/rcu_irq_exit(), called in
irq_enter()/irq_exit() respectively.
Move them into the irq_enter()/irq_exit() area to avoid the reporting.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This update the proto-VSID and VSID scramble related information
to be more generic by using names instead of current values.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Increase max addressable range to 64TB. This is not tested on
real hardware yet.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With larger vsid we need to track more bits of ESID in slb cache
for slb invalidate.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ASM_VSID_SCRAMBLE can leave non-zero bits in the high 28 bits of the result
for 256MB segment (40 bits for 1T segment). Properly mask them before using
the values in slbmte
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch makes the high psizes mask as an unsigned char array
so that we can have more than 16TB. Currently we support upto
64TB
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As we keep increasing PGTABLE_RANGE we need not increase the virual
map area for kernel.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch convert different functions to take virtual page number
instead of virtual address. Virtual page number is virtual address
shifted right by VPN_SHIFT (12) bits. This enable us to have an
address range of upto 76 bits.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch simplify hpte_decode for easy switching of virtual address to
virtual page number in the later patch
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't open code the same
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To clarify the meaning for future readers, replace the open coded
19 with CONTEXT_BITS
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PTRS_PER_PUD should be based on PUD_INDEX_SIZE, not PMD_INDEX_SIZE. We
got away with it because PUD and PMD had the same index size, but this is
no longer true with Aneesh's patchset to support a 46-bit user effective
address space.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On POWER6 and POWER7 if the input operand to an instruction is a
denormalised single precision binary floating point value we can take
a denormalisation exception where it's expected that the hypervisor
(HV=1) will fix up the inputs before the instruction is run.
This adds code to handle this denormalisation exception for POWER6 and
POWER7.
It also add a CONFIG_PPC_DENORMALISATION option and sets it in
pseries/ppc64_defconfig.
This is useful on bare metal systems only. Based on patch from Milton
Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge Gavin patches from the PCI tree as subsequent powerpc
patches are going to depend on them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
We unified the Freescale pci/pcie initialization by changing the fsl_pci
to a platform driver. In previous PCI code architecture the initialization
routine is called at board_setup_arch stage. Now the initialization is done
in probe function which is architectural better. Also It's convenient for
adding PM support for PCI controller in later patch.
Now we registered pci controllers as platform devices. So we combine two
initialization code as one platform driver.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Freescale PCIe IP block revision bigger than rev2.2 will also need
redefine the sequence of inbound windows. So change to use IP block
revision instead of compatible for the judgment.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Device node adt7461 was wrongly added in p5040ds.dts, it should be added
into i2c instead of localbus, when build p5040ds.dtb, a warning will dump:
Warning (reg_format): "reg" property in
/localbus@ffe124000/nand@2,0/adt7461@4c has invalid length (4 bytes)
(#address-cells == 1, #size-cells == 1)
This was introduced by:
commit ea6b1ba692bcb5f6e39f409a78cf8b04fdf23baa
Author: Jia Hongtao <B38951@freescale.com>
Date: Tue Aug 28 10:00:55 2012 +0800
powerpc: add adt7461 thermal monitor support to applicable boards
Add thermal monitor support to following boards:
P1022DS, MPC8536DS, P2041RDB, P3041DS, P4080DS, P5020DS, P5040DS
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
create partition table for norflash.
Signed-off-by: Wang Dongsheng <Dongsheng.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add thermal monitor support to following boards:
P1022DS, MPC8536DS, P2041RDB, P3041DS, P4080DS, P5020DS, P5040DS
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Freescale's Integrated Flash controller(IFC) v1.1.0 supports 40 bit
address bus width.
In case more than 32 bit address is used, the EXT registers should be set.
Add support of ext registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
This patch update all the e5500 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all the e500mc platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all e500v2 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All SOC device error interrupts are muxed and delivered to the core
as a single MPIC error interrupt. Currently all the device drivers
requiring access to device errors have to register for the MPIC error
interrupt as a shared interrupt.
With this patch we add interrupt demuxing capability in the mpic driver,
allowing device drivers to register for their individual error interrupts.
This is achieved by handling error interrupts in a cascaded fashion.
MPIC error interrupt is handled by the "error_int_handler", which
subsequently demuxes it using the EISR and delivers it to the respective
drivers.
The error interrupt capability is dependent on the MPIC EIMR register,
which was introduced in FSL MPIC version 4.1 (P4080 rev2). So, error
interrupt demuxing capability is dependent on the MPIC version and can
be used for versions >= 4.1.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the dependency on PCI initialization for SWIOTLB initialization.
So that PCI can be initialized at proper time.
SWIOTLB is partly determined by PCI inbound/outbound map which is assigned
in PCI initialization. But swiotlb_init() should be done at the stage of
mem_init() which is much earlier than PCI initialization. So we reserve the
memory for SWIOTLB first and free it if not necessary.
All boards are converted to fit this change.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
