Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added power cap framework documentation. This explains the use of power
capping framework, sysfs and programming interface.
There are two documents:
- Documentation/power/powercap/powercap.txt : Explains use case and APIs.
- Documentation/ABI/testing/sysfs-class-powercap: Explains ABIs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For devices which don't have a .runtime_idle() callback or if it
returns 0, rpm_idle() will end up in triggering a call to
rpm_suspend(), thus trying to carry out a runtime suspend directly
from runtime_idle().
In the above situation we want to respect devices which has enabled
autosuspend, we therfore append the flag sent to rpm_suspend with
RPM_AUTO.
Do note that drivers still needs to update the device last busy mark,
to control the delay for this circumstance.
Updated runtime PM documentation accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The s2ram link is broken because there is a new OpenSuse wiki online.
The page does no longer exist, it was merged in the Suspend_to_RAM
page.
Signed-off-by: Jens Frederich <jfrederich@gmail.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Expand the existing documentation to explicitly list the options for
resuming a hibernation image, including the manual resume option which
can be used from the initrd or initramfs and the kernel init resume.
Signed-off-by: Sebastian Capella <sebastian.capella@linaro.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update PM QoS documentation after recent changes.
[rjw: Changelog]
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI video driver is written according to ACPI spec, appendix B: Video
Extensions. So it better be put under the acpi directory instead of the
power directory. This patch moves the file there without any other
change.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Runtime PM documentation needs to be updated after the previous
change of the rpm_idle() behavior, so modify it as appropriate.
[rjw: Subject and changelog]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Correct the meaning of PM_HIBERNATION_PREPARE in the docs.
References: http://lkml.kernel.org/r/20130512162717.GA6305@pd.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The lantency of the transition from suspend and hibernate is
platform-dependent. Thus we should not refer the lantency in the
documentation.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make Operating Performance Points (OPP) library introductory chapter
a little more reader-friendly. Split the chapter into two sections,
highlight the definition with an example and minor rewording to be
verbose.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At present, the value of timeout for freezing is 20s, which is
meaningless in case that one thread is frozen with mutex locked
and another thread is trying to lock the mutex, as this time of
freezing will fail unavoidably.
And if there is no new wakeup event registered, the system will
waste at most 20s for such meaningless trying of freezing.
With this patch, the value of timeout can be configured to smaller
value, so such meaningless trying of freezing will be aborted in
earlier time, and later freezing can be also triggered in earlier
time. And more power will be saved.
In normal case on mobile phone, it costs real little time to freeze
processes. On some platform, it only costs about 20ms to freeze
user space processes and 10ms to freeze kernel freezable threads.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This boolean function simply returns whether or not the runtime
status of the device is 'active'. The typical scenario is driver
calls pm_runtime_get firstly, then check pm_runtime_active in
atomic environment.
Also add entry to Documentation/power/runtime.txt
Signed-off-by: Yanmin Zhang <yanmin.zhang@intel.com>
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, the PM core disables runtime PM for all devices right
after executing subsystem/driver .suspend() callbacks for them
and re-enables it right before executing subsystem/driver .resume()
callbacks for them. This may lead to problems when there are
two devices such that the .suspend() callback executed for one of
them depends on runtime PM working for the other. In that case,
if runtime PM has already been disabled for the second device,
the first one's .suspend() won't work correctly (and analogously
for resume).
To make those issues go away, make the PM core disable runtime PM
for devices right before executing subsystem/driver .suspend_late()
callbacks for them and enable runtime PM for them right after
executing subsystem/driver .resume_early() callbacks for them. This
way the potential conflitcs between .suspend_late()/.resume_early()
and their runtime PM counterparts are still prevented from happening,
but the subtle ordering issues related to disabling/enabling runtime
PM for devices during system suspend/resume are much easier to avoid.
Reported-and-tested-by: Jan-Matthias Braun <jan_braun@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: 3.4+ <stable@vger.kernel.org>
The merge is merely to fix conflicts before sending a pull request.
Conflicts:
drivers/power/ab8500_btemp.c
drivers/power/ab8500_charger.c
drivers/power/ab8500_fg.c
drivers/power/abx500_chargalg.c
drivers/power/max8925_power.c
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add support for power supply attributes CHARGE_CONTROL_LIMIT
and CHARGE_CONTROL_LIMIT_MAX.
These new attributes will enable the user space to implement
custom charging algorithms based on platform state.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Modify the device PM QoS core code to support PM QoS flags requests.
First, add a new field of type struct pm_qos_flags called "flags"
to struct dev_pm_qos for representing the list of PM QoS flags
requests for the given device. Accordingly, add a new "type" field
to struct dev_pm_qos_request (along with an enum for representing
request types) and a new member called "flr" to its data union for
representig flags requests.
Second, modify dev_pm_qos_add_request(), dev_pm_qos_update_request(),
the internal routine apply_constraint() used by them and their
existing callers to cover flags requests as well as latency
requests. In particular, dev_pm_qos_add_request() gets a new
argument called "type" for specifying the type of a request to be
added.
Finally, introduce two routines, __dev_pm_qos_flags() and
dev_pm_qos_flags(), allowing their callers to check which PM QoS
flags have been requested for the given device (the caller is
supposed to pass the mask of flags to check as the routine's
second argument and examine its return value for the result).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic, and
chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable specific
regulators;
5. Random fixes and cleanups for other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=LkdH
-----END PGP SIGNATURE-----
Merge tag 'for-v3.7' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"1. New drivers:
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic,
and chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable
specific regulators;
5. Random fixes and cleanups for other drivers."
Fix up trivial conflicts in <linux/mfd/88pm860x.h>
* tag 'for-v3.7' of git://git.infradead.org/battery-2.6: (52 commits)
pda_power: Remove ac_draw_failed goto and label
charger-manager: Add support sysfs entry for charger
charger-manager: Support limit of maximum possible
charger-manager: Check fully charged state of battery periodically
lp8727_charger: More pure cosmetic improvements
lp8727_charger: Fix checkpatch warning
lp8727_charger: Add description in the private data
lp8727_charger: Fix a typo - chg_parm to chg_param
lp8727_charger: Make some cosmetic changes in lp8727_delayed_func()
lp8727_charger: Clean up lp8727_charger_changed()
lp8727_charger: Return if the battery is discharging
lp8727_charger: Make lp8727_charger_get_propery() simpler
lp8727_charger: Make lp8727_ctrl_switch() inline
lp8727_charger: Make lp8727_init_device() shorter
lp8727_charger: Clean up lp8727_is_charger_attached()
lp8727_charger: Use specific definition
lp8727_charger: Clean up lp8727 definitions
lp8727_charger: Use the definition rather than enum
lp8727_charger: Fix code for getting battery temp
lp8727_charger: Clear interrrupts at inital time
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
conversion to utf8 left some extra control character here,
remove it.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: John Anthony Kazos Jr <jakj@j-a-k-j.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are different types of chargers avalibale like AC, Solar, USB,
etc.. Even in USB we have different types SDP/DCP/CDP/ACA and all these
chargers have different o/p ratings. For example SDP supports only 500mA
of charge current whereas AC charger can support upto 8A or more.
Similarly batteries also come with charge current and voltage ratings
and these ratings vary depending on its capacity and the technology
used.
This patch adds two new power supply properties
CONSTANT_CHARGE_CURRENT_MAX and CONSTANT_CHARGE_CURRENT_MAX.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
It is possible that users can use non-standard chargers or use invalid
batteries especially with mobile devices.
This patch adds a new power supply property called 'AUTHENTIC' to
indicate this to the user(user space).
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that is)
caught the issue and it was decided[1] that I'd just delay the battery
pull request, and then will fix it up by merging upstream back into
battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem was
needed to get rid of a warning in power supply subsystem (the warning
was not drivers/power's "fault", the thermal registration function just
needed a proper const annotation, which is also done by a small commit
on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=1NaS
-----END PGP SIGNATURE-----
Merge tag 'for-v3.6' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"The tag contains just a few battery-related changes for v3.6. It's is
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that
is) caught the issue and it was decided[1] that I'd just delay the
battery pull request, and then will fix it up by merging upstream back
into battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem
was needed to get rid of a warning in power supply subsystem (the
warning was not drivers/power's "fault", the thermal registration
function just needed a proper const annotation, which is also done by
a small commit on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28"
* tag 'for-v3.6' of git://git.infradead.org/battery-2.6: (23 commits)
thermal: Constify 'type' argument for the registration routine
olpc-battery: update CHARGE_FULL_DESIGN property for BYD LiFe batteries
olpc-battery: Add VOLTAGE_MAX_DESIGN property
charger-manager: Fix build break related to EXTCON
lp8727_charger: Move header file into platform_data directory
power_supply: Add min/max alert properties for CAPACITY, TEMP, TEMP_AMBIENT
bq27x00_battery: Add support for BQ27425 chip
charger-manager: Set current limit of regulator for over current protection
charger-manager: Use EXTCON Subsystem to detect charger cables for charging
test_power: Add VOLTAGE_NOW and BATTERY_TEMP properties
test_power: Add support for USB AC source
gpio-charger: Use cansleep version of gpio_set_value
bq27x00_battery: Add support for power average and health properties
sbs-battery: Don't trigger false supply_changed event
twl4030_charger: Allow charger to control the regulator that feeds it
twl4030_charger: Add backup-battery charging
twl4030_charger: Fix some typos
max17042_battery: Support CHARGE_COUNTER power supply attribute
smb347-charger: Add constant charge and current properties
power_supply: Add constant charge_current and charge_voltage properties
...
Minimum and maximum alerts on power supply properties will help or allow
the user space to "proactively" create policies like connect/disconnect
charger or stop/start the user apps based on capacity or temperature
parameters.
These parameters can be used to avoid unnecessary polling from user space
and even from kernel space if the underlying HW can support INT triggers
(ex: max17042/47).
This patch adds the following power supply alert type properties:
CAPACITY_ALERT_MIN
CAPACITY_ALERT_MAX
TEMP_ALERT_MIN
TEMP_ALERT_MAX
TEMP_AMBIENT_ALERT_MIN
TEMP_AMBIENT_ALERT_MAX
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
It is often useful to suspend to memory after hibernation image has been
written to disk. If the battery runs out or power is otherwise lost, the
computer will resume from the hibernated image. If not, it will resume
from memory and hibernation image will be discarded.
Signed-off-by: Bojan Smojver <bojan@rexursive.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Constant Charge Current(CC) is charging parameter which limit the
maximum current which can be pumped into the battery during charge cycle.
Constant Charge Voltage(CV) is also charging parameter which limit the
maximum voltage that battery can reach during charge cycle.
It is very common practice that at low or high temperatures we
do not charge the batteries upto it's fullest charge voltage
to avoid battery and user safety issues.
These sysfs properties will be useful for debug and to implement
certain user space policies like "Charging limited due to OverTemp".
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=B6u0
-----END PGP SIGNATURE-----
Merge tag 'for-v3.5' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"A bunch of fixes for v3.5, nothing extraordinary."
* tag 'for-v3.5' of git://git.infradead.org/battery-2.6: (27 commits)
smb347-charger: Include missing <linux/err.h>
smb347-charger: Clean up battery attributes
max17042_battery: Add support for max17047/50 chip
sbs-battery.c: Capacity attr = remaining relative capacity
isp1704_charger: Use after free on probe error
ds2781_battery: Use DS2781_PARAM_EEPROM_SIZE and DS2781_USER_EEPROM_SIZE
power_supply: Fix a typo in BATTERY_DS2781 Kconfig entry
charger-manager: Provide cm_notify_event function for in-kernel use
charger-manager: Poll battery health in normal state
smb347-charger: Convert to regmap API
smb347-charger: Move IRQ enabling to the end of probe
smb347-charger: Rename few functions to match better what they are doing
smb347-charger: Convert to use module_i2c_driver()
smb347_charger: Cleanup power supply registration code in probe
ab8500: Clean up probe routines
ab8500_fg: Harden platform data check
ab8500_btemp: Harden platform data check
ab8500_charger: Harden platform data check
MAINTAINERS: Fix 'F' entry for the power supply class
max17042_battery: Handle irq request failure case
...
* Implementation of opportunistic suspend (autosleep) and user space interface
for manipulating wakeup sources.
* Hibernate updates from Bojan Smojver and Minho Ban.
* Updates of the runtime PM core and generic PM domains framework related to
PM QoS.
* Assorted fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Q2vo
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- Implementation of opportunistic suspend (autosleep) and user space
interface for manipulating wakeup sources.
- Hibernate updates from Bojan Smojver and Minho Ban.
- Updates of the runtime PM core and generic PM domains framework
related to PM QoS.
- Assorted fixes.
* tag 'pm-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
epoll: Fix user space breakage related to EPOLLWAKEUP
PM / Domains: Make it possible to add devices to inactive domains
PM / Hibernate: Use get_gendisk to verify partition if resume_file is integer format
PM / Domains: Fix computation of maximum domain off time
PM / Domains: Fix link checking when add subdomain
PM / Sleep: User space wakeup sources garbage collector Kconfig option
PM / Sleep: Make the limit of user space wakeup sources configurable
PM / Documentation: suspend-and-cpuhotplug.txt: Fix typo
PM / Domains: Cache device stop and domain power off governor results, v3
PM / Domains: Make device removal more straightforward
PM / Sleep: Fix a mistake in a conditional in autosleep_store()
epoll: Add a flag, EPOLLWAKEUP, to prevent suspend while epoll events are ready
PM / QoS: Create device constraints objects on notifier registration
PM / Runtime: Remove device fields related to suspend time, v2
PM / Domains: Rework default domain power off governor function, v2
PM / Domains: Rework default device stop governor function, v2
PM / Sleep: Add user space interface for manipulating wakeup sources, v3
PM / Sleep: Add "prevent autosleep time" statistics to wakeup sources
PM / Sleep: Implement opportunistic sleep, v2
PM / Sleep: Add wakeup_source_activate and wakeup_source_deactivate tracepoints
...
By using cm_notify_event function, charger driver can report several
charger events (e.g. battery full and external power in/out, etc) to
Charger-Manager. Charger-Manager can properly and immediately control
chargers by the reported event.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Charger-Manager needs to check battery health in normal state
as well as suspend-to-RAM state. When the battery is fully charged,
Charger-Manager needs to determine when the chargers restart charging.
This patch allows Charger-Manager to monitor battery health in normal
state and handle operation for chargers after battery is fully charged.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
sysfs was expected in this context.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This adds a new sysfs file called 'voltage_ocv' which gives the
Open Circuit Voltage of the battery.
This property can be used for platform shutdown policies and
can be useful for initial capacity estimations.
Note: This patch is generated against linux-next branch.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The file Documentation/power/freezing-of-tasks.txt was still referencing
the TIF_FREEZE flag, that was removed by the commit
d88e4cb67197d007fb778d62fe17360e970d5bfa(freezer: remove now unused
TIF_FREEZE).
This patch removes all the references of TIF_FREEZE that were left
behind.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
commit c172708 "regulator: core: Use a struct to pass in regulator runtime
configuration" changed the regulator_register() API signature.
Update the Documentation accordingly to reflect the change in the function
signature.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The way the different freeze/thaw functions encapsulate each other are quite
lovely from a design point of view. And as a side-effect, the way in which
they are invoked (cleaning up on failure for example) differs significantly
from how usual functions are dealt with. This is because of the underlying
semantics that govern the freezing and thawing of various tasks.
This subtle aspect that differentiates these functions from the rest, is
worth documenting.
Many thanks to Tejun Heo for providing enlightenment on this topic.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current device suspend/resume phases during system-wide power
transitions appear to be insufficient for some platforms that want
to use the same callback routines for saving device states and
related operations during runtime suspend/resume as well as during
system suspend/resume. In principle, they could point their
.suspend_noirq() and .resume_noirq() to the same callback routines
as their .runtime_suspend() and .runtime_resume(), respectively,
but at least some of them require device interrupts to be enabled
while the code in those routines is running.
It also makes sense to have device suspend-resume callbacks that will
be executed with runtime PM disabled and with device interrupts
enabled in case someone needs to run some special code in that
context during system-wide power transitions.
Apart from this, .suspend_noirq() and .resume_noirq() were introduced
as a workaround for drivers using shared interrupts and failing to
prevent their interrupt handlers from accessing suspended hardware.
It appears to be better not to use them for other porposes, or we may
have to deal with some serious confusion (which seems to be happening
already).
For the above reasons, introduce new device suspend/resume phases,
"late suspend" and "early resume" (and analogously for hibernation)
whose callback will be executed with runtime PM disabled and with
device interrupts enabled and whose callback pointers generally may
point to runtime suspend/resume routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
In a paragraph, "kernel thread" is mistakenly written as "kernel". Fix this by
adding thread after word "kernel".
Changes are shown in multiple lines, as they are realigned to 80 col width.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
regulator: max8925: fix enabled/disabled judgement mistake
regulator: add regulator_bulk_force_disable function
regulator: pass regulator_register of_node in fixed voltage driver
regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
regulator: Enable supply regulator if child rail is enabled.
regulator: mc13892: Convert to devm_kzalloc()
regulator: mc13783: Convert to devm_kzalloc()
regulator: Fix checking return value of create_regulator
regulator: Fix the error handling if create_regulator fails
regulator: Export regulator_is_supported_voltage()
regulator: mc13892: add device tree probe support
regulator: mc13892: remove the unnecessary prefix from regulator name
regulator: Convert wm831x regulator drivers to devm_kzalloc()
regulator: da9052: Staticize non-exported symbols
regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
regulator: Update da9052-regulator for DT changes
regulator: DA9052/53 Regulator support
regulator: pass device_node to of_get_regulator_init_data()
regulator: If a single voltage is set with device tree then set apply_uV
...
Charger Manager provides power-supply-class aggregating
information from multiple chargers and a fuel-gauge.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Because battery health monitoring should be done even when suspended,
it needs to wake up and suspend periodically. Thus, userspace battery
monitoring may incur too much overhead; every device and task is woken
up periodically. Charger Manager uses suspend-again to provide
in-suspend monitoring.
This patch allows to monitor battery health in-suspend state.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Make the PM core execute driver PM callbacks directly if the
corresponding subsystem callbacks are not present.
There are three reasons for doing that. First, it reflects the
behavior of drivers/base/dd.c:really_probe() that runs the driver's
.probe() callback directly if the bus type's one is not defined, so
this change will remove one arbitrary difference between the PM core
and the remaining parts of the driver core. Second, it will allow
some subsystems, whose PM callbacks don't do anything except for
executing driver callbacks, to be simplified quite a bit by removing
those "forward-only" callbacks. Finally, it will allow us to remove
one level of indirection in the system suspend and resume code paths
where it is not necessary, which is going to lead to less debug noise
with initcall_debug passed in the kernel command line (messages won't
be printed for driverless devices whose subsystems don't provide
PM callbacks among other things).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* master: (848 commits)
SELinux: Fix RCU deref check warning in sel_netport_insert()
binary_sysctl(): fix memory leak
mm/vmalloc.c: remove static declaration of va from __get_vm_area_node
ipmi_watchdog: restore settings when BMC reset
oom: fix integer overflow of points in oom_badness
memcg: keep root group unchanged if creation fails
nilfs2: potential integer overflow in nilfs_ioctl_clean_segments()
nilfs2: unbreak compat ioctl
cpusets: stall when updating mems_allowed for mempolicy or disjoint nodemask
evm: prevent racing during tfm allocation
evm: key must be set once during initialization
mmc: vub300: fix type of firmware_rom_wait_states module parameter
Revert "mmc: enable runtime PM by default"
mmc: sdhci: remove "state" argument from sdhci_suspend_host
x86, dumpstack: Fix code bytes breakage due to missing KERN_CONT
IB/qib: Correct sense on freectxts increment and decrement
RDMA/cma: Verify private data length
cgroups: fix a css_set not found bug in cgroup_attach_proc
oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
Revert "xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel"
...
Conflicts:
kernel/cgroup_freezer.c
Update the documentation to explain the perils of directly using
mutex_[un]lock(&pm_mutex) and recommend the usage of the safe
APIs [un]lock_system_sleep() instead.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The commit 2c043bcbf2 ("regulator: pass additional of_node to
regulator_register()") added an additional parameter to the
regulator_register() API.
Update the Documentation accordingly to reflect the change
in the function signature.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The system wakeup section of Documentation/power/devices.txt is
outdated, so make it agree with the current code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM core code behavior related to the power.irq_safe
device flag has changed recently and the documentation should be
modified to reflect it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The documentation file Documentation/power/devices.txt contains some
information that isn't correct any more due to code modifications
made after that file had been created (or updated last time). Fix
this.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current power management documentation in Documentation/power/
either doesn't cover PM domains at all, or gives inaccurate
information about them, so update the relevant files in there to
follow the code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There is no reason to export two functions for entering the
refrigerator. Calling refrigerator() instead of try_to_freeze()
doesn't save anything noticeable or removes any race condition.
* Rename refrigerator() to __refrigerator() and make it return bool
indicating whether it scheduled out for freezing.
* Update try_to_freeze() to return bool and relay the return value of
__refrigerator() if freezing().
* Convert all refrigerator() users to try_to_freeze().
* Update documentation accordingly.
* While at it, add might_sleep() to try_to_freeze().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
Cc: Christoph Hellwig <hch@infradead.org>
Some drivers set PF_NOFREEZE in their kthread functions which is
completely unnecessary and racy - some part of freezer code doesn't
consider cases where PF_NOFREEZE is set asynchronous to freezer
operations.
In general, there's no reason to allow setting PF_NOFREEZE explicitly.
Remove them and change the documentation to note that setting
PF_NOFREEZE directly isn't allowed.
-v2: Dropped change to twl4030-irq.c as it no longer uses PF_NOFREEZE.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "Gustavo F. Padovan" <padovan@profusion.mobi>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: wwang <wei_wang@realsil.com.cn>
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. Therefore
this patch (as1492) adds a mechanism for retrying failed
autosuspends. If the callback routine updates the last_busy field so
that the next autosuspend expiration time is in the future, the
autosuspend will automatically be rescheduled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch:
* Substitutes some obsolete references to kernel/power/process.c by
kernel/freezer.c.
* Mentions kernel/freezer.c as being part of the "freezer" code along
with the rest of the files.
* Fixes a trivial typo.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'for-linus' of git://opensource.wolfsonmicro.com/regulator: (22 commits)
regulator: Constify constraints name
regulator: Fix possible nullpointer dereference in regulator_enable()
regulator: gpio-regulator add dependency on GENERIC_GPIO
regulator: Add module.h include to gpio-regulator
regulator: Add driver for gpio-controlled regulators
regulator: remove duplicate REG_CTRL2 defines in tps65023
regulator: Clarify documentation for regulator-regulator supplies
regulator: Fix some bitrot in the machine driver documentation
regulator: tps65023: Added support for the similiar TPS65020 chip
regulator: tps65023: Setting correct core regulator for tps65021
regulator: tps65023: Set missing bit for update core-voltage
regulator: tps65023: Fixes i2c configuration issues
regulator: Add debugfs file showing the supply map table
regulator: tps6586x: add SMx slew rate setting
regulator: tps65023: Fixes i2c configuration issues
regulator: tps6507x: Remove num_voltages array
regulator: max8952: removed unused mutex.
regulator: fix regulator/consumer.h kernel-doc warning
regulator: Ensure enough enable time for max8649
regulator: 88pm8607: Fix off-by-one value range checking in the case of no id is matched
...
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
Update the documentation about the interaction between the suspend (S3) call
path and the CPU hotplug infrastructure.
This patch focusses only on the activities of the freezer, cpu hotplug and
the notifications involved. It outlines how regular CPU hotplug differs from
the way it is invoked during suspend and also tries to explain the locking
involved. In addition to that, it discusses the issue of microcode update
during CPU hotplug operations.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There is a problem with the current ordering of hibernate code which
leads to deadlocks in some filesystems' memory shrinkers. Namely,
some filesystems use freezable kernel threads that are inactive when
the hibernate memory preallocation is carried out. Those same
filesystems use memory shrinkers that may be triggered by the
hibernate memory preallocation. If those memory shrinkers wait for
the frozen kernel threads, the hibernate process deadlocks (this
happens with XFS, for one example).
Apparently, it is not technically viable to redesign the filesystems
in question to avoid the situation described above, so the only
possible solution of this issue is to defer the freezing of kernel
threads until the hibernate memory preallocation is done, which is
implemented by this change.
Unfortunately, this requires the memory preallocation to be done
before the "prepare" stage of device freeze, so after this change the
only way drivers can allocate additional memory for their freeze
routines in a clean way is to use PM notifiers.
Reported-by: Christoph <cr2005@u-club.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1485) documents a change to the kernel's default wakeup
policy. Devices that forward wakeup requests between buses should be
enabled for wakeup by default.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Record S3 failure time about each reason and the latest two failed
devices' names in S3 progress.
We can check it through 'suspend_stats' entry in debugfs.
The motivation of the patch:
We are enabling power features on Medfield. Comparing with PC/notebook,
a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far
more frequently. If it can't enter suspend-2-ram in time, the power
might be used up soon.
We often find sometimes, a device suspend fails. Then, system retries
s3 over and over again. As display is off, testers and developers
don't know what happens.
Some testers and developers complain they don't know if system
tries suspend-2-ram, and what device fails to suspend. They need
such info for a quick check. The patch adds suspend_stats under
debugfs for users to check suspend to RAM statistics quickly.
If not using this patch, we have other methods to get info about
what device fails. One is to turn on CONFIG_PM_DEBUG, but users
would get too much info and testers need recompile the system.
In addition, dynamic debug is another good tool to dump debug info.
But it still doesn't match our utilization scenario closely.
1) user need write a user space parser to process the syslog output;
2) Our testing scenario is we leave the mobile for at least hours.
Then, check its status. No serial console available during the
testing. One is because console would be suspended, and the other
is serial console connecting with spi or HSU devices would consume
power. These devices are powered off at suspend-2-ram.
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Support for device power domains has been introduced in
commit 9659cc0678 (PM: Make
system-wide PM and runtime PM treat subsystems consistently),
also power domain callbacks will take precedence over subsystem ones
from commit 4d27e9dcff00a6425d779b065ec8892e4f391661(PM: Make
power domain callbacks take precedence over subsystem ones).
So update part of "Device Runtime PM Callbacks" in
Documentation/power/runtime_pm.txt.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* pm-runtime:
PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
PM / Runtime: Replace dev_dbg() with trace_rpm_*()
PM / Runtime: Introduce trace points for tracing rpm_* functions
PM / Runtime: Don't run callbacks under lock for power.irq_safe set
USB: Add wakeup info to debugging messages
PM / Runtime: pm_runtime_idle() can be called in atomic context
PM / Runtime: Add macro to test for runtime PM events
PM / Runtime: Add might_sleep() to runtime PM functions
The mechanism used for connecting regulators together when one regulator
supplies another wasn't clear as the names being used weren't really tied
together well.
Reported-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The documentation for the machine driver was rather badly bitrotted,
using pointers to struct device rather than dev_name() to hook up the
consumers. Update to use dev_name().
Reported-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the documentation for the recently updated pm_qos API, kernel
and user space. Add documentation for the per-device PM QoS
(dev_pm_qos) framework API.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add to pm_runtime_idle the list of functions that can be called
in atomic context if pm_runtime_irq_safe() has been called for the
device.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The description of pm_runtime_irq_safe() has to be updated to follow
the code after commit 02b2677 (PM / Runtime: Allow _put_sync() from
interrupts-disabled context).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Some of the entry points to pm runtime are not safe to
call in atomic context unless pm_runtime_irq_safe() has
been called. Inspecting the code, it is not immediately
obvious that the functions sleep at all, as they run
inside a spin_lock_irqsave, but under some conditions
they can drop the lock and turn on irqs.
If a driver incorrectly calls the pm_runtime apis, it can
cause sleeping and irq processing when it expects to stay
in atomic context.
Add might_sleep_if to the majority of the __pm_runtime_* entry points
to enforce correct usage.
Add pm_runtime_put_sync_autosuspend to the list of
functions that can be called in atomic context.
Signed-off-by: Colin Cross <ccross@android.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently the use of pm_runtime_put_sync() is not safe from
interrupts-disabled context because rpm_idle() will release the
spinlock and enable interrupts for the idle callbacks. This enables
interrupts during a time where interrupts were expected to be
disabled, and can have strange side effects on drivers that expected
interrupts to be disabled.
This is not a bug since the documentation clearly states that only
_put_sync_suspend() is safe in IRQ-safe mode.
However, pm_runtime_put_sync() could be made safe when in IRQ-safe
mode by releasing the spinlock but not re-enabling interrupts, which
is what this patch aims to do.
Problem was found when using some buggy drivers that set
pm_runtime_irq_safe() and used _put_sync() in interrupts-disabled
context.
Reported-by: Colin Cross <ccross@google.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
* pm-domains: (33 commits)
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
PM / Domains: Make failing pm_genpd_prepare() clean up properly
PM / Domains: Set device state to "active" during system resume
ARM: mach-shmobile: sh7372 A3RV requires A4LC
PM / Domains: Export pm_genpd_poweron() in header
ARM: mach-shmobile: sh7372 late pm domain off
ARM: mach-shmobile: Runtime PM late init callback
ARM: mach-shmobile: sh7372 D4 support
ARM: mach-shmobile: sh7372 A4MP support
ARM: mach-shmobile: sh7372: make sure that fsi is peripheral of spu2
ARM: mach-shmobile: sh7372 A3SG support
...
cpufreq table allocated by opp_init_cpufreq_table is better
freed by OPP layer itself. This allows future modifications to
the table handling to be transparent to the users.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This boolean function simply returns whether or not the runtime status
of the device is 'suspended'. Unlike pm_runtime_suspended(), this
function returns the runtime status whether or not runtime PM for the
device has been disabled or not.
Also add entry to Documentation/power/runtime.txt
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM documentation and kerneldoc comments sometimes spell
"runtime" with a dash (i.e. "run-time"). Replace all of those
instances with "runtime" to make the naming consistent.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The runtime PM documentation in Documentation/power/runtime_pm.txt
doesn't say that pm_runtime_enable() and pm_runtime_disable() work by
operating on power.disable_depth, which is wrong, because the
possibility of nesting disables doesn't follow from the description
of these functions. Also, there is no description of
pm_runtime_barrier() at all in the document, which is confusing.
Improve the documentation by fixing those issues.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One of the roles of the PM core is to prevent different PM callbacks
executed for the same device object from racing with each other.
Unfortunately, after commit e866500247
(PM: Allow pm_runtime_suspend() to succeed during system suspend)
runtime PM callbacks may be executed concurrently with system
suspend/resume callbacks for the same device.
The main reason for commit e866500247
was that some subsystems and device drivers wanted to use runtime PM
helpers, pm_runtime_suspend() and pm_runtime_put_sync() in
particular, for carrying out the suspend of devices in their
.suspend() callbacks. However, as it's been determined recently,
there are multiple reasons not to do so, inlcuding:
* The caller really doesn't control the runtime PM usage counters,
because user space can access them through sysfs and effectively
block runtime PM. That means using pm_runtime_suspend() or
pm_runtime_get_sync() to suspend devices during system suspend
may or may not work.
* If a driver calls pm_runtime_suspend() from its .suspend()
callback, it causes the subsystem's .runtime_suspend() callback to
be executed, which leads to the call sequence:
subsys->suspend(dev)
driver->suspend(dev)
pm_runtime_suspend(dev)
subsys->runtime_suspend(dev)
recursive from the subsystem's point of view. For some subsystems
that may actually work (e.g. the platform bus type), but for some
it will fail in a rather spectacular fashion (e.g. PCI). In each
case it means a layering violation.
* Both the subsystem and the driver can provide .suspend_noirq()
callbacks for system suspend that can do whatever the
.runtime_suspend() callbacks do just fine, so it really isn't
necessary to call pm_runtime_suspend() during system suspend.
* The runtime PM's handling of wakeup devices is usually different
from the system suspend's one, so .runtime_suspend() may simply be
inappropriate for system suspend.
* System suspend is supposed to work even if CONFIG_PM_RUNTIME is
unset.
* The runtime PM workqueue is frozen before system suspend, so if
whatever the driver is going to do during system suspend depends
on it, that simply won't work.
Still, there is a good reason to allow pm_runtime_resume() to
succeed during system suspend and resume (for instance, some
subsystems and device drivers may legitimately use it to ensure that
their devices are in full-power states before suspending them).
Moreover, there is no reason to prevent runtime PM callbacks from
being executed in parallel with the system suspend/resume .prepare()
and .complete() callbacks and the code removed by commit
e866500247 went too far in this
respect. On the other hand, runtime PM callbacks, including
.runtime_resume(), must not be executed during system suspend's
"late" stage of suspending devices and during system resume's "early"
device resume stage.
Taking all of the above into consideration, make the PM core
acquire a runtime PM reference to every device and resume it if
there's a runtime PM resume request pending right before executing
the subsystem-level .suspend() callback for it. Make the PM core
drop references to all devices right after executing the
subsystem-level .resume() callbacks for them. Additionally,
make the PM core disable the runtime PM framework for all devices
during system suspend, after executing the subsystem-level .suspend()
callbacks for them, and enable the runtime PM framework for all
devices during system resume, right before executing the
subsystem-level .resume() callbacks for them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Some callers of pm_runtime_get_sync() and other runtime PM helper
functions, scsi_autopm_get_host() and scsi_autopm_get_device() in
particular, need to distinguish error codes returned when runtime PM
is disabled (i.e. power.disable_depth is nonzero for the given
device) from error codes returned in other situations. For this
reason, make the runtime PM helper functions return -EACCES when
power.disable_depth is nonzero and ensure that this error code
won't be returned by them in any other circumstances. Modify
scsi_autopm_get_host() and scsi_autopm_get_device() to check the
error code returned by pm_runtime_get_sync() and ignore -EACCES.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The documents describing the interactions between runtime PM and
system sleep generally refer to the model in which the system sleep
state is entered through a global firmware or hardware operation.
As a result, some recommendations given in there are not entirely
suitable for systems in which this is not the case. Update the
documentation to take the existence of those systems into account.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Introduce generic "noirq" power management callback routines for
subsystems in addition to the "regular" generic PM callback routines.
The new routines will be used, among other things, for implementing
system-wide PM transitions support for generic PM domains.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The naming convention used by commit 7538e3db6e015e890825fbd9f86599b
(PM: Add support for device power domains), which introduced the
struct dev_power_domain type for representing device power domains,
evidently confuses some developers who tend to think that objects
of this type must correspond to "power domains" as defined by
hardware, which is not the case. Namely, at the kernel level, a
struct dev_power_domain object can represent arbitrary set of devices
that are mutually dependent power management-wise and need not belong
to one hardware power domain. To avoid that confusion, rename struct
dev_power_domain to struct dev_pm_domain and rename the related
pointers in struct device and struct pm_clk_notifier_block from
pwr_domain to pm_domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Commit e1866b33b1 (PM / Runtime: Rework
runtime PM handling during driver removal) forgot to update the
documentation in Documentation/power/runtime_pm.txt to match the new
code in drivers/base/dd.c. Update that documentation to match the
code it describes.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Replace reference to pm_runtime_idle_sync() in the driver core with
pm_runtime_put_sync() which is used in the code.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit 4d27e9dcff (PM: Make power
domain callbacks take precedence over subsystem ones) forgot to
update the device power management documentation to take changes
made by it into account. Correct that mistake.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The part of Documentation/power/devices.txt regarding sysdevs is not
valid any more after commit 2e711c04db
(PM: Remove sysdev suspend, resume and shutdown operations), so
remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit e866500247 (PM: Allow
pm_runtime_suspend() to succeed during system suspend) removed usage
count increment across system PM.
Update doc to reflect this.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
supply_regulator_dev (using a struct pointer) has been deprecated in favour
of supply_regulator (using a regulator name) for quite a few releases
now with a warning generated if it is used and there are no current in tree
users so just remove the code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If device drivers allocate substantial amounts of memory (above 1 MB)
in their hibernate .freeze() callbacks (or in their legacy suspend
callbcks during hibernation), the subsequent creation of hibernate
image may fail due to the lack of memory. This is the case, because
the drivers' .freeze() callbacks are executed after the hibernate
memory preallocation has been carried out and the preallocated amount
of memory may be too small to cover the new driver allocations.
Unfortunately, the drivers' .prepare() callbacks also are executed
after the hibernate memory preallocation has completed, so they are
not suitable for allocating additional memory either. Thus the only
way a driver can safely allocate memory during hibernation is to use
a hibernate/suspend notifier. However, the notifiers are called
before the freezing of user space and the drivers wanting to use them
for allocating additional memory may not know how much memory needs
to be allocated at that point.
To let device drivers overcome this difficulty rework the hibernation
sequence so that the memory preallocation is carried out after the
drivers' .prepare() callbacks have been executed, so that the
.prepare() callbacks can be used for allocating additional memory
to be used by the drivers' .freeze() callbacks. Update documentation
to match the new behavior of the code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The code handling system-wide power transitions (eg. suspend-to-RAM)
can in theory execute callbacks provided by the device's bus type,
device type and class in each phase of the power transition. In
turn, the runtime PM core code only calls one of those callbacks at
a time, preferring bus type callbacks to device type or class
callbacks and device type callbacks to class callbacks.
It seems reasonable to make them both behave in the same way in that
respect. Moreover, even though a device may belong to two subsystems
(eg. bus type and device class) simultaneously, in practice power
management callbacks for system-wide power transitions are always
provided by only one of them (ie. if the bus type callbacks are
defined, the device class ones are not and vice versa). Thus it is
possible to modify the code handling system-wide power transitions
so that it follows the core runtime PM code (ie. treats the
subsystem callbacks as mutually exclusive).
On the other hand, the core runtime PM code will choose to execute,
for example, a runtime suspend callback provided by the device type
even if the bus type's struct dev_pm_ops object exists, but the
runtime_suspend pointer in it happens to be NULL. This is confusing,
because it may lead to the execution of callbacks from different
subsystems during different operations (eg. the bus type suspend
callback may be executed during runtime suspend of the device, while
the device type callback will be executed during system suspend).
Make all of the power management code treat subsystem callbacks in
a consistent way, such that:
(1) If the device's type is defined (eg. dev->type is not NULL)
and its pm pointer is not NULL, the callbacks from dev->type->pm
will be used.
(2) If dev->type is NULL or dev->type->pm is NULL, but the device's
class is defined (eg. dev->class is not NULL) and its pm pointer
is not NULL, the callbacks from dev->class->pm will be used.
(3) If dev->type is NULL or dev->type->pm is NULL and dev->class is
NULL or dev->class->pm is NULL, the callbacks from dev->bus->pm
will be used provided that both dev->bus and dev->bus->pm are
not NULL.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Reasoning-sounds-sane-to: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
